Update the DMTIMER compatibility property to reflect the register level
compatibilty between devices and update the various OMAP/AM timer
bindings with the appropriate compatibility string.
By doing this we can add platform specific data applicable to specific
timer versions to the driver. For example, errata flags can be populated
for the timer versions that are impacted.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
Add a function so that OMAP dmtimers can be requested by device-tree
node. This allows for devices, such as the internal DSP, or drivers,
such as PWM, to reference a specific dmtimer node via the device-tree.
Given that there are several APIs available for requesting dmtimers
(by ID, by capability or by node) consolidate the code for all these
functions into a single helper function that can be used by these
request functions.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
When booting with device-tree the function pointer for detecting context
loss is not populated. Ideally, the pm_runtime framework should be
enhanced to allow a means for reporting context/state loss and we could
avoid populating such function pointers altogether. In the interim until
a generic non-device specific solution is in place, force a restore of
the dmtimer when enabling the timer.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
The context loss handling in dmtimer appears to assume that
omap_dm_timer_set_load_start() or omap_dm_timer_start() and
omap_dm_timer_stop() bracket all interactions. Only the first two
restore the context and the last updates the context loss counter.
However omap_dm_timer_set_load() or omap_dm_timer_set_match() can
reasonably be called outside this bracketing, and the fact that they
call omap_dm_timer_enable() / omap_dm_timer_disable() suggest that
is expected.
So if, after a transition into and out of off-mode which would cause
the dm timer to loose all state, omap_dm_timer_set_match() is called
before omap_dm_timer_start(), the value read from OMAP_TIMER_CTRL_REG
will be 'wrong' and this wrong value will be stored context.tclr so
a subsequent omap_dm_timer_start() can fail (As the control register
is wrong).
Simplify this be doing the restore-from-context in
omap_dm_timer_enable() so that whenever the timer is enabled, the
context is correct. Also update the ctx_loss_count at the same time as
we notice it is wrong - these is no value in delaying this until the
omap_dm_timer_disable() as it cannot change while the timer is enabled.
Signed-off-by: NeilBrown <neilb@suse.de>
[jon-hunter@ti.com: minor update to subject and changed variable name]
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
This branch contains changes for OMAP that came in late during the release
staging, close to when the merge window opened.
It contains, among other things:
- OMAP PM fixes and some patches for audio device integration
- OMAP clock fixes related to common clock conversion
- A set of patches cleaning up WFI entry and blocking.
- A set of fixes and IP block support for PM on TI AM33xx SoCs (Beaglebone, etc)
- A set of smaller fixes and cleanups around AM33xx restart and revision
detection, as well as removal of some dead code (CONFIG_32K_TIMER_HZ)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=/vBT
-----END PGP SIGNATURE-----
Merge tag 'late-omap' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late OMAP changes from Olof Johansson:
"This branch contains changes for OMAP that came in late during the
release staging, close to when the merge window opened.
It contains, among other things:
- OMAP PM fixes and some patches for audio device integration
- OMAP clock fixes related to common clock conversion
- A set of patches cleaning up WFI entry and blocking.
- A set of fixes and IP block support for PM on TI AM33xx SoCs
(Beaglebone, etc)
- A set of smaller fixes and cleanups around AM33xx restart and
revision detection, as well as removal of some dead code
(CONFIG_32K_TIMER_HZ)"
* tag 'late-omap' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: omap2: include linux/errno.h in hwmod_reset
ARM: OMAP2+: fix some omap_device_build() calls that aren't compiled by default
ARM: OMAP4: hwmod data: Enable AESS hwmod device
ARM: OMAP4: hwmod data: Update AESS data with memory bank area
ARM: OMAP4+: AESS: enable internal auto-gating during initial setup
ASoC: TI AESS: add autogating-enable function, callable from architecture code
ARM: OMAP2+: hwmod: add enable_preprogram hook
ARM: OMAP4: clock data: Add missing clkdm association for dpll_usb
ARM: OMAP2+: PM: Fix the dt return condition in pm_late_init()
ARM: OMAP2: am33xx-hwmod: Fix "register offset NULL check" bug
ARM: OMAP2+: AM33xx: hwmod: add missing HWMOD_NO_IDLEST flags
ARM: OMAP: AM33xx hwmod: Add parent-child relationship for PWM subsystem
ARM: OMAP: AM33xx hwmod: Corrects PWM subsystem HWMOD entries
ARM: DTS: AM33XX: Add nodes for OCMC RAM and WKUP-M3
ARM: OMAP2+: AM33XX: Update the hardreset API
ARM: OMAP2+: AM33XX: hwmod: Update the WKUP-M3 hwmod with reset status bit
ARM: OMAP2+: AM33XX: hwmod: Fixup cpgmac0 hwmod entry
ARM: OMAP2+: AM33XX: hwmod: Update TPTC0 hwmod with the right flags
ARM: OMAP2+: AM33XX: hwmod: Register OCMC RAM hwmod
ARM: OMAP2+: AM33XX: CM/PRM: Use __ASSEMBLER__ macros in header files
...
Use the correct IS_ERR() to determine if clk_get() returned an error.
Set timer->fclk to be an error value initially, and check everywhere
using IS_ERR(). This keeps the range of valid values for 'struct clk'
consistent.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Converting more ARM platforms to multiplatform support. This time, OMAP
gets converted, which is a major step since this is by far the largest
platform in terms of code size. The same thing happens to the vt8500
platform.
Conflicts include:
* Two mach/uncompress.h files are removed, the changes made to them
elsewhere can be discarded now.
* Moving the OMAP4 irq_match array has context clashes with turning
omap4_sar_ram_init into an omap_early_initcall()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=nl4h
-----END PGP SIGNATURE-----
Merge tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform support from Arnd Bergmann:
"Converting more ARM platforms to multiplatform support. This time,
OMAP gets converted, which is a major step since this is by far the
largest platform in terms of code size. The same thing happens to the
vt8500 platform."
* tag 'multiplatform' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
net: cwdavinci_cpdma: export symbols for cpsw
remoteproc: omap: depend on OMAP_MBOX_FWK
[media] davinci: do not include mach/hardware.h
ARM: OMAP2+: Make sure files with omap initcalls include soc.h
ARM: OMAP2+: Include soc.h to drm.c to fix compiling
ARM: OMAP2+: Fix warning for hwspinlock omap_postcore_initcall
ARM: multi_v7_defconfig: add ARCH_ZYNQ
ARM: multi_v7_defconfig: remove unnecessary CONFIG_GPIOLIB
arm: vt8500: Remove remaining mach includes
arm: vt8500: Convert debug-macro.S to be multiplatform friendly
arm: vt8500: Remove single platform Kconfig options
ARM: OMAP2+: Remove now obsolete uncompress.h and debug-macro.S
ARM: OMAP2+: Add minimal support for booting vexpress
ARM: OMAP2+: Enable ARCH_MULTIPLATFORM support
ARM: OMAP2+: Disable code that currently does not work with multiplaform
ARM: OMAP2+: Add multiplatform debug_ll support
ARM: OMAP: Fix dmaengine init for multiplatform
ARM: OMAP: Fix i2c cmdline initcall for multiplatform
ARM: OMAP2+: Use omap initcalls
ARM: OMAP2+: Limit omap initcalls to omap only on multiplatform kernels
Bug fixes that did not make it into v3.8, mostly because they were not
considered important enough, and in some cases because bugs only show
up in combination with other patches destined for 3.9.
This includes a few larger patches for GPIO on the Marvell PXA platform
and a lot of Samsung specific bug fixes, as well as a series from Arnd
to fix older build warnings.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIVAwUAUSUyI2CrR//JCVInAQKBlRAAwOc8vTQl6UHciwibXXdMfL83hH0YNwu8
CFjnzHpvDX0YUQvW9fFPSq64CejhQumgaJYq3Te7mZW50H4hqGNqgFojPZy+2yn1
eEIjvNrES9Sp2aJG7iT1Q9BqvWVis736W7z8kTJ6szcG5e3KGZoFNdAl9izeiHtv
CTR9o4+XVY00eKbafVU+KJ4+/ZdptEnIWiQsg1gzImrRw/PosL/lgjYYCeRXb866
W7qltcCdwILA8+5x4KcK9CDAQbt+G2lLsmHzH4OZ2gjZmKzvZcxTOfXxdA9439Ew
jol5rkSAXiWcsgB4kzSx7sMGyMNim1qAu9FmhUdYqSc8UBGnGcns/QOLiGZxq9uS
9UTkInWC9Kcy8vSIIbDBvTpEZbbA5arAuEObK2eEPWntp/UgmGiSJaQmYHY+u9yd
BokmfSLc5g+jnQBS/H//nvPkA0ZlpknGZAovyRpjzZzYiF3LiBtsIMagYH2jVwzn
bc633NYo5cNO9DSO8mXSG6LUJ0X5d2HrTkg7J5x9GgOr1xDaH0rFjAdCZFXSTSKu
LVy3xehuXcHK4zbEvtgq7cjKyeIDpW0psPCXjKz4Fsreq6waPN88fHx9mVnoanII
JY9Lq8xW/2CH8uEdPyKMss/SXdzsVIm8bR3veS3TgqZa/2maMj/EkdGmPISUUjBY
JN48myQQSZM=
=BbV4
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull non-critical ARM SoC bug fixes from Arnd Bergmann:
"Bug fixes that did not make it into v3.8, mostly because they were not
considered important enough, and in some cases because bugs only show
up in combination with other patches destined for 3.9. This includes
a few larger patches for GPIO on the Marvell PXA platform and a lot of
Samsung specific bug fixes, as well as a series from Arnd to fix older
build warnings."
