Paul Gortmaker says:
====================
Eric noticed that the handling of local u64 ethtool counters for
this driver commonly found on Freescale ppc-32 boards was racy.
However, before converting them over to atomic64_t, I noticed
that an internal struct was being used to determine the offsets
for exporting this data into the ethtool buffer, and in doing
so, it assumed that the counters would always be u64. Rather
than keep this implicit assumption, a simple code cleanup gets
rid of the struct completely, and leaves less conversion sites.
The alternative solution would have been to take advantage of
the fact that the counters are all relating to error conditions,
and hence make them internally u32. In doing so, we'd be assuming
that U32_MAX of any particular error condition is highly unlikely.
This might have made sense if any increments were in a hot path.
Tested with "ethtool -S eth0" on sbc8548 board.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking at some asm dump for an unrelated change, Eric
noticed in the following stats count increment code:
50b8: 81 3c 01 f8 lwz r9,504(r28)
50bc: 81 5c 01 fc lwz r10,508(r28)
50c0: 31 4a 00 01 addic r10,r10,1
50c4: 7d 29 01 94 addze r9,r9
50c8: 91 3c 01 f8 stw r9,504(r28)
50cc: 91 5c 01 fc stw r10,508(r28)
that a 64 bit counter was used on ppc-32 without sync
and hence the "ethtool -S" output was racy.
Here we convert all the values to use atomic64_t so that
the output will always be consistent.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The gfar_stats struct is only used in copying out data
via ethtool. It is declared as the extra stats, followed
by the rmon stats. However, the rmon stats are never
actually ever used in the driver; instead the rmon data
is a u32 register read that is cast directly into the
ethtool buf.
It seems the only reason rmon is in the struct at all is
to give the offset(s) at which it should be exported into
the ethtool buffer. But note gfar_stats doesn't contain
a gfar_extra_stats as a substruct -- instead it contains
a u64 array of equal element count. This implicitly means
we have two independent declarations of what gfar_extra_stats
really is. Rather than have this duality, we already have
defines which give us the offset directly, and hence do not
need the struct at all.
Further, since we know the extra_stats is unconditionally
always present, we can write it out to the ethtool buf
1st, and then optionally write out the rmon data. There
is no need for two independent loops, both of which are
simply copying out the extra_stats to buf offset zero.
This also helps pave the way towards allowing the extra
stats fields to be converted to atomic64_t values, without
having their types directly influencing the ethtool stats
export code (gfar_fill_stats) that expects to deal with u64.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
The bnx2x gso_type setting bug fix in 'net' conflicted with
changes in 'net-next' that broke the gso_* setting logic
out into a seperate function, which also fixes the bug in
question. Thus, use the 'net-next' version.
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, the MPC5200 FEC ethernet driver relied upon the bootloader
(U-Boot) to write the MAC address into the ethernet controller
registers. The Linux driver should not rely on such a thing. So
lets read the MAC address from the DT as it should be done here.
The following priority is now used to read the MAC address:
1) First, try OF node MAC address, if not present or invalid, then:
2) Read from MAC address registers, if invalid, then:
3) Log a warning message, and choose a random MAC address.
This fixes a problem with a MPC5200 board that uses the SPL U-Boot
version without FEC initialization before Linux booting for
boot speedup.
Additionally a status line is now be printed upon successful
driver probing, also displaying this MAC address.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Santosh Rastapur <santosh@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW switch can act as Dual EMAC by segregating the switch ports
using VLAN and port VLAN as per the TRM description in
14.3.2.10.2 Dual Mac Mode
Following CPSW components will be common for both the interfaces.
* Interrupt source is common for both eth interfaces
* Interrupt pacing is common for both interfaces
* Hardware statistics is common for all the ports
* CPDMA is common for both eth interface
* CPTS is common for both the interface and it should not be enabled on
both the interface as timestamping information doesn't contain port
information.
Constrains
* Reserved VID of One port should not be used in other interface which will
enable switching functionality
* Same VID must not be used in both the interface which will enable switching
functionality
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As CPTS is common module for both EMAC in Dual EMAC mode so making cpts as
pointer.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Introduced parameter to add port number for directed packet in cpdma_chan_submit
* Source port detection macro with DMA descriptor status
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The original fix that was applied for setting gso_type required more change
than necessary because it was assumed ixgbe does RSC on IPv6 frames and this
is not correct. RSC is only supported with IPv4/TCP frames only. As such we
can simplify the fix and avoid the unnecessary move of eth_type_trans.
The previous patch "ixgbe: fix gso type" and this patch reduce the entire fix
to one line that sets gso_type to TCPV4 if the frame is RSC.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Do not read mailbox registers on timeout
o Add a helper function to handle mailbox response
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Handle async events during diagnostic loopback test
o Clear loopback mode on failure to receive async events
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanly separate 83xx diagnostic IRQ test from 82xx
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanly separate 83xx diagnostic loopback test routines from 82xx
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a helper routine to handle async events, as it is being called
from multiple places
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver needs to stop participating in firmware based Inter Driver
Communication (IDC) while unloading driver
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register for firmware based Inter Driver Communication (IDC) using initialize
NIC as the first mailbox command
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In LRO mode, bnx2x set gso_size but not gso type.
This leads to crashes in macvtap.
Commit cbf1de7232
queued for 3.9 includes a more complete fix.
This is a minimal patch to avoid the crash, for 3.8.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlcnic set gso_size but not gso type. This leads to crashes
in macvtap.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe set gso_size but not gso_type. This leads to
crashes in macvtap.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch the stmmac fails in case of the phy device
is not found; w/o this fix the mdio can be register twice when
do down/up the iface and this is not correct.
Reported-by: Stas <stsp@list.ru>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the name of the macro used for
debugging the transmit process. I used STMMAC_TX_DEBUG
instead of STMMAC_XMIT_DEBUG.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert two power saving r8169 changes to fix some regressions
reported.
Reported-by: Jörg Otte <jrg.otte@gmail.com>
Tested-by: Jörg Otte <jrg.otte@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit d64ec84151.
Jörg Otte reported his 8168evl to increase boot time link detection
from 1.6 to 10 s.
Hayes suggests reverting it for the time being.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Jörg Otte <jrg.otte@gmail.com>
Synchronize with 'net' in order to sort out some l2tp, wireless, and
ipv6 GRE fixes that will be built on top of in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This was preventing GRO and RxCheckSum offload to happen.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
For the affected mallocs around these OOM messages:
Converted kmallocs with multiplies to kmalloc_array.
Converted a kmalloc/memcpy to kmemdup.
Removed now unused stack variables.
Removed unnecessary parentheses.
Neatened alignment.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last (bool) parameter in bgmac_cmdcfg_maskset says if the write
should be made, even if value didn't change. Currently driver doesn't
match the specs about (not) forcing some changes. This makes it follow
them.
Reported-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e0c0755779.
Jörg Otte reported his 8168evl to fail boot time link detection.
Hayes suggests reverting it for the time being.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Cc: Jörg Otte <jrg.otte@gmail.com>
This adds check for a valid Ethernet MAC address and in case it is not,
it will generate a valid random one, such that the adapter is still
usable.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Revert iwlwifi reclaimed packet tracking, it causes problems for a
bunch of folks. From Emmanuel Grumbach.
2) Work limiting code in brcmsmac wifi driver can clear tx status
without processing the event. From Arend van Spriel.
3) rtlwifi USB driver processes wrong SKB, fix from Larry Finger.
4) l2tp tunnel delete can race with close, fix from Tom Parkin.
5) pktgen_add_device() failures are not checked at all, fix from Cong
Wang.
6) Fix unintentional removal of carrier off from tun_detach(),
otherwise we confuse userspace, from Michael S. Tsirkin.
7) Don't leak socket reference counts and ubufs in vhost-net driver,
from Jason Wang.
8) vmxnet3 driver gets it's initial carrier state wrong, fix from Neil
Horman.
9) Protect against USB networking devices which spam the host with 0
length frames, from Bjørn Mork.
10) Prevent neighbour overflows in ipv6 for locally destined routes,
from Marcelo Ricardo. This is the best short-term fix for this, a
longer term fix has been implemented in net-next.
11) L2TP uses ipv4 datagram routines in it's ipv6 code, whoops. This
mistake is largely because the ipv6 functions don't even have some
kind of prefix in their names to suggest they are ipv6 specific.
From Tom Parkin.
12) Check SYN packet drops properly in tcp_rcv_fastopen_synack(), from
Yuchung Cheng.
13) Fix races and TX skb freeing bugs in via-rhine's NAPI support, from
Francois Romieu and your's truly.
14) Fix infinite loops and divides by zero in TCP congestion window
handling, from Eric Dumazet, Neal Cardwell, and Ilpo Järvinen.
15) AF_PACKET tx ring handling can leak kernel memory to userspace, fix
from Phil Sutter.
16) Fix error handling in ipv6 GRE tunnel transmit, from Tommi Rantala.
17) Protect XEN netback driver against hostile frontend putting garbage
into the rings, don't leak pages in TX GOP checking, and add proper
resource releasing in error path of xen_netbk_get_requests(). From
Ian Campbell.
18) SCTP authentication keys should be cleared out and released with
kzfree(), from Daniel Borkmann.
19) L2TP is a bit too clever trying to maintain skb->truesize, and ends
up corrupting socket memory accounting to the point where packet
sending is halted indefinitely. Just remove the adjustments
entirely, they aren't really needed. From Eric Dumazet.
20) ATM Iphase driver uses a data type with the same name as the S390
headers, rename to fix the build. From Heiko Carstens.
21) Fix a typo in copying the inner network header offset from one SKB
to another, from Pravin B Shelar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (56 commits)
net: sctp: sctp_endpoint_free: zero out secret key data
net: sctp: sctp_setsockopt_auth_key: use kzfree instead of kfree
atm/iphase: rename fregt_t -> ffreg_t
net: usb: fix regression from FLAG_NOARP code
l2tp: dont play with skb->truesize
net: sctp: sctp_auth_key_put: use kzfree instead of kfree
netback: correct netbk_tx_err to handle wrap around.
xen/netback: free already allocated memory on failure in xen_netbk_get_requests
xen/netback: don't leak pages on failure in xen_netbk_tx_check_gop.
xen/netback: shutdown the ring if it contains garbage.
net: qmi_wwan: add more Huawei devices, including E320
net: cdc_ncm: add another Huawei vendor specific device
ipv6/ip6_gre: fix error case handling in ip6gre_tunnel_xmit()
tcp: fix for zero packets_in_flight was too broad
brcmsmac: rework of mac80211 .flush() callback operation
ssb: unregister gpios before unloading ssb
bcma: unregister gpios before unloading bcma
rtlwifi: Fix scheduling while atomic bug
net: usbnet: fix tx_dropped statistics
tcp: ipv6: Update MIB counters for drops
...
