Commit Graph

18 Commits

Author SHA1 Message Date
Peter Ujfalusi b306e7b819 ARM: dts: omap5-uevm: Remove pinmux for dmic pins
When the omap5-evm.dts file has been renamed to omap5-uevm.dts and the sEVM
support got deprecated in favor of uEVM (or Panda5) the content was not
validated.
Panda5 does not have support for digital microphones so remove the pinmux
section for it.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-10-23 11:40:47 +02:00
Peter Ujfalusi 472e623db8 ARM: dts: omap5-uevm: Correct twl6040 reset GPIO pinmux
When the omap5-evm.dts file has been renamed to omap5-uevm.dts and the sEVM
support got deprecated in favor of uEVM (or Panda5) the content was not
validated.
On uEVM the twl6040 reset GPIO is from gpio5_141 and not via gpio5_145, which
was the case in sEVM.

Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-10-23 11:40:46 +02:00
Nishanth Menon b8981d71b5 ARM: dts: omap5-uevm: add smps123 supply for CPU
regulator smps123 supply from Palmas PMIC powers CPU0 on OMAP5uEVM.

Based on a patch by J Keerthy <j-keerthy@ti.com>

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-10-22 17:33:06 +02:00
Eric Witcher 05bc85d1b5 ARM: dts: omap5-uevm: fix mcspi node pin descriptions
Correct mcspi pin descriptions to match corresponding node name and
add chip select number to be consistent with OMAP5 TRM.

Signed-off-by: Eric Witcher <ewitcher@mindspring.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-10-22 16:53:01 +02:00
Kishon Vijay Abraham I 46a25f1283 ARM: dts: omap5-uevm: remove always_on, boot_on from smps10_out1
smps10 should be enabled only in the case of host mode. So stop
doing always_on, boot_on from smps10_out1. The driver will enable
it in host mode.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-10-20 19:16:53 +02:00
Nishanth Menon 86583375aa ARM: dts: omap5-uevm: mark TWL6037 as system-power-controller
This allows the palmas pm_power_off to kick in on power off command
and switch off the board.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-10-11 21:06:44 +02:00
Roger Quadros 8ae9b5953c ARM: dts: omap5-uevm: Use reset-gpios for hsusb2/3_reset
We no longer need to model the RESET line as a regulator since
the USB phy-nop driver accepts "reset-gpios" property.

Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-10-11 21:06:35 +02:00
Felipe Balbi e3a412c9ee ARM: dts: OMAP5: add palmas-usb node
Without this node, there will be no palmas driver to notify
dwc3 that a cable has been connected and, without that, dwc3
will never initialize.

Signed-off-by: Felipe Balbi <balbi@ti.com>
[kishon@ti.com: added dt properties for enabling vbus/id interrupts
and fixed vbus-supply value after SMPS10 is modeled as 2 regulators]
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-10-08 17:51:42 +02:00
Kishon Vijay Abraham I 9448996c09 ARM: dts: omap5-uevm: Split SMPS10 in two nodes
SMPS10 has two outputs OUT1 and OUT2. Hence SMPS10 is modeled as
two regulators. The DT node is split to reflect it.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
2013-10-08 17:51:40 +02:00
Nishanth Menon bd3c5544a1 ARM: dts: omap5-uevm: update optional/unused regulator configurations
commit e00c27ef3b
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.

However, The regulator information is based on an older temporary
pre-production board variant and does not reflect production board
750-2628-XXX boards.

The following optional/unused regulators can be updated:

- SMPS9 supplies TWL6040 over VDDA_2v1_AUD. This regulator needs to be
enabled only when audio is active. Since it does not come active by
default, it does not require "always-on" or "boot-on".

- LDO2 and LDO8 do not go to any peripheral or connector on the board.
Further, these unused regulators should have been 2.8V for LDO2 and
3.0V for LDO8. Mark these LDOs as disabled in the dts until needed.

Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-07-29 23:43:20 -07:00
Nishanth Menon e18235a62a ARM: dts: omap5-uevm: fix regulator configurations mandatory for SoC
commit e00c27ef3b
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.

However, The regulator information is based on an older temporary
pre-production board variant and does not reflect production board
750-2628-XXX boards.

The following fixes are hence mandatory to ensure right voltage is
supplied to key OMAP5 SoC voltage rails:

- LDO1 supplies VDDAPHY_CAM which is OMAP5's vdda_csiporta/b/c. This
can only be supplied at 1.5V or 1.8V and we currently supply 2.8V.

To prevent any potential device damage risk, use the specified
1.5V-1.8V supply.

Remove 'always-on' and 'boot-on' settings here as it is
a 'on need' supply to SoC IP and is not enabled by PMIC by
default at boot.

- LDO3 supplies Low Latency Interface(LLI) hardware module which is a
special hardware to communicate with Modem. However since uEVM is
not setup by default for this communication, this should be disabled
by default.

Further, vdda_lli is supposed to be 1.5V and not 3V.

