This patch fixes an issue that we cannot use nfs rootfs correctly
on r8a7790 when the command below runs on a host PC.
$ sudo ping -f -l 8 $BOARD_IP_ADDR
Since the driver sets the RACT to 1 in the first while loop of
sh_eth_rx(), the controller accepts a next frame into the next RX
descriptor during the while loop. But, in the first while loop
doesn't allocate a next skb. So, this patch removes the RACT setting
in the first while loop of sh_eth_rx().
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the packet "exceeded" condition in sh_eth_rx() when
RACT in an RX descriptor is not set and the "quota" is 0.
Otherwise, kernel panic happens because the "&n->poll_list" is deleted
twice in sh_eth_poll() which calls napi_complete() and net_rx_action().
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix compiler warning on 32-bit architectures:
net/core/filter.c: In function '__sk_run_filter':
net/core/filter.c:540:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
net/core/filter.c:550:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
net/core/filter.c:560:22: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 4f4482dcd9 ("tipc: compensate
for double accounting in socket rcv buffer") we access 'truesize' of
a received buffer after it might have been released by the function
filter_rcv().
In this commit we correct this by reading the value of 'truesize' to
the stack before delivering the buffer to filter_rcv().
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SXGBE_CORE_L34_ADDCTL_REG define is cut and pasted twice so we can
delete the second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The QLC_83XX_GET_LSO_CAPABILITY define is cut and pasted twice so we can
delete the second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai says:
====================
cpumask,net: affinity hint helper function
This patchset will set affinity hint to influence IRQs to be allocated on the
same NUMA node as the one where the card resides. As discussed in
http://www.spinics.net/lists/netdev/msg271497.html
If number of IRQs allocated is greater than the number of local NUMA cores, all
local cores will be used first, and the rest of the IRQs will be on a remote
NUMA node.
If no NUMA support - IRQ's and cores will be mapped 1:1
Since the utility function to calculate the mapping could be useful in other mq
drivers in the kernel, it was added to cpumask.[ch]
This patchset was tested and applied on top of net-next since the first
consumer is a network device (mlx4_en). Over commit fff1f59 "mac802154:
llsec: add forgotten list_del_rcu in key removal"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The “affinity hint” mechanism is used by the user space
daemon, irqbalancer, to indicate a preferred CPU mask for irqs.
Irqbalancer can use this hint to balance the irqs between the
cpus indicated by the mask.
We wish the HCA to preferentially map the IRQs it uses to numa cores
close to it. To accomplish this, we use cpumask_set_cpu_local_first(), that
sets the affinity hint according the following policy:
First it maps IRQs to “close” numa cores. If these are exhausted, the
remaining IRQs are mapped to “far” numa cores.
Signed-off-by: Yuval Atias <yuvala@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function sets the n'th cpu - local cpu's first.
For example: in a 16 cores server with even cpu's local, will get the
following values:
cpumask_set_cpu_local_first(0, numa, cpumask) => cpu 0 is set
cpumask_set_cpu_local_first(1, numa, cpumask) => cpu 2 is set
...
cpumask_set_cpu_local_first(7, numa, cpumask) => cpu 14 is set
cpumask_set_cpu_local_first(8, numa, cpumask) => cpu 1 is set
cpumask_set_cpu_local_first(9, numa, cpumask) => cpu 3 is set
...
cpumask_set_cpu_local_first(15, numa, cpumask) => cpu 15 is set
Curently this function will be used by multi queue networking devices to
calculate the irq affinity mask, such that as many local cpu's as
possible will be utilized to handle the mq device irq's.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull thermal management update from Zhang Rui:
"Specifics:
- fix a bug in Exynos thermal driver, which overwrites the hardware
trip point threshold when updating software trigger levels and
results in emergency shutdown. From: Tushar Behera.
- add thermal sensor support for Armada 375 and 38x SoCs. From
Ezequiel Garcia.
- add TMU (Thermal Management Unit) support for Exynos5260 and
Exynos5420 SoCs. From Naveen Krishna Chatradhi.
