Add a helper that answers the cell size of the devlink device.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing pool type from static to dynamic causes reinterpretation of
threshold values. They therefore need to be saved before pool type is
changed, then the pool type can be changed, and then the new values need
to be set up.
For that reason, set cannot subsume save, because it would be saving the
wrong thing, with possibly a nonsensical value, and restore would then fail
to restore the nonsensical value.
Thus extract a _save() from each of the relevant _set()'s. This way it is
possible to save everything up front, then to tweak it, and then restore in
the required order.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One issue was reported at a baremetal environment, which is used for
FPGA verification. "The first transfer will fail for extended ID
format(for both 2.0B and FD format), following frames can be transmitted
and received successfully for extended format, and standard format don't
have this issue. This issue occurred randomly with high possiblity, when
it occurs, the transmitter will detect a BIT1 error, the receiver a CRC
error. According to the spec, a non-correctable error may cause this
transfer failure."
With FLEXCAN_QUIRK_DISABLE_MECR quirk, it supports correctable errors,
disable non-correctable errors interrupt and freeze mode. Platform has
ECC hardware support, but select this quirk, this issue may not come to
light. Initialize all FlexCAN memory before accessing them, at least it
can avoid non-correctable errors detected due to memory uninitialized.
The internal region can't be initialized when the hardware doesn't support
ECC.
According to IMX8MPRM, Rev.C, 04/2020. There is a NOTE at the section
11.8.3.13 Detection and correction of memory errors:
"All FlexCAN memory must be initialized before starting its operation in
order to have the parity bits in memory properly updated. CTRL2[WRMFRZ]
grants write access to all memory positions that require initialization,
ranging from 0x080 to 0xADF and from 0xF28 to 0xFFF when the CAN FD feature
is enabled. The RXMGMASK, RX14MASK, RX15MASK, and RXFGMASK registers need to
be initialized as well. MCR[RFEN] must not be set during memory initialization."
Memory range from 0x080 to 0xADF, there are reserved memory (unimplemented
by hardware, e.g. only configure 64 MBs), these memory can be initialized or not.
In this patch, initialize all flexcan memory which includes reserved memory.
In this patch, create FLEXCAN_QUIRK_SUPPORT_ECC for platforms which has ECC
feature. If you have a ECC platform in your hand, please select this
qurik to initialize all flexcan memory firstly, then you can select
FLEXCAN_QUIRK_DISABLE_MECR to only enable correctable errors.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20200929211557.14153-2-qiangqing.zhang@nxp.com
[mkl: wrap long lines]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In [1] Geert noted that the autodetect compatible for the mcp25xxfd driver,
which is "microchip,mcp25xxfd" might be too generic and overlap with upcoming,
but incompatible chips.
In the previous patch the autodetect DT compatbile has been renamed to
"microchip,mcp251xfd", this patch changes all user facing strings from
"mcp25xxfd" to "mcp251xfd" and "MCP25XXFD" to "MCP251XFD", including:
- kconfig symbols
- name of kernel module
- DT and SPI compatible
[1] http://lore.kernel.org/r/CAMuHMdVkwGjr6dJuMyhQNqFoJqbh6Ec5V2b5LenCshwpM2SDsQ@mail.gmail.com
Link: https://lore.kernel.org/r/20200930091424.792165-9-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Add test validating that btf_dump works fine with BTFs that are modified and
incrementally generated.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200929232843.1249318-5-andriin@fb.com
Ensure that btf_dump can accommodate new BTF types being appended to BTF
instance after struct btf_dump was created. This came up during attemp to
use btf_dump for raw type dumping in selftests, but given changes are not
excessive, it's good to not have any gotchas in API usage, so I decided to
support such use case in general.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200929232843.1249318-2-andriin@fb.com
Daniel Borkmann says:
====================
This series adds two BPF helpers, that is, one for retrieving the classid
of an skb and another one to redirect via the neigh subsystem, and improves
also the cookie helpers by removing the atomic counter. I've also added
the bpf_tail_call_static() helper to the libbpf API that we've been using
in Cilium for a while now, and last but not least the series adds a few
selftests. For details, please check individual patches, thanks!
