The System Controller Firmware (SCFW) is a low-level system function
which runs on a dedicated Cortex-M core to provide power, clock, and
resource management. It exists on some i.MX8 processors. e.g. i.MX8QM
(QM, QP), and i.MX8QX (QXP, DX). SCU driver manages the IPC interface
between host CPU and the SCU firmware running on M4.
For i.MX8QM, stop mode request is controlled by System Controller Unit(SCU)
firmware, this patch introduces FLEXCAN_QUIRK_SETUP_STOP_MODE_SCFW quirk
for this function.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20201106105627.31061-6-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
For SoCs with SCU support, need setup stop mode via SCU firmware, so this
property can help indicate a resource in SCU firmware.
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Link: https://lore.kernel.org/r/20201106105627.31061-3-qiangqing.zhang@nxp.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Multiple filters (struct can_filter) can be set with the setsockopt()
function, which was originally intended as a write-only operation.
As getsockopt() also provides a CAN_RAW_FILTER option to read back the
given filters, the caller has to provide an appropriate user space buffer.
In the case this buffer is too small the getsockopt() silently truncates
the filter information and gives no information about the needed space.
This is safe but not convenient for the programmer.
In net/core/sock.c the SO_PEERGROUPS sockopt had a similar requirement
and solved it by returning -ERANGE in the case that the provided data
does not fit into the given user space buffer and fills the required size
into optlen, so that the caller can retry with a matching buffer length.
This patch adopts this approach for CAN_RAW_FILTER getsockopt().
Reported-by: Phillip Schichtel <phillip@schich.tel>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-By: Phillip Schichtel <phillip@schich.tel>
Link: https://lore.kernel.org/r/20201216174928.21663-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds back support for half-duplex controllers, which was removed in
the last patch.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-17-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch reworks the SPI access and fixes several probems:
- tcan4x5x_regmap_gather_write(), tcan4x5x_regmap_read():
Do not place variable "addr" on stack and use it as buffer for SPI
transfer. Buffers for SPI transfers must be allocated from DMA save
memory.
- tcan4x5x_regmap_gather_write(), tcan4x5x_regmap_read():
Halfe number of SPI transfers by using a single buffer + memcpy().
This improves the performance, especially on SPI controllers, which
use interrupt based transfers.
- Use "8" bits per word, not "32". This makes it possible to use this
driver on SoCs like the Raspberry Pi, which SPI host controller
drivers only support 8 bits per word.
Note: this breaks half duplex only controllers. Support for them will be
re-added in the next patch.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-16-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The memory space of the chip is not fully populated, so add a regmap range
table to document this.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-15-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The tcan4x5x chip support bulk read/write, but as the length field is only 8
bits wide, the maximum is 256. A length of 0 is treated as 256.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-14-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch sets the regmap stide to 4, as the chip only supports access on 32
bit alligned access.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-13-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch replaces the context pointer of the regmap callback functions by a
pointer to the spi_device. This saves one level of indirection in the
callbacks.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-11-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch simplifies the tcan4x5x_regmap_write(0 function by removing not
needed casts and replaces hardcoded "4" by appropriate sizeof()s.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-10-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch renames the regmap_spi_gather_write() function to
tcan4x5x_regmap_gather_write(). Now it has a "tcan4x5x_" prefix as all other
functions in this driver.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-9-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The driver doesn't use regmap async support, so remove the stubs.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-8-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With C99 initializers, all non mentioned members are initialzied to 0, so
remove not needed initialization of read_flag_mask.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-7-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch marks the struct regmap_bus tcan4x5x_bus as constant.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a preparation patch to move the regmap related code into a seperate
file. This patch removes the tcan4x5x.c to tcan4x5x-core.c.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-4-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch beautifies the indention of the tcan4x5x_of_match and
tcan4x5x_id_table.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch replaces the DEVICE_NAME macro by KBUILD_MODNAME and removed the
superfluous DEVICE_NAME.
Reviewed-by: Dan Murphy <dmurphy@ti.com>
Tested-by: Sean Nyekjaer <sean@geanix.com>
Link: https://lore.kernel.org/r/20201215231746.1132907-2-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The kernel image can contain multiple types (structs/unions)
with the same name. This causes distinct type hierarchies in
BTF data and makes resolve_btfids fail with error like:
BTFIDS vmlinux
FAILED unresolved symbol udp6_sock
as reported by Qais Yousef [1].
This change adds warning when multiple types of the same name
are detected:
BTFIDS vmlinux
WARN: multiple IDs found for 'file': 526, 113351 - using 526
WARN: multiple IDs found for 'sk_buff': 2744, 113958 - using 2744
We keep the lower ID for the given type instance and let the
build continue.