- add support for the additional digital temperature sensors in the
Intel SoCs like Bay Trail. From: Srinivas Pandruvada.
- a couple of cleanups and small fixes from Jingoo Han, Bartlomiej
Zolnierkiewicz, Geert Uytterhoeven, Jacob Pan, Paul Walmsley and
Lan,Tianyu"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (21 commits)
thermal: spear: remove unnecessary OOM messages
thermal: exynos: remove unnecessary OOM messages
thermal: rcar: remove unnecessary OOM messages
thermal: armada: Support Armada 380 SoC
thermal: armada: Support Armada 375 SoC
thermal: armada: Allow to specify an 'inverted readout' sensor
thermal: armada: Pass the platform_device to init_sensor()
thermal: armada: Add generic infrastructure to handle the sensor
thermal: armada: Add infrastructure to support generic formulas
thermal: armada: Rename armada_thermal_ops struct
thermal/intel_powerclamp: add newer cpu ids
thermal: rcar: Use pm_runtime_put() i.s.o. pm_runtime_put_sync()
thermal: samsung: Only update available threshold limits
Thermal/int3403: Fix thermal hysteresis unit conversion
thermal: Intel SoC DTS thermal
thermal: samsung: Add TMU support for Exynos5260 SoCs
thermal: samsung: Add TMU support for Exynos5420 SoCs
thermal: samsung: change base_common to more meaningful base_second
thermal: samsung: replace inten_ bit fields with intclr_
thermal: offer Samsung thermal support only when ARCH_EXYNOS is defined
...
The majority of these changes are cleanups and fixes across all drivers.
Redundant error messages are removed and more PWM controllers set the
.can_sleep flag to signal that they can't be used in atomic context.
Support is added for the Broadcom Kona family of SoCs and the Intel LPSS
driver can now probe PCI devices in addition to ACPI devices. Upon shut-
down, the pwm-backlight driver will now power off the backlight. It also
uses the new descriptor-based GPIO API for more concise GPIO handling.
A large chunk of these changes also converts platforms to use the lookup
mechanism rather than relying on the global number space to reference
PWM devices. This is largely in preparation for more unification and
cleanups in future patches. Eventually it will allow the legacy PWM API
to be removed.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=BDxR
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"The majority of these changes are cleanups and fixes across all
drivers. Redundant error messages are removed and more PWM
controllers set the .can_sleep flag to signal that they can't be used
in atomic context.
Support is added for the Broadcom Kona family of SoCs and the Intel
LPSS driver can now probe PCI devices in addition to ACPI devices.
Upon shutdown, the pwm-backlight driver will now power off the
backlight. It also uses the new descriptor-based GPIO API for more
concise GPIO handling.
A large chunk of these changes also converts platforms to use the
lookup mechanism rather than relying on the global number space to
reference PWM devices. This is largely in preparation for more
unification and cleanups in future patches. Eventually it will allow
the legacy PWM API to be removed"
* tag 'pwm/for-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (38 commits)
pwm: fsl-ftm: set pwm_chip can_sleep flag
pwm: ab8500: Fix wrong value shift for disable/enable PWM
pwm: samsung: do not set manual update bit in pwm_samsung_config
pwm: lp3943: Set pwm_chip can_sleep flag
pwm: atmel: set pwm_chip can_sleep flag
pwm: mxs: set pwm_chip can_sleep flag
pwm: tiehrpwm: inline accessor functions
pwm: tiehrpwm: don't build PM related functions when not needed
pwm-backlight: retrieve configured PWM period
leds: leds-pwm: retrieve configured PWM period
ARM: pxa: hx4700: use PWM_LOOKUP to initialize struct pwm_lookup
ARM: shmobile: armadillo: use PWM_LOOKUP to initialize struct pwm_lookup
ARM: OMAP3: Beagle: use PWM_LOOKUP to initialize struct pwm_lookup
pwm: modify PWM_LOOKUP to initialize all struct pwm_lookup members
ARM: pxa: hx4700: initialize all the struct pwm_lookup members
ARM: OMAP3: Beagle: initialize all the struct pwm_lookup members
pwm: renesas-tpu: remove unused struct tpu_pwm_platform_data
ARM: shmobile: armadillo: initialize all struct pwm_lookup members
pwm: add period and polarity to struct pwm_lookup
pwm: twl: Really disable twl6030 PWMs
...