v3 -> v4:
- Removed out_rec error path (Martin)
- Integrate BPF_F_NEIGH flag into rejecting invalid flags (Martin)
- I think this way it's better to avoid bit overlaps given it's
right in the place that would need to be extended on new flags
v2 -> v3:
- Removed double skb->dev = dev assignment (David)
- Added headroom check for v6 path (David)
- Set set flowi4_proto for ip_route_output_flow (David)
- Rebased onto latest bpf-next
v1 -> v2:
- Rework cookie generator to support nested contexts (Eric)
- Use ip_neigh_gw6() and container_of() (David)
- Rename __throw_build_bug() and improve comments (Andrii)
- Use bpf_tail_call_static() also in BPF samples (Maciej)
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Port of tail_call_static() helper function from Cilium's BPF code base [0]
to libbpf, so others can easily consume it as well. We've been using this
in production code for some time now. The main idea is that we guarantee
that the kernel's BPF infrastructure and JIT (here: x86_64) can patch the
JITed BPF insns with direct jumps instead of having to fall back to using
expensive retpolines. By using inline asm, we guarantee that the compiler
won't merge the call from different paths with potentially different
content of r2/r3.
We're also using Cilium's __throw_build_bug() macro (here as: __bpf_unreachable())
in different places as a neat trick to trigger compilation errors when
compiler does not remove code at compilation time. This works for the BPF
back end as it does not implement the __builtin_trap().
[0] f5537c2602
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Link: https://lore.kernel.org/bpf/1656a082e077552eb46642d513b4a6bde9a7dd01.1601477936.git.daniel@iogearbox.net
Add a redirect_neigh() helper as redirect() drop-in replacement
for the xmit side. Main idea for the helper is to be very similar
in semantics to the latter just that the skb gets injected into
the neighboring subsystem in order to let the stack do the work
it knows best anyway to populate the L2 addresses of the packet
and then hand over to dev_queue_xmit() as redirect() does.
This solves two bigger items: i) skbs don't need to go up to the
stack on the host facing veth ingress side for traffic egressing
the container to achieve the same for populating L2 which also
has the huge advantage that ii) the skb->sk won't get orphaned in
ip_rcv_core() when entering the IP routing layer on the host stack.
Given that skb->sk neither gets orphaned when crossing the netns
as per 9c4c325252 ("skbuff: preserve sock reference when scrubbing
the skb.") the helper can then push the skbs directly to the phys
device where FQ scheduler can do its work and TCP stack gets proper
backpressure given we hold on to skb->sk as long as skb is still
residing in queues.
With the helper used in BPF data path to then push the skb to the
phys device, I observed a stable/consistent TCP_STREAM improvement
on veth devices for traffic going container -> host -> host ->
container from ~10Gbps to ~15Gbps for a single stream in my test
environment.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: David Ahern <dsahern@gmail.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Cc: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/bpf/f207de81629e1724899b73b8112e0013be782d35.1601477936.git.daniel@iogearbox.net
With its use in BPF, the cookie generator can be called very frequently
in particular when used out of cgroup v2 hooks (e.g. connect / sendmsg)
and attached to the root cgroup, for example, when used in v1/v2 mixed
environments. In particular, when there's a high churn on sockets in the
system there can be many parallel requests to the bpf_get_socket_cookie()
and bpf_get_netns_cookie() helpers which then cause contention on the
atomic counter.
As similarly done in f991bd2e14 ("fs: introduce a per-cpu last_ino
allocator"), add a small helper library that both can use for the 64 bit
counters. Given this can be called from different contexts, we also need
to deal with potential nested calls even though in practice they are
considered extremely rare. One idea as suggested by Eric Dumazet was
to use a reverse counter for this situation since we don't expect 64 bit
overflows anyways; that way, we can avoid bigger gaps in the 64 bit
counter space compared to just batch-wise increase. Even on machines
with small number of cores (e.g. 4) the cookie generation shrinks from
min/max/med/avg (ns) of 22/50/40/38.9 down to 10/35/14/17.3 when run
in parallel from multiple CPUs.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Link: https://lore.kernel.org/bpf/8a80b8d27d3c49f9a14e1d5213c19d8be87d1dc8.1601477936.git.daniel@iogearbox.net
Similarly to 5a52ae4e32 ("bpf: Allow to retrieve cgroup v1 classid
from v2 hooks"), add a helper to retrieve cgroup v1 classid solely
based on the skb->sk, so it can be used as key as part of BPF map
lookups out of tc from host ns, in particular given the skb->sk is
retained these days when crossing net ns thanks to 9c4c325252
("skbuff: preserve sock reference when scrubbing the skb."). This
is similar to bpf_skb_cgroup_id() which implements the same for v2.
