Commit Graph

9 Commits

Author SHA1 Message Date
Linus Walleij 5026119fbe ARM: ux500: move the WLAN GPIO pin setup to the device tree
This moves some of the pin setup related to the CW1200 WLAN
module over to the device tree. As the driver is not yet
activated for the CW1200 WLAN we do not assign this pinctrl
state to any device node yet.

Get rid of the cmdline argument passing of a certain U9500
platform variant, as this is not supported by the kernel or
any device tree.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:56 +01:00
Linus Walleij 279571358d ARM: ux500: move SKE pin config to device tree
This moves the SKE keypad pin control table out of the board
file and into the device tree. This was previously set to be
active on all MOP500 and HREF boards but after reading the
schematic this seems incorrect: the HREFv60 and later uses
one of these for MC5 and no reference designs have the SKE
connected to any hardware so just leave the pins alone
in the power-on state.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:56 +01:00
Linus Walleij 817a5b967d ARM: ux500: move MCDE pin config to device tree
This moves the MCDE pin control table out of the board file
and into the device tree. Some pins and configs have been
marked as used by sub-devices or slaves to the MCDE, such
as I2C device 0-070 which is the HDMI interface circuit
AV8100, but the pins rather belong to the MCDE SOC block
as they come out of the main ASIC. The touch screen GPIO
is not related to MCDE so this gets deleted and need to
be tied to the respective touch screen (I2C) device
once that device is added instead.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:56 +01:00
Linus Walleij 38656820aa ARM: ux500: move SPI pin config to device tree
This moves the SPI pin control table out of the board file
and into the device tree. Move the specific setting for
SSP0 on the HREFprev60 into the prev60-specific DTS file.
The SPI2 configuration is not really connected to any device,
as it will conflict with GPIO218 which is used on all HREFs.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij a12f703c5a ARM: ux500: move MUSB pin config to device tree
This moves the MUSB pin control table out of the board file
and into the device tree. Tie the config to the on-chip MUSB
device rather than the ab8500-usb device which is off-chip.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij 70b41abc15 ARM: ux500: move MSP pin control to the device tree
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add nodes for MSP0 and MSP2 on the HREF and Snowball
so we can reference the pins properly.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij 1e66235330 ARM: ux500: move MMC/SD/SDIO pin control to the device tree
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add entries for SDI1 and SDI2 on the Snowball so that the
WLAN pins on SDI1 can be used further on, and the unused pins
on SDI2 can be put to sleep.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij 96fee13f0f ARM: ux500: move I2C pin control to the device tree
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Define possible states also for I2C4 even if it's not
used by any board file at this time.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij 3bfdebbaeb ARM: ux500: move UART pin control to the device tree
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree.

We create a new .dtsi-file to be shared between all the
MOP500-related boards, that include all HREF variants and
the Snowball board. Assign pin states for HREF and Snowball
boards alike.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00