The debugfs support in batman-adv was marked as deprecated by the commit
00caf6a2b3 ("batman-adv: Mark debugfs functionality as deprecated") and
scheduled for removal in 2021.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Since now we have src in br_ip, u no longer makes sense so rename
it to dst. No functional changes.
v2: fix build with CONFIG_BATMAN_ADV_MCAST
CC: Marek Lindner <mareklindner@neomailbox.ch>
CC: Simon Wunderlich <sw@simonwunderlich.de>
CC: Antonio Quartulli <a@unstable.cc>
CC: Sven Eckelmann <sven@narfation.org>
CC: b.a.t.m.a.n@lists.open-mesh.org
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two minor conflicts:
1) net/ipv4/route.c, adding a new local variable while
moving another local variable and removing it's
initial assignment.
2) drivers/net/dsa/microchip/ksz9477.c, overlapping changes.
One pretty prints the port mode differently, whilst another
changes the driver to try and obtain the port mode from
the port node rather than the switch node.
Signed-off-by: David S. Miller <davem@davemloft.net>
Scenario:
* Multicast frame send from a BLA backbone (multiple nodes with
their bat0 bridged together, with BLA enabled)
Issue:
* BLA backbone nodes receive the frame multiple times on bat0
For multicast frames received via batman-adv broadcast packets the
originator of the broadcast packet is checked before decapsulating and
forwarding the frame to bat0 (batadv_bla_is_backbone_gw()->
batadv_recv_bcast_packet()). If it came from a node which shares the
same BLA backbone with us then it is not forwarded to bat0 to avoid a
loop.
When sending a multicast frame in a non-4-address batman-adv unicast
packet we are currently missing this check - and cannot do so because
the batman-adv unicast packet has no originator address field.
However, we can simply fix this on the sender side by only sending the
multicast frame via unicasts to interested nodes which do not share the
same BLA backbone with us. This also nicely avoids some unnecessary
transmissions on mesh side.
Note that no infinite loop was observed, probably because of dropping
via batadv_interface_tx()->batadv_bla_tx(). However the duplicates still
utterly confuse switches/bridges, ICMPv6 duplicate address detection and
neighbor discovery and therefore leads to long delays before being able
to establish TCP connections, for instance. And it also leads to the Linux
bridge printing messages like:
"br-lan: received packet on eth1 with own address as source address ..."
Fixes: 2d3f6ccc4e ("batman-adv: Modified forwarding behaviour for multicast packets")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
checkpatch found various instances of "Possible repeated word" in various
comments.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The usage of the '/* fall through */' comments in switches are no longer
marked as non-deprecated variant of implicit fall throughs for switch
statements. The commit 294f69e662 ("compiler_attributes.h: Add
'fallthrough' pseudo keyword for switch/case use") introduced a replacement
keyword which should be used instead.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The multicast code uses the lists bat_priv->mcast.want_all_rtr*_list to
store all all originator nodes which don't have the flag no-RTR4 or no-RTR6
set. When an originator is purged, it has to be removed from these lists.
Since all entries without the BATADV_MCAST_WANT_NO_RTR4/6 are stored in
these lists, they have to be handled like entries which have these flags
set to force the update routines to remove them from the lists when purging
the originator.
Not doing so will leave a pointer to a freed memory region inside the list.
Trying to operate on these lists will then cause an use-after-free error:
BUG: KASAN: use-after-free in batadv_mcast_want_rtr4_update+0x335/0x3a0 [batman_adv]
Write of size 8 at addr ffff888007b41a38 by task swapper/0/0
Fixes: 61caf3d109 ("batman-adv: mcast: detect, distribute and maintain multicast router presence")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Acked-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The bucket variable is only updated outside the loop over the mcast_flags
buckets. It will only be updated during a dumping run when the dumping has
to be interrupted and a new message has to be started.
This could result in repeated or missing entries when the multicast flags
are dumped to userspace.
Fixes: d2d489b7d8 ("batman-adv: Add inconsistent multicast netlink dump detection")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Now that we not only track the presence of multicast listeners but also
multicast routers we can safely apply group-aware multicast-to-unicast
forwarding to packets with a destination address of scope greater than
link-local as well.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
To be able to apply our group aware multicast optimizations to packets
with a scope greater than link-local we need to not only keep track of
multicast listeners but also multicast routers.
With this patch a node detects the presence of multicast routers on
its segment by checking if
/proc/sys/net/ipv{4,6}/conf/<bat0|br0(bat)>/mc_forwarding is set for one
thing. This option is enabled by multicast routing daemons and needed
for the kernel's multicast routing tables to receive and route packets.