* tag 'fixes-non-critical' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: SPEAr13xx: Enable CONFIG_ARCH_HAS_CPUFREQ
ARM: imx: MACH_MX31ADS_WM1133_EV1 needs REGULATOR_WM8350
scripts/sortextable: silence script output
ARM: s3c: i2c: add platform_device forward declaration
ARM: mvebu: allow selecting mvebu without Armada XP
ARM: pick Versatile by default for !MMU
ARM: integrator: fix build with INTEGRATOR_AP off
ARM: integrator/versatile: fix NOMMU warnings
ARM: sa1100: don't warn about mach/ide.h
ARM: shmobile: fix defconfig warning on CONFIG_USB
ARM: w90x900: fix legacy assembly syntax
ARM: samsung: fix assembly syntax for new gas
ARM: disable virt_to_bus/virt_to_bus almost everywhere
ARM: dts: Correct pin configuration of SD 4 for exynos4x12-pinctrl
ARM: SAMSUNG: Silence empty switch warning in fimc-core.h
ARM: SAMSUNG: Silence empty switch warning in sdhci.h
ARM: msm: proc_comm_boot_wait should not be __init
arm: vt8500: Update MAINTAINERS entry for arch-vt8500
ARM: integrator: ensure ap_syscon_base is initialised when !CONFIG_MMU
ARM: S5PV210: Fix early uart output in fifo mode
...
The timekeeping doesn't depend on HZ value in presence of fine grained
clocksource and hence there should not be any time drift because of HZ
value which was chosen to be divisor of 32768.
OMAP has been using HZ = 128 value to avoid any time drift issues
because of 32768 HZ clock. But with various measurements performed
with HZ = 100, no time drift is observed and it also proves the
point about HZ not having impact on time keeping on OMAP.
Very informative thread on this topic is here:
https://lkml.org/lkml/2013/1/29/435
Special thanks to John Stulz, Arnd Bergmann and Russell King for their
valuable suggestions.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
'omap_dma_reserve_channels' when used is suppose to be from command.
so, it alreay has value before 1st call of omap_system_dma_probe.
and it will never be changed again during running (not from ioctl).
but 'dma_lch_count' is zero before 1st call of omap_system_dma_probe.
so it will be failed for omap_dma_reserve_channels, when 1st call.
so, need use 'd->lch_count' instead of 'dma_lch_count' for judging.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Flip on multiplatform support for omap2+.
No changes to omap2plus_defconfig needed, but please note
that you may need to update your custom config files to
make sure you have:
CONFIG_ARCH_MULTIPLATFORM=y
CONFIG_ARCH_MULTI_V7=y
CONFIG_ARCH_OMAP2PLUS=y
And may need CONFIG_ARCH_MULTI_V6=y if booting omap2 boards.
Cc: Russell King <linux@arm.linux.org.uk>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
We still need to fix up few places for multiplatform support,
but that can proceed separately. Fix the issue by making the
problem drivers depends !ARCH_MULTIPLATFORM for now.
The remaining pieces that are not multiplatform compatible
for omap2+ SoCs are:
1. Some drivers are using custom omap_dm_timer calls
There are two drivers that are directly usign omap hardware
timers for PWM and DSP clocking: drivers/media/rc/ir-rx51.c and
drivers/staging/tidspbridge/core/dsp-clock.c. These can be
fixed for multiplatform by allowing a minimal set of hardware
timers to be accessed, and for some functionality by using the
hrtimer framework.
2. Hardware OMAP4_ERRATA_I688 needs to be fixed up
This can't be enabled for multiplatform configurations in
it's current form. It may be possible to fix it up to do
instruction replacement early on during init. Luckily it
looks like this errata does not seem to get hit with
mainline kernel code alone at least currently.
3. Legacy header needed for omap-sham.c
Looks like it still needs mach/irqs.h for omap1 that
does not exist for multiplatform systems. Just ifdef
it for now.
4. Mailbox is waiting to get moved to drivers
Disable it for now to avoid adding a dependency to the
mailbox patches.
Cc: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Sean Young <sean@mess.org>
Cc: "Víctor Manuel Jáquez Leal" <vjaquez@igalia.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: Omar Ramirez Luna <omar.ramirez@ti.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
[tony@atomide.com: updated to disable mailbox]
Signed-off-by: Tony Lindgren <tony@atomide.com>
We only want this initcall to run when the kernel is
booted on omap SoCs. Fix the issue by initializing the
the initcall from separately for omap1 and omap2+.
This fixes the issue for omap2+ multiplatform configs
as we are using omap_subsys_initcall there.
Tested-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
People are back from the holiday breaks, and it shows. Here are a bunch of
fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups,
a few __init annotation fixes and some error handling improvement
in their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to see
here, mostly from the OMAP PM changes, but nothing overly crazy.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=s9fE
-----END PGP SIGNATURE-----
Merge tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"People are back from the holiday breaks, and it shows. Here are a
bunch of fixes for a number of platforms:
- A couple of small fixes for Nomadik
- A larger set of changes for kirkwood/mvebu
- uart driver selection, dt clocks, gpio-poweroff fixups, a few
__init annotation fixes and some error handling improvement in
their xor dma driver.
- i.MX had a couple of minor fixes (and a critical one for flexcan2
clock setup)
- MXS has a small board fix and a framebuffer bugfix
- A set of fixes for Samsung Exynos, fixing default bootargs and some
Exynos5440 clock issues
- A set of OMAP changes including PM fixes and a few sparse warning
fixups
All in all a bit more positive code delta than we'd ideally want to
see here, mostly from the OMAP PM changes, but nothing overly crazy."
* tag 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: clps711x: Fix bad merge of clockevents setup
ARM: highbank: save and restore L2 cache and GIC on suspend
ARM: highbank: add a power request clear
ARM: highbank: fix secondary boot and hotplug
ARM: highbank: fix typos with hignbank in power request functions
ARM: dts: fix highbank cpu mpidr values
ARM: dts: add device_type prop to cpu nodes on Calxeda platforms
ARM: mx5: Fix MX53 flexcan2 clock
ARM: OMAP2+: am33xx-hwmod: Fix wrongly terminated am33xx_usbss_mpu_irqs array
pinctrl: mvebu: make pdma clock on dove mandatory
ARM: Dove: Add pinctrl clock to DT
dma: mv_xor: fix error handling for clocks
dma: mv_xor: fix error handling of mv_xor_channel_add()
arm: mvebu: Add missing ; for cpu node.
arm: mvebu: Armada XP MV78230 has only three Ethernet interfaces
arm: mvebu: Armada XP MV78230 has two cores, not one
clk: mvebu: Remove inappropriate __init tagging
ARM: Kirkwood: Use fixed-regulator instead of board gpio call
ARM: Kirkwood: Fix missing sdio clock
ARM: Kirkwood: Switch TWSI1 of 88f6282 to DT clock providers
...
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
logs are available here:
http://www.pwsan.com/omap/testlogs/prcm_fixes_b_3.8-rc/20130102120724/
The 3730 Beagle XM here has an intermittent failure mounting SD root,
but the suspicion right now is that this is due to a failing SD card,
rather than any change introduced by these patches.
This second version includes a few changes requested by Tony Lindgren.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=oUTN
-----END PGP SIGNATURE-----
Merge tag 'omap-fixes-a2-for-v3.8-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8-rc2/fixes
Some OMAP PRCM and sparse fixes against v3.8-rc1. A basic set of test
logs are available here:
http://www.pwsan.com/omap/testlogs/prcm_fixes_b_3.8-rc/20130102120724/
The 3730 Beagle XM here has an intermittent failure mounting SD root,
but the suspicion right now is that this is due to a failing SD card,
rather than any change introduced by these patches.
This second version includes a few changes requested by Tony Lindgren.
Commit bb77209432 ("ARM: OMAP: Move
omap2+ specific parts of sram.c to mach-omap2") adds some new sparse
warnings:
arch/arm/plat-omap/sram.c:43:6: warning: symbol 'omap_sram_push_address' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:65:6: warning: symbol 'omap_sram_reset' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:73:13: warning: symbol 'omap_map_sram' was not declared. Should it be static?
This second version fixes the warnings by including <plat/sram.h>, at
Tony's request.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
From Tony Lindgren:
Here are few more patches to finish the omap changes for
multiplatform conversion that are not strictly fixes, but
were too complex to do with the dependencies during the
merge window. Those are to move of serial-omap.h to
platform_data, and the removal of remaining cpu_is_omap
macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few
minimal omap2plus_defconfig updates.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=RE6Z
-----END PGP SIGNATURE-----
Merge tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull late ARM cleanups for omap from Olof Johansson:
"From Tony Lindgren:
Here are few more patches to finish the omap changes for multiplatform
conversion that are not strictly fixes, but were too complex to do
with the dependencies during the merge window. Those are to move of
serial-omap.h to platform_data, and the removal of remaining
cpu_is_omap macro usage outside mach-omap2.
