Audio IP need the spba clock, but original clock name "dma" is not
accurate, so change it to name "spba". The audio driver has been
using the new name "spba", the binding document has been updated.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It can improve the USB performance when choosing larger
burst size at some systems (bus size is larger), there is
no side effect if this burst size is larger than bus size.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
After setting ahb burst configuration as 0, we can increase tx/rx
burst size, it will improve the USB performance
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The correct core clock of spdif is SPDIF_GCLK, which is added to
clock tree. So the dts also need to be updated.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- Cleanups for Renesas shmobile platforms
- Lots of added devices on LPC18xx
- Lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some branches
that are primarily merged through the clock tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=D2Pm
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"Ladies and gentlemen, we proudly announce to you the latest branch of
ARM device tree contents for the mainline kernel. Come and see, come
and see!
No less than twentythree thousand lines of additions! Just imagine the
joy you will have of using your mainline kernel on newly supported
hardware such as Rockchip Chromebooks, Freescale i.MX6UL boards or
UniPhier hardware!
For those of you feeling less adventurous, added hardware support on
platforms such as TI DM814x and Gumstix Overo platforms might be more
of your liking.
We've got something for everyone here!
Ahem. Cough. So, anyway...
This is the usual large batch of DT updates. Lots and lots of smaller
changes, some of the larger ones to point out are:
- Rockchip veyron (Chromebook) support, as well as several other new boards
- DRM support on Atmel AT91SAM9N12EK
- USB additions on some Allwinner platforms
- Mediatek MT6580 support
- Freescale i.MX6UL support
- cleanups for Renesas shmobile platforms
- lots of added devices on LPC18xx
- lots of added devices and boards on UniPhier
There's also some dependent code added here, in particular some
branches that are primarily merged through the clock tree"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (389 commits)
ARM: tegra: Add gpio-ranges property
ARM: tegra: Fix AHB base address on Tegra20, Tegra30 and Tegra114
ARM: tegra: Add Tegra124 PMU support
ARM: tegra: jetson-tk1: Add GK20A GPU DT node
ARM: tegra: venice2: Add GK20A GPU DT node
ARM: tegra: Add IOMMU node to GK20A
ARM: tegra: Add CPU regulator to the Jetson TK1 device tree
ARM: tegra: Add entries for cpufreq on Tegra124
ARM: tegra: Enable the DFLL on the Jetson TK1
ARM: tegra: Add the DFLL to Tegra124 device tree
ARM: dts: zynq: Add devicetree entry for Xilinx Zynq reset controller.
ARM: dts: UniPhier: fix PPI interrupt CPU mask of timer nodes
ARM: dts: rockchip: correct regulator power states for suspend
ARM: dts: rockchip: correct regulator PM properties
ARM: dts: vexpress: Use assigned-clock-parents for sp810
pinctrl: tegra: Only set the gpio range if needed
arm: boot: dts: am4372: add ARM timers and SCU nodes
ARM: dts: AM4372: Add the am4372-rtc compatible string
ARM: shmobile: r8a7794 dtsi: Add CPG/MSTP Clock Domain
ARM: shmobile: r8a7793 dtsi: Add CPG/MSTP Clock Domain
...
snvs is MFP device. Change dts to use syscon to allocate register resource.
snvs power off also switch to common syscon-poweroff
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PCIe interrupts are also routed through the GPC. This has been
missed from the conversion to stacked IRQ domains as the PCIe
controller uses an explicit interrupt map and thus doesn't inherit
the SoC global interrupt parent.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Cc: <stable@vger.kernel.org> # 4.1
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The CODA960 VPU is part of the PU power domain. Add power-domains
phandle so it can be associated with the PU generic pm domain for
power gating.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Currently the HDMI controller is a child device of the AIPS bus in the
DT which is clearly wrong. Move it to the right location.
This introduces no functional change it just aligns the DT representation
with reality.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since PWMs are only useful if they are actually connected to an output pin,
let users enable them explicitly in their device trees where they should
also set up the pin configuration.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The PU regulator is enabled during boot, but not necessarily always-on.
It can be disabled by the generic pm domain framework when the PU power
domain is shut down. The ramp delay of 150 us might be a bit conservative,
the value is taken from the Freescale kernel.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The PGC that is part of GPC controls isolation and power sequencing of the
power domains. The PU power domain will be handled by the generic pm domain
framework. It needs a phandle to the PU regulator to turn off power when
the domain is disabled, and a list of phandles to all clocks that must be
enabled during powerup for reset propagation.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The chipidea driver adds an extra line of spam to the log when a
host-only chipidea instance is left set to the default of a dual role
controller.