- LDO4 supplies VDDAPHY_DISP which is vdda_dsiporta/c/vdda_hdmi

This can only be supplied at 1.5V or 1.8V and we currently
supply 2.2V.

To prevent any potential device damage risk, use the specified
1.5V-1.8V supply.

Remove 'always-on' and 'boot-on' settings here as it is a 'on need'
supply to SoC IP and is not enabled by PMIC by default at boot.

- LDO6 supplies the board specified VDDS_1V2_WKUP supply going to
ldo_emu_wkup/vdds_hsic. To stay within the SoC specification supply
1.2V instead of 1.5V.

- LDO7 supplies VDD_VPP which is vpp1. This is currently configured for
1.5V which as per data manual "A pulse width of 1000 ns and an amplitude
of 2V is required to program each eFuse bit. Otherwise, VPP1 must not
be supplied".

So, fix the voltage to 2V. and disable the supply since we have no plans
of programming efuse bits - it can only be done once - in factory.

Further it is not enabled by default by PMIC so, 'boot-on' must be
removed, and the 'always-on' needs to be removed to achieve pulsing
if efuse needs to be programmed.

- LDO9 supplies the board specified vdds_sdcard supply going within SoC
specification of 1.8V or 3.0V. Further the supply is controlled by
switch enabled by REGEN3. So, introduce REGEN3 and map sdcard slot to
be powered by LDO9. Remove 'always-on' allowing the LDO to be disabled
on need basis.

Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-07-29 23:42:36 -07:00
Nishanth Menon 3709d32308 ARM: dts: omap5-uevm: document regulator signals used on the actual board
commit e00c27ef3b
(ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes)
introduced regulator entries for OMAP5uEVM.

However, currently we use the Palmas regulator names which is used for
different purposes on uEVM. Document the same based on 750-2628-XXX
boards - which is meant to be supported by this dts.

Reported-by: Marc Jüttner <m-juettner@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: J Keerthy <j-keerthy@ti.com>
Acked-by: Benoit Cousson <benoit.cousson@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
2013-07-29 23:41:26 -07:00
Roger Quadros 153030c22d ARM: dts: omap5-uevm: Provide USB Host PHY clock frequency
USB Host PHY clock on port 2 must be configured to 19.2MHz.
Provide this information.

Cc: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
2013-06-19 16:59:28 -05:00
J Keerthy e00c27ef3b ARM: dts: OMAP5: Add Palmas MFD node and regulator nodes
Add Palmas MFD node and the regulator nodes for OMAP5.

The node definitions are based on: https://lkml.org/lkml/2013/6/6/25

Boot tested on omap5-uevm board.

Signed-off-by: Graeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
2013-06-18 19:31:50 -05:00
Sourav Poddar ed22fee3de ARM: dts: omap5-uevm: Add uart pinctrl data
Booting omap5 uevm results in the following error
"did not get pins for uart error: -19"

This happens because omap5 uevm dts file is not adapted
to use uart through pinctrl framework.
Populate uart pinctrl data to get rid of the error.

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
[r.sricharan@ti.com: Replaced constants with preprocessor macros]
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
2013-06-18 18:53:44 -05:00
Dan Murphy 66155302c4 ARM: dts: omap5-uevm: Add LED support for uEVM blue LED
Add support for blue LED 1 off of GPIO 153.
Make the LED a heartbeat LED
Configure the MUX for GPIO output.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
[r.sricharan@ti.com: Replaced constants with preprocessor macros]
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
2013-06-18 18:53:44 -05:00
Roger Quadros ed7f8e8a1c ARM: dts: omap5-uevm: Add USB Host support
Provide the RESET regulators for the USB PHYs, the USB Host
port modes and the PHY devices.

Also provide pin multiplexer information for the USB host
pins.

Signed-off-by: Roger Quadros <rogerq@ti.com>
[r.sricharan@ti.com: Replaced constants with preprocessor macros]
Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
2013-06-18 18:53:44 -05:00
Sricharan R fa63d03728 ARM: dts: omap5: Make uevm as the official board and deprecate sevm support
The uevm is the only official board supported for the OMAP5 soc
in mainline. The existent sevm platform will no more be supported.
Hence cleaning up the board dts file to have only the data
required for uevm.

Renaming the board dts file and adding the following cleanups.

 * There are no devices connected on I2C 2,3,4 buses. So remove
   the pinmux data for the same.

 * OMAP5432 and DDR3 memory is used in the uevm. Temperature polling
   is not supported with DDR3 memories. Because of DDR3 phy limitation
   the voltage change across DVFS and all shadow registers for DVFS on
   DDR3 is not supported. Hence the emif kernel driver is not required,
   so removing the DDR3 device file and emif nodes for uevm.

 * Keypad is not supported on uevm. So remove the device node.

Signed-off-by: Sricharan R <r.sricharan@ti.com>
Signed-off-by: Benoit Cousson <benoit.cousson@linaro.org>
2013-06-18 18:53:43 -05:00