Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Typo fixes submiting/submitting
o Coalesce formats
o Realign arguments
o Add missing terminating '\n' to formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of looping in the code let's use kernel extension to dump small
buffers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace mdelay with usleep_range to avoid busy loop.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert the normal transmit completion path from dev_kfree_skb_any()
to dev_consume_skb_any() to help keep dropped packet profiling
meaningful.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The usage of bond->lock in bond_main.c was completely unnecessary as it
didn't help to sync with anything, most of the spots already had RTNL.
Since there're no more users of bond->lock, remove it.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're safe to remove the bond->lock use from the arp targets because
arp_rcv_probe no longer acquires bond->lock, only rcu_read_lock.
Also setting the primary slave is safe because noone uses the bond->lock
as a syncing mechanism for that anymore.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use RCU to protect against slave release, the proc show function will sync
with the bond destruction by the proc locks and the fact that the bond is
released after NETDEV_UNREGISTER which causes the bonding to remove the
proc entry.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is necessary mainly for two bonding call sites: procfs and
sysfs as it was dereferenced without any real protection.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can remove the lock/unlock as it's no longer necessary since
RTNL should be held while calling bond_alb_set_mac_address().
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 3ad mode the only syncing needed by bond->lock is for the wq
and the recv handler, so change them to use curr_slave_lock.
There're no locking dependencies here as 3ad doesn't use
curr_slave_lock at all.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTNL should be already held in the notifier call so the slave list can
be traversed without a problem, remove the unnecessary bond->lock.
CC: Hariprasad S <hariprasad@chelsio.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines a platform glue layer for Rockchip SoCs which
support arc-emac driver. It ensures that regulator for the rmii is on
before trying to connect to the ethernet controller. It applies right
speed and mode changes to the grf when ethernet settings change.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After merging the wireless-next tree, today's linux-next build (powerpc
allyesconfig) failed like this:
drivers/net/wireless/ath/ath5k/debug.c: In function 'open_file_eeprom':
drivers/net/wireless/ath/ath5k/debug.c:933:2: error: implicit declaration of function 'vmalloc' [-Werror=implicit-function-declaration]
buf = vmalloc(eesize);
^
drivers/net/wireless/ath/ath5k/debug.c:933:6: warning: assignment makes pointer from integer without a cast
buf = vmalloc(eesize);
^
drivers/net/wireless/ath/ath5k/debug.c:960:2: error: implicit declaration of function 'vfree' [-Werror=implicit-function-declaration]
vfree(buf);
^
Caused by commit db906eb210 ("ath5k: added debugfs file for dumping
eeprom"). Also reported by Guenter Roeck.
I have used Geert Uytterhoeven's suggested fix of including vmalloc.h
and so added this patch for today:
From: Stephen Rothwell <sfr@canb.auug.org.au>
Date: Mon, 8 Sep 2014 18:39:23 +1000
Subject: [PATCH] ath5k: fix debugfs addition
Reported-by: Guenter Roeck <linux@roeck-us.net>
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
It removes the owner field updation of driver structure.
It will be automatically updated by module_platform_driver()
Signed-off-by: Varka Bhadram <varkab@cdac.in>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless-next 2014-09-08
Please pull this batch of updates intended for the 3.18 stream...
For the mac80211 bits, Johannes says:
"Not that much content this time. Some RCU cleanups, crypto
performance improvements, and various patches all over,
rather than listing them one might as well look into the
git log instead."
For the Bluetooth bits, Gustavo says:
"The changes consists of:
- Coding style fixes to HCI drivers
- Corrupted ack value fix for the H5 HCI driver
- A couple of Enhanced L2CAP fixes
- Conversion of SMP code to use common L2CAP channel API
- Page scan optimizations when using the kernel-side whitelist
- Various mac802154 and and ieee802154 6lowpan cleanups
- One new Atheros USB ID"
For the iwlwifi bits, Emmanuel says:
"We have a new big thing coming up which is called Dynamic Queue
Allocation (or DQA). This is a completely new way to work with the
Tx queues and it requires major refactoring. This is being done by
Johannes and Avri. Besides this, Johannes disables U-APSD by default
because of APs that would disable A-MPDU if the association supports
U-ASPD. Luca contributed to the power area which he was cleaning
up on the way while working on CSA. A few more random things here
and there."
