Remove tclk from platform data. This makes the platform data
structure empty, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The t_clk is moved from the shared part of the ethernet driver into
the per port section. Each port can have its own gated clock, which it
needs to enable/disable, as oppossed to there being one clock shared
by all ports. In practice, only kirkwood supports this at the moment.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Remove now redundant tclk from SPI platform data. This makes the platform
data empty, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add tclk as a fixed rate clock for all platforms. In addition, on
kirkwood, add a gated clock for most of the clocks which can be gated.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
[mturquette@linaro.org: removed redundant CLKDEV_LOOKUP from Kconfig]
[mturquette@linaro.org: removed redundant clk.h from mach-dove/common.c]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Arnd Bergmann <arnd@arndb.de>
The patch "ARM: orion: Consolidate USB platform setup code.", commit
4fcd3f374a broke USB on TS-7800 and
other orion5x boards, because the wrong type of PHY was being passed
to the EHCI driver in the platform data. Orion5x needs EHCI_PHY_ORION
and all the others want EHCI_PHY_NA.
Allow the mach- code to tell the generic plat-orion code which USB PHY
enum to place into the platform data.
Version 2: Rebase to v3.3-rc2.
Reported-by: Ambroz Bizjak <ambrop7@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Ambroz Bizjak <ambrop7@gmail.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Patchset "ARM: orion: Refactor the MPP code common in the orion
platform" broke at least Orion5x based platforms. These platforms have
pins configured as GPIO when the selector is not 0x0. However the
common code assumes the selector is always 0x0 for a GPIO lines. It
then ignores the GPIO bits in the MPP definitions, resulting in that
Orion5x machines cannot correctly configure there GPIO lines.
The Fix removes the assumption that the selector is always 0x0.
In order that none GPIO configurations are correctly blocked,
Kirkwood and mv78xx0 MPP definitions are corrected to only set the
GPIO bits for GPIO configurations.
This third version, which does not contain any whitespace changes,
and is rebased on v3.3-rc2.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=N2B4
-----END PGP SIGNATURE-----
Merge tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
New feature development
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mfd/db8500-prcmu: remove support for early silicon revisions
ARM: ux500: fix the smp_twd clock calculation
ARM: ux500: remove support for early silicon revisions
ARM: ux500: update register files
ARM: ux500: register DB5500 PMU dynamically
ARM: ux500: update ASIC detection for U5500
ARM: ux500: support DB8520
ARM: picoxcell: implement watchdog restart
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: Orion: Remove address map info from all platform data structures
ARM: Orion: Get address map from plat-orion instead of via platform_data
ARM: Orion: mbus_dram_info consolidation
ARM: Orion: Consolidate the address map setup
ARM: Kirkwood: Add configuration for MPP12 as GPIO
ARM: Kirkwood: Recognize A1 revision of 6282 chip
ARM: ux500: update the MOP500 GPIO assignments
...
The former implementation adds a fix gpiochip label string
to the framework. This is confusing because orion_gpio_init
is called more than once and this ends up in different gpiochips
with the same label.
This patch adds the already present orion_gpio_chip_count to the
label string to make it unique in the system.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
sched_clock() is yet another blocker on the road to the single
image. This patch implements an idea by Russell King:
http://www.spinics.net/lists/linux-omap/msg49561.html
Instead of asking the platform to implement both sched_clock()
itself and the rollover callback, simply register a read()
function, and let the ARM code care about sched_clock() itself,
the conversion to ns and the rollover. sched_clock() uses
this read() function as an indirection to the platform code.
If the platform doesn't provide a read(), the code falls back
to the jiffy counter (just like the default sched_clock).
This allow some simplifications and possibly some footprint gain
when multiple platforms are compiled in. Among the drawbacks,
the removal of the *_fixed_sched_clock optimization which could
negatively impact some platforms (sa1100, tegra, versatile
and omap).
Tested on 11MPCore, OMAP4 and Tegra.
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Colin Cross <ccross@android.com>
Cc: Erik Gilling <konkers@android.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: STEricsson <STEricsson_nomadik_linux@list.st.com>
Cc: Lennert Buytenhek <kernel@wantstofly.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Krzysztof Halasa <khc@pm.waw.pl>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Use an getter function in plat-orion/addr-map.c to get the address map
structure, rather than pass it to drivers in the platform_data
structures. When the drivers are built for none orion platforms, a
dummy function is provided instead which returns NULL.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Move the *_mbus_dram_info structure into the orion platform and call it
orion_mbus_dram_info everywhere.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Compile tested on Dove, orion5x, mv78xx0. Boot tested on Kirkwood.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch adds missing include of linux/types.h to fix below build error.
CC arch/arm/mach-mv78xx0/mpp.o
In file included from arch/arm/mach-mv78xx0/include/mach/gpio.h:9,
from /home/axel/repos/git/linux-2.6/arch/arm/include/asm/gpio.h:5,
from include/linux/gpio.h:18,
from arch/arm/mach-mv78xx0/mpp.c:10:
arch/arm/plat-orion/include/plat/gpio.h:28: error: expected declaration specifiers or '...' before 'u32'
make[1]: *** [arch/arm/mach-mv78xx0/mpp.o] Error 1
make: *** [arch/arm/mach-mv78xx0] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than marking the mach/gpio.h header files which want to use the
trivial GPIOLIB implementation, mark those which do not want to use it
instead. This means that by default, you get the trivial implementation
and only have to do something extra if you need to. This should
encourage the use of the trivial default implementation.
As an additional bonus, several gpio.h header files become empty.
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many of the gpio_to_irq implementations use the gpiolib version of this
function. Provide the standard gpiolib gpio_to_irq() for everyone, but
allow platforms to override it if they wish. Add the neccessary
overrides for those platforms which do not use the standard definition.
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Consolidate 24 trivial gpiolib implementions out of mach/gpio.h
into asm/gpio.h. This is basically the include of asm-generic/gpio.h
and the definition of gpio_get_value, gpio_set_value, and gpio_cansleep
as described in Documentation/gpio.txt
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: David Brown <davidb@codeaurora.org>
Acked-by: David Brown <davidb@codeaurora.org>
Tested-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes a regression introduced by e59347a "arm: orion:
Use generic irq chip".
Depending on the device, interrupts acknowledgement is done by setting
or by clearing a dedicated register. Replace irq_gc_ack() with some
{set,clr}_bit variants allows to handle both cases.
Note that this patch affects the following SoCs: Davinci, Samsung and
Orion. Except for this last, the change is minor: irq_gc_ack() is just
renamed into irq_gc_ack_set_bit().
For the Orion SoCs, the edge GPIO interrupts support is currently
broken. irq_gc_ack() try to acknowledge a such interrupt by setting
the corresponding cause register bit. The Orion GPIO device expect the
opposite. To fix this issue, the irq_gc_ack_clr_bit() variant is used.
Tested on Network Space v2.
Reported-by: Joey Oravec <joravec@drewtech.com>
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
mv78xx0 and kirkwood use identical mpp code.
It should also be possible to rewrite the orion5x mpp to use this
platform code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This change removes the interrupt resource. The driver does not use
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
The core interrupt chip is a straight forward conversion. The gpio
chip is implemented with two instances of the irq_chip_type which can
be switched with the irq_set_type function. That allows us to use the
generic callbacks and avoids the conditionals in them.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Reorder
irq_set_chip()
irq_set_chip_data()
irq_set_handler()
to
irq_set_chip()
irq_set_handler()
irq_set_chip_data()
so the next patch can combine irq_set_chip() and irq_set_handler() to
irq_set_chip_and_handler().
Automated conversion with coccinelle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch makes the various mach dirs that use the plat-orion GPIO
code pass in GPIO-related platform info (GPIO controller base address,
secondary base IRQ number, etc) explicitly, instead of having
plat-orion get those values by including a mach dir include file --
the latter mechanism is problematic if you want to support multiple
ARM platforms in the same kernel image.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch makes the various mach dirs that use the plat-orion time
code pass in timer and bridge addresses explicitly, instead of having
plat-orion get those values by including a mach dir include file --
the latter mechanism is problematic if you want to support multiple
ARM platforms in the same kernel image.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Convert orion platforms to use the new sched_clock() infrastructure for
extending 32bit counters to full 64-bit nanoseconds.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
ftrace requires sched_clock() to be notrace. Ensure that all
implementations are so marked. Also make sure that they include
linux/sched.h
Also ensure OMAP clocksource read functions are marked notrace as
they're used for sched_clock() too.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Tested-by: Eric Miao <eric.y.miao@gmail.com>
Tested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In d7e81c2 (clocksource: Add clocksource_register_hz/khz interface) new
interfaces were added which simplify (and optimize) the selection of the
divisor shift/mult constants. Switch over to using this new interface.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 21f0ba90a4 "orion/kirkwood: reset PCIe unit on boot" made the
reset of the PCIe unit unconditional. While this may fix problems on some
targets, this also causes problems on other targets.
Saeed Bishara <saeed@marvell.com> said about the original problem: "We
couln't pinpoint the root cause of this issue, actually we failed to
reproduce that issue."
So let's restrict the reset of the PCIe unit only to the target where
the original problem was observed.
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits)
ALSA: hda - Add pin-fix for HP dc5750
ALSA: als4000: Fix potentially invalid DMA mode setup
ALSA: als4000: enable burst mode
ALSA: hda - Fix initial capsrc selection in patch_alc269()
ASoC: TWL4030: Capture route runtime DAPM ordering fix
ALSA: hda - Add PC-beep whitelist for an Intel board
ALSA: hda - More relax for pending period handling
ALSA: hda - Define AC_FMT_* constants
ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs
ALSA: hda - Add support for HDMI HBR passthrough
ALSA: hda - Set Stream Type in Stream Format according to AES0
ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed
ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF
ASoC: wm9081: fix resource reclaim in wm9081_register error path
ASoC: wm8978: fix a memory leak if a wm8978_register fail
ASoC: wm8974: fix a memory leak if another WM8974 is registered
ASoC: wm8961: fix resource reclaim in wm8961_register error path
ASoC: wm8955: fix resource reclaim in wm8955_register error path
ASoC: wm8940: fix a memory leak if wm8940_register return error
ASoC: wm8904: fix resource reclaim in wm8904_register error path
...
Patch found in QNAPs vendor source package, with some cleanups
(proper defines, shortened max. timeout from 1s to 200ms).
Without this patch the PCIe SATA controller (Marvell 88sx7042/sata_mv)
in my QNAP TS-419P (Marvell 88f6281/Kirkwood) stops working after a
few minutes.
The symptomes are described in this thread:
http://marc.info/?l=linux-ide&m=124822863706181&w=2
[ Note: this is a workaround in need of a better analysis/solution -- NP ]
Acked-by: Saeed Bishara <saeed@marvell.com>
Tested-by: Bernhard R. Link <brl@pcpool00.mathematik.uni-freiburg.de>
Seconded-by: Martin Michlmayr <tbm@cyrius.com>
I'm_not_very_happy_with_it-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch add audio related definitions and functions
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for a board to register a callback to get the state of the
RnB line if it has it attached.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The PCIe inbound window size is supposed to be a power of two. If
the total amount of RAM installed in the system is not a power of two,
round it up such that it is.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Include linux/init.h for __init to fix this error:
CC [M] drivers/net/wireless/wl12xx/boot.o
In file included from arch/arm/mach-kirkwood/include/mach/gpio.h:13,
from arch/arm/include/asm/gpio.h:5,
from include/linux/gpio.h:7,
from drivers/net/wireless/wl12xx/boot.c:24:
arch/arm/plat-orion/include/plat/gpio.h:32: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘orion_gpio_init’
make[6]: *** [drivers/net/wireless/wl12xx/boot.o] Error 1
make[5]: *** [drivers/net/wireless/wl12xx] Error 2
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The Orion watchdog driver is also used on Kirkwood.
Convention is to use orion5x for stuff specific to 88F5xxx Orion chips
and simply "orion" for shared stuff across SoCs including Kirkwood.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
With a TCLK = 200MHz, the half period of the hardware timer is roughly
10 seconds. Because cnt32_to_63() must be called at least once per
half period of the base hardware counter, it is a bit risky to rely
solely on scheduling to generate frequent enough calls. Let's use a
kernel timer to ensure this.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
sched_clock implementation for orion platform. Its realized using
free-running clocksource timer, which provides a resolution of 7.5ns
(depending on tclk). It's derived from PXA's sched_clock implementation.
[ nico: renamed orion2ns to tclk2ns, fixed max value in the comment ]
Signed-off-by: Stefan Agner <stefan.agner@yahoo.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Symbols like SOFT_RESET are way too generic to be exported at large.
To avoid this, let's move the mbus bridge register defines into a
separate file and include it where needed. This affects mach-kirkwood,
mach-loki, mach-mv78xx0 and mach-orion5x simultaneously as they all
share code in plat-orion which relies on those defines.
Some other defines have been moved to narrower scopes, or simply deleted
when they had no user.
This fixes compilation problem with mpt2sas on the above listed
platforms.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The orion5x-wdt driver is now registered as a platform device and
receives the tclk value as platform data. This fixes a compile issue
cause by a previously removed define "ORION5X_TCLK".
Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Kristof Provost <kristof@sigsegv.be>
Cc: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Martin Michlmayr <tbm@cyrius.com>
Cc: Sylver Bruneau <sylver.bruneau@googlemail.com>
Cc: Kunihiko IMAI <bak@d2.dion.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Especially on Kirkwood, a couple GPIOs are actually only output capable.
Let's separate the ability to configure a GPIO as input or output to
accommodate this restriction.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
The GPIO interrupts can be configured as either level triggered or edge
triggered, with a default of level triggered. When an edge triggered
interrupt is requested, the gpio_irq_set_type method is called which
currently switches the given IRQ descriptor between two struct irq_chip
instances: orion_gpio_irq_level_chip and orion_gpio_irq_edge_chip. This
happens via __setup_irq() which also calls irq_chip_set_defaults() to
assign default methods to uninitialized ones. The problem is that
irq_chip_set_defaults() is called before the irq_chip reference is
switched, leaving the new irq_chip (orion_gpio_irq_edge_chip in this
case) with uninitialized methods such as chip->startup() causing a kernel
oops.
Many solutions are possible, such as making irq_chip_set_defaults() global
and calling it from gpio_irq_set_type(), or calling __irq_set_trigger()
before irq_chip_set_defaults() in __setup_irq(). But those require
modifications to the generic IRQ code which might have adverse effect on
other architectures, and that would still be a fragile arrangement.
Manually copying the missing methods from within gpio_irq_set_type()
would be really ugly and it would break again the day new methods with
automatic defaults are added.
A better solution is to have a single irq_chip instance which can deal
with both edge and level triggered interrupts. It is also a good idea
to switch the IRQ handler instead, as the edge IRQ handler allows for
one edge IRQ event to be queued as the IRQ is actually masked only when
that second IRQ is received, at which point the hardware can queue an
additional IRQ event, making edge triggered interrupts a bit more
reliable.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
Split off Orion GPIO handling code into plat-orion/, and add
support for multiple sets of (32) GPIO pins.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
The Orion ehci driver serves the Orion, kirkwood and DD Soc families.
Since each of those integrate a different USB phy we should have the
ability to use few initialization sequences or to leave the boot loader
phy settings as is.
Signed-off-by: Ronen Shitrit <rshitrit@marvell.com>
This patch performs the equivalent include directory shuffle for
plat-orion, and fixes up all users.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
The Discovery Duo (MV78xx0) has two x4 PCIe ports which can either
be used in x4 mode or in quad x1 mode. This patch adds an accessor
function to the generic plat-orion PCIe handling code to detect in
which of the two modes we're running (which is determined by strap
pins and/or configured by the bootloader).
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Some Feroceon-based SoCs have an MBUS bridge interrupt controller
that requires writing a one instead of a zero to clear edge
interrupt sources such as timer expiry.
This patch adds a new BRIDGE_INT_TIMER1_CLR define, which platform
code can set to either ~BRIDGE_INT_TIMER1 (write-zero-to-clear) or
BRIDGE_INT_TIMER1 (write-one-to-clear) depending on the platform.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Make it clear that Orion top-level IRQs are level-triggered. This
means that we don't need an ->ack() handler, or at least, we don't
need the ->ack() handler (or the acking part of the ->mask_ack()
handler) to actually do anything.
Given that, we might as well point our ->mask_ack() handler at the
->mask() handler instead of providing a dummy ->ack() handler, since
providing a ->mask_ack() handler on level IRQ sources will prevent
->ack() from ever being called.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Split off Orion time handling code into plat-orion/.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Split off Orion PCIe handling code into plat-orion/.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Split off Orion IRQ handling code into plat-orion/, and add
support for multiple sets of (32) interrupts.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Create arch/arm/plat-orion/, for peripherals shared between various
Marvell Orion SoCs.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Reviewed-by: Tzachi Perelstein <tzachi@marvell.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Andrew Lunn