Commit Graph

9 Commits

Author SHA1 Message Date
Ulf Hansson a1ab5e4c80 ARM: ux500: Configure regulator for I/O voltage for SD-card slot
To be able to enable SDR12|25 for SD-cards, we needed to fixup the
configuration in DT of the gpio regulator, which handles the signal
voltage level. Some configuration were missing and some were wrong.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-12-13 10:27:58 +01:00
Ulf Hansson a987a3accc ARM: ux500: Refactor common DT configs for sdi[n] devices
Remove duplicated configurations and move specific details into
each corresponding dtsi file for the href versions.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: devicetree@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-12-13 10:25:37 +01:00
Linus Walleij 3ae2750a8c ARM: ux500: move old HREF ipgpio to the device tree
The old HREFs (MOP500) were controlling an image-processor
GPIO (IPGPIO) by using hogs. Do the same thing with device tree
and get rid of the mop500_pins setting.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:56 +01:00
Linus Walleij 38656820aa ARM: ux500: move SPI pin config to device tree
This moves the SPI pin control table out of the board file
and into the device tree. Move the specific setting for
SSP0 on the HREFprev60 into the prev60-specific DTS file.
The SPI2 configuration is not really connected to any device,
as it will conflict with GPIO218 which is used on all HREFs.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij a45cb698a7 ARM: ux500: move GPIO217/218 config to device tree
This moves the input-pulled-up setting for GPIO217 as used
on the HREFs prior to v60 from the boardfile to the device
tree. GPIO218 is only used with the TVK UIB so move it to
that .dtsi file.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij 1e66235330 ARM: ux500: move MMC/SD/SDIO pin control to the device tree
This moves the static, device-tied pin control configuration
out of the board file board-mop500-pins.c and into the device
tree. Add entries for SDI1 and SDI2 on the Snowball so that the
WLAN pins on SDI1 can be used further on, and the unused pins
on SDI2 can be put to sleep.

Cc: Lee Jones <lee.jones@linaro.org>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:55 +01:00
Linus Walleij 7e0a51a031 ARM: ux500: adjust the TC3589x devices to the binding
The TC3589x devices appearing in the ST Ericsson device trees
are adjusted to use the new binding so this is in a good shape,
and we add the keypad on the TVK1281618 UIB so this is working
again.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-11-26 21:01:54 +01:00
Linus Walleij 741a6c4c59 ARM: ux500: move BU21013 touchpad GPIOs into top-level DTS
The BU21013 touchscreen GPIOs have been pretty confused, correct
them per board, and move the GPIO assignments up to the top
level DTS file so we can control it from there, and avoid defining
the GPIO assignments for non-ST UIB equipped boards.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-10-03 10:29:24 +02:00
Linus Walleij 01dc909fa1 ARM: ux500: split the HREF DTS files from two to four
As the device tree conversion did away with the ability to
auto-detect the UIB (User Interface Board) version from attempting
to read an I2C address, we now have to pass the knowledge of
what UIB is mounted through the device tree. This gives rise
to four possible board permutations:

- HREF prior to v60, ST UIB (hrefprev60-stuib)
- HREF prior to v60, TVK1281618 UIB (hrefprev60-tvk)
- HREF v60 and later, ST UIB (href60plus-stuib)
- HREF v60 and later, TVK1281618 UIB (hrefv60plus-tvk)

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2013-10-02 16:17:04 +02:00