This patch modifies location of debugfs entries and their naming
conventions to support multiple wireless cards on pcie host.
Selected approach is to use separate directories for different
wireless cards in top-level qtnfmac debugfs directory.
Here is an example that clarifies the chosen naming conventions:
$ sudo ls /sys/kernel/debug/qtnfmac/
qtnfmac_pcie:0000:01:00.0
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ETSI region DFS slave device can operate in two modes on DFS channels:
- do on-channel radar detection and use higher Tx power
- don't do radar detection and use lower Tx power as a consequence
Allow user to control that behavior through qtnfmac module parameter.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Channel switch events from firmware should be processed only when STA
is already connected to BSS. On connect this notification is not needed
since full BSS info will be supplied by cfg80211_connect_result.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
size = struct_size(instance, entry, count);
or
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)
Based on the above, replace qtnf_cmd_acl_data_size() with the
new struct_size() helper.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use scan duration param for both active and passive scan dwell times.
Document what different types of dwell times are used for. Explicitly
specify that if unset, automatic selection by device firmware
will be used.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use control path to send EAPOL frames to make sure they are
sent with higher priority with aggregation disabled.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Allow to change netns for wireless interfaces created by qtnfmac driver.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch streamlines firmware state tracking. In particular, state
QTNF_FW_STATE_FW_DNLD_DONE is removed, states QTNF_FW_STATE_RESET and
QTNF_FW_STATE_DETACHED are merged into a single state. Besides, new
state QTNF_FW_STATE_RUNNING is introduced to distinguish between
the following two cases:
- firmware load succeeded, firmware init process is ongoing
- firmware init succeeded, firmware is fully functional
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Report that firmware is up and running only for successful firmware
download. Simplify qtnf_pcie_fw_boot_done: modify error path so that
no need to pass firmware dowload result to this function. Finally,
do not create debugfs entries if firmware download succeeded,
but core attach failed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In some regions, different regulatory limits (like max Tx power) may be
defined for different operating modes. As an example: in ETSI regions
DFS master devices may use higher transmit powers compared to DFS slave
devices. Update bands information in CHANGE_INTF command if mode of
operation changes.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pass DFS region as requested by regulatory core directly to firmware
so it can initialize radar detection block accordingly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently driver uses the same regulatory rules to register all wiphy
instances. This is not logically correct since each wiphy may have
different capabilities (different supported bands, EIRP etc).
Allow firmware to pass regulatory rules for each MAC separately.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use REGULATORY_CUSTOM_REG flag only if firmware advertised a custom
regulatory domain prior to wiphy registration. Use REGULATORY_STRICT_REG
flag only if firmware knows its regulatory domain.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently only a portion of per-channel information is passed to
firmware. Extend logic to pass all useful per-channel data.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Before regulatory notifier is invoked by a wireless core, it will
update band information for the wiphy. Pass this information to
firmware together with new region alpha2 code.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Error reporting in qtnf_cfg80211_reg_notifier only requires to print
one type of message and an error code. Firmware will report success
for an attempt to set regulatory region to the same value,
so no special handling is required for this case.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wireless core calls regulatory notifier for each wiphy and it only
guarantees that bands info is updated for this particular wiphy prior
to calling a notifier. Hence updating all wiphy which belong to driver
in a single notifier callback is redundant and incorrect.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the case of SAE AP, drivers offload authentication to user-space
software, e.g. hostapd. For FullMAC drivers the procedure is as follows.
If auth_type is SAE and user space indicates external authentication
capability, then driver requests authentication offload to user-space
software using cfg80211_external_auth_request call. From that point,
auth frame exchange is performed transparently for driver: user-space
software sends/receives mgmt frames using mgmt_tx/mgmt_frame_register
cfg80211 callbacks. As soon as authenitcation is completed, user-space
software notifies driver about its status using external_auth cfg80211
callback.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the case of OWE, STA should be able to pass DH IEs from AP assoc
responses to wpa_s for processing. For this purpose DH IEs are
received from firmware in BSS_JOIN events and passed to wireless
core and then to wpa_s as additional optional rsp_ies parameter
for cfg80211_connect_result.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Igor Mitsyanko <imitsyanko@quantenna.com>
Cc: Avinash Patil <avinashp@quantenna.com>
Cc: Sergey Matyukevich <smatyukevich@quantenna.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use existing variable with dereferenced cmd_id field.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove declarations for inexistent functions from bus.h header.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure that valid BSS entry exists in wireless core record
even in the case of successful connect reported by firmware.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace textual license with SPDX-License-Identifier.
Add an SPDX-License-Identifier for the Makefile.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not reject RETRY changes in driver. This decision
should belong to firmware.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Host wireless stack uses u32 type for RTS/FRAG threshold values.
Switch to u32 in driver: pass u32 values to firmware and let
firmware properly adapt these values according to its
internal representation.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Advertise WIPHY_FLAG_4ADDR_STATION capability to wireless core. Send
use4addr interface change flag to firmware in change_virtual_intf
cfg80211 callback.
In order to enable adding wireless station interface to bridge
one should turn on 4addr mode using the following command:
$ iw dev wlan0 set 4addr on
$ brctl addif br0 wlan0
If this commands succeeds, then interface can be added to bridge.
