Callers hold rcu_read_lock(), so we do not need
the rcu_read_lock()/rcu_read_unlock() pair.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet6_ifa_finish_destroy() already uses kfree_rcu() to free
inet6_ifaddr structs.
We need to use proper list additions/deletions in order
to allow readers to use RCU instead of idev->lock rwlock.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ido reported following splat and provided a patch.
[ 122.221814] BUG: using smp_processor_id() in preemptible [00000000] code: sshd/2672
[ 122.221845] caller is debug_smp_processor_id+0x17/0x20
[ 122.221866] CPU: 0 PID: 2672 Comm: sshd Not tainted 4.14.0-rc3-idosch-next-custom #639
[ 122.221880] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016
[ 122.221893] Call Trace:
[ 122.221919] dump_stack+0xb1/0x10c
[ 122.221946] ? _atomic_dec_and_lock+0x124/0x124
[ 122.221974] ? ___ratelimit+0xfe/0x240
[ 122.222020] check_preemption_disabled+0x173/0x1b0
[ 122.222060] debug_smp_processor_id+0x17/0x20
[ 122.222083] ip6_pol_route+0x1482/0x24a0
...
I believe we can simplify this code path a bit, since we no longer
hold a read_lock and need to release it to avoid a dead lock.
By disabling BH, we make sure we'll prevent code re-entry and
rt6_get_pcpu_route()/rt6_make_pcpu_route() run on the same cpu.
Fixes: 66f5d6ce53 ("ipv6: replace rwlock with rcu and spinlock in fib6_table")
Reported-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When gso_size reset to zero for the tail segment in skb_segment(), later
in ipv6_gso_segment(), __skb_udp_tunnel_segment() and gre_gso_segment()
we will get incorrect results (payload length, pcsum) for that segment.
inet_gso_segment() already has a check for gso_size before calculating
payload.
The issue was found with LTP vxlan & gre tests over ixgbe NIC.
Fixes: 07b26c9454 ("gso: Support partial splitting at the frag_list pointer")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 35e015e1f5 ("ipv6: fix net.ipv6.conf.all interface DAD handlers")
was intended to affect accept_dad flag handling in such a way that
DAD operation and mode on a given interface would be selected
according to the maximum value of conf/{all,interface}/accept_dad.
However, addrconf_dad_begin() checks for particular cases in which we
need to skip DAD, and this check was modified in the wrong way.
Namely, it was modified so that, if the accept_dad flag is 0 for the
given interface *or* for all interfaces, DAD would be skipped.
We have instead to skip DAD if accept_dad is 0 for the given interface
*and* for all interfaces.
Fixes: 35e015e1f5 ("ipv6: fix net.ipv6.conf.all interface DAD handlers")
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Reported-by: Erik Kline <ek@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, most of the rt6_stats are not hooked up correctly. As the
last part of this patch series, hook up all existing rt6_stats and add
one new stat fib_rt_uncache to indicate the number of routes in the
uncached list.
For details of the stats, please refer to the comments added in
include/net/ip6_fib.h.
Note: fib_rt_alloc and fib_rt_uncache are not guaranteed to be modified
under a lock. So atomic_t is used for them.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With all the preparation work before, we are now ready to replace rwlock
with rcu and spinlock in fib6_table.
That means now all fib6_node in fib6_table are protected by rcu. And
when freeing fib6_node, call_rcu() is used to wait for the rcu grace
period before releasing the memory.
When accessing fib6_node, corresponding rcu APIs need to be used.
And all previous sessions protected by the write lock will now be
protected by the spin lock per table.
All previous sessions protected by read lock will now be protected by
rcu_read_lock().
A couple of things to note here:
1. As part of the work of replacing rwlock with rcu, the linked list of
fn->leaf now has to be rcu protected as well. So both fn->leaf and
rt->dst.rt6_next are now __rcu tagged and corresponding rcu APIs are
used when manipulating them.
2. For fn->rr_ptr, first of all, it also needs to be rcu protected now
and is tagged with __rcu and rcu APIs are used in corresponding places.
Secondly, fn->rr_ptr is changed in rt6_select() which is a reader
thread. This makes the issue a bit complicated. We think a valid
solution for it is to let rt6_select() grab the tb6_lock if it decides
to change it. As it is not in the normal operation and only happens when
there is no valid neighbor cache for the route, we think the performance
impact should be low.
3. fib6_walk_continue() has to be called with tb6_lock held even in the
route dumping related functions, e.g. inet6_dump_fib(),
fib6_tables_dump() and ipv6_route_seq_ops. It is because
fib6_walk_continue() makes modifications to the walker structure, and so
are fib6_repair_tree() and fib6_del_route(). In order to do proper
syncing between them, we need to let fib6_walk_continue() hold the lock.
We may be able to do further improvement on the way we do the tree walk
to get rid of the need for holding the spin lock. But not for now.
4. When fib6_del_route() removes a route from the tree, we no longer
mark rt->dst.rt6_next to NULL to make simultaneous reader be able to
further traverse the list with rcu. However, rt->dst.rt6_next is only
valid within this same rcu period. No one should access it later.
5. All the operation of atomic_inc(rt->rt6i_ref) is changed to be
performed before we publish this route (either by linking it to fn->leaf
or insert it in the list pointed by fn->leaf) just to be safe because as
soon as we publish the route, some read thread will be able to access it.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After rwlock is replaced with rcu and spinlock, fib6_lookup() could
potentially return an intermediate node if other thread is doing
fib6_del() on a route which is the only route on the node so that
fib6_repair_tree() will be called on this node and potentially assigns
fn->leaf to the its child's fn->leaf.
In order to detect this situation in rt6_select(), we have to check if
fn->fn_bit is consistent with the key length stored in the route. And
depending on if the fn is in the subtree or not, the key is either
rt->rt6i_dst or rt->rt6i_src.
If any inconsistency is found, that means the node no longer holds valid
routes in it. So net->ipv6.ip6_null_entry is returned.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If rwlock is replaced with rcu and spinlock, it is possible that the
reader thread will see fn->leaf as NULL in the following scenarios:
1. fib6_add() is in progress and we have already inserted a new node but
not yet inserted the route.
2. fib6_del_route() is in progress and we have already set fn->leaf to
NULL but not yet freed the node because of rcu grace period.
This patch makes sure all the reader threads check fn->leaf first before
using it. And together with later patch to grab rcu_read_lock() and
rcu_dereference() fn->leaf, it makes sure reader threads are safe when
accessing fn->leaf.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib6_add() logic currently calls fib6_add_1() to figure out what node
should be used for the newly added route and then call
fib6_add_rt2node() to insert the route to the node.
And during the call of fib6_add_1(), fn_sernum is updated for all nodes
that share the same prefix as the new route.
This does not have issue in the current code because reader thread will
not be able to access the tree while writer thread is inserting new
route to it. However, it is not the case once we transition to use RCU.
Reader thread could potentially see the new fn_sernum before the new
route is inserted. As a result, reader thread's route lookup will return
a stale route with the new fn_sernum.
In order to solve this issue, we remove all the update of fn_sernum in
fib6_add_1(), and instead, introduce a new function that updates fn_sernum
for all related nodes and call this functions once the route is
successfully inserted to the tree.
Also, smp_wmb() is used after a route is successfully inserted into the
fib tree and right before the updated of fn->sernum. And smp_rmb() is
used right after fn->sernum is accessed in rt6_get_cookie_safe(). This
is to guarantee that when the reader thread sees the new fn->sernum, the
new route is already inserted in the tree in memory.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With rwlock, it is safe to call dst_hold() in the read thread because
read thread is guaranteed to be separated from write thread.
However, after we replace rwlock with rcu, it is no longer safe to use
dst_hold(). A dst might already have been deleted but is waiting for the
rcu grace period to pass before freeing the memory when a read thread is
trying to do dst_hold(). This could potentially cause double free issue.
So this commit replaces all dst_hold() with dst_hold_safe() in all read
thread to avoid this double free issue.
And in order to make the code more compact, a new function ip6_hold_safe()
is introduced. It calls dst_hold_safe() first, and if that fails, it will
either fall back to hold and return net->ipv6.ip6_null_entry or set rt to
NULL according to the caller's need.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After rwlock is replaced with rcu and spinlock, route lookup can happen
simultanously with route deletion.
This patch removes the call to free_percpu(rt->rt6i_pcpu) from
rt6_release() to avoid the race condition between rt6_release() and
rt6_get_pcpu_route(). And as free_percpu(rt->rt6i_pcpu) is already
called in ip6_dst_destroy() after the rcu grace period, it is safe to do
this change.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After rwlock is replaced with rcu and spinlock, ip6_pol_route() will be
called with only rcu held. That means rt6 route deletion could happen
simultaneously with rt6_make_pcpu_rt(). This could potentially cause
memory leak if rt6_release() is called right before rt6_make_pcpu_rt()
on the same route.
This patch grabs rt->rt6i_ref safely before calling rt6_make_pcpu_rt()
to make sure rt6_release() will not get triggered while
rt6_make_pcpu_rt() is in progress. And rt6_release() is called after
rt6_make_pcpu_rt() is finished.
Note: As we are incrementing rt->rt6i_ref in ip6_pol_route(), there is a
very slim chance that fib6_purge_rt() will be triggered unnecessarily
when deleting a route if ip6_pol_route() running on another thread picks
this route as well and tries to make pcpu cache for it.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit makes use of the exception hash table implementation to
store dst caches created by pmtu discovery and ip redirect into the hash
table under the rt_info and no longer inserts these routes into fib6
tree.
This makes the fib6 tree only contain static configured routes and could
now be protected by rcu instead of a rw lock.
With this change, in the route lookup related functions, after finding
the rt6_info with the longest prefix, we also need to search for the
exception table before doing backtracking.
In the route delete function, if the route being deleted is not a dst
cache, deletion of this route also need to flush the whole hash table
under it. If it is a dst cache, then only delete the cached dst in the
hash table.
Note: for fib6_walk_continue() function, w->root now is always pointing
to a root node considering that fib6_prune_clones() is removed from the
code. So we add a WARN_ON() msg to make sure w->root always points to a
root node and also removed the update of w->root in fib6_repair_tree().
This is a prerequisite for later patch because we don't need to make
w->root as rcu protected when replacing rwlock with RCU.
Also, we remove all prune related variables as it is no longer used.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib6_locate() is used to find the fib6_node according to the passed in
prefix address key. It currently tries to find the fib6_node with the
exact match of the passed in key. However, when we move cached routes
into the exception table, fib6_locate() will fail to find the fib6_node
for it as the cached routes will be stored in the exception table under
the fib6_node with the longest prefix match of the cache's dst addr key.
This commit adds a new parameter to let the caller specify if it needs
exact match or longest prefix match.
Right now, all callers still does exact match when calling
fib6_locate(). It will be changed in later commit where exception table
is hooked up to store cached routes.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If all dst cache entries are stored in the exception table under the
main route, we have to go through them during fib6_age() when doing
garbage collecting.
Introduce a new function rt6_age_exception() which goes through all dst
entries in the exception table and remove those entries that are expired.
This function is called in fib6_age() so that all dst caches are also
garbage collected.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we move all cached dst into the exception table under the main route,
current rt6_clean_tohost() will no longer be able to access them.
This commit makes fib6_clean_tohost() to also go through all cached
routes in exception table and removes cached gateway routes to the
passed in gateway.
This is a preparation in order to move all cached routes into the
exception table.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we move all cached dst into the exception table under the main route,
current rt6_mtu_change() will no longer be able to access them.
This commit makes rt6_mtu_change_route() function to also go through all
cached routes in the exception table under the main route and do proper
updates on the mtu.
This is a preparation in order to move all cached routes into the
exception table.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After we move cached dst entries into the exception table under its
parent route, current fib6_remove_prefsrc() no longer can access them.
This commit makes fib6_remove_prefsrc() also go through all routes
in the exception table to remove the pref src.
This is a preparation patch in order to move all cached dst into the
exception table.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a hash table into struct rt6_info in order to store dst caches
created by pmtu discovery and ip redirect in ipv6 routing code.
APIs to add dst cache, delete dst cache, find dst cache and update
dst cache in the hash table are implemented and will be used in later
commits.
This is a preparation work to move all cache routes into the exception
table instead of getting inserted into the fib6 tree.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function takes a route as input and tries to update the sernum in
the fib6_node this route is associated with. It will be used in later
commit when adding a cached route into the exception table under that
route.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit cc71b7b071 ("net/ipv6: remove unused err variable on
icmpv6_push_pending_frames") exposed icmpv6_push_pending_frames
return value not being used.
Remove now unnecessary int err declarations and uses.
Miscellanea:
o Remove unnecessary goto and out: labels
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
int err is unused by icmpv6_push_pending_frames(), this patch returns removes the variable and returns the function with 0.
git bisect shows this variable has been around since linux has been in git in commit 1da177e4c3.
This was found by running make coccicheck M=net/ipv6/ on linus' tree on commit 77ede3a014 (current HEAD as of this patch).
Signed-off-by: Tim Hansen <devtimhansen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Storing the left length of skb into 'len' actually has no effect
so we can remove it.
Signed-off-by: Lin Zhang <xiaolou4617@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when updating mtu in tx path, it doesn't consider ARPHRD_ETHER tunnel
device, like ip6gre_tap tunnel, for which it should also subtract ether
header to get the correct mtu.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch 'ip_gre: ipgre_tap device should keep dst' fixed
a issue that ipgre_tap mtu couldn't be updated in tx path.
The same fix is needed for ip6gre_tap as well.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far we've been relying on sockopt(SOL_IP, IP_FREEBIND) being usable
even on IPv6 sockets.
However, it turns out it is perfectly reasonable to want to set freebind
on an AF_INET6 SOCK_RAW socket - but there is no way to set any SOL_IP
socket option on such a socket (they're all blindly errored out).
One use case for this is to allow spoofing src ip on a raw socket
via sendmsg cmsg.
Tested:
built, and booted
# python
>>> import socket
>>> SOL_IP = socket.SOL_IP
>>> SOL_IPV6 = socket.IPPROTO_IPV6
>>> IP_FREEBIND = 15
>>> IPV6_FREEBIND = 78
>>> s = socket.socket(socket.AF_INET6, socket.SOCK_DGRAM, 0)
>>> s.getsockopt(SOL_IP, IP_FREEBIND)
0
>>> s.getsockopt(SOL_IPV6, IPV6_FREEBIND)
0
>>> s.setsockopt(SOL_IPV6, IPV6_FREEBIND, 1)
>>> s.getsockopt(SOL_IP, IP_FREEBIND)
1
>>> s.getsockopt(SOL_IPV6, IPV6_FREEBIND)
1
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NS for DAD are sent on admin up as long as a valid qdisc is found.
A race condition exists by which these packets will not egress the
interface if the operational state of the lower device is not yet up.
The solution is to delay DAD until the link is operationally up
according to RFC2863. Rather than only doing this, follow the existing
code checks by deferring IPv6 device initialization altogether. The fix
allows DAD on devices like tunnels that are controlled by userspace
control plane. The fix has no impact on regular deployments, but means
that there is no IPv6 connectivity until the port has been opened in
the case of port-based network access control, which should be
desirable.