For the Atheros bits, Kalle says:
"For ath6kl we had two small fixes and a new SDIO device id.
For ath10k the bigger changes are:
* support for new firmware version 10.2 (Michal)
* spectral scan support (Simon, Sven & Mathias)
* export a firmware crash dump file (Ben & me)
* cleaning up of pci.c (Michal)
* print pci id in all messages, which causes most of the churn (Michal)"
Beyond that, we have the usual collection of various updates to ath9k,
b43, mwifiex, and wil6210, as well as a few other bits here and there.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW supports both rx and tx pause frames for flow control.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bit of floor sweeping in a dusty old corner. Convert the "normal"
skb free calls to dev_consume_skb_any() so packet drop tracing will
be more sane.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that dp83640_remove can use skb_queue_purge
instead of looping through itself to flush any entries out of the queue.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mdio-sun4i driver automatically selects REGULATOR and
REGULATOR_FIXED_VOLTAGE because it uses the regulator API. But a
driver selecting a subsystem increases the chance of generating
circular Kconfig dependencies, especially when other drivers depend on
the selected symbol.
Since the regulator API functions are replaced with no-ops when
REGULATOR is disabled, the driver can be built successfully even
without regulator support and so those 'select' dependencies can be
safely dropped.
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
John W. Linville says:
====================
pull request: wireless 2014-09-05
Please pull this batch of fixes intended for the 3.17 stream...
For the mac80211 bits, Johannes says:
"Here are a few fixes for mac80211. One has been discussed for a while
and adds a terminating NUL-byte to the alpha2 sent to userspace, which
shouldn't be necessary but since many places treat it as a string we
couldn't move to just sending two bytes.
In addition to that, we have two VLAN fixes from Felix, a mesh fix, a
fix for the recently introduced RX aggregation offload, a revert for
a broken patch (that luckily didn't really cause any harm) and a small
fix for alignment in debugfs."
For the iwlwifi bits, Emmanuel says:
"I revert a patch that disabled CTS to self in dvm because users
reported issues. The revert is CCed to stable since the offending
patch was sent to stable too. I also bump the firmware API versions
since a new firmware is coming up. On top of that, Marcel fixes a
bug I introduced while fixing a bug in our Kconfig file."
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous patch inadvertently deleted a declaration in the
amd_xgbe_an_tx_training function causing the build to fail.
Add the declaration for 'priv' back to the function.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change e1000_set_eee and e1000_set_eee_i35(0|4) to allow
changes in the advertised EEE speeds from ethtool. Adds two boolean
flags to e1000_set_eee_i35(0|4) to pass in advertised speed data.
Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fixed many errors/warnings and checks in e1000_ethtool.c reported
by checkpatch.pl. Suggestions from Joe Perches and Alexander Duyck
applied as well
Signed-off-by: Krzysztof Majzerowicz-Jaszcz <cristos@vipserv.org>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
As the management counters reach a threshold they will generate an
interrupt so the value can be saved and the counter reset. The
current code does not enable this interrupt on all counters. This
can result in inaccurate statistics.
Update the code to enable all the counters to generate an interrupt
when its threshold is exceeded.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Even if the management counters are configured to be 32 bit register
values, the [rt]xoctetcount_gb and [rt]xoctetcount_g counters are
always 64 bit counter registers. Since they are not being treated as
64 bit values, these statistics are being reported incorrectly (ifconfig,
ethtool, etc.).
Update the routines used to read the registers to access the "hi"
register (an offset of 4 from the "lo" register) to create a 64 bit
value for these 64 bit counters.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the new fancy eth_get_headlen() to pull exactly the headers
into skb->head.