Also changing the 'nr' variable name to 'nr_types' to avoid confusion.
[1] https://lore.kernel.org/lkml/20201229151352.6hzmjvu3qh6p2qgg@e107158-lin/
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210105234219.970039-1-jolsa@kernel.org
This patch fixes some spelling typos in snmp_counter.rst
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Marek Vasut says:
====================
net: ks8851: Add KS8851 PHY support
The KS8851 has a reduced internal PHY, which is accessible through its
registers at offset 0xe4. The PHY is compatible with KS886x PHY present
in Micrel switches, including the PHY ID Low/High registers swap, which
is present both in the MAC and the switch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The KS8851 has a reduced internal PHY, which is accessible through its
registers at offset 0xe4. The PHY is compatible with KS886x PHY present
in Micrel switches, except the PHY ID Low/High registers are swapped.
Register MDIO bus so this PHY can be detected and probed by phylib.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KS8851 has a reduced internal PHY, which is accessible through its
registers at offset 0xe4. The PHY is compatible with KS886x PHY present
in Micrel switches, including the PHY ID Low/High registers swap, which
is present both in the MAC and the switch.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The udpgro.sh will always return 0 (unless the bpf selftest was not
build first) even if there are some failed sub test-cases.
Therefore the kselftest framework will report this case is OK.
Check and return the exit status of each test to make it easier to
spot real failures.
Signed-off-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 1d6cd39293 ("modpost: turn missing MODULE_LICENSE()
into error") the ppc32_allmodconfig build fails with:
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-fec.o
ERROR: modpost: missing MODULE_LICENSE() in drivers/net/ethernet/freescale/fs_enet/mii-bitbang.o
Add the missing MODULE_LICENSEs to fix the build. Both files include a
copyright header indicating they are GPL v2.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because macvlan_common_newlink() and macvlan_changelink() already
checked NULL data parameter, so the additional check is unnecessary,
just remove it.
Fixes: 79cf79abce ("macvlan: add source mode")
Signed-off-by: Yunjian Wang <wangyunjian@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A null-ptr-deref bug is reported by Hulk Robot like this:
--------------
KASAN: null-ptr-deref in range [0x0000000000000128-0x000000000000012f]
Call Trace:
qrtr_ns_remove+0x22/0x40 [ns]
qrtr_proto_fini+0xa/0x31 [qrtr]
__x64_sys_delete_module+0x337/0x4e0
do_syscall_64+0x34/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xa9
RIP: 0033:0x468ded
--------------
When qrtr_ns_init fails in qrtr_proto_init, qrtr_ns_remove which would
be called later on would raise a null-ptr-deref because qrtr_ns.workqueue
has been destroyed.
Fix it by making qrtr_ns_init have a return value and adding a check in
qrtr_proto_init.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Aligning to tx_ndp_modulus is not sufficient because the next align
call can be cdc_ncm_align_tail, which can add up to ctx->tx_modulus +
ctx->tx_remainder - 1 bytes. This used to lead to occasional crashes
on a Huawei 909s-120 LTE module as follows:
- the condition marked /* if there is a remaining skb [...] */ is true
so the swaps happen
- skb_out is set from ctx->tx_curr_skb
- skb_out->len is exactly 0x3f52
- ctx->tx_curr_size is 0x4000 and delayed_ndp_size is 0xac
(note that the sum of skb_out->len and delayed_ndp_size is 0x3ffe)
- the for loop over n is executed once
- the cdc_ncm_align_tail call marked /* align beginning of next frame */
increases skb_out->len to 0x3f56 (the sum is now 0x4002)
- the condition marked /* check if we had enough room left [...] */ is
false so we break out of the loop
- the condition marked /* If requested, put NDP at end of frame. */ is
true so the NDP is written into skb_out
- now skb_out->len is 0x4002, so padding_count is minus two interpreted
as an unsigned number, which is used as the length argument to memset,
leading to a crash with various symptoms but usually including
> Call Trace:
> <IRQ>
> cdc_ncm_fill_tx_frame+0x83a/0x970 [cdc_ncm]
> cdc_mbim_tx_fixup+0x1d9/0x240 [cdc_mbim]
> usbnet_start_xmit+0x5d/0x720 [usbnet]
The cdc_ncm_align_tail call first aligns on a ctx->tx_modulus
boundary (adding at most ctx->tx_modulus-1 bytes), then adds
ctx->tx_remainder bytes. Alternatively, the next alignment call can
occur in cdc_ncm_ndp16 or cdc_ncm_ndp32, in which case at most
ctx->tx_ndp_modulus-1 bytes are added.