Signed-off-by: Mike Manning <mmanning@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When running LTP IPsec tests, KASan might report:
BUG: KASAN: use-after-free in vti_tunnel_xmit+0xeee/0xff0 [ip_vti]
Read of size 4 at addr ffff880dc6ad1980 by task swapper/0/0
...
Call Trace:
<IRQ>
dump_stack+0x63/0x89
print_address_description+0x7c/0x290
kasan_report+0x28d/0x370
? vti_tunnel_xmit+0xeee/0xff0 [ip_vti]
__asan_report_load4_noabort+0x19/0x20
vti_tunnel_xmit+0xeee/0xff0 [ip_vti]
? vti_init_net+0x190/0x190 [ip_vti]
? save_stack_trace+0x1b/0x20
? save_stack+0x46/0xd0
dev_hard_start_xmit+0x147/0x510
? icmp_echo.part.24+0x1f0/0x210
__dev_queue_xmit+0x1394/0x1c60
...
Freed by task 0:
save_stack_trace+0x1b/0x20
save_stack+0x46/0xd0
kasan_slab_free+0x70/0xc0
kmem_cache_free+0x81/0x1e0
kfree_skbmem+0xb1/0xe0
kfree_skb+0x75/0x170
kfree_skb_list+0x3e/0x60
__dev_queue_xmit+0x1298/0x1c60
dev_queue_xmit+0x10/0x20
neigh_resolve_output+0x3a8/0x740
ip_finish_output2+0x5c0/0xe70
ip_finish_output+0x4ba/0x680
ip_output+0x1c1/0x3a0
xfrm_output_resume+0xc65/0x13d0
xfrm_output+0x1e4/0x380
xfrm4_output_finish+0x5c/0x70
Can be fixed if we get skb->len before dst_output().
Fixes: b9959fd3b0 ("vti: switch to new ip tunnel code")
Fixes: 22e1b23daf ("vti6: Support inter address family tunneling.")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR() already implies unlikely(), so it can be omitted.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipv6_skip_exthdr, the lengh of AH header is computed manually
as (hp->hdrlen+2)<<2. However, in include/linux/ipv6.h, a macro
named ipv6_authlen is already defined for exactly the same job. This
commit replaces the manual computation code with the macro.
Signed-off-by: Xiang Gao <qasdfgtyuiop@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, writing into
net.ipv6.conf.all.{accept_dad,use_optimistic,optimistic_dad} has no effect.
Fix handling of these flags by:
- using the maximum of global and per-interface values for the
accept_dad flag. That is, if at least one of the two values is
non-zero, enable DAD on the interface. If at least one value is
set to 2, enable DAD and disable IPv6 operation on the interface if
MAC-based link-local address was found
- using the logical OR of global and per-interface values for the
optimistic_dad flag. If at least one of them is set to one, optimistic
duplicate address detection (RFC 4429) is enabled on the interface
- using the logical OR of global and per-interface values for the
use_optimistic flag. If at least one of them is set to one,
optimistic addresses won't be marked as deprecated during source address
selection on the interface.
While at it, as we're modifying the prototype for ipv6_use_optimistic_addr(),
drop inline, and let the compiler decide.
Fixes: 7fd2561e4e ("net: ipv6: Add a sysctl to make optimistic addresses useful candidates")
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit f784ad3d79 ("ipv6: do not send RTM_DELADDR for tentative
addresses") incorrectly assumes that no RTM_NEWADDR are sent for
addresses in tentative state, as this does happen for the standard
IPv6 use-case of DAD failure, see the call to ipv6_ifa_notify() in
addconf_dad_stop(). So as a result of this change, no RTM_DELADDR is
sent after DAD failure for a link-local when strict DAD (accept_dad=2)
is configured, or on the next admin down in other cases. The absence
of this notification breaks backwards compatibility and causes problems
after DAD failure if this notification was being relied on. The
solution is to allow RTM_DELADDR to still be sent after DAD failure.
Fixes: f784ad3d79 ("ipv6: do not send RTM_DELADDR for tentative addresses")
Signed-off-by: Mike Manning <mmanning@brocade.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having a global list of labels do not scale to thousands of
netns in the cloud era. This causes quadratic behavior on
netns creation and deletion.
This is time having a per netns list of ~10 labels.
Tested:
$ time perf record (for f in `seq 1 3000` ; do ip netns add tast$f; done)
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 3.637 MB perf.data (~158898 samples) ]
real 0m20.837s # instead of 0m24.227s
user 0m0.328s
sys 0m20.338s # instead of 0m23.753s
16.17% ip [kernel.kallsyms] [k] netlink_broadcast_filtered
12.30% ip [kernel.kallsyms] [k] netlink_has_listeners
6.76% ip [kernel.kallsyms] [k] _raw_spin_lock_irqsave
5.78% ip [kernel.kallsyms] [k] memset_erms
5.77% ip [kernel.kallsyms] [k] kobject_uevent_env
5.18% ip [kernel.kallsyms] [k] refcount_sub_and_test
4.96% ip [kernel.kallsyms] [k] _raw_read_lock
3.82% ip [kernel.kallsyms] [k] refcount_inc_not_zero
3.33% ip [kernel.kallsyms] [k] _raw_spin_unlock_irqrestore
2.11% ip [kernel.kallsyms] [k] unmap_page_range
1.77% ip [kernel.kallsyms] [k] __wake_up
1.69% ip [kernel.kallsyms] [k] strlen
1.17% ip [kernel.kallsyms] [k] __wake_up_common
1.09% ip [kernel.kallsyms] [k] insert_header
1.04% ip [kernel.kallsyms] [k] page_remove_rmap
1.01% ip [kernel.kallsyms] [k] consume_skb
0.98% ip [kernel.kallsyms] [k] netlink_trim
0.51% ip [kernel.kallsyms] [k] kernfs_link_sibling
0.51% ip [kernel.kallsyms] [k] filemap_map_pages
0.46% ip [kernel.kallsyms] [k] memcpy_erms
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ipv6 has been disabled from cmdline since kernel started, it makes
no sense to allow users to create any ip6 tunnel. Otherwise, it could
some potential problem.
Jianlin found a kernel crash caused by this in ip6_gre when he set
ipv6.disable=1 in grub:
[ 209.588865] Unable to handle kernel paging request for data at address 0x00000080
[ 209.588872] Faulting instruction address: 0xc000000000a3aa6c
[ 209.588879] Oops: Kernel access of bad area, sig: 11 [#1]
[ 209.589062] NIP [c000000000a3aa6c] fib_rules_lookup+0x4c/0x260
[ 209.589071] LR [c000000000b9ad90] fib6_rule_lookup+0x50/0xb0
[ 209.589076] Call Trace:
[ 209.589097] fib6_rule_lookup+0x50/0xb0
[ 209.589106] rt6_lookup+0xc4/0x110
[ 209.589116] ip6gre_tnl_link_config+0x214/0x2f0 [ip6_gre]
[ 209.589125] ip6gre_newlink+0x138/0x3a0 [ip6_gre]
[ 209.589134] rtnl_newlink+0x798/0xb80
[ 209.589142] rtnetlink_rcv_msg+0xec/0x390
[ 209.589151] netlink_rcv_skb+0x138/0x150
[ 209.589159] rtnetlink_rcv+0x48/0x70
[ 209.589169] netlink_unicast+0x538/0x640
[ 209.589175] netlink_sendmsg+0x40c/0x480
[ 209.589184] ___sys_sendmsg+0x384/0x4e0
[ 209.589194] SyS_sendmsg+0xd4/0x140
[ 209.589201] SyS_socketcall+0x3e0/0x4f0
[ 209.589209] system_call+0x38/0xe0
This patch is to return -EOPNOTSUPP in ip6_tunnel_init if ipv6 has been
disabled from cmdline.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now in ip6gre_header before packing the ipv6 header, it skb_push t->hlen
which only includes encap_hlen + tun_hlen. It means greh and inner header
would be over written by ipv6 stuff and ipv6h might have no chance to set
up.
Jianlin found this issue when using remote any on ip6_gre, the packets he
captured on gre dev are truncated:
22:50:26.210866 Out ethertype IPv6 (0x86dd), length 120: truncated-ip6 -\
8128 bytes missing!(flowlabel 0x92f40, hlim 0, next-header Options (0) \
payload length: 8192) ::1:2000:0 > ::1:0:86dd: HBH [trunc] ip-proto-128 \
8184
It should also skb_push ipv6hdr so that ipv6h points to the right position
to set ipv6 stuff up.
This patch is to skb_push hlen + sizeof(*ipv6h) and also fix some indents
in ip6gre_header.
Fixes: c12b395a46 ("gre: Support GRE over IPv6")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While trying an ESP transport mode encryption for UDPv6 packets of
datagram size 1436 with MTU 1500, checksum error was observed in
the secondary fragment.
This error occurs due to the UDP payload checksum being missed out
when computing the full checksum for these packets in
udp6_hwcsum_outgoing().
Fixes: d39d938c82 ("ipv6: Introduce udpv6_send_skb()")
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In collect_md mode, if the tun dev is down, it still can call
__ip6_tnl_rcv to receive on packets, and the rx statistics increase
improperly.
When the md tunnel is down, it's not neccessary to increase RX drops
for the tunnel device, packets would be recieved on fallback tunnel,
and the RX drops on fallback device will be increased as expected.
Fixes: 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
Cc: Alexei Starovoitov <ast@fb.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As seg6_validate_srh() already checks that the Routing Header type is
correct, it is not necessary to do it again in get_srh().
Fixes: 5829d70b ("ipv6: sr: fix get_srh() to comply with IPv6 standard "RFC 8200")
Signed-off-by: David Lebrun <dlebrun@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar to vxlan/geneve tunnel, if hop_limit is zero, it should fall
back to ip6_dst_hoplimt().
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 FIB should use FIB6_TABLE_HASHSZ, not FIB_TABLE_HASHSZ.
Fixes: ba1cc08d94 ("ipv6: fix memory leak with multiple tables during netns destruction")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the cited commit fixed a possible deadlock, it added a leak
of the request socket, since reqsk_put() must be called if the BPF
filter decided the ACK packet must be dropped.
Fixes: d624d276d1 ("tcp: fix possible deadlock in TCP stack vs BPF filter")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for your net tree,
they are:
1) Fix SCTP connection setup when IPVS module is loaded and any scheduler
is registered, from Xin Long.
2) Don't create a SCTP connection from SCTP ABORT packets, also from
Xin Long.
3) WARN_ON() and drop packet, instead of BUG_ON() races when calling
nf_nat_setup_info(). This is specifically a longstanding problem
when br_netfilter with conntrack support is in place, patch from
Florian Westphal.
4) Avoid softlock splats via iptables-restore, also from Florian.
5) Revert NAT hashtable conversion to rhashtable, semantics of rhlist
are different from our simple NAT hashtable, this has been causing
problems in the recent Linux kernel releases. From Florian.
6) Add per-bucket spinlock for NAT hashtable, so at least we restore
one of the benefits we got from the previous rhashtable conversion.
7) Fix incorrect hashtable size in memory allocation in xt_hashlimit,
from Zhizhou Tian.
8) Fix build/link problems with hashlimit and 32-bit arches, to address
recent fallout from a new hashlimit mode, from Vishwanath Pai.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are reports about spurious softlockups during iptables-restore, a
backtrace i saw points at get_counters -- it uses a sequence lock and also
has unbounded restart loop.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
fib6_net_exit only frees the main and local tables. If another table was
created with fib6_alloc_table, we leak it when the netns is destroyed.
Fix this in the same way ip_fib_net_exit cleans up tables, by walking
through the whole hashtable of fib6_table's. We can get rid of the
special cases for local and main, since they're also part of the
hashtable.
Reproducer:
ip netns add x
ip -net x -6 rule add from 6003:1::/64 table 100
ip netns del x
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: 58f09b78b7 ("[NETNS][IPV6] ip6_fib - make it per network namespace")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when probessing ICMPV6_PKT_TOOBIG, ip6gre_err only subtracts the
offset of gre header from mtu info. The expected mtu of gre device
should also subtract gre header. Otherwise, the next packets still
can't be sent out.
Jianlin found this issue when using the topo:
client(ip6gre)<---->(nic1)route(nic2)<----->(ip6gre)server
and reducing nic2's mtu, then both tcp and sctp's performance with
big size data became 0.
This patch is to fix it by also subtracting grehdr (tun->tun_hlen)
from mtu info when updating gre device's mtu in ip6gre_err(). It
also needs to subtract ETH_HLEN if gre dev'type is ARPHRD_ETHER.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
This patch removes CONFIG_NETFILTER_DEBUG and _ASSERT() macros as they
are no longer required. Replace _ASSERT() macros with WARN_ON().
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. Basically, updates to the conntrack core, enhancements for
nf_tables, conversion of netfilter hooks from linked list to array to
improve memory locality and asorted improvements for the Netfilter
codebase. More specifically, they are:
1) Add expection to hashes after timer initialization to prevent
access from another CPU that walks on the hashes and calls
del_timer(), from Florian Westphal.
2) Don't update nf_tables chain counters from hot path, this is only
used by the x_tables compatibility layer.
3) Get rid of nested rcu_read_lock() calls from netfilter hook path.
Hooks are always guaranteed to run from rcu read side, so remove
nested rcu_read_lock() where possible. Patch from Taehee Yoo.
4) nf_tables new ruleset generation notifications include PID and name
of the process that has updated the ruleset, from Phil Sutter.
5) Use skb_header_pointer() from nft_fib, so we can reuse this code from
the nf_family netdev family. Patch from Pablo M. Bermudo.
6) Add support for nft_fib in nf_tables netdev family, also from Pablo.
7) Use deferrable workqueue for conntrack garbage collection, to reduce
power consumption, from Patch from Subash Abhinov Kasiviswanathan.
8) Add nf_ct_expect_iterate_net() helper and use it. From Florian
Westphal.
9) Call nf_ct_unconfirmed_destroy only from cttimeout, from Florian.
10) Drop references on conntrack removal path when skbuffs has escaped via
nfqueue, from Florian.
11) Don't queue packets to nfqueue with dying conntrack, from Florian.
12) Constify nf_hook_ops structure, from Florian.
13) Remove neededlessly branch in nf_tables trace code, from Phil Sutter.
14) Add nla_strdup(), from Phil Sutter.
15) Rise nf_tables objects name size up to 255 chars, people want to use
DNS names, so increase this according to what RFC 1035 specifies.
Patch series from Phil Sutter.
16) Kill nf_conntrack_default_on, it's broken. Default on conntrack hook
registration on demand, suggested by Eric Dumazet, patch from Florian.
17) Remove unused variables in compat_copy_entry_from_user both in
ip_tables and arp_tables code. Patch from Taehee Yoo.
18) Constify struct nf_conntrack_l4proto, from Julia Lawall.
19) Constify nf_loginfo structure, also from Julia.
