- Support for the MIPSr6 MemoryMapID register & Global INValidate TLB
(GINVT) instructions, allowing for more efficient TLB maintenance when
running on a CPU such as the I6500 that supports these.
- Enable huge page support for MIPS64r6.
- Optimize post-DMA cache sync by removing that code entirely for kernel
configurations in which we know it won't be needed.
- The number of pages allocated for interrupt stacks is now calculated
correctly, where before we would wastefully allocate too much memory
in some configurations.
- The ath79 platform migrates to devicetree.
- The bcm47xx platform sees fixes for the Buffalo WHR-G54S board.
- The ingenic/jz4740 platform gains support for appended devicetrees.
- The cavium_octeon, lantiq, loongson32 & sgi-ip27 platforms all see
cleanups as do various pieces of core architecture code.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXH3BQxUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN1+4wD+Oh4JTfZN/NEOQMlrSkXxjEHqjX3u
1Y6CiiPCs+q2UnYBANb+ic+ZH5MnvJxxmcvlYI2q3rIh4b8TDriip4KMUTUP
=Sw9X
-----END PGP SIGNATURE-----
Merge tag 'mips_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
- Support for the MIPSr6 MemoryMapID register & Global INValidate TLB
(GINVT) instructions, allowing for more efficient TLB maintenance
when running on a CPU such as the I6500 that supports these.
- Enable huge page support for MIPS64r6.
- Optimize post-DMA cache sync by removing that code entirely for
kernel configurations in which we know it won't be needed.
- The number of pages allocated for interrupt stacks is now calculated
correctly, where before we would wastefully allocate too much memory
in some configurations.
- The ath79 platform migrates to devicetree.
- The bcm47xx platform sees fixes for the Buffalo WHR-G54S board.
- The ingenic/jz4740 platform gains support for appended devicetrees.
- The cavium_octeon, lantiq, loongson32 & sgi-ip27 platforms all see
cleanups as do various pieces of core architecture code.
* tag 'mips_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (66 commits)
MIPS: lantiq: Remove separate GPHY Firmware loader
MIPS: ingenic: Add support for appended devicetree
MIPS: SGI-IP27: rework HUB interrupts
MIPS: SGI-IP27: do boot CPU init later
MIPS: SGI-IP27: do xtalk scanning later
MIPS: SGI-IP27: use pr_info/pr_emerg and pr_cont to fix output
MIPS: SGI-IP27: clean up bridge access and header files
MIPS: SGI-IP27: get rid of volatile and hubreg_t
MIPS: irq: Allocate accurate order pages for irq stack
MIPS: dma-noncoherent: Remove bogus condition in dma_sync_phys()
MIPS: eBPF: Remove REG_32BIT_ZERO_EX
MIPS: eBPF: Always return sign extended 32b values
MIPS: CM: Fix indentation
MIPS: BCM47XX: Fix/improve Buffalo WHR-G54S support
MIPS: OCTEON: program rx/tx-delay always from DT
MIPS: OCTEON: delete board-specific link status
MIPS: OCTEON: don't lie about interface type of CN3005 board
MIPS: OCTEON: warn if deprecated link status is being used
MIPS: OCTEON: add fixed-link nodes to in-kernel device tree
MIPS: Delete unused flush_cache_sigtramp()
...
Pull networking updates from David Miller:
"Here we go, another merge window full of networking and #ebpf changes:
1) Snoop DHCPACKS in batman-adv to learn MAC/IP pairs in the DHCP
range without dealing with floods of ARP traffic, from Linus
Lüssing.
2) Throttle buffered multicast packet transmission in mt76, from
Felix Fietkau.
3) Support adaptive interrupt moderation in ice, from Brett Creeley.
4) A lot of struct_size conversions, from Gustavo A. R. Silva.
5) Add peek/push/pop commands to bpftool, as well as bash completion,
from Stanislav Fomichev.
6) Optimize sk_msg_clone(), from Vakul Garg.
7) Add SO_BINDTOIFINDEX, from David Herrmann.
8) Be more conservative with local resends due to local congestion,
from Yuchung Cheng.
9) Allow vetoing of unsupported VXLAN FDBs, from Petr Machata.
10) Add health buffer support to devlink, from Eran Ben Elisha.
11) Add TXQ scheduling API to mac80211, from Toke Høiland-Jørgensen.
12) Add statistics to basic packet scheduler filter, from Cong Wang.
13) Add GRE tunnel support for mlxsw Spectrum-2, from Nir Dotan.
14) Lots of new IP tunneling forwarding tests, also from Nir Dotan.
15) Add 3ad stats to bonding, from Nikolay Aleksandrov.
16) Lots of probing improvements for bpftool, from Quentin Monnet.
