This patch continues the code move out of ice_main.c
The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_clear
ice_vsi_close
ice_vsi_free_arrays
ice_vsi_map_rings_to_vectors
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch continues the code move out of ice_main.c
The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_alloc_rings
ice_vsi_set_rss_params
ice_vsi_set_num_qs
ice_get_free_slot
ice_vsi_init
ice_vsi_clear_rings
ice_vsi_alloc_arrays
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch continues the code move out of ice_main.c
The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_delete
ice_free_res
ice_get_res
ice_is_reset_recovery_pending
ice_vsi_put_qs
ice_vsi_dis_irq
ice_vsi_free_irq
ice_vsi_free_rx_rings
ice_vsi_free_tx_rings
ice_msix_clean_rings
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch continues the code move out of ice_main.c
The following top level functions (and related dependency functions) were
moved to ice_lib.c:
ice_vsi_start_rx_rings
ice_vsi_stop_rx_rings
ice_vsi_stop_tx_rings
ice_vsi_cfg_rxqs
ice_vsi_cfg_txqs
ice_vsi_cfg_msix
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The functions that are used for PF VSI/netdev setup will also be used
for SR-IOV support. To allow reuse of these functions, move these
functions out of ice_main.c to ice_common.c/ice_lib.c
This move is done across multiple patches. Each patch moves a few
functions and may have minor adjustments. For example, a function that was
previously static in ice_main.c will be made non-static temporarily in
its new location to allow the driver to build cleanly. These adjustments
will be removed in subsequent patches where more code is moved out of
ice_main.c
In this particular patch, the following functions were moved out of
ice_main.c:
int ice_add_mac_to_list
ice_free_fltr_list
ice_stat_update40
ice_stat_update32
ice_update_eth_stats
ice_vsi_add_vlan
ice_vsi_kill_vlan
ice_vsi_manage_vlan_insertion
ice_vsi_manage_vlan_stripping
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
rx_mini_pending was set to an incorrect value. This was causing EINVAL to
always be returned to 'ethtool -G'. The driver does not support mini or
jumbo rings so the respective settings should be zero.
Also, change the valid range of the number of descriptors in the rings to
make the code simpler and easier for users to understand (this removes the
valid settings of 8 and 16). Add a system log message indicating when the
number is rounded-up from what the user specifies with the 'ethtool -G'
command (i.e. when it is not a multiple of 32), and update the log message
when a user-provided value is out of range to also indicate the stride.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch makes a couple of changes in the way the driver uses the
"get capabilities" command.
1. Get device capabilities in addition to function capabilities
2. Align to latest spec by using cap_count to determine size of the
buffer in case of length error.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Query the Tx scheduler tree node information from FW before adding it to
the driver's software database. This will keep the node information current
in driver.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Previously the comment stated that VSI lists should be used when a
second VSI becomes a subscriber to the "VLAN address". VSI lists
are always used for VLAN membership, so replace "VLAN address" with
"MAC address". Also note that VLAN(s) always use VSI list rules.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We have MAX_FW_API_VER_BRANCH, MAX_FW_API_VER_MAJOR, and
MAX_FW_API_VER_MINOR that we use in ice_controlq.h to test when a
firmware version is newer than expected. This is currently tested by
comparing each field separately. Thus, we compare the branch field
against the MAX_FW_API_VER_BRANCH, and so forth.
This means that currently, if we suppose that the max firmware version
is defined as 0.2.1, i.e.
Then firmware 0.1.3 will fail to load. This is because the minor version
3 is greater than the max minor version 1.
This is not intuitive, because of the notion that increasing the major
firmware version to 2 should mean any firmware version with a major
version is less than 2 should be considered older than 2...
In order to allow both 0.2.1 and 0.1.3 to load, you would have to define
the "max" firmware version as 0.2.3.. It is possible that such
a firmware version doesn't even exist yet!
Fix this by replacing the current logic with an updated check that
behaves as follows:
First, we check the major version. If it is greater than the expected
version, then we prevent driver load. Additionally, a warning message is
logged to indicate to the system administrator that they need to update
their driver. This is now the only case where the driver will refuse to
load.
Second, if the major version is less than the expected version, we log
an information message indicating the NVM should be updated.