20) Use a single rb root in connlimit, from Taehee Yoo.
21) Remove unused netfilter_queue_init() prototype, from Taehee Yoo.
22) Use audit_log() instead of open-coding it, from Geliang Tang.
23) Allow to mangle tcp options via nft_exthdr, from Florian.
24) Allow to fetch TCP MSS from nft_rt, from Florian. This includes
a fix for a miscalculation of the minimal length.
25) Simplify branch logic in h323 helper, from Nick Desaulniers.
26) Calculate netlink attribute size for conntrack tuple at compile
time, from Florian.
27) Remove protocol name field from nf_conntrack_{l3,l4}proto structure.
From Florian.
28) Remove holes in nf_conntrack_l4proto structure, so it becomes
smaller. From Florian.
29) Get rid of print_tuple() indirection for /proc conntrack listing.
Place all the code in net/netfilter/nf_conntrack_standalone.c.
Patch from Florian.
30) Do not built in print_conntrack() if CONFIG_NF_CONNTRACK_PROCFS is
off. From Florian.
31) Constify most nf_conntrack_{l3,l4}proto helper functions, from
Florian.
32) Fix broken indentation in ebtables extensions, from Colin Ian King.
33) Fix several harmless sparse warning, from Florian.
34) Convert netfilter hook infrastructure to use array for better memory
locality, joint work done by Florian and Aaron Conole. Moreover, add
some instrumentation to debug this.
35) Batch nf_unregister_net_hooks() calls, to call synchronize_net once
per batch, from Florian.
36) Get rid of noisy logging in ICMPv6 conntrack helper, from Florian.
37) Get rid of obsolete NFDEBUG() instrumentation, from Varsha Rao.
38) Remove unused code in the generic protocol tracker, from Davide
Caratti.
I think I will have material for a second Netfilter batch in my queue if
time allow to make it fit in this merge window.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 1d6119baf0.
After reverting commit 6d7b857d54 ("net: use lib/percpu_counter API
for fragmentation mem accounting") then here is no need for this
fix-up patch. As percpu_counter is no longer used, it cannot
memory leak it any-longer.
Fixes: 6d7b857d54 ("net: use lib/percpu_counter API for fragmentation mem accounting")
Fixes: 1d6119baf0 ("net: fix percpu memory leaks")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a listener registers to the FIB notification chain it receives a
dump of the FIB entries and rules from existing address families by
invoking their dump operations.
While we call into these modules we need to make sure they aren't
removed. Do that by increasing their reference count before invoking
their dump operations and decrease it afterwards.
Fixes: 04b1d4e50e ("net: core: Make the FIB notification chain generic")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grepping for "sizeof\(.+\) / sizeof\(" found this as one of the first
candidates.
Maybe a coccinelle can catch all of those.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In conjunction with crypto offload [1], removing the ESP trailer by
hardware can potentially improve the performance by avoiding (1) a
cache miss incurred by reading the nexthdr field and (2) the necessity
to calculate the csum value of the trailer in order to keep skb->csum
valid.
This patch introduces the changes to the xfrm stack and merely serves
as an infrastructure. Subsequent patch to mlx5 driver will put this to
a good use.
[1] https://www.mail-archive.com/netdev@vger.kernel.org/msg175733.html
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
IPv6 packet may carry more than one extension header, and IPv6 nodes must
accept and attempt to process extension headers in any order and occurring
any number of times in the same packet. Hence, there should be no
assumption that Segment Routing extension header is to appear immediately
after the IPv6 header.
Moreover, section 4.1 of RFC 8200 gives a recommendation on the order of
appearance of those extension headers within an IPv6 packet. According to
this recommendation, Segment Routing extension header should appear after
Hop-by-Hop and Destination Options headers (if they present).
This patch fixes the get_srh(), so it gets the segment routing header
regardless of its position in the chain of the extension headers in IPv6
packet, and makes sure that the IPv6 routing extension header is of Type 4.
Signed-off-by: Ahmed Abdelsalam <amsalam20@gmail.com>
Acked-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian reported UDP xmit drops that could be root caused to the
too small neigh limit.
Current limit is 64 KB, meaning that even a single UDP socket would hit
it, since its default sk_sndbuf comes from net.core.wmem_default
(~212992 bytes on 64bit arches).
Once ARP/ND resolution is in progress, we should allow a little more
packets to be queued, at least for one producer.
Once neigh arp_queue is filled, a rogue socket should hit its sk_sndbuf
limit and either block in sendmsg() or return -EAGAIN.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ChunYu found a kernel warn_on during syzkaller fuzzing:
[40226.038539] WARNING: CPU: 5 PID: 23720 at net/ipv4/af_inet.c:152 inet_sock_destruct+0x78d/0x9a0
[40226.144849] Call Trace:
[40226.147590] <IRQ>
[40226.149859] dump_stack+0xe2/0x186
[40226.176546] __warn+0x1a4/0x1e0
[40226.180066] warn_slowpath_null+0x31/0x40
[40226.184555] inet_sock_destruct+0x78d/0x9a0
[40226.246355] __sk_destruct+0xfa/0x8c0
[40226.290612] rcu_process_callbacks+0xaa0/0x18a0
[40226.336816] __do_softirq+0x241/0x75e
[40226.367758] irq_exit+0x1f6/0x220
[40226.371458] smp_apic_timer_interrupt+0x7b/0xa0
[40226.376507] apic_timer_interrupt+0x93/0xa0
The warn_on happned when sk->sk_rmem_alloc wasn't 0 in inet_sock_destruct.
As after commit f970bd9e3a ("udp: implement memory accounting helpers"),
udp has changed to use udp_destruct_sock as sk_destruct where it would
udp_rmem_release all rmem.
But IPV6_ADDRFORM sockopt sets sk_destruct with inet_sock_destruct after
changing family to PF_INET. If rmem is not 0 at that time, and there is
no place to release rmem before calling inet_sock_destruct, the warn_on
will be triggered.
This patch is to fix it by not setting sk_destruct in IPV6_ADDRFORM sockopt
any more. As IPV6_ADDRFORM sockopt only works for tcp and udp. TCP sock has
already set it's sk_destruct with inet_sock_destruct and UDP has set with
udp_destruct_sock since they're created.
Fixes: f970bd9e3a ("udp: implement memory accounting helpers")
Reported-by: ChunYu Wang <chunwang@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There appears to be no need to use rtnl, addrlabel entries are refcounted
and add/delete is serialized by the addrlabel table spinlock.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2017-08-29
1) Fix dst_entry refcount imbalance when using socket policies.
From Lorenzo Colitti.
2) Fix locking when adding the ESP trailers.
3) Fix tailroom calculation for the ESP trailer by using
skb_tailroom instead of skb_availroom.
4) Fix some info leaks in xfrm_user.
From Mathias Krause.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Now it doesn't check for the cached route expiration in ipv6's
dst_ops->check(), because it trusts dst_gc that would clean the
cached route up when it's expired.
The problem is in dst_gc, it would clean the cached route only
when it's refcount is 1. If some other module (like xfrm) keeps
holding it and the module only release it when dst_ops->check()
fails.
But without checking for the cached route expiration, .check()
may always return true. Meanwhile, without releasing the cached
route, dst_gc couldn't del it. It will cause this cached route
never to expire.
This patch is to set dst.obsolete with DST_OBSOLETE_KILL in .gc
when it's expired, and check obsolete != DST_OBSOLETE_FORCE_CHK
in .check.
Note that this is even needed when ipv6 dst_gc timer is removed
one day. It would set dst.obsolete in .redirect and .update_pmtu
instead, and check for cached route expiration when getting it,
just like what ipv4 route does.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c5cff8561d adds rcu grace period before freeing fib6_node. This
generates a new sparse warning on rt->rt6i_node related code:
net/ipv6/route.c:1394:30: error: incompatible types in comparison
expression (different address spaces)
./include/net/ip6_fib.h:187:14: error: incompatible types in comparison
expression (different address spaces)
This commit adds "__rcu" tag for rt6i_node and makes sure corresponding
rcu API is used for it.
After this fix, sparse no longer generates the above warning.
Fixes: c5cff8561d ("ipv6: add rcu grace period before freeing fib6_node")
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Twice patches trying to constify inet{6}_protocol have been reverted:
39294c3df2 ("Revert "ipv6: constify inet6_protocol structures"") to
revert 3a3a4e3054 and then 03157937fe ("Revert "ipv4: make
net_protocol const"") to revert aa8db499ea.
Add a comment that the structures can not be const because the
early_demux field can change based on a sysctl.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling logging for invalid connections we currently also log most
icmpv6 types, which we don't track intentionally (e.g. neigh discovery).
"invalid" should really mean "invalid", i.e. short header or bad checksum.
We don't do any logging for icmp(v4) either, its just useless noise.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently, in the udp6 code, the dst cookie is not initialized/updated
concurrently with the RX dst used by early demux.
As a result, the dst_check() in the early_demux path always fails,
the rx dst cache is always invalidated, and we can't really
leverage significant gain from the demux lookup.
Fix it adding udp6 specific variant of sk_rx_dst_set() and use it
to set the dst cookie when the dst entry is really changed.
The issue is there since the introduction of early demux for ipv6.
Fixes: 5425077d73 ("net: ipv6: Add early demux handler for UDP unicast")
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the following seg6local actions.
- SEG6_LOCAL_ACTION_END_T: regular SRH processing and forward to the
next-hop looked up in the specified routing table.
- SEG6_LOCAL_ACTION_END_DX2: decapsulate an L2 frame and forward it to
the specified network interface.
- SEG6_LOCAL_ACTION_END_DX4: decapsulate an IPv4 packet and forward it,
possibly to the specified next-hop.
- SEG6_LOCAL_ACTION_END_DT6: decapsulate an IPv6 packet and forward it
to the next-hop looked up in the specified routing table.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds three helper functions to be used with the seg6local packet
processing actions.
The decap_and_validate() function will be used by the End.D* actions, that
decapsulate an SR-enabled packet.
The advance_nextseg() function applies the fundamental operations to update
an SRH for the next segment.
The lookup_nexthop() function helps select the next-hop for the processed
SR packets. It supports an optional next-hop address to route the packet
specifically through it, and an optional routing table to use.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch ensures that the seg6local lightweight tunnel is used solely
with IPv6 routes and processes only IPv6 packets.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the L2 frame encapsulation mechanism, referred to
as T.Encaps.L2 in the SRv6 specifications [1].
A new type of SRv6 tunnel mode is added (SEG6_IPTUN_MODE_L2ENCAP). It only
accepts packets with an existing MAC header (i.e., it will not work for
locally generated packets). The resulting packet looks like IPv6 -> SRH ->
Ethernet -> original L3 payload. The next header field of the SRH is set to
NEXTHDR_NONE.
[1] https://tools.ietf.org/html/draft-filsfils-spring-srv6-network-programming-01
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables the SRv6 encapsulation mode to carry an IPv4 payload.
All the infrastructure was already present, I just had to add a parameter
to seg6_do_srh_encap() to specify the inner packet protocol, and perform
some additional checks.
Usage example:
ip route add 1.2.3.4 encap seg6 mode encap segs fc00::1,fc00::2 dev eth0
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
rt_cookie might be used uninitialized, fix this by
initializing it.
Fixes: c5cff8561d ("ipv6: add rcu grace period before freeing fib6_node")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We use skb_availroom to calculate the skb tailroom for the
ESP trailer. skb_availroom calculates the tailroom and
subtracts this value by reserved_tailroom. However
reserved_tailroom is a union with the skb mark. This means
that we subtract the tailroom by the skb mark if set.
Fix this by using skb_tailroom instead.
Fixes: cac2661c53 ("esp4: Avoid skb_cow_data whenever possible")
Fixes: 03e2a30f6a ("esp6: Avoid skb_cow_data whenever possible")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
We allocate the page fragment for the ESP trailer inside
a spinlock, but consume it outside of the lock. This
is racy as some other cou could get the same page fragment
then. Fix this by consuming the page fragment inside the
lock too.
Fixes: cac2661c53 ("esp4: Avoid skb_cow_data whenever possible")
Fixes: 03e2a30f6a ("esp6: Avoid skb_cow_data whenever possible")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Allow our callers to influence the choice of ECMP link by honoring the
hash passed together with the flow info. This allows for special
treatment of ICMP errors which we would like to route over the same path
as the IPv6 datagram that triggered the error.
Also go through rt6_multipath_hash(), in the usual case when we aren't
dealing with an ICMP error, so that there is one central place where
multipath hash is computed.
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 644d0e6569 ("ipv6 Use get_hash_from_flowi6 for rt6 hash") has
turned rt6_info_hash_nhsfn() into a one-liner, so it no longer makes
sense to keep it around. Also remove the accompanying comment that has
become outdated.
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When forwarding or sending out an ICMPv6 error, look at the embedded
packet that triggered the error and compute a flow hash over its
headers.
This let's us route the ICMP error together with the flow it belongs to
when multipath (ECMP) routing is in use, which in turn makes Path MTU
Discovery work in ECMP load-balanced or anycast setups (RFC 7690).
Granted, end-hosts behind the ECMP router (aka servers) need to reflect
the IPv6 Flow Label for PMTUD to work.
The code is organized to be in parallel with ipv4 stack:
ip_multipath_l3_keys -> ip6_multipath_l3_keys
fib_multipath_hash -> rt6_multipath_hash
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reflecting IPv6 Flow Label at server nodes is useful in environments
that employ multipath routing to load balance the requests. As "IPv6
Flow Label Reflection" standard draft [1] points out - ICMPv6 PTB error
messages generated in response to a downstream packets from the server
can be routed by a load balancer back to the original server without
looking at transport headers, if the server applies the flow label
reflection. This enables the Path MTU Discovery past the ECMP router in
load-balance or anycast environments where each server node is reachable
by only one path.
Introduce a sysctl to enable flow label reflection per net namespace for
all newly created sockets. Same could be earlier achieved only per
socket by setting the IPV6_FL_F_REFLECT flag for the IPV6_FLOWLABEL_MGR
socket option.
[1] https://tools.ietf.org/html/draft-wang-6man-flow-label-reflection-01
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_NF_CONNTRACK_PROCFS is deprecated, no need to use a function
pointer in the trackers for this. Place the printf formatting in
the one place that uses it.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
no need to waste storage for something that is only needed
in one place and can be deduced from protocol number.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
no need to waste storage for something that is only needed
in one place and can be deduced from protocol number.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
avoids a pointer and allows struct to be const later on.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When SOF_TIMESTAMPING_RX_SOFTWARE is enabled for tcp sockets, return the
timestamp corresponding to the highest sequence number data returned.
Previously the skb->tstamp is overwritten when a TCP packet is placed
in the out of order queue. While the packet is in the ooo queue, save the
timestamp in the TCB_SKB_CB. This space is shared with the gso_*
options which are only used on the tx path, and a previously unused 4
byte hole.
When skbs are coalesced either in the sk_receive_queue or the
out_of_order_queue always choose the timestamp of the appended skb to
maintain the invariant of returning the timestamp of the last byte in
the recvmsg buffer.