Then there are several trivial fixes for typos and few minimal
omap2plus_defconfig updates."
* tag 'omap-late-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
arch/arm/mach-omap2/dpll3xxx.c: drop if around WARN_ON
OMAP2: Fix a typo - replace regist with register.
ARM/omap: use module_platform_driver macro
ARM: OMAP2+: PMU: Remove unused header
ARM: OMAP4: remove duplicated include from omap_hwmod_44xx_data.c
ARM: OMAP2+: omap2plus_defconfig: enable twl4030 SoC audio
ARM: OMAP2+: omap2plus_defconfig: Add tps65217 support
ARM: OMAP2+: enable devtmpfs and devtmpfs automount
ARM: OMAP2+: omap_twl: Change TWL4030_MODULE_PM_RECEIVER to TWL_MODULE_PM_RECEIVER
ARM: OMAP2+: Drop plat/cpu.h for omap2plus
ARM: OMAP: Split fb.c to remove last remaining cpu_is_omap usage
MAINTAINERS: Add an entry for omap related .dts files
Commit 1fe97c8f6a ("ARM: OMAP: Make OMAP
clocksource source selection using kernel param") results in a new warning
from sparse:
arch/arm/plat-omap/counter_32k.c:86:12: warning: symbol 'omap_init_clocksource_32k' was not declared. Should it be static?
This second version fixes this warning by including <plat/counter-32k.h>,
at Tony's request.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
This patch removes some code duplication by using
module_platform_driver.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The cpu_is_omap macros are now local to arch/arm/mach-omap2
in soc.h and plat/cpu.h can finally be dropped for omap2+.
Thanks everybody for help with fixing the drivers.
Note that we can now also remove the unused plat/cpu.h from
smartreflex.c and isp.c as they will cause compile errors
with ARCH_MULTIPLATFORM enabled.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Jean Pihet <jean.pihet@newoldbits.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we missed plat-omap/fb.c for cpu_is_omap usage
mach-omap2. This is the last user of cpu_is_omap, so let's
quickly fix it up so we can finally remove plat/cpu.h for
omap2lus.
We want to limit cpu_is_omap macro usage to mach-omap2 only so
we can make plat/cpu.h private. After this we can finally drop
plat/cpu.h for omap2+.
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAPDSS changes, including:
- use dynanic debug prints
- OMAP platform dependency removals
- Creation of compat-layer, helping us to improve omapdrm
- Misc cleanups, aiming to make omadss more in line with the upcoming common
display framework
Exynos DP changes for the 3.8 merge window:
- Device Tree support for Samsung Exynos DP
- SW Link training is cleaned up.
- HPD interrupt is supported.
Samsung Framebuffer changes for the 3.8 merge window:
- The bit definitions of header file are updated.
- Some minor typos are fixed.
- Some minor bugs of s3c_fb_check_var() are fixed.
FB related changes for SH Mobile, Freescale DIU
Add support for the Solomon SSD1307 OLED Controller
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=KVPX
-----END PGP SIGNATURE-----
Merge tag 'fbdev-for-3.8' of git://gitorious.org/linux-omap-dss2/linux
Pull fbdev changes from Tomi Valkeinen:
"OMAPDSS changes, including:
- use dynanic debug prints
- OMAP platform dependency removals
- Creation of compat-layer, helping us to improve omapdrm
- Misc cleanups, aiming to make omadss more in line with the upcoming
common display framework
Exynos DP changes for the 3.8 merge window:
- Device Tree support for Samsung Exynos DP
- SW Link training is cleaned up.
- HPD interrupt is supported.
Samsung Framebuffer changes for the 3.8 merge window:
- The bit definitions of header file are updated.
- Some minor typos are fixed.
- Some minor bugs of s3c_fb_check_var() are fixed.
FB related changes for SH Mobile, Freescale DIU
Add support for the Solomon SSD1307 OLED Controller"
* tag 'fbdev-for-3.8' of git://gitorious.org/linux-omap-dss2/linux: (191 commits)
OMAPDSS: fix TV-out issue with DSI PLL
Revert "OMAPFB: simplify locking"
OMAPFB: remove silly loop in fb2display()
OMAPFB: fix error handling in omapfb_find_best_mode()
OMAPFB: use devm_kzalloc to allocate omapfb2_device
OMAPDSS: DISPC: remove dispc fck uses
OMAPDSS: DISPC: get dss clock rate from dss driver
drivers/video/console/softcursor.c: remove redundant NULL check before kfree()
drivers/video: add support for the Solomon SSD1307 OLED Controller
OMAPDSS: use omapdss_compat_init() in other drivers
OMAPDSS: export dispc functions
OMAPDSS: export dss_feat functions
OMAPDSS: export dss_mgr_ops functions
OMAPDSS: separate compat files in the Makefile
OMAPDSS: move display sysfs init to compat layer
OMAPDSS: DPI: use dispc's check_timings
OMAPDSS: DISPC: add dispc_ovl_check()
OMAPDSS: move irq handling to dispc-compat
OMAPDSS: move omap_dispc_wait_for_irq_interruptible_timeout to dispc-compat.c
OMAPDSS: move blocking mgr enable/disable to compat layer
...
Conflicts:
arch/arm/mach-davinci/devices-da8xx.c
arch/arm/plat-omap/common.c
drivers/media/platform/omap/omap_vout.c
We need to move this file to allow ARM multiplatform configurations
to build for omap2+. This can now be done as this file now only
contains platform_data.
cc: Russell King <linux@arm.linux.org.uk>
cc: Alan Cox <alan@linux.intel.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Govindraj.R <govindraj.raja@ti.com>
cc: Kevin Hilman <khilman@ti.com>
cc: linux-serial@vger.kernel.org
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP2420 H4 board was the only board using the
plat-omap/debug-devices.c code for configuring ethernet support. Now
that OMAP2420 H4 has been migrated to use the generic gpmc code for
configuring ethernet support, the debug-devices.c file is no longer
used and so remove it and its header file.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=h2Qo
-----END PGP SIGNATURE-----
Merge tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC power management and clock changes from Olof Johansson:
"This branch contains a largeish set of updates of power management and
clock setup. The bulk of it is for OMAP/AM33xx platforms, but also a
few around hotplug/suspend/resume on Exynos.
It includes a split-up of some of the OMAP clock data into separate
files which adds to the diffstat, but gross delta is fairly reasonable."
* tag 'pm-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
ARM: EXYNOS: Add flush_cache_all in suspend finisher
ARM: EXYNOS: Remove scu_enable from cpuidle
ARM: EXYNOS: Fix soft reboot hang after suspend/resume
ARM: EXYNOS: Add support for rtc wakeup
ARM: EXYNOS: fix the hotplug for Cortex-A15
ARM: OMAP2+: omap_device: Correct resource handling for DT boot
ARM: OMAP2+: hwmod: Add possibility to count hwmod resources based on type
ARM: OMAP2+: hwmod: Add support for per hwmod/module context lost count
ARM: OMAP2+: PRM: initialize some PRM functions early
ARM: OMAP2+: voltage: fixup oscillator handling when CONFIG_PM=n
ARM: OMAP4: USB: power down MUSB PHY during boot
ARM: OMAP2+: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP2xxx: clock: drop obsolete clock data
ARM: OMAP2: clock: Cleanup !CONFIG_COMMON_CLK parts
ARM: OMAP3+: DPLL: drop !CONFIG_COMMON_CLK sections
ARM: AM33xx: clock: drop obsolete clock data
ARM: OMAP3xxx: clk: drop obsolete clock data
...
OMAPDSS changes for 3.8, including:
- use dynanic debug prints
- OMAP platform dependency removals
- Creation of compat-layer, helping us to improve omapdrm
- Misc cleanups, aiming to make omadss more in line with the upcoming common
display framework
* tag 'omapdss-for-3.8' of git://gitorious.org/linux-omap-dss2/linux: (140 commits)
OMAPDSS: fix TV-out issue with DSI PLL
Revert "OMAPFB: simplify locking"
OMAPFB: remove silly loop in fb2display()
OMAPFB: fix error handling in omapfb_find_best_mode()
OMAPFB: use devm_kzalloc to allocate omapfb2_device
OMAPDSS: DISPC: remove dispc fck uses
OMAPDSS: DISPC: get dss clock rate from dss driver
OMAPDSS: use omapdss_compat_init() in other drivers
OMAPDSS: export dispc functions
OMAPDSS: export dss_feat functions
OMAPDSS: export dss_mgr_ops functions
OMAPDSS: separate compat files in the Makefile
OMAPDSS: move display sysfs init to compat layer
OMAPDSS: DPI: use dispc's check_timings
OMAPDSS: DISPC: add dispc_ovl_check()
OMAPDSS: move irq handling to dispc-compat
OMAPDSS: move omap_dispc_wait_for_irq_interruptible_timeout to dispc-compat.c
OMAPDSS: move blocking mgr enable/disable to compat layer
OMAPDSS: manage framedone irq with mgr ops
OMAPDSS: add manager ops
...
Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to be
part of the multiplatform support -- the first "big" SoC that is moved
over (more multiplatform work comes in a separate branch later during
the merge window).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=zfPd
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups on various subarchitectures from Olof Johansson:
"Cleanup patches for various ARM platforms and some of their associated
drivers. There's also a branch in here that enables Freescale i.MX to
be part of the multiplatform support -- the first "big" SoC that is
moved over (more multiplatform work comes in a separate branch later
during the merge window)."