Kubernetes ecosystem is still operating on v1 however, hence net_cls
needs to be used there until this can be dropped in with the v2
helper of bpf_skb_cgroup_id().
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/ed633cf27a1c620e901c5aa99ebdefb028dce600.1601477936.git.daniel@iogearbox.net
The NoMMU kernel is broken for QEMU virt machine from Linux-5.9-rc6
because clint_time_val is used even before CLINT driver is probed
at following places:
1. rand_initialize() calls get_cycles() which in-turn uses
clint_time_val
2. boot_init_stack_canary() calls get_cycles() which in-turn
uses clint_time_val
The issue#1 (above) is fixed by providing custom random_get_entropy()
for RISC-V NoMMU kernel. For issue#2 (above), we remove dependency of
boot_init_stack_canary() on get_cycles() and this is aligned with the
boot_init_stack_canary() implementations of ARM, ARM64 and MIPS kernel.
Fixes: d5be89a8d1 ("RISC-V: Resurrect the MMIO timer implementation for M-mode systems")
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
We use a device's allocation state tree to track ranges in a device used
for allocated chunks, and we set ranges in this tree when allocating a new
chunk. However after a device replace operation, we were not setting the
allocated ranges in the new device's allocation state tree, so that tree
is empty after a device replace.
This means that a fitrim operation after a device replace will trim the
device ranges that have allocated chunks and extents, as we trim every
range for which there is not a range marked in the device's allocation
state tree. It is also important during chunk allocation, since the
device's allocation state is used to determine if a range is already
allocated when allocating a new chunk.
This is trivial to reproduce and the following script triggers the bug:
$ cat reproducer.sh
#!/bin/bash
DEV1="/dev/sdg"
DEV2="/dev/sdh"
DEV3="/dev/sdi"
wipefs -a $DEV1 $DEV2 $DEV3 &> /dev/null
# Create a raid1 test fs on 2 devices.
mkfs.btrfs -f -m raid1 -d raid1 $DEV1 $DEV2 > /dev/null
mount $DEV1 /mnt/btrfs
xfs_io -f -c "pwrite -S 0xab 0 10M" /mnt/btrfs/foo
echo "Starting to replace $DEV1 with $DEV3"
btrfs replace start -B $DEV1 $DEV3 /mnt/btrfs
echo
echo "Running fstrim"
fstrim /mnt/btrfs
echo
echo "Unmounting filesystem"
umount /mnt/btrfs
echo "Mounting filesystem in degraded mode using $DEV3 only"
wipefs -a $DEV1 $DEV2 &> /dev/null
mount -o degraded $DEV3 /mnt/btrfs
if [ $? -ne 0 ]; then
dmesg | tail
echo
echo "Failed to mount in degraded mode"
exit 1
fi
echo
echo "File foo data (expected all bytes = 0xab):"
od -A d -t x1 /mnt/btrfs/foo
umount /mnt/btrfs
When running the reproducer:
$ ./replace-test.sh
wrote 10485760/10485760 bytes at offset 0
10 MiB, 2560 ops; 0.0901 sec (110.877 MiB/sec and 28384.5216 ops/sec)
Starting to replace /dev/sdg with /dev/sdi
Running fstrim
Unmounting filesystem
Mounting filesystem in degraded mode using /dev/sdi only
mount: /mnt/btrfs: wrong fs type, bad option, bad superblock on /dev/sdi, missing codepage or helper program, or other error.