17) Various nfp drive #ebpf JIT improvements from Jakub Kicinski.
18) Allow #ebpf programs to access gso_segs from skb shared info, from
Eric Dumazet.
19) Add sock_diag support for AF_XDP sockets, from Björn Töpel.
20) Support 22260 iwlwifi devices, from Luca Coelho.
21) Use rbtree for ipv6 defragmentation, from Peter Oskolkov.
22) Add JMP32 instruction class support to #ebpf, from Jiong Wang.
23) Add spinlock support to #ebpf, from Alexei Starovoitov.
24) Support 256-bit keys and TLS 1.3 in ktls, from Dave Watson.
25) Add device infomation API to devlink, from Jakub Kicinski.
26) Add new timestamping socket options which are y2038 safe, from
Deepa Dinamani.
27) Add RX checksum offloading for various sh_eth chips, from Sergei
Shtylyov.
28) Flow offload infrastructure, from Pablo Neira Ayuso.
29) Numerous cleanups, improvements, and bug fixes to the PHY layer
and many drivers from Heiner Kallweit.
30) Lots of changes to try and make packet scheduler classifiers run
lockless as much as possible, from Vlad Buslov.
31) Support BCM957504 chip in bnxt_en driver, from Erik Burrows.
32) Add concurrency tests to tc-tests infrastructure, from Vlad
Buslov.
33) Add hwmon support to aquantia, from Heiner Kallweit.
34) Allow 64-bit values for SO_MAX_PACING_RATE, from Eric Dumazet.
And I would be remiss if I didn't thank the various major networking
subsystem maintainers for integrating much of this work before I even
saw it. Alexei Starovoitov, Daniel Borkmann, Pablo Neira Ayuso,
Johannes Berg, Kalle Valo, and many others. Thank you!"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2207 commits)
net/sched: avoid unused-label warning
net: ignore sysctl_devconf_inherit_init_net without SYSCTL
phy: mdio-mux: fix Kconfig dependencies
net: phy: use phy_modify_mmd_changed in genphy_c45_an_config_aneg
net: dsa: mv88e6xxx: add call to mv88e6xxx_ports_cmode_init to probe for new DSA framework
selftest/net: Remove duplicate header
sky2: Disable MSI on Dell Inspiron 1545 and Gateway P-79
net/mlx5e: Update tx reporter status in case channels were successfully opened
devlink: Add support for direct reporter health state update
devlink: Update reporter state to error even if recover aborted
sctp: call iov_iter_revert() after sending ABORT
team: Free BPF filter when unregistering netdev
ip6mr: Do not call __IP6_INC_STATS() from preemptible context
isdn: mISDN: Fix potential NULL pointer dereference of kzalloc
net: dsa: mv88e6xxx: support in-band signalling on SGMII ports with external PHYs
cxgb4/chtls: Prefix adapter flags with CXGB4
net-sysfs: Switch to bitmap_zalloc()
mellanox: Switch to bitmap_zalloc()
bpf: add test cases for non-pointer sanitiation logic
mlxsw: i2c: Extend initialization by querying resources data
...
A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
- Support for inter-word delays.
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects.
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlx9WtETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DfrB/92O47HJfHg1xIgOp4BLzT8lA5zQEsy
a8ApcLVLvY6mSfbB/G7RosfoPwTc1eZP5Q2BqzQOBIO+507ao4AcASARmkTwjwkC
eRUJ/THkGyGurs8POtnc5YJlHsT1t743QpqlUNekt+NqognlkPccgc5bNgixfuPD
eVSwVC85SKP3gCpAjVb6FFFmlWr8AKdlgx+41h9QpMNG/85H6xgo4C4Wlajt42/E
wNx+WXzlPyzB5Lc3IGPeF/I/Hu/Ta3hUZLTVpWi5ubM8p4SYGmMZ9l8sURPCz1pK
UMZFpJxx8DWwkj2F/FkoLasfiRqUHIP9K7NfKF0u2xdNbhEk1GA3NAG0
=ctKG
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
Summary:
- Support for inter-word delays
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum"
* tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (104 commits)
spi: sh-msiof: Restrict bits per word to 8/16/24/32 on R-Car Gen2/3
spi: sifive: Remove redundant dev_err call in sifive_spi_probe()
spi: sifive: Remove spi_master_put in sifive_spi_remove()
spi: spi-gpio: fix SPI_CS_HIGH capability
spi: pxa2xx: Setup maximum supported DMA transfer length
spi: sifive: Add driver for the SiFive SPI controller
spi: sifive: Add DT documentation for SiFive SPI controller
spi: sprd: Add a prefix for SPI DMA channel macros
spi: sprd: spi: sprd: Add DMA mode support
dt-bindings: spi: Add the DMA properties for the SPI dma mode
spi: sprd: Add the SPI irq function for the SPI DMA mode
dt-bindings: spi: imx: Add an entry for the i.MX8QM compatible
spi: use gpio[d]_set_value_cansleep for setting chipselect GPIO
spi: gpio: Advertise support for SPI_CS_HIGH
spi: sh-msiof: Replace spi_master by spi_controller
spi: sh-hspi: Replace spi_master by spi_controller
spi: rspi: Replace spi_master by spi_controller
spi: atmel-quadspi: add support for sam9x60 qspi controller
dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60
spi: atmel-quadspi: add support for named peripheral clock
...