[ 2.010873] ci_hdrc ci_hdrc.1: doesn't support gadget
Set the dr_mode property to host on all the host-only nodes
to avoid this warning.
Signed-off-by: Matt Porter <mporter@konsulko.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
IMX6 has been (ab)using the gic_arch_extn to provide
wakeup from suspend, and it makes a lot of sense to convert
this code to use stacked domains instead.
This patch does just this, updating the DT files to actually
reflect what the HW provides.
BIG FAT WARNING: because the DTs were so far lying by not
exposing the fact that the GPC block is actually the first
interrupt controller in the chain, kernels with this patch
applied wont have any suspend-resume facility when booted
with old DTs, and old kernels with updated DTs won't even boot.
Tested-by: Stefan Agner <stefan@agner.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
It may be useful to disable the internal rtc snvs-rtc because an
external rtc is available. This patch adds a label so that board files
can disable this rtc.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The MIPI DSI node contains some ports which represent possible DRM CRTCs
it can connect with. Each port has a 'reg' property embedded. This
property will be wrongly interpretted by the MIPI DSI bus driver, because
the driver will take each subnode which contains a 'reg' property as a
DSI peripheral device. This patch moves the existing MIPI DSI ports into
a new 'ports' node so that the MIPI DSI bus driver may distinguish its
DSI peripheral device(s) from the existing ports.
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new platforms
and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of DTS
contents from GPL to GPLv2+/X11 so that the same files can be reused in
other non-GPL projects more easily. There's also been changes to the
DT Makefile to make it a little less conflict-ridden and churny down
the road.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=XEw1
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC DT updates from Olof Johansson:
"DT changes continue to be the bulk of our merge window contents.
We continue to have a large set of changes across the board as new
platforms and drivers are added.
Some of the new platforms are:
- Alphascale ASM9260
- Marvell Armada 388
- CSR Atlas7
- TI Davinci DM816x
- Hisilicon HiP01
- ST STiH418
There have also been some sweeping changes, including relicensing of
DTS contents from GPL to GPLv2+/X11 so that the same files can be
reused in other non-GPL projects more easily. There's also been
changes to the DT Makefile to make it a little less conflict-ridden
and churny down the road"
* tag 'dt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (330 commits)
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
...
According to Documentation/devicetree/bindings/media/coda.txt:
- clock-names : Should be "ahb", "per"
The OCRAM clock is already provided inside the ocram node, so remove the OCRAM
clock from the VPU node.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Commit a04a0b6fed ("ARM: dts: imx6qdl: Enable CODA960 VPU") lost the
fix for the CODA960 interrupt order during a rebase before being applied.
This patch adds the missing bit and brings the interrupts and
interrupt-names properties back in sync.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
All chips of i.mx6 can be powered off by programming SNVS.
For example :
On i.mx6q-sabresd board, PMIC_ON_REQ connect with external
pmic ON/OFF pin, that will cause the whole PMIC powered off
except VSNVS. And system can restart once PMIC_ON_REQ goes
high by push POWRER key.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This patch adds links to the on-chip SRAM and reset controller nodes
and switches the interrupts. Make the BIT processor interrupt, which exists on
all variants, the first one. The JPEG unit interrupt, which does not exist on
i.MX27 and i.MX5 thus is an optional second interrupt.
Use different compatible strings for i.MX6Q/D and i.MX6S/DL, as they have to
load separate firmware images for some reason.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Original gpt per clk parent is from ipg_per clk which
may be scaled when system enter low bus mode, as ipg
clk will be lower in low bus mode, to keep system clk
NOT drift, select gpt per clk parent from OSC which
is at fixed freq always.
On i.mx6qdl, add a osc_per clk source for i.mx6q
TO > 1.0 and all i.MX6dl SoC.
On i.mx6sx, just make gpt per clk from OSC.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Baud clock is used for bit clock generation in master mode. Ipg clock
is peripheral clock and peripheral access clock.
