Check in vlv_crtc_clock_get if DPLL is enabled before calling dpio read.
It will not be enabled for DSI and avoid dpio read WARN dumps.
Absence of ->get_config was causing other WARN dumps as well. Update
dpll_hw_state as well correctly
v2: Address review comments by Daniel
- Check if DPLL is enabled rather than checking pipe output type
- set adjusted_mode->flags to 0 in compute_config rather than using
pipe_config->quirks
- Add helper function in intel_dsi_pll.c and use that in intel_dsi.c
- updated dpll_hw_state correctly
- Updated commit message and title
v3: Address review comments by Imre
- Proper masking of P1, M1 fields while computing divisors
- assert in case of bpp mismatch
- guard for divide by 0 while computing pclk
- Use ARRAY_SIZE instead of direct calculation
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Basically check for both +ive and -ive deviation from target clock and
pick the one with minimal error. If we get a direct match, break from
loop to acheive some optimization.
v2: Use signed variable for target and calculated dsi clock values
Signed-off-by: Vijayakumar Balakrishnan <vijayakumar.balakrishnan@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Pixel clock based calculation is recommended in the MIPI host controller
documentation
v2: Based on review comments from Jani and Ville
- Use dsi_clk in KHz rather than converting in Hz and back to MHz
- RR formula is retained though not used but return dsi_clk in KHz now
- Moved the m-n-p changes into a separate patch
- Removed the parameter check for intel_dsi->dsi_clock_freq. This will be
bought back in if needed when appropriate panel drivers are done
v3: Removed the unused mnp calculation from static table
Signed-off-by: Vijayakumar Balakrishnan <vijayakumar.balakrishnan@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
adjusted_mode contains our real timings, not requested_mode. Use the
correct thing in DSI PLL code.
Also constify adjusted_mode since we don't change it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
v2:
- Grab dpio_lock mutex in vlv_enable_dsi_pll().
- Add and call vlv_disable_dsi_pll().
v3: Mostly based on Ville's review comments.
- Only pipe A has DSI PLL lock bit.
- Add more of CCK REG bit definitions for DSI PLL.
- Make tables static.
- Move clock gating out of the clock calculation functions.
- DSI PLL LDO power gating.
- Put alternative MNP from table calc behind #ifdef.
v4: s/CKK/CLK/ in the CCK REG bit definitions (Ville).
Signed-off-by: ymohanma <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Shobhit Kumar