In AP mode, If AP advertises HE capabilities, set to true
bss_conf::he_supported so that the Driver knows about it.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These checks aren't necessary, cfg80211 never passes NULL.
Some static checkers complain about the missing checks on
the next line, but really the NULL checks are unnecessary.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make ieee80211_send_layer2_update() a common function so other drivers
can re-use it.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As explained in ieee80211_delayed_tailroom_dec(), during roam,
keys of the old AP will be destroyed and new keys will be
installed. Deletion of the old key causes
crypto_tx_tailroom_needed_cnt to go from 1 to 0 and the new key
installation causes a transition from 0 to 1.
Whenever crypto_tx_tailroom_needed_cnt transitions from 0 to 1,
we invoke synchronize_net(); the reason for doing this is to avoid
a race in the TX path as explained in increment_tailroom_need_count().
This synchronize_net() operation can be slow and can affect the station
roam time. To avoid this, decrementing the crypto_tx_tailroom_needed_cnt
is delayed for a while so that upon installation of new key the
transition would be from 1 to 2 instead of 0 to 1 and thereby
improving the roam time.
This is all correct for a STA iftype, but deferring the tailroom_needed
decrement for other iftypes may be unnecessary.
For example, let's consider the case of a 4-addr client connecting to
an AP for which AP_VLAN interface is also created, let the initial
value for tailroom_needed on the AP be 1.
* 4-addr client connects to the AP (AP: tailroom_needed = 1)
* AP will clear old keys, delay decrement of tailroom_needed count
* AP_VLAN is created, it takes the tailroom count from master
(AP_VLAN: tailroom_needed = 1, AP: tailroom_needed = 1)
* Install new key for the station, assume key is plumbed in the HW,
there won't be any change in tailroom_needed count on AP iface
* Delayed decrement of tailroom_needed count on AP
(AP: tailroom_needed = 0, AP_VLAN: tailroom_needed = 1)
Because of the delayed decrement on AP iface, tailroom_needed count goes
out of sync between AP(master iface) and AP_VLAN(slave iface) and
there would be unnecessary tailroom created for the packets going
through AP_VLAN iface.
Also, WARN_ONs were observed while trying to bring down the AP_VLAN
interface:
(warn_slowpath_common) (warn_slowpath_null+0x18/0x20)
(warn_slowpath_null) (ieee80211_free_keys+0x114/0x1e4)
(ieee80211_free_keys) (ieee80211_del_virtual_monitor+0x51c/0x850)
(ieee80211_del_virtual_monitor) (ieee80211_stop+0x30/0x3c)
(ieee80211_stop) (__dev_close_many+0x94/0xb8)
(__dev_close_many) (dev_close_many+0x5c/0xc8)
Restricting delayed decrement to station interface alone fixes the problem
and it makes sense to do so because delayed decrement is done to improve
roam time which is applicable only for client devices.
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support for HE in mac80211 conforming with P802.11ax_D1.4.
Johannes: Fix another bug with the buf_size comparison in agg-rx.c.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support the new random SN and minimal probe request contents
scan flags for the case of software scan - for hardware scan
the drivers need to opt in, but may need to do only that,
depending on their implementation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
This fixes memory leaks in the case where we just have the
station info on the stack for internal usage without sending
it to cfg80211.
Fixes: 8689c051a2 ("cfg80211: dynamically allocate per-tid stats for station info")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This adds support to mac80211 to export TXQ stats via the newly added
cfg80211 API.
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If userspace requested control port frames to go over 80211, then do so.
The control packets are intercepted just prior to delivery of the packet
to the underlying network device.
Pre-authentication type frames (protocol: 0x88c7) are also forwarded
over nl80211.
