The programmed frequency on xc4000 is not the middle
frequency, but the initial frequency on the bandwidth range.
However, the DVB API works with the middle frequency.
This works fine on set_frontend, as the device calculates
the needed offset. However, at get_frequency(), the returned
value is the initial frequency. That's generally not a big
problem on most drivers, however, starting with changeset
6fe1099c7a, the frequency drift is taken into account at
dib7000p driver.
This broke support for PCTV 340e, with uses dib7000p demod and
xc4000 tuner.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The programmed frequency on xc5000 is not the middle
frequency, but the initial frequency on the bandwidth range.
However, the DVB API works with the middle frequency.
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This meta-tag is used by some distros to help them package
the firmware and generate proper initrd images.
So, add the firmware names there.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The firmware name at:
http://www.kernellabs.com/firmware/xc4000/
Is different from the one at the Kernel. Update it
try first the new name, falling back to the previous one
if the new name can't be found.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
As reported by Kbuildtest:
warning: (VIDEO_PVRUSB2 && VIDEO_TLG2300 && VIDEO_USBVISION && VIDEO_GO7007 && VIDEO_AU0828_V4L2 && VIDEO_CX231XX && VIDEO_TM6000 && VIDEO_EM28XX && VIDEO_IVTV && VIDEO_MXB && VIDEO_CX18 && VIDEO_CX23885 && VIDEO_CX88 && VIDEO_BT848 && VIDEO_SAA7134 && VIDEO_SAA7164) selects VIDEO_TUNER which has unmet direct dependencies (MEDIA_SUPPORT && MEDIA_TUNER)
That happens when:
# CONFIG_MEDIA_ANALOG_TV_SUPPORT is not set
CONFIG_MEDIA_DIGITAL_TV_SUPPORT=y
# CONFIG_MEDIA_RADIO_SUPPORT is not set
# CONFIG_MEDIA_SDR_SUPPORT is not set
CONFIG_VIDEO_AU0828_V4L2=y
CONFIG_VIDEO_CX231XX=y
CONFIG_VIDEO_TM6000=y
CONFIG_VIDEO_EM28XX=y
CONFIG_VIDEO_TUNER=y
CONFIG_MEDIA_SUPPORT=y
With means that we need to enable MEDIA_TUNER also when DTV
is enabled. While the above config doesn't cover, if we enable
SDR, the same error can also happen.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is needed for PCTV 522e support.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This is needed for PCTV 522e support.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
The struct prototype is defined at the beginning of the code as
"si2157_ops" but the real struct is called "si2157_tuner_ops".
This is causing the name to be empty on this info msg: si2157 16-0060:
si2157: found a '' in cold state
[crope@iki.fi: commit msg from Luis email reply]
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Cc: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Tell used TV standard and bandwidth for tuner firmware.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add support for Si2158 A20 chip.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move chip initialization related code from si2157_set_params to
si2157_init.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
We want also read data from firmware. Add support for it. Copied from
si2168 driver.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add static to tda m_* variables in the header. They don't need to be global.
With some cleanup they could probably even be marked const.
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=68191
Reported-by: Christian Schneider <christian@ch-sc.de>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Some drivers, like au0828 are very sensitive to tuner sleep and may
break if the sleep happens too fast. Also, by keeping the tuner alive
for a while could speedup tuning process during channel scan. So,
change the logic to delay the actual sleep to 5 seconds after its
command.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
WARNING: please, no space before tabs
+#define XC_PRODUCT_ID_FW_LOADED ^I0x1388$
WARNING: please, no space before tabs
+#define DK_SECAM_A2LDK3 ^I13$
WARNING: please, no space before tabs
+#define DK_SECAM_A2MONO ^I14$
WARNING: please, no space before tabs
+#define FM_RADIO_INPUT2 ^I21$
WARNING: please, no space before tabs
+#define FM_RADIO_INPUT1 ^I22$
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There's absolutely no reason to wrap msleep() call here.