The BCM4785 or sometimes named BMC4705 is a Broadcom SoC which a
Gigabit 5750 Ethernet core. The core is connected via PCI with the rest
of the SoC, but it uses some extension.
This core does not use a firmware or an eeprom.
Some devices only have a switch which supports 100MBit/s, this
currently does not work with this driver.
This patch was original written by Michael Buesch <m@bues.ch> and is in
OpenWrt for some years now.
This was tested on a Linksys WRT610N V1 and older versions of this patch
were tested by other people on different devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In OpenWrt we currently use a switch driver which uses the ioctls to
configure the switch in the phy. We have to provide the phy_id to do
so, but without this patch this is not possible.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
=========================================================
[ INFO: possible irq lock inversion dependency detected ]
3.8.0-rc5+ #82 Not tainted
---------------------------------------------------------
swapper/0/0 just changed the state of lock:
(&(&fep->hw_lock)->rlock){..-...}, at: [<8034e2f8>] fec_enet_start_xmit+0x48/0x 2cc
but this lock took another, SOFTIRQ-unsafe lock in the past:
(prepare_lock){+.+.+.}
and interrupts could create inverse lock ordering between them.
other info that might help us debug this:
Possible interrupt unsafe locking scenario:
CPU0 CPU1
---- ----
lock(prepare_lock);
local_irq_disable()
lock(&(&fep->hw_lock)->rlock);
lock(prepare_lock);
<Interrupt>
lock(&(&fep->hw_lock)->rlock);
*** DEADLOCK ***
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Old method will cause init spinlock twice.
New method will avoid init spinlock twice and fix miss init spinlock
at fec_restart.
BUG: spinlock bad magic on CPU#1, swapper/0/1
lock: 0xbfae0f8c, .magic: 00000000, .owner: <none>/-1, .owner_cpu: 0
Backtrace:
[<80011d54>] (dump_backtrace+0x0/0x10c) from [<804e7800>] (dump_stack+0x18/0x1c)
r6:bfae0000 r5:bfae0f8c r4:00000000 r3:806c1310
[<804e77e8>] (dump_stack+0x0/0x1c) from [<804e9f20>] (spin_dump+0x80/0x94)
[<804e9ea0>] (spin_dump+0x0/0x94) from [<804e9f60>] (spin_bug+0x2c/0x30)
r5:805f6f8c r4:bfae0f8c
[<804e9f34>] (spin_bug+0x0/0x30) from [<80257984>] (do_raw_spin_lock+0x170/0x1b0 )
r5:806b4950 r4:bfae0f8c
[<80257814>] (do_raw_spin_lock+0x0/0x1b0) from [<804ed15c>] (_raw_spin_lock_irqs ave+0x18/0x20)
[<804ed144>] (_raw_spin_lock_irqsave+0x0/0x20) from [<8033c694>] (fec_ptp_start_ cyclecounter+0x3c/0x120)
r4:bfae0f8c r3:00000002
[<8033c658>] (fec_ptp_start_cyclecounter+0x0/0x120) from [<80339e08>] (fec_resta rt+0x56c/0x5f8)
r8:00000000 r7:806e6f48 r6:00000112 r5:806b4950 r4:bfae0000
[<8033989c>] (fec_restart+0x0/0x5f8) from [<8033b9e4>] (fec_probe+0x508/0xa48)
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix issue in Mellanox driver related to BQL. netdev_tx_reset_queue
was not being called in certain situations where the device was
being start and stopped. Moved netdev_tx_reset_queue from the reset
device path to mlx4_en_free_tx_buf which is where the rings are
cleaned in a reset (specifically from device being stopped).
Signed-off-by: Tom Herbert <therbert@google.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai says:
====================
This series from Yan Burman adds support for unicast MAC address filtering and
ndo FDB operations. It also includes some optimizations to loopback related
decisions and checks in the TX/RX fast path and one cleanup, all in separate
patches.
Today, when adding macvlan devices, the NIC goes into promiscuous mode, since
unicast MAC filtering is not supported. With these changes, macvlan devices can
be added without the penalty of promiscuous mode.
If for some reason adding a unicast address filter fails e.g as of missing space in
the HW mac table, the device forces itself into promiscuous mode (and out of this
forced state when enough space is available).
Also, now it is possible to have bridge under multi-function configuration that include
PF and VFs. In order to use bridge over PF/VFs, VM MAC fdb entries must be added e.g.
using 'bridge fdb add' command.
Changes from v1 - based on more comments from Eric Dumazet:
* added failure handling when adding unicast address filter
Changes from v0 - based on comments from Eric Dumazet:
* Removed unneeded synchronize_rcu()
* Use kfree_rcu() instead of synchronize_rcu() + kfree()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for setting embedded switch fdb in case of SRIOV, by
implementing ndo_fdb_{add, del, dump}. This will allow to use
bridged configuration with multi-function. In order to add VM MAC
to the eSwitch fdb, the following command may be used over the relevant function interface:
bridge fdb add <MAC> permanent self dev <IFACE>
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement and advertise unicast MAC filtering, such that setting macvlan
instance over mlx4_en interfaces will not require the networking core
to put mlx4_en devices in promiscuous mode.
If for some reason adding a unicast address filter fails e.g as of missing space in
the HW mac table, the device forces itself into promiscuous mode (and out of this
forced state when enough space is available).
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a preparation step for supporting multiple unicast addresses, store MAC addresses in hash table.
Remove the radix tree for MAC addresses per QP, as it's not in use.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to having more than one unicast MAC per port, we need to keep track
of the previous MAC address in the flow of ndo_set_mac_address,
so that mlx4_en_replace_mac will know what to replace.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mlx4_en_do_set_multicast serves as the ndo_set_rx_mode entry for mlx4_en,
doing all related work. Split it to few calls, one per required functionality
(e.g multicast, promiscuous, etc) and rename some structures and calls
to use rx_mode notation instead of multicast.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move low level code that deals with management of Ethernet MACs and QPs from mlx4_core to mlx4_en.
Also convert the new functions to deal with MACs in form of char array instead of u64.
Actual functions moved:
mlx4_replace_mac
mlx4_get_eth_qp
mlx4_put_eth_qp
To conduct this change, some functionality had to be exported from the core,
the following functions were added:
mlx4_get_base_qp
__mlx4_replace_mac (low level function for CX1/A0 compatibility)
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code consistent in regard to error messages
not spanning multiple lines.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, RX path code that does RX filtering is not optimized
and does an expensive conversion. In order to use ether_addr_equal_64bits
which is optimized for such cases, we need the MAC address kept by the device
to be in the form of unsigned char array instead of u64. Store the MAC address
as unsigned char array and convert to/from u64 out of the fast path when needed.
Side effect of this is that we no longer need priv->mac, since it's the same
as dev->dev_addr.
This optimization was suggested by Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there are relatively complex conditional checks in the fast path,
for TX loopback enabling and resulting RX filter logic.
Move elaborate if's out of data path, replace them with a single flag
for each state and update that state from appropriate places.
Also, in native (non SRIOV) mode and not in loopback or in selftest,
there is no need to try and filter out packets that HW loopback-ed,
as in native mode we do not loopback packets anymore.
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix mlx4 VFs not working on old guests because of 64B CQE changes
- Fix ill-considered sparse fix for qib
- Fix IPoIB crash due to skb double destruct introduced in 3.8-rc1
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=bmKU
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull IB regression fixes from Roland Dreier:
- Fix mlx4 VFs not working on old guests because of 64B CQE changes
- Fix ill-considered sparse fix for qib
- Fix IPoIB crash due to skb double destruct introduced in 3.8-rc1
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/qib: Fix for broken sparse warning fix
mlx4_core: Fix advertisement of wrong PF context behaviour
IPoIB: Fix crash due to skb double destruct
When changing the device from or to promisc mode this only affects the
device after the device is bought up the next time. For bridging it is
needed to change the device to promisc mode while it is up, which is
possible with this patch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic implementation just changes the netdev struct and does not
write the new mac address to the hardware or issues some command to do
so.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
adding support for VLAN interface for cpsw.
CPSW VLAN Capability
* Can filter VLAN packets in Hardware
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add helper functions for VLAN ALE implementations for Add, Delete
Dump VLAN related ALE entries
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commits 9d11bd159
("wimax: Remove unnecessary alloc/OOM messages, alloc cleanups")
and b2adaca92
("ethernet: Remove unnecessary alloc/OOM messages, alloc cleanups")
added a couple of unused variable warnings.
Remove the now unused variables.
Noticed-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to e1000e and ixgbe. Majority of the patches
are against e1000e, where Bruce makes several cosmetic #define moves into
header files. In addition, Bruce does a cleanup of braces to resolve
checkpatch warnings (when using the strict option).
Ixgbe patches contain several fixes as well as updating the copyright. The
fixes from Josh Hay, resolved a possible NULL pointer dereference and
resolved Smatch warnings by fixing return values and memcpy parameters.
Alex provides 2 fixes, the first is to replace rmb() with
read_barrier_depends() in the Tx cleanup. The second fixes an MTU
warning when using SR-IOV which corrects the fact that we were using 1522
to test for the max frame size in ixgbe_change_mtu and 1518 in
ixgbe_set_vf_lpe. The difference was the addition of VLAN_HLEN, which we
only need to add in the case of computing a buffer size, but not a filter
size. Lastly, a patch from Emil which is based on a community patch from
Aurélien Guillaume which adds functions needed for reading SFF-8472
diagnostic data from SFP modules.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/ethtool.c
drivers/net/vmxnet3/vmxnet3_drv.c
drivers/net/wireless/iwlwifi/dvm/tx.c
net/ipv6/route.c
The ipv6 route.c conflict is simple, just ignore the 'net' side change
as we fixed the same problem in 'net-next' by eliminating cached
neighbours from ipv6 routes.
The e1000e conflict is an addition of a new statistic in the ethtool
code, trivial.
The vmxnet3 conflict is about one change in 'net' removing a guarding
conditional, whilst in 'net-next' we had a netdev_info() conversion.
