Sparse noticed a locking imbalance in tg3_open(). This patch adds an
unlock to one of the error paths, so that tg3_open() always exits
without the lock held.
Signed-off-by: Ira W. Snyder <kernel@irasnyder.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to hardware errata, TSO must be disabled if the PCI Express clock
request is enabled on 5906. The chip may hang when transmitting TSO
frames if CLKREQ is enabled.
Update version to 3.69.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer 5906 bootcode needs about 7ms to finish resetting so the poll
firmware loop was changed to maximum 20ms.
Signed-off-by: Gary Zambrano <zambrano@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the next descriptor array entry cannot be allocated by dev_alloc_skb(),
return immediately so it is not dereferenced later. We cannot register the
device with a partial descriptor list.
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: David Rientjes <rientjes@cs.washington.edu>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
com20020.c needs to export functions if either of the ISA or PCI modules
are built as loadable modules. Or they could always be exported.
WARNING: "com20020_found" [drivers/net/arcnet/com20020-pci.ko] undefined!
WARNING: "com20020_check" [drivers/net/arcnet/com20020-pci.ko] undefined!
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Toralf Forster <toralf.foerster@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Coverity checker noted that these "if (err)"'s couldn't ever be
true.
It seems the intention was to check the return values of the
bcm43xx_pci_write_config32()'s?
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drain the Microcode TX-status-FIFO before we enable IRQs.
This is required, because the FIFO may still have entries left
from a previous run. Those would immediately fire after enabling
IRQs and would lead to an oops in the DMA TXstatus handling code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use proper upper limits for the loops and check for all error
conditions.
The problem was noticed by Adrian Bunk.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As Patrick McHardy <kaber@trash.net> suggested, Traffic Shaper is now
obsolete and alternative to it is no longer CBQ, since its problems with
virtual devices, alter Kconfig text to reflect this -- put a link to the
traffic schedulers as a whole.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
e1000: Fix suspend/resume powerup and irq allocation
From: Auke Kok <auke-jan.h.kok@intel.com>
After 7.0.33/2.6.16, e1000 suspend/resume left the user with an enabled
device showing garbled statistics and undetermined irq allocation state,
where `ifconfig eth0 down` would display `trying to free already freed irq`.
Explicitly free and allocate irq as well as powerup the PHY during resume
fixes when needed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Through some experimentation with the similarly built bcm43xx I came to
the conclusion that if the hw/firmware sets a bit in the interrupt
register, an interrupt will only be raised if that bit is included in
the interrupt mask. Hence, the interrupt mask is more like an interrupt
control mask.
This patch changes the comment to reflect that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/Kconfig says:
# All the following symbols are dependent on NETDEVICES - do not repeat
# that for each of the symbols.
so remove duplicate 'depends' uses of NETDEVICES.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes 64k page support by using PAGE_MASK and appropriate pagesize defines in several places.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Removed define H_CB_ALIGNMENT which is already defined in include/asm-powerpc/hvcall.h
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix: Must check for nullpointer before dereferencing it - not afterwards.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes a bug reported in:
http://bugzilla.kernel.org/show_bug.cgi?id=7438
tg3_close() turns off the PHY if WoL and ASF are both disabled. On
the next tg3_open(), some devices such as the 5752M will not be
brought up correctly without a PHY reset early in the reset sequence.
The PHY clock is needed for some internal MAC blocks to function
correctly.
This problem is fixed by always resetting the PHY early in
tg3_reset_hw() when it is called from tg3_open() or tg3_resume().
tg3_setup_phy() can then be called later in the sequence without the
reset_phy parameter set to 1, since the PHY reset is already done.
Update version to 3.68.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bcm43xx driver uses 4 locations in the devices sprom to determine
the behavior of the leds. Certain defaults are assigned if all bits are
set in those locations. On at least one BCM4303 chip, the sprom contains
values other than the default, which executes an assertion placed in the
default case of a following switch statement. This patch makes the leds
on the above mentioned interface behave correctly. In addition, it limits
the number of logged messages to 20 for the case of unexpected values in
the sprom locations.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes a netdev watchdog timeout problem.
The software needs to call netif_tx_disable before running the
hardware calibration code. The problem condition can be shown by the
following timegraph.
|---5secs - ~10 jiffies time---|---|OOPS
^ ^
last real TX periodic work stops netif
At OOPS, the following happens:
The watchdog timer triggers, because the timeout of 5secs
is over. The watchdog first checks for stopped TX.
_Usually_ TX is only stopped from the TX handler to indicate
a full TX queue. But this is different. We need to stop TX here,
regardless of the TX queue state. So the watchdog recognizes
the stopped device and assumes it is stopped due to full
TX queues (Which is a _wrong_ assumption in this case). It then
tests how far the last TX has been in the past. If it's more than
5secs (which is the case for low or no traffic), it will fire
a TX timeout.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The length of the manfid CIS should be at least 4, and it's normally 4.