Every in-kernel use of this function defined it to KERNEL_DS (either as
an actual define, or as an inline function). It's an entirely
historical artifact, and long long long ago used to actually read the
segment selector valueof '%ds' on x86.
Which in the kernel is always KERNEL_DS.
Inspired by a patch from Jann Horn that just did this for a very small
subset of users (the ones in fs/), along with Al who suggested a script.
I then just took it to the logical extreme and removed all the remaining
gunk.
Roughly scripted with
git grep -l '(get_ds())' -- :^tools/ | xargs sed -i 's/(get_ds())/(KERNEL_DS)/'
git grep -lw 'get_ds' -- :^tools/ | xargs sed -i '/^#define get_ds()/d'
plus manual fixups to remove a few unusual usage patterns, the couple of
inline function cases and to fix up a comment that had become stale.
The 'get_ds()' function remains in an x86 kvm selftest, since in user
space it actually does something relevant.
Inspired-by: Jann Horn <jannh@google.com>
Inspired-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This commit rearranges the HUB interrupt code by using MIPS_IRQ_CPU
interrupt handling code and modern Linux IRQ framework features to get
rid of global arrays. It also adds support for irq affinity setting.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
To make use of per_cpu variables in interrupt code per_cpu_init() must
be done after setup_per_cpu_areas(). This is achieved by calling it
in smp_prepare_boot_cpu() via a new smp_ops method.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Introduced bridge_read/bridge_write/bridge_set/bridge_clr for accessing
bridge register and get rid of volatile declarations. Also removed
all typedefs from arch/mips/include/asm/pci/bridge.h and cleaned up
language in arch/mips/pci/ops-bridge.c
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Replace hub register access with __raw_readq/__raw_writeq and get
rid of hubreg_t completely. Also remove no longer (probably never
used) used defines
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
The netfilter conflicts were rather simple overlapping
changes.
However, the cls_tcindex.c stuff was a bit more complex.
On the 'net' side, Cong is fixing several races and memory
leaks. Whilst on the 'net-next' side we have Vlad adding
the rtnl-ness support.
What I've decided to do, in order to resolve this, is revert the
conversion over to using a workqueue that Cong did, bringing us back
to pure RCU. I did it this way because I believe that either Cong's
races don't apply with have Vlad did things, or Cong will have to
implement the race fix slightly differently.
Signed-off-by: David S. Miller <davem@davemloft.net>
Program rx/tx-delay always from DT.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Commit 46011e6ea3 ("MIPS: Make set_pte() SMP safe.") introduced an
open-coded version of cmpxchg() within set_pte(), that always operated
on a value the size of an unsigned long. That is, it used ll/sc
instructions when CONFIG_32BIT=y or lld/scd instructions when
CONFIG_64BIT=y.
This was broken for configurations in which pte_t is larger than an
unsigned long (with the exception of XPA configurations which have a
different implementation of set_pte()), because we no longer update the
whole PTE. Indeed commit 46011e6ea3 ("MIPS: Make set_pte() SMP safe.")
notes:
> The case of CONFIG_64BIT_PHYS_ADDR && CONFIG_CPU_MIPS32 is *not*
> handled.
In practice this affects Netlogic XLR/XLS systems including
nlm_xlr_defconfig.
Commit 82f4f66ddf ("MIPS: Remove open-coded cmpxchg() in set_pte()")
then replaced this open-coded version of cmpxchg() with an actual call
to cmpxchg(). Unfortunately the configurations mentioned above then fail
to build because cmpxchg() can only operate on values 32 bits or smaller
in size, resulting in:
arch/mips/include/asm/cmpxchg.h:166:11: error:
call to '__cmpxchg_called_with_bad_pointer' declared with
attribute error: Bad argument size for cmpxchg
One option that would fix the build failure & restore the previous
behaviour would be to cast the pte pointer to a pointer to unsigned
long, so that cmpxchg() would operate on just 32 bits of the PTE as it
has been since commit 46011e6ea3 ("MIPS: Make set_pte() SMP safe.").
That feels like an ugly hack though, and the behaviour of set_pte() is
likely a little broken.