The iwlwifi conflict is dealing with a WARN_ON() conversion in
'net-next' vs. a revert happening in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 08ff32352d ("mlx4: 64-byte CQE/EQE support") introduced a
regression where older guest VF drivers failed to load even when
64-byte EQEs/CQEs are disabled, since the PF wrongly advertises the
new context behaviour anyway. The failure looks like:
mlx4_core 0000:00:07.0: Unknown pf context behaviour
mlx4_core 0000:00:07.0: Failed to obtain slave caps
mlx4_core: probe of 0000:00:07.0 failed with error -38
Fix this by basing this advertisement on dev->caps.flags, which is the
operational capabilities used by the QUERY_FUNC_CAP command wrapper
(dev_cap->flags holds the firmware capabilities).
Reported-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
This change corrects the fact that we were using 1522 to test for the
max frame size in ixgbe_change_mtu and 1518 in ixgbe_set_vf_lpe. The
difference was the addition of VLAN_HLEN which we only need to add in the case
of computing a buffer size, but not a filter size.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rmb in the Tx cleanup path is a much stronger barrier than we really need.
All that is really needed is a read_barrier_depends since the location of the
EOP descriptor is dependent on the eop_desc value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes the rval variable returns from function and replaces
them with direct returns in ixgbe_dcbnl_getnumtcs. It also changes how
ixgbe_gstrings_test is copied into data with memcpy in ixgbe_get_strings
because "*ixgbe_gstrings_test too small (32 vs 160)".
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a default case which goes to the next loop iteration
in the case where p is not set, preventing p from being dereferenced.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds functions needed for reading SFF-8472 diagnostic data
from SFP modules.
Based on original patch from Aurélien Guillaume <footplus@gmail.com>
CC: Aurélien Guillaume <footplus@gmail.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Resolve the following strict checkpatch checks:
CHECK:BRACES: Blank lines aren't necessary after an open brace '{'
CHECK:BRACES: Blank lines aren't necessary before a close brace '}'
CHECK:BRACES: braces {} should be used on all arms of this statement
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There are enough register offsets to warrant being in their own header
file, and doing so logically separates them from other header file content.
They have been converted from an enumerated data type to #defines as is
done in all the other Intel wired ethernet drivers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move #defines, function prototypes and data types which are applicable to
all/most devices supported by the driver but are specific to the
manageability component of each device to the new manage.h header file.
These #defines, function prototypes and data types can be used by other
files in the driver and moving them to the manageability-specific file
makes it clearer to which component they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move #defines and function prototypes which are applicable to all/most
devices supported by the driver and are specific to the NVM component of
each device to the new nvm.h header file. These #defines and function
prototypes can be used by other files in the driver and moving them to the
NVM-specific file makes it clearer to which component they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move #defines and function prototypes which are applicable to all/most
devices supported by the driver and are specific to the PHY component of
each device to the new phy.h header file. These function prototypes can be
used by other files in the driver and moving them to the PHY-specific file
makes it clearer to which component they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move prototypes for functions which are applicable to all/most devices
supported by the driver and are specific to the MAC component of each
device to the new mac.h header file. These function prototypes can be used
by other files in the driver and moving them to the MAC-specific file makes
it clearer to which component they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move #defines and function prototypes specific to the ICH/PCH family of
devices (ICH8/82562, ICH8/82566, ICH8/82567, ICH9/82562, ICH9/82566,
ICH9/82567, ICH10/82567, 82577, 82578, 82579, I217, I218) to the new
ich8lan.h header file (the convention for Intel wired ethernet drivers is
to use the name of the first device in the family for related file and
function names). These defines and function prototypes can be used by
other files in the driver and moving them to the ICH/PCH-family-specific
file makes it clearer to which devices they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move #defines specific to the ESB2/82563 family of devices to the new
80003es2lan.h header file. These defines can be used by other files in the
driver and moving them to the 80003es2lan-family-specific file makes it
clearer to which devices they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move #defines and function prototypes specific to the 8257x family of
devices (82571, 82572, 82573, 82574, 82583) to the new 82571.h header file
(the convention for Intel wired ethernet drivers is to use the name of the
first device in the family for related file and function names). These
defines and function prototypes can be used by other files in the driver
and moving them to the 8257x-family-specific file makes it clearer to which
devices they are applicable.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We recently refactored the driver source, this patch will take care of
updating copyright date and adding it to newly added files.
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ee873fda3b
"gianfar: Pack struct gfar_priv_grp into three cachelines"
causes the following null dereference at driver init on sbc8548:
libphy: Freescale PowerQUICC MII Bus: probed
Unable to handle kernel paging request for data at address 0x00000000
Faulting instruction address: 0xc01d6a38
Oops: Kernel access of bad area, sig: 11 [#1]
[...]
NIP [c01d6a38] gfar_parse_group+0x228/0x280
LR [c01d6a34] gfar_parse_group+0x224/0x280
Call Trace:
[ef82dd60] [c01d6a34] gfar_parse_group+0x224/0x280 (unreliable)
[ef82dd90] [c01d73a4] gfar_probe+0x284/0xfe0
The reason is that the commit also changed the allocation of the
Rx and error handling irq structs to be skipped for !MQ_MG_MODE.
In the !MQ_MG_MODE case, only the Tx irq struct is allocated.
Digging further, we see that MQ_MG_MODE is set only if we find
the OF compatible string "fsl,etsec2".
A quick grep in the dts directory shows lots of boards that support
Rx/Tx/Err, but without this specific compat string. And hence they
go after the unallocated Rx/Error structs and cause the above oops.
Hence such a change can not be deployed until all the dts files
are updated and sufficiently deployed. Further, the optimization
is of limited value, since the kmalloc'd struct in question has only
a single unsigned int, and an (IFNAMSIZ + 6) sized string.
Note that no changes to the freeing code are needed here, as it
already did an unconditional free of Rx/Tx/Error gfar_irqinfo.
Cc: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_eth_mc_map function can't be used when CONFIG_INET isn't defined.
Fixed compilation error by adding CONFIG_INET define check before using the
function.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate return value of mlx4_en_ethtool_add_mac_rule_by_ipv4 in case of
failure.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when the PF driver is unloaded and re-loaded while VFs are attached
to VMs, it loses control of its VFs.
The PF driver now uses the newly defined/created GET_IFACE_LIST cmd
(available in FW ver >= 4.6) to query the if_id of the VFs
(enabled in its previous life). The PF driver then uses the if_id for
further VF configuration.
The GET_IFACE_MAC_LIST cmd has also implemented in BE3 FW for PF to
query pmac-ids used by its VFs.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If stmmac_dvr_probe() fails in stmmac_pci_probe(), it breaks off initialization,
deallocates all resources, but returns zero.
The patch adds -ENODEV as return value in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
We actually store the MAC address as well as the board_name here. The
longest board_name is 75 characters so there is more than enough room
to hold the 17 character MAC and the ": " divider. But making this
buffer larger silences a static checker warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-By: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the interface does not have carrier but when it's put into
loopback mode (for tests), it does not make sense to not have
the carrier. So force it!
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) rhine_tx() should use dev_kfree_skb() not dev_kfree_skb_irq()
2) rhine_slow_event_task's NAPI triggering logic is racey, it
should just hit the interrupt mask register. This is the
same as commit 7dbb491878
("r8169: avoid NAPI scheduling delay.") made to fix the same
problem in the r8169 driver. From Francois Romieu.
Reported-by: Jamie Gloudon <jamie.gloudon@gmail.com>
Tested-by: Jamie Gloudon <jamie.gloudon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For standard IEEE MII-compatible transceivers, the kernel has generic
register and bit definitions. Use those instead of redundant local
defines.
Do not replace references of MII_CR_SPEED_10 with BMCR_SPEED10 (0x0000)
when it is not necessary (i.e. when it is bitwise OR'ed with another
value).
Some whitespace issues in the surrounding context of the above changes are
also cleaned up.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the unused parameter when possible, otherwise use __always_unused
attribute.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For clarity, wrap OR'ed bit settings with parentheses.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove redundant defines which are defined elsewhere.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Removes the autoneg parameter from the setup_link functions.
Adds local variable autoneg to setup_link functions to be passed
to get_link_capabilities functions if needed.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Removes the autoneg parameter from the setup_link_speed functions. These
functions do nothing with this parameter.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Renames some autoneg/speed variables to be more consistent with check_link,
get_link_capabilities, and setup_link function calls. Initializes instances
of autoneg.
Signed-off-by: Josh Hay <joshua.a.hay@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The device lookup neglected to do a pci_dev_put() to decrement the
device reference count.
Reported-by: Elena Gurevich <elena.gurevich@toganetworks.com>
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for up2tc change and call ixgbe_dcbnl_devreset() if the mapping has
changed but the number of TC's in use has not changed.
Signed-off-by: Amir Hanania <amir.hanania@intel.com>
Tested-by: Jack Morgan <jack.morgan@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Under heavy CPU load, changing, ring size/mtu/etc. could result in transmit
timeout, since stop-start port might take more than 10 seconds.
Calling netif_detach_device to prevent tx queue transmit timeout.
netif_detach_device() is not called under ndo_stop, because netif_carrier_off
will prevent the timeout, and device should not be marked as not present, or
else user won't be able to start it later on.
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mac reassignments should only be done when not supported by the firmware. To
accomplish that, checking firmware capability bit to know whether we should
reassign macs in the driver.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Firmware dynamically changes flow steering hash configuration from covering
L2 only to "full" L2/L3/L4 mode needed. The dynamic change allows the driver
to set hard coded hash configuration which is changed by the firmware from L2
to L2/L3/L4 when attaching the first L3/L4 flow steering rule and back to L2
when there are no more such rules.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the driver unload flow, all steering rules must be deleted,
make sure to remove the rules that were set through ethtool.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Attaching steering rules while the interface is down is an invalid operation, block it.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan mask field should be validated and assigned according to the field
size which is 12 bits. Also replace the numeric 0xfff mask with existing kernel
macro.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When attaching flow steering rules via Ethtool accept only valid vlans IDs e.g
in the range: [0,4095].
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Destination mac is a mandatory specification for ip/udp steering rules.
When attaching multicast steering rules via ethtool the unicast mac of the
interface was added to the rule specification instead of the multicast mac.