DM thinp already checks whether the discard_granularity of the data
device is a factor of the thin-pool block size. But when using the
dm-thin-pool's discard passdown support, DM thinp was not selecting the
max of the underlying data device's discard_granularity and the
thin-pool's block size.
Update set_discard_limits() to set discard_granularity to the max of
these values. This enables blkdev_issue_discard() to properly align the
discards that are sent to the DM thin device on a full block boundary.
As such each discard will now cover an entire DM thin-pool block and the
block will be reclaimed.
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Split the single per bio-prison lock by using per bucket locking. Per
bucket locking benefits both dm-thin and dm-cache targets by reducing
bio-prison lock contention.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This patch updates vhost_scsi_get_tag() to accept the combined
expected data transfer length + T10 PI bytes as the value passed
into target_submit_cmd().
This is required now that target-core logic in commit 14ef9200
expects to subtract se_cmd->prot_length from se_cmd->data_length.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In various areas of the code, it is assumed that
se_cmd->data_length describes pure data. In case
that protection information exists over the wire
(protect bits is are on) the target core re-calculates
the data length from the CDB and the backed device
block size (instead of each transport peeking in the cdb).
Modify loopback device to include protection information
in the transferred data length (like other scsi transports).
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case protection information exists over the wire
iscsi header data length is required to include it.
Use protection information aware scsi helpers to set
the correct transfer length.
In order to avoid breakage, remove iser transfer length
checks for each task as they are not always true and
somewhat redundant anyway.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case protection information exists on the wire
scsi transports should include it in the transfer
byte count (even if protection information does not
exist in the host memory space). This helper will
compute the total transfer length from the scsi
command data length and protection attributes.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This device uses function 1 as the PCIe requester ID.
This vendor has similar boards based on the same Marvell 88SE9235 chipset,
but this patch was only tested with the 642L.
Tested on ASUS Sabertooth 990FX (AMD).
Link: https://bugzilla.kernel.org/show_bug.cgi?id=42679
Signed-off-by: Jérôme Carretero <cJ-ko@zougloub.eu>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-06-11
This series contains updates to igb, i40e and i40evf.
Todd makes a change to igb to un-hide invariant returns by getting rid of
the E1000_SUCCESS define and converting those returns to return 0.
Jacob separates the hardware logic from the set function, so that we can
re-use it during a ptp_reset in igb. This enables the reset to return
functionality to the last know timestamp mode, rather than resetting the
value.
Ashish implements context flags for headwb and headwb_addr so that we
do not have to keep them always enabled.
Shannon updates the admin queue API for the new firmware, which adds
set_pf_content, nvm_config_read/write, replaces set_phy_reset with
set_phy_debug and removes nvm_read/write_reg_se. Cleans up the driver
to use the stored base_queue value since there is no need to read the
PCI register for the PF's base queue on every single transmit queue
enable and disable as we already have the value stored from reading
the capability features at startup.
Anjali changes the notion of source and destination for FD_SB in ethtool
to align i40e with other drivers. Adds flow director statistics to
the PF stats. Fixes a bug in ethtool for flow director drop packet
filter where the drop action comes down as a ring_cookie value, so allow
it as a special value that can be used to configure destination control.
Mitch fixes the i40evf to keep the driver from going down when it is
already in a down state. This prevents a CPU soft lock in napi_disable().
Also change the i40evf to check the admin queue error bits since the
firmware can indicate any admin queue error states to the driver via
some bits in the length registers.
Neerav separates out the DCB capability and enabled flags because currently
if the firmware reports DCB capability the driver enables
I40E_FLAG_DCB_ENABLED flag. When this flag is enabled the driver inserts
a tag when transmitting a packet from the port even if there are no DCB
traffic classes configured at the port. So by adding the additional flag,
I40E_FLAG_DCB_CAPABLE, that will be set when the DCB capability is present
and the existing enabled flag will only be set if there are more than one
traffic classes configured at the port.
