Nobody has actually used the type (VERIFY_READ vs VERIFY_WRITE) argument
of the user address range verification function since we got rid of the
old racy i386-only code to walk page tables by hand.
It existed because the original 80386 would not honor the write protect
bit when in kernel mode, so you had to do COW by hand before doing any
user access. But we haven't supported that in a long time, and these
days the 'type' argument is a purely historical artifact.
A discussion about extending 'user_access_begin()' to do the range
checking resulted this patch, because there is no way we're going to
move the old VERIFY_xyz interface to that model. And it's best done at
the end of the merge window when I've done most of my merges, so let's
just get this done once and for all.
This patch was mostly done with a sed-script, with manual fix-ups for
the cases that weren't of the trivial 'access_ok(VERIFY_xyz' form.
There were a couple of notable cases:
- csky still had the old "verify_area()" name as an alias.
- the iter_iov code had magical hardcoded knowledge of the actual
values of VERIFY_{READ,WRITE} (not that they mattered, since nothing
really used it)
- microblaze used the type argument for a debug printout
but other than those oddities this should be a total no-op patch.
I tried to fix up all architectures, did fairly extensive grepping for
access_ok() uses, and the changes are trivial, but I may have missed
something. Any missed conversion should be trivially fixable, though.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Changes do_insn*_ioctl functions to allow for data lengths for each
comedi_insn of up to 2^16. This patch also changes these functions to only
allocate as much memory as is necessary for each comedi_insn, rather than
allocating a fixed-sized scratch space.
In testing some user-space code for the new INSN_DEVICE_CONFIG_GET_ROUTES
facility with some newer hardware, I discovered that do_insn_ioctl and
do_insnlist_ioctl limited the amount of data that can be passed into the
kernel for insn's to a length of 256. For some newer hardware, the number
of routes can be greater than 1000. Working around the old limits (256)
would complicate the user-space/kernel interaction.
The new upper limit is reasonable with current memory available and does
not otherwise impact the memory footprint for any current or otherwise
typical configuration.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes multiple occurences of the checkpatch.pl warning:
WARNING: Missing or malformed SPDX-License-Identifier tag in line 1
NB. This is an additional patch and does not overlap the patch sent
yesterday for 8255.h. Should have sent them all together.
Newb mistake.
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Stephen Davies <davo2002@tpg.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a spelling mistake in message text in the call to unittest,
fix this.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the checkpatch.pl warning:
WARNING: Missing or malformed SPDX-License-Identifier tag in line 1
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Stephen Davies <davo2002@tpg.com.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Uses a single macro to define multiple macros that represent a series of
terminals for NI devices. This patch also redefines NI_MAX_COUNTERS as the
maximum number of counters possible on NI devices (instead of the maximum
index of the counters). This was a little confusing and caused a bug in
commit 347e244884 ("staging: comedi: tio: implement global tio/ctr routing")
when setting/reading registers for counter terminals.
Fixes: 347e244884 ("staging: comedi: tio: implement global tio/ctr routing")
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes implementation of INSN_CONFIG_GET_CMD_TIMING_CONSTRAINTS for
ni_mio devices. The previous patch should have used the channel
information passed in to scale the result by the number of channels being
used.
Fixes: 51fd367383 ("staging: comedi: ni_mio_common: implement INSN_CONFIG_GET_CMD_TIMING_CONSTRAINTS")
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `insn_write` handler for the AO subdevice (`labpc_ao_insn_write()`)
currently ignores `insn->n` (the number of samples to write) and assumes
a single sample is to be written. But `insn->n` could be 0, meaning no
samples should be written, in which case `data[0]` is invalid.
Follow the usual Comedi guidelines and change `labpc_ao_insn_write()` to
write the specified number of samples. This fixes the assumption that
`data[0]` is valid.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `insn_write` handler for the AO subdevice
(`cb_pcidda_ao_insn_write()`) currently ignores `insn->n` (the number of
samples to write) and assumes a single sample is to be written. But
`insn->n` could be 0, meaning no samples should be written, in which
case `data[0]` is invalid.
Follow the usual Comedi guidelines and change
`cb_pcidda_ao_insn_write()` to write the specified number of samples.
This fixes the assumption that `data[0]` is valid.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `insn_read` handler for the EEPROM subdevice
(`apci3501_eeprom_insn_read()`) currently ignores `insn->n` (the number
of samples to be read) and assumes a single sample is to be read. But
`insn->n` could be 0, meaning no samples should be read, in which case
`data[0]` ought not to be written. (The comedi core at least ensures
that `data[0]` exists, but we should not rely on that.)