[19581.748641] BTRFS info (device sdg): dev_replace from /dev/sdg (devid 1) to /dev/sdi started
[19581.803842] BTRFS info (device sdg): dev_replace from /dev/sdg (devid 1) to /dev/sdi finished
[19582.208293] BTRFS info (device sdi): allowing degraded mounts
[19582.208298] BTRFS info (device sdi): disk space caching is enabled
[19582.208301] BTRFS info (device sdi): has skinny extents
[19582.212853] BTRFS warning (device sdi): devid 2 uuid 1f731f47-e1bb-4f00-bfbb-9e5a0cb4ba9f is missing
[19582.213904] btree_readpage_end_io_hook: 25839 callbacks suppressed
[19582.213907] BTRFS error (device sdi): bad tree block start, want 30490624 have 0
[19582.214780] BTRFS warning (device sdi): failed to read root (objectid=7): -5
[19582.231576] BTRFS error (device sdi): open_ctree failed
Failed to mount in degraded mode
So fix by setting all allocated ranges in the replace target device when
the replace operation is finishing, when we are holding the chunk mutex
and we can not race with new chunk allocations.
A test case for fstests follows soon.
Fixes: 1c11b63eff ("btrfs: replace pending/pinned chunks lists with io tree")
CC: stable@vger.kernel.org # 5.2+
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
The commit eb1f00237a ("lockdep,trace: Expose tracepoints"), started to
expose us for tracepoints. For imx6q cpuidle, this leads to an RCU splat
according to below.
[6.870684] [<c0db7690>] (_raw_spin_lock) from [<c011f6a4>] (imx6q_enter_wait+0x18/0x9c)
[6.878846] [<c011f6a4>] (imx6q_enter_wait) from [<c09abfb0>] (cpuidle_enter_state+0x168/0x5e4)
To fix the problem, let's assign the corresponding idlestate->flags the
CPUIDLE_FLAG_RCU_IDLE bit, which enables us to call rcu_idle_enter|exit()
at the proper point.
Reported-by: Dong Aisheng <aisheng.dong@nxp.com>
Suggested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix a reStructuredText syntax error in the cpuidle PM admin-guide
documentation: the ``...'' quotation marks are parsed as partial ''...''
reStructuredText markup and break the output formatting.
This change them to "...".
Signed-off-by: Yoann Congal <yoann.congal@smile.fr>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fix missing return statement when writing "off" to intel_pstate status
sysfs I/F.
Fixes: 55671ea325 ("cpufreq: intel_pstate: Free memory only when turning off")
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the driver initializes in safe mode, it will call
ice_set_safe_mode_caps. This results in clearing the capabilities
structures, in order to set them up for operating in safe mode, ensuring
many features are disabled.
This has a side effect of also clearing the capability bits that relate
to NVM update. The result is that the device driver will not indicate
support for unified update, even if the firmware is capable.
Fix this by adding the relevant capability fields to the list of values
we preserve. To simplify the code, use a common_cap structure instead of
a handful of local variables. To reduce some duplication of the
capability name, introduce a couple of macros used to restore the
capabilities values from the cached copy.
Fixes: de9b277ee0 ("ice: Add support for unified NVM update flow capability")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The ice driver needs to wait for a firmware response to each command to
write a block of data to the scratch area used to update the device
firmware. The driver currently waits for up to 1 second for this to be
returned.
It turns out that firmware might take longer than 1 second to return
a completion in some cases. If this happens, the flash update will fail
to complete.
Fix this by increasing the maximum time that the driver will wait for
both writing a block of data, and for activating the new NVM bank. The
timeout for an erase command is already several minutes, as the firmware
had to erase the entire bank which was already expected to take a minute
or more in the worst case.
In the case where firmware really won't respond, we will now take longer
to fail. However, this ensures that if the firmware is simply slow to
respond, the flash update can still complete. This new maximum timeout
should not adversely increase the update time, as the implementation for
wait_event_interruptible_timeout, and should wake very soon after we get
a completion event. It is better for a flash update be slow but still
succeed than to fail because we gave up too quickly.
Fixes: d69ea414c9 ("ice: implement device flash update via devlink")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brijesh Behera <brijeshx.behera@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
gfxoff is temporarily disabled for navy_flounder, since
at present the feature caused some tdr when performing
display operations.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
As the dpm clock table is needed during DC HW initialization.
And that (DC HW initialization) comes before smu_late_init()
where current APU dpm clock table setup is performed. So, NULL
pointer dereference will be triggered. By moving APU dpm clock
table setup to smu_hw_init(), this can be avoided.
