Chain swapping should only be enabled when the EEPROM chainmask is set to 5,
regardless of what the runtime chainmask is.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The kbuild test robot reports the following warning with x86_64-randconfig-x955:
warning: (RTL8192CE && RTL8192SE && RTL8192DE && RTL8723AE && RTL8192CU) selects
RTLWIFI which has unmet direct dependencies (NETDEVICES && WLAN &&
(RTL8192CE || RTL8192CU || RTL8192SE || RTL8192DE))
This warning was introduced in commit a290593, "rtlwifi: Modify files for addition
of rtl8723ae", and is d ue to a missing dependence of RTLWIFI on RTL8723AE.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: kbuild test robot <fengguang.wu@intel.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We do not correctly change interface type when switching from
IBSS mode to STA mode, that results in microcode errors.
Resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=886946
Reported-by: Jaroslav Skarvada <jskarvad@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be able to implement NS response offloading (in
regular operation or while in WoWLAN) drivers need
to know the IPv6 addresses assigned to interfaces.
Implement an IPv6 notifier in mac80211 to call the
driver when addresses change.
Unlike for IPv4, implement it as a callback rather
than as a list in the BSS configuration, that is
more flexible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A lot of the aggregation messages don't indicate the
station so they're hard to understand if there are
multiple sessions in progress. Make that easier by
adding the MAC address to most messages. Also add
the TID if it wasn't already there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Depending on the driver, having ARP filtering for
some addresses may be possible. Remove the logic
that tracks whether ARP filter is enabled or not
and give the driver the total number of addresses
instead of the length of the list so it can make
its own decision.
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are hardwares which support offload of data packets
for example when auto ARP is enabled the hw will send
the ARP response. In such cases if WEP encryption is
configured the hw must know the default WEP key in order
to encrypt the packets correctly.
When hw_accel is enabled and encryption type is set to WEP,
the driver should get the default key index from mac80211.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
[cleanups, fixes, documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There's a per-HCI device workqueue (hdev->workqueue) that should be used
for general per-HCI device work (except hdev->req_workqueue that's for
hci_request() related work). This patch fixes places using the
system-global work queue and makes them use the hdev->workqueue instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
This patch converts work assignment relying on hci_request() from the
system-global work queue to the per-HCI device specific work queue
(hdev->req_workqueue) intended for hci_request() related tasks.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The hci_request function is blocking and cannot be called through the
usual per-HCI device workqueue (hdev->workqueue). While hci_request is
in progress any other work from the queue, including sending HCI
commands to the controller would be blocked and eventually cause the
hci_request call to time out.
This patch adds a second workqueue to be used by operations needing
hci_request and thereby avoiding issues with blocking other workqueue
users.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Some new APIs will require tracing a chandef without
it being part of a channel context, so separate out
the tracing macros for that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To ease further DFS development regarding interface combinations, use
the interface combinations structure to test for radar capabilities.
Drivers can specify which channel widths they support, and in which
modes. Right now only a single AP interface is allowed, but as the
DFS code evolves other combinations can be enabled.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The NL80211_ATTR_USE_MFP attribute was originally added for
NL80211_CMD_ASSOCIATE, but it is actually as useful (if not even more
useful) with NL80211_CMD_CONNECT, so process that attribute with the
connect command, too.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Mesh PERR action frames are robust and thus may be encrypted, so add
proper head/tailroom to allow this. Fixes this warning when operating
a Mesh STA on ath5k:
WARNING: at net/mac80211/wpa.c:427 ccmp_encrypt_skb.isra.5+0x7b/0x1a0 [mac80211]()
Call Trace:
[<c011c5e7>] warn_slowpath_common+0x63/0x78
[<c011c60b>] warn_slowpath_null+0xf/0x13
[<e090621d>] ccmp_encrypt_skb.isra.5+0x7b/0x1a0 [mac80211]
[<e090685c>] ieee80211_crypto_ccmp_encrypt+0x1f/0x37 [mac80211]
[<e0917113>] invoke_tx_handlers+0xcad/0x10bd [mac80211]
[<e0917665>] ieee80211_tx+0x87/0xb3 [mac80211]
[<e0918932>] ieee80211_tx_pending+0xcc/0x170 [mac80211]
[<c0121c43>] tasklet_action+0x3e/0x65
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
A user reported warnings in ath5k due to transmitting frames with no
rates set up. The frames were Mesh PERR frames, and some debugging
showed an empty control block with just the vif pointer:
> [ 562.522682] XXX txinfo: 00000000: 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 ................
> [ 562.522688] XXX txinfo: 00000010: 00 00 00 00 00 00 00 00 54 b8 f2
> db 00 00 00 00 ........T.......
> [ 562.522693] XXX txinfo: 00000020: 00 00 00 00 00 00 00 00 00 00 00
> 00 00 00 00 00 ................