Following the usual Comedi guidelines and interpret `insn->n` as the
number of samples to be read, but only read the EEPROM location once and
make `insn->n` copies, as we don't expect the contents of the EEPROM
location to change between readings.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The contents of the Comedi configuration instruction
`INSN_CONFIG_TIMER_1` instruction are not very well defined, but the one
driver that uses it (the "cb_pcidas64" driver for the PCI-DAS4020/12
card) assumes its `insn->n` is 5. Add a check in
`check_insn_config_length()` to verify that `insn->n` is correct for
this configuration instruction.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `insn_read` handler for the EEPROM subdevice (`eeprom_insn_read()`)
currently ignores `insn->n` (the number of samples to be read) and
assumes a single sample is to be read. But `insn->n` could be 0,
meaning no samples should be read, in which case `data[0]` ought not to
be written. (The comedi core at least ensures that `data[0]` exists,
but we should not rely on that.)
Follow the usual Comedi guidelines and interpret `insn->n` as the number
of samples to be read, but only read the EEPROM location once and make
`insn->n` copies, as we don't expect the contents of the EEPROM location
to change between readings.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The `insn_write` handler for the AO subdevice (`ao_winsn()` currently
ignores `insn->n` (the number of samples to write) and assumes a single
sample is to be written. But `insn->n` could be 0, meaning no samples
should be written, in which case `data[0]` is invalid.
Follow the usual Comedi guidelines and change `ao_winsn()` to write the
specified number of samples. This fixes the assumption that `data[0]`
is valid.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, there are multiple missing break statements in two switch code
blocks. This makes the execution path to fall all the way down through
to the default cases, which makes the function ni_tio_set_gate_src() to
always return -EINVAL.
Fix this by adding the missing break statements.
Also, notice that due to the absence of the break statements,
the following pieces of code are unreachable:
1078 if (ret)
1079 return ret;
1080 /* 3. reenable & set mode to starts things back up */
1081 ni_tio_set_gate_mode(counter, src);
1098 if (ret)
1099 return ret;
1100 /* 3. reenable & set mode to starts things back up */
1101 ni_tio_set_gate2_mode(counter, src);
So, by adding the missing breaks, this patch also fixes the problem
above.
Addresses-Coverity-ID: 1474165 ("Missing break in switch")
Addresses-Coverity-ID: 1474162 ("Structurally dead code")
Fixes: 347e244884 ("staging: comedi: tio: implement global tio/ctr routing")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Provides the device-global routing interface for ni_660x devices. Using
the device-global names in comedi_cmd structures for commands was already
supported through the ni_tio module.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cleans up the pfi routing code to make it easier to follow, read, and also
to prepare to use this cleaned up code for enabling the device-global
routing interface for ni_660x devices.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, only the PXI version of the NI-6608 board was supported. This
change adds support for the PCI version as well.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds tio sub-devices of ni_mio_common supported hardware to the
implementation of test_route, connect_route, disconnect_route. This change
delegates the actual functionality to the ni_tio module.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds ability to use device-global names in command args, in particular
cmd->start_arg (for NI_CtrArmStartTrigger), and cmd->scan_begin_arg or
cmd->convert_arg (either is used to specify NI_CtrGate, with preference
given to cmd->scan_begin_arg, if it is set).
The actual arguments of cmd->start_arg are not fully checked against known
register values for the particular devices because these are not documented
or currently known. This follows the precedence of prior versions of the
tio driver. Should these become known, they should be annotated in the
route_values tables and the set of lines in ni_tio_cmdtest should be
uncommented to allow the tests to be made.
This patch also adds interface functions that allow routes for particular
counter route destinations to be made/queried/unmade. This allows overseer
modules to implement test_route, connect_route, and disconnect_route. As a
part of these changes, various functions were cleaned up and clarified.