Instead we take advantage of the fact that the affected configurations
already know at compile time that the CPU will support 64 bits (ie. have
hardcoded cpu_has_64bits in cpu-feature-overrides.h) in order to allow
cmpxchg64() to be used in these configurations. set_pte() then makes use
of cmpxchg64() when necessary.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Fixes: 46011e6ea3 ("MIPS: Make set_pte() SMP safe.")
Fixes: 82f4f66ddf ("MIPS: Remove open-coded cmpxchg() in set_pte()")
set_pte() contains an open coded version of cmpxchg() - it atomically
replaces the buddy pte's value if it is currently zero. Simplify the
code considerably by just using cmpxchg() instead of reinventing it.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Introduce support for using MemoryMapIDs (MMIDs) as an alternative to
Address Space IDs (ASIDs). The major difference between the two is that
MMIDs are global - ie. an MMID uniquely identifies an address space
across all coherent CPUs. In contrast ASIDs are non-global per-CPU IDs,
wherein each address space is allocated a separate ASID for each CPU
upon which it is used. This global namespace allows a new GINVT
instruction be used to globally invalidate TLB entries associated with a
particular MMID across all coherent CPUs in the system, removing the
need for IPIs to invalidate entries with separate ASIDs on each CPU.
The allocation scheme used here is largely borrowed from arm64 (see
arch/arm64/mm/context.c). In essence we maintain a bitmap to track
available MMIDs, and MMIDs in active use at the time of a rollover to a
new MMID version are preserved in the new version. The allocation scheme
requires efficient 64 bit atomics in order to perform reasonably, so
this support depends upon CONFIG_GENERIC_ATOMIC64=n (ie. currently it
will only be included in MIPS64 kernels).
The first, and currently only, available CPU with support for MMIDs is
the MIPS I6500. This CPU supports 16 bit MMIDs, and so for now we cap
our MMIDs to 16 bits wide in order to prevent the bitmap growing to
absurd sizes if any future CPU does implement 32 bit MMIDs as the
architecture manuals suggest is recommended.
When MMIDs are in use we also make use of GINVT instruction which is
available due to the global nature of MMIDs. By executing a sequence of
GINVT & SYNC 0x14 instructions we can avoid the overhead of an IPI to
each remote CPU in many cases. One complication is that GINVT will
invalidate wired entries (in all cases apart from type 0, which targets
the entire TLB). In order to avoid GINVT invalidating any wired TLB
entries we set up, we make sure to create those entries using a reserved
MMID (0) that we never associate with any address space.
Also of note is that KVM will require further work in order to support
MMIDs & GINVT, since KVM is involved in allocating IDs for guests & in
configuring the MMU. That work is not part of this patch, so for now
when MMIDs are in use KVM is disabled.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Add a family of ginvt_* functions making it easy to emit a GINVT
instruction to globally invalidate TLB entries. We make use of the
_ASM_MACRO infrastructure to support emitting the instructions even if
the assembler isn't new enough to support them natively.
An associated STYPE_GINV definition & sync_ginv() function are added to
emit a sync instruction of type 0x14, which operates as a completion
barrier for these new GINVT (and GINVI) instructions.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
When we gain MMID support we'll be storing MMIDs as atomic64_t values
and accessing them via atomic64_* functions. This necessitates that we
don't use cpu_context() as the left hand side of an assignment, ie. as a
modifiable lvalue. In preparation for this introduce a new
set_cpu_context() function & replace all assignments with cpu_context()
on their left hand side with an equivalent call to set_cpu_context().
To enforce that cpu_context() should not be used for assignments, we
rewrite it as a static inline function.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Introduce a new check_mmu_context() function to check an mm's ASID
version & get a new one if it's outdated, and a
check_switch_mmu_context() function which additionally sets up the new
ASID & page directory. Simplify switch_mm() & various
get_new_mmu_context() callsites in MIPS KVM by making use of the new
functions, which will help reduce the amount of code that requires
modification to gain MMID support.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
In preparation for adding MMID support to get_new_mmu_context() which
will increase the size of the function somewhat, move it from
asm/mmu_context.h into a C file.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
All 3 variants of local_flush_tlb_mm() are now effectively simple calls
to drop_mmu_context(). Remove them and use drop_mmu_context() directly.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
drop_mmu_context() is preceded by a comment indicating what happens if
the mm provided is currently active on the local CPU. Move that comment
into the block that executes in this case, adjusting slightly to reflect
its new location.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
If an mm does not have an ASID on the local CPU then drop_mmu_context()
is always redundant, since there's no context to "drop". Various callers
of drop_mmu_context() check whether the mm has been allocated an ASID
before making the call. Move that check into drop_mmu_context() and
remove it from callers to simplify them.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
If drop_mmu_context() is called with an mm that is not currently active
on the local CPU then there's no need for us to stop & start a hardware
page table walker because it can't be fetching entries for the ASID
corresponding to the mm we're operating on.
