Commit Graph

22 Commits

Author SHA1 Message Date
Lothar Waßmann 4191c34011 ARM: dts: mxs: modify mx23/mx28 dts files to use padconfig defines
Convert mx23/mx28 dts files to use the padconfig defintions from
mxs-pinfunc.h.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-09-26 13:01:37 +08:00
Lothar Waßmann bc3875f1a6 ARM: dts: mxs: modify mx23/mx28 dts files to use pinctrl headers
Convert mx23/mx28 dts filed to use the pinctrl header files.

NOTE: During automatic conversion of these files to use the pinconfig
definitions an inconsistency has been found in:
arch/arm/boot/dts/imx28-apx4devkit.dts

According to the comment the function for pad SSP2_SS0 should have
been MX28_PAD_SSP2_SS0__GPIO_2_19, while the given value 0x2131
represents: MX28_PAD_SSP2_SS0__AUART3_TX

I used the later (though probably wrong) definition because that's
what is actually being used in the DTB.

Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-09-26 13:01:36 +08:00
Alexandre Belloni dac63a5f1a ARM: mxs: dt: cfa10049: make hogpins grabbed by respective drivers
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-08-16 16:26:37 +08:00
Brian Lilly 65bc642f1b ARM: cfa10049: Switch the chip select pin of the LCD controller
The early prototypes had the chip select pin for the LCD controller
wired on the GPIO 3-23, while the production run of the CFA-10049 have
this chip select on the GPIO 3-5.

Signed-off-by: Brian Lilly <brian@crystalfontz.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17 15:43:30 +08:00
Maxime Ripard b400932c29 ARM: dts: cfa10036: Change the OLED display to SSD1306
The SSD1307 was used in an early prototype that will never get
distributed. The final board now has a SSD1306 instead, that has its own
power generation unit and thus doesn't need any PWM. The panel attached
to it also changed.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-06-17 15:43:28 +08:00
Alexandre Belloni ac77bc227e ARM: dts: cfa10036: Add touchscreen support to the CFA-10049
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-04-07 14:18:32 +08:00
Alexandre Belloni 7d40340864 ARM: cfa10036: add one wire bitbanging to the cfa10049
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-04-04 21:22:42 +08:00
Shawn Guo 0d9f8217db ARM: mxs: move display timing configurations into device tree
Move display timing configurations into device tree, so that the
auxdata for mxsfb driver can be killed.

Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-04-04 21:22:42 +08:00
Maxime Ripard 0943b96058 ARM: mxs: dts: Add rotary encoder to the CFA-10049
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-01-31 22:31:19 +08:00
Maxime Ripard a640cf64ff ARM: mxs: dts: Add gpio-keys for the rotary to the CFA-10049
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-01-31 22:31:11 +08:00
Maxime Ripard 1fe4274045 ARM: dts: mxs: Add the LCD to the 10049 board
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-01-29 18:23:25 +08:00
Maxime Ripard 7ecc70a98c ARM: dts: cfa10049: Change the SPI3 bus to spi-gpio
The DAC found on the last chip select requires a word length of 12 bits,
which is not supported by the SSP controller of the iMX28. Use
bitbanging for that bus to support such a length.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2013-01-29 15:38:59 +08:00
Maxime Ripard 5b615fbf4a ARM: dts: cfa10049: Add PCA9555 GPIO expander to the device tree
Add the GPIO expander found on the i2c1 bus, behind the muxer to the
device tree.

This gpio expander will be used to get tachymeters values and data ready
interruptions from the nuvoton NAU7802 ADCs.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-12-28 19:07:37 +08:00
Linus Torvalds 752451f01c Merge branch 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux
Pull i2c-embedded changes from Wolfram Sang:
 - CBUS driver (an I2C variant)
 - continued rework of the omap driver
 - s3c2410 gets lots of fixes and gains pinctrl support
 - at91 gains DMA support
 - the GPIO muxer gains devicetree probing
 - typical fixes and additions all over

* 'i2c-embedded/for-next' of git://git.pengutronix.de/git/wsa/linux: (45 commits)
  i2c: omap: Remove the OMAP_I2C_FLAG_RESET_REGS_POSTIDLE flag
  i2c: at91: add dma support
  i2c: at91: change struct members indentation
  i2c: at91: fix compilation warning
  i2c: mxs: Do not disable the I2C SMBus quick mode
  i2c: mxs: Handle i2c DMA failure properly
  i2c: s3c2410: Remove recently introduced performance overheads
  i2c: ocores: Move grlib set/get functions into #ifdef CONFIG_OF block
  i2c: s3c2410: Add fix for i2c suspend/resume
  i2c: s3c2410: Fix code to free gpios
  i2c: i2c-cbus-gpio: introduce driver
  i2c: ocores: Add support for the GRLIB port of the controller and use function pointers for getreg and setreg functions
  i2c: ocores: Add irq support for sparc
  i2c: omap: Move the remove constraint
  ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
  i2c: s3c2410: do not special case HDMIPHY stuck bus detection
  i2c: s3c2410: use exponential back off while polling for bus idle
  i2c: s3c2410: do not generate STOP for QUIRK_HDMIPHY
  i2c: s3c2410: grab adapter lock while changing i2c clock
  i2c: s3c2410: Add support for pinctrl
  ...
2012-12-18 16:51:10 -08:00
Maxime Ripard 06e9eff129 ARM: dts: cfa10049: Add the i2c muxer buses to the CFA-10049
This will allow to add the 3 Nuvoton NAU7802 ADCs and the NXP PCA9555
GPIO expander eventually.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
2012-11-16 15:08:12 +01:00
Maxime Ripard 24196d5c59 ARM: dts: mxs: Add hog pins to Crystalfontz boards
Use a hog_pins pinctrl group to force the muxing of GPIOs used on the
Crystalfonz CFA10036 and CFA10049 boards.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-11-05 10:53:34 +08:00
Maxime Ripard db7a8946dc ARM: dts: cfa10049: Add the DH2228FV DAC to the DTS
There is no driver for it yet, so it will use spidev.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-11-02 09:51:52 +08:00
Maxime Ripard 8eec4b3117 ARM: dts: cfa10049: Add FEC to the CFA-10049 expansion board
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-10-15 15:44:39 +08:00
Maxime Ripard 13b4569bbb ARM: dts: cfa10049: Add the 74HC595 gpio expanders
Add the two daisy-chains of 74hc595s shift registers available on the
CFA-10049.

Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-09-11 09:51:30 +08:00
Maxime Ripard 223d1f9213 ARM: dts: cfa10049: Add SSP3 to the 10049 board
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-09-05 10:44:11 +08:00
Maxime Ripard 186e3d943a ARM: dts: mxs: Enable USB1 Host on the CFA-10049 expansion board
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-09-03 22:38:27 +08:00
Maxime Ripard db84c038d6 ARM: dts: mxs: Add the second I2C adapter to the CFA10049 expansion board
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
2012-09-03 19:02:41 +08:00