It's incorrect to require it to be at least 5. This breaks support for
most (if not all) cards.
The right place to ensure that we don't access beyond the CIS buffer is
to strengthen another check. Make sure that the next tuple begins at
least at the CIS buffer end (in which case we stop processing) or
before that.
Reported by ph35sm@free.fr
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The sky2 driver uses a single NAPI poll routine for both ports on dual ported
cards (because there is a single IRQ and status ring). Netpoll makes assumptions
about the relationship between network device and NAPI that aren't correct
on the second port, this will cause the port to never clear work.
Most systems, just have single port, so not a big issue.
The easy fix is just make the second port, not netpoll capable.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I don't want my code to downgraded to GPLv3 because of
cut-n-pasted the comments. These files which I hold copyright
on were started before it was clear what GPLv3 was going to be.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Checks for NULL dev_alloc_skb() and returns on true to avoid subsequent
dereference.
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Christoph Hellwig <hch@infrared.org>
Signed-off-by: David Rientjes <rientjes@cs.washington.edu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
No need to keep defining PCI_DEVICE_ID_SERVERWORKS_HT2000_PCIE
in the driver code since it is now defined in pci_ids.h.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sky2 driver is no longer in experimental state.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
modprobe n2 with no parameters or no such devices
will get confusing error message.
# modprobe n2
... Kernel does not have module support
This patch replaces return code from -ENOSYS to -EINVAL.
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
drivers/net/wan/n2.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- Call platform_driver_unregister() before return when no cards found.
(fixes data corruption when no cards found)
- Check platform_device_register_simple() return value
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Mike Phillips <mikep@linuxtr.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
drivers/net/tokenring/proteon.c | 9 +++++++--
drivers/net/tokenring/skisa.c | 9 +++++++--
2 files changed, 14 insertions(+), 4 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Flooding the console with error messages for every RX FIFO overrun,
checksum error and framing error isn't very sensible. Each of these
errors can occur during normal operation, so stop printk'ing error
messages for RX errors at all.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Ray Lehtiniemi reported that an incoming UDP packet flood can lock up
the ep93xx ethernet driver. Herbert Valerio Riedel noted that due to
the way ep93xx_eth manages the RX/TXstatus rings, it cannot distinguish
a full ring from an empty one, and correctly suggested that this was
likely to be causing this lockup to occur.
Instead of looking at the hardware's RX/TXstatus ring write pointers
to determine when to stop reading from those rings, we should just check
every individual RX/TXstatus descriptor's valid bit instead, since there
is no other way to distinguish an empty ring from a full ring, and if
there is a descriptor waiting, we take the hit of reading the descriptor
from memory anyway.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Wed, 25 Oct 2006 18:03:13 +0200 Toralf Förster wrote:
> WARNING: "arp_broken_ops" [drivers/net/wan/sealevel.ko] undefined!
> make[1]: *** [__modpost] Error 1
> make: *** [modules] Error 2
>
> Here's the config:
...
> # CONFIG_INET is not set
> CONFIG_SEALEVEL_4021=m
Sealevel uses arp_broken_ops so it needs to depend on INET.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a2b98a697f.
As per Guennadi Liakhovetski, the mac address change support code breaks
some normal uses (_without_ any address changes), and until it's all
sorted out, we're better off without it.
Says Francois:
"Go revert it.
Despite what I claimed, I can not find a third-party confirmation by
email that it works elsewhere.
It would probably be enough to remove the call to
__rtl8169_set_mac_addr() in rtl8169_hw_start() though."
See also
http://bugzilla.kernel.org/show_bug.cgi?id=6032
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As a replacement for the broad manufactor/card ID match we commented out
because of conflicts with pcnet_cs, add two product ID matches.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
CRYPTO_MANAGER is selected automatically by CONFIG_ECB and CONFIG_CBC.
config CRYPTO_ECB
tristate "ECB support"
select CRYPTO_BLKCIPHER
select CRYPTO_MANAGER
I've added CONFIG_ECB to the ones you mentioned and CONFIG_CBC to
gssapi.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Account for the interface being closed before disabling polling
on a device, to fix shutdown on some systems that explcitly close
the netdevice before calling shutdown.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Move the length (rx_bytes counter) adjustment of 4 bytes down to after the
TBI_ACCEPT workaround.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
82571 and newer chispets don't need to limit desc. length to 4kb and can
handle 8kb sizes.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Allocations using alloc_page are taking too long for normal MTU, so
use LPE only for jumbo frames.
Signed-off-bu: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Threshold bitmasks for prefetch, host and writeback were clearing
bits that they were not supposed to. The leftmost 2 bits in the byte
for each threshold are reserved.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
The MANC register should not be read for PCI-E adapters at all, as well as
82543 and older where 82543 would master abort when this register was
accessed.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Ira W. Snyder