This commit fixes the command value generated for CSUM calculation
when running in big endian mode. The Ethernet protocol ID for IP was
being unconditionally byte-swapped in the layer 3 protocol check (with
swab16), which caused the mvneta driver to not function correctly in
big endian mode. This patch byte-swaps the ID conditionally with
htons.
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Maggie Mae Roxas, the mvneta driver doesn't behave
properly in 10 Mbit/s mode. This is due to a misconfiguration of the
MVNETA_GMAC_AUTONEG_CONFIG register: bit MVNETA_GMAC_CONFIG_MII_SPEED
must be set for a 100 Mbit/s speed, but cleared for a 10 Mbit/s speed,
which the driver was not properly doing. This commit adjusts that by
setting the MVNETA_GMAC_CONFIG_MII_SPEED bit only in 100 Mbit/s mode,
and relying on the fact that all the speed related bits of this
register are cleared at the beginning of the mvneta_adjust_link()
function.
This problem exists since c5aff18204 ("net: mvneta: driver for
Marvell Armada 370/XP network unit") which is the commit that
introduced the mvneta driver in the kernel.
Cc: <stable@vger.kernel.org> # v3.8+
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Reported-by: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Cc: Maggie Mae Roxas <maggie.mae.roxas@gmail.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added FUJITSU SIEMENS A8NE-FM to the list of 32bit DMA boards
>From Tomi O.:
After I added an entry to this MB into the skge.c
driver in order to enable the mentioned 64bit dma disable quirk,
the network data corruptions ended and everything is fine again.
Signed-off-by: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffers for the TSO headers belong to a DMA coherent region which is
allocated at ndo_open() time, and released at ndo_stop() time.
Therefore, and contrary to the TSO payload descriptor buffers, the TSO header
buffers don't need to be unmapped. This commit adds a check to detect a
TSO header buffer and explicitly prevent the unmap.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After adding proper stop/wake thresholds, we can expect a queue to never
be full and drop the NETDEV_TX_BUSY return path. In any case, if the queue
cannot accommodate a TSO packet, the packet would be discarded.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently small MSS values may require too many TSO descriptors for
the default queue size. This commit prevents this situation by fixing
the maximum supported TSO number of segments to 100 and by setting a
minimum Tx queue size. The minimum Tx queue size is set so that at
least 2 worst-case skb can be accommodated.
In addition, the queue stop and wake thresholds values are adjusted
accordingly. The queue is stopped when there's room for only 1 worst-case
skb and waked when the number of descriptors is half that value.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit fixes the current dropped packet count by doing it properly,
increasing the count when a packet is discarded; i.e. the packet is not
processed and the driver returns NETDEV_TX_OK.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffers for the TSO headers belong to a DMA coherent region which is
allocated at ndo_open() time, and released at ndo_stop() time.
Therefore, and contrary to the TSO payload descriptor buffers, the TSO header
buffers don't need to be unmapped. This commit adds a check to detect a
TSO header buffer and explicitly prevent the unmap.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tx descriptor release code currently calls dma_unmap_single() and
dev_kfree_skb_any() if the descriptor is associated with a non-NULL skb.
This is true only for the last fragment of the packet.
This is wrong, however, since every descriptor buffer is DMA mapped and needs
to be unmapped.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently small MSS values may require too many TSO descriptors for
the default queue size. This commit prevents this situation by fixing
the maximum supported TSO number of segments to 100 and by setting a
minimum Tx queue size. The minimum Tx queue size is set so that at
least 2 worst-case skb can be accommodated.
In addition, the queue stop and wake thresholds values are adjusted
accordingly. The queue is stopped when there's room for only 1 worst-case
skb and waked when the number of descriptors is half that value.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver has no need for a custom NAPI weigth. Use the default
one, which has the same value.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'weight' field is only used to pass the weigth to napi initialization
function. This commit removes the field, and instead uses a fixed value to
initialize the napi context.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit makes use of devm_kmalloc_array() for memory allocation and the
recently introduced devm_mdiobus_alloc() API to simplify driver's code.
While here, remove a redundant out of memory error message.
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver does not support multiple rx queues, and so it's a waste
of resources to have a default number larger than one (1).