The following commit sets the corresponding multicast mac for the rule multicast ip.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The allow_loopback flag was wrongly set using arithmetic bit operation, change
the code to use logical bit operation.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the fields for struct mlx4_net_trans_rule_hw_ctrl were packed into u32
and accessed through bit field operations. Expose and access them directly as
u8.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o ipv4 address was not getting programmed properly because of
improper byte order conversion
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish chopra <manish.chopra@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions. Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors. Correctable errors will be handled
by the hardware. Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded. If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error. The driver will then reset the hardware in order to
clear the error and restart.
Both types of errors will be accounted for in statistics counters.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: <stable@vger.kernel.org> # 3.5.x & 3.6.x
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring in the 'net' tree so that we can get some ipv4/ipv6 bug
fixes that some net-next work will build upon.
Signed-off-by: David S. Miller <davem@davemloft.net>
* remove unused members(!): imask, ievent
* move space consuming interrupt name strings (int_name_* members) to
external structures, unessential for the driver's hot path
* keep high priority hot path data within the first 2 cache lines
This reduces struct gfar_priv_grp from 6 to 3 cache lines.
(Also fixed checkpatch warnings for the old code, in the process.)
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor out redundant code (improve readability, source code size).
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resize and regroup structure members to eliminate memory holes and
to pack the structure into 2 cache lines (from 3).
tx_ring_size was resized from 4 to 2 bytes and few members were re-grouped
in order to eliminate byte holes and achieve compactness.
Where possible, few members were grouped according to their usage and access
order (i.e. start_xmit vs. clean_tx_ring members), less important members
were pushed at the end.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup the format of ethoc.c to meet network driver style as
per checkpatch.pl.
Signed-off-by: Barry Grussling <barry@grussling.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
just as it should have been. It also helps
removing the, now unnecessary, workqueue.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The file uses nothing from the version.h header, so there is no reason
to include it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Switch to use ndo_get_stats64 to get 64bit statistics.
Signed-off-by: Jamie Gloudon <jamie.gloudon@gmail.com>
Tested-by: Jamie Gloudon <jamie.gloudon@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
This series contains updates to e1000e, ixgbevf, igb and igbvf.
Majority of the patches are code cleanups of e1000e where code
is removed (Yeah!). The other two e1000e patches are fixes. The
first is to fix the maximum frame size for 82579 devices. The second
fix is to resolve an issue with devices other than 82579 that suffer
from dropped transactions on platforms with deep C-states when
jumbo frames are enabled.
The ixgbevf patch is to ensure that the driver fetches the correct,
refreshed value for link status and speed when the values have changed.
The igb and igbvf patches are a solution to an issue Stefan Assmann
reported, where when the PF is up and igbvf is loaded, the MAC address
is not generated using eth_hw_addr_random().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Tighten up some of the code surrounding MAC addresses. Since the PF is
now giving all zeros instead of a random address, check for this case
and generate a random address. This ensures that we always know when we
have a random address and udev won't get upset about it.
Additionally, tighten up some of the log messages and clean up the
formatting.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If the user has not assigned a MAC address to a VM, then don't give it a
random one. Instead, just give it zeros and let it figure out what to do
with them.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A recent change makes it necessary to set get_link_status to ensure that
the driver fetches the correct, refreshed value for link status and speed
when it has changed in the physical function device.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Code was removed but the applicable comments were not.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unnecessary #include, forward prototype of struct e1000_adapter and
an empty comment; fix a comment which mentions "static data for the MAC"
which is not applicable to the following struct; and cleanup some
whitespace issues.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All references to E1000_ERT_2048 have been removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It has been found that devices other than 82579 (a.k.a. e1000_pch2lan)
suffer from dropped transactions on platforms with deep C-states when
jumbo frames are enabled. For example, LOMs on ICH9- and ICH10-based
platforms which recently had early-receive de-featured (for stability
reasons) suffer from this. To resolve this for all devices, when jumbo
frames are enabled set the PM QoS DMA latency request based on the size
of the receive packet buffer less one full frame.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The largest jumbo frame supported by the 82579 hardware is 9018.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function e1000e_commit_phy() and replace the few calls to it
with the same function pointer that it would call. The function pointer is
almost always set for the devices that access these code paths so there is
no risk of a NULL pointer dereference; for the few instances where the
function pointer might not be set (i.e. can be called for the few devices
which do not have this function pointer set), check for a valid function
pointer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function e1000_get_cable_length() and replace the two calls
to it with the same function pointer that it would call.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function e1000_get_phy_cfg_done() and replace the single call
to it with the same function pointer that it would call. The function
pointer is always set so there is no risk of a NULL pointer dereference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In keeping with the e1000e driver function naming convention, the subject
function is renamed to indicate it is generic, i.e. it is applicable to
more than just a single MAC family (e.g. 80003es2lan, 82571, ich8lan).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove the function e1000_force_speed_duplex() and replace the single call
to it with the same function pointer that it would call. The function
pointer is always set so there is no risk of a NULL pointer dereference.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace the function e1000_set_d0_lplu_state() with the contents of it
coded in place of the single call to the function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
filters_lock might have been used while it was re-initialized.
Moved filters_lock and filters_list initialization to init_netdev instead of
alloc_resources which is called every time the device is configured.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a possible race where the TX completion handler can clean the
entire TX queue between the decision that the queue is full and actually
closing it. To avoid this situation, check again if the queue is really
full, if not, reopen the transmit and continue with sending the packet.
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Returning 0 (success) when in fact we are aborting the load, leads to kernel
panic when unloading the module. Fix that by returning the actual error code.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device multicast list is protected by netif_addr_lock_bh in the networking core, we should
use this locking practice in mlx4_en too.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Reviewed-by: Yevgeny Petrilin <yevgenyp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port is stopped and flow steering mode is not device managed: promisc QP
rule wasn't removed from MCG table.
Added code to remove it in all flow steering modes.
In addition, promsic rule removal should be in stop port and not in start
port - moved it accordingly.
Signed-off-by: Aviad Yehezkel <aviadye@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Performing the DUMP_ETH_STATS firmware command outside the lock leads to kernel
panic when data structures such as RX/TX rings are freed in parallel, e.g when
one changes the mtu or ring sizes.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Control of receive descriptor must not be returned to ethernet chipset
before vlan tag processing is done.
VLAN tag receive word is now reset both in normal and error path.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Spotted-by: Timo Teras <timo.teras@iki.fi>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static analysis with cppcheck has shown a few instances of a variable
being reassigned a value before the old one has been used. None of these
ever require the old value to be used so remove the old values.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Static analysis with cppcheck has shown a few instances of a variable which
is assigned a value that is never used. A number of these are the return
status of various driver function calls which should be passed back to the
caller of the current function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
...and cleanup some whitespace in other prototypes.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The e1000e driver has been converted to use extended descriptors instead of
the older legacy descriptor type.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Toggling the LANPHYPC Value bit cycles the power on the PHY and sets it
back to power-on defaults. This includes setting it's MAC-PHY messaging
mode to use the PCIe-like interconnect, so the MAC must also be set back
from SMBus mode to PCIe mode otherwise the PHY can be inaccessible.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The largest jumbo frame supported by the i217 and i218 hardware is 9018.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As done with the previous generation managed 82579, prevent the PHY from
being put into an unknown state by blocking the hardware from automatically
configuring the PHY as done with the previous generation managed 82579.
Instead, the driver should configure the PHY with contents of the EEPROM
image.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In rare instances, memory errors have been detected in the internal packet
buffer memory on I217/I218 when stressed under certain environmental
conditions. Enable Error Correcting Code (ECC) in hardware to catch both
correctable and uncorrectable errors. Correctable errors will be handled
by the hardware. Uncorrectable errors in the packet buffer will cause the
packet to be received with an error indication in the buffer descriptor
causing the packet to be discarded. If the uncorrectable error is in the
descriptor itself, the hardware will stop and interrupt the driver
indicating the error. The driver will then reset the hardware in order to
clear the error and restart.
Both types of errors will be accounted for in statistics counters.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add PTP IEEE-1588 support and make accesible via the PHC subsystem.
v2: make e1000e_ptp_clock_info a static const struct per Stephen Hemminger
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Reviewed-by: Jacob Keller <Jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The previous static flow-control thresholds were causing unnecessary pause
packets to be transmitted when jumbo frames are configured reducing the
throughput.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The SHRAH[9] register on I217 has a different R/W bit-mask than RAR and
SHRAL/H registers. Set R/W bit-mask appropriately for SHRAH[9] when
testing the R/W ability of the register. Also, fix the error message log
format so that it does not provide misleading information (i.e. the logged
register address could be incorrect).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Providing communication channel between KVM and e-Switch so that it
can be informed when hypervisor configures a MAC address and VLAN.
qlcnic_mac_learn module param usage will be changed to:
0 = MAC learning is disable
1 = Driver learning is enable
2 = FDB learning is enable
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide port number in command payload for LED/Beaconing tests.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Some adapter types do not support co-existence of Legacy Interrupt with
MSI-x or MSI among multiple functions. For those adapters, prevent attaching
to a function during normal load, if MSI-x or MSI vectors are not available.
o Using module parameters use_msi=0 and use_msi_x=0, driver can be loaded in
legacy mode for all functions in the adapter.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o This patch enables RSS for TYPE-C packets to enable RSS for TCP over IPv6
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The X540 can link at 100Mbps - fix the link speed indicator message to
show that value.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ixgbe claims it supports 64 VFs in its SRIOV capability
structure, but the driver only supports 63. Adjust it
so sysfs sriov configuration checking will check with
the proper totalvf value.
Signed-off-by: Donald Dutile <ddutile@redhat.com>
Acked-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement callbacks in the driver for the new PCI bus driver
interface that allows the user to enable/disable SR-IOV VFs
in a device via the sysfs interface.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for enable/disable of SR-IOV via the PCI sysfs interface
move some core SR-IOV enablement code that would be common to module
parameter usage or callback from the PCI bus driver to a separate
function so that it can be used by either method.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is no actual dependency on initialization of the mailbox ops on
whether SR-IOV is enabled or not and it doesn't hurt to go ahead and
initialize ops unconditionally. Move the initialization into the device
probe so that the mailbox ops are initialized at the time we have the
board info necessary to do it.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
CC: Don Dutile <ddutile@redhat.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Sibai Li <Sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies ixgbe_debugfs.c and the Makefile for the ixgbe
driver to only compile the file when the config is enabled. This means
we can remove the #ifdef inside the ixgbe_debugfs.c file.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to inline the Rx PTP descriptor handling. The main
motivation is to avoid unnecessary jumps into function calls that we then
immediately exit because we are not performing timestamps.
The net result of this change is that ixgbe_ptp_rx_tstamp drops from .5% CPU
utilization in my performance runs to 0%, and the only value tested is the Rx
descriptor which should already be warm in the cache if not stored in a
register.
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects a bug introduced by commit f3444d8b. The rxmtrl value for
the UDP port to timestamp on was moved above the switch statement, but was
overwritten to 0 if the ioctl selected one of the V1 filters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds warnings when a reset of the adapter is scheduled so that the
user can see log of why the reset occurred.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch copies the igb implementation of Tx timestamps, which uses a work
item to poll for the Tx timestamp. In addition it adds a timeout value of 15
seconds, after which it will stop polling.
This is necessary due to an issue with the descriptor being marked done before
the Tx timestamp event has occurred. These two events don't correlate, so using
the done bit on the descriptor as indication that the timestamp must already
have been taken leads to potentially dropped Tx timestamps (especially under
heavy packet load)
Reported-by: Matthew Vick <matthew.vick@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch removes ixgbe_ptp_match, and the corresponding packet filtering from
ixgbe driver. This code was previously causing some issues within the hotpath of
the driver. However the code also provided a check against possible frozen Rx
timestamp due to dropped packets when the Rx ring is full. This patch provides a
replacement solution based on the watchdog.
To this end, whenever a packet consumes the Rx timestamp it stores the jiffy
value in the rx_ring structure. Watchdog updates its own jiffy timer whenever
there is no valid timestamp in the registers.
If watchdog detects a valid timestamp in the registers, (meaning that no Rx
packet has consumed it yet) it will check which time is most recent, the last
time in the watchdog, or any time in the rx_rings. If the most recent "event"
was more than 5seconds ago, it will flush the Rx timestamp and print a warning
message to the syslog.
Reported-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the comment on ptp_overflow_check to match up with what is
currently used as the parameters. Also change the jiffies check to use
time_is_after_jiffies macro.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch updates the filters for ethtool's get_ts_info to return support for
all filters which can be supported by upscaling to ptp_v2_event. The intent
behind this change is due to reasoning that we do in fact support the
filters. (hwtstamp_ioctl returns success after setting the filter to the
upscaled version). In this way we can remain consistent over which filters are
supported via the get_ts_info ioctl and which filters are in practice actually
supported.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch cleans up the ethtool diagnostics test by ensuring that the tests
work properly regardless of what state the adapter was in. The SRIOV VF check is
done at the beginning, forgoing the link test. The if_running -> dev_close is
moved before the link test, as well as a call to enable the Tx laser. This
ensures that the link test will return valid results even when adapter was
previously down. Also, a call to disable the Tx laser is added if the device
was down before the start. This ensures consistent behavior of the Tx laser
before and after the diagnostic checks. The end result is consistent behavior
regardless of device state.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When posting a message on the bulletin board, the PF calculates crc
over the message and places the result in the message. When the VF
samples the Bulletin Board it copies the message aside and validates
this crc. The length of the message is crucial here and must be the
same in both parties. Since the PF is running in the Hypervisor and
the VF is running in a Vm, they can possibly be of different versions.
As the Bulletin Board is designed to grow forward in future versions,
in the VF the length must not be the size of the message structure
but instead it should be a field in the message itself.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 823e1d9 caused bnx2x to fail once BNX2X_STOP_ON_ERROR is set.
Fixes compilation by moving function declarations between header files.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In INTA mode, cnic and bnx2x share the same IRQ. During chip reset,
for example, cnic will stop servicing IRQs after it has shutdown the
cnic hardware resources. However, the shared IRQ is still active as
bnx2x needs to finish the reset. There is a window when bnx2x does
not know that cnic is no longer handling IRQ and things don't always
work properly.
Add a flag to tell bnx2x that cnic is handling IRQ. The flag is set
before the first cnic IRQ is expected and cleared when no more cnic
IRQs are expected, so there should be no race conditions.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix an incorrect SR-IOV memory release which was committed in 1ab4434.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove most of the sparse warnings in the bnx2x compilation
(i.e., thus resulting when compiling with `C=2 CF=-D__CHECK_ENDIAN__').
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't unload the bnx2x driver if its in a recovery process, or if
the previous load have failed.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 15192a8cf there have been a memory leak upon rmmod
of the bnx2x driver.
This corrects the memory leak and corrects the zeroing of internal
memories upon driver load.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing 57712_VF and 57800_VF to CHIP_IS_E2 and CHIP_IS_E3
macros (missing from commit 8395be5).
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add/Revise several debug prints in the bnx2x driver - on regular flows
as well as error flows.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the incorrect usage of `usleep_range(1000, 1000)' into
`usleep_range(1000, 2000)'.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slightly changes the bnx2x code without `true' functional changes.
Changes include:
1. Gathering macros into a single macro when combination is used multiple
times.
2. Exporting parts of functions into their own functions.
3. Return values after if-else instead of only on the else condition
(where current flow would simply return same value later in the code)
4. Removing some unnecessary code (either dead-code or incorrect conditions)
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mostly corrects white spaces, indentations, and comments.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reactivate promiscuous mode in H/W upon gfar_init_mac(), if the
net dev requires it (IFF_PROMISC flag set).
This way the promisc mode is preserved accross device reset conditions
like tx timeout, device restore, a.s.o.
Signed-off-by: Voncken C Acksys <cedric.voncken@acksys.fr>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was introduced in commit 6dccd16 "r8169: merge with version
6.001.00 of Realtek's r8169 driver". I did not find the version
6.001.00 online, but in 6.002.00 or any later r8169 from Realtek
this hunk is no longer present.
Also commit 05af214 "r8169: fix Ethernet Hangup for RTL8110SC
rev d" claims to have fixed this issue otherwise.
The magic compare mask of 0xfffe000 is dubious as it masks
parts of the Reserved part, and parts of the VLAN tag. But this
does not make much sense as the VLAN tag parts are perfectly
valid there. In matter of fact this seems to be triggered with
any VLAN tagged packet as RxVlanTag bit is matched. I would
suspect 0xfffe0000 was intended to test reserved part only.
Finally, this hunk is evil as it can cause more packets to be
handled than what was NAPI quota causing net/core/dev.c:
net_rx_action(): WARN_ON_ONCE(work > weight) to trigger, and
mess up the NAPI state causing device to hang.
As result, any system using VLANs and having high receive
traffic (so that NAPI poll budget limits rtl_rx) would result
in device hang.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Acked-by: David S. Miller <davem@davemloft.net>
CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Christoph Paasch found netxen could trigger a BUG in its dismantle
phase, in netxen_release_tx_buffer(), using full size TSO packets.
cmd_buf->frag_count includes the skb->data part, so the loop must
start at index 1 instead of 0, or else we can make an out
of bound access to cmd_buff->frag_array[MAX_SKB_FRAGS + 2]
Christoph provided the fixes in netxen_map_tx_skb() function.
In case of a dma mapping error, its better to clear the dma fields
so that we don't try to unmap them again in netxen_release_tx_buffer()
Reported-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Cc: Sony Chacko <sony.chacko@qlogic.com>
Cc: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Christoph Paasch <christoph.paasch@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last update to the Ethernet HowTo (over 10 years ago) listed this:
------------------------
SEEQ 8005
Status: Obsolete, Driver Name: seeq8005
There is little information about the card included in the driver,
and hence little information to be put here. If you have a question,
you are probably best trying to e-mail the driver author as listed
in the source.
It was marked obsolete as of the 2.4 series kernels.
------------------------
If it was obsolete over a decade ago, the situation can not have
improved with the passage of time, so let us act on that. Even with
today's improved search engines, I was unable to locate any real
meaningful information on the ISA implementation of this rare chip.
There are ARM and SGI variants of the driver in tree, but they do
not depend on the original x86 driver source or header file. We
leave those non-x86 drivers to be deleted by the arch maintainers
when they decide to expire those legacy platforms as a whole.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is another one that makes sense to target for obsolescence, since
it (a)appeared pre-1995, and (b)was rather rare, and (c)did not
really have any statistically significant active linux user base.
Removing this ISA 10Mbit driver support is unlikely to be even noticed
by the user base of 3.9+ linux kernels, especially when the documentation
clearly indicates the vintage with this text:
"...designed to work with all kernels > 1.1.33"
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These are old ISA 10Mbit cards from the 1st 1/2 of the 1990s and
required manual jumper settings in order to configure them. Here
we remove them on the premise that they are no longer used in any
modern 3.9+ kernels.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is an area I know all too well, after being author of several 8390
drivers, and maintainer of all 8390 drivers during a large part of their
active lifecycle.
To that end, I can say this with a reasonable degree of confidence.
The drivers deleted here represent the earliest (as in early 1990)
hardware and/or rare hardware. The remaining hardware not deleted
here is the more modern/sane of the lot, with ISA-PnP and jumperless
"soft configuration" like the wd and smc cards had.
The original ne2000 driver (ne.c) gets a pass at this time since
AT/LANTIC based cards that could be both ne2000 or wd-like (with
shared memory) and with jumperless configuration were made in the
mid to late 1990's, and performed reasonably well for their era.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This is another driver for relatively rare 10Mbit hardware that
originated in the early 1990's. So we select it for removal at
this point in time as well.
Cc: Mika Kuoppala <miku@iki.fi>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These Fujitsu MB86965 based ISA 10Mbit cards were another of the
relatively rare cards dating from the early 1990s that for one reason
or another didn't seem to get a lot of use in linux. So we retire it
now with a reasonable degree of confidence that it won't impact anyone.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These cards were only available in 8bit format, and in addition
they only had AUI and BNC(10-Base2) interfaces (i.e. no RJ-45).
In fact, they are so rare, that an internet search on these old
cards almost comes up empty, unless the "Micom interlan" name
is used.
This puts them in the equivalent domain as the 3c501, so there
should be no strong opposition to the driver removal, as nobody
is seriously using 3.9+ with 8 bit ISA hardware.
In doing so, the whole "ethernet/racal" category becomes empty,
so we clean up the Makefile/Kconfig and subdir appropriately.
Cc: Andreas Mohr <andi@lisas.de>
Cc: Jan-Pascal van Best <janpascal@vanbest.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Like the other drivers that were in the ISA i825xx family, the ni52
was rather rare, not widely used, and hence perhaps not as reliable
as the more mainstream ISA drivers that were heavily used. Given
that, it is chosen for retirement at this time as well.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This driver supported early to mid 1990's Zenith laptops, of the
2" thick variety. The driver was already dead 10+ years ago, but
we see this in the source:
----------------
/* 10/2002
[...]
Tested on a vintage Zenith Z-Note 433Lnp+. Probably broken on
anything else. Testers (and detailed bug reports) are welcome :-).
----------------
To clarify, a 433 translates into a 486 at 33MHz, and a system with
a default of 4MB RAM. I can't fault the noble effort to keep things
working a decade ago, but at this point in time, there is no valid
justification to continue carrying this driver along.
Note that there is no associated Space.c cleanup here since this
driver was using module_init to hook itself in.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
These old drivers should not be confused with the very common PCI
cards that are supported by e100.c -- these older 10Mbit ISA only
drivers were not as commonly used as some of the other ISA drivers,
simply due to hardware availability and pricing.
Given the rarity of the hardware, and the subsequent less extensive
use of the drivers, it makes sense to obsolete them at this point
in time, along with other rare/experimental ISA drivers.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
For those of us who were around in the early to mid 1990's, we
will remember that the i825xx ethernet support was not something
that was considered sufficiently vetted for 24/7 use.
Folks might be inclined to use *functional* ISA hardware on some
near expired P3 ISA machines for dedicated workhorse applications,
but the odds of using (and relying on) one of these old/experimental
drivers is essentially nil. So lets remove them.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The parallel port is largely replaced by USB, and even in the
day where these drivers were current, the documented speed was
less than 100kB/s. Let us not pretend that anyone cares about
these drivers anymore, or worse - pretend that anyone is using
them on a modern kernel.
As a side bonus, this is the end of legacy parallel port ethernet,
so we get to drop the whole chunk relating to that in the legacy
Space.c file containing the non-PCI unified probe dispatch.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
It was amusing that linux was able to make use of this 1980's
technology on machines long past its intended lifespan, but
it probably should go now.
To set some context, the 3c501 was designed in the 1980's to be
used on 8088 PC-XT 8bit ISA machines. It was built using a large
number of discrete TTL components and truly looks like a relic
of the ancient past before large scale integration was common.
But from a functional point of view, the real issue, as stated
in the (also obsolete) Ethernet-HowTo, is that "...the 3c501 can
only do one thing at a time -- while you are removing one packet
from the single-packet buffer it cannot receive another packet,
nor can it receive a packet while loading a transmit packet."
You know things are not good when the Kconfig help text suggests
you make a cron job doing a ping every minute.
Hardware that old and crippled is simply not going to be used by
anyone in a time where 10 year old 100Mbit PCI cards (that are
still functional) are largely give-away items.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This driver was specific to a "professional workstation" line
of products from around 1993 that used the i82596 ethernet chip
as an on-board ethernet solution.
With a 486 processor, and the premium top of the line model maxing
out at a clock speed of 50MHz, we can safely retire this support.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The Apricot was a 486 PC with 4MB RAM, and an on-board ethernet
via an intel i82596 hard-wired to i/o 0x300.
Those who were using linux in the 1990's will recall that the
i82596 driver was not one of the more stable or widely used
drivers of its day. Combine that with the extremely limited
resources of the platform, and it is truly time to expire the
support for this thing.
There are some old m68k targets who were also using this chip,
so rather than poll the m68k user base, we simply cut out the
x86/Apricot support here in this commit.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Delete successive tests to the same location. rc was previously tested and
not subsequently updated. efx_phc_adjtime can return an error code, so the
call is updated so that is tested instead.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@s exists@
local idexpression y;
expression x,e;
@@
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
... when != \(y = e\|y += e\|y -= e\|y |= e\|y &= e\|y++\|y--\|&y\)
when != \(XT_GETPAGE(...,y)\|WMI_CMD_BUF(...)\)
*if ( \(x == NULL\|IS_ERR(x)\|y != 0\) )
{ ... when forall
return ...; }
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct name of the transmit DMA channel field in struct emac_priv
is txchan, not txch.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
remove redundant code from build_inline_wqe()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-By: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates Copyright year to 2013
v2: Changed Copyright year on Makefile
Signed-off-by: Akeem G. Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The rmb in the Tx cleanup path is a much stronger barrier than we really need.
All that is really needed is a read_barrier_depends since the location of the
EOP descriptor is dependent on the eop_desc value.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the physical function (PF) is reset for any reason the statistics
collection in ixgbevf_update_stats needs to wait to update until after
the reset synchronization ensures that the PF driver is up and running
and is finished with its own reset. Go ahead and clear the link flag to
indicate this when the control message from the PF is received. The
reset synchronization and recovery in the watchdog task will eventually
set the link flag up when the PF has resumed.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use dev_info to log link up/down messages.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The out of tree driver and the in kernel driver should use the same
interrupt handling logic for mailbox interrupts. The difference in
the handlers was causing dissimilar behavior between the two drivers
complicating debug and trouble shooting.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to both improve the performance and reduce the size of
ixgbe_tx_map. To do this I have expanded the work done in the main loop by
pushing first into tx_buffer. This allows us to pull in the dma_mapping_error
check, the tx_buffer value assignment, and the initial DMA value assignment to
the Tx descriptor. The net result is that the function reduces in size by a
little over a 100 bytes and is about 1% or 2% faster.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to improve the efficiency of the Tx flags in ixgbe by
aligning them with the values that will later be written into either the
cmd_type or olinfo. By doing this we are able to reduce most of these
functions to either just a simple shift followed by an or in the case of
cmd_type, or an and followed by an or in the case of olinfo.
To do this I also needed to change the logic and/or drop some flags. I
dropped the IXGBE_TX_FLAGS_FSO and it was replaced by IXGBE_TX_FLAGS_TSO since
the only place it was ever checked was in conjunction with IXGBE_TX_FLAGS_TSO.
I replaced IXGBE_TX_FLAGS_TXSW with IXGBE_TX_FLAGS_CC, this way we have a
clear point for what the flag is meant to do. Finally the
IXGBE_TX_FLAGS_NO_IFCS was dropped since were are already carrying the data
for that flag in the skb. Instead we can just check the bitflag in the skb.
In order to avoid type conversion errors I also adjusted the locations
where we were switching between CPU and little endian.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were spending cycles separating the FCoE and TSO contexts even though we
always overwriting the context anyway. Instead of doing that we can just
use context 0 for all descriptors.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to reduce the overhead for workloads that are not
using either TSO or checksum offloads. Most of the time the compiler
should jump ahead after failing this check to the VLAN check since in the
ixgbe_tx_csum call we start with that check as well.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
IEEE DCBx has a mechanism to change the default user priority. In
the normal case the OS can handle this via cgroups, iptables, socket,
options etc.
With SR-IOV and direct assigned VF devices the default priority
needs to be set by the PF device so the inserted VLAN tag is
correct.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: Marcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
These are copying data into 16 char arrays. They all specify that the
first string can't be more than 11 characters but once you add on the
"-rx-" and the NUL character there isn't space for the %d.
The first string is probably never going to be 11 characters, but if it
is then let's truncate the string instead of corrupting memory.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is heavy transmission traffic in the CPDMA, then Rx descriptors
memory is also utilized as tx desc memory looses all rx descriptors and the
driver stops working then.
This patch adds boundary for tx and rx descriptors in bd ram dividing the
descriptor memory to ensure that during heavy transmission tx doesn't use
rx descriptors.
This patch is already applied to davinci_emac driver, since CPSW and
davici_dmac shares the same CPDMA, moving the boundry seperation from
Davinci EMAC driver to CPDMA driver which was done in the following
commit
commit 86d8c07ff2
Author: Sascha Hauer <s.hauer@pengutronix.de>
Date: Tue Jan 3 05:27:47 2012 +0000
net/davinci: do not use all descriptors for tx packets
The driver uses a shared pool for both rx and tx descriptors.
During open it queues fixed number of 128 descriptors for receive
packets. For each received packet it tries to queue another
descriptor. If this fails the descriptor is lost for rx.
The driver has no limitation on tx descriptors to use, so it
can happen during a nmap / ping -f attack that the driver
allocates all descriptors for tx and looses all rx descriptors.
The driver stops working then.
To fix this limit the number of tx descriptors used to half of
the descriptors available, the rx path uses the other half.
Tested on a custom board using nmap / ping -f to the board from
two different hosts.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The lines
if (mlx4_is_mfunc(dev)) {
nreq = 2;
} else {
which hard code the number of requested msi-x vectors under multi-function
mode to two can be removed completely, since the firmware sets num_eqs and
reserved_eqs appropriately Thus, the code line:
nreq = min_t(int, dev->caps.num_eqs - dev->caps.reserved_eqs, nreq);
is by itself sufficient and correct for all cases. Currently, for mfunc
mode num_eqs = 32 and reserved_eqs = 28, hence four vectors will be enabled.
This triples (one vector is used for the async events and commands EQ) the
horse power provided for processing of incoming packets on netdev RSS scheme,
IO initiators/targets commands processing flows, etc.
Reviewed-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5b4c4d3686 "mlx4_en: Allow communication between functions on
same host" introduced a regression under which a bridge acting as vSwitch
whose uplink is an mlx4 Ethernet device become non-operative in native
(non sriov) mode. This happens since broadcast ARP requests sent by VMs
were loopback-ed by the HW and hence the bridge learned VM source MACs
on both the VM and the uplink ports.
The fix is to place the DMAC in the send WQE only under SRIOV/eSwitch
configuration or when the device is in selftest.
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yan Burman <yanb@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The xgmac driver assumes 1 frame per descriptor. If a frame larger than
the descriptor's buffer size is received, the frame will spill over into
the next descriptor. So check for received frames that span more than one
descriptor and discard them. This prevents a crash if we receive erroneous
large packets.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than use an extra #define for something that already exists, use the
kernel #define for the PTP port.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
To prevent a race condition where an skb has been saved to return the Tx
timestamp later and the driver is removed, add a check to determine if we
have an skb stored and, if so, free it.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a check against possible Rx timestamp freezing in the hardware via
watchdog mechanism. This situation can occur when an Rx timestamp has been
latched, but the packet has been dropped because the Rx ring is full.
Whenever a packet comes in that should be timestamped, the Rx timestamp
gets latched into the hardware registers and we will store the jiffy value
in the rx_ring. The watchdog will keep track of his own jiffy timer
whenever there is no valid timestamp in the registers.
