This patch adds support for lvds backlight on boards
i.MX6q-SabreSD and i.MX6dl-SabreSD
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
GPIO1_25 is used to reset the ethernet phy.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On imx6qdl-sabresd the SDHC2 and SDHC3 are 8 bit-wide, so pass the bus-width
property to reflect that.
Otherwise the mmc driver will operate with the default bus-width value of 4.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
USB OTG vbus pin needs to be configured as gpio function at
sabresd board.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
We enabled USB host 1, so host 1's vbus should be on to let
host 1 work.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
mx6 sabresd boards have a egalax touchscreen controller connected via I2C3.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This is useful for testing suspend/resume sequence.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The CLKO is widely used by imx6q board designs to clock audio codec.
Since most codecs accept 24 MHz frequency, let's initially set up CLKO
with OSC24M (cko <-- cko2 <-- osc). Then those board specific CLKO
setup for audio codec can be removed.
The board dts files also need an update on cko reference in codec node.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The imx6q and imx6dl are two pin-to-pin compatible SoCs. The same board
design can work with either chip plugged into the socket, e.g. sabresd
and sabreauto boards.
We currently define pin groups in imx6q.dtsi and imx6dl.dtsi
respectively because the pad macro names are different between two
chips. This brings a maintenance burden on having the same label point
to the same pin group defined in two places.
The patch replaces prefix MX6Q_ and MX6DL_ with MX6QDL_ for both SoCs
pad macro names. Then the pin groups becomes completely common between
imx6q and imx6dl and can just be moved into imx6qdl.dtsi, so that the
long term maintenance of imx6q/dt pin settings becomes easier.
Unfortunately, the change brings some dramatic diff stat, but it's all
about DTS file, and the ultimate net diff stat is good.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On Sabre SD, system controls WM8962 power by pulling up/down GPIO_4_10,
so add a regulator controled by GPIO_4_10 for WM8962.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The sabreauto and sabresd boards are common for imx6q and imx6dl.
Create imx6qdl-sabreauto.dtsi and imx6qdl-sabresd.dtsi for those
common parts.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>