Split some existing initialization code into a separate function for use
by EEH next. No functional changes.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the larger flash memories on newer boards:
- get the size and number of sectors by probing the flash
- writes and erases can take longer, adjust the timeouts for these operations
- the FW image can be at different locations depending on flash size,
find its location dynamically as well.
Signed-off-by: Dimitris Michailidis <dm@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For certain set of register, base window addresses are not defined.
In such cases window should not set.
Return with error for such cases to avoid NMI.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race between netif_stop_queue and netif_stopped_queue
check. So check once again if buffers are available to avoid race.
With above logic we can also get rid of tx lock in process_cmd_ring.
Signed-off-by: Rajesh K Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Earlier all poll routine can process rx and tx, But now
one poll routine to process rx + tx and other for rx only.
Last msix vector will be used for separate tx interrupt.
o This is supported from fw version 4.4.2.
o Bump version 5.0.5
Signed-off-by: Sony Chacko <schacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Remove extra printing of mac address
o This driver also supports NIC only Qlogic adapters.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During device soft reset, don't halt every device block.
Access to some blocks is required during recovery.
Signed-off-by: Sucheta Chakraborty <sucheta@dut4145.unminc.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed the driver version number to 5.0.4
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver was not detecting the presence of NIC partitioning capability of the
firmware properly. Now, it checks the eswitch set bit in the FW capabilities
register and accordingly sets the driver mode as NPAR capable or not.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only report PHY error frames for ANI on chipsets which do not have PHY error
counters in hardware.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reviewed RX descriptor functions against the HAL sources. Some minor changes:
- check size before making changes to the descriptor
- whitespace
- add comments about 5210 timestamps. this needs to be adressed later!
- FIFO overrun error only available on 5210
- rs_phyerr should not be OR'ed
- clear the whole ath5k_rx_status structure before using, instead of
zeroing specific fields.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are some differences between 5210 and 5211 descriptors which we did not
take into account before.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update 5210 frame types to match the HAL. We have to apply the same bitshift to
the constants as we use later.
Add 5211 specific frame types.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I carefully reviewed desh.h against the HAL sources. Added comments and made
differences between 5210, 5211 and 5212 more clear by adding _521x to the
defines which are specific to that chipset. Renamed some defines. No functional
changes.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_hw_rx_error was only used once, where we could easily just use
ath5k_hw_rx_status as well, so remove it.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Just whitespace and indentation.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use direct function calls for ath5k_hw_setup_rx_desc() and
ath5k_hw_setup_mrr_tx_desc() instead of a function pointer which always pointed
to the same function in the case of ath5k_hw_setup_rx_desc() and which is
easily unified in the case of ath5k_hw_setup_mrr_tx_desc().
Also simplify the initialization function for the remaining function pointers.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Create a new function ath5k_receive_frame_ok() which checks for errors, updates
error statistics and tells us if we want to further "receive" this frame or
not. This way we can avoid a goto and have a cleaner separation between buffer
handling and other things.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move frame reception into it's own function to have a clearer separation
between buffer and descriptor handling and things that are done when we
actually receive a frame.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no reason for a special handling (return) here, just break like we do
with the checks before.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After we free skbs for receive or transmit descriptors, make sure we have no
pointers to the now invalid memory address.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the debug ouptut rx_status_0 was printed twice instead of rx_status_1. Also
make the debug message more clear.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix comment about dma sizes, brackets were missing. Replace 'insure' with
'ensure'.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename ath5k_txbuf_free() to ath5k_txbuf_free_skb() since this is what it does:
it frees the skb and not the buf. Same for ath5k_rxbuf_free().
Signed-off-by: Bruno Randolf <br1@einfach.org>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
BugLink: http://bugs.launchpad.net/bugs/21367
Enable LED by default and update the MODULE_PARM_DESC. The original
reason for defaulting to disabled was documented in 2005 and noted, "The
LED code has been reported to hang some systems when running ifconfig
and is therefore disabled by default." This no longer appears
applicable and users have been requesting this be enabled for several
years.
Signed-off-by: TJ <ubuntu@tjworld.net>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Acked-by: Stefan Bader <stefan.bader@canonical.com>
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Medion MD40900 device id [0x0cde, 0x0006] is defined twice.
Comment out the duplicate.
Originally-by: Ben Collins <ben.collins@ubuntu.com>
Signed-off-by: Leann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
0x49 is used by PLANEX GW-US54GXS (2019:5303).
Signed-off-by: Kouhei Sutou <kou@clear-code.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SKBs hold onto resources that can't be held indefinitely, such as TCP
socket references and netfilter conntrack state. So if a packet is left
in TX ring for a long time, there might be a TCP socket that cannot be
closed and freed up.