If the watchdog detects a valid timestamp in the registers, meaning that no
Rx packet has consumed it yet, it will check which time is most recent: the
last time in the watchdog or any time in the rx_rings. If the most recent
"event" was more than 5 seconds ago, it will flush the Rx timestamp and
print a warning message to the syslog.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When transmitting a packet that must return a Tx timestamp, a work item
gets scheduled to poll for the Tx timestamp being completed in hardware.
Add a timeout on this work item of 15 seconds from when the driver gets the
skb, after which it will stop polling. Report via stats and system log if
this occurs.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable SW timestamping for situations where the user may prefer it over HW
timestamping or there may not be HW timestamping.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Matthew Vick <matthew.vick@intel.com>
Acked-by: Jacob Keller <Jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of our adapters have internal sensors that report thermal data. This
patch enables reporting of that data via sysfs.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of our devices have internal sensors for reporting thermal data.
This patch creates the interface to the sensors for exporting via sysfs.
Subsequent patch will actually export the data.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some of our adapters have sensors on them accessible via i2c and a private
interface. This patch implements the kernel interface for i2c to those sensors.
Subsequent patches will provide functions to export that data.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement callback in the driver for the new PCI bus driver
interface that allows the user to enable/disable SR-IOV
virtual functions in a device via the sysfs interface.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On 82574, 82583, 82579, I217 and I218 add support for hardware time
stamping of all or no Rx packets and Tx packets which have the
SKBTX_HW_TSTAMP flag set. Update the .get_ts_info ethtool operation to
report the supported time stamping modes, and enable and disable hardware
time stamping with the SIOCSHWTSTAMP ioctl.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the standard #defines for PCIe Capability ASPM fields.
Previously we used PCIE_LINK_STATE_L0S and PCIE_LINK_STATE_L1 directly, but
these are defined for the Linux ASPM interfaces, e.g.,
pci_disable_link_state(), and only coincidentally match the actual register
bits. PCIE_LINK_STATE_CLKPM, also part of that interface, does not match
the register bit.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
CC: e1000-devel@lists.sourceforge.net
Acked-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add the ability to query and set Energy Efficient Ethernet parameters via
ethtool for applicable devices.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is to fix up a build problem with a wireless driver due to the
dynamic-debug patches in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The code to print the FIFO size in tc574_config computes it as:
8 << config & Ram_size
which evaluates the '<<' first, but the actual intent is to evaluate the
'&' first. Add parentheses to enforce desired evaluation order.
Signed-off-by: Nickolai Zeldovich <nickolai@csail.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x does an internal GRO pass but doesn't provide gso_segs, thus
breaking qdisc_pkt_len_init() in case ingress qdisc is used.
We store gso_segs in NAPI_GRO_CB(skb)->count, where tcp_gro_complete()
expects to find the number of aggregated segments.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 6f0333b ("r8169: use 50% less ram for RX ring") the rx
ring buffers are always copied making dirty_rx useless.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The coalesce parameters was set only on the first queue, which caused
interrupt rates to be larger on all the other queues.
This patch allows interrupt rates to be reduced for certain workloads
and colaesce parameters by 41%.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Cc: steved@us.ibm.com
Cc: toml@us.ibm.com
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleanup a set of conditional tests.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The removed code block is duplicated in e1000e_write_itr() so use that
instead.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch corrects a bug introduced by commit f3444d8b. The rxmtrl value for
the UDP port to timestamp on was moved above the switch statement, but was
overwritten to 0 if the ioctl selected one of the V1 filters.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch modifies ixgbe_debugfs.c and the Makefile for the ixgbe
driver to only compile the file when the config is enabled. This means
we can remove the #ifdef inside the ixgbe_debugfs.c file.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
rx_long_byte_count can be removed since it is duplicated in rx_bytes
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
WARNING: Prefer netdev_info(netdev, ... then dev_info(dev, ...
then pr_info(... to printk(KERN_INFO ...
v2 - remove unnecessary "e1000e:" prefix as pointed out by Joe Perches
since that produces a redundant "e1000e:" in the log message
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
...discovered during code inspection.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When there is heavy traffic and the cable is pulled, the driver must reset
the adapter to flush the Tx queue in hardware. This causes the reset path
to be scheduled and logs the message "Reset adapter" which could be mis-
interpreted as an error by the user. Change how the reset path is invoked
for this scenario by using the same method done in an existing work-around
for 80003es2lan (i.e. set a flag and if the flag is set in the reset code
do not log the "Reset adapter" message since the reset is expected).
Re-name the FLAG_RX_RESTART_NOW to FLAG_RESTART_NOW since it is used for
resets in both the Rx and Tx specific code.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Energy Efficient Ethernet on 82579 and I217 should only be enabled if not
disabled by the user, if the link is full duplex and the link partner has
similar EEE capabilities (stored in different EMI registers on the two
different parts).
After enabling EEE, read the IEEE MMD register 3.1 (which is also stored in
different EMI registers on the two different parts) to clear the count of
received Tx/Rx LPI indications.
Also, rename I217_EEE_100_SUPPORTED to I82579_EEE_100_SUPPORTED to indicate
the bit is valid starting with I82579 (released before I217).
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When connected to certain switches, the 82577 PHY might drop link
unexpectedly. Work around the issue by setting the Mean Square Error
higher than the hardware default.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Extended Management Interface (EMI) registers are accessed by first
writing the EMI register offset to the EMI_ADDR regiter and then either
reading or writing the data to/from the EMI_DATA register. Add helper
functions for performing these steps and convert existing EMI register
accesses accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On I217, the bit that indicates an invalid EEPROM (NVM) image checksum has
changed from previous ICH/PCH LOMs. When validating the EEPROM checksum,
check the appropriate bit on different devices.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When data blocks are written to the EEPROM, the HW/SW/FW semaphore must be
held for the duration. With large data blocks on 80003es2lan, 82571 and
82572, this can take too long and cause the firmware to take ownership of
the semaphore and consequently ownership of writes to the EEPROM.
Instead, acquire and release the semaphore for each page of the block
written.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enables flow control to be set in SerDes autoneg mode. This is what is
done for copper, but relies on a different set of register/bit checks
since this is all done within the Mac registers.
Remove inapplicable comment in defines.h
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since submit 621b4d6 the bnx2x driver support FW GRO.
However, when using the device with GRO enabled in bridging
scenarios throughput is very low, as the bridge expects all
incoming packets to be passed with CHECKSUM_PARTIAL -
a demand which is satisfied by the SW GRO implementation,
but was missed in the bnx2x driver implementation (which returned
CHECKSUM_UNNECESSARY).
Now, given that the traffic is supported by FW GRO (TCP/IP),
the bnx2x driver calculates the pseudo checksum by itself,
passing skbs with CHECKSUM_PARTIAL and giving a much better
throughput when receiving GRO traffic.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling interrupts, acknowledge the interrupt only
after configuring the IGU to the correct interrupt mode
(otherwise it would dirty selftests)
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get better control over interrupts during panic, and allow FW to
test outgoing Tx packets when stop-on-error is allowed.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This revises and enhances the bnx2x register dump facilities,
adding support for `ethtool -w' on top of `ethtool -d'.
Signed-off-by: Miriam Shitrit <miris@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a device is configured to act as either iscsi or fcoe
device in its nvram, prevent the other from being misused by
preventing its activation in the driver.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On rare occasions, self test link may fail since the link is
being sampled while it's still being stabilized.
To correct this behaviour, try to sample the link for 2 seconds
prior to declaring a failure.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current logic causes chips running in switch dependent multi-function
FCoE mode not to configure their MAC, leading to an all 0s MAC.
This patch configures the interface with the SAN Mac instead.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Self-tests following boot from SAN have failed as the
UNDI driver might leave some NIG interrupt indications.
This patch does the clean-up, clearing those indications
and allowing the test to pass.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
Documentation/networking/ip-sysctl.txt
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
Both conflicts were simply overlapping context.
A build fix for qlcnic is in here too, simply removing the added
devinit annotations which no longer exist.
Signed-off-by: David S. Miller <davem@davemloft.net>
TG3_PHY_AUXCTL_SMDSP_ENABLE/DISABLE macros do a blind write to the phy
auxiliary control register and overwrite the EXT_PKT_LEN (bit 14) resulting
in intermittent crc errors on jumbo frames with some link partners. Change
the code to do a read/modify/write.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netconsole is enabled, logging messages generated during tg3_open
can result in a null pointer dereference for the uninitialized tg3
status block. Use the irq_sync flag to disable polling in the early
stages. irq_sync is cleared when the driver is enabling interrupts after
all initialization is completed.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a5e371f61a ("drivers/net: delete
all code/drivers depending on CONFIG_MCA") most of the MCA drivers went,
including the Kconfig/Makefile hooks for ibmlana, but it seems that I
missed the "git rm" on these actual driver files, and with the namespace
overlap with machine check architecture, it got missed by various git
grep type checking done at that time.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only user is cxgb3 driver.
old_neigh is used to check device change, but it must not happen
on redirect. In this sense, we can remove old_neigh argument.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit e49cc34f introduced an unconditional IRQ_HANDLED return in be_intx()
to workaround Lancer and BE2 HW issues. This is bad as it prevents the kernel
from detecting interrupt storms due to broken HW.
The BE2/Lancer HW issues are:
1) In Lancer, there is no means for the driver to detect if the interrupt
belonged to device, other than counting and notifying events.
2) In Lancer de-asserting INTx takes a while, causing the INTx irq handler
to be called multiple times till the de-assert happens.
3) In BE2, we see an occasional interrupt even when EQs are unarmed.
Issue (1) can cause the notified events to be orphaned, if NAPI was already
running.
This patch fixes this issue by scheduling NAPI only if it is not scheduled
already. Doing this also takes care of possible events_get() race that may be
caused due to issue (2) and (3). Also, IRQ_HANDLED is returned only the first
time zero events are detected.
(Thanks Ben H. for the feedback and suggestions.)
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in/out_be32 accessors are Power arch centric whereas
ioread/writebe32 are available in other arches. Also, unlike
in/out_be32, ioread/writebe32 expect non-volatile address arguments.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is werid that qlge driver supports NETIF_F_TSO6 but
not NETIF_F_IPV6_CSUM. This also causes some kernel warning [1]
when VLAN device setups on a qlge interface.
I think the qlge hardware doesn't support NETIF_F_IPV6_CSUM,
so we have to just remove the NETIF_F_TSO6 flag.