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use eth_prepare_mac_addr_change and eth_commit_mac_addr_change, instead
of manually checking and storing the MAC address, which makes the
code slightly more robust. This fixes the lack of valid MAC address check
in the driver's .ndo_set_mac_address hook.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit cleans-up mvneta_init(), which initializes the hardware
and allocates the rx/qx queues. The queue allocation is simplified
by using devm_kcalloc instead of kzalloc. The unused phy_addr parameter
is removed. While here, the 'hal' references in the comments are removed.
This commit makes no functionality change.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit checks the return code of mvneta_setup_txq() call
in mvneta_change_mtu(). Also, use the netdevice pointer directly
instead of dereferencing the port structure. While here, let's
fix a tiny comment typo.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A tiny clean-up to improve readability. This commit makes no functionality
change.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, mv643xx_eth_adjust_link() is only used to call mv643xx_adjust_pscr().
This commit renames the latter to the former, and therefore removes the extra
and useless function.
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the TSO helper API has been introduced, this commit makes use
of it to add support for software TSO in this driver.
This feature allows to improve outbound throughput performance significantly.
Running iperf tests shows a 30% improvement, tested on a Kirkwood Openblocks
A6 board.
$ ethtool -K eth0 tso off
$ iperf -c 192.168.0.45 -t 3
------------------------------------------------------------
Client connecting to 192.168.0.45, TCP port 5001
TCP window size: 43.8 KByte (default)
------------------------------------------------------------
[ 3] local 192.168.0.159 port 46389 connected with 192.168.0.45 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 217 MBytes 607 Mbits/sec
$ ethtool -K eth0 tso on
$ iperf -c 192.168.0.45 -t 3
------------------------------------------------------------
Client connecting to 192.168.0.45, TCP port 5001
TCP window size: 43.8 KByte (default)
------------------------------------------------------------
[ 3] local 192.168.0.159 port 46390 connected with 192.168.0.45 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0- 3.0 sec 336 MBytes 938 Mbits/sec
This commit is just an example of the usage of the TSO API, it works fine
but needs some more work. In particular, the descriptor unmapping path must
avoid unmapping the TSO headers.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using dma_map_single() instead of skb_frag_dma_map() allows to unmap
all the descriptors using dma_unmap_single(). This change allows
to introduce software TSO in a less intrusive way.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to ease the addition of new features, let's factorize the
feature list.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As specified in the datasheet, the driver can set the "L4Chk_Mode" flag
(bit 10) in the Tx descriptor command/status to specify that a frame is not
IP fragmented and that the controller is in charge of generating the TCP/IP
checksum. This must be used together with the "GL4chk" flag (bit 17).
These two flags allow to avoid setting the initial TCP checksum in the l4i_chk
field of the Tx descriptor, which is needed to support software TSO.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the code more readable by moving the initial checksum setup
and the command/status preparation to its own function.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the TSO helper API has been introduced, this commit makes use
of it to implement the TSO in this driver.
Using iperf to test and vmstat to check the CPU usage, shows a substantial
CPU usage drop when TSO is on (~15% vs. ~25%). HTTP-based tests performed
by Willy Tarreau have shown performance improvements.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework mvneta_tx() so that the code that performs the final handling
before a sk_buff is transmitted is done only if the numbers of fragments
processed if positive.
This is preparation work to add the support for software TSO.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to ease the addition of new features, let's factorize the
feature list.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the introduction of of_phy_register_fixed_link(), this patch
introduces fixed link support in the mvneta driver, for Marvell Armada
370/XP SOCs.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following commit:
commit 9ec36cafe4
Author: Rob Herring <robh@kernel.org>
Date: Wed Apr 23 17:57:41 2014 -0500
of/irq: do irq resolution in platform_get_irq
changed platform_get_irq() which now returns EINVAL and EPROBE_DEFER,
in addition to ENXIO. If there's no interrupt for mvmdio, platform_get_irq()
returns EINVAL, but we currently check only for ENXIO.
Fix this by looking for a positive integer, which is the proper way of
validating a virtual interrupt number.
While at it, add a proper handling for the deferral probe case.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5445eaf309 ('mvneta: Try to fix mvneta when compiled as
module') fixed the mvneta driver to make it work properly when loaded
as a module in SGMII configuration, which was tested successful by the
author on the Armada XP OpenBlocks AX3, which uses SGMII.
However, some other platforms, namely the Armada XP GP don't use
SGMII, but a QSGMII connection between the MAC and the PHY, and this
case was not supported by the mvneta driver, which was relying on
configuration put in place by the bootloader. While this works when
the mvneta driver is built-in (because clocks are not gated), it
breaks when mvneta is built as a module, because the clock is gated
(all configuration is lost) and then re-enabled when the mvneta driver
is loaded.