These new interface functions allow direct writing/reading of register
values. This is an example of exactly what the new device-global access
was intended to solve: the old interface was not consistent with other
portions of the ni_* drivers--it did not allow full register values to be
given for various MUXes. Instead, the old interface _did_ abstract away
some of the actual hardware from the underlying devices, but it was not
consistent with any other NI hardware. Allowing the device-global
identifiers to be used, the new patch provides for consistency across all
ni_* drivers. One final note: these changes provide for backwards
compatibility by allowing the older values to still be used in through the
pre-existing kernel interfaces--though not in the new device-global
test/dis/connect/route interfaces.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement the ability to route various signals to NI_CtrOut(x) pin. This
pin is also known as GPFO_{0,1} in the DAQ STC.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Implement device-global config interface for ni_mio devices. In
particular, this patch implements:
INSN_DEVICE_CONFIG_TEST_ROUTE,
INSN_DEVICE_CONFIG_CONNECT_ROUTE,
INSN_DEVICE_CONFIG_DISCONNECT_ROUTE,
INSN_DEVICE_CONFIG_GET_ROUTES
for the ni mio devices. This means that the new abstracted signal/terminal
names can be used to define signal routing with regards to the PFI
terminals and RTSI trigger bus lines.
This also adds ability to identify PFI and RTSI channels on the PFI and
RTSI subdevices using the new device-global names. This does not change
the values that are set for channel output selections using the subdevice
interfaces--these still require direct register values.
Annotates and updates tables of register values to reflect this new
implementation status.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use new signal routing capability for all comedi command *_src == TRIG_EXT
options. This new interface allows the user specify signals and terminals
as TRIG_EXT sources using a very consistent naming convention. Furthermore,
the interface allows backwards compatibility to prior behavior of
specifying register-level (or near register-level) values as *_arg options
when *_src == TRIG_EXT.
Annotates and updates tables of register values to reflect this new
implementation status.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds interface and associated unittests for accessing/looking-up/validating
the new ni routing table information.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
See README for a thorough discussion of this content.
Adds tables of all register values for routing various signals to various
terminals on National Instruments hardware. This information is directly
compared to and taken from register-level programming documentation and/or
register-level programming examples as provided by National Instruments.
Furthermore, this information was mostly compared (favorably) to the
register values already used in the comedi drivers for NI hardware.
Adds tables of valid routes for many devices. This information is not
consistent from device to device, nor entirely consistent within device
families. One additional major challenge is that this information does not
seem to be obtainable in any programmatic fashion, neither through the
proprietary NIDAQmx(-base) c-libraries, nor with register level
programming, _nor_ through any documentation. In fact, the only consistent
source of this information is through the proprietary NI-MAX software,
which currently only runs on Windows platforms. A further challenge is
that this information cannot be exported from NI-MAX, except by screenshot.
The collection and maintenance of this information is somewhat tedious and
requires frequent re-examination and comparison of NI-MAX and/or the
NI-MHDDK documentation (register programming information) and NI-MHDDK
examples. Tools are added with this patch to facilitate generating CSV
files from the data tables. These CSV files can be used with a spreadsheet
program to provide better visual comparision with screenshots gathered from
NI-MAX. Tools are also added to regenerate the data tables from CSV
content--this greatly enhances updating data tables with large changes
(such as when adding devices).
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds interface for configuring options that are global to all sub-devices.
For now, only options to configure device-globally identified signal routes
have been defined.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change adds abstracted constants for National Instruments
terminal/signal names.
Some background:
There have been significant confusions over the past many years for users
when trying to understand how to connect to/from signals and terminals on
NI hardware using comedi. The major reason for this is that the actual
register values were exposed and required to be used by users. Several
major reasons exist why this caused major confusion for users:
1) The register values are _NOT_ in user documentation, but rather in
arcane locations, such as a few register programming manuals that are
increasingly hard to find and the NI-MHDDK (comments in in example
code). There is no one place to find the various valid values of the
registers.
2) The register values are _NOT_ completely consistent. There is no way
to gain any sense of intuition of which values, or even enums one
should use for various registers. There was some attempt in prior use
of comedi to name enums such that a user might know which enums should
be used for varying purposes, but the end-user had to gain a knowledge
of register values to correctly wield this approach.
3) The names for signals and registers found in the various register
level programming manuals and vendor-provided documentation are _not_
even close to the same names that are in the end-user documentation.
Similar confusion, albeit less, plagued NI's previous version of their own
proprietary drivers. Earlier than 2003, NI greatly simplified the
situation for users by releasing a new API that abstracted the names of
signals/terminals to a common and intuitive set of names. In addition,
this new API provided a much more common interface to use for most of NI
hardware.
The names added here mirror the names chosen and well documented by NI.