For another thing if a bridge is configured on top of bat0 then the
presence of an IPv6 multicast router behind this bridge is currently
detected by checking for an IPv6 multicast "All Routers Address"
(ff02::2). This should later be replaced by querying the bridge, which
performs proper, RFC4286 compliant Multicast Router Discovery (our
simplified approach includes more hosts than necessary, most notably
not just multicast routers but also unicast ones and is not applicable
for IPv4).
If no multicast router is detected then this is signalized via the new
BATADV_MCAST_WANT_NO_RTR4 and BATADV_MCAST_WANT_NO_RTR6
multicast tvlv flags.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
When a bridge is added on top of bat0 we set the WANT_ALL_UNSNOOPABLES
flag. Which means we sign up for all traffic for ff02::1/128 and
224.0.0.0/24.
When the node itself had IPv6 enabled or joined a group in 224.0.0.0/24
itself then so far this would result in a multicast TT entry which is
redundant to the WANT_ALL_UNSNOOPABLES.
With this patch such redundant TT entries are avoided.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Instead of collecting multicast MAC addresses from the netdev hw mc
list collect a node's multicast listeners from the IP lists and convert
those to MAC addresses.
This allows to exclude addresses of specific scope later. On a
multicast MAC address the IP destination scope is not visible anymore.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is not necessary to hold the mla_lock spinlock during the whole
multicast tt/tvlv worker callback. Just holding it during the checks and
updates of the bat_priv stored multicast flags and mla_list is enough.
Therefore this patch splits batadv_mcast_mla_tvlv_update() in two:
batadv_mcast_mla_flags_get() at the beginning of the worker to gather
and calculate the new multicast flags, which does not need any locking
as it neither reads from nor writes to bat_priv->mcast.
And batadv_mcast_mla_flags_update() at the end of the worker which
commits the newly calculated flags and lists to bat_priv->mcast and
therefore needs the lock.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
- bump version strings, by Simon Wunderlich (we forgot to include
this patch previously ...)
- fix multicast tt/tvlv worker locking, by Linus Lüssing
-----BEGIN PGP SIGNATURE-----
iQJKBAABCgA0FiEE1ilQI7G+y+fdhnrfoSvjmEKSnqEFAlzUKp4WHHN3QHNpbW9u
d3VuZGVybGljaC5kZQAKCRChK+OYQpKeoX1kD/oCq7+iLO1oaewGrD/gnrGJu2Wk
FDlVRRBvUOwdJM2zo7o5xLCU1+Pohv0H5uBIXUw4vhcXoqhkqyysLz9lotPrxRG1
KD1Jl8FwOPLkSiLPxj7QurfBU8G0V/A7fYkAt+RTTkk9iSniL8lCc6hE6hj6KimP
GaqnkYJyudhOkimYyLb4exUfq4Ls7J95x3LhN+YzXk8PgN3qgrD/dVuSu7dmuyse
bfTP1dyWBtQiByEZqNCqrWnj2nBTvCQW9UwuOCg1W1z5coh5GWXTvL61ePu35/Vn
0LxUNNHbbkjVwbVz9T3ExMTHlrV2nEOaZnw4kiuVAbqDNDqG5XkqD1iG2H5wVh74
BPTtk2hd2b8PrvBsyzj2Q+RaTEk0o3jIbP6A/jM+9GpVukT1M0SohcYEFISUeh1f
PXMBpAc7qVrP8+VefCkXGFWbKyRg60k2cJQipS/Q9Aef7xOv8DyDbOrnd/a5xPUS
zXFRAsKx16gA8SUxNgYz/67jwamVhplHSpgKG2KFtEh0CxJJBY7Z9hlEPM3uZLmT
QHUbTS+FTlBNS/Go48pnGd5QTEGNeP5gQkiovtLmIRULRTfbwbI1/4VQCp9/XahT
Vj+4RhhULC7i4joqEeKv+GyO36tydsU93yBt66Xo0JI8W9SLfga5zREdrmlGYRZr
ECBszSxPpQ8zp3A2Hg==
=Dq5n
-----END PGP SIGNATURE-----
Merge tag 'batadv-net-for-davem-20190509' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich (we forgot to include
this patch previously ...)
- fix multicast tt/tvlv worker locking, by Linus Lüssing
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot has reported some issues with the locking assumptions made for
the multicast tt/tvlv worker: It was able to trigger the WARN_ON() in
batadv_mcast_mla_tt_retract() and batadv_mcast_mla_tt_add().