Greg fixes the i40e driver to not automatically accept tagged packets by
default so that the system must request a VLAN tag packet filter to get
packets with that tag. Greg also converts i40e to use the in-kernel
ether_addr_copy() instead of mempcy().
Jesse removes the FTYPE field from the receive descriptor to match the
hardware implementation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
SCTP update
This set contains transport path selection improvements in
SCTP. Please see individual patches for details.
====================
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following sparse warning:
net/sctp/associola.c:1556:29: warning: incorrect type in initializer (different base types)
net/sctp/associola.c:1556:29: expected bool [unsigned] [usertype] preload
net/sctp/associola.c:1556:29: got restricted gfp_t
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function sctp_select_active_and_retran_path(), we walk the
transport list in order to look for the two most recently used
ACTIVE transports (trans_pri, trans_sec). In case we didn't find
anything ACTIVE, we currently just camp on a possibly PF or
INACTIVE transport that is primary path; this behavior actually
dates back to linux-history tree of the very early days of
lksctp, and can yield a behavior that chooses suboptimal
transport paths.
Instead, be a bit more clever by reusing and extending the
recently introduced sctp_trans_elect_best() handler. In case
both transports are evaluated to have the same score resulting
from their states, break the tie by looking at: 1) transport
patch error count 2) last_time_heard value from each transport.
This is analogous to Nishida's Quick Failover draft [1],
section 5.1, 3:
The sender SHOULD avoid data transmission to PF destinations.
When all destinations are in either PF or Inactive state,
the sender MAY either move the destination from PF to active
state (and transmit data to the active destination) or the
sender MAY transmit data to a PF destination. In the former
scenario, (i) the sender MUST NOT notify the ULP about the
state transition, and (ii) MUST NOT clear the destination's
error counter. It is recommended that the sender picks the
PF destination with least error count (fewest consecutive
timeouts) for data transmission. In case of a tie (multiple PF
destinations with same error count), the sender MAY choose the
last active destination.
Thus for sctp_select_active_and_retran_path(), we keep track of
the best, if any, transport that is in PF state and in case no
ACTIVE transport has been found (hence trans_{pri,sec} is NULL),
we select the best out of the three: current primary_path and
retran_path as well as a possible PF transport.
The secondary may still camp on the original primary_path as
before. The change in sctp_trans_elect_best() with a more fine
grained tie selection also improves at the same time path selection
for sctp_assoc_update_retran_path() in case of non-ACTIVE states.
[1] http://tools.ietf.org/html/draft-nishida-tsvwg-sctp-failover-05
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Be more precise in transport path selection and use ktime
helpers instead of jiffies to compare and pick the better
primary and secondary recently used transports. This also
avoids any side-effects during a possible roll-over, and
could lead to better path decision-making.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch just refactors and moves the code for the active
path selection into its own helper function outside of
sctp_assoc_control_transport() which is already big enough.
No functional changes here.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two minimal helper functions analogous to time_before() and
time_after() that will later on both be needed by SCTP code.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an initiator sends an allocation length bigger than what its
command consumes, the target should only return the actual response data
and set the residual length to the unused part of the allocation length.
Add a helper function that command handlers (INQUIRY, READ CAPACITY,
etc) can use to do this correctly, and use this code to get the correct
residual for commands that don't use the full initiator allocation in the
handlers for READ CAPACITY, READ CAPACITY(16), INQUIRY, MODE SENSE and
REPORT LUNS.
This addresses a handful of failures as reported by Christophe with
the Windows Certification Kit:
http://permalink.gmane.org/gmane.linux.scsi.target.devel/6515
Signed-off-by: Roland Dreier <roland@purestorage.com>
Tested-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Cc: stable@vger.kernel.org # 3.10+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Phoebe Buckheister says:
====================
Recent llsec code introduced a memory leak on decryption failures during rx.