This speeds up GRE traffic (or more generally tunneled traffuc),
as GRO can aggregate up to 17 MSS per GRO packet instead of 8.
(Pulling too much data was forcing GRO to keep 2 frags per MSS)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does not affect the 10/100 GRETH MAC.
Before all GBit GRETH TX descriptor ring cleaning was done in
start_xmit(), when descriptor list became full it activated
TX interrupt to start the NAPI rx poll function to do TX ring
cleaning.
With this patch the TX descriptor ring is always cleaned from
the NAPI rx poll function, triggered via TX or RX interrupt.
Otherwise we could end up in TX frames being sent but not
reported to the stack being sent. On the 10/100 GRETH this
is not an issue since the SKB is copied&aligned into private
buffers so that the SKB can be freed directly on start_xmit()
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cnic module needs to ensure that if ipv6 support is compiled as a module,
then the cnic module cannot be compiled as built-in as it depends on ipv6.
Made this check cleaner via Kconfig
Use simpler IS_ENABLED for CONFIG_VLAN_8021Q check
Signed-off-by: Anish Bhatt <anish@chelsio.com>
Acked-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update ixgbe to drop the ixgbe_get_headlen function in favor of eth_get_headlen.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update igb to drop the igb_get_headlen function in favor of eth_get_headlen.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy timestamping takes a different path than the regular timestamping
does in that it will create a clone first so that the packets needing to be
timestamped can be placed in a queue, or the context block could be used.
In order to support these use cases I am pulling the core of the code out
so it can be used in other drivers beyond just phy devices.
In addition I have added a destructor named sock_efree which is meant to
provide a simple way for dropping the reference to skb exceptions that
aren't part of either the receive or send windows for the socket, and I
have removed some duplication in spots where this destructor could be used
in place of sock_edemux.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We try to call free_netvsc_device(net_device) when "net_device" is NULL.
It leads to an Oops.
Fixes: f90251c8a6 ('hyperv: Increase the buffer length for netvsc_channel_cb()')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 1G SFP RJ45 module is detected, driver must reset the Tx laser
in order to prevent link issues. As part of change, the link_attr_sync
was relocated from vars to params.
Signed-off-by: Yaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-09-04
This series contains updates to i40e, i40evf, ixgbe and ixgbevf.
Catherine adds dual speed module support to i40e. Updates i40e to allow
the user to change link settings when the link is down.
Serey renames i40e_ndo_set_vf_spoofck() to i40e_ndo_set_vf_spookchk()
to be more consistent with what is defined in netdev and removes a
unnecessary variable assignment.
Jesse makes a malicious driver detection warning only print if extended
driver string is enabled for i40e. Fixes a panic under traffic load when
resetting or if/whenever there was a Tx-timeout because we were enabling
the Tx queue to early.
Anjali fixes an issue when PF reset fails, where we were trying to restart
the admin queue which has not been setup at that point. This resolves an
occasional kernel panic when PF reset fails for some reason.
Ethan Zhao replaces the use of a local i40e_vfs_are_assigned() with the
global kernel pci_vfs_assigned() for i40e.
Alex cleans up the FDB handling for ixgbe. This change makes it so that
the behavior for FDB handling is consistent between both the SR-IOV and
non-SR-IOV cases. The main change is that we perform bounds checking on
the number of SR-IOV addresses regardless of if SR-IOV is enabled or not
as we can only support a certain number of addresses in the hardware.
Emil extends the pending Tx work check to the VF interfaces, where the
driver initiates a reset of the interface on link loss with pending Tx
work in order to clear the rings. Introduces a delay for 82599 VFs of
at least 500 usecs to make sure the VFLINKS value is correct, since this
bit tends to flap when a DA or SFP+ cable is disconnected.