Signed-off-by: Mike Maloney <maloney@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently keep rt->rt6i_node pointing to the fib6_node for the route.
And some functions make use of this pointer to dereference the fib6_node
from rt structure, e.g. rt6_check(). However, as there is neither
refcount nor rcu taken when dereferencing rt->rt6i_node, it could
potentially cause crashes as rt->rt6i_node could be set to NULL by other
CPUs when doing a route deletion.
This patch introduces an rcu grace period before freeing fib6_node and
makes sure the functions that dereference it takes rcu_read_lock().
Note: there is no "Fixes" tag because this bug was there in a very
early stage.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2017-08-21
1) Fix memleaks when ESP takes an error path.
2) Fix null pointer dereference when creating a sub policy
that matches the same outer flow as main policy does.
From Koichiro Den.
3) Fix possible out-of-bound access in xfrm_migrate.
This patch should go to the stable trees too.
From Vladis Dronov.
4) ESP can return positive and negative error values,
so treat both cases as an error.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A packet length of exactly IPV6_MAXPLEN is allowed, we should
refuse parsing options only if the size is 64KiB or more.
While at it, remove one extra variable and one assignment which
were also introduced by the commit that introduced the size
check. Checking the sum 'offset + len' and only later adding
'len' to 'offset' doesn't provide any advantage over directly
summing to 'offset' and checking it.
Fixes: 6399f1fae4 ("ipv6: avoid overflow of offset in ip6_find_1stfragopt")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One nagging difference between ipv4 and ipv6 is host routes for ipv6
addresses are installed using the loopback device or VRF / L3 Master
device. e.g.,
2001:db8:1::/120 dev veth0 proto kernel metric 256 pref medium
local 2001:db8:1::1 dev lo table local proto kernel metric 0 pref medium
Using the loopback device is convenient -- necessary for local tx, but
has some nasty side effects, most notably setting the 'lo' device down
causes all host routes for all local IPv6 address to be removed from the
FIB and completely breaks IPv6 networking across all interfaces.
This patch puts FIB entries for IPv6 routes against the device. This
simplifies the routes in the FIB, for example by making dst->dev and
rt6i_idev->dev the same (a future patch can look at removing the device
reference taken for rt6i_idev for FIB entries).
When copies are made on FIB lookups, the cloned route has dst->dev
set to loopback (or the L3 master device). This is needed for the
local Tx of packets to local addresses.
With fib entries allocated against the real network device, the addrconf
code that reinserts host routes on admin up of 'lo' is no longer needed.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-08-21
1) Support RX checksum with IPsec crypto offload for esp4/esp6.
From Ilan Tayari.
2) Fixup IPv6 checksums when doing IPsec crypto offload.
From Yossi Kuperman.
3) Auto load the xfrom offload modules if a user installs
a SA that requests IPsec offload. From Ilan Tayari.
4) Clear RX offload informations in xfrm_input to not
confuse the TX path with stale offload informations.
From Ilan Tayari.
5) Allow IPsec GSO for local sockets if the crypto operation
will be offloaded.
6) Support setting of an output mark to the xfrm_state.
This mark can be used to to do the tunnel route lookup.
From Lorenzo Colitti.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In fib6_add(), it is possible that fib6_add_1() picks an intermediate
node and sets the node's fn->leaf to NULL in order to add this new
route. However, if fib6_add_rt2node() fails to add the new
route for some reason, fn->leaf will be left as NULL and could
potentially cause crash when fn->leaf is accessed in fib6_locate().
This patch makes sure fib6_repair_tree() is called to properly repair
fn->leaf in the above failure case.
Here is the syzkaller reported general protection fault in fib6_locate:
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] SMP KASAN
Modules linked in:
CPU: 0 PID: 40937 Comm: syz-executor3 Not tainted
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
task: ffff8801d7d64100 ti: ffff8801d01a0000 task.ti: ffff8801d01a0000
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] __ipv6_prefix_equal64_half include/net/ipv6.h:475 [inline]
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] ipv6_prefix_equal include/net/ipv6.h:492 [inline]
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] fib6_locate_1 net/ipv6/ip6_fib.c:1210 [inline]
RIP: 0010:[<ffffffff82a3e0e1>] [<ffffffff82a3e0e1>] fib6_locate+0x281/0x3c0 net/ipv6/ip6_fib.c:1233
RSP: 0018:ffff8801d01a36a8 EFLAGS: 00010202
RAX: 0000000000000020 RBX: ffff8801bc790e00 RCX: ffffc90002983000
RDX: 0000000000001219 RSI: ffff8801d01a37a0 RDI: 0000000000000100
RBP: ffff8801d01a36f0 R08: 00000000000000ff R09: 0000000000000000
R10: 0000000000000003 R11: 0000000000000000 R12: 0000000000000001
R13: dffffc0000000000 R14: ffff8801d01a37a0 R15: 0000000000000000
FS: 00007f6afd68c700(0000) GS:ffff8801db400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000004c6340 CR3: 00000000ba41f000 CR4: 00000000001426f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Stack:
ffff8801d01a37a8 ffff8801d01a3780 ffffed003a0346f5 0000000c82a23ea0
ffff8800b7bd7700 ffff8801d01a3780 ffff8800b6a1c940 ffffffff82a23ea0
ffff8801d01a3920 ffff8801d01a3748 ffffffff82a223d6 ffff8801d7d64988
Call Trace:
[<ffffffff82a223d6>] ip6_route_del+0x106/0x570 net/ipv6/route.c:2109
[<ffffffff82a23f9d>] inet6_rtm_delroute+0xfd/0x100 net/ipv6/route.c:3075
[<ffffffff82621359>] rtnetlink_rcv_msg+0x549/0x7a0 net/core/rtnetlink.c:3450
[<ffffffff8274c1d1>] netlink_rcv_skb+0x141/0x370 net/netlink/af_netlink.c:2281
[<ffffffff82613ddf>] rtnetlink_rcv+0x2f/0x40 net/core/rtnetlink.c:3456
[<ffffffff8274ad38>] netlink_unicast_kernel net/netlink/af_netlink.c:1206 [inline]
[<ffffffff8274ad38>] netlink_unicast+0x518/0x750 net/netlink/af_netlink.c:1232
[<ffffffff8274b83e>] netlink_sendmsg+0x8ce/0xc30 net/netlink/af_netlink.c:1778
[<ffffffff82564aff>] sock_sendmsg_nosec net/socket.c:609 [inline]
[<ffffffff82564aff>] sock_sendmsg+0xcf/0x110 net/socket.c:619
[<ffffffff82564d62>] sock_write_iter+0x222/0x3a0 net/socket.c:834
[<ffffffff8178523d>] new_sync_write+0x1dd/0x2b0 fs/read_write.c:478
[<ffffffff817853f4>] __vfs_write+0xe4/0x110 fs/read_write.c:491
[<ffffffff81786c38>] vfs_write+0x178/0x4b0 fs/read_write.c:538
[<ffffffff817892a9>] SYSC_write fs/read_write.c:585 [inline]
[<ffffffff817892a9>] SyS_write+0xd9/0x1b0 fs/read_write.c:577
[<ffffffff82c71e32>] entry_SYSCALL_64_fastpath+0x12/0x17
Note: there is no "Fixes" tag as this seems to be a bug introduced
very early.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzcaller reported the following use-after-free issue in rt6_select():
BUG: KASAN: use-after-free in rt6_select net/ipv6/route.c:755 [inline] at addr ffff8800bc6994e8
BUG: KASAN: use-after-free in ip6_pol_route.isra.46+0x1429/0x1470 net/ipv6/route.c:1084 at addr ffff8800bc6994e8
Read of size 4 by task syz-executor1/439628
CPU: 0 PID: 439628 Comm: syz-executor1 Not tainted 4.3.5+ #8
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
0000000000000000 ffff88018fe435b0 ffffffff81ca384d ffff8801d3588c00
ffff8800bc699380 ffff8800bc699500 dffffc0000000000 ffff8801d40a47c0
ffff88018fe435d8 ffffffff81735751 ffff88018fe43660 ffff8800bc699380
Call Trace:
[<ffffffff81ca384d>] __dump_stack lib/dump_stack.c:15 [inline]
[<ffffffff81ca384d>] dump_stack+0xc1/0x124 lib/dump_stack.c:51
sctp: [Deprecated]: syz-executor0 (pid 439615) Use of struct sctp_assoc_value in delayed_ack socket option.
Use struct sctp_sack_info instead
[<ffffffff81735751>] kasan_object_err+0x21/0x70 mm/kasan/report.c:158
[<ffffffff817359c4>] print_address_description mm/kasan/report.c:196 [inline]
[<ffffffff817359c4>] kasan_report_error+0x1b4/0x4a0 mm/kasan/report.c:285
[<ffffffff81735d93>] kasan_report mm/kasan/report.c:305 [inline]
[<ffffffff81735d93>] __asan_report_load4_noabort+0x43/0x50 mm/kasan/report.c:325
[<ffffffff82a28e39>] rt6_select net/ipv6/route.c:755 [inline]
[<ffffffff82a28e39>] ip6_pol_route.isra.46+0x1429/0x1470 net/ipv6/route.c:1084
[<ffffffff82a28fb1>] ip6_pol_route_output+0x81/0xb0 net/ipv6/route.c:1203
[<ffffffff82ab0a50>] fib6_rule_action+0x1f0/0x680 net/ipv6/fib6_rules.c:95
[<ffffffff8265cbb6>] fib_rules_lookup+0x2a6/0x7a0 net/core/fib_rules.c:223
[<ffffffff82ab1430>] fib6_rule_lookup+0xd0/0x250 net/ipv6/fib6_rules.c:41
[<ffffffff82a22006>] ip6_route_output+0x1d6/0x2c0 net/ipv6/route.c:1224
[<ffffffff829e83d2>] ip6_dst_lookup_tail+0x4d2/0x890 net/ipv6/ip6_output.c:943
[<ffffffff829e889a>] ip6_dst_lookup_flow+0x9a/0x250 net/ipv6/ip6_output.c:1079
[<ffffffff82a9f7d8>] ip6_datagram_dst_update+0x538/0xd40 net/ipv6/datagram.c:91
[<ffffffff82aa0978>] __ip6_datagram_connect net/ipv6/datagram.c:251 [inline]
[<ffffffff82aa0978>] ip6_datagram_connect+0x518/0xe50 net/ipv6/datagram.c:272
[<ffffffff82aa1313>] ip6_datagram_connect_v6_only+0x63/0x90 net/ipv6/datagram.c:284
[<ffffffff8292f790>] inet_dgram_connect+0x170/0x1f0 net/ipv4/af_inet.c:564
[<ffffffff82565547>] SYSC_connect+0x1a7/0x2f0 net/socket.c:1582
[<ffffffff8256a649>] SyS_connect+0x29/0x30 net/socket.c:1563
[<ffffffff82c72032>] entry_SYSCALL_64_fastpath+0x12/0x17
Object at ffff8800bc699380, in cache ip6_dst_cache size: 384
The root cause of it is that in fib6_add_rt2node(), when it replaces an
existing route with the new one, it does not update fn->rr_ptr.
This commit resets fn->rr_ptr to NULL when it points to a route which is
replaced in fib6_add_rt2node().
Fixes: 2759647247 ("ipv6: fix ECMP route replacement")
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to commit e6afc8ace6 ("udp: remove
headers from UDP packets before queueing"), when udp packets are being
peeked the requested extra offset is always 0 as there is no need to skip
the udp header. However, when the offset is 0 and the next skb is
of length 0, it is only returned once. The behaviour can be seen with
the following python script:
from socket import *;
f=socket(AF_INET6, SOCK_DGRAM | SOCK_NONBLOCK, 0);
g=socket(AF_INET6, SOCK_DGRAM | SOCK_NONBLOCK, 0);
f.bind(('::', 0));
addr=('::1', f.getsockname()[1]);
g.sendto(b'', addr)
g.sendto(b'b', addr)
print(f.recvfrom(10, MSG_PEEK));
print(f.recvfrom(10, MSG_PEEK));
Where the expected output should be the empty string twice.
Instead, make sk_peek_offset return negative values, and pass those values
to __skb_try_recv_datagram/__skb_try_recv_from_queue. If the passed offset
to __skb_try_recv_from_queue is negative, the checked skb is never skipped.
__skb_try_recv_from_queue will then ensure the offset is reset back to 0
if a peek is requested without an offset, unless no packets are found.
Also simplify the if condition in __skb_try_recv_from_queue. If _off is
greater then 0, and off is greater then or equal to skb->len, then
(_off || skb->len) must always be true assuming skb->len >= 0 is always
true.
Also remove a redundant check around a call to sk_peek_offset in af_unix.c,
as it double checked if MSG_PEEK was set in the flags.
V2:
- Moved the negative fixup into __skb_try_recv_from_queue, and remove now
redundant checks
- Fix peeking in udp{,v6}_recvmsg to report the right value when the
offset is 0
V3:
- Marked new branch in __skb_try_recv_from_queue as unlikely.
Signed-off-by: Matthew Dawson <matthew@mjdsystems.ca>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding a lock around one of the assignments prevents gcc from
tracking the state of the local 'fibmatch' variable, so it can no
longer prove that 'dst' is always initialized, leading to a bogus
warning:
net/ipv6/route.c: In function 'inet6_rtm_getroute':
net/ipv6/route.c:3659:2: error: 'dst' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This moves the other assignment into the same lock to shut up the
warning.
Fixes: 121622dba8 ("ipv6: route: make rtm_getroute not assume rtnl is locked")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
To complete the sendmsg_locked and sendpage_locked implementation add
the hooks for af_inet6 as well.
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__dev_get_by_index assumes RTNL is held, use _rcu version instead.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv6 routes currently lack nexthop flags as in IPv4. This has several
implications.
In the forwarding path, it requires us to check the carrier state of the
nexthop device and potentially ignore a linkdown route, instead of
checking for RTNH_F_LINKDOWN.
It also requires capable drivers to use the user facing IPv6-specific
route flags to provide offload indication, instead of using the nexthop
flags as in IPv4.
Add nexthop flags to IPv6 routes in the 40 bytes hole and use it to
provide offload indication instead of the RTF_OFFLOAD flag, which is
removed while it's still not part of any official kernel release.
In the near future we would like to use the field for the
RTNH_F_{LINKDOWN,DEAD} flags, but this change is more involved and might
not be ready in time for the current cycle.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filtering the ACK packet was not put at the right place.
At this place, we already allocated a child and put it
into accept queue.
We absolutely need to call tcp_child_process() to release
its spinlock, or we will deadlock at accept() or close() time.
Found by syzkaller team (Thanks a lot !)
Fixes: 8fac365f63 ("tcp: Add a tcp_filter hook before handle ack packet")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Chenbo Feng <fengc@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a dst is created by addrconf_dst_alloc() for a host route or an
anycast route, dst->dev points to loopback dev while rt6->rt6i_idev
points to a real device.
When the real device goes down, the current cleanup code only checks for
dst->dev and assumes rt6->rt6i_idev->dev is the same. This causes the
refcount leak on the real device in the above situation.