A similar problem has occurred before, and the code is nontrivial to
reason about, so add a guard before the crashing call. By that time it
is too late to prevent any memory corruption (we'll have written past
the end of the buffer already) but we can at least try to get a warning
written into an on-disk log by avoiding the hard crash caused by padding
past the buffer with a huge number of zeros.
Signed-off-by: Jouni K. Seppänen <jks@iki.fi>
Fixes: 4a0e3e989d ("cdc_ncm: Add support for moving NDP to end of NCM frame")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=209407
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huazhong Tan says:
====================
net: hns3: fixes for -net
There are some bugfixes for the HNS3 ethernet driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
For DEVICE_VERSION_V2, the hardware only supports src-ip,
dst-ip and verification-tag for rss tuple set of sctp6
packet. For DEVICE_VERSION_V3, the hardware supports
src-port and dst-port as well.
Currently, when user queries the sctp6 rss tuples info,
some unsupported information will be showed on V2. So add
a check for hardware version when initializing and queries
sctp6 rss tuple to fix this issue.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HCLGE_MBX_MAX_ARQ_MSG_NUM is used to apply memory for the number
of queues used by ARQ(Asynchronous Receive Queue), so the head
and tail pointers should also use this macro.
Fixes: 07a0556a3a ("net: hns3: Changes to support ARQ(Asynchronous Receive Queue)")
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When phy driver does not implement the set_loopback interface,
phy loopback test will return -EOPNOTSUPP, and the loopback test
will fail. So when phy driver does not implement the set_loopback
interface, don't do phy loopback test.
Fixes: c9765a89d1 ("net: hns3: add phy selftest function")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix calling context.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware supports 8 RSS groups per interface. Currently we are using
only group '0'. This patch allows user to create new RSS groups/contexts
and use the same as destination for flow steering rules.
usage:
To steer the traffic to RQ 2,3
ethtool -X eth0 weight 0 0 1 1 context new
(It will print the allocated context id number)
New RSS context is 1
ethtool -N eth0 flow-type tcp4 dst-port 80 context 1 loc 1
To delete the context
ethtool -X eth0 context 1 delete
When an RSS context is removed, the active classification
rules using this context are also removed.
Change-log:
v4
- Fixed compiletime warning.
- Address Saeed's comments on v3.
v3
- Coverted otx2_set_rxfh() to use new function.
v2
- Removed unrelated whitespace
- Coverted otx2_get_rxfh() to use new function.
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Samuel Holland says:
====================
Fixes for dwmac-sun8i suspend/resume
This series fixes issues preventing dwmac-sun8i from working after a
suspend/resume cycle. Those issues include the PHY being left powered
off, the MAC syscon configuration being reset, and the reference to the
reset controller being improperly dropped. They also fix related issues
in probe error handling and driver removal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, sun8i_dwmac_set_syscon was called from a chain of functions
in several different files:
sun8i_dwmac_probe
stmmac_dvr_probe
stmmac_hw_init
stmmac_hwif_init
sun8i_dwmac_setup
sun8i_dwmac_set_syscon
which made the lifetime of the syscon values hard to reason about. Part
of the problem is that there is no similar platform driver callback from
stmmac_dvr_remove. As a result, the driver unset the syscon value in
sun8i_dwmac_exit, but this leaves it uninitialized after a suspend/
resume cycle. It was also unset a second time (outside sun8i_dwmac_exit)
in the probe error path.
Move the init to the earliest available place in sun8i_dwmac_probe
(after stmmac_probe_config_dt, which initializes plat_dat), and the
deinit to the corresponding position in the cleanup order.
Since priv is not filled in until stmmac_dvr_probe, this requires
changing the sun8i_dwmac_set_syscon parameters to priv's two relevant
members.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Fixes: 634db83b82 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
sun8i_dwmac_exit calls sun8i_dwmac_unpower_internal_phy, but
sun8i_dwmac_init did not call sun8i_dwmac_power_internal_phy. This
caused PHY power to remain off after a suspend/resume cycle. Fix this by
recording if PHY power should be restored, and if so, restoring it.
Fixes: 634db83b82 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
While stmmac_pltfr_remove calls sun8i_dwmac_exit, the sun8i_dwmac_init
and sun8i_dwmac_exit functions are also called by the stmmac_platform
suspend/resume callbacks. They may be called many times during the
device's lifetime and should not release resources used by the driver.
Furthermore, there was no error handling in case registering the MDIO
mux failed during probe, and the EPHY clock was never released at all.
Fix all of these issues by moving the deinitialization code to a driver
removal callback. Also ensure the EPHY is powered down before removal.