Move the htw_stop() & htw_start() calls into the block which we run only
if the mm is currently active, in order to avoid the redundant work.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
get_new_mmu_context() accepts a cpu argument, but implicitly assumes
that this is always equal to smp_processor_id() by operating on the
local CPU's TLB & icache.
Remove the cpu argument and have get_new_mmu_context() call
smp_processor_id() instead.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
The drop_mmu_context() function accepts a cpu argument, but it
implicitly expects that this is always equal to smp_processor_id() by
allocating & configuring an ASID on the local CPU when the mm is active
on the CPU indicated by the cpu argument.
All callers do provide the value of smp_processor_id() to the cpu
argument.
Remove the redundant argument and have drop_mmu_context() call
smp_processor_id() itself, making it clearer that the cpu variable
always represents the local CPU.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
MIPS has separate definitions of activate_mm() & switch_mm() which are
identical apart from switch_mm() checking that the ASID is valid before
acquiring a new one.
We know that when activate_mm() is called cpu_context(X, mm) will be
zero, and this will never be considered a valid ASID because we never
allow the ASID version number to be zero, instead beginning with version
1 using asid_first_version(). Therefore switch_mm() will always allocate
a new ASID when called for a new task, meaning that it will behave
identically to activate_mm().
Take advantage of this to remove the duplication & define activate_mm()
using switch_mm() just like many other architectures do.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
On the Loongson-2G/2H/3A/3B there is a hardware flaw that ll/sc and
lld/scd is very weak ordering. We should add sync instructions "before
each ll/lld" and "at the branch-target between ll/sc" to workaround.
Otherwise, this flaw will cause deadlock occasionally (e.g. when doing
heavy load test with LTP).
Below is the explaination of CPU designer:
"For Loongson 3 family, when a memory access instruction (load, store,
or prefetch)'s executing occurs between the execution of LL and SC, the
success or failure of SC is not predictable. Although programmer would
not insert memory access instructions between LL and SC, the memory
instructions before LL in program-order, may dynamically executed
between the execution of LL/SC, so a memory fence (SYNC) is needed
before LL/LLD to avoid this situation.
Since Loongson-3A R2 (3A2000), we have improved our hardware design to
handle this case. But we later deduce a rarely circumstance that some
speculatively executed memory instructions due to branch misprediction
between LL/SC still fall into the above case, so a memory fence (SYNC)
at branch-target (if its target is not between LL/SC) is needed for
Loongson 3A1000, 3B1500, 3A2000 and 3A3000.
Our processor is continually evolving and we aim to to remove all these
workaround-SYNCs around LL/SC for new-come processor."
Here is an example:
Both cpu1 and cpu2 simutaneously run atomic_add by 1 on same atomic var,
this bug cause both 'sc' run by two cpus (in atomic_add) succeed at same
time('sc' return 1), and the variable is only *added by 1*, sometimes,
which is wrong and unacceptable(it should be added by 2).
Why disable fix-loongson3-llsc in compiler?
Because compiler fix will cause problems in kernel's __ex_table section.
This patch fix all the cases in kernel, but:
+. the fix at the end of futex_atomic_cmpxchg_inatomic is for branch-target
of 'bne', there other cases which smp_mb__before_llsc() and smp_llsc_mb() fix
the ll and branch-target coincidently such as atomic_sub_if_positive/
cmpxchg/xchg, just like this one.
+. Loongson 3 does support CONFIG_EDAC_ATOMIC_SCRUB, so no need to touch
edac.h
+. local_ops and cmpxchg_local should not be affected by this bug since
only the owner can write.
+. mips_atomic_set for syscall.c is deprecated and rarely used, just let
it go
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Huang Pei <huangpei@loongson.cn>
[paul.burton@mips.com:
- Simplify the addition of -mno-fix-loongson3-llsc to cflags, and add
a comment describing why it's there.
- Make loongson_llsc_mb() a no-op when
CONFIG_CPU_LOONGSON3_WORKAROUNDS=n, rather than a compiler memory
barrier.
- Add a comment describing the bug & how loongson_llsc_mb() helps
in asm/barrier.h.]
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: ambrosehua@gmail.com
Cc: Steven J . Hill <Steven.Hill@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: Li Xuefeng <lixuefeng@loongson.cn>
Cc: Xu Chenghua <xuchenghua@loongson.cn>
SO_RCVTIMEO and SO_SNDTIMEO socket options use struct timeval
as the time format. struct timeval is not y2038 safe.