This patch makes sure to always release the refcount taken on
rt6->rt6i_idev during dst_dev_put().
Fixes: 587fea7411 ("ipv6: mark DST_NOGC and remove the operation of
dst_free()")
Reported-by: John Stultz <john.stultz@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
include/linux/mm_types.h
mm/huge_memory.c
I removed the smp_mb__before_spinlock() like the following commit does:
8b1b436dd1 ("mm, locking: Rework {set,clear,mm}_tlb_flush_pending()")
and fixed up the affected commits.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On systems that use mark-based routing it may be necessary for
routing lookups to use marks in order for packets to be routed
correctly. An example of such a system is Android, which uses
socket marks to route packets via different networks.
Currently, routing lookups in tunnel mode always use a mark of
zero, making routing incorrect on such systems.
This patch adds a new output_mark element to the xfrm state and
a corresponding XFRMA_OUTPUT_MARK netlink attribute. The output
mark differs from the existing xfrm mark in two ways:
1. The xfrm mark is used to match xfrm policies and states, while
the xfrm output mark is used to set the mark (and influence
the routing) of the packets emitted by those states.
2. The existing mark is constrained to be a subset of the bits of
the originating socket or transformed packet, but the output
mark is arbitrary and depends only on the state.
The use of a separate mark provides additional flexibility. For
example:
- A packet subject to two transforms (e.g., transport mode inside
tunnel mode) can have two different output marks applied to it,
one for the transport mode SA and one for the tunnel mode SA.
- On a system where socket marks determine routing, the packets
emitted by an IPsec tunnel can be routed based on a mark that
is determined by the tunnel, not by the marks of the
unencrypted packets.
- Support for setting the output marks can be introduced without
breaking any existing setups that employ both mark-based
routing and xfrm tunnel mode. Simply changing the code to use
the xfrm mark for routing output packets could xfrm mark could
change behaviour in a way that breaks these setups.
If the output mark is unspecified or set to zero, the mark is not
set or changed.
Tested: make allyesconfig; make -j64
Tested: https://android-review.googlesource.com/452776
Signed-off-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
When iteratively building a UDP datagram with MSG_MORE and that
datagram exceeds MTU, consistently choose UFO or fragmentation.
Once skb_is_gso, always apply ufo. Conversely, once a datagram is
split across multiple skbs, do not consider ufo.
Sendpage already maintains the first invariant, only add the second.
IPv6 does not have a sendpage implementation to modify.
A gso skb must have a partial checksum, do not follow sk_no_check_tx
in udp_send_skb.
Found by syzkaller.
Fixes: e89e9cf539 ("[IPv4/IPv6]: UFO Scatter-gather approach")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any use of key->enabled (that is static_key_enabled and static_key_count)
outside jump_label_lock should handle its own serialization. The only
two that are not doing so are the UDP encapsulation static keys. Change
them to use static_key_enable, which now correctly tests key->enabled under
the jump label lock.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jason Baron <jbaron@akamai.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1501601046-35683-3-git-send-email-pbonzini@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
ndisc_notify is used to send unsolicited neighbor advertisements
(e.g., on a link up). Currently, the ndisc notifier is run before the
addrconf notifer which means NA's are not sent for link-local addresses
which are added by the addrconf notifier.
Fix by lowering the priority of the ndisc notifier. Setting the priority
to ADDRCONF_NOTIFY_PRIORITY - 5 means it runs after addrconf and before
the route notifier which is ADDRCONF_NOTIFY_PRIORITY - 10.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change allows us to later indicate to rtnetlink core that certain
doit functions should be called without acquiring rtnl_mutex.
This change should have no effect, we simply replace the last (now
unused) calcit argument with the new flag.
Signed-off-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP offload conflict is dealt with by simply taking what is
in net-next where we have removed all of the UFO handling code
entirely.
The TCP conflict was a case of local variables in a function
being removed from both net and net-next.
In netvsc we had an assignment right next to where a missing
set of u64 stats sync object inits were added.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the user hasn't installed any custom rules, don't go through the
whole FIB rules layer. This is pretty similar to f4530fa574 (ipv4:
Avoid overhead when no custom FIB rules are installed).
Using a micro-benchmark module [1], timing ip6_route_output() with
get_cycles(), with 40,000 routes in the main routing table, before this
patch:
min=606 max=12911 count=627 average=1959 95th=4903 90th=3747 50th=1602 mad=821
table=254 avgdepth=21.8 maxdepth=39
value │ ┊ count
600 │▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒ 199
880 │▒▒▒░░░░░░░░░░░░░░░░ 43
1160 │▒▒▒░░░░░░░░░░░░░░░░░░░░ 48
1440 │▒▒▒░░░░░░░░░░░░░░░░░░░░░░░ 43
1720 │▒▒▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░ 59
2000 │▒▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 50
2280 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 26
2560 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 31
2840 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 28
3120 │▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 17
3400 │▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 17
3680 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 8
3960 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 11
4240 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 6
4520 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 6
4800 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 9
After:
min=544 max=11687 count=627 average=1776 95th=4546 90th=3585 50th=1227 mad=565
table=254 avgdepth=21.8 maxdepth=39
value │ ┊ count
540 │▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒ 201
800 │▒▒▒▒▒░░░░░░░░░░░░░░░░ 63
1060 │▒▒▒▒▒░░░░░░░░░░░░░░░░░░░░░ 68
1320 │▒▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░ 39
1580 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 32
1840 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 32
2100 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 34
2360 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 33
2620 │▒▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 26
2880 │▒░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 22
3140 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 9
3400 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 8
3660 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 9
3920 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 8
4180 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 8
4440 │░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░░ 8
At the frequency of the host during the bench (~ 3.7 GHz), this is
about a 100 ns difference on the median value.
A next step would be to collapse local and main tables, as in
0ddcf43d5d (ipv4: FIB Local/MAIN table collapse).
[1]: https://github.com/vincentbernat/network-lab/blob/master/lab-routes-ipv6/kbench_mod.c
Signed-off-by: Vincent Bernat <vincent@bernat.im>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_warn_bad_offload triggers a warning when an skb enters the GSO
stack at __skb_gso_segment that does not have CHECKSUM_PARTIAL
checksum offload set.
Commit b2504a5dbe ("net: reduce skb_warn_bad_offload() noise")
observed that SKB_GSO_DODGY producers can trigger the check and
that passing those packets through the GSO handlers will fix it
up. But, the software UFO handler will set ip_summed to
CHECKSUM_NONE.
When __skb_gso_segment is called from the receive path, this
triggers the warning again.
Make UFO set CHECKSUM_UNNECESSARY instead of CHECKSUM_NONE. On
Tx these two are equivalent. On Rx, this better matches the
skb state (checksum computed), as CHECKSUM_NONE here means no
checksum computed.
See also this thread for context:
http://patchwork.ozlabs.org/patch/799015/
Fixes: b2504a5dbe ("net: reduce skb_warn_bad_offload() noise")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the following seg6local actions.
- SEG6_LOCAL_ACTION_END: regular SRH processing. The DA of the packet
is updated to the next segment and forwarded accordingly.
- SEG6_LOCAL_ACTION_END_X: same as above, except that the packet is
forwarded to the specified IPv6 next-hop.
- SEG6_LOCAL_ACTION_END_DX6: decapsulate the packet and forward to
inner IPv6 packet to the specified IPv6 next-hop.
- SEG6_LOCAL_ACTION_END_B6: insert the specified SRH directly after
the IPv6 header of the packet.
- SEG6_LOCAL_ACTION_END_B6_ENCAP: encapsulate the packet within
an outer IPv6 header, containing the specified SRH.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the necessary functions to parse, fill, and compare
seg6local rtnetlink attributes, for all defined action parameters.
- The SRH parameter defines an SRH to be inserted or encapsulated.
- The TABLE parameter defines the table to use for the route lookup of
the next segment or the inner decapsulated packet.
- The NH4 parameter defines the IPv4 next-hop for an inner decapsulated
IPv4 packet.
- The NH6 parameter defines the IPv6 next-hop for the next segment or
for an inner decapsulated IPv6 packet
- The IIF parameter defines an ingress interface index.
- The OIF parameter defines an egress interface index.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements a new type of lightweight tunnel named seg6local.
A seg6local lwt is defined by a type of action and a set of parameters.
The action represents the operation to perform on the packets matching the
lwt's route, and is not necessarily an encapsulation. The set of parameters
are arguments for the processing function.
Each action is defined in a struct seg6_action_desc within
seg6_action_table[]. This structure contains the action, mandatory
attributes, the processing function, and a static headroom size required by
the action. The mandatory attributes are encoded as a bitmask field. The
static headroom is set to a non-zero value when the processing function
always add a constant number of bytes to the skb (e.g. the header size for
encapsulations).
To facilitate rtnetlink-related operations such as parsing, fill_encap,
and cmp_encap, each type of action parameter is associated to three
function pointers, in seg6_action_params[].
All actions defined in seg6_local.h are detailed in [1].
[1] https://tools.ietf.org/html/draft-filsfils-spring-srv6-network-programming-01
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch exports the seg6_do_srh_encap() and seg6_do_srh_inline()
functions. It also removes the CONFIG_IPV6_SEG6_INLINE knob
that enabled the compilation of seg6_do_srh_inline(). This function
is now built-in.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
The seg6_validate_srh() function only allows SRHs whose active segment is
the first segment of the path. However, an application may insert an SRH
whose active segment is not the first one. Such an application might be
for example an SR-aware Virtual Network Function.
This patch enables to insert SRHs with an arbitrary active segment.
Signed-off-by: David Lebrun <david.lebrun@uclouvain.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a second device index, sdif, to raw socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a second device index, sdif, to inet6 socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
TCP moves the data in the cb. Prior to tcp_v4_rcv (e.g., early demux) the
ingress index is obtained from IPCB using inet_sdif and after tcp_v4_rcv
tcp_v4_sdif is used.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a second device index, sdif, to udp socket lookups. sdif is the
index for ingress devices enslaved to an l3mdev. It allows the lookups
to consider the enslaved device as well as the L3 domain when searching
for a socket.
Early demux lookups are handled in the next patch as part of INET_MATCH
changes.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
esp_output_tail() and esp6_output_tail() can return negative
and positive error values. We currently treat only negative
values as errors, fix this to treat both cases as error.
Fixes: fca11ebde3 ("esp4: Reorganize esp_output")
Fixes: 383d0350f2 ("esp6: Reorganize esp_output")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Similar to commit 1c677b3d28 ("ipv4: fib: Add fib_info_hold() helper")
and commit b423cb1080 ("ipv4: fib: Export free_fib_info()") add an
helper to hold a reference on rt6_info and export rt6_release() to drop
it and potentially release the route.
This is needed so that drivers capable of FIB offload could hold a
reference on the route before queueing it for offload and drop it after
the route has been programmed to the device's tables.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is brought back up, the kernel tries to restore the
host routes tied to its permanent addresses.
However, if the host route was removed from the FIB, then we need to
reinsert it. This is done by releasing the current dst and allocating a
new, so as to not reuse a dst with obsolete values.
Since this function is called under RTNL and using the same explanation
from the previous patch, we can test if the route is in the FIB by
checking its node pointer instead of its reference count.
Tested using the following script and Andrey's reproducer mentioned
in commit 8048ced9be ("net: ipv6: regenerate host route if moved to gc
list") and linked below:
$ ip link set dev lo up
$ ip link add dummy1 type dummy
$ ip -6 address add cafe::1/64 dev dummy1
$ ip link set dev lo down # cafe::1/128 is removed
$ ip link set dev dummy1 up
$ ip link set dev lo up
The host route is correctly regenerated.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Link: http://lkml.kernel.org/r/CAAeHK+zSe82vc5gCRgr_EoUwiALPnWVdWJBPwJZBpbxYz=kGJw@mail.gmail.com
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the loopback device is brought back up we need to check if the host
route attached to the address is still in the FIB and regenerate one in
case it's not.
Host routes using the loopback device are always inserted into and
removed from the FIB under RTNL (under which this function is called),
so we can test their node pointer instead of the reference count in
order to check if the route is in the FIB or not.
Tested using the following script from Nicolas mentioned in
commit a220445f9f ("ipv6: correctly add local routes when lo goes up"):
$ ip link add dummy1 type dummy
$ ip link set dummy1 up
$ ip link set lo down ; ip link set lo up
The host route is correctly regenerated.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a route is deleted its node pointer is set to NULL to indicate it's
no longer linked to its node. Do the same for routes that are replaced.
This will later allow us to test if a route is still in the FIB by
checking its node pointer instead of its reference count.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code currently assumes that only FIB nodes can hold a reference on
routes. Therefore, after fib6_purge_rt() has run and the route is no
longer present in any intermediate nodes, it's assumed that its
reference count would be 1 - taken by the node where it's currently
stored.
However, we're going to allow users other than the FIB to take a
reference on a route, so this assumption is no longer valid and the
BUG_ON() needs to be removed.
Note that purging only takes place if the initial reference count is
different than 1. I've left that check intact, as in the majority of
systems (where routes are only referenced by the FIB), it does actually
mean the route is present in intermediate nodes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow user space applications to see which routes are offloaded and
which aren't by setting the RTNH_F_OFFLOAD flag when dumping them.
To be consistent with IPv4, offload indication is provided on a
per-nexthop basis.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dump all the FIB tables in each net namespace upon registration to the
FIB notification chain so that the callee will have a complete view of
the tables.
The integrity of the dump is ensured by a per-table sequence counter
that is incremented (under write lock) whenever a route is added or
deleted from the table.
All the sequence counters are read (under each table's read lock) and
summed, prior and after the dump. In case the counters differ, then the
dump is either restarted or the registration fails.
While it's possible for a table to be modified after its counter has
been read, this isn't really a problem. In case it happened before it
was read the second time, then the comparison at the end will fail. If
it happened afterwards, then we're guaranteed to be notified about the
change, as the notification block is registered prior to the second
read.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow users of the FIB notification chain to receive a complete view of
the IPv6 FIB rules upon registration to the chain.
The integrity of the dump is ensured by a per-family sequence counter
that is incremented (under RTNL) whenever a rule is added or deleted.
All the sequence counters are read (under RTNL) and summed, prior and
after the dump. In case the counters differ, then the dump is either
restarted or the registration fails.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As with IPv4, allow listeners of the FIB notification chain to receive
notifications whenever a route is added, replaced or deleted. This is
done by placing calls to the FIB notification chain in the two lowest
level functions that end up performing these operations - namely,
fib6_add_rt2node() and fib6_del_route().
Unlike IPv4, APPEND notifications aren't sent as the kernel doesn't
distinguish between "append" (NLM_F_CREATE|NLM_F_APPEND) and "prepend"
(NLM_F_CREATE). If NLM_F_EXCL isn't set, duplicate routes are always
added after the existing duplicate routes.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're about to add IPv6 FIB offload support, so implement the necessary
callbacks in IPv6 code, which will later allow us to add routes and
rules notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As explained in commit 3c71006d15 ("ipv4: fib_rules: Check if rule is
a default rule"), drivers supporting IPv6 FIB offload need to be able to
sanitize the rules they don't support and potentially flush their
tables.