Fixes: 634db83b82 ("net: stmmac: dwmac-sun8i: Handle integrated/external MDIOs")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_pltfr_remove does three things in one function, making it
inapproprate for unwinding the steps in the probe function. Currently,
a failure before the call to stmmac_dvr_probe would leak OF node
references due to missing a call to stmmac_remove_config_dt. And an
error in stmmac_dvr_probe would cause the driver to attempt to remove a
netdevice that was never added. Fix these by reordering the init and
splitting out the error handling steps.
Fixes: 9f93ac8d40 ("net-next: stmmac: Add dwmac-sun8i")
Fixes: 40a1dcee2d ("net: ethernet: dwmac-sun8i: Use the correct function in exit path")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN checks for NETREG_UNINITIALIZED to distinguish between
registration failure and unregistration in progress.
Since commit cb626bf566 ("net-sysfs: Fix reference count leak")
registration failure may, however, result in NETREG_UNREGISTERED
as well as NETREG_UNINITIALIZED.
This fix is similer to cebb69754f ("rtnetlink: Fix
memory(net_device) leak when ->newlink fails")
Fixes: cb626bf566 ("net-sysfs: Fix reference count leak")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From the existing definitions it's unclear which stat to
use to report filtering based on L2 dst addr in old
broadcast-medium Ethernet.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is a NCI command in work queue after closing the NCI device at
nci_unregister_device, The NCI command timer starts at flush_workqueue
function and then NCI command timeout handler would be called 5 second
after flushing the NCI command work queue and destroying the queue.
At that time, the timeout handler would try to use NCI command work queue
that is destroyed already. it will causes the problem. To avoid this
abnormal situation, change the sequence to prevent the NCI command timeout
handler from being called after destroying the NCI command work queue.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function sockfd_lookup uses fget on the value that is stored in
the file field of the returned structure, so fput should ultimately be
applied to this value. This can be done directly, but it seems better
to use the specific macro sockfd_put, which does the same thing.
Perform a source code refactoring by using the following semantic patch.
// <smpl>
@@
expression s;
@@
s = sockfd_lookup(...)
...
+ sockfd_put(s);
- fput(s->file);
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use kzalloc rather than kcalloc(1,...)
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
@@
- kcalloc(1,
+ kzalloc(
...)
// </smpl>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A call to dma_alloc_coherent() is wrapped by sonic_alloc_descriptors().
This is correctly freed in the remove function, but not in the error
handling path of the probe function. Fix this by adding the missing
dma_free_coherent() call.
While at it, rename a label in order to be slightly more informative.
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Chris Zankel <chris@zankel.net>
References: commit 10e3cc180e ("net/sonic: Fix a resource leak in an error handling path in 'jazz_sonic_probe()'")
Fixes: 74f2a5f0ef ("xtensa: Add support for the Sonic Ethernet device for the XT2000 board.")
Fixes: efcce83936 ("[PATCH] macsonic/jazzsonic network drivers update")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this, the driver runs into a link failure
arm-linux-gnueabi-ld: drivers/net/wan/slic_ds26522.o: in function `slic_ds26522_probe':
slic_ds26522.c:(.text+0x100c): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: slic_ds26522.c:(.text+0x1cdc): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: drivers/net/wan/slic_ds26522.o: in function `slic_write':
slic_ds26522.c:(.text+0x1e4c): undefined reference to `byte_rev_table'
Fixes: c37d4a0085 ("Maxim/driver: Add driver for maxim ds26522")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this, we run into a link error
arm-linux-gnueabi-ld: drivers/isdn/mISDN/dsp_audio.o: in function `dsp_audio_generate_law_tables':
(.text+0x30c): undefined reference to `byte_rev_table'
arm-linux-gnueabi-ld: drivers/isdn/mISDN/dsp_audio.o:(.text+0x5e4): more undefined references to `byte_rev_table' follow
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without crc32 support, this fails to link:
arm-linux-gnueabi-ld: net/wireless/scan.o: in function `cfg80211_scan_6ghz':
scan.c:(.text+0x928): undefined reference to `crc32_le'
Fixes: c8cb5b854b ("nl80211/cfg80211: support 6 GHz scanning")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without crc32, the driver fails to link:
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o: in function `wil_fw_verify':
fw.c:(.text+0x74c): undefined reference to `crc32_le'
arm-linux-gnueabi-ld: drivers/net/wireless/ath/wil6210/fw.o:fw.c:(.text+0x758): more undefined references to `crc32_le' follow
Fixes: 151a970650 ("wil6210: firmware download")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joakim Zhang