The subsequent patches in the series add support for new socket
timeout options with _NEW suffix that will use y2038 safe
data structures. Although the existing struct timeval layout
is sufficiently wide to represent timeouts, because of the way
libc will interpret time_t based on user defined flag, these
new flags provide a way of having a structure that is the same
for all architectures consistently.
Rename the existing options with _OLD suffix forms so that the
right option is enabled for userspace applications according
to the architecture and time_t definition of libc.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Cc: ccaulfie@redhat.com
Cc: deller@gmx.de
Cc: paulus@samba.org
Cc: ralf@linux-mips.org
Cc: rth@twiddle.net
Cc: cluster-devel@redhat.com
Cc: linuxppc-dev@lists.ozlabs.org
Cc: linux-alpha@vger.kernel.org
Cc: linux-arch@vger.kernel.org
Cc: linux-mips@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Cc: sparclinux@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
This line is weird in multiple ways.
(CONFIG_GENERIC_CSUM) might be a typo of $(CONFIG_GENERIC_CSUM).
Even if you add '$' to it, $(CONFIG_GENERIC_CSUM) is never evaluated
to 'y' because scripts/Makefile.asm-generic does not include
include/config/auto.conf. So, the asm-generic wrapper of checksum.h
is never generated.
Even if you manage to generate it, it is never included by anyone
because MIPS has the checkin header with the same file name:
arch/mips/include/asm/checksum.h
As you see in the top Makefile, the checkin headers are included before
generated ones.
LINUXINCLUDE := \
-I$(srctree)/arch/$(SRCARCH)/include \
-I$(objtree)/arch/$(SRCARCH)/include/generated \
...
Commit 4e0748f5be ("MIPS: Use generic checksum functions for MIPS R6")
already added the asm-generic fallback code in the checkin header:
#ifdef CONFIG_GENERIC_CSUM
#include <asm/generic/checksum.h>
#else
...
#endif
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: linux-kernel@vger.kernel.org
GS232 core used in Loongson-1 processors has a bug that
di instruction doesn't save the irqflag immediately.
Workaround by set irqflag in CP0 before di instructions
as same as Loongson-3.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: keguang.zhang@gmail.com
With the target now being fully OF based, we can drop the legacy IRQ code.
All IRQs are now handled via the new irqchip drivers.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: linux-mips@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: Felix Fietkau <nbd@nbd.name>
platform.c contains several unused platform device with no
drivers submited.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: keguang.zhang@gmail.com
This introduces a new generic SOL_SOCKET-level socket option called
SO_BINDTOIFINDEX. It behaves similar to SO_BINDTODEVICE, but takes a
network interface index as argument, rather than the network interface
name.
User-space often refers to network-interfaces via their index, but has
to temporarily resolve it to a name for a call into SO_BINDTODEVICE.
This might pose problems when the network-device is renamed
asynchronously by other parts of the system. When this happens, the
SO_BINDTODEVICE might either fail, or worse, it might bind to the wrong
device.
In most cases user-space only ever operates on devices which they
either manage themselves, or otherwise have a guarantee that the device
name will not change (e.g., devices that are UP cannot be renamed).
However, particularly in libraries this guarantee is non-obvious and it
would be nice if that race-condition would simply not exist. It would
make it easier for those libraries to operate even in situations where
the device-name might change under the hood.
A real use-case that we recently hit is trying to start the network
stack early in the initrd but make it survive into the real system.
Existing distributions rename network-interfaces during the transition
from initrd into the real system. This, obviously, cannot affect
devices that are up and running (unless you also consider moving them
between network-namespaces). However, the network manager now has to
make sure its management engine for dormant devices will not run in
parallel to these renames. Particularly, when you offload operations
like DHCP into separate processes, these might setup their sockets
early, and thus have to resolve the device-name possibly running into
this race-condition.
By avoiding a call to resolve the device-name, we no longer depend on
the name and can run network setup of dormant devices in parallel to
the transition off the initrd. The SO_BINDTOIFINDEX ioctl plugs this
race.
Reviewed-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow building this driver in compile test we need to remove all
dependency on headers from arch/mips/include. To allow this we
explicitly define all the registers locally instead of using
ar71xx_regs.h and we move the platform data struct definition to
include/linux/platform_data/spi-ath79.h.
Signed-off-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of using the lantiq specific MIPS_CPU_TIMER_IRQ use the generic
CP0_LEGACY_COMPARE_IRQ constant for the timer interrupt number.