Set the IEEE80211_TX_INTFL_NEED_TXPROCESSING flag to ensure that
rate control gets run before the frame is sent.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As per email discussion Jouni Malinen pointed out that:
"P2P message exchanges can be executed on the current operating channel
of any operation (both P2P and non-P2P station). These can be on 5 GHz
and even on 60 GHz (so yes, you _can_ do GO Negotiation on 60 GHz).
As an example, it would be possible to receive a GO Negotiation Request
frame on a 5 GHz only radio and then to complete GO Negotiation on that
band. This can happen both when connected to a P2P group (through client
discoverability mechanism) and when connected to a legacy AP (assuming
the station receive Probe Request frame from full scan in the beginning
of P2P device discovery)."
This means that P2P messages can be sent over different radio devices.
However, these should use the same P2P device address so it should be
able to provision this from user-space. This patch adds a parameter for
this to struct vif_params which should only be used during creation of
the P2P device interface.
Cc: Jouni Malinen <j@w1.fi>
Cc: Greg Goldman <ggoldman@broadcom.com>
Cc: Jithu Jance <jithu@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[add error checking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the nl80211_mesh_power_mode enumeration which holds possible
values for the mesh power mode. These modes are unknown, active,
light sleep and deep sleep.
Add power_mode entry to the mesh config structure to hold the
user-configured default mesh power mode. This value will be used
for new peer links.
Add the dot11MeshAwakeWindowDuration value to the mesh config.
The awake window is a duration in TU describing how long the STA
will stay awake after transmitting its beacon in PS mode.
Add access routines to:
- get/set local link-specific power mode (STA)
- get remote STA's link-specific power mode (STA)
- get remote STA's non-peer power mode (STA)
- get/set default mesh power mode (mesh config)
- get/set mesh awake window duration (mesh config)
All config changes may be done at mesh runtime and take effect
immediately.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
[fix commit message line length, error handling in set station]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Move the default mesh beacon interval and DTIM period to cfg80211
and make them accessible to nl80211. This enables setting both
values when joining an MBSS.
Previously the DTIM parameter was not set by mac80211 so the
driver's default value was used.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This functions will be used for mesh beacons, too.
Signed-off-by: Marco Porsch <marco@cozybit.com>
[some formatting fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The established peer link count is indicated in mesh beacons and
used for other internal tasks. Previously it was not updated when
authenticated peering is performed in userspace.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Ranges are taken from IEEE 802.11-2012, common sense or current
implementation requirements.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Allow mesh interface to disable the power save which is by default
turn on in certain chipset. Testing with 2 units of ZCN-1523H-5-16
featuring AR9280 chipset which have power save enabled by default.
Constant reset if the average signal of the peer mesh STA is below
-80 dBm and power save is enabled.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When the driver's resume function can't completely
restore the configuration in the device, it returns
1 from the callback which will be treated like a HW
restart request, but done directly.
In this case, also call the driver's restart_complete()
function so it can finish the reconfiguration there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
My commit 529ba6e931
("mac80211: clean up association better in suspend")
introduced a bug when resuming from WoWLAN when a
device reset is desired. This case must not use the
suspend_bss_conf as it hasn't been stored.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When building the 80211 DocBook, scripts/kernel-doc reports
the following type of warnings:
Warning(include/net/cfg80211.h:334): No description found for return value of 'cfg80211_get_chandef_type'
These warnings are only reported when scripts/kernel-doc
runs in verbose mode.
To fix these use "Return:" to describe function return values.
Signed-off-by: Yacine Belkadi <yacine.belkadi.1@gmail.com>
[adjust for freq_reg_info() change]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Channel contexts are not always used with monitor interfaces. If no channel
context is set, use the oper channel, otherwise tx fails.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[check local->use_chanctx]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since:
commit b23b025fe2
Author: Ben Greear <greearb@candelatech.com>
Date: Fri Feb 4 11:54:17 2011 -0800
mac80211: Optimize scans on current operating channel.
we do not disable PS while going back to operational channel (on
ieee80211_scan_state_suspend) and deffer that until scan finish.
But since we are allowed to send frames, we can send a frame to AP
without PM bit set, so disable PS on AP side. Then when we switch
to off-channel (in ieee80211_scan_state_resume) we do not enable PS.
Hence we are off-channel with PS disabled, frames are not buffered
by AP.
To fix remove offchannel_ps_disable argument and always enable PS when
going off-channel and disable it when going on-channel, like it was
before.
Cc: stable@vger.kernel.org # 2.6.39+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During FT roaming, wpa_supplicant attempts to set the
key before association. This used to be rejected, but
as a side effect of my commit 66e67e4189
("mac80211: redesign auth/assoc") the key was accepted
causing hardware crypto to not be used for it as the
station isn't added to the driver yet.
It would be possible to accept the key and then add it
to the driver when the station has been added. However,
this may run into issues with drivers using the state-
based station adding if they accept the key only after
association like it used to be.
For now, revert to the behaviour from before the auth
and assoc change.