Signed-off-by: Denis Kenzior <denkenz@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
ETSI has recently added new requirements that restrict the WMM
parameter values for 5GHz frequencies. We need to take care of the
following scenarios in order to comply with these new requirements:
1. When using mac80211 default values;
2. When the userspace tries to configure its own values;
3. When associating to an AP which advertises WWM IE.
When associating to an AP, the client uses the values in the
advertised WMM IE. But the AP may not comply with the new ETSI
requirements, so the client needs to check the current regulatory
rules and use those limits accordingly.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
With drivers implementing rate control in driver or firmware
rate_control_send_low() may not get called, and thus the
driver needs to know about changes in the multicast rate.
Add and use a new BSS change flag for this.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When powersave is disabled for the interface, we can do fast-rx anyway.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
[fixed indentation on one line]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
cfg80211: fix cfg80211_beacon_dup
-> old bug in this code
cfg80211: clear wep keys after disconnection
-> certain ways of disconnecting left the keys
mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
-> alignment issues with using 14 bytes
mac80211: Do not disconnect on invalid operating class
-> if the AP has a bogus operating class, let it be
mac80211: Fix sending ADDBA response for an ongoing session
-> don't send the same frame twice
cfg80211: use only 1Mbps for basic rates in mesh
-> interop issue with old versions of our code
mac80211_hwsim: don't use WQ_MEM_RECLAIM
-> it causes splats because it flushes work on a non-reclaim WQ
regulatory: add NUL to request alpha2
-> nla_put_string() issue from Kees
mac80211: mesh: fix wrong mesh TTL offset calculation
-> protocol issue
mac80211: fix a possible leak of station stats
-> error path might leak memory
mac80211: fix calling sleeping function in atomic context
-> percpu allocations need to be made with gfp flags
-----BEGIN PGP SIGNATURE-----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=kwiY
-----END PGP SIGNATURE-----
Merge tag 'mac80211-for-davem-2018-02-22' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Various fixes across the tree, the shortlog basically says it all:
cfg80211: fix cfg80211_beacon_dup
-> old bug in this code
cfg80211: clear wep keys after disconnection
-> certain ways of disconnecting left the keys
mac80211: round IEEE80211_TX_STATUS_HEADROOM up to multiple of 4
-> alignment issues with using 14 bytes
mac80211: Do not disconnect on invalid operating class
-> if the AP has a bogus operating class, let it be
mac80211: Fix sending ADDBA response for an ongoing session
-> don't send the same frame twice
cfg80211: use only 1Mbps for basic rates in mesh
-> interop issue with old versions of our code
mac80211_hwsim: don't use WQ_MEM_RECLAIM
-> it causes splats because it flushes work on a non-reclaim WQ
regulatory: add NUL to request alpha2
-> nla_put_string() issue from Kees
mac80211: mesh: fix wrong mesh TTL offset calculation
-> protocol issue
mac80211: fix a possible leak of station stats
-> error path might leak memory
mac80211: fix calling sleeping function in atomic context
-> percpu allocations need to be made with gfp flags
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc-8 warns about some obviously incorrect code:
net/mac80211/cfg.c: In function 'cfg80211_beacon_dup':
net/mac80211/cfg.c:2896:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]
From the context, I conclude that we want to copy from beacon into
new_beacon, as we do in the rest of the function.
Cc: stable@vger.kernel.org
Fixes: 73da7d5bab ("mac80211: add channel switch command and beacon callbacks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in some cases I replaced "fall through on else" and
"otherwise fall through" comments with just a "fall through" comment,
which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ben reported that when the user rate mask is rejected for not
matching any basic rate, the driver had already been configured.
This is clearly an oversight in my original change, fix this by
doing the validation before calling the driver.
Reported-by: Ben Greear <greearb@candelatech.com>
Fixes: e8e4f5280d ("mac80211: reject/clear user rate mask if not usable")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 allows to modify the SMPS state of an AP both,
when it is started, and after it has been started. Such a
change will trigger an action frame to all the peers that
are currently connected, and will be remembered so that
new peers will get notified as soon as they connect (since
the SMPS setting in the beacon may not be the right one).
This means that we need to remember the SMPS state
currently requested as well as the SMPS state that was
configured initially (and advertised in the beacon).
The former is bss->req_smps and the latter is
sdata->smps_mode.