Third, if the major version is exact, we'll then check the minor
version. If the minor version is more than two versions less than
expected, we log an information message indicating the NVM should be
updated. If it is more than two versions greater than the expected
version, we log an information message that the driver should be
updated.
To support this, the ice_aq_ver_check function needs its signature
updated to pass the HW structure. Since we now pass this structure,
there is no need to pass the firmware API versions separately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Update branding strings and remove device ids 0x1594 and 0x1595.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Direct assignment is preferred over a memcpy()
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When shutting down the controlqs, we check if they are initialized
before we shut them down and destroy the lock. This is important, as it
prevents attempts to access the lock of an already shutdown queue.
Unfortunately, we checked rq.head and sq.head as the value to determine
if the queue was initialized. This doesn't work, because head is not
reset when the queue is shutdown. In some flows, the adminq will have
already been shut down prior to calling ice_shutdown_all_ctrlqs. This
can result in a crash due to attempting to access the already destroyed
mutex.
Fix this by using rq.count and sq.count instead. Indeed, ice_shutdown_sq
and ice_shutdown_rq already indicate that this is the value we should be
using to determine of the queue was initialized.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The user's coal configuration will be lost after reset, so the tx_coal
and rx_coal fields are added to the struct hns_nic_priv to save the coal
configuration and used to restore the user's configuration after the reset
is complete.
Fixes: bb6b94a896 ("net: hns3: Add reset interface implementation in client")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current hns3_get_max_available_channels returns the total number
of queues for the device, which makes ethtool -L set the number of queues
per channel queues incorrectly, so hns3_get_max_available_channels should
return the maximum available number of queues per channel, depending on
the total number of queues allocated and the hardware configurations.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
hclge_tm_schd_info_update should return an error when num_tc is greater
than alloc_tqps.
This patch changes the return type of hnae3_register_ae_algo from void
to int.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently hns3_nic_change_mtu will try to down the netdev before
setting mtu, and it does not up the netdev when the setting fails,
which causes netdev not up problem.
This patch fixes it by not returning when the setting fails.
Fixes: a8e8b7ff35 ("net: hns3: Add support to change MTU in HNS3 hardware")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware expects a unit of 128 bytes when setting
packet buffer. When calculating the packet buffer size,
hclge_rx_buffer_calc does not round up the size as a unit
of 128 byte, which may casue packet lost problem when stress
testing.
This patch fixes it by rounding up packet size when calculating.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds serdes parallel inner loopback support for self test.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In fact, our implementation of mac loopback is the implementation of app
loopback now. Current name is wrong. This patch renames mac loopback to
app loopback.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our loop mode includes mac loop, serdes loop and phy loop. Not all of them
are related with mac. This patch corrects their names.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The extra mac address of pause param is used to do double check
for pause frame. This patch set it to HW. If we do not do that,
pfc pause frame will be transferred protocol stack when normal
flow control mode is enabled.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for sctp checksum offload.
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When B53_SERDES is a loadable module, a built-in srab driver still
cannot reach it, so the previous fix is incomplete:
b53_srab.c:(.text+0x3f4): undefined reference to `b53_serdes_init'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe64): undefined reference to `b53_serdes_link_state'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe74): undefined reference to `b53_serdes_link_set'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe88): undefined reference to `b53_serdes_an_restart'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea0): undefined reference to `b53_serdes_phylink_validate'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea4): undefined reference to `b53_serdes_config'
Add a Kconfig dependency that forces srab to also be a module
in this case, but allow it to be built-in when serdes is
disabled or built-in.
Fixes: 7a8c7f5c30 ("net: dsa: b53: Fix build with B53_SRAB enabled and not B53_SERDES")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The newly added runtime-pm support causes a harmless warning
when CONFIG_PM is disabled:
drivers/net/phy/mdio-bcm-unimac.c:330:12: error: 'unimac_mdio_resume' defined but not used [-Werror=unused-function]
static int unimac_mdio_resume(struct device *d)
drivers/net/phy/mdio-bcm-unimac.c:321:12: error: 'unimac_mdio_suspend' defined but not used [-Werror=unused-function]
static int unimac_mdio_suspend(struct device *d)
Marking the functions as __maybe_unused is the easiest workaround
and avoids adding #ifdef checks.