Fixes: 02cf91c113 ("drm/amd/powerplay: postpone operations not required for hw setup to late_init")
Acked-by: Nirmoy Das <nirmoy.das@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reported-by: Dirk Gouders <dirk@gouders.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enables storing userdata for nft_chain. Field udata points to user data
and udlen stores its length.
Adds new attribute flag NFTA_CHAIN_USERDATA.
Signed-off-by: Jose M. Guisado Gomez <guigom@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When userdata support was added to tables and objects, user data coming
from user space was allocated and copied using kzalloc + nla_memcpy.
Use nla_memdup to copy userdata of tables and objects.
Signed-off-by: Jose M. Guisado Gomez <guigom@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When userdata was introduced for tables and objects its allocation was
only freed inside the error path of the new{table, object} functions.
Free user data inside corresponding destroy functions for tables and
objects.
Fixes: b131c96496 ("netfilter: nf_tables: add userdata support for nft_object")
Fixes: 7a81575b80 ("netfilter: nf_tables: add userdata attributes to nft_table")
Signed-off-by: Jose M. Guisado Gomez <guigom@riseup.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Alexei Starovoitov says:
====================
pull-request: bpf 2020-09-29
The following pull-request contains BPF updates for your *net* tree.
We've added 7 non-merge commits during the last 14 day(s) which contain
a total of 7 files changed, 28 insertions(+), 8 deletions(-).
The main changes are:
1) fix xdp loading regression in libbpf for old kernels, from Andrii.
2) Do not discard packet when NETDEV_TX_BUSY, from Magnus.
3) Fix corner cases in libbpf related to endianness and kconfig, from Tony.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Apply following fixes:
- Use 'interrupts'. (interrupts-extended will automagically be supported
by the tools)
- *-supply is always a single item. So, drop maxItems=1
- add "additionalProperties: false" flag to detect unneeded properties.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20200923125301.27200-1-o.rempel@pengutronix.de
Reported-by: Rob Herring <robh@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Fixes: 1b5a78e69c ("dt-binding: can: mcp25xxfd: document device tree bindings")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the following warning:
drivers/net/can/spi/mcp25xxfd/mcp25xxfd-core.c:2155 mcp25xxfd_irq()
error: uninitialized symbol 'set_normal_mode'.
by adding the missing initialization.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Link: https://lore.kernel.org/r/20200923114726.2704426-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This loop doesn't free the first element of the array. The "i > 0" has
to be changed to "i >= 0".
Fixes: 55e5b97f00 ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200923112752.GA1473821@mwanda
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a reference to the recent released MCP2517FD and MCP2518FD
errata sheets and paste the explanation.
The driver already implements the proposed fix.
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
Link: https://lore.kernel.org/r/20200925065606.358-1-thomas.kopp@microchip.com
[mkl: split into two patches, adjust subject and commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds a reference to the recent released MCP2517FD and MCP2518FD
errata sheets and paste the explanation.
The single error correction does not always work, so always indicate that a
single error occurred. If the location of the ECC error is outside of the
TX-RAM always use netdev_notice() to log the problem. For ECC errors in the
TX-RAM, there is a recovery procedure.
Signed-off-by: Thomas Kopp <thomas.kopp@microchip.com>
Link: https://lore.kernel.org/r/20200925065606.358-1-thomas.kopp@microchip.com
[mkl: split into two patches, adjust subject and commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
clint_time_val will soon be used by the RISC-V implementation of
random_get_entropy(), which is a static inline function that may be used by
modules (at least CRYPTO_JITTERENTROPY=m).
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Palmer Dabbelt <palmerdabbelt@google.com>
ttm_mem_type_manager_func.get_node was changed to return -ENOSPC
instead of setting the node pointer to NULL. Unfortunately
vmwgfx still had two places where it was explicitly converting
-ENOSPC to 0 causing regressions. This fixes those spots by
allowing -ENOSPC to be returned. That seems to fix recent
regressions with vmwgfx.