These names are exposed to the user via the comedilib user library. By
keeping the names in this format, in spite of the use of CamelScript,
maintenance will be greatly eased and confusion for users _and_ comedi
developers will be greatly reduced.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds a framework for unittests for comedi drivers. It was certainly
possible to write some unit tests before and test various aspects of a
particular driver, but this framework makes this a bit easier and hopefully
inspires more unittest modules to be written.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds implementation of the new INSN_CONFIG_GET_CMD_TIMING_CONSTRAINTS
instruction.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds implementation of the new INSN_CONFIG_GET_CMD_TIMING_CONSTRAINTS
instruction. This patch also adds data for this implementation, based on
spec sheets from NI.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds implementation of the new INSN_CONFIG_GET_CMD_TIMING_CONSTRAINTS
instruction. This patch also adds data for digital subdevices that are
streaming capable (within the ni_mio_* family). Mostly, only the m-series
devices are capable of digital streaming.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds facility to directly query the hardware speed limits of subdevices,
in particular for scan_begin and convert signals. This information can be
critical for integrating comedi with other hardware modules, and also
comedi modules together with software where software requires specific
timing capabilities in order to properly coordinate multiple devices.
Currently, comedi_command_test almost satisfies this need, but really only
for when *_src == TRIG_TIMER. For *_src == TRIG_EXT, comedi_command_test
does not help at all. For many subdevices, one might simply use
*_src==TRIG_TIMER in command_test in order to determine these limits. For
other subdevices, this tactic does not work since *_src == TRIG_TIMER might
not be valid. There is also the possibility that the timing limits are
different between the TRIG_TIMER and TRIG_EXT modes.
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes two problems introduced as early as
commit 03aef4b6dc ("Staging: comedi: add ni_mio_common code"):
(1) Ensures that the last four bits of NISTC_RTSI_TRIGB_OUT_REG register is
not unduly overwritten on e-series devices. On e-series devices, the
first three of the last four bits are reserved. The last bit defines
the output selection of the RGOUT0 pin, otherwise known as
RTSI_Sub_Selection. For m-series devices, these last four bits are
indeed used as the output selection of the RTSI7 pin (and the
RTSI_Sub_Selection bit for the RGOUT0 pin is moved to the
RTSI_Trig_Direction register.
(2) Allows all 4 RTSI_BRD lines to be treated as valid sources for RTSI
lines.
This patch also cleans up the ni_get_rtsi_routing command for readability.
Fixes: 03aef4b6dc ("Staging: comedi: add ni_mio_common code")
Signed-off-by: Spencer E. Olson <olsonse@umich.edu>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PFI subdevice flags indicate that the subdevice is readable and
writeable, but that is only true for the supported "M-series" boards,
not the older "E-series" boards. Only set the SDF_READABLE and
SDF_WRITABLE subdevice flags for the M-series boards. These two flags
are mainly for informational purposes.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's not been any work on this driver since it was originally merged,
and it really needs to be rewritten to use the serdev layer instead if
people really need/want it.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Shift '=' assignment operator to the end of previous
line to conform to preferred kernel style line wrapping.
Issue reported by checkpatch CHECK.
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable segpos is being assigned but is never used hence it is redundant
and can be removed.
Cleans up clang warning:
warning: variable 'segpos' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a '>' vs '<' typo so this loop is a no-op.
Fixes: d35dcc89fc ("staging: comedi: quatech_daqp_cs: fix daqp_ao_insn_write()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed SPDX-License-Identifier comment on first line
Signed-off-by: ankit patel <ankit.mayurbhai.patel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed SPDX-License-Identifier comment on first line
Signed-off-by: ankit patel <ankit.mayurbhai.patel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed SPDX-License-Identifier comment on first line
Signed-off-by: ankit patel <ankit.mayurbhai.patel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed SPDX-License-Identifier comment on first line
Signed-off-by: ankit patel <ankit.mayurbhai.patel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixed SPDX-License-Identifier comment on first line
Signed-off-by: ankit patel <ankit.mayurbhai.patel@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Improve readability of comedi_nsamples_left:
a) Reduce nesting by using more return statements.
b) Declare variables scans_left and samples_left at start of function.
c) Change type of scans_Left to unsigned long long to avoid cast.
Signed-off-by: Chris Opperman <eklikeroomys@gmail.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checkpatch.pl complains about packbits function pointer that lacks
parameters name.
Add parameter names to packbits function pointer.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checkpatch.pl complains about "quoted string split across lines" for
string in MODULE_DESCRIPTION().
Put string on only one line.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Checkpatch complains on bool bitfields to be an int or u8/u16/u32
bitfield.
Make bool bit-fields to be unsigned int bit-fields.
Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
Reviewed-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds