This structure is only used to copy into another structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
15136 5112 0 20248 4f18 drivers/pinctrl/qcom/pinctrl-ssbi-mpp.o
after:
bss dec hex filename
14849 5024 0 19873 4da1 drivers/pinctrl/qcom/pinctrl-ssbi-mpp.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
18958 9000 128 28086 6db6 drivers/pinctrl/bcm/pinctrl-bcm2835.o
after:
text data bss dec hex filename
18764 8912 128 27804 6c9c drivers/pinctrl/bcm/pinctrl-bcm2835.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the below warning
--> Prefer 'unsigned int' to bare use of 'unsigned'.
--> line over 80 characters.
--> Prefer 'unsigned int **' to bare use of 'unsigned **'.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch fixes the kernel doc warnings in the driver.
Signed-off-by: Nava kishore Manne <navam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
21671 3632 128 25431 6357 drivers/pinctrl/pinctrl-st.o
after:
text data bss dec hex filename
21366 3576 128 25070 61ee drivers/pinctrl/pinctrl-st.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Acked-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
WARN_ON causes a backtrace to get logged which is only useful for
kernel bugs. For signalling a firmware bug dev_warn(dev, FW_BUG "...")
should be used.
This fixes users running userspace software to monitor kernel oopses
getting a false positive bug-report every boot because of the wrong
use of WARN_ON.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Various IMX platforms may have different imx_pmx_ops.gpio_set_direction
implementations, so let's make it platform specific callbacks instead of
the fixed common one.
Currently only VF610 platform implements it. No function level changes.
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
gpio_request_enable/disable_free actually are not quite necessary as
standard IMX pinctrl binding already sets GPIO mux from device tree,
e.g. VF610_PAD_PTB20__GPIO_42 or MX7D_PAD_SD2_CD_B__GPIO5_IO9
No need to do it again in gpio_request_enable.
And according to Stefan:
"For all GPIO I checked in upstream device trees we assign a pinctrl
to the same node, so in all cases gpio_request_enable/disable is really
unnecessary."
So it should be safe to simply remove it.
Note that this changes semantics for Vybrid, e.g.
"The two functions have been introduced for Vybrid (through
SHARE_MUX_CONF_REG) and mux pins as GPIOs automatically when a GPIO
gets requested. The automatic mux is optional by the pinmux/gpio
subsystem semantics, and other NXP devices do not use it, instead an
explicit pinctrl node is added in the device tree to mux GPIOs where
required. Hence this change aligns Vybrid to other NXP (i.MX) devices.
Note that all upstream device tree assign proper pinctrl properties
where GPIOs are used so no change is necessary for device trees."
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
i.MX 7ULP has three IOMUXC instances: IOMUXC0 for M4 ports,
IOMUXC1 for A7 ports and IOMUXC DDR for DDR interface.
This patch adds the IOMUXC1 support for A7.
It only supports generic pin config.
Cc: Bai Ping <ping.bai@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The generic pinmux property seems to be more suitable for IMX.
So we change to use 'pinmux' instead of 'pins'.
Cc: Bai Ping <ping.bai@nxp.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Save registers lost in the sleep when suspending, and restore them
when resuming.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For LD11/20 SoCs (capable of per-pin input enable), the iectrl bit
number matches its pin number. So, this is redundant information.
Instead, we just need a flag to know if the iectrl gating exists or not.
With this refactoring, 5 bits in pin data will be saved.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are a bunch of GPIO muxing data, but most of them are actually
unneeded because GPIO-to-pin mapping can be specified by "gpio-ranges"
DT properties.
Tables that contain a set of GPIO pins are still needed for the named
mapping by "gpio-ranges-group-names". This is a much cleaner way for
UniPhier SoC family where GPIO numbers are not straight mapped to pin
numbers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For LD11/LD20 SoCs (capable of per-pin input enable), iectrl bits are
located across multiple registers. So, the register offset must be
taken into account. Otherwise, wrong input-enable status is displayed.
While we here, rename the macro because it is a base address.
Fixes: aa543888ca ("pinctrl: uniphier: support per-pin input enable for new SoCs")
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
All UniPhier pinctrl drivers are built-in. Exporting the symbol
is meaningless.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
13129 2808 192 16129 3f01 drivers/pinctrl/qcom/pinctrl-msm.o
after:
text data bss dec hex filename
12839 2720 192 15751 3d87 drivers/pinctrl/qcom/pinctrl-msm.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
17061 6992 0 24053 5df5 drivers/pinctrl/qcom/pinctrl-ssbi-gpio.o
after:
text data bss dec hex filename
16777 6904 0 23681 5c81 drivers/pinctrl/qcom/pinctrl-ssbi-gpio.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into another structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
12775 3696 64 16535 4097 drivers/pinctrl/pinctrl-coh901.o
after:
bss dec hex filename
12440 3640 64 16144 3f10 drivers/pinctrl/pinctrl-coh901.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into another structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
17545 5376 0 22921 5989 drivers/pinctrl/nomadik/pinctrl-abx500.o
after:
bss dec hex filename
17273 5320 0 22593 5841 drivers/pinctrl/nomadik/pinctrl-abx500.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
7754 2328 0 10082 2762 drivers/pinctrl/vt8500/pinctrl-wmt.o
after:
text data bss dec hex filename
7472 2272 0 9744 2610 drivers/pinctrl/vt8500/pinctrl-wmt.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This structure is only used to copy into other structure, so declare
it as const.
This issue was detected using Coccinelle and the following semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct gpio_chip i@p = { ... };
@ok@
identifier r.i;
expression e;
position p;
@@
e = i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
struct gpio_chip e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct gpio_chip i = { ... };
In the following log you can see a significant difference in the code size
and data segment, hence in the dec segment. This log is the output
of the size command, before and after the code change:
before:
text data bss dec hex filename
11866 3520 128 15514 3c9a drivers/pinctrl/pinctrl-rza1.o
after:
text data bss dec hex filename
11539 3464 128 15131 3b1b drivers/pinctrl/pinctrl-rza1.o
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The I2C pin functions in R_PIO used to be named "s_twi".
As we usually use the name "i2c" instead of "twi" in the mainline
kernel, change these names to "s_i2c" for consistency.
The "s_twi" functions are not yet referenced by any device trees in
mainline kernel so I think it's safe to change the name.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
R40 is said to be an upgrade of A20, and its pin configuration is also
similar to A20 (and thus similar to A10).
Add support for R40 to the A10 pinctrl driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIO_PULL bits configurations in TLMM_GPIO_CFG register
differs for IPQ40xx from rest of the other qcom SoCs.
As it does not support the keeper state and therefore can't
support bias-bus-hold property.
This patch adds a pull_no_keeper setting which configures the
msm_gpio_pull bits for ipq40xx. This is required to fix the
proper configurations of gpio-pull bits for nand pins mux.
IPQ40xx SoC:
2'b10: Internal pull up enable.
2'b11: Unsupport
For other SoC's:
2'b10: Keeper
2'b11: Pull-Up
Note: Due to pull_no_keeper length, all kerneldoc entries
in the msm_pinctrl_soc_data struct had to be realigned.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds multiple pinctrl functions and mappings
for SDIO, NAND, I2S, WIFI, PCIE, LEDs, etc... that have
been missing from the current minimal version.
This patch has been updated from the original version
that was posted by Ram Chandra Jangir on the LEDE-DEV ML:
<https://patchwork.ozlabs.org/patch/752962/>. A short
summary of the changes are documented in the device-tree
patch of this series:
"dt-bindings: pinctrl: add most other IPQ4019 pin functions and groups"
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Fix the documentation build as the docs were moved.
- Correct the UART pin list on the Intell Merrifield.
- Fix pin assignment and number of pins on the Marvell Armada
37xx pin controller.
- Cover the Setzer models in the Chromebook DMI quirk in the
Intel cheryview driver so they start working.
- Add the missing "sim" function to the sunxi driver.
- Fix USB pin definitions on Uniphier Pro4.
- Smatch fix for invalid reference in the zx pin control driver.
-----BEGIN PGP SIGNATURE-----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=Dyh5
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
"These are the pin control fixes I have gathered since the return from
my vacation. They boiled in -next a while so let's get them in.
Apart from the documentation build it is purely driver fixes. Which is
nice. The Intel fixes seem kind of important.
- Fix the documentation build as the docs were moved
- Correct the UART pin list on the Intel Merrifield
- Fix pin assignment and number of pins on the Marvell Armada 37xx
pin controller
- Cover the Setzer models in the Chromebook DMI quirk in the Intel
cheryview driver so they start working
- Add the missing "sim" function to the sunxi driver
- Fix USB pin definitions on Uniphier Pro4
- Smatch fix for invalid reference in the zx pin control driver"
* tag 'pinctrl-v4.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: generic: update references to Documentation/pinctrl.txt
pinctrl: intel: merrifield: Correct UART pin lists
pinctrl: armada-37xx: Fix number of pin in south bridge
pinctrl: armada-37xx: Fix the pin 23 on south bridge
pinctrl: cherryview: Add Setzer models to the Chromebook DMI quirk
pinctrl: sunxi: add a missing function of A10/A20 pinctrl driver
pinctrl: uniphier: fix USB3 pin assignment for Pro4
pinctrl: zte: fix dereference of 'data' in zx_set_mux()
Pin 23 on South bridge does not belong to the rgmii group. It belongs to
a separate group which can have 3 functions.
Due to this the fix also have to update the way the functions are
managed. Until now each groups used NB_FUNCS(which was 2) functions. For
the mpp23, 3 functions are available but it is the only group which needs
it, so on the loop involving NB_FUNCS an extra test was added to handle
only the functions added.
The bug was visible with the merge of the commit 07d065abf9 "arm64:
dts: marvell: armada-3720-db: Add vqmmc regulator for SD slot", the gpio
regulator used the gpio 23, due to this the whole rgmii group was setup
to gpio which broke the Ethernet support on the Armada 3720 DB
board. Thanks to this patch, the UHS SD cards (which need the vqmmc)
_and_ the Ethernet work again.
Cc: stable@vger.kernel.org
Fixes: 87466ccd94 ("pinctrl: armada-37xx: Add pin controller support
for Armada 37xx")
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add one more model to the Chromebook DMI quirk to make it working again.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Fixes: 2a8209fa68 ("pinctrl: cherryview: Extend the Chromebook DMI quirk to Intel_Strago systems")
Reported-by: mail@abhishek.geek.nz
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Drivers that need IRQ_DOMAIN_HIERARCHY should "select" it, but
drivers/pinctrl/stm32/Kconfig is the only exception that uses
"depends on" syntax. This prevents GPIO drivers from select'ing
IRQ_DOMAIN_HIERARCHY.
For example, if I add "select IRQ_DOMAIN_HIERARCHY" to GPIO_XGENE_SB,
I get the following recursive dependency error.
drivers/gpio/Kconfig:13:error: recursive dependency detected!
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpio/Kconfig:13: symbol GPIOLIB is selected by PINCTRL_STM32
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/pinctrl/stm32/Kconfig:3: symbol PINCTRL_STM32 is selected by PINCTRL_STM32F429
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/pinctrl/stm32/Kconfig:11: symbol PINCTRL_STM32F429 depends on IRQ_DOMAIN_HIERARCHY
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
kernel/irq/Kconfig:67: symbol IRQ_DOMAIN_HIERARCHY is selected by GPIO_XGENE_SB
For a resolution refer to Documentation/kbuild/kconfig-language.txt
subsection "Kconfig recursive dependency limitations"
drivers/gpio/Kconfig:502: symbol GPIO_XGENE_SB depends on GPIOLIB
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The PH16 pin has a function with mux id 0x5, which is the DET pin of the
"sim" (smart card reader) IP block.
This function is missing in old versions of A10/A20 SoCs' datasheets and
user manuals, so it's also missing in the old drivers. The newest A10
Datasheet V1.70 and A20 Datasheet V1.41 contain this pin function, and
it's discovered during implementing R40 pinctrl driver.
Add it to the driver. As we now merged A20 pinctrl driver to the A10
one, we need to only fix the A10 driver now.
Fixes: f2821b1ca3 ("pinctrl: sunxi: Move Allwinner A10 pinctrl
driver to a driver of its own")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
According to pinctrl assignment for Pro4, each definition of USB#2 and
USB#3 are as follows.
184: USB2VBUS
185: USB2OD
186: USB2ID
187: USB3VBUS
188: USB3OD
USB#2 has an additional pin "USB2ID", but the chip doesn't use this pin
while in host-mode. Considering this pin, the pin definitions for USB#3
should be {187, 188}.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Two local variables (shift and reg_con) were initialized to unused
values - they were overwritten just few lines after. Getting rid of
this unused initialization allows dropping other variables and
compacting slightly the code.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Unlike for other countable members, the driver used u32 for number of
banks (nr_banks). There is no specific need for using fixed-width
integer in this particular place. Make it consistent.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Number of IO memory resources cannot be negative obviously and the
driver depends silently on this (by iterating from 0 to
nr_ext_resources+1). Make this requirement explicit.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
We already have macros for values used by driver and Device Tree
sources for pin mux configuration. Use them instead of duplicating
defines.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
When setting the pin function for external interrupts, the driver used
wrong IO memory address base. The pin function register is always under
pctl_base, not the eint_base.
By updating wrong register, the external interrupts for chosen GPIO
would not work at all and some other GPIO might be configured to wrong
value. For example on Exynos5433-based boards, the external interrupts
for gpf{1-5}-X GPIOs should not work at all (driver toggled reserved
registers from ALIVE bank instead).
Platforms other than Exynos5433 should not be affected as eint_base
equals pctl_base in such case.
Fixes: 8b1bd11c1f ("pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank")
Cc: <stable@vger.kernel.org>
Reported-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
After commit 8b1bd11c1f ("pinctrl: samsung: Add the support the
multiple IORESOURCE_MEM for one pin-bank"), the S3C24xx (and probably
S3C64xx as well) fails:
Unable to handle kernel NULL pointer dereference at virtual address 000000a8
...
(s3c24xx_demux_eint4_7) from [<c004469c>] (__handle_domain_irq+0x6c/0xcc)
(__handle_domain_irq) from [<c0009444>] (s3c24xx_handle_irq+0x6c/0x12c)
(s3c24xx_handle_irq) from [<c000e5fc>] (__irq_svc+0x5c/0x78)
Mentioned commit moved the pointer to controller's base IO memory address
from each controller's driver data (samsung_pinctrl_drv_data) to per-bank
structure (samsung_pin_bank). The external interrupt demux
handlers (s3c24xx_demux_eint()) tried to get this base address from opaque
pointer stored under irq_chip data:
struct irq_data *irqd = irq_desc_get_irq_data(desc);
struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
...
pend = readl(bank->eint_base + EINTPEND_REG);
which is wrong because this is hardware irq and it bank was never set
for this irq_chip.
For S3C24xx and S3C64xx, this partially reverts mentioned commit by
bringing back the virt_base stored under each controller's driver data
(samsung_pinctrl_drv_data). This virt_base address will be now
duplicated:
- samsung_pinctrl_drv_data->virt_base: used on S3C24xx and S3C64xx,
- samsung_pin_bank->pctl_base: used on Exynos.
Fixes: 8b1bd11c1f ("pinctrl: samsung: Add the support the multiple IORESOURCE_MEM for one pin-bank")
Cc: <stable@vger.kernel.org>
Cc: Sergio Prado <sergio.prado@e-labworks.com>
Reported-by: Sergio Prado <sergio.prado@e-labworks.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Lihua Yao <ylhuajnu@163.com>
This patch renames the pin function macro definitions of the GPSR1 and
IPSR4 registers value for the CS1# pin.
This is a correction because GPSR and IPSR register specification for
R8A7796 SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.54E.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes IPSR{12,17,18} and MOD_SEL0 pin assignment for FSO pins
group.
This is a correction because GPSR and IPSR register specification for
R8A7796 SoC was changed in R-Car Gen3 Hardware User's Manual Rev.0.54E.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the macro definitions of SATA_DEVSLP_B pins function
deleted.
This is a correction to the incorrect implementation of IPSR register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the macro definitions of FSCLKST pins function and IPSR7
bit[15:12] register deleted.
This is a correction because IPSR register specification for R8A7796 SoC
was changed in R-Car Gen3 Hardware User's Manual Rev.0.53E or later.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes to set MOD_SEL2 bit19 when using TCLK2_A pin function is
selected for IPSR16 bit[23:20] or using TCLK2_B pin function is selected
for IPSR17 bit[27:24].
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the implementation incorrect of IPSR register value
definitions for NFDATA{0..13} and NF{ALE,CLE,WE_N,RE_N} pins function.
This is a correction to the incorrect implementation of IPSR register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the implementation incorrect of IPSR register value
definitions for FMCLK{_C,_D} and FMIN{_C,_D} pins function.
This is a correction to the incorrect implementation of IPSR register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes SCIF_CLK_{A,B} pin's MOD_SEL assignment from MOD_SEL1
bit11 to MOD_SEL1 bit10.
This is a correction to the incorrect implementation of IPSR register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the implementation incorrect of MOD_SEL2 bit26 value
when SCK5_A pin function is selected for IPSR16 bit[31:28].
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the implementation incorrect of MOD_SEL1 bit[25:24]
value when STP_ISEN_1_D pin function is selected for IPSR17 bit[27:24].
This is a correction to the incorrect implementation of MOD_SEL register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Pins D6 and D7 of the MMC interface can be muxed to two different sets
of pins, but currently only one set is supported.
Add a pin group for the alternative set to fix this.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Tested-by: Chris Paterson <chris.paterson2@renesas.com>
Fix a copy-and-paste bug in the MSIOF3 SS2_E mux array.
Fixes: 4753231cc9 ("pinctrl: sh-pfc: r8a7796: Add MSIOF pins, groups and functions")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the IPSR register setting when the MSIOF3_SS1_E pin
function is selected.
This is a correction to the incorrect implementation of IPSR register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the incorrect IPSR register value definitions for
MSIOF3_{SS1,SS2}_E pin functions.
This is a correction to the incorrect implementation of IPSR register
pin assignment for R8A7796 SoC specification of R-Car Gen3 Hardware
User's Manual Rev.0.51E or later.
Fixes: f9aece7344 ("pinctrl: sh-pfc: Initial R8A7796 PFC support")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add pins, groups, and functions for MSIOF on R-Car H3 ES2.0.
Extracted from a big patch in the BSP by Takeshi Kihara, with
corrections for MSIOF3 SS1_E/SS2_E pins and SS2_E mux.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This patch fixes the incorrect IPSR register value definitions for
MSIOF3_{SS1,SS2}_E pin functions.
This is a correction to the incorrect implementation of IPSR register pin
assignment of the specifications updated for R8A7795 ES2.0 SoC in R-Car
Gen3 Hardware User's Manual Rev.0.53E.
Fixes: b205914c8f ("pinctrl: sh-pfc: r8a7795: Add support for R-Car H3 ES2.0")
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
[geert: Reword, update Fixes for upstream]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On group configuration, bail out if setting one of the individual pins
fails. We don't need to roll-back, the pinctrl core will do this for us.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output
buffers without actually enabling input and/or output on a
pin. We are chiseling out some details of pin control
electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the
tree to use this pin controller and consolidate earlier
spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control.
All users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for
RK3228, RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register
access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes.
-----BEGIN PGP SIGNATURE-----
iQIcBAABAgAGBQJZXeUhAAoJEEEQszewGV1zcl8QAMZ6To2JBQeK0Qi+pik9ZbW7
CvnIFT7E4X45tstwFNKIgdQ1C/IcfzKpPSUDRUqi2nWJiWcuYgn3wQwQ5qbkGtaG
vne0KVChgFGkT2SwycUZy11JxuP75U73e27BwAruxHhwWo5PesUOjjkmUtMqdbNQ
VAwx6KoCBx1VBlb0uscbSSqFyAspdyeAHPEvSj4IpsqRZzT7YFqDm4C+uTnwavPx
ZLoTji0HCpPIAo4C8JUAvweWbpxMC1IMdfm9jRkZ4rR/gTFQXvK+9ssI6lxSK6a6
RiCJaAE6wQHKYm4LL0pGbW+aMGWRRRp8MERNmg8NgnWONcfCxYowoOYeYLeqPhAg
kWkFHlmjpfo/A79V6tmN32vCpeQd34XGCetMpI93TuZ42olniD2Puv6RscVaSP3T
3mIqydX9BY8iAviyMaLcHQeChaNdhLQi+AVjrn1VQjdkWn0C7uR++JznsyaxaI+S
cVadl6k8H393R1Qdvh3JdoL0owsntQxWVWCbR6fyAZTHHiLGEyvL1ceO/rbpSRrn
c8Ghk5s7f3DFltn7yWiV4k3KVhDPb5iK2dYP9uGCgqbigHWqlcB5PanRu1aGSFov
h/1VFEMagNCXQCrgGcIfmkEiwW3SqUsFaaoMLhlYpNb/ON3ihGgsZYiczWSj8l4L
yfCOoszuEsVkV1dFNAjA
=dUFL
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the big bulk of pin control changes for the v4.13 series:
Core:
- The documentation is moved over to RST.
- We now have agreed bindings for enabling input and output buffers
without actually enabling input and/or output on a pin. We are
chiseling out some details of pin control electronics.
New drivers:
- ZTE ZX
- Renesas RZA1
- MIPS Ingenic JZ47xx: also switch over existing drivers in the tree
to use this pin controller and consolidate earlier spread out code.
- Microschip MCP23S08: this driver is migrated from the GPIO
subsystem and totally rewritten to use proper pin control. All
users are switched over.
New subdrivers:
- Renesas R8A7743 and R8A7745.
- Allwinner Sunxi A83T R_PIO.
- Marvell MVEBU Armada CP110 and AP806.
- Intel Cannon Lake PCH.
- Qualcomm IPQ8074.
Notable improvements:
- IRQ support on the Marvell MVEBU Armada 37xx.
- Meson driver supports HDMI CEC, AO, I2S, SPDIF and PWM.
- Rockchip driver now supports iomux-route switching for RK3228,
RK3328 and RK3399.
- Rockchip A10 and A20 are merged into a single driver.
- STM32 has improved GPIO support.
- Samsung Exynos drivers are split per ARMv7 and ARMv8.
- Marvell MVEBU is converted to use regmap for register access.
Maintenance:
- Several Renesas SH-PFC refactorings and updates.
- Serious code size cut for Mediatek MT7623.
- Misc janitorial and MAINTAINERS fixes"
* tag 'pinctrl-v4.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (137 commits)
pinctrl: samsung: Remove bogus irq_[un]mask from resource management
pinctrl: rza1: make structures rza1_gpiochip_template and rza1_pinmux_ops static
pinctrl: rza1: Remove unneeded wrong check for wrong variable
pinctrl: qcom: Add ipq8074 pinctrl driver
pinctrl: freescale: imx7d: make of_device_ids const.
pinctrl: DT: extend the pinmux property to support integers array
pinctrl: generic: Add output-enable property
pinctrl: armada-37xx: Fix number of pin in sdio_sb
pinctrl: armada-37xx: Fix uart2 group selection register mask
pinctrl: bcm2835: Avoid warning from __irq_do_set_handler
pinctrl: sh-pfc: r8a7795: Add PWM support
MAINTAINERS: Add Qualcomm pinctrl drivers section
arm: dts: dt-bindings: Add Renesas RZ/A1 pinctrl header
dt-bindings: pinctrl: Add RZ/A1 bindings doc
pinctrl: Renesas RZ/A1 pin and gpio controller
pinctrl: sh-pfc: r8a7792: Add SCIF1 and SCIF2 pin groups
pinctrl.txt: move it to the driver-api book
pinctrl: ingenic: checking for NULL instead of IS_ERR()
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD20
pinctrl: uniphier: fix WARN_ON() of pingroups dump on LD11
...
The irq chip callbacks irq_request/release_resources() have absolutely no
business with masking and unmasking the irq.
The core code unmasks the interrupt after complete setup and masks it
before invoking irq_release_resources().
The unmask is actually harmful as it happens before the interrupt is
completely initialized in __setup_irq().
Remove it.
Fixes: f6a8249f9e ("pinctrl: exynos: Lock GPIOs as interrupts when used as EINTs")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
structures rza1_gpiochip_template and rza1_pinmux_ops do not need to be
in global scope, so make them static.
Cleans up sparse warnings:
symbol 'rza1_gpiochip_template' was not declared. Should it be static?
symbol 'rza1_pinmux_ops' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Depending on compiler version:
drivers/pinctrl/pinctrl-rza1.c: In function ‘rza1_pinctrl_probe’:
drivers/pinctrl/pinctrl-rza1.c:1260:5: warning: ‘ret’ may be used uninitialized in this function [-Wmaybe-uninitialized]
if (ret)
^
Indeed, the result returned by platform_get_resource() was stored in
"res", not "ret". In addition, the correct error check would be
"if (!res)", as platform_get_resource() does not return an error code,
but returns NULL on failure.
However, as devm_ioremap_resource() verifies the validity of the passed
resource pointer anyway, the check can just be removed.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 5a49b644b3 ("pinctrl: Renesas RZ/A1 pin and gpio controller")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add SCIF1 and SCIF2 pin groups for R-Car V2H,
- Add EtherAVB, DU parallel RGB output, and PWM pin groups for R-Car
H3 ES2.0,
- Add pin and gpio controller support for RZ/A1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RSGM
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.13-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.13 (take two)
- Add SCIF1 and SCIF2 pin groups for R-Car V2H,
- Add EtherAVB, DU parallel RGB output, and PWM pin groups for R-Car
H3 ES2.0,
- Add pin and gpio controller support for RZ/A1.
of_device_ids are not supposed to change at runtime. All functions
working with of_device_ids provided by <linux/of.h> work with const
of_device_ids. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add output-enable generic pin configuration property.
This properties allows enabling/disabling pin's output capabilities
without actually driving any value on the line.
Acked-by: Rob Herring <robh@kernel.org>
[Added inline elaborations on buffer enabling/disabling]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The sdio_sb group is composed of 6 pins and not 5.
Reported-by: Ken Ma <make@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If north bridge selection register bit1 is clear, pins [10:8] are for
SDIO0 Resetn, Wakeup, and PDN while if bit1 is set, pins [10:8]are for
GPIO; when bit1 is clear, pin 9 and pin 10 can be used for uart2 RTSn
and CTSn, so bit1 should be added to uart2 group and it must be set
for both "gpio" and "uart" functions of uart2 group.
Signed-off-by: Ken Ma <make@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We get a warning during boot with enabled EARLY_PRINTK that
we try to set a irq_chip without data. This is caused by ignoring
the return value of irq_of_parse_and_map(). So avoid calling
gpiochip_set_chained_irqchip() in error case.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: 85ae9e512f ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pinctrl support for the PWM[0-6] pins.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Add SCIF1 and SCIF2 pin groups to the R8A7792 PFC driver.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
1. Split drivers per ARMv7 and ARMv8 architectures because there
is no need to compile everything on each of them.
2. Fix for possible NULL-pointer dereference after memory allocation
failure.
3. Cleanups (silencing cast warnings, constify, removal of unneeded
casts, removal of modular boiler-plate).
-----BEGIN PGP SIGNATURE-----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=CVoA
-----END PGP SIGNATURE-----
Merge tag 'samsung-pinctrl-4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into devel
Samsung pinctrl drivers update for v4.13:
1. Split drivers per ARMv7 and ARMv8 architectures because there
is no need to compile everything on each of them.
2. Fix for possible NULL-pointer dereference after memory allocation
failure.
3. Cleanups (silencing cast warnings, constify, removal of unneeded
casts, removal of modular boiler-plate).
The H3 ES1.x and H3 ES2.0 have identical pinmuxing for the parallel RGB
output support.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This commit adds a pinctrl driver for the CP110 part of the Marvell
Armada 7K and 8K SoCs. The Armada 7K has a single CP110, where almost all
the MPP pins are available. On the other side, the Armada 8K has two
CP110, and the available MPPs are split between the master CP110 (MPPs 32
to 62) and the slave CP110 (MPPs 0 to 31).
The register interface to control the MPPs is however the same as all
other mvebu SoCs, so we can reuse the common pinctrl-mvebu.c logic.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Reviewed-by: Shadi Ammouri <shadi@marvell.com>
[updated for mvebu pinctrl and 4.9 changes:
- converted to simple_mmio
- converted to syscon/regmap
- removed unimplemented .remove function
- dropped DTS changes
- defered gpio ranges to DT
- fixed warning
- properly set soc->nmodes
-- rmk]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[ add missing MPP[61:56] function 14 (SDIO)
-- Konstantin Porotchkin]
Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
[ allow to properly register more then one instance of this driver
-- Grzegorz Jaszczyk]
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[ - rebased on 4.12-rc1
- fixed the 80 character limit for mvebu_mpp_mode array
- aligned the compatible name on the ones already used
- fixed the MPP table for CP110: some MPP are not available on Armada 7K
-- Gregory CLEMENT]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Tested-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This commit adds a pinctrl driver for the pin-muxing controller found in
the AP806 part of the Marvell Armada 7K and 8K SoCs. Its register
interface is compatible with the one used by previous mvebu pin
controllers, so the common logic in drivers/pinctrl/mvebu/pinctrl-mvebu.c
is used.
Signed-off-by: Hanna Hawa <hannah@marvell.com>
Reviewed-by: Shadi Ammouri <shadi@marvell.com>
[updated for mvebu pinctrl changes
- converted to simple_mmio
- removed unimplemented .remove function
- removed DTS description
- converted to use syscon/regmap
--rmk]
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Armada 8040 also needs orion pinctrl, and as these symbols are only
selected, there's no need to make them depend on PLAT_ORION.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The offset property of the pinctrl node, when a regmap is used in the
device tree, was never used nor documented in the binding. Moreover, the
compatible string is enough to let the driver know which offset using.
So this patch removes the property and move the information at the driver
level.
Reviewed-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add Tsin A pins to bank DV and X.
We don't have a driver for the tsin yet but since the tsin A pinmux is
enabled by default at boot time, declaring this pinmux is required to
properly operate on GPIOX.
Without this change, GPIOX 8, 9, 10 and 11 can't be driven as GPIO output
as the tsin A seems to have priority.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add pins, groups, and a function for EtherAVB on R-Car H3 ES2.0.
Extracted from a big patch in the BSP by Takeshi Kihara.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This adds pinctrl/GPIO support for Intel Cannon Lake PCH. The Cannon
Lake PCH GPIO is based on newer version of the Intel GPIO hardware.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On some SoCs not all pins in a group use the same mode when a certain
function is muxed out of them. This makes it possible to specify mode per
pin as an array instead in addition to single integer.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Intel GPIO hardware has a concept of pad groups, which means 1 to 32
pads occupying their own GPI_IS, GPI_IE, PAD_OWN and so on registers. The
existing hardware has the same amount of pads in each pad group (except the
last one) so it is possible to use community->gpp_size to calculate start
offset of each register.
With the next generation SoCs the pad group size is not always the same
anymore which means we cannot use community->gpp_size for register offset
calculations directly.
To support variable size pad groups we introduce struct intel_padgroup that
can be filled in by the client drivers according the hardware pad group
layout. The core driver will always use these when it performs calculations
for pad register offsets. The core driver will automatically populate pad
groups based on community->gpp_size if the driver does not provide any.
This makes sure the existing drivers still work as expected.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Chuah, Kim Tatt <kim.tatt.chuah@intel.com>
Signed-off-by: Tan Jui Nee <jui.nee.tan@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The R_PIO on the A83T is almost the same as the one found on the A64,
except that the CIR_RX function was moved from pin PL11 to pin PL12.
Add a driver for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use consistent license headers for Broadcom files by
placing additional comments outside of standard legal header.
Also, update legal header to 2017 format as "Broadcom Corporation"
has changed to "Broadcom".
Signed-off-by: Scott Branden <scott.branden@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
struct irq_domain_ops is not modified, so it can be made const.
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In stm32_pconf_parse_conf function, stm32_pmx_gpio_set_direction is
called with wrong parameter value. Indeed, using NULL value for range
will raise an oops.
Fixes: aceb16dc2d ("pinctrl: Add STM32 MCUs support")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AMD pinctrl driver uses a chained interrupt to demultiplex the GPIO
interrupts. Kevin Vandeventer reported, that his new AMD Ryzen locks up
hard on boot when the AMD pinctrl driver is initialized. The reason is an
interrupt storm. It's not clear whether that's caused by hardware or
firmware or both.
Using chained interrupts on X86 is a dangerous endavour. If a system is
misconfigured or the hardware buggy there is no safety net to catch an
interrupt storm.
Convert the driver to use a regular interrupt for the demultiplex
handler. This allows the interrupt storm detector to catch the malfunction
and lets the system boot up.
This should be backported to stable because it's likely that more users run
into this problem as the AMD Ryzen machines are spreading.
Reported-by: Kevin Vandeventer
Link: https://bugzilla.suse.com/show_bug.cgi?id=1034261
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There is no link between the number of elements of tab which contains all
pin desc (located in each pinctrl-stm32xxxx.c files) and the pin number
(defined in the tab).
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add GPIO interrupt information to pinctrl data. Added to the original
version from Jerome was data for Meson GXL.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
After commit 34e61801a3 "pinctrl: meson-gxbb: Add missing GPIODV_18
pin entry" I started to get the following warning:
"meson-pinctrl c8834000.periphs:pinctrl@4b0: names 119 do not match
number of GPIOs 120"
It turned out that not the mentioned commit has a problem, it just
revealed another problem which had existed before.
There is no PIN GPIOX_22 on Meson GXBB.
Fixes: 468c234f9e ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
For S5Pv210 retention control, the driver stores the iomem pointer from
of_iomap() under a void pointer member. This makes sparse unhappy:
drivers/pinctrl/samsung/pinctrl-exynos.c:664:36: warning: incorrect type in argument 1 (different address spaces)
drivers/pinctrl/samsung/pinctrl-exynos.c:664:36: expected void const volatile [noderef] <asn:2>*addr
drivers/pinctrl/samsung/pinctrl-exynos.c:664:36: got void *
The iomem pointer is used safely (stored under priv by
s5pv210_retention_init(), used by s5pv210_retention_disable()) thus we
can add explicit casts to iomem to silence the warning.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Check if kmemdup failed during wakeup banks initialization. Otherwise
NULL pointer would be stored under "irq_chip" member of bank and later
dereferenced in interrupt handler.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Static exynos_irq_chip structures, containing driver specific data, are
referenced only through opaque data pointer in const of_device_id table.
The contents of pointed memory (exynos_irq_chip structure itself) is
then copied with kmemdup() during wakeup initialization so
exynos_irq_chip can be made const for code safenes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Exynos pinctrl drivers contain pretty big per-SoC data structures. The
pinctrl-exynos object file contained code and data for both ARMv7 and
ARMv8 SoCs thus it grew big. There will not be a shared image between
ARMv7 and ARMv8 so there is no need to combine all of this into one
driver.
Splitting the data allows to make it more granular (e.g. code related to
ARMv8 Exynos is self-contained), slightly speed up the compilation and
reduce the effective size of compiled kernel.
The common data structures and functions reside still in existing
pinctrl-exynos.c. Only the SoC-specific parts were moved out to new
files. Except marking few functions non-static and adding them to
header, there were no functional changes in the code.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
- Add PWM, AVB MDIO/MII, and sound pin groups on R-Car M3-W,
- Add support for RZ/G1M and RZ/G1E,
- Small fixes and cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JT2m
-----END PGP SIGNATURE-----
Merge tag 'sh-pfc-for-v4.13-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: sh-pfc: Updates for v4.13
- Add PWM, AVB MDIO/MII, and sound pin groups on R-Car M3-W,
- Add support for RZ/G1M and RZ/G1E,
- Small fixes and cleanups.
This patch ensures that pin is correctly set as gpio input when it is used
as an interrupt.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
With "SPI_MASTER=y && I2C=m", we can build mcp23s08 as a built-in driver,
which then results in a link failure:
drivers/pinctrl/built-in.o: In function `mcp23s08_probe_one.isra.0':
:(.text+0x7910): undefined reference to `__devm_regmap_init_i2c'
drivers/pinctrl/built-in.o: In function `mcp23s08_init':
:(.init.text+0x110): undefined reference to `i2c_register_driver'
drivers/pinctrl/built-in.o: In function `mcp23s08_exit':
:(.exit.text+0x3c): undefined reference to `i2c_del_driver'
To avoid the problem, this adds another dependency on I2C that enforces
mcp23s08 to be a loadable module whenever the I2C core is a module.
Fixes: 64ac43e6fa ("gpio: mcp23s08: move to pinctrl")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As we added A20 support to A10 pinctrl driver, now we can delete the
dedicated A20 pinctrl driver, which is duplicated code.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
[Drop Makefile entry]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
As A20 is designed as a pin-compatible upgrade of A10, their pin
controller are very similar, and can share one driver.
Add A20 support to the A10 driver.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Allwinner A10, A20 and R40 SoCs have similar GPIO layout.
Add SoC definitions in pinctrl-sunxi.h, in order to merge A20 support
into A10 driver, and add R40 support into it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are 2 IP blocks pin routes need to be switched, that are
uart2dbg, pcie_clkreq.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are 8 IP blocks pin routes need to be switched, that are
uart2dbg, gmac-m1-optimized, pdm, spi, i2s2, card, tsp, cif.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are 9 IP blocks pin routes need to be switched, that are
pwm-0, pwm-1, pwm-2, pwm-3, sdio, spi, emmc, uart2, uart1.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On the some rockchip SOCS, some things like rk3399 specific uart2 can use
multiple pins. Somewhere between the pin io-cells and the uart it seems
to have some sort of switch to decide to which pin to actually route the
data.
+-------+ +--------+ /- GPIO4_B0 (pinmux 2)
| uart2 | -- | switch | --- GPIO4_C0 (pinmux 2)
+-------+ +--------+ \- GPIO4_C3 (pinmux 2)
(switch selects one of the 3 pins base on the GRF_SOC_CON7[BIT0, BIT1])
The routing switch is determined by one pin of a specific group to be set
to its special pinmux function. If the pinmux setting is wrong for that
pin the ip block won't work correctly anyway.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix compile errors due to missing OF.
Cc: Paul Cercueil <paul@crapouillou.net>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Amlogic Meson GXL SoCs embeds an 10/100 Ethernet PHY, this patchs enables
the Link and Activity LEDs signals.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the AO and EE domain CEC pins for the Amlogic Meson GXL SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the AO and EE domain CEC pins for the Amlogic Meson GXBB SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AO SPDIF pins were incorrectly defined with the EE pin offset.
Fixes: b840d649f9 ("pinctrl: meson: gxl: add spdif output pins")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The AO I2S pins were incorrectly defined with the EE pin offset.
Fixes: 2899adf042 ("pinctrl: meson: gxl: add i2s output pins")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GPIODV_18 entry was missing in the original driver push.
Fixes: 468c234f9e ("pinctrl: amlogic: Add support for Amlogic Meson GXBB SoC")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fixups here tend to be more of a conglomerate of some of the other
repeated/systematic ones we've seen in the earlier pinctrl cleanups.
We remove module.h from code that isn't doing anything modular at
all; if they have __init sections, then replace it with init.h
One driver has a .remove that would be dispatched on module_exit,
and as that code is essentially orphaned, so we remove it. In case
anyone was previously doing the (pointless) unbind to get to that
function, we disable unbind for this one driver as well.
A couple bool drivers (hence non-modular) are converted over to
to builtin_platform_driver().
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Eric Anholt <eric@anholt.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jon Mason <jonmason@broadcom.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Ray Jui <rjui@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Sherman Yin <syin@broadcom.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: linux-gpio@vger.kernel.org
Cc: linux-rpi-kernel@lists.infradead.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
None of the Kconfigs for any of these drivers are tristate,
meaning that they currently are not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the drivers there is no doubt they are builtin-only. All
drivers get similar changes, so they are handled in batch.
We remove module.h from code that isn't doing anything modular at
all; if they have __init sections, then replace it with init.h.
A couple drivers have module_exit() code that is essentially orphaned,
and so we remove that.
Quite a few bool drivers (hence non-modular) are converted over to
to builtin_platform_driver().
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Pritesh Raithatha <praithatha@nvidia.com>
Cc: Ashwini Ghuge <aghuge@nvidia.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use of_device_get_match_data() instead of of_match_device().
It allows us to remove the forward declaration of pcs_of_match.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There are a couple of issues with group_desc initialization in function
zx_pinctrl_build_state().
- num_pins is not initialized and remains zero.
- pins shouldn't be initialized with a pointer to variable in the
stack.
With them fixed, pin_request() in pinmux_enable_setting() can be invoked
correctly.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPICC controller has dedicated SPI pins, this patchs add the pins
definition in the GXBB pinctrl driver
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SPICC controller has dedicated SPI pins, this patchs add the pins
definition in the GXL pinctrl driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl-exynos.h header is included only once so till now it did not
require an include guard. However adding such is harmless and makes
code prepared for more inclusions.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Fixups here tend to be more all over the map vs. some of the other
repeated/systematic ones we've seen elsewhere.
We remove module.h from code that isn't doing anything modular at
all; if they have __init sections, then replace it with init.h
A couple drivers have module_exit() code that is essentially orphaned,
and so we remove that.
There are no module_init replacements, so we have no concerns wrt.
initcall ordering changes as per some of the other cleanups.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
We use well known standard names for functions that have name, such as
I2C, SPI, SPDIF, etc..
Fix the function name of SPDIF, which was named OWA (One Wire Audio)
based on Allwinner datasheets.
Fixes: 4730f33f0d ("pinctrl: sunxi: add allwinner A83T PIO controller
support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We use well known standard names for functions that have name, such as
I2C, SPI, SPDIF, etc..
Fix the function name of SPDIF, which was named OWA (One Wire Audio)
based on Allwinner datasheets.
Fixes: 4730f33f0d ("pinctrl: sunxi: add allwinner A83T PIO controller
support")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
To set the mux mode of a pin two bits must be set. Up to now this is
implemented using the following idiom:
writel(mask, reg + CLR);
writel(value, reg + SET);
. This however results in the mux mode being 0 between the two writes.
On my machine there is an IC's reset pin connected to LCD_D20. The
bootloader configures this pin as GPIO output-high (i.e. not holding the
IC in reset). When Linux reconfigures the pin to GPIO the short time
LCD_D20 is muxed as LCD_D20 instead of GPIO_1_20 is enough to confuse
the connected IC.
The same problem is present for the pin's drive strength setting which is
reset to low drive strength before using the right value.
So instead of relying on the hardware to modify the register setting
using two writes implement the bit toggling using read-modify-write.
Fixes: 17723111e6 ("pinctrl: add pinctrl-mxs support")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It turns out there are quite many Chromebooks out there that have the
same keyboard issue than Acer Chromebook. All of them are based on
Intel_Strago reference and report their DMI_PRODUCT_FAMILY as
"Intel_Strago" (Samsung Chromebook 3 and Cyan Chromebooks are exceptions
for which we add separate entries).
Instead of adding each machine to the quirk table, we use
DMI_PRODUCT_FAMILY of "Intel_Strago" that hopefully covers most of the
machines out there currently.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=194945
Suggested: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver supports using mcp23xxx as interrupt controller, so
let's drop all comments stating otherwise.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves irq property handling from spi/i2c specific code into
the generic mcp23s08_probe_one. This is possible because the
device properties are named equally.
As a side-effect this drops support for setting the properties via
pdata, which has no mainline users. If boardcode wants to enable
the chip as interrupt controller it can attach the device properties
instead.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simplify spi pdata handling, so that it uses pdata when available
and falls back to reading device properties otherwise.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Simplify i2c pdata handling, so that it uses pdata when available
and falls back to reading device properties otherwise.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Switching to devm_gpiochip_add_data simplifies the driver's
cleanup routine and safes a few loc.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Let's remove a few lines of code by using managed memory for mcp
variable.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
i2c-core and spi-core already assign the irq, so we
can drop the additional call from the mcp driver.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The driver compiles & works perfectly fine without OF_GPIO on x86,
so lets drop the dependency.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Instead of using custom caching, this switches to regmap based
caching. Before the conversion the debugfs file used uncached
values, so that it was easily possible to see power-loss related
problems. The new code will check and recover at this place.
The patch will also ensure, that irqs are not cleared by checking
register status in debugfs.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mcp23s08 support configuration of the pullups using the
pinconf framework. This removes the custom pullup configuration
from platform data, which has no upstream users.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mcp23xxx device have configurable 100k pullup resistors. This adds
support for enabling them using pinctrl's pinconf interface.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This moves the mcp23s08 driver from gpio to pinctrl. Actual
pinctrl support for configuration of the pull-up resistors
follows in its own patch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Andre Przywara <andre.przywara@arm.com> noticed that we can get the
following warning with -EPROBE_DEFER:
"WARNING: CPU: 1 PID: 89 at drivers/base/dd.c:349
driver_probe_device+0x2ac/0x2e8"
Let's fix the issue by removing the indices as suggested by
Tejun Heo <tj@kernel.org>. All we have to do here is kill the radix
tree.
I probably ended up with the indices after grepping for removal
of all entries using radix_tree_for_each_slot() and the first
match found was gmap_radix_tree_free(). Anyways, no need for
indices here, and we can just do remove all the entries using
radix_tree_for_each_slot() along how the item_kill_tree() test
case does.
Fixes: c7059c5ac7 ("pinctrl: core: Add generic pinctrl functions for managing groups")
Fixes: a76edc89b1 ("pinctrl: core: Add generic pinctrl functions for managing groups")
Reported-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Gustavo A. R. Silva