Signed-off-by: Zack Rusin <zackr@vmware.com>
Reviewed-by: Roland Scheidegger <sroland@vmware.com>
Reviewed-by: Martin Krastev <krastevm@vmware.com>
Sigend-off-by: Roland Scheidegger <sroland@vmware.com>
The kernel may fail to boot or devices may fail to come up when
initializing iscsi_tcp devices starting with Linux 5.8.
Commit a79af8a64d ("[SCSI] iscsi_tcp: use iscsi_conn_get_addr_param
libiscsi function") introduced getpeername() within the session spinlock.
Commit 1b66d25361 ("bpf: Add get{peer, sock}name attach types for
sock_addr") introduced BPF_CGROUP_RUN_SA_PROG_LOCK() within getpeername(),
which acquires a mutex and when used from iscsi_tcp devices can now lead to
"BUG: scheduling while atomic:" and subsequent damage.
Ensure that the spinlock is released before calling getpeername() or
getsockname(). sock_hold() and sock_put() are used to ensure that the
socket reference is preserved until after the getpeername() or
getsockname() complete.
Link: https://bugzilla.redhat.com/show_bug.cgi?id=1877345
Link: https://lkml.org/lkml/2020/7/28/1085
Link: https://lkml.org/lkml/2020/8/31/459
Link: https://lore.kernel.org/r/20200928043329.606781-1-mark.mielke@gmail.com
Fixes: a79af8a64d ("[SCSI] iscsi_tcp: use iscsi_conn_get_addr_param libiscsi function")
Fixes: 1b66d25361 ("bpf: Add get{peer, sock}name attach types for sock_addr")
Cc: stable@vger.kernel.org
Reported-by: Marc Dionne <marc.c.dionne@gmail.com>
Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Mark Mielke <mark.mielke@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Vladimir Oltean says:
====================
HW support for VCAP IS1 and ES0 in mscc_ocelot
The patches from RFC series "Offload tc-flower to mscc_ocelot switch
using VCAP chains" have been split into 2:
https://patchwork.ozlabs.org/project/netdev/list/?series=204810&state=*
This is the boring part, that deals with the prerequisites, and not with
tc-flower integration. Apart from the initialization of some hardware
blocks, which at this point still don't do anything, no new
functionality is introduced.
- Key and action field offsets are defined for the supported switches.
- VCAP properties are added to the driver for the new TCAM blocks. But
instead of adding them manually as was done for IS2, which is error
prone, the driver is refactored to read these parameters from
hardware, which is possible.
- Some improvements regarding the processing of struct ocelot_vcap_filter.
- Extending the code to be compatible with full and quarter keys.
This series was tested, along with other patches not yet submitted, on
the Felix and Seville switches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently a new filter is created, containing just enough correct
information to be able to call ocelot_vcap_block_find_filter_by_index()
on it.
This will be limiting us in the future, when we'll have more metadata
associated with a filter, which will matter in the stats() and destroy()
callbacks, and which we can't make up on the spot. For example, we'll
start "offloading" some dummy tc filter entries for the TCAM skeleton,
but we won't actually be adding them to the hardware, or to block->rules.
So, it makes sense to avoid deleting those rules too. That's the kind of
thing which is difficult to determine unless we look up the real filter.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And rename the existing find to ocelot_vcap_block_find_filter_by_index.
The index is the position in the TCAM, and the id is the flow cookie
given by tc.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'cnt' variable is actually used for 2 purposes, to hold the number
of sub-words per VCAP entry, and the number of sub-words per VCAP
action.
In fact, I'm pretty sure these 2 numbers can never be different from one
another. By hardware definition, the entry (key) TCAM rows are divided
into the same number of sub-words as its associated action RAM rows.
But nonetheless, let's at least rename the variables such that
observations like this one are easier to make in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This gets rid of one of the 2 variables named, very generically,
"count".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calculating the offsets for the current entry within the row and
placing them inside struct vcap_data, the function assumes half key
entry (2 keys per row).
This patch modifies the vcap_data_offset_get() function to calculate a
correct data offset when the setting VCAP Type-Group of a key to
VCAP_TG_FULL or VCAP_TG_QUARTER.
This is needed because, for example, VCAP ES0 only supports full keys.
Also rename the 'count' variable to 'num_entries_per_row' to make the
function just one tiny bit easier to follow.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr Machata