Initially, the AP interface could only be started with
SMPS_OFF, which means that sdata->smps_mode was SMPS_OFF
always. Later, a nl80211 API was added to be able to start
an AP with a different AP mode. That code forgot to update
bss->req_smps and because of that, if the AP interface was
started with SMPS_DYNAMIC, we had:
sdata->smps_mode = SMPS_DYNAMIC
bss->req_smps = SMPS_OFF
That configuration made mac80211 think it needs to fire off
an action frame to any new station connecting to the AP in
order to let it know that the actual SMPS configuration is
SMPS_OFF.
Fix that by properly setting bss->req_smps in
ieee80211_start_ap.
Fixes: f699317487 ("mac80211: set smps_mode according to ap params")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If userspace has flagged support for DFS earlier, then we can follow CSA
to DFS channels. So instead of rejecting the switch, allow it to happen
if the flag has been set during mesh setup.
Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even
if the channel context configuration is NULL. This crashes for chipsets
which support 5 Ghz alone when it tries to access members of 'sband'.
Channel context configuration can be NULL in multivif case and when
channel switch is in progress (or) when it fails. Fix this by replacing
the API 'ieee80211_get_sdata_band' with 'ieee80211_get_sband' which
returns a NULL pointer for sband when the channel configuration is NULL.
An example scenario is as below:
In multivif mode (AP + STA) with drivers like ath10k, when we do a
channel switch in the AP vif (which has a number of clients connected)
and a STA vif which is connected to some other AP, when the channel
switch in AP vif fails, while the STA vifs tries to connect to the
other AP, there is a window where the channel context is NULL/invalid
and this results in a crash while the clients connected to the AP vif
tries to reconnect and this race is very similar to the one investigated
by Michal in https://patchwork.kernel.org/patch/3788161/ and this does
happens with hardware that supports 5Ghz alone after long hours of
testing with continuous channel switch on the AP vif
ieee80211 phy0: channel context reservation cannot be finalized because
some interfaces aren't switching
wlan0: failed to finalize CSA, disconnecting
wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice
(Reason: 3=DEAUTH_LEAVING)
WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211]
[<bf77272c>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211]))
[<bf73cc50>] (nl80211_new_station [cfg80211])
Unable to handle kernel NULL pointer dereference at virtual
address 00000014
pgd = d5f4c000
Internal error: Oops: 17 [#1] PREEMPT SMP ARM
PC is at sta_info_alloc+0x380/0x3fc [mac80211]
LR is at sta_info_alloc+0x37c/0x3fc [mac80211]
[<bf772738>] (sta_info_alloc [mac80211])
[<bf78776c>] (ieee80211_add_station [mac80211])
[<bf73cc50>] (nl80211_new_station [cfg80211]))
Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
At least on iwlwifi, sometimes lockdep complains that we can
lock
chanctx_mtx -> mvm.mutex -> iflist_mtx
(due to iterate_interfaces)
and
iflist_mtx -> chanctx_mtx
Remove the latter dependency in mac80211 by using the RTNL
that we already hold in one case, and can relatively easily
achieve in the other case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For multiple scheduled scan support the driver needs to know which
scheduled scan request is being stopped. Pass the request id in the
.sched_scan_stop() callback.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Refactor the code to have common code for changing monitor
options when adding and changing virtual interfaces. This
will make it easier to add BPF filters to both paths. Note
that this code carefully checks the error conditions first
and only then applies the changes, to guarantee atomicity.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead passing both flags, which can be NULL, and vif_params,
which are never NULL, move the flags into the vif_params and
use BIT(0), which is invalid from userspace, to indicate that
the flags were changed.
While updating all drivers, fix a small bug in wil6210 where
it was setting the flags to 0 instead of leaving them unchanged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The MU-MIMO monitor follow functionality is broken because it
doesn't clear the MU-MIMO owner even if both follow features
are disabled. Fix that, and while at it move the code into a
new helper function. Call this also when creating a new monitor
interface to prepare for an upcoming cfg80211 change allowing
that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When changing monitor parameters, not setting the MU-MIMO attributes
should mean that they're not changed - it's documented that to turn
the feature off it's necessary to set all-zero group membership and
an invalid follow-address. This isn't implemented.