Conflicts fixed as per Olof, including a silent semantic one in
arch/arm/mach-omap2/board-generic.c (omap_prcm_restart() was renamed to
omap3xxx_restart(), and a new user of the old name was added).
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (189 commits)
ARM: omap: fix typo on timer cleanup
ARM: EXYNOS: Remove unused regs-mem.h file
ARM: EXYNOS: Remove unused non-dt support for dwmci controller
ARM: Kirkwood: Use hw_pci.ops instead of hw_pci.scan
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: SAMSUNG: use devm_ functions for ADC driver
ARM: EXYNOS: no duplicate mask/unmask in eint0_15
ARM: S3C24XX: SPI clock channel setup is fixed for S3C2443
ARM: EXYNOS: Remove i2c0 resource information and setting of device names
ARM: Kirkwood: checkpatch cleanups
ARM: Kirkwood: Fix sparse warnings.
ARM: Kirkwood: Remove unused includes
ARM: kirkwood: cleanup lsxl board includes
ARM: integrator: use BUG_ON where possible
ARM: integrator: push down SC dependencies
ARM: integrator: delete static UART1 mapping
ARM: integrator: delete SC mapping on the CP
ARM: integrator: remove static CP syscon mapping
ARM: integrator: remove static AP syscon mapping
...
This is a collection of header file cleanups, mostly for OMAP and AT91,
that keeps moving the platforms in the direction of multiplatform by
removing the need for mach-dependent header files used in drivers and
other places.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=aggA
-----END PGP SIGNATURE-----
Merge tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC Header cleanups from Olof Johansson:
"This is a collection of header file cleanups, mostly for OMAP and
AT91, that keeps moving the platforms in the direction of
multiplatform by removing the need for mach-dependent header files
used in drivers and other places."
Fix up mostly trivial conflicts as per Olof.
* tag 'headers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (106 commits)
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
atmel: move ATMEL_MAX_UART to platform_data/atmel.h
ARM: OMAP: Remove omap_init_consistent_dma_size()
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
ARM: OMAP: Remove NEED_MACH_GPIO_H
ARM: OMAP: Remove unnecessary mach and plat includes
...
Pull ARM OMAP serial updates from Russell King:
"This series is a major reworking of the OMAP serial driver code fixing
various bugs in the hardware-assisted flow control, extending up into
serial_core for a couple of issues. These fixes have been done as a
set of progressive changes and transformations in the hope that no new
bugs will be introduced by this series.
The problems are many-fold, from the driver not being informed about
updated settings, to the driver not knowing what the intentions of the
upper layers are.
The first four patches tackle the serial_core layer, allowing it to
provide the necessary information to drivers, and the remaining
patches allow the OMAP serial driver to take advantage of this.
This brings hardware assisted RTS/CTS and XON/OFF flow control into a
useful state.
These patches have been in linux-next for most of the last cycle;
indeed they predate the previous merge window. They've also been
posted to the OMAP people."
* 'omap-serial' of git://git.linaro.org/people/rmk/linux-arm: (21 commits)
SERIAL: omap: fix hardware assisted flow control
SERIAL: omap: simplify (2)
SERIAL: omap: move xon/xoff setting earlier
SERIAL: omap: always set TCR
SERIAL: omap: simplify
SERIAL: omap: don't read back LCR/MCR/EFR
SERIAL: omap: serial_omap_configure_xonxoff() contents into set_termios
SERIAL: omap: configure xon/xoff before setting modem control lines
SERIAL: omap: remove OMAP_UART_SYSC_RESET and OMAP_UART_FIFO_CLR
SERIAL: omap: move driver private definitions and structures to driver
SERIAL: omap: remove 'irq_pending' bitfield
SERIAL: omap: fix MCR TCRTLR bit handling
SERIAL: omap: fix set_mctrl() breakage
SERIAL: omap: no need to re-read EFR
SERIAL: omap: remove setting of EFR SCD bit
SERIAL: omap: allow hardware assisted IXANY mode to be disabled
SERIAL: omap: allow hardware assisted rts/cts modes to be disabled
SERIAL: core: add throttle/unthrottle callbacks for hardware assisted flow control
SERIAL: core: add hardware assisted h/w flow control support
SERIAL: core: add hardware assisted s/w flow control support
...
Conflicts:
drivers/tty/serial/omap-serial.c
Here's the big tty/serial tree set of changes for 3.8-rc1.
Contained in here is a bunch more reworks of the tty port layer from Jiri and
bugfixes from Alan, along with a number of other tty and serial driver updates
by the various driver authors.
Also, Jiri has been coerced^Wconvinced to be the co-maintainer of the TTY
layer, which is much appreciated by me.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlDHhgwACgkQMUfUDdst+ynI6wCcC+YeBwncnoWHvwLAJOwAZpUL
bysAn28o780/lOsTzp3P1Qcjvo69nldo
=hN/g
-----END PGP SIGNATURE-----
Merge tag 'tty-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY/Serial merge from Greg Kroah-Hartman:
"Here's the big tty/serial tree set of changes for 3.8-rc1.
Contained in here is a bunch more reworks of the tty port layer from
Jiri and bugfixes from Alan, along with a number of other tty and
serial driver updates by the various driver authors.
Also, Jiri has been coerced^Wconvinced to be the co-maintainer of the
TTY layer, which is much appreciated by me.
All of these have been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fixed up some trivial conflicts in the staging tree, due to the fwserial
driver having come in both ways (but fixed up a bit in the serial tree),
and the ioctl handling in the dgrp driver having been done slightly
differently (staging tree got that one right, and removed both
TIOCGSOFTCAR and TIOCSSOFTCAR).
* tag 'tty-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (146 commits)
staging: sb105x: fix potential NULL pointer dereference in mp_chars_in_buffer()
staging/fwserial: Remove superfluous free
staging/fwserial: Use WARN_ONCE when port table is corrupted
staging/fwserial: Destruct embedded tty_port on teardown
staging/fwserial: Fix build breakage when !CONFIG_BUG
staging: fwserial: Add TTY-over-Firewire serial driver
drivers/tty/serial/serial_core.c: clean up HIGH_BITS_OFFSET usage
staging: dgrp: dgrp_tty.c: Audit the return values of get/put_user()
staging: dgrp: dgrp_tty.c: Remove the TIOCSSOFTCAR ioctl handler from dgrp driver
serial: ifx6x60: Add modem power off function in the platform reboot process
serial: mxs-auart: unmap the scatter list before we copy the data
serial: mxs-auart: disable the Receive Timeout Interrupt when DMA is enabled
serial: max310x: Setup missing "can_sleep" field for GPIO
tty/serial: fix ifx6x60.c declaration warning
serial: samsung: add devicetree properties for non-Exynos SoCs
serial: samsung: fix potential soft lockup during uart write
tty: vt: Remove redundant null check before kfree.
tty/8250 Add check for pci_ioremap_bar failure
tty/8250 Add support for Commtech's Fastcom Async-335 and Fastcom Async-PCIe cards
tty/8250 Add XR17D15x devices to the exar_handle_irq override
...
Core:
- Expose access to the eMMC RPMB ("Replay Protected Memory Block") area
by extending the existing mmc_block ioctl.
- Add SDIO powered-suspend DT properties to the core MMC DT binding.
- Add no-1-8-v DT flag for boards where the SD controller reports that it
supports 1.8V but the board itself has no way to switch to 1.8V.
- More work on switching to 1.8V UHS support using a vqmmc regulator.
- Fix up a case where the slot-gpio helper may fail to reset the host
controller properly if a card was removed during a transfer.
- Fix several cases where a broken device could cause an infinite loop
while we wait for a register to update.
Drivers:
- at91-mci: Remove obsolete driver, atmel-mci handles these devices now.
- sdhci-dove: Allow using GPIOs for card-detect notifications.
- sdhci-esdhc: Fix for recovering from ADMA errors on broken silicon.
- sdhci-s3c: Add pinctrl support.
- wmt-sdmmc: New driver for WonderMedia SD/MMC controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=oSX3
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.8:
Core:
- Expose access to the eMMC RPMB ("Replay Protected Memory Block")
area by extending the existing mmc_block ioctl.
- Add SDIO powered-suspend DT properties to the core MMC DT binding.
- Add no-1-8-v DT flag for boards where the SD controller reports
that it supports 1.8V but the board itself has no way to switch to
1.8V.
- More work on switching to 1.8V UHS support using a vqmmc regulator.
- Fix up a case where the slot-gpio helper may fail to reset the host
controller properly if a card was removed during a transfer.
- Fix several cases where a broken device could cause an infinite
loop while we wait for a register to update.
Drivers:
- at91-mci: Remove obsolete driver, atmel-mci handles these devices
now.
- sdhci-dove: Allow using GPIOs for card-detect notifications.
- sdhci-esdhc: Fix for recovering from ADMA errors on broken silicon.
- sdhci-s3c: Add pinctrl support.
- wmt-sdmmc: New driver for WonderMedia SD/MMC controllers."
* tag 'mmc-updates-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (65 commits)
mmc: sdhci: implement the .card_event() method
mmc: extend the slot-gpio card-detection to use host's .card_event() method
mmc: add a card-event host operation
mmc: sdhci-s3c: Fix compilation warning
mmc: sdhci-pci: Enable SDHCI_CAN_DO_HISPD for Ricoh SDHCI controller
mmc: sdhci-dove: allow GPIOs to be used for card detection on Dove
mmc: sdhci-dove: use two-stage initialization for sdhci-pltfm
mmc: sdhci-dove: use devm_clk_get()
mmc: eSDHC: Recover from ADMA errors
mmc: dw_mmc: remove duplicated buswidth code
mmc: dw_mmc: relocate where dw_mci_setup_bus() is called from
mmc: Limit MMC speed to 52MHz if not HS200
mmc: dw_mmc: use devres functions in dw_mmc
mmc: sh_mmcif: remove unneeded clock connection ID
mmc: sh_mobile_sdhi: remove unneeded clock connection ID
mmc: sh_mobile_sdhi: fix clock frequency printing
mmc: Remove redundant null check before kfree in bus.c
mmc: Remove redundant null check before kfree in sdio_bus.c
mmc: sdhci-imx-esdhc: use more devm_* functions
mmc: dt: add no-1-8-v device tree flag
...
HSMMC IP on AM33xx need a special setting to handle High-speed cards.
Other platforms like TI81xx, OMAP4 may need this as-well. This depends
on the HSMMC IP timing closure done for the high speed cards.
From AM335x TRM (SPRUH73F - 18.3.12 Output Signals Generation):
The MMC/SD/SDIO output signals can be driven on either falling edge or
rising edge depending on the SD_HCTL[2] HSPE bit. This feature allows
to reach better timing performance, and thus to increase data transfer
frequency.
There are few pre-requisites for enabling the HSPE bit
- Controller should support High-Speed-Enable Bit and
- Controller should not be using DDR Mode and
- Controller should advertise that it supports High Speed in
capabilities register and
- MMC/SD clock coming out of controller > 25MHz
Signed-off-by: Hebbar, Gururaja <gururaja.hebbar@ti.com>
Signed-off-by: Venkatraman S <svenkatr@ti.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=w+UN
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/pm2
From Tony Lindgren:
Remaining patches to allow omap2+ to build with multiplatform
enabled. Unfortunately the DMA header patch had to be redone
to avoid adding new multiplatform specific include paths, the
other patches are just trivial compile fixes.
Note that this does not yet contain the necessary Kconfig
changes as we are still waiting for some drivers to get
fixed up first.
* tag 'tags/omap-for-v3.8/cleanup-multiplatform-no-clock-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: Move plat-omap/dma-omap.h to include/linux/omap-dma.h
ASoC: OMAP: mcbsp fixes for enabling ARM multiplatform support
watchdog: OMAP: fixup for ARM multiplatform support
Conflicts due to surrounding changes in:
arch/arm/mach-omap2/omap_hwmod_2420_data.c
arch/arm/mach-omap2/omap_hwmod_2430_data.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yFcc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/headers
From Tony Lindgren:
Move most of remaining omap iommu code to drivers/iommu.
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
* tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
Conflicts due to surrounding changes in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
drivers/media/platform/omap3isp/ispvideo.c
Signed-off-by: Olof Johansson <olof@lixom.net>
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=yFcc
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren:
Move most of remaining omap iommu code to drivers/iommu.
This is needed for the multiplatform kernels as the plat
and mach headers cannot be included.
These changes were agreed to be merged via the arm-soc
tree by Joerg and Ohad as these will cause some merge
conflicts with the other related clean-up branches.
So omap-for-v3.8/cleanup-headers-iommu should be added
as one of the depends branches for arm-soc.
* tag 'omap-for-v3.8/cleanup-headers-iommu-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Move iommu/iovmm headers to platform_data
ARM: OMAP2+: Make some definitions local
ARM: OMAP2+: Move iommu2 to drivers/iommu/omap-iommu2.c
ARM: OMAP2+: Move plat/iovmm.h to include/linux/omap-iommu.h
ARM: OMAP2+: Move iopgtable header to drivers/iommu/
ARM: OMAP: Merge iommu2.h into iommu.h
Conflicts due to surrounding changes fixed up in:
arch/arm/mach-omap2/omap_hwmod_44xx_data.c
drivers/media/platform/omap3isp/ispvideo.c
Signed-off-by: Olof Johansson <olof@lixom.net>
Based on earlier discussions[1] we attempted to find a suitable
location for the omap DMA header in commit 2b6c4e73 (ARM: OMAP:
DMA: Move plat/dma.h to plat-omap/dma-omap.h) until the conversion
to dmaengine is complete.
Unfortunately that was before I was able to try to test compile
of the ARM multiplatform builds for omap2+, and the end result
was not very good.
So I'm creating yet another all over the place patch to cut the
last dependency for building omap2+ for ARM multiplatform. After
this, we have finally removed the driver dependencies to the
arch/arm code, except for few drivers that are being worked on.
The other option was to make the <plat-omap/dma-omap.h> path
to work, but we'd have to add some new header directory to for
multiplatform builds.
Or we would have to manually include arch/arm/plat-omap/include
again from arch/arm/Makefile for omap2+.
Neither of these alternatives sound appealing as they will
likely lead addition of various other headers exposed to the
drivers, which we want to avoid for the multiplatform kernels.
Since we already have a minimal include/linux/omap-dma.h,
let's just use that instead and add a note to it to not
use the custom omap DMA functions any longer where possible.
Note that converting omap DMA to dmaengine depends on
dmaengine supporting automatically incrementing the FIFO
address at the device end, and converting all the remaining
legacy drivers. So it's going to be few more merge windows.
[1] https://patchwork.kernel.org/patch/1519591/#
cc: Russell King <linux@arm.linux.org.uk>
cc: Kevin Hilman <khilman@ti.com>
cc: "Benoît Cousson" <b-cousson@ti.com>
cc: Herbert Xu <herbert@gondor.apana.org.au>
cc: "David S. Miller" <davem@davemloft.net>
cc: Vinod Koul <vinod.koul@intel.com>
cc: Dan Williams <djbw@fb.com>
cc: Mauro Carvalho Chehab <mchehab@infradead.org>
cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
cc: David Woodhouse <dwmw2@infradead.org>
cc: Kyungmin Park <kyungmin.park@samsung.com>
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
cc: Hans Verkuil <hans.verkuil@cisco.com>
cc: Vaibhav Hiremath <hvaibhav@ti.com>
cc: Lokesh Vutla <lokeshvutla@ti.com>
cc: Rusty Russell <rusty@rustcorp.com.au>
cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
cc: Afzal Mohammed <afzal@ti.com>
cc: linux-crypto@vger.kernel.org
cc: linux-media@vger.kernel.org
cc: linux-mtd@lists.infradead.org
cc: linux-usb@vger.kernel.org
cc: linux-fbdev@vger.kernel.org
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=JSAM
-----END PGP SIGNATURE-----
Merge tag 'tags/omap-for-v3.8/devel-prcm-signed' into omap-for-v3.8/cleanup-headers-prepare-multiplatform-v3
omap prcm changes via Paul Walmsley <paul@pwsan.com>:
Some miscellaneous OMAP hwmod changes for 3.8, along with a PRM
change needed for one of the hwmod patches to function.
Basic test logs for this branch on top of Tony's
omap-for-v3.8/clock branch at commit
558a0780b0 are here:
http://www.pwsan.com/omap/testlogs/hwmod_devel_a_3.8/20121121161522/
However, omap-for-v3.8/clock at 558a0780 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_hwmod_devel_a_3.8/20121121162719/
which indicate that the series tests cleanly.
Conflicts:
arch/arm/mach-omap2/cm33xx.c
arch/arm/mach-omap2/io.c
arch/arm/mach-omap2/prm_common.c
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=XZ+L
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
Timer clean-up to get us closer to moving timer code to drivers,
and to get rid of CONFIG_OMAP_32K_TIMER and rely on the board
or devicetree provided timer configuration.
Note that these changes are on top of the recent timer fixes.
By Jon Hunter (32) and others
via Tony Lindgren
* tag 'omap-for-v3.8/cleanup-timer-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (71 commits)
ARM: OMAP3: cm-t3517: use GPTIMER for system clock
ARM: OMAP2+: timer: remove CONFIG_OMAP_32K_TIMER
ARM: OMAP2+: Fix compiler warning for 32k timer
ARM: OMAP: Remove unnecessary inclusion of dmtimer.h
ARM: OMAP: Add platform data header for DMTIMERs
ARM: OMAP: Remove unnecessary omap_dm_timer structure declaration
ARM: OMAP2+: Remove unnecessary local variable in timer code
ARM: OMAP: Don't store timers physical address
ARM: OMAP: Define omap_dm_timer_prepare function as static
ARM: OMAP: Clean-up dmtimer reset code
ARM: OMAP: Remove __omap_dm_timer_set_source function
ARM: OMAP: Remove unnecessary call to clk_get()
ARM: OMAP: Add dmtimer interrupt disable function
ARM: OMAP: Fix spurious interrupts when using timer match feature
ARM: OMAP: Don't restore DMTIMER interrupt status register
ARM: OMAP: Don't restore of DMTIMER TISTAT register
ARM: OMAP: Fix dmtimer reset for timer1
ARM: OMAP2+: Don't use __omap_dm_timer_reset()
ARM: OMAP2/3: Define HWMOD software reset status for DMTIMERs
ARM: OMAP3: Correct HWMOD DMTIMER SYSC register declarations
...
Change/change conflict in arch/arm/mach-omap2/board-cm-t3517.c.
Signed-off-by: Olof Johansson <olof@lixom.net>
Pull i2c fixes from Wolfram Sang:
"Bugfixes for the i2c subsystem.
Except for a few one-liners, there is mainly one revert because of an
overlooked dependency. Since there is no linux-next at the moment, I
did some extra testing, and all was fine for me."
* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
i2c: mxs: Handle i2c DMA failure properly
i2c: s3c2410: Fix code to free gpios
i2c: omap: ensure writes to dev->buf_len are ordered
Revert "ARM: OMAP: convert I2C driver to PM QoS for MPU latency constraints"
i2c: at91: fix SMBus quick command
CONFIG_OMAP_32K_TIMER is kind of standing on the single zImage way.
Make OMAP2+ timer code independant from the CONFIG_OMAP_32K_TIMER
setting.
To remove the dependancy, several conversions/additions had to be done:
1) Timer initialization functions are named by the platform
name and the clock source in use.
This also makes it possible to define and use the GPTIMER as the
clock source instead of the 32K timer on platforms that do not have
the 32K timer ip block or the 32K timer is not wired on the board.
Currently, the the timer is chosen in the machine_desc structure on
per board basis. Later, DT should be used to choose the timer.
2) Settings under the CONFIG_OMAP_32K_TIMER option are used as defaults
and those under !CONFIG_OMAP_32K_TIMER are removed.
This removes the CONFIG_OMAP_32K_TIMER on OMAP2+ timer code.
3) Since we have all the timers defined inside machine_desc structure
and we no longer need the fallback to gp_timer clock source in case
32k_timer clock source is unavailable (namely on AM33xx), we no
longer need the #ifdef around omap2_sync32k_clocksource_init()
function. Remove the #ifdef CONFIG_OMAP_32K_TIMER around the
omap2_sync32k_clocksource_init() function.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Jon Hunter <jon-hunter@ti.com>
Move iommu/iovmm headers from plat/ to platform_data/ as part of the
single zImage work.
Partially based on an earlier version by Ido Yariv <ido@wizery.com>.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This file should not be in arch/arm. Move it to drivers/iommu
to allow making most of the header local to drivers/iommu.
This is needed as we are removing plat and mach includes
from drivers for ARM common zImage support.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Cc: linux-media@vger.kernel.org
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like the iommu framework does not have generic functions
exported for all the needs yet. The hardware specific functions
are defined in files like intel-iommu.h and amd-iommu.h. Follow
the same standard for omap-iommu.h.
This is needed because we are removing plat and mach includes
for ARM common zImage support. Further work should continue
in the iommu framework context as only pure platform data will
be communicated from arch/arm/*omap*/* code to the iommu
framework.
Cc: Ido Yariv <ido@wizery.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Cc: linux-media@vger.kernel.org
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The iopgtable header file is only used by the iommu & iovmm drivers, so
move it to drivers/iommu/, as part of the single zImage effort.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
[tony@atomide.com: updated to be earlier in the series]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since iommu is not supported on OMAP1 and will not likely to ever be
supported, merge plat/iommu2.h into iommu.h so only one file would have
to move to platform_data/ as part of the single zImage effort.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Omar Ramirez Luna <omar.luna@linaro.org>
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Joerg Roedel <joro@8bytes.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove unnecessary declaration of structure omap_dm_timer from dmtimer.h and
move the actual declaration of structure omap_dm_timer towards top of dmtimer.h
to avoid any compilation errors.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The OMAP2+ system timer code stores the physical address of the timer
but never uses it. Remove this and clean-up the code by removing the
local variable "size" and changing the names of the local variables
mem_rsrc and irq_rsrc to mem and irq, respectively.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
The omap_dm_timer_prepare function is a local function only used in the
dmtimer.c file. Therefore, make this a static function and remove its
declaration from the dmtimer.h file.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Only OMAP1 devices use the omap_dm_timer_reset() and so require the
omap_dm_timer_wait_for_reset() and __omap_dm_timer_reset() functions.
Therefore combine these into a single function called omap_dm_timer_reset()
and simplify the code.
The omap_dm_timer_reset() function is now the only place that is using the
omap_dm_timer structure member "sys_stat". Therefore, remove this member and
just use the register offset definition to simplify and clean-up the code. The
TISTAT register is only present on revision 1 timers and so check for this in
the omap_dm_timer_reset() function.
Please note that for OMAP1 devices, the TIOCP_CFG register does not have the
clock-activity field and so when we reset the timer for an OMAP1 device we
only need to configure the idle-mode field in the TIOCP_CFG register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Conflicts:
drivers/video/omap2/dss/Kconfig
drivers/video/omap2/omapfb/omapfb-ioctl.c
drivers/video/omap2/omapfb/omapfb-main.c
Merge changes to make omapfb use common dma_alloc, and remove omap's
custom vram allocator.
Second set of OMAP PRCM cleanups for 3.8.
These patches remove the use of omap_prcm_get_reset_sources() from the
OMAP watchdog driver, and remove mach-omap2/prcm.c and
plat-omap/include/plat/prcm.h.
Basic test logs for this branch on top of Tony's cleanup-prcm branch
at commit 7fc54fd308 are here:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_b_3.8/20121108151646/
However, cleanup-prcm at 7fc54fd3 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_prcm_cleanup_b_3.8/20121108151930/
which indicate that the series tests cleanly.
This second pull request updates one of the patches which broke
with rmk's allnoconfigs, and also updates the tag description to
indicate that 7fc54fd3 is building cleanly here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQoY0GAAoJEBvUPslcq6Vza0MQAI0idVoOclIHCC63tpc58YWA
BpD5OLg4yRu0RUFS1CI/Fq5d+9PfYUspgaWja3TTgUy0EHRDVUUFRaxJdpWdl2NF
gX7BCuhnQenznTbCE80nEmxvsh7U/dfvs+JYUK2PriypU61f1+TnSu9ZxTRvDJOx
vbo1cfsioVcLfnBPSDSQVJ1fufbafklpeQkDNeRI8UDsCVeXwnxhNsXB3utoJMf0
5gaDaCdRBoimkLnAaLi41OnHYC7IbNCnl/VX0i/xffROsINfL7LDkBPfUOnR5vle
jTCV49UEB/P5ekk2cvKKj8IOQZdimiCppWMLit6DObX7LbltTKuXx6T0PclgxQ14
hhav5O+f8NYA4yDAY/xxPlTvShMr8rQcYV6pg1G1OgD+dcq7cbbWNJAvbUJ03hH8
dqZ+ypLYkazb3Mm5XtpFr47gkoaFnCQbgZLXpjJ8+L01aGNrF2L6aE789So1N81+
X1s0ENjRxzDLNcqwxqhcoph0YQe7GlyiviYb7ev25MTSC3/TjrupTViZbKocZmLt
Ad9m4SOktbHthAw0jdA48vOmPiSvmYzFiqzMhz/ryeNbyyV6rRxe5w4JUjPzHPxc
U7NraSGIAzpqM3EKEp7Rb0yOfh6sGzML/FH9bS25+Rv37yKW0huc6ENIRgatZpY2
blLzsxaKfQgLeqKT82mj
=tS2z
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.8/cleanup-prcm-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup
From Tony Lindgren <tony@atomide.com>:
More PRCM cleanups via Paul Walmsley <paul@pwsan.com>:
Second set of OMAP PRCM cleanups for 3.8.
These patches remove the use of omap_prcm_get_reset_sources() from the
OMAP watchdog driver, and remove mach-omap2/prcm.c and
plat-omap/include/plat/prcm.h.
Basic test logs for this branch on top of Tony's cleanup-prcm branch
at commit 7fc54fd308 are here:
http://www.pwsan.com/omap/testlogs/prcm_cleanup_b_3.8/20121108151646/
However, cleanup-prcm at 7fc54fd3 does not include some fixes
that are needed for a successful test. With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:
http://www.pwsan.com/omap/testlogs/TEST_prcm_cleanup_b_3.8/20121108151930/
which indicate that the series tests cleanly.
This second pull request updates one of the patches which broke
with rmk's allnoconfigs, and also updates the tag description to
indicate that 7fc54fd3 is building cleanly here.
