Because of some quirk in the SCSI spec the aic79xx driver chose to
force a renegotiation when sending an inquiry. This should better
be handled by the upper layers if required at all.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch fixes the aic79xx driver to properly respond to BIOS
settings.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On certain systems the driver seems to hit upon some
"scsi0: Invalid Sequencer interrupt occurred." problem and dumps card state.
According to Adaptec engineers this message is harmless. So as not to
confuse user we can as well disable the internal card state dump and
just print out the message itself.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates the error recovery. Routines for TARGET RESET
and ABORT COMMAND are split up as the logic is quite dissimilar.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch converts aic79xx to use the midlayer-supplied tcq
functions.
We also set the queuedepth to '1' if tcq is disabled; the
aic79xx driver gets confused otherwise. Will set it back to
'2' once I figure out how to queue requests in the driver.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch removes the need for platform_data->qfrozen.
We're now using complete() instead of semaphores thus
simplifying ahd_freeze_simq() quite a lot.
This also fixes some deadlocks in the recovery code (again).
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On Tue, Jan 31, 2006 at 06:20:18PM +0100, Christoph Hellwig wrote:
> switch eh_sem to a completion. due to wait_for_completion_timeout this
> also nicely simplifies the code. Unfortunately it's untested, so if
> someone with the hardware could give it a try that would be nice. Once
> it works the same thing can be applied to aic79xx.
New version that switches to the common onstack completion and just a
pointer in the platform_data struct idiom. This gets rid of all the
flags fiddling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Introduce new helpers:
- spi_populate_width_msg()
- spi_populate_sync_msg()
- spi_populate_ppr_msg()
and use them in drivers which already enable the SPI transport.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix the timer handling in aic79xx to use the SCSI-ML provided handling
instead of implementing our own.
It also fixes a deadlock in the command recovery code.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates the aic79xx sequencer with latest fixes from adaptec.
The sequencer code now corresponds with adaptec version 2.0.15.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This takes us past the old 1.x version of the SCSI driver and the 2.x
version of the aic website version to reflect the full incorporation
of both branches.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver is doing a rather stupid mod_timer allegedly to "give
request sense more time to complete". This is illegal and pointless,
so just eliminate it. Also eliminate all the other uses of struct
timer_list in the driver, which are mostly bogus.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Ignore all files generated from *_shipped files, plus a few others.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Add scsi_add_host() failure handling for aic7xxx
Also silence a compiler warning :
drivers/scsi/aic7xxx/aic7xxx_osm.c: In function `ahc_linux_register_host':
drivers/scsi/aic7xxx/aic7xxx_osm.c:1100: warning: ignoring return value of `scsi_add_host', declared with attribute warn_unused_result
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add scsi_add_host() failure handling for aic79xx
Also silence a compiler warning :
drivers/scsi/aic7xxx/aic79xx_osm.c: In function `ahd_linux_register_host':
drivers/scsi/aic7xxx/aic79xx_osm.c:1099: warning: ignoring return value of `scsi_add_host', declared with attribute warn_unused_result
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
To transport scsi reset command to device aic7xxx reset handler looks
at the driver's pending_list and searches any proper command. However
the search condition has been inverted: ahc_match_scb() returns TRUE
if a matched command is found. As a result the reset on required
devices did not turn out well, a correctly working neighbour device
may be surprised by the reset. aic7xxx reset handler reports about the
success, but really the original situation is not corrected yet.
Signed-off-by: Vasily Averin <vvs@sw.ru>
Naturally, there's a corresponding problem in the aic79xx driver, so
I've also added the same fix for that.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch removes almost all inclusions of linux/version.h. The 3
#defines are unused in most of the touched files.
A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.
There are also lots of #ifdef for long obsolete kernels, this was not
touched. In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.
quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`
search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
just take the internal lock in queuecommand instead. also switch
the only direct use of the internal lock to the wrappers used elsewhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
just take the internal lock in queuecommand instead. also switch
the only direct use of the internal lock to the wrappers used elsewhere.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Wrap a highly common idiom. Makes the code easier to read, helps pave
the way for sdev->{id,channel} removal, and adds a token that can easily
by grepped-for in the future.