In order to support all of RGMII, SGMII and QSGMII, this commit
reworks how the PHY interface configuration is done, and simplifies
it: it removes the mvneta_port_sgmii_config() and
mvneta_gmac_rgmii_set() functions, which were strange because
mvneta_gmac_rgmii_set() was called in all cases, even for SGMII
configurations. Also, the mvneta_gmac_rgmii_set() function was taking
a boolean as argument, which was always true.
Instead, all the PHY interface configuration logic is moved into the
mvneta_port_power_up() function, in a much simpler 'switch' construct,
with four cases:
- QSGMII: the RGMIIEn bit, the PCSEn bit in GMAC_CTRL_2 are set, and
the SERDES is configured in QSGMII. Technically speaking,
configuring the SERDES of the first port would be sufficient, but
it is simpler to do it on all ports.
- SGMII: the RGMIIEn bit, the PCSEn bit in GMAC_CTRL_2 are set, and
the SERDES is configured as SGMII.
- RGMII: the RGMIIEn bit in GMAC_CTRL_2 is set. The PCSEn bit is kept
cleared, and no SERDES configuration is done, because RGMII is not
using SERDES lanes.
- other: an error is returned. For this reason, the
mvneta_port_power_up() now returns an int instead of nothing, and
the return value is checked by mvneta_probe().
This has been successfully tested on:
* Armada XP DB, which has two RGMII and two SGMII connections
* Armada XP GP, which uses QSGMII for its four interfaces
* Armada 370 Mirabox, which has two RGMII connections
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit e3a8786c10. While
this commit allows to use the mvneta driver as a module on some
configurations, it breaks other configurations even if mvneta is used
built-in.
This breakage is due to the fact that on some RGMII platforms, the PCS
bit has to be set, and on some other platforms, it has to be
cleared. At the moment, we lack informations to know exactly the
significance of this bit (the datasheet only says "enables PCS"), and
so we can't produce a patch that will work on all platforms at this
point. And since this change is breaking the network completely for
many users, it's much better to revert it for now. We'll come back
later with a proper fix that takes into account all platforms.
Basically:
* Armada XP GP is configured as RGMII-ID, and needs the PCS bit to be
set.
* Armada 370 Mirabox is configured as RGMII-ID, and needs the PCS bit
to be cleared.
And at the moment, we don't know how to make the distinction between
those two cases. One hint is that the Armada XP GP appears in fact to
be using a QSGMII connection with the PHY (Quad-SGMII), but
configuring it as SGMII doesn't work, while RGMII-ID works. This needs
more investigation, but in the mean time, let's unbreak the network
for all those users.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reported-by: Arnaud Ebalard <arno@natisbad.org>
Reported-by: Alexander Reuter <Alexander.Reuter@gmx.net>
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=73401
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver currently uses of_iomap(), which has two drawbacks:
it doesn't request the resource, and it isn't devm-style so some error
handling is needed.
This commit switches to use devm_ioremap_resource() instead, which
automatically requests the resource (so the I/O registers region shows
up properly in /proc/iomem), and also is devm-style, which allows to
get rid of some error handling to unmap the I/O registers region.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
orion_mdio_reset() does nothing useful and is optional for the MDIO bus
code, so let's just remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver currently uses of_iomap(), which has two drawbacks:
it doesn't request the resource, and it isn't devm-style so some error
handling is needed.
This commit switches to use devm_ioremap_resource() instead, which
automatically requests the resource (so the I/O registers region shows
up properly in /proc/iomem), and also is devm-style, which allows to
get rid of some error handling to unmap the I/O registers region.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5445eaf309 ('mvneta: Try to fix mvneta when compiled as
module') fixed the mvneta driver to make it work properly when loaded
as a module in SGMII configuration, which was tested successful by the
author on the Armada XP OpenBlocks AX3, which uses SGMII.
However, it turns out that the Armada XP GP, which uses RGMII, is
affected by a similar problem: its SERDES configuration is lost when
mvneta is loaded as a module, because this configuration is set by the
bootloader, and then lost because the clock is gated by the clock
framework until the mvneta driver is loaded again and the clock is
re-enabled.
However, it turns out that for the RGMII case, setting the SERDES
configuration is not sufficient: the PCS enable bit in the
MVNETA_GMAC_CTRL_2 register must also be set, like in the SGMII
configuration.