Add an IPv6 helper to check if a FIB rule is a default rule.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit c2ed1880fd ("net: ipv6: check route protocol when
deleting routes"), ipv6 route checks rt protocol when trying to
remove a rt entry.
It introduced a side effect causing 'ip -6 route flush cache' not
to work well. When flushing caches with iproute, all route caches
get dumped from kernel then removed one by one by sending DELROUTE
requests to kernel for each cache.
The thing is iproute sends the request with the cache whose proto
is set with RTPROT_REDIRECT by rt6_fill_node() when kernel dumps
it. But in kernel the rt_cache protocol is still 0, which causes
the cache not to be matched and removed.
So the real reason is rt6i_protocol in the route is not set when
it is allocated. As David Ahern's suggestion, this patch is to
set rt6i_protocol properly in the route when it is installed and
remove the codes setting rtm_protocol according to rt6i_flags in
rt6_fill_node.
This is also an improvement to keep rt6i_protocol consistent with
rtm_protocol.
Fixes: c2ed1880fd ("net: ipv6: check route protocol when deleting routes")
Reported-by: Jianlin Shi <jishi@redhat.com>
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_loginfo structures are only passed as the seventh argument to
nf_log_trace, which is declared as const or stored in a local const
variable. Thus the nf_loginfo structures themselves can be const.
Done with the help of Coccinelle.
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct nf_loginfo i@p = { ... };
@ok1@
identifier r.i;
expression list[6] es;
position p;
@@
nf_log_trace(es,&i@p,...)
@ok2@
identifier r.i;
const struct nf_loginfo *e;
position p;
@@
e = &i@p
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
struct nf_loginfo e;
@@
e@i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct nf_loginfo i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
IPSec crypto offload depends on the protocol-specific
offload module (such as esp_offload.ko).
When the user installs an SA with crypto-offload, load
the offload module automatically, in the same way
that the protocol module is loaded (such as esp.ko)
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Both ip6_input_finish (non-GRO) and esp6_gro_receive (GRO) strip
the IPv6 header without adjusting skb->csum accordingly. As a
result CHECKSUM_COMPLETE breaks and "hw csum failure" is written
to the kernel log by netdev_rx_csum_fault (dev.c).
Fix skb->csum by substracting the checksum value of the pulled IPv6
header using a call to skb_postpull_rcsum.
This affects both transport and tunnel modes.
Note that the fix occurs far from the place that the header was
pulled. This is based on existing code, see:
ipv6_srh_rcv() in exthdrs.c and rawv6_rcv() in raw.c
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
xfrm6_transport_finish rebuilds the IPv6 header based on the
original one and pushes it back without fixing skb->csum.
Therefore, CHECKSUM_COMPLETE is no longer valid and the packet
gets dropped.
Fix skb->csum by calling skb_postpush_rcsum.
Note: A valid IPv4 header has checksum 0, unlike IPv6. Thus,
the change is not needed in the sibling xfrm4_transport_finish
function.
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Keep the device's reported ip_summed indication in case crypto
was offloaded by the device. Subtract the csum values of the
stripped parts (esp header+iv, esp trailer+auth_data) to keep
value correct.
Note: CHECKSUM_COMPLETE should be indicated only if skb->csum
has the post-decryption offload csum value.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Two minor conflicts in virtio_net driver (bug fix overlapping addition
of a helper) and MAINTAINERS (new driver edit overlapping revamp of
PHY entry).
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 3a3a4e3054.
inet6_add_protocol and inet6_del_protocol include casts that remove the
effect of the const annotation on their parameter, leading to possible
runtime crashes.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 67a51780ae ("ipv6: udp: leverage scratch area
helpers") udp6_recvmsg() read the skb len from the scratch area,
to avoid a cache miss.
But the UDP6 rx path support RFC 2675 UDPv6 jumbograms, and their
length exceeds the 16 bits available in the scratch area. As a side
effect the length returned by recvmsg() is:
<ingress datagram len> % (1<<16)
This commit addresses the issue allocating one more bit in the
IP6CB flags field and setting it for incoming jumbograms.
Such field is still in the first cacheline, so at recvmsg()
time we can check it and fallback to access skb->len if
required, without a measurable overhead.
Fixes: 67a51780ae ("ipv6: udp: leverage scratch area helpers")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to go through sk->sk_net to access the net namespace
and its sysctl variables because we allocate the sock and initialize
sk_net just a few lines earlier in the same routine.
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
prequeue is a tcp receive optimization that moves part of rx processing
from bh to process context.
This only works if the socket being processed belongs to a process that
is blocked in recv on that socket.
In practice, this doesn't happen anymore that often because nowadays
servers tend to use an event driven (epoll) model.
Even normal client applications (web browsers) commonly use many tcp
connections in parallel.
This has measureable impact only in netperf (which uses plain recv and
thus allows prequeue use) from host to locally running vm (~4%), however,
there were no changes when using netperf between two physical hosts with
ixgbe interfaces.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Discussion during NFWS 2017 in Faro has shown that the current
conntrack behaviour is unreasonable.
Even if conntrack module is loaded on behalf of a single net namespace,
its turned on for all namespaces, which is expensive. Commit
481fa37347 ("netfilter: conntrack: add nf_conntrack_default_on sysctl")
attempted to provide an alternative to the 'default on' behaviour by
adding a sysctl to change it.
However, as Eric points out, the sysctl only becomes available
once the module is loaded, and then its too late.
So we either have to move the sysctl to the core, or, alternatively,
change conntrack to become active only once the rule set requires this.
This does the latter, conntrack is only enabled when a rule needs it.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
We no longer place these on a list so they can be const.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This is a preparatory patch for adding fib support to the netdev family.
The netdev family receives the packets from ingress hook. At this point
we have no guarantee that the ip header is linear. So this patch
replaces ip_hdr with skb_header_pointer in order to address that
possible situation.
Signed-off-by: Pablo M. Bermudo Garay <pablombg@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When an early demuxed packet reaches __udp6_lib_lookup_skb(), the
sk reference is retrieved and used, but the relevant reference
count is leaked and the socket destructor is never called.
Beyond leaking the sk memory, if there are pending UDP packets
in the receive queue, even the related accounted memory is leaked.
In the long run, this will cause persistent forward allocation errors
and no UDP skbs (both ipv4 and ipv6) will be able to reach the
user-space.
Fix this by explicitly accessing the early demux reference before
the lookup, and properly decreasing the socket reference count
after usage.
Also drop the skb_steal_sock() in __udp6_lib_lookup_skb(), and
the now obsoleted comment about "socket cache".
The newly added code is derived from the current ipv4 code for the
similar path.
v1 -> v2:
fixed the __udp6_lib_rcv() return code for resubmission,
as suggested by Eric
Reported-by: Sam Edwards <CFSworks@gmail.com>
Reported-by: Marc Haber <mh+netdev@zugschlus.de>
Fixes: 5425077d73 ("net: ipv6: Add early demux handler for UDP unicast")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The inet6_protocol structure is only passed as the first argument to
inet6_add_protocol or inet6_del_protocol, both of which are declared as
const. Thus the inet6_protocol structure itself can be const.
Also drop __read_mostly where present on the newly const structures.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 2465 defines ipv6IfStatsOutFragFails as:
"The number of IPv6 datagrams that have been discarded
because they needed to be fragmented at this output
interface but could not be."
The existing implementation, instead, would increase the counter
twice in case we fail to allocate room for single fragments:
once for the fragment, once for the datagram.
This didn't look intentional though. In one of the two affected
affected failure paths, the double increase was simply a result
of a new 'goto fail' statement, introduced to avoid a skb leak.
The other path appears to be affected since at least 2.6.12-rc2.
Reported-by: Sabrina Dubroca <sdubroca@redhat.com>
Fixes: 1d325d217c ("ipv6: ip6_fragment: fix headroom tests and skb leak")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last (4th) argument of tcp_rcv_established() is redundant as it
always equals to skb->len and the skb itself is always passed as 2th
agrument. There is no reason to have it.
Signed-off-by: Ilya V. Matveychikov <matvejchikov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases, offset can overflow and can cause an infinite loop in
ip6_find_1stfragopt(). Make it unsigned int to prevent the overflow, and
cap it at IPV6_MAXPLEN, since packets larger than that should be invalid.
This problem has been here since before the beginning of git history.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After rcu conversions performance degradation in forward tests isn't that
noticeable anymore.
See next patch for some numbers.
A followup patcg could then also remove genid from the policies
as we do not cache bundles anymore.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
revert c386578f1c ("xfrm: Let the flowcache handle its size by default.").
Once we remove flow cache, we don't have a flow cache limit anymore.
We must not allow (virtually) unlimited allocations of xfrm dst entries.
Revert back to the old xfrm dst gc limits.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lennert reported a failure to add different mpls encaps in a multipath
route:
$ ip -6 route add 1234::/16 \
nexthop encap mpls 10 via fe80::1 dev ens3 \
nexthop encap mpls 20 via fe80::1 dev ens3
RTNETLINK answers: File exists
The problem is that the duplicate nexthop detection does not compare
lwtunnel configuration. Add it.
Fixes: 19e42e4515 ("ipv6: support for fib route lwtunnel encap attributes")
Signed-off-by: David Ahern <dsahern@gmail.com>
Reported-by: João Taveira Araújo <joao.taveira@gmail.com>
Reported-by: Lennert Buytenhek <buytenh@wantstofly.org>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Tested-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when the link for $DEV is down, this command succeeds but the
address is removed immediately by DAD (1):
ip addr add 1111::12/64 dev $DEV valid_lft 3600 preferred_lft 1800
In the same situation, this will succeed and not remove the address (2):
ip addr add 1111::12/64 dev $DEV
ip addr change 1111::12/64 dev $DEV valid_lft 3600 preferred_lft 1800
The comment in addrconf_dad_begin() when !IF_READY makes it look like
this is the intended behavior, but doesn't explain why:
* If the device is not ready:
* - keep it tentative if it is a permanent address.
* - otherwise, kill it.
We clearly cannot prevent userspace from doing (2), but we can make (1)
work consistently with (2).
addrconf_dad_stop() is only called in two cases: if DAD failed, or to
skip DAD when the link is down. In that second case, the fix is to avoid
deleting the address, like we already do for permanent addresses.
Fixes: 3c21edbd11 ("[IPV6]: Defer IPv6 device initialization until the link becomes ready.")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
This patch uses refcount_inc_not_zero() instead of
atomic_inc_not_zero_hint() due to absense of a _hint()
version of refcount API. If the hint() version must
be used, we might need to revisit API.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David Windsor <dwindsor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. This batch contains connection tracking updates for the cleanup
iteration path, patches from Florian Westphal:
X) Skip unconfirmed conntracks in nf_ct_iterate_cleanup_net(), just set
dying bit to let the CPU release them.
X) Add nf_ct_iterate_destroy() to be used on module removal, to kill
conntrack from all namespace.
X) Restart iteration on hashtable resizing, since both may occur at
the same time.
X) Use the new nf_ct_iterate_destroy() to remove conntrack with NAT
mapping on module removal.
X) Use nf_ct_iterate_destroy() to remove conntrack entries helper
module removal, from Liping Zhang.
X) Use nf_ct_iterate_cleanup_net() to remove the timeout extension
if user requests this, also from Liping.
X) Add net_ns_barrier() and use it from FTP helper, so make sure
no concurrent namespace removal happens at the same time while
the helper module is being removed.
X) Use NFPROTO_MAX in layer 3 conntrack protocol array, to reduce
module size. Same thing in nf_tables.
Updates for the nf_tables infrastructure:
X) Prepare usage of the extended ACK reporting infrastructure for
nf_tables.
X) Remove unnecessary forward declaration in nf_tables hash set.
X) Skip set size estimation if number of element is not specified.
X) Changes to accomodate a (faster) unresizable hash set implementation,
for anonymous sets and dynamic size fixed sets with no timeouts.
X) Faster lookup function for unresizable hash table for 2 and 4
bytes key.
And, finally, a bunch of asorted small updates and cleanups:
X) Do not hold reference to netdev from ipt_CLUSTER, instead subscribe
to device events and look up for index from the packet path, this
is fixing an issue that is present since the very beginning, patch
from Xin Long.
X) Use nf_register_net_hook() in ipt_CLUSTER, from Florian Westphal.
X) Use ebt_invalid_target() whenever possible in the ebtables tree,
from Gao Feng.
X) Calm down compilation warning in nf_dup infrastructure, patch from
stephen hemminger.
X) Statify functions in nftables rt expression, also from stephen.
X) Update Makefile to use canonical method to specify nf_tables-objs.
From Jike Song.
X) Use nf_conntrack_helpers_register() in amanda and H323.
X) Space cleanup for ctnetlink, from linzhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit b65ac44674 ("udp: try to avoid 2 cache miss on dequeue")
leveraged the scratched area helpers for UDP v4 but I forgot to
update accordingly the IPv6 code path.
This change extends the scratch area usage to the IPv6 code, synching
the two implementations and giving some performance benefit.
IPv6 is again almost on the same level of IPv4, performance-wide.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for extended error reporting.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In __ip6_datagram_connect(), reset sk->sk_v6_daddr and inet->dport if
error occurs.
In udp_v6_early_demux(), check for sk_state to make sure it is in
TCP_ESTABLISHED state.
Together, it makes sure unconnected UDP socket won't be considered as a
valid candidate for early demux.
v3: add TCP_ESTABLISHED state check in udp_v6_early_demux()
v2: fix compilation error
Fixes: 5425077d73 ("net: ipv6: Add early demux handler for UDP unicast")
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-06-23
1) Use memdup_user to spmlify xfrm_user_policy.
From Geliang Tang.
2) Make xfrm_dev_register static to silence a sparse warning.
From Wei Yongjun.
3) Use crypto_memneq to check the ICV in the AH protocol.
From Sabrina Dubroca.
4) Remove some unused variables in esp6.
From Stephen Hemminger.
5) Extend XFRM MIGRATE to allow to change the UDP encapsulation port.
From Antony Antony.
6) Include the UDP encapsulation port to km_migrate announcements.
From Antony Antony.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net): ipsec 2017-06-23
1) Fix xfrm garbage collecting when unregistering a netdevice.
From Hangbin Liu.
2) Fix NULL pointer derefernce when exiting a network namespace.
From Hangbin Liu.
3) Fix some error codes in pfkey to prevent a NULL pointer derefernce.
From Dan Carpenter.
4) Fix NULL pointer derefernce on allocation failure in pfkey.
From Dan Carpenter.
5) Adjust IPv6 payload_len to include extension headers. Otherwise
we corrupt the packets when doing ESP GRO on transport mode.
From Yossi Kuperman.
6) Set nhoff to the proper offset of the IPv6 nexthdr when doing ESP GRO.
From Yossi Kuperman.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The memory allocation size is controlled by user-space,
if it is too large just fail silently and return NULL,
not to mention there is a fallback allocation later.