While hard/not reproduceable for us so far it seems that the
delayed_work_pending() we use might not be quite safe from reordering.
Therefore this patch adds an explicit, new spinlock to protect the
update of the mla_list and flags in bat_priv and then removes the
WARN_ON(delayed_work_pending()).
Reported-by: syzbot+83f2d54ec6b7e417e13f@syzkaller.appspotmail.com
Reported-by: syzbot+050927a651272b145a5d@syzkaller.appspotmail.com
Reported-by: syzbot+979ffc89b87309b1b94b@syzkaller.appspotmail.com
Reported-by: syzbot+f9f3f388440283da2965@syzkaller.appspotmail.com
Fixes: cbebd363b2 ("batman-adv: Use own timer for multicast TT and TVLV updates")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
With this patch multicast packets with a limited number of destinations
(current default: 16) will be split and transmitted by the originator as
individual unicast transmissions.
Wifi broadcasts with their low bitrate are still a costly undertaking.
In a mesh network this cost multiplies with the overall size of the mesh
network. Therefore using multiple unicast transmissions instead of
broadcast flooding is almost always less burdensome for the mesh
network.
The maximum amount of unicast packets can be configured via the newly
introduced multicast_fanout parameter. If this limit is exceeded
distribution will fall back to classic broadcast flooding.
The multicast-to-unicast conversion is performed on the initial
multicast sender node and counts on a final destination node, mesh-wide
basis (and not next hop, neighbor node basis).
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
All files got a SPDX-License-Identifier with commit 7db7d9f369
("batman-adv: Add SPDX license identifier above copyright header"). All the
required information about the license conditions can be found in
LICENSES/.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
- bump version strings, by Simon Wunderlich
- Add DHCPACKs for DAT snooping, by Linus Luessing
- Update copyright years for 2019, by Sven Eckelmann
-----BEGIN PGP SIGNATURE-----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=G6IW
-----END PGP SIGNATURE-----
Merge tag 'batadv-next-for-davem-20190201' of git://git.open-mesh.org/linux-merge
Simon Wunderlich says:
====================
This feature/cleanup patchset includes the following patches:
- bump version strings, by Simon Wunderlich
- Add DHCPACKs for DAT snooping, by Linus Luessing
- Update copyright years for 2019, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refactors ip_mc_check_igmp(), ipv6_mc_check_mld() and
their callers (more precisely, the Linux bridge) to not rely on
the skb_trimmed parameter anymore.
An skb with its tail trimmed to the IP packet length was initially
introduced for the following three reasons:
1) To be able to verify the ICMPv6 checksum.
2) To be able to distinguish the version of an IGMP or MLD query.
They are distinguishable only by their size.
3) To avoid parsing data for an IGMPv3 or MLDv2 report that is
beyond the IP packet but still within the skb.
The first case still uses a cloned and potentially trimmed skb to
verfiy. However, there is no need to propagate it to the caller.
For the second and third case explicit IP packet length checks were
added.
This hopefully makes ip_mc_check_igmp() and ipv6_mc_check_mld() easier
to read and verfiy, as well as easier to use.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netlink dump functionality transfers a large number of entries from the
kernel to userspace. It is rather likely that the transfer has to
interrupted and later continued. During that time, it can happen that
either new entries are added or removed. The userspace could than either
receive some entries multiple times or miss entries.
Commit 670dc2833d ("netlink: advertise incomplete dumps") introduced a
mechanism to inform userspace about this problem. Userspace can then decide
whether it is necessary or not to retry dumping the information again.
The netlink dump functions have to be switched to exclusive locks to avoid
changes while the current message is prepared. The already existing
generation sequence counter from the hash helper can be used for this
simple hash.
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Instead of disabling multicast optimizations mesh-wide once a node with
no multicast optimizations capabilities joins the mesh, do the
following:
Just insert such nodes into the WANT_ALL_IPV4/IPV6 lists. This is
sufficient to avoid multicast packet loss to such unsupportive nodes.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
In the case where hard_iface is NULL, the error path may pass a null
pointer to batadv_hardif_put causing a null pointer dereference error.
Avoid this by only calling the function if hard_iface not null.
Detected by CoverityScan, CID#1466456 ("Explicit null dereferenced")
Fixes: 53dd9a68ba ("batman-adv: add multicast flags netlink support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Minor conflicts in drivers/net/ethernet/mellanox/mlx5/core/en_rep.c,
we had some overlapping changes:
1) In 'net' MLX5E_PARAMS_LOG_{SQ,RQ}_SIZE -->
MLX5E_REP_PARAMS_LOG_{SQ,RQ}_SIZE
2) In 'net-next' params->log_rq_size is renamed to be
params->log_rq_mtu_frames.
