To get hundredths of MHz the rate needs to be divided by 10'000.
Here is an example:
twd_timer_rate = 123456789
Before the patch:
twd_timer_rate / 1000000 = 123
(twd_timer_rate / 1000000) % 100 = 23
Result: 123.23MHz.
After being fixed:
twd_timer_rate / 1000000 = 123
(twd_timer_rate / 10000) % 100 = 45
Result: 123.45MHz.
Signed-off-by: Vitaly Kuzmichev <vkuzmichev@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that the twd timer reload value is reprogrammed each time we
enter periodic mode. This ensures that the reload value is always
reset correctly.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Colin Cross <ccross@android.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The fraction of MHz was not being displayed correctly as the calculation
was a factor of 10 out. Fix this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When a CPU is hot unplugged, the generic tick code cleans up the
clock event device, but fails to call down to the device's set_mode
function to actually shut the device down.
To work around this, we've historically had a local_timer_stop()
callback out of the hotplug code. However, this adds needless
complexity when we have the clock event device itself available.
Explicitly call the clock event device's set_mode function with
CLOCK_EVT_MODE_UNUSED, so that the hardware can be cleanly shutdown
without any special external callbacks. When/if the generic code
is fixed, percpu_timer_stop() can be killed off.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid adding nasty genirq-specific code to local timers to enable PPI
interrupts. Instead, provide a gic function to do this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The TWD local timers are unable to wake up the CPU when it is placed
into a low power mode, eg. C3. Therefore, we need to adapt things
such that the TWD code can cope with this.
We do this by always providing a broadcast tick function, and marking
the fact that the TWD local timer will stop in low power modes. This
means that when the CPU is placed into a low power mode, the core
timer code marks this fact, and allows an IPI to be given to the core.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
This moves the TWD register set of MPcore to a common
existing file so that watchdog driver can access it
Signed-off-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since this IRQ descriptor doesn't have an action registered, it is
allowed for probing via probe_irq_on/off() and it will be disabled by
the latter function. This patch sets the IRQ_NOPROBE status bit for the
local timer descriptor.
Signed-off-by: Varun Swara <Varun.Swara@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Fix:
WARNING: vmlinux.o(.text+0x247c): Section mismatch in reference from the function cpu_idle() to the function .cpuexit.text:cpu_die()
The function cpu_idle() references a function in an exit section.
Often the function cpu_die() has valid usage outside the exit section
and the fix is to remove the __cpuexit annotation of cpu_die.
WARNING: vmlinux.o(.cpuexit.text+0x3c): Section mismatch in reference from the function cpu_die() to the function .cpuinit.text:secondary_start_kernel()
The function __cpuexit cpu_die() references
a function __cpuinit secondary_start_kernel().
This is often seen when error handling in the exit function
uses functionality in the init path.
The fix is often to remove the __cpuinit annotation of
secondary_start_kernel() so it may be used outside an init section.
Sam says:
> The annotation of cpu_die() is wrong.
> To be annotated __cpuexit the function shall:
> - be used in exit context and only in exit context with HOTPLUG_CPU=n
> - be used outside exit context with HOTPLUG_CPU=y
So, this also means __cpu_disable(), __cpu_die() and twd_timer_stop() are
also wrong. However, removing __cpuexit from cpu_die() creates:
WARNING: vmlinux.o(.text+0x6834): Section mismatch in reference from the function cpu_die() to the function .cpuinit.text:secondary_start_kernel()
The function cpu_die() references
the function __cpuinit secondary_start_kernel().
This is often because cpu_die lacks a __cpuinit
annotation or the annotation of secondary_start_kernel is wrong.
so fix this using __ref.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Vitaly Kuzmichev