Fix this by making the parameters pointers, stop reusing the macaddr
struct member, and documenting that NULL pointers mean unchanged.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the user rate mask results in no (basic) rates being usable,
clear it. Also, if we're already operating when it's set, reject
it instead.
Technically, selecting basic rates as the criterion is a bit too
restrictive, but calculating the usable rates over all stations
(e.g. in AP mode) is harder, and all stations must support the
basic rates. Similarly, in client mode, the basic rates will be
used anyway for control frames.
This fixes the "no supported rates (...) in rate_mask ..." warning
that occurs on TX when you've selected a rate mask that's not
compatible with the connection (e.g. an AP that enables only the
rates 36, 48, 54 and you've selected only 6, 9, 12.)
Reported-by: Kirtika Ruchandani <kirtika@google.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support .set_cqm_rssi_range_config if the beacons are available for
processing in mac80211. There's no reason that this couldn't be
offloaded by mac80211-based drivers but there's no driver method for
that added in this patch.
Signed-off-by: Andrew Zaborowski <andrew.zaborowski@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The nl80211_nan_dual_band_conf enumeration doesn't make much sense.
The default value is assigned to a bit, which makes it weird if the
default bit and other bits are set at the same time.
To improve this, get rid of NL80211_NAN_BAND_DEFAULT and add a wiphy
configuration to let the drivers define which bands are supported.
This is exposed to the userspace, which then can make a decision on
which band(s) to use. Additionally, rename all "dual_band" elements
to "bands", to make things clearer.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the ability for an AP (and associated VLANs) to perform
multicast-to-unicast conversion for ARP, IPv4 and IPv6 frames
(possibly within 802.1Q). If enabled, such frames are to be sent
to each station separately, with the DA replaced by their own
MAC address rather than the group address.
Note that this may break certain expectations of the receiver,
such as the ability to drop unicast IP packets received within
multicast L2 frames, or the ability to not send ICMP destination
unreachable messages for packets received in L2 multicast (which
is required, but the receiver can't tell the difference if this
new option is enabled.)
This also doesn't implement the 802.11 DMS (directed multicast
service).
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[use true/false, rename label to the correct "multicast",
use __be16 for ethertype and network order for constants]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As part of interface combination checking, verify any new
interface's beacon intervals. In fact, just always add the
beacon interval since that's harmless.
With this patch, mac80211 is prepared for drivers that set
the min_beacon_int_gcd parameter in interface combinations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This patch adds filtering for multicast data packets on AP_VLAN
interfaces that have no authorized station connected and changes
filtering on AP interfaces to not count stations assigned to
AP_VLAN interfaces.
This saves airtime and avoids waking up other stations currently
authorized in this BSS. When using WPA, the packets dropped could
not be decrypted by any station.
The behaviour when there are no AP_VLAN interfaces is left unchanged.
When there are AP_VLAN interfaces, this patch
1. adds filtering multicast data packets sent on AP_VLAN interfaces
that have no authorized station connected.
No filtering happens on 4addr AP_VLAN interfaces.
2. makes filtering of multicast data packets sent on AP interfaces
depend on the number of authorized stations in this bss not
assigned to an AP_VLAN interface.
Therefore, a new num_mcast_sta counter is added for AP_VLAN interfaces.
The existing one for AP interfaces is altered to not track stations
assigned to an AP_VLAN interface.
The new counter is exposed in debugfs.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[reformat commit message a bit, unline ieee80211_vif_{inc,dec}_num_mcast]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Checking for num_mcast_sta in __ieee80211_request_smps_ap() is
unnecessary as sta list will be empty in this case anyway, so
the list iteration will just exit immediately. Since this isn't
a "hot" code path, it doesn't really matter, and the next patch
will redefine num_mcast_sta to make this check invalid.