* tag 'omap-for-v3.8/cleanup-prcm-part2-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (27 commits)
ARM: OMAP2: Fix compillation error in cm_common
ARM: OMAP2+: PRCM: remove obsolete prcm.[ch]
ARM: OMAP2+: hwmod: call to _omap4_disable_module() should use the SoC-specific call
ARM: OMAP2+: PRCM: consolidate PRCM-related timeout macros
ARM: OMAP2+: PRCM: split and relocate the PRM/CM globals setup
ARM: OMAP2+: PRCM: remove omap2_cm_wait_idlest()
ARM: OMAP2+: CM/clock: convert _omap2_module_wait_ready() to use SoC-independent CM functions
ARM: OMAP2xxx: APLL/CM: convert to use omap2_cm_wait_module_ready()
ARM: OMAP2+: board files: use SoC-specific system restart functions
ARM: OMAP2+: PRCM: create SoC-specific chip restart functions
ARM: OMAP2xxx: clock: move virt_prcm_set code into clkt2xxx_virt_prcm_set.c
ARM: OMAP2xxx: clock: remove global 'dclk' variable
ARM: OMAP2/3: PRM: add SoC reset functions (using the CORE DPLL method)
ARM: OMAP2+: common: remove mach-omap2/common.c globals and map_common_io code
ARM: OMAP2+: PRCM: remove omap_prcm_get_reset_sources()
watchdog: OMAP: use standard GETBOOTSTATUS interface; use platform_data fn ptr
ARM: OMAP2+: WDT: move init; add read_reset_sources pdata function pointer
ARM: OMAP1: CGRM: fix omap1_get_reset_sources() return type
ARM: OMAP2+: PRM: create PRM reset source API for the watchdog timer driver
ARM: OMAP1: create read_reset_sources() function (for initial use by watchdog)
...
Conflicts:
arch/arm/mach-omap2/cm33xx.c
arch/arm/mach-omap2/io.c
arch/arm/mach-omap2/prm_common.c
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
OMAP specific vram allocator is no longer used, and we can remove init
call to the vram allocator.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Use DMA_BIT_MASK() for fb's coherent_dma_mask for clarity.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The __omap_dm_timer_set_source() function is only used by the system timer
(clock-events and clock-source) code for OMAP2+ devices. Therefore, we can
remove this code from the dmtimer driver and move it to the system timer
code for OMAP2+ devices.
The current __omap_dm_timer_set_source() function calls clk_disable() before
calling clk_set_parent() and clk_enable() afterwards. We can avoid these calls
to clk_disable/enable by moving the calls to omap_hwmod_setup_one() and
omap_hwmod_enable() to after the call to clk_set_parent() in
omap_dm_timer_init_one().
The function omap_hwmod_setup_one() will enable the timers functional clock
and therefore increment the use-count of the functional clock to 1.
clk_set_parent() will fail if the use-count is not 0 when called. Hence, if
omap_hwmod_setup_one() is called before clk_set_parent(), we will need to call
clk_disable() before calling clk_set_parent() to decrement the use-count.
Hence, avoid these extra calls to disable and enable the functional clock by
moving the calls to omap_hwmod_setup_one() and omap_hwmod_enable() to after
clk_set_parent().
We can also remove the delay from the __omap_dm_timer_set_source() function
because enabling the clock will now be handled via the HWMOD framework by
calling omap_hwmod_setup_one(). Therefore, by moving the calls to
omap_hwmod_setup_one() and omap_hwmod_enable() to after the call to
clk_set_parent(), we can simply replace __omap_dm_timer_set_source() with
clk_set_parent().
It should be safe to move these hwmod calls to later in the
omap_dm_timer_init_one() because other calls to the hwmod layer that occur
before are just requesting resource information.
Testing includes boot testing on OMAP2420 H4, OMAP3430 SDP and OMAP4430 Blaze
with the following configurations:
1. CONFIG_OMAP_32K_TIMER=y
2. CONFIG_OMAP_32K_TIMER=y and boot parameter "clocksource=gp_timer"
3. CONFIG_OMAP_32K_TIMER not set
4. CONFIG_OMAP_32K_TIMER not set and boot parameter "clocksource=gp_timer"
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Whenever we call the function omap_dm_timer_set_source() to set the clock
source of a dmtimer we look-up the dmtimer functional clock source by
calling clk_get(). This is not necessary because on requesting a dmtimer
we look-up the functional clock source and store it in the omap_dm_timer
structure. So instead of looking up the clock again used the clock handle
that stored in the omap_dm_timer structure.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The OMAP dmtimer driver does not currently have a function to disable the
timer interrupts. For some timer instances the timer interrupt enable
function can be used to disable the interrupts because the same interrupt
enable register is used to disable interrupts. However, some timer instances
have separate interrupt enable/disable registers and so this will not work.
Therefore, add a dedicated function to disable interrupts.
This change is required for OMAP4+ devices. For OMAP4, all timers apart from 1,
2 and 10 need this function and for OMAP5 all timers need this function.
Please note that the interrupt disable function has been written so that it
can be used by all OMAP devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The OMAP DMTIMERs can generate an interrupt when the timer counter value
matches the value stored in the timer's match register. When using this
feature spurious interrupts were seen, because the compare logic is being
enabled before the match value is loaded and according to the documentation
the match value must be loaded before the compare logic is enable.
The reset value for the timer counter and match registers is 0 and hence,
by enabling the compare logic before the actual match value is loaded a
spurious interrupt can be generated as the reset values match.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Restoring the timer interrupt status is not possible because writing a 1 to any
bit in the register clears that bit if set and writing a 0 has no affect.
Furthermore, if an interrupt is pending when someone attempts to disable a
timer, the timer will fail to transition to the idle state and hence it's
context will not be lost. Users should take care to service all interrupts
before disabling the timer.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The timer TISTAT register is a read-only register and therefore restoring the
context is not needed. Furthermore, the context of TISTAT is never saved
anywhere in the current code. The TISTAT register is read-only for all OMAP
devices from OMAP1 to OMAP4. OMAP5 timers no longer have this register.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
In commit e32f7ec2 (ARM: OMAP: Fix 32 kHz timer and modify GP timer to use GPT1)
a fix was added to prevent timer1 being reset in the function
omap_dm_timer_reset() because timer1 was being used as the system timer for
OMAP2 devices. Although timer1 is still used by most OMAP2+ devices as a system
timer, the function omap_dm_timer_reset() is now only being called for OMAP1
devices and OMAP1 does not use timer1 as a system timer. Therefore, remove the
check in omap_dm_timer_reset() so that timer1 is reset for OMAP1 devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Currently the dmtimer posted mode is being enabled when the function
omap_dm_timer_enable_posted() is called. This function is only being called
for OMAP1 timers and OMAP2+ timers that are being used as system timers. Hence,
for OMAP2+ timers that are NOT being used as a system timer, posted mode is
not enabled but the "timer->posted" variable is still set (incorrectly) in
the omap_dm_timer_prepare() function.
This is a regression introduced by commit 3392cdd3 (ARM: OMAP: dmtimer:
switch-over to platform device driver) which was before the
omap_dm_timer_enable_posted() function was introduced. Although this is a
regression from the original code it only impacts performance and so is not
needed for stable.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Errata Titles:
i103: Delay needed to read some GP timer, WD timer and sync timer
registers after wakeup (OMAP3/4)
i767: Delay needed to read some GP timer registers after wakeup (OMAP5)
Description (i103/i767):
If a General Purpose Timer (GPTimer) is in posted mode
(TSICR [2].POSTED=1), due to internal resynchronizations, values read in
TCRR, TCAR1 and TCAR2 registers right after the timer interface clock
(L4) goes from stopped to active may not return the expected values. The
most common event leading to this situation occurs upon wake up from
idle.
GPTimer non-posted synchronization mode is not impacted by this
limitation.
Workarounds:
1). Disable posted mode
2). Use static dependency between timer clock domain and MPUSS clock
domain
3). Use no-idle mode when the timer is active
Workarounds #2 and #3 are not pratical from a power standpoint and so
workaround #1 has been implemented. Disabling posted mode adds some CPU
overhead for configuring and reading the timers as the CPU has to wait
for accesses to be re-synchronised within the timer. However, disabling
posted mode guarantees correct operation.
Please note that it is safe to use posted mode for timers if the counter
(TCRR) and capture (TCARx) registers will never be read. An example of
this is the clock-event system timer. This is used by the kernel to
schedule events however, the timers counter is never read and capture
registers are not used. Given that the kernel configures this timer
often yet never reads the counter register it is safe to enable posted
mode in this case. Hence, for the timer used for kernel clock-events,
posted mode is enabled by overriding the errata for devices that are
impacted by this defect.
For drivers using the timers that do not read the counter or capture
registers and wish to use posted mode, can override the errata and
enable posted mode by making the following function calls.
__omap_dm_timer_override_errata(timer, OMAP_TIMER_ERRATA_I103_I767);
__omap_dm_timer_enable_posted(timer);
Both dmtimers and watchdogs are impacted by this defect this patch only
implements the workaround for the dmtimer. Currently the watchdog driver
does not read the counter register and so no workaround is necessary.
Posted mode will be disabled for all OMAP2+ devices (including AM33xx)
using a GP timer as a clock-source timer to guarantee correct operation.
This is not necessary for OMAP24xx devices but the default clock-source
timer for OMAP24xx devices is the 32k-sync timer and not the GP timer
and so should not have any impact. This should be re-visited for future
devices if this errata is fixed.