Just rename all occurences of xc_wait() with msleep() and
remove the wrapper function.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTfR2zAAoJEHm+PkMAQRiG3noH/2s+KUge3qO2M+AmxttUo74B
+npAMdbqYR3MdEiwxYZfsHcMu4Ye/IKLcrh4pydB5hI2mdjtGkH1bnmia0f1ve/c
Z/a0256+W8gWp7mcUBqSNztqLPAWa7wKOqNdLjj5idr1BSj6u8im+fQ9FBh2woki
1fyYAuq/60lq4CMOKJvkA95V1Ome/jO+8tS4PguOgsCETQxCVFGurZcBbG3Mx5Y3
v+ioCqeRc6GvxPFR6YngnTZCrsLxSRT3tnO2Qy5zX7dxjIQkCEbvIckpBQv01Y3R
wNUaX+2Jae207igxrEv8CjmCFnmZFuUI15aWWCy6fOS/j8bjuk6ThYJO8N4ZBM0=
=2ShG
-----END PGP SIGNATURE-----
Merge tag 'v3.15-rc6' into patchwork
Linux 3.15-rc6
* tag 'v3.15-rc6': (1314 commits)
Linux 3.15-rc6
Btrfs: send, fix incorrect ref access when using extrefs
Btrfs: fix EIO on reading file after ioctl clone works on it
scripts/checksyscalls.sh: Make renameat optional
asm-generic: Add renameat2 syscall
ia64: add renameat2 syscall
parisc: add renameat2 syscall
m68k: add renameat2 syscall
sysfs: make sure read buffer is zeroed
ahci: imx: PLL clock needs 100us to settle down
PCI: Wrong register used to check pending traffic
target: fix memory leak on XCOPY
random: fix BUG_ON caused by accounting simplification
clk: tegra: Fix wrong value written to PLLE_AUX
staging: rtl8723au: Do not reset wdev->iftype in netdev_close()
ACPI / video: Revert native brightness quirk for ThinkPad T530
staging: rtl8723au: Use correct pipe type for USB interrupts
crush: decode and initialize chooseleaf_vary_r
libceph: fix corruption when using page_count 0 page in rbd
arm64: fix pud_huge() for 2-level pagetables
...
DVB-C uses lower frequencies than DVB-T. Extend frequency range down to
110 MHz in order to support DVB-C. 110 - 862 MHz range is defined by
NorDig Unified 2.2 specification.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Silicon Labs Si2157 silicon tuner driver.
Currently it supports only DVB-T.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was some frequency calculation overflows which caused tuning
failure on 32-bit architecture. Use 64-bit numbers where needed in
order to avoid calculation overflows.
Thanks for the Finnish person, who asked remain anonymous, reporting,
testing and suggesting the fix.
Cc: <stable@vger.kernel.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Correct the initialization values at the start of the function
and use proper variable sizes to prevent overflow.
Signed-off-by: Benjamin Larsson <benjamin@southpole.se>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Coverity CID 1196501: Missing break in switch (MISSING_BREAK)
I introduced that bug recently by commit
96a5b3a869.
As a result, it will flood unintentionally error message to log.
Reported-by: <scan-admin@coverity.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That tuner driver is mainly for DVB API, but there is some V4L2 API
controls for SDR usage. Make driver compile conditional so that V4L2
is not mandatory. Without the V4L2 support driver is build as a DVB
only, without SDR controls.
Fixes following errors reported by kbuild test robot:
ERROR: "v4l2_ctrl_auto_cluster" [drivers/media/tuners/e4000.ko] undefined!
ERROR: "v4l2_ctrl_new_std" [drivers/media/tuners/e4000.ko] undefined!
ERROR: "v4l2_ctrl_handler_init_class" [drivers/media/tuners/e4000.ko] undefined!
ERROR: "v4l2_ctrl_handler_free" [drivers/media/tuners/e4000.ko] undefined!
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
All error/warnings:
drivers/built-in.o: In function `e4000_set_params':
>> e4000.c:(.text+0x1219a1b): undefined reference to `__umoddi3'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Rename some variables.
Change error status checks from (ret < 0) to (ret).
No actual functionality changes.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
That comes possible after driver was converted to kernel I2C model
(I2C binding & proper I2C client with no gate control hack). All
nasty low level I2C routines are now covered by regmap.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Gate control is now implemented by rtl2832 I2C adapter so we do not
need proprietary DVB i2c_gate_ctrl() anymore.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement PLL lock control to get PLL lock flag status from tuner
synthesizer.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There was 32-bit overflow on VCO frequency calculation which blocks
tuning to 1073 - 1104 MHz. Use 64 bit number in order to avoid VCO
frequency overflow.
After that fix device in question tunes to following range:
60 - 1104 MHz
1250 - 2207 MHz
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Implement gain and bandwidth controls using v4l2 control framework.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Driver conversion from proprietary DVB tuner model to more
general I2C driver model.
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There is now new tuner types which are not handled on that switch-case.
Print error if unknown tuner type is meet.
drivers/media/tuners/tuner-xc2028.c: In function ‘generic_set_freq’:
drivers/media/tuners/tuner-xc2028.c:1037:2: warning: enumeration value ‘V4L2_TUNER_ADC’ not handled in switch [-Wswitch]
switch (new_type) {
^
drivers/media/tuners/tuner-xc2028.c:1037:2: warning: enumeration value ‘V4L2_TUNER_RF’ not handled in switch [-Wswitch]
Cc: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
tda18272 is programmed just like tda18212, but it also
supports ClearQAM and ATSC.
Add support for them. Tested with a Kworld UB435-Q on both
8VSB and 256QAM modes.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
There are several left overs with my old email address.
Remove their occurrences and add myself at CREDITS, to
allow people to be able to reach me on my new addresses.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Only send a power down command for the device if it is not already
in power down state. That prevents a timeout when trying to talk
with the device.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Set the return variable to an error code as done elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Cc: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This macro is not used. remove it.
Reviewed-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Antti Palosaari