Signed-off-by: Michael Braun <michael-dev@fami-braun.de>
[change commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
sta_info_get_bss() is equivalent to sta_info_get() in the
mesh case, since sta->sdata->bss will be NULL (it's only
set for AP/AP_VLAN interfaces.) Thus, the mesh check here
isn't actually needed - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Provide an API to report NAN function match. Mac80211 will lookup the
corresponding cookie and report the match to cfg80211.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement add/rm_nan_func functions and handle NAN function
termination notifications. Handle instance_id allocation for
NAN functions and implement the reconfig flow.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Implement nan_change_conf callback which allows to change current
NAN configuration (master preference and dual band operation).
Store the current NAN configuration in sdata, so it can be used
both to provide the driver the updated configuration with changes
and also it will be used in hw reconfig flows in next patches.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This code doesn't do much besides allowing to start and
stop the vif.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This allows user space to start/stop NAN interface.
A NAN interface is like P2P device in a few aspects: it
doesn't have a netdev associated to it.
Add the new interface type and prevent operations that
can't be executed on NAN interface like scan.
Define several attributes that may be configured by user space
when starting NAN functionality (master preference and dual
band operation)
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If chanctx is derived as container_of() from a non-NULL pointer,
it can't ever be NULL. Since we checked conf before, that's true
here, so remove the useless NULL check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
add support to MU-MIMO air sniffer according groupID:
in monitor mode, use a given MU-MIMO groupID to monitor stations
that belongs to that group using MU-MIMO.
add support for following a station according to its MAC address
using VHT MU-MIMO sniffer:
the monitors wait until they get an action MU-MIMO notification
frame, then parses it in order to find the groupID that corresponds
to the given MAC address and monitors packets destined to that
groupID using VHT MU-MIMO.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Insert the u32 monitor flags variable in a new structure
that represents a monitor interface.
This will allow to add more configuration variables to
that structure which will happen in an upcoming change.
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The code currently assumes that buffered multicast PS frames don't have
a pending ACK frame for tx status reporting.
However, hostapd sends a broadcast deauth frame on teardown for which tx
status is requested. This can lead to the "Have pending ack frames"
warning on module reload.
Fix this by using ieee80211_free_txskb/ieee80211_purge_tx_queue.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Previously, mesh power management functionality works only with kernel
MPM. Because user space MPM did not report mesh peer AID to kernel,
the kernel could not identify the bit in TIM element. So this patch
adds mesh peer AID setting API.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The regular RX path has a lot of code, but with a few
assumptions on the hardware it's possible to reduce the
amount of code significantly. Currently the assumptions
on the driver are the following:
* hardware/driver reordering buffer (if supporting aggregation)
* hardware/driver decryption & PN checking (if using encryption)
* hardware/driver did de-duplication
* hardware/driver did A-MSDU deaggregation
* AP_LINK_PS is used (in AP mode)
* no client powersave handling in mac80211 (in client mode)
of which some are actually checked per packet:
* de-duplication
* PN checking
* decryption
and additionally packets must
* not be A-MSDU (have been deaggregated by driver/device)
* be data packets
* not be fragmented
* be unicast
* have RFC 1042 header
Additionally dynamically we assume:
* no encryption or CCMP/GCMP, TKIP/WEP/other not allowed
* station must be authorized
* 4-addr format not enabled
Some data needed for the RX path is cached in a new per-station
"fast_rx" structure, so that we only need to look at this and
the packet, no other memory when processing packets on the fast
RX path.
After doing the above per-packet checks, the data path collapses
down to a pretty simple conversion function taking advantage of
the data cached in the small fast_rx struct.
This should speed up the RX processing, and will make it easier
to reason about parallelizing RX (for which statistics will need
to be per-CPU still.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Legacy clients don't support P2P power save mechanism, and thus if a P2P GO
has a legacy client connected to it, it should disable P2P PS mechanisms.
Let the driver know about this with a new bss_conf parameter.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Shaul Triebitz