This fixes said leak, and optimizes the receive loops for monitor and wpan
devices to only deliver skbs to devices that are actually up. Also changes a
dev_kfree_skb to kfree_skb when an invalid packet is dropped before being
pushed into the stack.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Only one WPAN devices can be active at any given time, so only deliver
packets to that one interface that is actually up. Multiple monitors may
be up at any given time, but we don't have to deliver to monitors that
are down either.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac802154 RX did not free skbs on decryption failure, assuming that the
caller would when the local rx handler returned _DROP. This was false.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
After relatively recent changes in the ACPI-based PCI hotplug
(ACPIPHP) code, the acpiphp_check_host_bridge() executed for PCI
host bridges via acpi_pci_root_scan_dependent() doesn't do anything
useful, because those bridges do not have hotplug contexts. That
happens by mistake, so fix it by making acpiphp_enumerate_slots()
add hotplug contexts to PCI host bridges too and modify
acpiphp_remove_slots() to drop those contexts for host bridges
as appropriate.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=76901
Fixes: 2d8b1d566a (ACPI / hotplug / PCI: Get rid of check_sub_bridges())
Reported-and-tested-by: Gavin Guo <gavin.guo@canonical.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch extracts LBA + sectors for VERIFY, and adds a goto check_lba
to perform the end-of-device checking.
(Update patch to drop lba_check usage - nab)
Signed-off-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A similar check is performed at the end of sbc_parse_cdb() and is now
enforced if the SYNCHRONIZE CACHE command's backend supports
->execute_sync_cache().
(Add check_lba goto to avoid *_max_sectors checks - nab)
Signed-off-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case the transport is iser we should not include the
iscsi target info in the sendtargets text response pdu.
This causes sendtargets response to include the target
info twice.
Modify iscsit_build_sendtargets_response to filter
transport types that don't match.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reported-by: Slava Shwartsman <valyushash@gmail.com>
Cc: stable@vger.kernel.org # 3.11+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
In case the discovery session is carried over iser, we can't
access the assumed network portal since the default portal is
used. In this case we don't really need to allocate the fastreg
pool, just prepare to the text pdu that will follow.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Reported-by: Alex Tabachnik <alext@mellanox.com>
Cc: stable@vger.kernel.org # 3.15+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This is a small follow-up to the larger ARM SoC updates merged
last week, almost entirely for the keystone platform.
The main change here is to use the new dma-ranges parsing code
that came in through Russell's ARM tree. This allows the keystone
platform to do cache-coherent DMA and to finally support all the
available physical memory when LPAE is enabled.
Aside from this, the keystone reset driver has been rewritten,
and there is a small bug fix to allow building the orion5x platform
again.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=AqkT
-----END PGP SIGNATURE-----
Merge tag 'soc2-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull part two of ARM SoC updates from Arnd Bergmann:
"This is a small follow-up to the larger ARM SoC updates merged last
week, almost entirely for the keystone platform.
The main change here is to use the new dma-ranges parsing code that
came in through Russell's ARM tree. This allows the keystone platform
to do cache-coherent DMA and to finally support all the available
physical memory when LPAE is enabled.