Signed-off-by: Shengjiu Wang <shengjiu.wang@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Fixes "imx6q-pcie 1ffc000.pcie: missing *config* reg space"
error exposed by new versions of the designware pcie driver.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds simple-card support to the i.MX SoCs.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Since commit 98ea6ad2ed (ARM: dts: imx6: use imx51-ssi) the mx6 ssi is
compatible with imx51, so align all the mx6 variant ssi compatible strings as:
compatible = "fsl,<imx6-soc>-ssi", "fsl,imx51-ssi";
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
When booting a board that does not have a keypad (such as imx6q-sabresd) the
following error is seen on boot:
imx-keypad 20b8000.kpp: OF: linux,keymap property not defined in /soc/aips-bus@02000000/kpp@020b8000
imx-keypad 20b8000.kpp: failed to build keymap
imx-keypad: probe of 20b8000.kpp failed with error -2
Let's disable the keypad functionality in the dtsi files and let each board dts
enable it when needed.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
All dtsi files where already moved to generic dma bindings. Remove the
old non-generic DMA properties.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The S/PDIF rxtx4 and rxtx6 clock inputs are "ESAI_HCKT" and "MLB clock",
respectively, according to the SoC documentation, and they are currently
mapped to clocks "esai" and "mlb".
However, they do not seem to actually work correctly. Testing on a
Cubox-i system with fsl_spdif driver forced to select one of those as
input will result in I/O errors on audio playback, which I believe means
missing clock signal.
Possibly the "ESAI_HCKT" and "MLB clock" refer to some other clocks
related to ESAI and MLB, or we are missing something else.
Since audio playback will not work if fsl_spdif selects these clocks
(which happens rarely), set the inputs do dummy clocks, at least for
now.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The rxtx2 clock of i.MX6 S/PDIF is currently set to "asrc" clock.
However, according to SoC documentation, rxtx2 is connected to
ASRC_EXT_CLK, a different external clock.
Testing on Cubox-i system seems to confirm that: when fsl_spdif is
forced to select rxtx2 as input clock, audio playback fails with an I/O
error.
Set rxtx2 to the dummy clock by default to prevent fsl_spdif from
selecting it.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Cc: Mark Brown <broonie@kernel.org>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
This patch adds CSI subnodes for IPU1 and IPU2 that will contain
ports and endpoints connecting to external elements in the video
pipeline.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
The new bindings drops one clock, renames the others and
drops the old interrupt mapping.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Add alias for FEC ethernet on i.MX to allow bootloaders (like U-Boot)
patch-in the MAC address for FEC using this alias.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Per bindings of fixed-clock, #clock-cells is a required property. Let's
add it for those fixed rate clocks.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Those two properties should have been set to zero, which
is the same as not specifying them.
Having address-cells set to 1 causes OF interrupt
mapping routines to add 1 to the interrupt-cells
property and as result fail because all calculations
are off by one.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
As defined by the common PCI bindings.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
A large part of the arm-soc patches are nowadays DT changes, adding support
for new SoCs, boards and devices without changing kernel source. The plan
is still to move the devicetree files out of the kernel tree and reduce
the amount of churn going on here, but we keep finding reasons to delay
doing that.
Changes are really all over the place, with little sticking out particularly.
We have contributions from a total of 116 people in this branch.
Unfortunately, the size of this branch also causes a significant number
of conflicts at the moment, typically when subsystem maintainers merge
patches that change the driver at the same time as the dts files. In
most cases this could be avoided because the dts changes are supposed
to be compatible in both ways, and we are asking everyone to send ARM
dts changes through our tree only.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zl/N
-----END PGP SIGNATURE-----
Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
This patch connects IPU and display encoder (HDMI, LVDS, MIPI)
device tree nodes, as well as parallel displays on the DISP0
and DISP1 outputs, using the OF graph bindings described in
Documentation/devicetree/bindings/media/video-interfaces.txt
The IPU ports correspond to the two display interfaces. The
order of endpoints in the ports is arbitrary.
Each encoder with an associated input multiplexer has multiple
input ports in the device tree. The order and reg property of
the ports must correspond to the multiplexer input order.
Since the imx-drm node now only needs to contain links to the
display interfaces, it can be moved to the SoC dtsi level. At
the board level, only connections between the display interface
ports and encoders or panels have to be added.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Extracted from another patch by Fabio Estevam, this adds the DT
configuration for HDMI output on the IMX6 SoCs
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
imx51-ssi and imx21-ssi are different IPs. imx51-ssi supports online
reconfiguration and needs this for correct interaction with SDMA. This
patch adds imx51-ssi before each imx21-ssi for all imx6 SoCs.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
We need to use controller id to access different register regions
for mxs phy.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Shengjiu Wang