Note that when wireless interface is added to bridge, wpa_supplicant
should be started with appropriate -b <brname> parameter, e.g:
$ wpa_supplicant -Dnl80211 -iwlan0 -c/path/to/wpa.conf -b br0
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the current implementation INTx interrupt is deasserted after the
control path processing. However this may lead to missed interrupts
from the wireless card. For instance, this may happen as a result
of control path activity, when another interrupt arrives before
INTx is deasserted.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support of EBUSY error code for remote procedures over QLINK protocol.
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes the following warnings:
- smatch
drivers/net/wireless/quantenna/qtnfmac/commands.c:132 qtnf_cmd_send_with_reply() warn: variable dereferenced before check 'resp' (see line 117)
drivers/net/wireless/quantenna/qtnfmac/commands.c:716 qtnf_cmd_get_sta_info() error: uninitialized symbol 'var_resp_len'.
drivers/net/wireless/quantenna/qtnfmac/commands.c:1668 qtnf_cmd_get_mac_info() error: uninitialized symbol 'var_data_len'.
drivers/net/wireless/quantenna/qtnfmac/commands.c:1697 qtnf_cmd_get_hw_info() error: uninitialized symbol 'info_len'.
drivers/net/wireless/quantenna/qtnfmac/commands.c:1753 qtnf_cmd_band_info_get() error: uninitialized symbol 'info_len'.
drivers/net/wireless/quantenna/qtnfmac/commands.c:1782 qtnf_cmd_send_get_phy_params() error: uninitialized symbol 'response_size'.
drivers/net/wireless/quantenna/qtnfmac/commands.c:2438 qtnf_cmd_get_chan_stats() error: uninitialized symbol 'var_data_len'.
- gcc-8.2.1
drivers/net/wireless/quantenna/qtnfmac/commands.c: In function 'qtnf_cmd_send_with_reply':
drivers/net/wireless/quantenna/qtnfmac/commands.c:133:54: error: 'resp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for QSR1000/QSR2000 family of chipsets
to qtnfmac_pcie platform driver.
QSR1000/QSR2000 (aka Topaz) is a family of 80MHz, 11ac Wave2,
4x4/2x4/2x2 chips, including single and dual band devices.
Depending on specific chip model and firmware in use, either
STA or both STA and AP modes are supported.
Patch adds Topaz support to qtnfmac_pcie driver. Proper platform
bus will be selected on probing based on chip ID.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Andrey Shevchenko <ashevchenko@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Single PCIe driver can identify hardware type by reading CHIP ID at
probe time and invoking a correct initialization sequence.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove redundant information from Pearl platform headers.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change pcie bus layer licensing information to SPDX format.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix checkpatch warning: use preferred 'help' option in Kconfig.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Current implementation of dump_station cfg80211 callback supports
AP mode only. Add support for STA mode as well: by default in STA
mode this callback is supposed to return AP on managed interface.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Command responses and events from the firmware are copied twice in
control path: at first in shm core (qtnf_shm_handle_new_data) and
then in pcie bus drivers (qtnf_pcie_control_rx_callback). There
is no need to copy this data twice, it can be done only once
in rx callbacks.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware supports scan dwell time tuning for various types of scans.
Enable support for this feature:
- advertise capability to configure channel dwell time to host
- pass scan dwell parameters to wireless card in scan request
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Notify firmware to flush cache before scanning when needed.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On disconnect wireless core attempts to remove all the supported keys.
Following cfg80211_ops conventions, firmware returns -ENOENT code
for the out-of-bound key indexes. This is a normal behavior,
so no need to report errors for this case.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Driver retrieves information about supported extended capabilities
from wireless card. However this information is not propagated
further to Linux wireless core. Fix this by setting extended
capabilities fields of wiphy structure.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SGI should be passed to wireless core as a part of rate structure.
Otherwise wireless core performs incorrect rate calculation when
SGI is enabled in hardware but not reported to host.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Do not cancel scan in disconnect callback. If there is an active scan,
it will be cancelled by firmware, then host driver will be properly
notified by event.
Cancelling scan in disconnect callback occasionally may lead to the
following race issue. Host is able to queue one scan after scan
abort in disconnect callback, and another scan after scan abort
in event handler. As a result, firmware receives second scan
before the first scan completes.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unify command error handling using qtnf_cmd_resp_result_decode
function. Do not duplicate error messages in command handlers
and cfg80211 callbacks: report 'cmd exec fail' only on control
path internal failure. Remove redundant 'unlikely' macros.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Several members of pwr-MAC structure are re-initialized several times
together with per-VIF initialization. Fix that and simplify the code.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case firmware reports that it can not do OBSS scanning for 40MHz
2.4GHz channels itself, tell userpsace to do that instead by setting
NL80211_FEATURE_NEED_OBSS_SCAN flag.
Signed-off-by: Igor mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When cfg80211 disconnect callback is triggered and command is
processed by firmware, disconnect event with local parameter
set must be sent immediately. Indicating that it's a "local"
event (not from AP) will help upper layers to process this
event correctly.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove STA connection states tracking from driver.
Leave it wireless core on host and to firmware.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make sure that wifi device is of supported variant by checking it's CHIP ID
before completing a probe sequence.
Signed-off-by: Igor Mitsyanko <igor.mitsyanko.os@quantenna.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sergey Matyukevich