Therefore, this commit reworks the SGMII/RGMII initialization: the
only difference between the two now is a different SERDES
configuration, all the rest is identical.
In detail, to achieve this, the commit:
* Renames MVNETA_SGMII_SERDES_CFG to MVNETA_SERDES_CFG because it is
not specific to SGMII, but also used on RGMII configurations.
* Adds a MVNETA_RGMII_SERDES_PROTO definition, that must be used as
the MVNETA_SERDES_CFG value in RGMII configurations.
* Removes the mvneta_gmac_rgmii_set() and mvneta_port_sgmii_config()
functions, and instead directly do the SGMII/RGMII configuration in
mvneta_port_up(), from where those functions where called. It is
worth mentioning that mvneta_gmac_rgmii_set() had an 'enable'
parameter that was always passed as '1', so it was pretty useless.
* Reworks the mvneta_port_up() function to set the MVNETA_SERDES_CFG
register to the appropriate value depending on the RGMII vs. SGMII
configuration. It also unconditionally set the PCS_ENABLE bit (was
already done for SGMII, but is now also needed for RGMII), and sets
the PORT_RGMII bit (which was already done for both SGMII and
RGMII).
This commit was successfully tested with mvneta compiled as a module,
on both the OpenBlocks AX3 (SGMII configuration) and the Armada XP GP
(RGMII configuration).
Reported-by: Steve McIntyre <steve@einval.com>
Cc: stable@vger.kernel.org # 3.11.x: 5445eaf309 mvneta: Try to fix mvneta when compiled as module
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bit 3 of the MVNETA_GMAC_CTRL_2 is actually used to enable the PCS,
not the PSC: there was a typo in the name of the define, which this
commit fixes.
Cc: stable@vger.kernel.org
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_kfree_skb_any in sky2_xmit_frame that
can be called in hard irq and other contexts.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_kfree_skb_any skge_xmit_free that can
be called in hard irq and other contexts, on the path that
handles dropped packets.
Replace dev_kfree_skb with dev_consume_skb_any in skge_tx_done that can
be called in hard irq and other contexts, on the path that handles
successfully transmitted skbs.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Replace dev_kfree_skb with dev_kfree_skb_any in mv643xx_eth_xmit and
txq_submit_skb that can be called in hard irq and other contexts,
on paths where the skbs are dropped.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Processing any incoming packets with a with a napi budget of 0
is incorrect driver behavior.
This matters as netpoll will shortly call drivers with a budget of 0
to avoid receive packet processing happening in hard irq context.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace the bh safe variant with the hard irq safe variant.
We need a hard irq safe variant to deal with netpoll transmitting
packets from hard irq context, and we need it in most if not all of
the places using the bh safe variant.
Except on 32bit uni-processor the code is exactly the same so don't
bother with a bh variant, just have a hard irq safe variant that
everyone can use.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver reads the mac address from the device registers which would
need to have been programmed by the bootloader. This patch adds
the ability to pull the mac from devicetree via the pci device dt node.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Cc: netdev@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Changes since v2:
- eliminated use of stack tmpaddr per feedback
Changes since v1:
- simplified based on feedback
- fixed formatting
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_3ad.h
drivers/net/bonding/bond_main.c
Two minor conflicts in bonding, both of which were overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
With the introduction of the support for Armada 375 and Armada 38x,
the hidden Kconfig option MACH_ARMADA_370_XP is being renamed to
MACH_MVEBU_V7. Therefore, the dependency that was used for the mvneta
driver can no longer work. This commit replaces this dependency by a
dependency on PLAT_ORION, which is used similarly for the mv643xx_eth
driver.
In addition to this, it takes this opportunity to adjust the
description and help text to indicate that the driver can is also used
for Armada 38x. Note that Armada 375 cannot use this driver as it has
a completely different networking unit, which will require a separate
driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are many drivers calling alloc_percpu() to allocate pcpu stats
and then initializing ->syncp. So just introduce a helper function for them.
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function return parameter is not used in mvneta_tx_done_gbe(),
where the function is called. This patch makes the function return
void.
Reviewed-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mvneta_tx_done_gbe() return value and third parameter are no more
used. This patch changes the function prototype and removes a useless
variable where the function is called.
Reviewed-by: Willy Tarreau <w@1wt.eu>
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thomas Fitzsimmons