MIPS_CPU_TIMER_IRQ was already defined to 7 for both supported SoC
families.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: jhogan@kernel.org
Cc: ralf@linux-mips.org
Cc: john@phrozen.org
Cc: linux-mips@linux-mips.org
Cc: linux-mips@vger.kernel.org
Now that Kbuild automatically creates asm-generic wrappers for missing
mandatory headers, it is redundant to list the same headers in
generic-y and mandatory-y.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
These comments are leftovers of commit fcc8487d47 ("uapi: export all
headers under uapi directories").
Prior to that commit, exported headers must be explicitly added to
header-y. Now, all headers under the uapi/ directories are exported.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
- The Broadcom BCM63xx platform sees a fix for resetting the BCM6368
ethernet switch, and the removal of a platform device we've never had
a driver for.
- The Alchemy platform sees a few fixes for bitrot that occurred within
the past few cycles.
- We now enable vectored interrupt support for the MediaTek MT7620 SoC,
which makes sense since they're supported by the SoC but in this case
also works around a bug relating to the location of exception vectors
when using a recent version of U-Boot.
- The atomic64_fetch_*_relaxed() family of functions see a fix for a
regression in MIPS64 kernels since v4.19.
- Cavium Octeon III CN7xxx systems will now disable their RGMII
interfaces rather than attempt to enable them & warn about the lack of
support for doing so, as they did since initial CN7xxx ethernet
support was added in v4.7.
- The Microsemi/Microchip MSCC SoCs gain a MAINTAINERS entry.
- .mailmap now provides consistency for Dengcheng Zhu's name & current
email address.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXDEVXBUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN2F4QEA5lJSa7x2ZMjV/z/P174lotgsclrp
EtcIf/Jx3IekXmsA/0LhuuC+6l7bq1DJRolsgeuhPTRBUM+8lvs8KXDVhzsA
=ImMx
-----END PGP SIGNATURE-----
Merge tag 'mips_fixes_4.21_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS fixes from Paul Burton:
"A few early MIPS fixes for 4.21:
- The Broadcom BCM63xx platform sees a fix for resetting the BCM6368
ethernet switch, and the removal of a platform device we've never
had a driver for.
- The Alchemy platform sees a few fixes for bitrot that occurred
within the past few cycles.
- We now enable vectored interrupt support for the MediaTek MT7620
SoC, which makes sense since they're supported by the SoC but in
this case also works around a bug relating to the location of
exception vectors when using a recent version of U-Boot.
- The atomic64_fetch_*_relaxed() family of functions see a fix for a
regression in MIPS64 kernels since v4.19.
- Cavium Octeon III CN7xxx systems will now disable their RGMII
interfaces rather than attempt to enable them & warn about the lack
of support for doing so, as they did since initial CN7xxx ethernet
support was added in v4.7.
- The Microsemi/Microchip MSCC SoCs gain a MAINTAINERS entry.
- .mailmap now provides consistency for Dengcheng Zhu's name &
current email address"
* tag 'mips_fixes_4.21_1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux:
MIPS: OCTEON: mark RGMII interface disabled on OCTEON III
MIPS: Fix a R10000_LLSC_WAR logic in atomic.h
MIPS: BCM63XX: drop unused and broken DSP platform device
mailmap: Update name spelling and email for Dengcheng Zhu
MIPS: ralink: Select CONFIG_CPU_MIPSR2_IRQ_VI on MT7620/8
MAINTAINERS: Add a maintainer for MSCC MIPS SoCs
MIPS: Alchemy: update dma masks for devboard devices
MIPS: Alchemy: update cpu-feature-overrides
MIPS: Alchemy: drop DB1000 IrDA support bits
MIPS: alchemy: cpu_all_mask is forbidden for clock event devices
MIPS: BCM63XX: fix switch core reset on BCM6368
Merge more updates from Andrew Morton:
- procfs updates
- various misc bits
- lib/ updates
- epoll updates
- autofs
- fatfs
- a few more MM bits
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (58 commits)
mm/page_io.c: fix polled swap page in
checkpatch: add Co-developed-by to signature tags
docs: fix Co-Developed-by docs
drivers/base/platform.c: kmemleak ignore a known leak
fs: don't open code lru_to_page()
fs/: remove caller signal_pending branch predictions
mm/: remove caller signal_pending branch predictions
arch/arc/mm/fault.c: remove caller signal_pending_branch predictions
kernel/sched/: remove caller signal_pending branch predictions
kernel/locking/mutex.c: remove caller signal_pending branch predictions
mm: select HAVE_MOVE_PMD on x86 for faster mremap
mm: speed up mremap by 20x on large regions
mm: treewide: remove unused address argument from pte_alloc functions
initramfs: cleanup incomplete rootfs
scripts/gdb: fix lx-version string output
kernel/kcov.c: mark write_comp_data() as notrace
kernel/sysctl: add panic_print into sysctl
panic: add options to print system info when panic happens
bfs: extra sanity checking and static inode bitmap
exec: separate MM_ANONPAGES and RLIMIT_STACK accounting
...