Aside from this, the keystone reset driver has been rewritten, and
there is a small bug fix to allow building the orion5x platform again"
* tag 'soc2-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: Drop use of meminfo since its not available anymore
ARM: orion5x: fix mvebu_mbus_dt_init call
ARM: configs: keystone: enable reset driver support
ARM: dts: keystone: update reset node to work with reset driver
ARM: keystone: remove redundant reset stuff
ARM: keystone: Update the dma offset for non-dt platform devices
ARM: keystone: Switch over to coherent memory address space
ARM: configs: keystone: add MTD_SPI_NOR (new dependency for M25P80)
ARM: configs: keystone: drop CONFIG_COMMON_CLK_DEBUG
Pull reiserfs and ext3 changes from Jan Kara:
"Big reiserfs cleanup from Jeff, an ext3 deadlock fix, and some small
cleanups"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs: (34 commits)
reiserfs: Fix compilation breakage with CONFIG_REISERFS_CHECK
ext3: Fix deadlock in data=journal mode when fs is frozen
reiserfs: call truncate_setsize under tailpack mutex
fs/jbd/revoke.c: replace shift loop by ilog2
reiserfs: remove obsolete __constant_cpu_to_le32
reiserfs: balance_leaf refactor, split up balance_leaf_when_delete
reiserfs: balance_leaf refactor, format balance_leaf_finish_node
reiserfs: balance_leaf refactor, format balance_leaf_new_nodes_paste
reiserfs: balance_leaf refactor, format balance_leaf_paste_right
reiserfs: balance_leaf refactor, format balance_leaf_insert_right
reiserfs: balance_leaf refactor, format balance_leaf_paste_left
reiserfs: balance_leaf refactor, format balance_leaf_insert_left
reiserfs: balance_leaf refactor, pull out balance_leaf{left, right, new_nodes, finish_node}
reiserfs: balance_leaf refactor, pull out balance_leaf_finish_node_paste
reiserfs: balance_leaf refactor pull out balance_leaf_finish_node_insert
reiserfs: balance_leaf refactor, pull out balance_leaf_new_nodes_paste
reiserfs: balance_leaf refactor, pull out balance_leaf_new_nodes_insert
reiserfs: balance_leaf refactor, pull out balance_leaf_paste_right
reiserfs: balance_leaf refactor, pull out balance_leaf_insert_right
reiserfs: balance_leaf refactor, pull out balance_leaf_paste_left
...
free_msi_irqs() is leaking memory, since list_for_each_entry(entry,
&dev->msi_list, list) {...} is never executed, because dev->msi_list is
made empty by the loop just above this one.
Fix it by relying on zero termination of attribute array like
populate_msi_sysfs() does.
Fixes: 1c51b50c29 ("PCI/MSI: Export MSI mode using attributes, not kobjects")
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: stable@vger.kernel.org # v3.14+
Pull btrfs updates from Chris Mason:
"The biggest change here is Josef's rework of the btrfs quota
accounting, which improves the in-memory tracking of delayed extent
operations.
I had been working on Btrfs stack usage for a while, mostly because it
had become impossible to do long stress runs with slab, lockdep and
pagealloc debugging turned on without blowing the stack. Even though
you upgraded us to a nice king sized stack, I kept most of the
patches.
We also have some very hard to find corruption fixes, an awesome sysfs
use after free, and the usual assortment of optimizations, cleanups
and other fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs: (80 commits)
Btrfs: convert smp_mb__{before,after}_clear_bit
Btrfs: fix scrub_print_warning to handle skinny metadata extents
Btrfs: make fsync work after cloning into a file
Btrfs: use right type to get real comparison
Btrfs: don't check nodes for extent items
Btrfs: don't release invalid page in btrfs_page_exists_in_range()
Btrfs: make sure we retry if page is a retriable exception
Btrfs: make sure we retry if we couldn't get the page
btrfs: replace EINVAL with EOPNOTSUPP for dev_replace raid56
trivial: fs/btrfs/ioctl.c: fix typo s/substract/subtract/
Btrfs: fix leaf corruption after __btrfs_drop_extents
Btrfs: ensure btrfs_prev_leaf doesn't miss 1 item
Btrfs: fix clone to deal with holes when NO_HOLES feature is enabled
btrfs: free delayed node outside of root->inode_lock
btrfs: replace EINVAL with ERANGE for resize when ULLONG_MAX
Btrfs: fix transaction leak during fsync call
btrfs: Avoid trucating page or punching hole in a already existed hole.
Btrfs: update commit root on snapshot creation after orphan cleanup
Btrfs: ioctl, don't re-lock extent range when not necessary
Btrfs: avoid visiting all extent items when cloning a range
...