After this patch, the TCP/IPv6 traffic becomes normal again,
no kernel warnings any more.
NOTE: I only tested it on 2.6.32 kernel, even if the upstream
kernel could fix this automatically (it is hard to track NETIF*
flags), removing it is also safe.
1. https://bugzilla.redhat.com/show_bug.cgi?id=891839
Cc: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Cc: Ron Mercer <ron.mercer@qlogic.com>
Cc: linux-driver@qlogic.com
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Acked-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Tony Lindgren <tony@atomide.com>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: Kevin Hilman <khilman@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David S. Miller <davem@davemloft.net>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: "David S. Miller" <davem@davemloft.net>
CC: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Cesar Eduardo Barros <cesarb@cesarb.net>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: "David S. Miller" <davem@davemloft.net>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David S. Miller <davem@davemloft.net>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Stephen Hemminger <shemminger@vyatta.com>
CC: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David S. Miller <davem@davemloft.net>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David S. Miller <davem@davemloft.net>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jeff Kirsher <jeffrey.r.kirsher@intel.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: Jay Cliburn <jcliburn@gmail.com>
CC: Chris Snook <chris.snook@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Chris Snook <chris.snook@gmail.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
CC: "David S. Miller" <davem@davemloft.net>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Mathieu Poirier <mathieu.poirier@linaro.org>
CC: Greg Ungerer <gerg@uclinux.org>
CC: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: David S. Miller <davem@davemloft.net>
There is a missing break statement so FLASH_5762_EEPROM_HD gets treated
like FLASH_5762_EEPROM_LD.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is used on Microblaze and will be used
on Arm Zynq.
Microblaze doesn't define NO_IRQ and no IRQ is 0.
Arm still uses NO_IRQ as -1 and there is no option
to connect IRQ to irq 0.
That's why <= 0 is only one option how to find out
undefined IRQ.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Axi ethernet can't be used on PPC because it is
little endian IP and PPC is big endian.
This system can't be designed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of the previous driver unload flow, whenever bnx2x is
loaded after the UNDI driver it closes all Rx traffic.
However, this leads to management traffic also being stopped until
the network interface associated with one of its functions gets loaded.
To remedy this, management traffic is re-opened once the 'cleaning'
after the previous driver ends.
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating Tx queues, if for some reason
(e.g., lack of memory) allocation fails, driver will incorrectly
calculate the pointers of the various queues.
This patch repositions all pointers in such a case to point at
sequential structures in memory, allowing the bnx2x macros to
be used correctly when accessing them.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 70ac618c07 ("ptp: fixup Kconfig for two PHC drivers.") removed all
dependencies for the blackfin hardware time-stamping Kconfig entry. Hardware
time-stamping is only available on BF518 though. Since the Kconfig entry is
'default y', just updateing your kernel source and running `make defconfig` will
result in the the following build errors:
drivers/net/ethernet/adi/bfin_mac.c:694: error: implicit declaration of function ‘bfin_read_EMAC_PTP_CTL’
drivers/net/ethernet/adi/bfin_mac.c:702: error: implicit declaration of function ‘bfin_write_EMAC_PTP_FV3’
drivers/net/ethernet/adi/bfin_mac.c:712: error: implicit declaration of function ‘bfin_write_EMAC_PTP_CTL’
drivers/net/ethernet/adi/bfin_mac.c:717: error: implicit declaration of function ‘bfin_write_EMAC_PTP_FOFF’
...
This patch adds back the dependency on BF518, and since it does not make sense
to expose this config option when the blackfin MAC driver is not enabled also
restore the dependency on BFIN_MAC.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I move the return down a line after the debugging printk.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Static checkers complained that the E1H_FUNC_MAX define is used
incorrectly in bnx2x_pretend_func(). The complaint was justified,
although its not a real bug, as the first part of the conditional
protects us in this case (a real bug would happen if a VF tried to
use the pretend func, but there are no VFs in E1H chips).
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With Hard-Wired firmware configuration it was incorrectly provisioning the VFs
Channel Access Rights Mask.
Signed-off-by: Jay Hernandez <jay@chelsio.com>
Signed-off-by: Vipul Pandya <vipul@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"vfop" is NULL here. I've changed the debugging to not use it.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ariel Elior <ariele@broadcom.com>
Acked-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCMA is a Broadcom specific bus with devices AKA cores. All recent BCMA
based SoCs have gigabit ethernet provided by the GBit MAC core. This
patch adds driver for such a cores registering itself as a netdev. It
has been tested on a BCM4706 and BCM4718 chipsets.
In the kernel tree there is already b44 driver which has some common
things with bgmac, however there are many differences that has led to
the decision or writing a new driver:
1) GBit MAC cores appear on BCMA bus (not SSB as in case of b44)
2) There is 64bit DMA engine which differs from 32bit one
3) There is no CAM (Content Addressable Memory) in GBit MAC
4) We have 4 TX queues on GBit MAC devices (instead of 1)
5) Many registers have different addresses/values
6) RX header flags are also different
The driver in it's state is functional how, however there is of course
place for improvements:
1) Supporting more net_device_ops
2) SUpporting more ethtool_ops
3) Unaligned addressing in DMA
4) Writing separated PHY driver
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following warning when building with W=1 option:
drivers/net/ethernet/freescale/fec.c:810:1: warning: '__inline__' is not at beginning of declaration [-Wold-style-declaration]
The inline declaration is pointless in this function, so just remove it.
While at it, also remove the other 'inline' declarations.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Gortmaker says:
====================
I'd like to propose that we get rid of these old 8390 EISA drivers.
Of the five deleted here, I wrote four -- and while that doesn't give
me any authority for deletion above anyone else, it does at least
allow me to comment on the absolute absence of anyone reaching
out to the driver author for assistance in the last dozen years.
Eventually we'll probably get rid of EISA bus support, since in
x86, the hardware is close to 20 years old and already too resource
constrained to be useful today. However there might still be
a few DEC Alpha enthusiasts with old EISA machines kept alive,
and so I expect we'll have to wait a bit longer to get unanimous
agreement to proceed with the full EISA removal (although I'd
love to be proven wrong on that).
Most of the DEC Alpha machines shipped in a PCI configuration, and
even the few that were EISA had DEC tulip based ethernet and no
reason to be needing the inferior 8390 technology. So the interest
here for any possible DEC enthusiasts with EISA boxes about these
old 8390 drivers should be nil.
These really were rare cards -- in fact the smc-ultra32 is the only
one that I'd ever seen in person. Even back in the mid 90's when
the drivers were written, I would guess that the user base was less
than 10 people across all of them.
The following patch was created with --irreversible-delete for
ease of review (it skips showing the content of files that are
deleted); however the complete patch can be pulled as per below.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In this patch the SR-IOV code is segregated from the main bulk of
the bnx2x code. The CONFIG_BNX2X_SRIOV define is added to Broadcom's
Kconfig, and allows the elision of the building of all the SR-IOV
support code in the driver.
The define is dependant on the kernel CONFIG_PCI_IOV configuration
define.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Report correct hardware stamping capability by ethtool interface.
The v1.0 ptp4l check it.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use more current logging styles.
Convert printks to pr_<level> and
printks with ("%s: ...", dev->name to netdev_<level>(dev, "...
Add pr_fmt #defines where appropriate.
Coalesce formats.
Use pr_<level>_once where appropriate.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NS8390 chip was essentially the 1st widespread PC ethernet
chip, starting its life on 8 bit ISA cards in the late 1980s.
Even with better technologies available (bus mastering etc)
the 8390 managed to get used on a few rare EISA cards in the
early to mid 1990s.
The EISA bus in the x86 world was largely confined to systems
ranging from 486 to 586 (essentially 200MHz or lower, and less
than 100MB RAM) -- i.e. machines unlikely to be still in service,
and even less likely to be running a 3.9+ kernel.
On top of that, only one of the five really ever was considered
non-experimental; the smc-ultra32 was the one -- since it was
largely just an EISA version of the popular smc-ultra ISA card.
All the others had such a tiny user base that they simply never
could be considered anything more than experimental.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
We threw away the microchannel support, but the removal wasn't
completely trivial since there was namespace overlap with the
machine check support, and hence some orphaned dependencies
survived the deletion. This attempts to sweep those up and
send them to the bit-bucket.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function ethoc_set_mac_address() was incorrectly using passed pointer as
pointer to address, that is not correct.
Struct sockaddr have to be be used here.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit de0a41484c added Kconfig logic to
select HWMON and removed all the IS_ENABLED(CONFIG_HWMON) checks in the
tg3.c file. It missed this one check in the header.
Update version to 3.129 and update copyright year.
Signed-off-by: Nithin Nayak Sujir <nsujir@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the code to detect PCI function number on 5717, 5719, and 5720.
If shared memory does not have proper signature, read the function number
from register directly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detect NVRAM types for 5762 and read OTP firmware version.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add basic support for 5762 which is a 57765_PLUS class device.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MX6 and mx28 support enhanced DMA descriptor buff to support 1588
ptp. But MX25, MX3x, MX5x can't support enhanced DMA descriptor buff.
Check fec type and choose correct DMA descriptor buff type.
Remove static config CONFIG_FEC_PTP.
ptp function will be auto detected.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sparse complains that:
drivers/net/ethernet/broadcom/tg3.c:5670:55: sparse: constant
0x7fffffffffffffff is so big it is long long (on x86/32 bit)
so we suffix the constant with LL in the header file.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
rcu_read_lock was missing here
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, when invalid address was passed to ndo_set_mac_address,
random mac was generated and set. Fix this by returning -EADDRNOTAVAIL
in this situation.
Also polish the code around a bit.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
NET_ADDR_SET is set in dev_set_mac_address() no need to alter
dev->addr_assign_type value in drivers.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bestcomm dma hardware, and some of its users like the FEC ethernet
component, is used in different FreeScale parts, including non-powerpc
parts like the ColdFire MCF547x & MCF548x families. Don't keep the
driver hidden in arch/powerpc where it is inaccessible for other arches.
.c files are moved to drivers/dma/bestcomm, while .h files are moved to
include/linux/fsl/bestcomm. Makefiles, Kconfigs and #include directives
are updated for the new file locations.
Tested by recompiling for MPC5200 with all bestcomm users enabled.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Fix the following error reported by kbuild test robot.
static declaration of 'qlcnic_restore_indev_addr' follows
non-static declaration.
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable 83xx virtual NIC mode
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Huang, Xiong