3) In 'net-next' params->hard_mtu is added.
Signed-off-by: David S. Miller <davem@davemloft.net>
For multicast frames AP isolation is only supposed to be checked on
the receiving nodes and never on the originating one.
Furthermore, the isolation or wifi flag bits should only be intepreted
as such for unicast and never multicast TT entries.
By injecting flags to the multicast TT entry claimed by a single
target node it was verified in tests that this multicast address
becomes unreachable, leading to packet loss.
Omitting the "src" parameter to the batadv_transtable_search() call
successfully skipped the AP isolation check and made the target
reachable again.
Fixes: 1d8ab8d3c1 ("batman-adv: Modified forwarding behaviour for multicast packets")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Fun set of conflict resolutions here...
For the mac80211 stuff, these were fortunately just parallel
adds. Trivially resolved.
In drivers/net/phy/phy.c we had a bug fix in 'net' that moved the
function phy_disable_interrupts() earlier in the file, whilst in
'net-next' the phy_error() call from this function was removed.
In net/ipv4/xfrm4_policy.c, David Ahern's changes to remove the
'rt_table_id' member of rtable collided with a bug fix in 'net' that
added a new struct member "rt_mtu_locked" which needs to be copied
over here.
The mlxsw driver conflict consisted of net-next separating
the span code and definitions into separate files, whilst
a 'net' bug fix made some changes to that moved code.
The mlx5 infiniband conflict resolution was quite non-trivial,
the RDMA tree's merge commit was used as a guide here, and
here are their notes:
====================
Due to bug fixes found by the syzkaller bot and taken into the for-rc
branch after development for the 4.17 merge window had already started
being taken into the for-next branch, there were fairly non-trivial
merge issues that would need to be resolved between the for-rc branch
and the for-next branch. This merge resolves those conflicts and
provides a unified base upon which ongoing development for 4.17 can
be based.
Conflicts:
drivers/infiniband/hw/mlx5/main.c - Commit 42cea83f95
(IB/mlx5: Fix cleanup order on unload) added to for-rc and
commit b5ca15ad7e (IB/mlx5: Add proper representors support)
add as part of the devel cycle both needed to modify the
init/de-init functions used by mlx5. To support the new
representors, the new functions added by the cleanup patch
needed to be made non-static, and the init/de-init list
added by the representors patch needed to be modified to
match the init/de-init list changes made by the cleanup
patch.
Updates:
drivers/infiniband/hw/mlx5/mlx5_ib.h - Update function
prototypes added by representors patch to reflect new function
names as changed by cleanup patch
drivers/infiniband/hw/mlx5/ib_rep.c - Update init/de-init
stage list to match new order from cleanup patch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump the list of multicast flags entries via the netlink socket.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
If a node signals that it wants all traffic for a specific protocol
family then there is no need to announce individual multicast addresses
via TT.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
As the kernel doc describes too the code is supposed to skip adding
multicast TT entries if both the WANT_ALL_IPV4 and WANT_ALL_IPV6 flags
are present.
Unfortunately, the current code even skips adding multicast TT entries
if only either the WANT_ALL_IPV4 or WANT_ALL_IPV6 is present.
This could lead to IPv6 multicast packet loss if only an IGMP but not an
MLD querier is present for instance or vice versa.
Fixes: 687937ab34 ("batman-adv: Add multicast optimization support for bridged setups")
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The header file is used by different userspace programs to inject packets
or to decode sniffed packets. It should therefore be available to them as
userspace header.
Also other components in the kernel (like the flow dissector) require
access to the packet definitions to be able to decode ETH_P_BATMAN ethernet
packets.
Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The documentation describing kernel-doc comments for functions ("How to
format kernel-doc comments") uses parentheses at the end of the function
name. Using this format allows to use a consistent style when adding
documentation to a function and when referencing this function in a
different kernel-doc section.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The linux/gfp.h provides the GFP_ATOMIC and GFP_KERNEL define. It should
therefore be included instead of linux/fs.h.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The "Linux kernel licensing rules" require that each file has a SPDX
license identifier as first line (and sometimes as second line).
The FSFE REUSE practices [1] would also require the same tags but have no
restrictions on the placement in the source file. Using the "Linux kernel
licensing rules" is therefore also fulfilling the FSFE REUSE practices
requirements at the same time.