There are a couple sdev_id() and scmd_printk() updates thrown in as well.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In these drivers, scsi_remove_host() is called too late, at the point
it is called, the driver has already shut down too far to accept any
I/O that the shutdown might generate. Any generated I/O actually
triggers a panic.
Fix this by calling scsi_remove_host() as early as possible and not
calling scsi_host_put() until just before we kfree the ahc_softc.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch moves aic7xxx over to the dma_get_required_mask() API and
dumps its open coded memory check.
It also appears from this bug:
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=167049
That 39 bit addressing doesn't work on older cards. I surmise that the
AHC_LARGE_SCBS flag is the one that marks cards capable of using 39 bit
addressing, so I also folded that check into the code.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
#include of C files and macro tricks to rename symbols are evil and just
cause trouble. Let's doublicate the two functions as they're going to
go away soon enough anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
remove lots of completely dead code from aiclib, there's not a lot left
and even what's left is rather useless.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
remove ahd_tailq and do sane pci probing. ported over from aic7xxx.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
remove some dead cruft, as done already in aic7xxx
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Christoph Hellwig <hch@lst.de>
Multi-function cards need to inherit the PCI flags from the master PCI
device.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: "Martin J. Bligh" <mbligh@mbligh.org>
drivers/scsi/aic7xxx/aic7770.c: In function `aic7770_config':
drivers/scsi/aic7xxx/aic7770.c:129: warning: unused variable `l'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a spurious (and illegal since it's marked __exit) call to
ahc_linux_exit() in ahc_linux_init() which causes a double list
deletion of the transport class; remove it.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
without it you get this failure:
drivers/built-in.o(.text+0xdcccd): In function `ahd_linux_slave_configure':
drivers/scsi/aic7xxx/aic79xx_osm.c:636: undefined reference to `spi_dv_device'
drivers/built-in.o(.text+0xdd7b1): In function `ahd_send_async':
drivers/scsi/aic7xxx/aic79xx_osm.c:1652: undefined reference to `spi_display_xfer_agreement'
drivers/built-in.o(.init.text+0x7b4d): In function `ahd_linux_init':
drivers/scsi/aic7xxx/aic79xx_osm.c:2765: undefined reference to `spi_attach_transport'
drivers/built-in.o(.init.text+0x7c94):drivers/scsi/aic7xxx/aic79xx_osm.c:2774: undefined reference to `spi_release_transport'
drivers/built-in.o(.exit.text+0x72c): In function `ahd_linux_exit':
drivers/scsi/aic7xxx/aic79xx_osm.c:2783: undefined reference to `spi_release_transport'
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch upports all relevant code fixes and bumps the driver version
to 7.0 to signify starting a new tree.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
this patch is just a cross-port of the fixup for aic7xxx DT settings.
As the same restrictions apply for aic79xx also (DT requires wide
transfers) the dt setting routine should be modified equivalently.
And an invalid period setting will be caught by ahd_find_syncrate()
anyway.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Several people noticed we dropped quite a bit on benchmark figures.
OK, it was my fault but unfortunately I discovered I ran out of brown
paper bags a while ago and forgot to reorder them.
The issue is that a construct introduced in the conversion of the
driver to use the transport class keyed off whether the block request
was tagged or not. However, the aic7xxx driver doesn't properly set
up the block layer TCQ (it uses the wrong API), so the driver now
things all requests are untagged and we keep it to a queue depth of a
single element. Oops.
The fix is to use the correct TCQ API.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a slight problem in the way you've done the transport
parameters; reading from the variables actually produces the current
settings, not the ones you just set (and there's usually a lag because
devices don't renegotiate until the next command goes over the bus). If
you set the bit immediately, you get into the situation where the
transport parameters report something as being set even if the drive
cannot support it.
I patched the driver to do it this way and also corrected a panic in the
proc routines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch updates various scsi_transport_spi parameters with the actual
parameters used by the driver internally.
Domain Validation for all devices should now work properly.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hannes Reinecke