Patch series "Add support for fast mremap".
This series speeds up the mremap(2) syscall by copying page tables at
the PMD level even for non-THP systems. There is concern that the extra
'address' argument that mremap passes to pte_alloc may do something
subtle architecture related in the future that may make the scheme not
work. Also we find that there is no point in passing the 'address' to
pte_alloc since its unused. This patch therefore removes this argument
tree-wide resulting in a nice negative diff as well. Also ensuring
along the way that the enabled architectures do not do anything funky
with the 'address' argument that goes unnoticed by the optimization.
Build and boot tested on x86-64. Build tested on arm64. The config
enablement patch for arm64 will be posted in the future after more
testing.
The changes were obtained by applying the following Coccinelle script.
(thanks Julia for answering all Coccinelle questions!).
Following fix ups were done manually:
* Removal of address argument from pte_fragment_alloc
* Removal of pte_alloc_one_fast definitions from m68k and microblaze.
// Options: --include-headers --no-includes
// Note: I split the 'identifier fn' line, so if you are manually
// running it, please unsplit it so it runs for you.
virtual patch
@pte_alloc_func_def depends on patch exists@
identifier E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
type T2;
@@
fn(...
- , T2 E2
)
{ ... }
@pte_alloc_func_proto_noarg depends on patch exists@
type T1, T2, T3, T4;
identifier fn =~ "^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1, T2);
+ T3 fn(T1);
|
- T3 fn(T1, T2, T4);
+ T3 fn(T1, T2);
)
@pte_alloc_func_proto depends on patch exists@
identifier E1, E2, E4;
type T1, T2, T3, T4;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
(
- T3 fn(T1 E1, T2 E2);
+ T3 fn(T1 E1);
|
- T3 fn(T1 E1, T2 E2, T4 E4);
+ T3 fn(T1 E1, T2 E2);
)
@pte_alloc_func_call depends on patch exists@
expression E2;
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
@@
fn(...
-, E2
)
@pte_alloc_macro depends on patch exists@
identifier fn =~
"^(__pte_alloc|pte_alloc_one|pte_alloc|__pte_alloc_kernel|pte_alloc_one_kernel)$";
identifier a, b, c;
expression e;
position p;
@@
(
- #define fn(a, b, c) e
+ #define fn(a, b) e
|
- #define fn(a, b) e
+ #define fn(a) e
)
Link: http://lkml.kernel.org/r/20181108181201.88826-2-joelaf@google.com
Signed-off-by: Joel Fernandes (Google) <joel@joelfernandes.org>
Suggested-by: Kirill A. Shutemov <kirill@shutemov.name>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: William Kucharski <william.kucharski@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When testing in userspace, UBSAN pointed out that shifting into the sign
bit is undefined behaviour. It doesn't really make sense to ask for the
highest set bit of a negative value, so just turn the argument type into
an unsigned int.
Some architectures (eg ppc) already had it declared as an unsigned int,
so I don't expect too many problems.
Link: http://lkml.kernel.org/r/20181105221117.31828-1-willy@infradead.org
Signed-off-by: Matthew Wilcox <willy@infradead.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 4936084c2e ("MIPS: Cleanup R10000_LLSC_WAR logic in atomic.h")
introduce a mistake in atomic64_fetch_##op##_relaxed(), because it
forget to delete R10000_LLSC_WAR in the if-condition. So fix it.
Fixes: 4936084c2e ("MIPS: Cleanup R10000_LLSC_WAR logic in atomic.h")
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Joshua Kinard <kumba@gentoo.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven J . Hill <Steven.Hill@cavium.com>
Cc: Fuxin Zhang <zhangfx@lemote.com>
Cc: Zhangjin Wu <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: stable@vger.kernel.org # 4.19+
Trying to register the DSP platform device results in a null pointer
access:
[ 0.124184] CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 804e305c, ra == 804e6f20
[ 0.135208] Oops[#1]:
[ 0.137514] CPU: 0 PID: 1 Comm: swapper Not tainted 4.14.87
...
[ 0.197117] epc : 804e305c bcm63xx_dsp_register+0x80/0xa4
[ 0.202838] ra : 804e6f20 board_register_devices+0x258/0x390
...
This happens because it tries to copy the passed platform data over the
platform_device's unpopulated platform_data.
Since this code has been broken since its submission, no driver was ever
submitted for it, and apparently nobody was using it, just remove it
instead of trying to fix it.
Fixes: e7300d04bd ("MIPS: BCM63xx: Add support for the Broadcom BCM63xx family of SOCs.")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: James Hogan <jhogan@kernel.org>
Linus Torvalds