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our customer encountered stuck NFS writes for blocks starting at specific
offsets w.r.t. page boundary caused by networking stack sending packets via
UFO enabled device with wrong checksum. The problem can be reproduced by
composing a long UDP datagram from multiple parts using MSG_MORE flag:
sendto(sd, buff, 1000, MSG_MORE, ...);
sendto(sd, buff, 1000, MSG_MORE, ...);
sendto(sd, buff, 3000, 0, ...);
Assume this packet is to be routed via a device with MTU 1500 and
NETIF_F_UFO enabled. When second sendto() gets into __ip_append_data(),
this condition is tested (among others) to decide whether to call
ip_ufo_append_data():
((length + fragheaderlen) > mtu) || (skb && skb_is_gso(skb))
At the moment, we already have skb with 1028 bytes of data which is not
marked for GSO so that the test is false (fragheaderlen is usually 20).
Thus we append second 1000 bytes to this skb without invoking UFO. Third
sendto(), however, has sufficient length to trigger the UFO path so that we
end up with non-UFO skb followed by a UFO one. Later on, udp_send_skb()
uses udp_csum() to calculate the checksum but that assumes all fragments
have correct checksum in skb->csum which is not true for UFO fragments.
When checking against MTU, we need to add skb->len to length of new segment
if we already have a partially filled skb and fragheaderlen only if there
isn't one.
In the IPv6 case, skb can only be null if this is the first segment so that
we have to use headersize (length of the first IPv6 header) rather than
fragheaderlen (length of IPv6 header of further fragments) for skb == NULL.
Fixes: e89e9cf539 ("[IPv4/IPv6]: UFO Scatter-gather approach")
Fixes: e4c5e13aa4 ("ipv6: Should use consistent conditional judgement for
ip6 fragment between __ip6_append_data and ip6_finish_output")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
very similar to commit dd99e425be ("udp: prefetch
rmem_alloc in udp_queue_rcv_skb()"), this allows saving a cache
miss when the BH is bottle-neck for UDP over ipv6 packet
processing, e.g. for small packets when a single RX NIC ingress
queue is in use.
Performances under flood when multiple NIC RX queues used are
unaffected, but when a single NIC rx queue is in use, this
gives ~8% performance improvement.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The per netns loopback_dev->ip6_ptr is unregistered and set to
NULL when its mtu is set to smaller than IPV6_MIN_MTU, this
leads to that we could set rt->rt6i_idev NULL after a
rt6_uncached_list_flush_dev() and then crash after another
call.
In this case we should just bring its inet6_dev down, rather
than unregistering it, at least prior to commit 176c39af29
("netns: fix addrconf_ifdown kernel panic") we always
override the case for loopback.
Thanks a lot to Andrey for finding a reliable reproducer.
Fixes: 176c39af29 ("netns: fix addrconf_ifdown kernel panic")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in both ipv4 and ipv6 code path, the ack packet received when
sk at TCP_NEW_SYN_RECV state is not filtered by socket filter or cgroup
filter since it is handled from tcp_child_process and never reaches the
tcp_filter inside tcp_v4_rcv or tcp_v6_rcv. Adding a tcp_filter hooks
here can make sure all the ingress tcp packet can be correctly filtered.
Signed-off-by: Chenbo Feng <fengc@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 242d3a49a2 ("ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf")
I assumed NETDEV_REGISTER and NETDEV_UNREGISTER are paired,
unfortunately, as reported by jeffy, netdev_wait_allrefs()
could rebroadcast NETDEV_UNREGISTER event until all refs are
gone.
We have to add an additional check to avoid this corner case.
For netdev_wait_allrefs() dev->reg_state is NETREG_UNREGISTERED,
for dev_change_net_namespace(), dev->reg_state is
NETREG_REGISTERED. So check for dev->reg_state != NETREG_UNREGISTERED.
Fixes: 242d3a49a2 ("ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf")
Reported-by: jeffy <jeffy.chen@rock-chips.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP6CB(skb)->nhoff is the offset of the nexthdr field in an IPv6
header, unless there are extension headers present, in which case
nhoff points to the nexthdr field of the last extension header.
In non-GRO code path, nhoff is set by ipv6_rcv before any XFRM code
is executed. Conversely, in GRO code path (when esp6_offload is loaded),
nhoff is not set. The following functions fail to read the correct value
and eventually the packet is dropped:
xfrm6_transport_finish
xfrm6_tunnel_input
xfrm6_rcv_tnl
Set nhoff to the proper offset of nexthdr in esp6_gro_receive.
Fixes: 7785bba299 ("esp: Add a software GRO codepath")
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
IPv6 payload length indicates the size of the payload, including any
extension headers.
In xfrm6_transport_finish, ipv6_hdr(skb)->payload_len is set to the
payload size only, regardless of the presence of any extension headers.
After ESP GRO transport mode decapsulation, ipv6_rcv trims the packet
according to the wrong payload_len, thus corrupting the packet.
Set payload_len to account for extension headers as well.
Fixes: 7785bba299 ("esp: Add a software GRO codepath")
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Two entries being added at the same time to the IFLA
policy table, whilst parallel bug fixes to decnet
routing dst handling overlapping with the dst gc removal
in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Netlink notifications on cache reports in ip6mr, in addition to the
existing mrt6msg sent to mroute6_sk.
Send RTM_NEWCACHEREPORT notifications to RTNLGRP_IPV6_MROUTE_R.
MSGTYPE, MIF_ID, SRC_ADDR and DST_ADDR Netlink attributes contain the
same data as their equivalent fields in the mrt6msg header.
PKT attribute is the packet sent to mroute6_sk, without the added
mrt6msg header.
Suggested-by: Ryan Halbrook <halbrook@arista.com>
Signed-off-by: Julien Gomes <julien@arista.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While commit 73ba57bfae ("ipv6: fix backtracking for throw routes")
does good job on error propagation to the fib_rules_lookup()
in fib rules core framework that also corrects throw routes
handling, it does not solve route reference leakage problem
happened when we return -EAGAIN to the fib_rules_lookup()
and leave routing table entry referenced in arg->result.
If rule with matched throw route isn't last matched in the
list we overwrite arg->result losing reference on throw
route stored previously forever.
We also partially revert commit ab997ad408 ("ipv6: fix the
incorrect return value of throw route") since we never return
routing table entry with dst.error == -EAGAIN when
CONFIG_IPV6_MULTIPLE_TABLES is on. Also there is no point
to check for RTF_REJECT flag since it is always set throw
route.
Fixes: 73ba57bfae ("ipv6: fix backtracking for throw routes")
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace first padding in the tcp_md5sig structure with a new flag field
and address prefix length so it can be specified when configuring a new
key for TCP MD5 signature. The tcpm_flags field will only be used if the
socket option is TCP_MD5SIG_EXT to avoid breaking existing programs, and
tcpm_prefixlen only when the TCP_MD5SIG_FLAG_PREFIX flag is set.
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Signed-off-by: Eric Mowat <mowat@arista.com>
Signed-off-by: Ivan Delalande <colona@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows the keys used for TCP MD5 signature to be used for whole
range of addresses, specified with a prefix length, instead of only one
address as it currently is.
Signed-off-by: Bob Gilligan <gilligan@arista.com>
Signed-off-by: Eric Mowat <mowat@arista.com>
Signed-off-by: Ivan Delalande <colona@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Same as ip_gre, geneve and vxlan, use key->tos as traffic class value.
CC: Peter Dawson <petedaws@gmail.com>
Fixes: 0e9a709560 ("ip6_tunnel, ip6_gre: fix setting of DSCP on
encapsulated packets”)
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Acked-by: Peter Dawson <peter.a.dawson@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DST_NOCACHE flag check has been removed from dst_release() and
dst_hold_safe() in a previous patch because all the dst are now ref
counted properly and can be released based on refcnt only.
Looking at the rest of the DST_NOCACHE use, all of them can now be
removed or replaced with other checks.
So this patch gets rid of all the DST_NOCACHE usage and remove this flag
completely.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that all the components have been changed to release dst based on
refcnt only and not depend on dst gc anymore, we can remove the
temporary flag DST_NOGC.
Note that we also need to remove the DST_NOCACHE check in dst_release()
and dst_hold_safe() because now all the dst are released based on refcnt
and behaves as DST_NOCACHE.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
icmp6 dst route is currently ref counted during creation and will be
freed by user during its call of dst_release(). So no need of a garbage
collector for it.
Remove all icmp6 dst garbage collector related code.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the previous preparation patches, we are ready to get rid of the
dst gc operation in ipv6 code and release dst based on refcnt only.
So this patch adds DST_NOGC flag for all IPv6 dst and remove the calls
to dst_free() and its related functions.
At this point, all dst created in ipv6 code do not use the dst gc
anymore and will be destroyed at the point when refcnt drops to 0.
Also, as icmp6 dst route is refcounted during creation and will be freed
by user during its call of dst_release(), there is no need to add this
dst to the icmp6 gc list as well.
Instead, we need to add it into uncached list so that when a
NETDEV_DOWN/NETDEV_UNREGISRER event comes, we can properly go through
these icmp6 dst as well and release the net device properly.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Similar as ipv4, ipv6 path also needs to call dst_hold_safe() when
necessary to avoid double free issue on the dst.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the intend of this patch series is to completely remove dst gc,
we need to call dst_dev_put() to release the reference to dst->dev
when removing routes from fib because we won't keep the gc list anymore
and will lose the dst pointer right after removing the routes.
Without the gc list, there is no way to find all the dst's that have
dst->dev pointing to the going-down dev.
Hence, we are doing dst_dev_put() immediately before we lose the last
reference of the dst from the routing code. The next dst_check() will
trigger a route re-lookup to find another route (if there is any).
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In IPv6 routing code, struct rt6_info is created for each static route
and RTF_CACHE route and inserted into fib6 tree. In both cases, dst
ref count is not taken.
As explained in the previous patch, this leads to the need of the dst
garbage collector.
This patch holds ref count of dst before inserting the route into fib6
tree and properly releases the dst when deleting it from the fib6 tree
as a preparation in order to fully get rid of dst gc later.
Also, correct fib6_age() logic to check dst->__refcnt to be 1 to indicate
no user is referencing the dst.
And remove dst_hold() in vrf_rt6_create() as ip6_dst_alloc() already puts
dst->__refcnt to 1.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing ipv4/6_blackhole_route() code generates a blackhole route
with dst->dev pointing to the passed in dst->dev.
It is not necessary to hold reference to the passed in dst->dev
because the packets going through this route are dropped anyway.
A loopback interface is good enough so that we don't need to worry about
releasing this dst->dev when this dev is going down.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In udp_v4/6_early_demux() code, we try to hold dst->__refcnt for
dst with DST_NOCACHE flag. This is because later in udp_sk_rx_dst_set()
function, we will try to cache this dst in sk for connected case.
However, a better way to achieve this is to not try to hold dst in
early_demux(), but in udp_sk_rx_dst_set(), call dst_hold_safe(). This
approach is also more consistant with how tcp is handling it. And it
will make later changes simpler.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ipv6 tx path, rcu_read_lock() is taken so that dst won't get freed
during the execution of ip6_fragment(). Hence, no need to hold dst in
it.
Signed-off-by: Wei Wang <weiwan@google.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When __ip6_tnl_rcv fails, the tun_dst won't be freed, so call
dst_release to free it in error code path.
Fixes: 8d79266bc4 ("ip6_tunnel: add collect_md mode to IPv6 tunnels")
CC: Alexei Starovoitov <ast@fb.com>
Tested-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
@@
expression SKB, LEN;
identifier fn = { skb_push, __skb_push, skb_push_rcsum };
@@
- fn(SKB, LEN)[0]
+ *(u8 *)fn(SKB, LEN)
Note that the last part there converts from push(...)[0] to the
more idiomatic *(u8 *)push(...).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions return void * and remove all the casts across
the tree, adding a (u8 *) cast only where the unsigned char pointer
was used directly, all done with the following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = {
skb_pull,
__skb_pull,
skb_pull_inline,
__pskb_pull_tail,
__pskb_pull,
pskb_pull
};
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = {
skb_pull,
__skb_pull,
skb_pull_inline,
__pskb_pull_tail,
__pskb_pull,
pskb_pull
};
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.
Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:
@@
expression SKB, LEN;
typedef u8;
identifier fn = { skb_put, __skb_put };
@@
- *(fn(SKB, LEN))
+ *(u8 *)fn(SKB, LEN)
@@
expression E, SKB, LEN;
identifier fn = { skb_put, __skb_put };
type T;
@@
- E = ((T *)(fn(SKB, LEN)))
+ E = fn(SKB, LEN)
which actually doesn't cover pskb_put since there are only three
users overall.
A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There were many places that my previous spatch didn't find,
as pointed out by yuan linyu in various patches.
The following spatch found many more and also removes the
now unnecessary casts:
@@
identifier p, p2;
expression len;
expression skb;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_zero(skb, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_zero(skb, len);
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, len);
|
-memset(p, 0, len);
)
@@
type t, t2;
identifier p, p2;
expression skb;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_zero(skb, sizeof(t));
)
... when != p
(
p2 = (t2)p;
-memset(p2, 0, sizeof(*p));
|
-memset(p, 0, sizeof(*p));
)
@@
expression skb, len;
@@
-memset(skb_put(skb, len), 0, len);
+skb_put_zero(skb, len);
Apply it to the tree (with one manual fixup to keep the
comment in vxlan.c, which spatch removed.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now when starting the dad work in addrconf_mod_dad_work, if the dad work
is idle and queued, it needs to hold ifa.
The problem is there's one gap in [1], during which if the pending dad work
is removed elsewhere. It will miss to hold ifa, but the dad word is still
idea and queue.
if (!delayed_work_pending(&ifp->dad_work))
in6_ifa_hold(ifp);
<--------------[1]
mod_delayed_work(addrconf_wq, &ifp->dad_work, delay);
An use-after-free issue can be caused by this.
Chen Wei found this issue when WARN_ON(!hlist_unhashed(&ifp->addr_lst)) in
net6_ifa_finish_destroy was hit because of it.
As Hannes' suggestion, this patch is to fix it by holding ifa first in
addrconf_mod_dad_work, then calling mod_delayed_work and putting ifa if
the dad_work is already in queue.
Note that this patch did not choose to fix it with:
if (!mod_delayed_work(delay))
in6_ifa_hold(ifp);
As with it, when delay == 0, dad_work would be scheduled immediately, all
addrconf_mod_dad_work(0) callings had to be moved under ifp->lock.
Reported-by: Wei Chen <weichen@redhat.com>
Suggested-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Weimer seems to have a glibc test-case which requires that
loopback interfaces does not get ICMP ratelimited. This was broken by
commit c0303efeab ("net: reduce cycles spend on ICMP replies that
gets rate limited").