Fixes: b78ac6ecd1 ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc points out that the length of the temporary buffer may not be sufficient for
large numbers of leds:
drivers/net/phy/mscc.c: In function 'vsc85xx_probe':
drivers/net/phy/mscc.c:460:45: error: '-mode' directive writing 5 bytes into a region of size between 0 and 9 [-Werror=format-overflow=]
ret = sprintf(led_dt_prop, "vsc8531,led-%d-mode", i);
^~~~~
drivers/net/phy/mscc.c:460:9: note: 'sprintf' output between 19 and 28 bytes into a destination of size 22
ret = sprintf(led_dt_prop, "vsc8531,led-%d-mode", i);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
While we can make a reasonable assumption that the number of LEDs is small,
the cost of making the buffer a little bigger is insignificant as well.
Fixes: 11bfdabb7f ("net: phy: mscc: factorize code for LEDs mode")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch that removed the only users of the oldadv/newadv variables
accidentally left the now-unused declarations behind:
drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c: In function 'dpaa_set_pauseparam':
drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c:185:14: error: unused variable 'oldadv' [-Werror=unused-variable]
drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c:185:6: error: unused variable 'newadv' [-Werror=unused-variable]
Fixes: 70814e819c ("net: ethernet: Add helper for set_pauseparam for Asym Pause")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:873:5: warning:
symbol 'aq_fw1x_set_power' was not declared. Should it be static?
Fixes: a0da96c08c ("net: aquantia: implement WOL support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qlogic/qed/qed_ooo.c: In function 'qed_ooo_delete_isles':
drivers/net/ethernet/qlogic/qed/qed_ooo.c:354:30: warning:
variable 'p_archipelago' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qed/qed_ooo.c: In function 'qed_ooo_join_isles':
drivers/net/ethernet/qlogic/qed/qed_ooo.c:463:30: warning:
variable 'p_archipelago' set but not used [-Wunused-but-set-variable]
Since commit 1eec2437d1 ("qed: Make OOO archipelagos into an array"),
'p_archipelago' is no longer in use.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta controller can handle speeds up to 2500Mbps on the SGMII
interface. This relies on serdes configuration, the lane must be
configured at 3.125Gbps and we can't use in-band autoneg at that speed.
The main issue when supporting that speed on this particular controller
is that the link partner can send ethernet frames with a shortened
preamble, which if not explicitly enabled in the controller will cause
unexpected behaviours.
This was tested on Armada 385, with the comphy configuration done in
bootloader.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trival cleanup, list_move_tail will implement the same function that
list_del() + list_add_tail() will do. hence just replace them.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trival cleanup, list_move_tail will implement the same function that
list_del() + list_add_tail() will do. hence just replace them.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Local variable 'autoneg' doesn't even exist:
drivers/net/phy/marvell.c: In function 'm88e1121_config_aneg':
drivers/net/phy/marvell.c:468:25: error: 'autoneg' undeclared (first use in this function); did you mean 'put_net'?
if (phydev->autoneg != autoneg || changed) {
^~~~~~~
Fixes: d6ab933647 ("net: phy: marvell: Avoid unnecessary soft reset")
Reported-by:Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses devm_ioremap_resource() which is only available when
CONFIG_HAS_IOMEM is set, make the driver depend on this config option.
User mode Linux does not have CONFIG_HAS_IOMEM set and the driver was
failing on this architecture.
Fixes: 14fceff477 ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BMCR.RESET bit on the Marvell PHYs has a special meaning in that
it commits the register writes into the HW for it to latch and be
configured appropriately. Doing software resets causes link drops, and
this is unnecessary disruption if nothing changed.
Determine from marvell_set_polarity()'s return code whether the register value
was changed and if it was, propagate that to the logic that hits the software
reset bit.
This avoids doing unnecessary soft reset if the PHY is configured in
the same state it was previously, this also eliminates the need for a
m88e1111_config_aneg() function since it now is the same as
marvell_config_aneg().
Tested-by: Wang, Dongsheng <dongsheng.wang@hxt-semitech.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While consolidating the PHY reset in phy_init_hw() an unconditionaly
BMCR soft-reset I became quite trigger happy with those. This was later
on deactivated for the Generic PHY driver on the premise that a prior
software entity (e.g: bootloader) might have applied workarounds in
commit 0878fff1f4 ("net: phy: Do not perform software reset for
Generic PHY").