Cc: stable@vger.kernel.org
Reported-by: Cédric Debarge <cedric.debarge@acksys.fr>
Tested-by: Cédric Debarge <cedric.debarge@acksys.fr>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Also when things go wrong (queues don't get emtpy), try to
get some data from the HW.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The rate scaling won't treat the information in a frame
with IEEE80211_TX_CTL_AMPDU set if IEEE80211_TX_STAT_AMPDU
is cleared. But all the frames coming from an AGG tx queue
have IEEE80211_TX_CTL_AMPDU set, and IEEE80211_TX_STAT_AMPDU
is set only if the frame was sent in an AMPDU.
This means that all the data in frames in AGG tx queues that
aren't sent as an AMPDU is thrown away.
This is even more harmful when in bad link conditions, the
frames are sent in an AMPDU and then finally sent as single
frame. So a lot of failures weren't reported and the rate
scaling got stuck in high rates leading to very poor
connectivity.
Fix that by clearing IEEE80211_TX_CTL_AMPDU when the frame
isn't part of an AMPDU.
This bug was introduced by
2eb81a40aa
iwlwifi: don't clear CTL_AMPDU on frame status
This fix basically reverts the aforementioned commit.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On resuming, the opmode may have to be able to talk
to the WoWLAN/D3 firmware in order to query it about
its status and wakeup reasons. To do that, the opmode
has to call the new d3_resume() transport API which
will set up the device for command communcation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Writing 130 dwords into the device one by one is
rather inefficient, every one needs to lock, grab
NIC access (a few register reads/writes) and then
write the address and data registers.
Use the new memory clearing function to make this
easier and faster.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Sending a NULL pointer to iwl_trans_write_mem allows now
to zero SRAM.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Enabling the RF-kill interrupt is sufficient for getting
RF-kill notifications, and no other interrupt is needed
as the device isn't functional when suspended and will be
restarted/reconfigured when mac80211 resumes it later.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The dma_addr_t type is a scalar value, so it should
just be assigned, not memset.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The sanity checks allow 1 and 2 byte reads/writes of the extended
PCI config space to proceed; however, the code only supports 4
byte reads/writes. This patch adds support for 1 and 2 byte
reads/writes of the extended PCI config space.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For PCI config space access offsets < 256 for device '0',
bcma_extpci_write_config performs an 'ioremap_nocache' on a 4 byte
section of the PCI config space (an area that has already
previously been mapped), and then subsequently unmaps that 4 byte
section. This can't be a good thing for future read access from
that now unmapped location. Modify the config space writes to use
the existing access functions (similar to how it is done for the reads).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Consistently jump to the 'out' label for error conditions (adds
missing check for 'func' validity in bcma_extpci_write_config).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'val' has already been read by the prior call to 'mips_busprobe32';
this 'readl' is unnecessary.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default irqflag assignment for the I2S core on some Broadcom
4716/4748 devices is invalid and needs to be corrected (from the
Broadcom SDK).
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It brings the following goodies:
- LLCP socket timestamping (To be used e.g with the recently released nfctool
application for a more efficient skb timestamping when sniffing).
- A pretty big pn533 rework from Waldemar, preparing the driver to support
more flavours of pn533 based devices.
- HCI changes from Eric in preparation for the microread driver support.
- Some LLCP memory leak fixes, cleanups and slight improvements.
- pn544 and nfcwilink move to the devm_kzalloc API.
- An initial Secure Element (SE) API.
- An nfc.h license change from the original author, allowing non GPL
application code to safely include it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=YeWq
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-3.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"This is the first NFC patchset targeted at the 3.9 merge window.
It brings the following goodies:
- LLCP socket timestamping (To be used e.g with the recently released nfctool
application for a more efficient skb timestamping when sniffing).
- A pretty big pn533 rework from Waldemar, preparing the driver to support
more flavours of pn533 based devices.
- HCI changes from Eric in preparation for the microread driver support.
- Some LLCP memory leak fixes, cleanups and slight improvements.
- pn544 and nfcwilink move to the devm_kzalloc API.
- An initial Secure Element (SE) API.
- An nfc.h license change from the original author, allowing non GPL
application code to safely include it."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes a reported CPU soft lockup where the tasklet tries to acquire the
lock and blocks while ath_prepare_reset (holding the lock) waits for it
to complete.
Cc: stable@vger.kernel.org
Reported-by: Robert Shade <robert.shade@gmail.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: fix rx flush handling" added a deadlock that happens
because ath_rx_tasklet is called in a section that has already taken the
rx buffer lock.
It seems that the only purpose of the rxbuflock was a band-aid fix to the
reset vs rx tasklet race, which has been properly fixed in the commit
"ath9k: add a better fix for the rx tasklet vs rx flush race".
Now that the fix is in, we can safely remove the lock to avoid such issues.
Cc: stable@vger.kernel.org
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Felix Fietkau