This update contains:
o cleanup removing unused function args
o rework of the filestreams allocator to use dentry cache parent lookups
o new on-disk free inode btree and optimised inode allocator
o various bug fixes
o rework of internal attribute API
o cleanup of superblock feature bit support to remove historic cruft
o more fixes and minor cleanups
o added a new directory/attribute geometry abstraction
o yet more fixes and minor cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=qnz2
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-3.16-rc1' of git://oss.sgi.com/xfs/xfs
Pull xfs updates from Dave Chinner:
"This update contains:
- cleanup removing unused function args
- rework of the filestreams allocator to use dentry cache parent
lookups
- new on-disk free inode btree and optimised inode allocator
- various bug fixes
- rework of internal attribute API
- cleanup of superblock feature bit support to remove historic cruft
- more fixes and minor cleanups
- added a new directory/attribute geometry abstraction
- yet more fixes and minor cleanups"
* tag 'xfs-for-linus-3.16-rc1' of git://oss.sgi.com/xfs/xfs: (86 commits)
xfs: fix xfs_da_args sparse warning in xfs_readdir
xfs: Fix rounding in xfs_alloc_fix_len()
xfs: tone down writepage/releasepage WARN_ONs
xfs: small cleanup in xfs_lowbit64()
xfs: kill xfs_buf_geterror()
xfs: xfs_readsb needs to check for magic numbers
xfs: block allocation work needs to be kswapd aware
xfs: remove redundant geometry information from xfs_da_state
xfs: replace attr LBSIZE with xfs_da_geometry
xfs: pass xfs_da_args to xfs_attr_leaf_newentsize
xfs: use xfs_da_geometry for block size in attr code
xfs: remove mp->m_dir_geo from directory logging
xfs: reduce direct usage of mp->m_dir_geo
xfs: move node entry counts to xfs_da_geometry
xfs: convert dir/attr btree threshold to xfs_da_geometry
xfs: convert m_dirblksize to xfs_da_geometry
xfs: convert m_dirblkfsbs to xfs_da_geometry
xfs: convert directory segment limits to xfs_da_geometry
xfs: convert directory db conversion to xfs_da_geometry
xfs: convert directory dablk conversion to xfs_da_geometry
...
No need to read the PCI register for the PF's base queue on every single Tx
queue enable and disable as we already have the value stored from reading
the capability features at startup.
Change-ID: Ic02fb622757742f43cb8269369c3d972d4f66555
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A drop action comes down as a ring_cookie value, so allow it as
a special value that can be used to configure destination control.
Also fix the output to filter read command accordingly.
Change-ID: I9956723cee42f3194885403317dd21ed4a151144
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add members to stat struct to keep track of Flow director ATR and
SideBand filter packet matches.
Change-ID: Ibbb31a53c7adcc2bb96991dd80565442a2f2513c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change drops the FTYPE field from the Rx descriptor, to
match the hardware implementation.
Change-ID: I66d31d2b43861da45e8ace4fb03df033abe88bab
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
FW can indicate any admin queue error states to the driver via some bits
in the length registers. Each time we process an admin queue message,
check these bits and log any errors we find. Since the VF really can't
do much, we just print the message and depend on the PF driver to clear
things up on our behalf.
Change-ID: I92bc6c53ce3b4400544e0ca19c5de2d27490bd0d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Linux gives us a function to copy Ethernet MAC addresses, let's use it.
Change-ID: I0c861900029ca5ea65a53ca39565852fb633f6fd
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the filter created by the firmware with the default MAC address it
reads out of the NVM storage and a promiscuous VLAN tag and replace it
with a filter that will not accept tagged packets by default. The system
must request a VLAN tag packet filter to get packets with that tag.
Change-ID: I119e6c3603a039bd68282ba31bf26f33a575490a
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the firmware reports DCB capability the driver enables
I40E_FLAG_DCB_ENABLED flag. When this flag is enabled the driver
inserts a tag when transmitting a packet from the port even if there
are no DCB traffic classes configured at the port.
This patch adds a new flag I40E_FLAG_DCB_CAPABLE that will be set
when the DCB capability is present and the existing flag
I40E_FLAG_DCB_ENABLED will be set only if there are more than one
traffic classes configured at the port.
Change-ID: I24ccbf53ef293db2eba80c8a9772acf729795bd5
Signed-off-by: Neerav Parikh <neerav.parikh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the device is down, there's no place to go but up, so don't try to go
down even more. This prevents a CPU soft lock in napi_disable().
Change-ID: I8b058b9ee974dfa01c212fae2597f4f54b333314
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Yoshihiro Shimoda