Since we have a hook to wire-up a soft_reset callback, just use that and
get rid of the call to genphy_soft_reset() entirely. This speeds up
initialization and link establishment for most PHYs out there that do
not require a reset.
Fixes: 87aa9f9c61 ("net: phy: consolidate PHY reset in phy_init_hw()")
Tested-by: Wang, Dongsheng <dongsheng.wang@hxt-semitech.com>
Tested-by: Chris Healy <cphealy@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-09-25
This series contains updates to i40e and xsk.
Mariusz fixes an issue where the VF link state was not being updated
properly when the PF is down or up. Also cleaned up the promiscuous
configuration during a VF reset.
Patryk simplifies the code a bit to use the variables for PF and HW that
are declared, rather than using the VSI pointers. Cleaned up the
message length parameter to several virtchnl functions, since it was not
being used (or needed).
Harshitha fixes two potential race conditions when trying to change VF
settings by creating a helper function to validate that the VF is
enabled and that the VSI is set up.
Sergey corrects a double "link down" message by putting in a check for
whether or not the link is up or going down.
Björn addresses an AF_XDP zero-copy issue that buffers passed
from userspace to the kernel was leaked when the hardware descriptor
ring was torn down. A zero-copy capable driver picks buffers off the
fill ring and places them on the hardware receive ring to be completed at
a later point when DMA is complete. Similar on the transmit side; The
driver picks buffers off the transmit ring and places them on the
transmit hardware ring.
In the typical flow, the receive buffer will be placed onto an receive
ring (completed to the user), and the transmit buffer will be placed on
the completion ring to notify the user that the transfer is done.
However, if the driver needs to tear down the hardware rings for some
reason (interface goes down, reconfiguration and such), the userspace
buffers cannot be leaked. They have to be reused or completed back to
userspace.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When an AF_XDP UMEM is attached to any of the Rx rings, we disallow a
user to change the number of descriptors via e.g. "ethtool -G IFNAME".
Otherwise, the size of the stash/reuse queue can grow unbounded, which
would result in OOM or leaking userspace buffers.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Outstanding Rx descriptors are temporarily stored on a stash/reuse
queue. When/if the HW rings comes up again, entries from the stash are
used to re-populate the ring.
The latter required some restructuring of the allocation scheme for
the AF_XDP zero-copy implementation. There is now a fast, and a slow
allocation. The "fast allocation" is used from the fast-path and
obtains free buffers from the fill ring and the internal recycle
mechanism. The "slow allocation" is only used in ring setup, and
obtains buffers from the fill ring and the stash (if any).
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the zero-copy enabled XDP Tx ring is torn down, due to
configuration changes, outstanding frames on the hardware descriptor
ring are queued on the completion ring.
The completion ring has a back-pressure mechanism that will guarantee
that there is sufficient space on the ring.
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
msglen parameter seems to be unused in several virtchnl function.
This patch removes it from signatures of those functions.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When isup is false meaning that interface is going to shut down
set new speed to 0 to avoid double 'NIC Link is Down' messages.
Signed-off-by: Sergey Nemov <sergey.nemov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we are trying to change VF settings, it is possible for 2 race
conditions to happen. One, when the VF is created but not yet enabled.
Second, the VF is enabled but the VSI is still not created or not yet
re-created in the VF reset flow.
This patch introduces a helper function to validate that the VF is
enabled and that the VSI is set up. This patch also calls this
function from other functions which could get into these race conditions.
While we are poking around here, remove unnecessary parenthesis that
checkpatch was complaining about.
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In order to slightly simplify the code use the variables for pf and hw
that are declared in i40e_set_mac function.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up promiscuous configuration when a VF reset occurs.
Previously the promiscuous mode settings were still there after the VF
driver removal.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This resolves an issue where the VF link state was not being updated
when the PF is down or up, and the VF link state would always show
that it is running.
Signed-off-by: Mariusz Stachura <mariusz.stachura@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Version bump conflict in batman-adv, take what's in net-next.
iavf conflict, adjustment of netdev_ops in net-next conflicting
with poll controller method removal in net.
Signed-off-by: David S. Miller <davem@davemloft.net>
Anirudh Venkataramanan