Jacob adds code comments in ixgbe to make it more obvious that we are
resetting features based on the fact that we do not have MSI-X enabled,
and cannot use the previous settings. Also resolves a kernel NULL
pointer dereference by limiting the combined total of MACVLAN and
SR-IOV VFs, since the hardware has a limited number of pools available
(64). Previously, no checks were in place to limit the number of
accelerated MACVLAN devices based on the number of pools, which would
be ok since there was already a limit for these well below the number of
available pools. However, SR-IOV uses the very same pools, therefore
we need to ensure that the total number of pools does not exceed the
number of pools available in the hardware.
v2:
- clean up code comment in patch 5 by replacing "an" with "auto
negotiation" based on feedback from Sergei Shtylyov
- removed un-necessary parenthesis around function call in patch 8
based on feedback from Sergei Shtylyov
====================
Simplify the interrupt resource lookup code in cpsw_probe() by the
following:
* Only look at the first member of the resource. As the driver only
works for DT-enabled platforms anyway, a resource of type
IORESOURCE_IRQ will only contain one single entry
(res->start == res->end), so there is no need for the iteration.
* Add a bounds check to avoid overflows if we are passed more than
ARRAY_SIZE(priv->irqs_table) resources.
* Assign 'ret' with the return value of devm_request_irq() so that
cpsw_probe() returns the appropriate error code.
* If devm_request_irq() fails, report the error code in the log
message.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains fixes identified by checkpatch when run with the
strict option.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains fixes identified by checkpatch when run with the
strict option.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to allow parallel detection to work in KR speed. With
both speed modes of KX and KR supported, KX must be checked first.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since device resets can change the current mode it's possible to think
the device is in a different mode than it actually is. Rather than
trying to determine every place that is needed to set/save the current
mode, be safe and check the devices actual mode when needed rather than
trying to track it.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
They are use less, and may generate compiling warnings, so remove them
(microblaze, arc, arm64, and unicore32 have already defined PCI_IOBASE).
The related warnings (with allmodconfig under microblaze):
CC [M] drivers/net/fddi/skfp/skfddi.o
In file included from drivers/net/fddi/skfp/skfddi.c:95:0:
drivers/net/fddi/skfp/h/skfbi.h:151:0: warning: "PCI_IOBASE" redefined
#define PCI_IOBASE 0xffffff00L /* Bit 31..8: I/O Base address */
^
In file included from include/linux/io.h:22:0,
from include/linux/pci.h:31,
from drivers/net/fddi/skfp/skfddi.c:82:
./arch/microblaze/include/asm/io.h:33:0: note: this is the location of the previous definition
#define PCI_IOBASE ((void __iomem *)_IO_BASE)
^
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hw doesn't have a valid MAC address, give a random one and
set it to the hw.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exchange the location of rtl8152_set_mac_address() and
set_ethernet_addr(). Then, the set_ethernet_addr() could
set the MAC address by calling rtl8152_set_mac_address()
later.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for setting/getting rx_copybreak using
generic ethtool tunable.
Defines enic_get_tunable() & enic_set_tunable() to get/set rx_copybreak.
As of now, these two function supports only rx_copybreak.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Calling dma_map_single()/dma_unmap_single() is quite expensive compared
to copying a small packet. So let's copy short frames and keep the buffers
mapped.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should check if the map of the table actually succeeds, and also free
resources accordingly.
Version bumped to 1.2.1.0
Acked-by: Shelley Gong <shelleygong@vmware.com>
Acked-by: Bhavesh Davda <bhavesh@vmware.com>
Signed-off-by: Andy King <acking@vmware.com>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we bring the interface down, phy_stop() will schedule the PHY
state machine to call our link adjustment callback. By the time we do so,
we may have clock gated off the SYSTEMPORT hardware block, and this will
cause bus errors to happen in bcm_sysport_adj_link():
Make sure that we only touch the UMAC_CMD register when there is an
actual link. This is safe to do for two reasons:
- updating the Ethernet MAC registers only make sense when a physical
link is present
- the PHY library state machine first set phydev->link = 0 before
invoking phydev->adjust_link in the PHY_HALTED case
This is a similar fix to the GENET one:
c677ba8b3c ("net: bcmgenet: update
UMAC_CMD only when link is detected").
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Joe Perches