Confirmed with Vaibhav Hiremath that this bug also impacts AM33xx
devices.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
For OMAP2+ devices, when using DMTIMERs for system timers (clock-events and
clock-source) the posted mode configuration of the timers is used. To allow
the compiler to optimise the functions for configuring and reading the system
timers, the posted flag variable is hard-coded with the value 1. To make it
clear that posted mode is being used add some definitions so that it is more
readable.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=c5hx
-----END PGP SIGNATURE-----
Merge tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91 into next/headers
From Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>:
arm: at91: mach header cleanup
This first patch serie start the cleanup of the header in mach
by moving all the platform data to include/linux/platform_data
and move the board header and drivers header next to them
* tag 'for-3.8-at91_header_clean' of git://github.com/at91linux/linux-at91:
arm: at91: move at91rm9200 rtc header in drivers/rtc
arm: at91: move reset controller header to arm/arm/mach-at91
arm: at91: move pit define to the driver
arm: at91: move at91_shdwc.h to arch/arm/mach-at91
arm: at91: move board header to arch/arm/mach-at91
arn: at91: move at91_tc.h to arch/arm/mach-at91
arm: at91 move at91_aic.h to arch/arm/mach-at91
arm: at91 move board.h to arch/arm/mach-at91
arm: at91: move platfarm_data to include/linux/platform_data/atmel.h
arm: at91: drop machine defconfig
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The debug-leds driver should not rely on hard coded macro for
the iomem size but use the resource size instead.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/mach-omap2/prcm.c and arch/arm/plat-omap/include/plat/prcm.h
are now completely unused and can be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Split omap2_set_globals_prcm() into PRM, CM, and PRCM_MPU variants, since
these are all separate IP blocks. This should make it easier to move the
PRM, CM, PRCM_MPU code into drivers/ in future patchsets.
At this point arch/arm/plat-omap/include/plat/prcm.h is empty; a
subsequent patch will remove it, and remove the #include from all the
files that #include it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Now that all users of mach-omap2/omap2_cm_wait_idlest() have been removed,
delete the function and its supporting macros and prototypes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Get rid of the mach-omap2/common.c globals by moving the global
initialization for IP block addresses that must occur early into
mach-omap2/io.c. In the process, remove the *_map_common_io*() and
SoC-specific *set_globals* functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
omap_prcm_get_reset_sources() is now unused; so, remove it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
The only thing omap_init_consistent_dma_size() does is increase the
consistent DMA size if CONFIG_FB_OMAP_CONSISTENT_DMA_SIZE is defined.
Increasing the consistent DMA size should no longer be needed with CMA
in place.
This patch removes omap_init_consistent_dma_size() and also
arch/arm/mach-omap2/io.c:omap_common_init_early() which becomes an empty
function.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[tony@atomide.com: updated for moved dma.h]
Signed-off-by: Tony Lindgren <tony@atomide.com>
struct uart_omap_port and struct uart_omap_dma, and associated
definitions are private to the driver, so there's no point them sitting
in an include file under arch/arm. Move them into the driver itself.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Now mach/hardware.h is empty for omap2+ and can be
removed except for plat-omap/dmtimer.c for omap1.
Also the include of mach/irqs.h can now be removed
for shared plat-omap/i2c.c as it's no longer needed.
Signed-off-by: Tony Lindgren <tony@atomide.com>
In order to add device-tree support to the timer driver the following changes
were made ...
1. Allocate system timers (used for clock-events and clock-source) based upon
timer properties rather than using an hard-coded timer instance ID. To allow
this a new helper function called omap_dmtimer_find_by_property() has been
added for finding a timer with the particular properties in the device-tree
blob. Please note that this is an internal helper function for system timers
only to find a timer in the device-tree blob. This cannot be used by device
drivers, another API has been added for that (see below). Timers that are
allocated for system timers are dynamically disabled at boot time by adding
a status property with the value "disabled" to the timer's device-tree node.
Please note that when allocating system timers we now pass a timer ID and
timer property. The timer ID is only be used for allocating a timer when
booting without device-tree. Once device-tree migration is complete, all
the timer ID references will be removed.
2. System timer resources (memory and interrupts) are directly obtained from
the device-tree timer node when booting with device-tree, so that system
timers are no longer reliant upon the OMAP HWMOD framework to provide these
resources.
3. If DT blob is present, then let device-tree create the timer devices
dynamically.
4. When device-tree is present the "id" field in the platform_device structure
(pdev->id) is initialised to -1 and hence cannot be used to identify a timer
instance. Due to this the following changes were made ...
a). The API omap_dm_timer_request_specific() is not supported when using
device-tree, because it uses the device ID to request a specific timer.
This function will return an error if called when device-tree is present.
Users of this API should use omap_dm_timer_request_by_cap() instead.
b). When removing the DMTIMER driver, the timer "id" was used to identify the
timer instance. The remove function has been modified to use the device
name instead of the "id".
5. When device-tree is present the platform_data structure will be NULL and so
check for this.
6. The OMAP timer device tree binding has the following optional parameters ...
a). ti,timer-alwon --> Timer is in an always-on power domain
b). ti,timer-dsp --> Timer can generate an interrupt to the on-chip DSP
c). ti,timer-pwm --> Timer can generate a PWM output
d). ti,timer-secure --> Timer is reserved on a secure OMAP device
Search for the above parameters and set the appropriate timer attribute
flags.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Currently OMAP timers can be requested by requesting any available or by a
numerical device ID. If a specific timer is required because it has a particular
capability, such as can interrupt the on-chip DSP in addition to the ARM CPU,
then the user needs to know the device ID of the timer with this feature.
Therefore, add a new API called omap_dm_timer_request_by_cap() that allows
drivers to request a timer by capability.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* code:
http://www.spinics.net/lists/linux-omap/msg80520.html
Fix includes for fpga.h by making fpga.h local
to mach-omap1. The common code in plat-omap just
needs to know the struct h2p2_dbg_fpga, which can
be local to debug-leds.c.
This also fixes the braindead <../*.h> style includes
that got accidentally added with search and replace
during the cleanup.
Signed-off-by: Tony Lindgren <tony@atomide.com>
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* code:
http://www.spinics.net/lists/linux-omap/msg80520.html
Note that eventually when the omap1 specific drivers
are fixed to not use cpu_is_omap macros and not depend
on mach/hardware.h, this patch can be reverted and these
headers can be local. But since just fixing the drivers for
omap2+ is already a big enough hassle, let's deal
with that properly first.
[tony@atomide.com: also drop unused include for ispvideo.c]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This code will be eventually in drivers, and for the
code in the drivers we don't want to have any cpu_is_omap
usage. Those macros should be private to arch/arm/mach-omap1
and arch/arm/mach-omap2.
To fix this, let's move the define for dma_omap2plus()
to dma-omap.h, and use the existing dma_attr passed in
the platform_data as the revision registers are what they
are.
Note that we can now also remove the relative includes
introduced by the recent clean-up patches.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Vinod Koul <vinod.koul@intel.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* shared code:
http://www.spinics.net/lists/linux-omap/msg80520.html
Let's add plat/debug-devices.h for debug_card_init()
to fix the relative includes.
Note that drivers must not use this header as it will
break build for omap2+ CONFIG_MULTIPLATFORM builds.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the prototypes in plat-omap/common.h are not
common to omap1 and omap2+, they are local to omap2+
and should not be in plat-omap/common.h.
The only shared function prototype in this file is
omap_init_clocksource_32k(), let's put that into
counter-32k.h.
Note that the new plat/counter-32k.h must not be
included from drivers, that will break omap2+ build
for CONFIG_MULTIPLATFORM.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This code should be private to mach-omap2.
The only use for it in for omap1 has been in dmtimer.c
to check for context loss. However, omap1 does not
lose context during idle, so the code is not needed.
Further, omap1 timer has OMAP_TIMER_ALWON set, so omap1
was not hitting omap_pm_get_dev_context_loss_count()
test.
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* shared code:
http://www.spinics.net/lists/linux-omap/msg80520.html
To fix this for the shared i2c.h, let's re-introduce
a minimal plat/i2c.h.
Note that drivers must not use this header as it will
break build for omap2+ CONFIG_MULTIPLATFORM builds.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The common code should not have any omap1 or omap2+
specific code, and should not need to call the cpu_is_omap
macros.
The only remaining user for cpu_is_omap macros is
omap_i2c_nr_ports(). Let's make those checks in
the omap specific implementation of omap_i2c_add_bus()
instead in order to remove cpu_is_omap usage from
the common code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Let's make the omap2+ specific parts private to mach-omap2.
This leaves just a minimal shared code into plat-omap like
it should be.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the defines are specific to omap1 and omap2+,
and should be in the local headers. Only minimal function
prototypes need to be shared.
As discussed on linux-arm-kernel, we want to avoid
relative includes for the arch/arm/*omap* shared code:
http://www.spinics.net/lists/linux-omap/msg80520.html
So this patch re-adds a minimal plat/sram.h.
The new plat/sram.h must not be included from drivers,
that will break build for omap2+ CONFIG_MULTIPLATFORM.
Note that this patch temporarily adds two more
relative includes; Those will be removed in the
following patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add HWMOD_EXT_OPT_MAIN_CLK flag to indicate that this IP block is
dependent on an off-chip functional clock that is not guaranteed to be
present during initialization. IP blocks marked with this flag are
left in the INITIALIZED state during kernel init.
This is a workaround for a hardware problem. It should be possible to
guarantee that at least one clock source will be present and active
for any IP block's main functional clock. This ensures that the hwmod
code can enable and reset the IP block. Resetting the IP block during
kernel init prevents any bogus bootloader, ROM code, or previous OS
configuration from affecting the kernel. Hopefully a clock
multiplexer can be added on future SoCs.
N.B., at some point in the future, it should be possible to query the
clock framework for this type of information. Then this flag should
no longer be needed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Jon Hunter