[1] https://reuse.software/practices/
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
checkpatch introduced with commit 63b7c73ec8 ("checkpatch: add --strict
check for ifs with unnecessary parentheses") an additional test which
identifies some unnecessary parentheses.
Remove these unnecessary parentheses to avoid the warnings and to unify the
coding style slightly more.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
It is not necessary to disable these code sections in case other kernel
features are disabled. Instead the IS_ENABLED tests can be added directly
in the code and the compiler can remove the unnecessary code parts during
its optimization run.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Instead of latching onto the OGM period, this patch introduces a worker
dedicated to multicast TT and TVLV updates.
The reasoning is, that upon roaming especially the translation table
should be updated timely to minimize connectivity issues.
With BATMAN V, the idea is to greatly increase the OGM interval to
reduce overhead. Unfortunately, right now this could lead to
a bad user experience if multicast traffic is involved.
Therefore this patch introduces a fixed 500ms update interval for
multicast TT entries and the multicast TVLV.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
batadv_mcast_mla_list_free() just frees some leftovers of a local feast
in batadv_mcast_mla_update(). No lockdep needed as it has nothing to do
with bat_priv->mcast.mla_list.
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The files provided by batman-adv via debugfs are currently converted to
netlink. Tools which are not yet converted to use the netlink interface may
still rely on the old debugfs files. But systems which already upgraded
their tools can save some space by disabling this feature. The default
configuration of batman-adv on amd64 can reduce the size of the module by
around 11% when this feature is disabled.
$ size net/batman-adv/batman-adv.ko*
text data bss dec hex filename
150507 10395 4160 165062 284c6 net/batman-adv/batman-adv.ko.y
137106 7099 2112 146317 23b8d net/batman-adv/batman-adv.ko.n
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This silences the following coccinelle warning:
"WARNING: sum of probable bitmasks, consider |"
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
There are several places in batman-adv which provide logging related
functions. These should be grouped together in the log.* files to make them
easier to find.
Reported-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
The tvlv functionality in main.c is mostly unrelated to the rest of the
content. It still takes up a large portion of this source file (~45%, 588
lines). Moving it to a separate file makes it better visible as a main
component of the batman-adv implementation and hides it less in the other
helper functions in main.c
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
[sven@narfation.org: fix conflicts with current version, fix includes,
rewrote commit message]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
This patch adds a debugfs table with originators and their according
multicast flags to help users figure out why multicast optimizations
might be enabled or disabled for them.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
With this patch changes relevant to a node's own multicast flags are
printed to the 'mcast' log level.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
With this patch we are finally able to support multicast optimizations
in bridged setups, too. So far, if a bridge was added on top of a
soft-interface (e.g. bat0) the batman-adv multicast optimizations
needed to be disabled to avoid packetloss.
Current Linux bridge implementations and API can now provide us
with the so far missing information about interested but "remote"
multicast receivers behind bridge ports.
The Linux bridge performs the detection of remote participants
interested in multicast packets with its own and mature so
called IGMP and MLD snooping code and stores that in its
database. With the new API provided by the bridge batman-adv can
now simply hook into this database.
We then reliably announce the gathered multicast listeners to
other nodes through the batman-adv translation table.
Additionally, the Linux bridge provides us with the information about
whether an IGMP/MLD querier exists. If there is none then we need to
disable multicast optimizations as we cannot learn about multicast
listeners on external, bridged-in host then.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
With this patch IGMP or MLD reports are always flooded. This is
necessary for the upcoming bridge integration to function without
multicast packet loss.
With the report handling so far bridges might miss interested multicast
listeners, leading to wrongly excluding ports from multicast packet
forwarding.
Currently we are treating IGMP/MLD reports, the messages bridges use to
learn about interested multicast listeners, just as any other multicast
packet: We try to send them to nodes matching its multicast destination.
Unfortunately, the destination address of reports of the older
IGMPv2/MLDv1 protocol families do not strictly adhere to their own
protocol: More precisely, the interested receiver, an IGMPv2 or MLDv1
querier, itself usually does not listen to the multicast destination
address of any reports.
Therefore with this patch we are simply excluding IGMP/MLD reports from
the multicast forwarding code path and keep flooding them. By that
any bridge receives them and can properly learn about listeners.
To avoid compatibility issues with older nodes not yet implementing this
report handling, we need to force them to flood reports: We do this by
bumping the multicast TVLV version to 2, effectively disabling their
multicast optimization.
Tested-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <linus.luessing@c0d3.blue>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Sven Eckelmann