Current blackfin EMAC driver always reclaim and free used tx skbs in future
transfers. The problem is that future transfer may not come as soon as
possible. This patch start a timer after transfer to reclaim and free skb.
There is nearly no performance drop with this patch.
TX interrupt is not enabled because of a strange behavior of the Blackfin EMAC.
If EMAC TX transfer control is turned on, endless TX interrupts are triggered
no matter if TX DMA is enabled or not. Since DMA walks down the ring automatically,
TX transfer control can't be turned off in the middle. The only way is to disable
TX interrupt completely.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the code that handles the error case when cnic_cm_abort() cannot
proceed normally. We cannot just set the csk->state and we must
go through cnic_ready_to_close() to handle all the conditions. We
also add error return code in cnic_cm_abort().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Combine RESET_RECEIVED and RESET_COMP logic and fix race condition
between these 2 events and cnic_cm_close(). In particular, we need
to (test_and_clear_bit(SK_F_OFFLD_COMPLETE, &csk->flags)) before we
update csk->state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move chip-specific code to the respective chip's ->close_conn() functions
for better code organization.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So that bnx2i can handle the error condition immediately and not have to
wait for timeout.
Signed-off-by: Michael Chan <mchan@broadcom.com.
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change corrects issues where macvlan was not correctly triggering
promiscuous mode on ixgbe due to the filters not being correctly set. It
also corrects the fact that VF rar filters were being overwritten when the
PF was reset.
CC: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that ampdu_action() can sleep, remove all
the driver hacks and just issue WMI commands
to the target.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
IBSS requires the cwmin and cwmax to be respected when
we reset the txqueues on AR9003 otherwise the distribution
of beacons will be balanced towards the AR9003 card first
preventing equal contention for air time for other peers
on the IBSS.
Without this IBSS will work but only the AR9003 card will be
be issuing beacons on the IBSS.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Legacy rt2870 driver handles WCID differently then we expected,
the BSSID and Cipher value are 3 bit values, while the 4th bit
should be set elsewhere in an extended field.
After this, rt2800usb reports frames have been decrypted
successfully, indicating that the Hardware decryption now is
working correctly.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hardware cryptography seems to be working
on a 11G network with WPA/WPA2 cryptography
enabled. WEP still needs to be tested...
Signed-of-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Similar to rt2800pci, remove the check for duplicate
register reading, and instead limit the for-loop to
the maximum number of TX entries inside a queue.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800lib has been under development of the rt2x00 project,
so add it to the author string for the module information.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Explicitly enable the usage of fallback rates for
the transmission of frames with rt61pci and rt73usb hardware.
Note that for txdone reporting, only rt61pci is capable of
reporting the fallback rates, for USB it is not possible
to determine the number of retries. However the device will
use the fallback rates, so it might still help in the performance.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some corner cases the reported tx rates/retries didn't match the really
used ones.
The hardware lowers the tx rate on each consecutive retry by 1 (but won't
fall back from MCS to legacy rates) _until_ it reaches the lowest one.
In case the frame wasn't sent succesful the number of retries is 7 and if
a rate index <7 was used the previous code reported negative rate indexes
which were then ignored by the rate control algorithm and mac80211.
Instead, report the remaining number of retries to have happened with
the lowest rate (index 0). This should give the rate control algorithm
slightly more accurate information about the used tx rates/retries.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set up max_rates and max_rate_tries with suitable values even if we do not
support the whole functionality.
As rt2800 has a global fallback table we cannot specify more then one tx rate
per frame but since the hw will try several different rates (based on the
fallback table) we should still initialize max_rates to the maximum number of
rates we are going to try. Otherwise mac80211 will truncate our reported tx
rates and the rc algortihm will end up with incorrect data choosing unsuitable
rates for tx.
This improves throughput on rt2800 devices considerable.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix typo in rt2800_config_txpower.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently rt2800pci will read TX_STA_FIFO until the previously read value
matches the current value. However, it is obvious that TX_STA_FIFO only
contains values that can easily be the same for multiple consecutive frames
(especially when communicating with only one other STA). Hence, we often
ended up with reading only the first entry and ignoring the rest.
One result was that when the TX_STA_FIFO contained multiple entires, only
the first one was read and properly handled while the others remained in the
tx queue.
Thus, drop this check but introduce a maximum number of reads. All legacy
drivers use the size of the tx ring as limit but state that the TX_STA_FIFO
has only 16 entries. So, let's just stick with the tx ring size for now.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dimitris Michailidis