An ICMP response will usually be routed back-out the same incoming
interface. Thus, take advantage of this and skip global ICMP
ratelimit when the incoming device is loopback. In the unlikely event
that the outgoing it not loopback, due to strange routing policy
rules, ICMP rate limiting still works via peer ratelimiting via
icmpv4_xrlim_allow(). Thus, we should still comply with RFC1812
(section 4.3.2.8 "Rate Limiting").
This seems to fix the reproducer given by Florian. While still
avoiding to perform expensive and unneeded outgoing route lookup for
rate limited packets (in the non-loopback case).
Fixes: c0303efeab ("net: reduce cycles spend on ICMP replies that gets rate limited")
Reported-by: Florian Weimer <fweimer@redhat.com>
Reported-by: "H.J. Lu" <hjl.tools@gmail.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reading /proc/net/snmp6 yields bogus values on 32 bit kernels.
Use "u64" instead of "unsigned long" in sizeof().
Fixes: 4a4857b1c8 ("proc: Reduce cache miss in snmp6_seq_show")
Signed-off-by: Christian Perle <christian.perle@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After moves the skb->dev and skb->protocol initialization into
ip6_output, setting the skb->dev inside ip6_fragment is unnecessary.
Fixes: 97a7a37a7b7b("ipv6: Initial skb->dev and skb->protocol in ip6_output")
Signed-off-by: Chenbo Feng <fengc@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two tcp_filter hooks in tcp_ipv6 ingress path currently.
One is at tcp_v6_rcv and another is in tcp_v6_do_rcv. It seems the
tcp_filter() call inside tcp_v6_do_rcv is redundent and some packet
will be filtered twice in this situation. This will cause trouble
when using eBPF filters to account traffic data.
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the initialization of skb->dev and skb->protocol from
ip6_finish_output2 to ip6_output. This can make the skb->dev and
skb->protocol information avalaible to the CGROUP eBPF filter.
Signed-off-by: Chenbo Feng <fengc@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipvlan code already knows how to detect when a duplicate address is
about to be assigned to an ipvlan device. However, that failure is not
propogated outward and leads to a silent failure.
Introduce a validation step at ip address creation time and allow device
drivers to register to validate the incoming ip addresses. The ipvlan
code is the first consumer. If it detects an address in use, we can
return an error to the user before beginning to commit the new ifa in
the networking code.
This can be especially useful if it is necessary to provision many
ipvlans in containers. The provisioning software (or operator) can use
this to detect situations where an ip address is unexpectedly in use.
Signed-off-by: Krister Johansen <kjlx@templeofstupid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While discussing the possible merits of clang warning about unused initialized
functions, I found one function that was clearly meant to be called but
never actually is.
__ila_hash_secret_init() initializes the hash value for the ila locator,
apparently this is intended to prevent hash collision attacks, but this ends
up being a read-only zero constant since there is no caller. I could find
no indication of why it was never called, the earliest patch submission
for the module already was like this. If my interpretation is right, we
certainly want to backport the patch to stable kernels as well.
I considered adding it to the ila_xlat_init callback, but for best effect
the random data is read as late as possible, just before it is first used.
The underlying net_get_random_once() is already highly optimized to avoid
overhead when called frequently.
Fixes: 7f00feaf10 ("ila: Add generic ILA translation facility")
Cc: stable@vger.kernel.org
Link: https://www.spinics.net/lists/kernel/msg2527243.html
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
DRAM supply shortage and poor memory pressure tracking in TCP
stack makes any change in SO_SNDBUF/SO_RCVBUF (or equivalent autotuning
limits) and tcp_mem[] quite hazardous.
TCPMemoryPressures SNMP counter is an indication of tcp_mem sysctl
limits being hit, but only tracking number of transitions.
If TCP stack behavior under stress was perfect :
1) It would maintain memory usage close to the limit.
2) Memory pressure state would be entered for short times.
We certainly prefer 100 events lasting 10ms compared to one event
lasting 200 seconds.
This patch adds a new SNMP counter tracking cumulative duration of
memory pressure events, given in ms units.
$ cat /proc/sys/net/ipv4/tcp_mem
3088 4117 6176
$ grep TCP /proc/net/sockstat
TCP: inuse 180 orphan 0 tw 2 alloc 234 mem 4140
$ nstat -n ; sleep 10 ; nstat |grep Pressure
TcpExtTCPMemoryPressures 1700
TcpExtTCPMemoryPressuresChrono 5209
v2: Used EXPORT_SYMBOL_GPL() instead of EXPORT_SYMBOL() as David
instructed.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa reported attempts to delete a bond device that is referenced in a
multipath route is hanging:
$ ifdown bond2 # ifupdown2 command that deletes virtual devices
unregister_netdevice: waiting for bond2 to become free. Usage count = 2
Steps to reproduce:
echo 1 > /proc/sys/net/ipv6/conf/all/ignore_routes_with_linkdown
ip link add dev bond12 type bond
ip link add dev bond13 type bond
ip addr add 2001:db8:2::0/64 dev bond12
ip addr add 2001:db8:3::0/64 dev bond13
ip route add 2001:db8:33::0/64 nexthop via 2001:db8:2::2 nexthop via 2001:db8:3::2
ip link del dev bond12
ip link del dev bond13
The root cause is the recent change to keep routes on a linkdown. Update
the check to detect when the device is unregistering and release the
route for that case.
Fixes: a1a22c1206 ("net: ipv6: Keep nexthop of multipath route on admin down")
Reported-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to move some TCP sysctls to net namespaces in the future.
tcp_window_scaling, tcp_sack and tcp_timestamps being fetched
from tcp_parse_options(), we need to pass an extra parameter.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network devices can allocate reasources and private memory using
netdev_ops->ndo_init(). However, the release of these resources
can occur in one of two different places.
Either netdev_ops->ndo_uninit() or netdev->destructor().
The decision of which operation frees the resources depends upon
whether it is necessary for all netdev refs to be released before it
is safe to perform the freeing.
netdev_ops->ndo_uninit() presumably can occur right after the
NETDEV_UNREGISTER notifier completes and the unicast and multicast
address lists are flushed.
netdev->destructor(), on the other hand, does not run until the
netdev references all go away.
Further complicating the situation is that netdev->destructor()
almost universally does also a free_netdev().
This creates a problem for the logic in register_netdevice().
Because all callers of register_netdevice() manage the freeing
of the netdev, and invoke free_netdev(dev) if register_netdevice()
fails.
If netdev_ops->ndo_init() succeeds, but something else fails inside
of register_netdevice(), it does call ndo_ops->ndo_uninit(). But
it is not able to invoke netdev->destructor().
This is because netdev->destructor() will do a free_netdev() and
then the caller of register_netdevice() will do the same.
However, this means that the resources that would normally be released
by netdev->destructor() will not be.
Over the years drivers have added local hacks to deal with this, by
invoking their destructor parts by hand when register_netdevice()
fails.
Many drivers do not try to deal with this, and instead we have leaks.
Let's close this hole by formalizing the distinction between what
private things need to be freed up by netdev->destructor() and whether
the driver needs unregister_netdevice() to perform the free_netdev().
netdev->priv_destructor() performs all actions to free up the private
resources that used to be freed by netdev->destructor(), except for
free_netdev().
netdev->needs_free_netdev is a boolean that indicates whether
free_netdev() should be done at the end of unregister_netdevice().
Now, register_netdevice() can sanely release all resources after
ndo_ops->ndo_init() succeeds, by invoking both ndo_ops->ndo_uninit()
and netdev->priv_destructor().
And at the end of unregister_netdevice(), we invoke
netdev->priv_destructor() and optionally call free_netdev().
Signed-off-by: David S. Miller <davem@davemloft.net>
When using CALIPSO with IPPROTO_UDP it is possible to trigger a GPF as the
IP header may have moved.
Also update the payload length after adding the CALIPSO option.
Signed-off-by: Richard Haines <richard_c_haines@btinternet.com>
Acked-by: Paul Moore <paul@paul-moore.com>
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit b699d00358.
As per Eric Dumazet, the pskb_may_pull() is a NOP in this
particular case, so the 'iph' reload is unnecessary.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since iptunnel_pull_header() can call pskb_may_pull(),
we must reload any pointer that was related to skb->head.
Fixes: a09a4c8dd1 ("tunnels: Remove encapsulation offloads on decap")
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander reported various KASAN messages triggered in recent kernels
The problem is that ping sockets should not use udp_poll() in the first
place, and recent changes in UDP stack finally exposed this old bug.
Fixes: c319b4d76b ("net: ipv4: add IPPROTO_ICMP socket kind")
Fixes: 6d0bfe2261 ("net: ipv6: Add IPv6 support to the ping socket.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Sasha Levin <alexander.levin@verizon.com>
Cc: Solar Designer <solar@openwall.com>
Cc: Vasiliy Kulikov <segoon@openwall.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Acked-By: Lorenzo Colitti <lorenzo@google.com>
Tested-By: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ip6_find_1stfragopt() fails and we return an error we have to free
up 'segs' because nobody else is going to.
Fixes: 2423496af3 ("ipv6: Prevent overrun when parsing v6 header options")
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_route_output() requires that the flowlabel contains the traffic
class for policy routing.
Commit 0e9a709560 ("ip6_tunnel, ip6_gre: fix setting of DSCP on
encapsulated packets") removed the code which previously added the
traffic class to the flowlabel.
The traffic class is added here because only route lookup needs the
flowlabel to contain the traffic class.
Fixes: 0e9a709560 ("ip6_tunnel, ip6_gre: fix setting of DSCP on encapsulated packets")
Signed-off-by: Liam McBirnie <liam.mcbirnie@boeing.com>
Acked-by: Peter Dawson <peter.a.dawson@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xfrm6_find_1stfragopt() may now return an error code and we must
not treat it as a length.
Fixes: 2423496af3 ("ipv6: Prevent overrun when parsing v6 header options")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack arg down to lwtunnel_build_state and the build_state callbacks.
Add messages for failures in lwtunnel_build_state, and add the extarg to
nla_parse where possible in the build_state callbacks.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass extack down to lwtunnel_valid_encap_type and
lwtunnel_valid_encap_type_attr. Add messages for unknown
or unsupported encap types.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are several places where we needlesly call nf_ct_iterate_cleanup,
we should instead iterate the full table at module unload time.
This is a leftover from back when the conntrack table got duplicated
per net namespace.
So rename nf_ct_iterate_cleanup to nf_ct_iterate_cleanup_net.
A later patch will then add a non-net variant.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Overlapping changes in drivers/net/phy/marvell.c, bug fix in 'net'
restricting a HW workaround alongside cleanups in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix addresses two problems in the way the DSCP field is formulated
on the encapsulating header of IPv6 tunnels.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195661
1) The IPv6 tunneling code was manipulating the DSCP field of the
encapsulating packet using the 32b flowlabel. Since the flowlabel is
only the lower 20b it was incorrect to assume that the upper 12b
containing the DSCP and ECN fields would remain intact when formulating
the encapsulating header. This fix handles the 'inherit' and
'fixed-value' DSCP cases explicitly using the extant dsfield u8 variable.
2) The use of INET_ECN_encapsulate(0, dsfield) in ip6_tnl_xmit was
incorrect and resulted in the DSCP value always being set to 0.
Commit 90427ef5d2 ("ipv6: fix flow labels when the traffic class
is non-0") caused the regression by masking out the flowlabel
which exposed the incorrect handling of the DSCP portion of the
flowlabel in ip6_tunnel and ip6_gre.
Fixes: 90427ef5d2 ("ipv6: fix flow labels when the traffic class is non-0")
Signed-off-by: Peter Dawson <peter.a.dawson@boeing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to return matched fib result when RTM_F_FIB_MATCH
flag is specified in RTM_GETROUTE request. This is useful for user-space
applications/controllers wanting to query a matching route.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add messages for non-obvious errors (e.g, no need to add text for malloc
failures or ENODEV failures). This mostly covers the annoying EINVAL errors
Some message strings violate the 80-columns but searchable strings need to
trump that rule.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey Konovalov and idaifish@gmail.com reported crashes caused by
one skb shared_info being overwritten from __ip6_append_data()
Andrey program lead to following state :
copy -4200 datalen 2000 fraglen 2040
maxfraglen 2040 alloclen 2048 transhdrlen 0 offset 0 fraggap 6200
The skb_copy_and_csum_bits(skb_prev, maxfraglen, data + transhdrlen,
fraggap, 0); is overwriting skb->head and skb_shared_info
Since we apparently detect this rare condition too late, move the
code earlier to even avoid allocating skb and risking crashes.
Once again, many thanks to Andrey and syzkaller team.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Reported-by: <idaifish@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Resolves warnings:
net/ipv6/esp6.c: In function ‘esp_ssg_unref’:
net/ipv6/esp6.c:121:10: warning: variable ‘seqhi’ set but not used [-Wunused-but-set-variable]
net/ipv6/esp6.c: In function ‘esp6_output_head’:
net/ipv6/esp6.c:227:21: warning: variable ‘esph’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
THe seg6_pernet_data variable was set but never used.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The build header functions are not used by any other code.
net/ipv6/fou6.c:36:5: warning: no previous prototype for ‘fou6_build_header’ [-Wmissing-prototypes]
net/ipv6/fou6.c:54:5: warning: no previous prototype for ‘gue6_build_header’ [-Wmissing-prototypes]
Need to do some code rearranging to satisfy different Kconfig possiblities.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This warning:
net/ipv6/ila/ila_lwt.c: In function ‘ila_output’:
net/ipv6/ila/ila_lwt.c:42:6: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
It looks like the code attempts to set propagate different error
values, but always returned -EINVAL.
Compile tested only. Needs review by original author.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This bit was introduced with commit 5a21232983 ("net: Support for
csum_bad in skbuff") to reduce the stack workload when processing RX
packets carrying a wrong Internet Checksum. Up to now, only one driver and
GRO core are setting it.
Suggested-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the udp memory accounting refactor, we don't need any more
to export the *udp*_queue_rcv_skb(). Make them static and fix
a couple of sparse warnings:
net/ipv4/udp.c:1615:5: warning: symbol 'udp_queue_rcv_skb' was not
declared. Should it be static?
net/ipv6/udp.c:572:5: warning: symbol 'udpv6_queue_rcv_skb' was not
declared. Should it be static?
Fixes: 850cbaddb5 ("udp: use it's own memory accounting schema")
Fixes: c915fe13cb ("udplite: fix NULL pointer dereference")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not use unsigned variables to see if it returns a negative
error or not.
Fixes: 2423496af3 ("ipv6: Prevent overrun when parsing v6 header options")
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP Timestamps option is defined in RFC 7323
Traditionally on linux, it has been tied to the internal
'jiffies' variable, because it had been a cheap and good enough
generator.
For TCP flows on the Internet, 1 ms resolution would be much better
than 4ms or 10ms (HZ=250 or HZ=100 respectively)
For TCP flows in the DC, Google has used usec resolution for more
than two years with great success [1]
Receive size autotuning (DRS) is indeed more precise and converges
faster to optimal window size.
This patch converts tp->tcp_mstamp to a plain u64 value storing
a 1 usec TCP clock.
This choice will allow us to upstream the 1 usec TS option as
discussed in IETF 97.
[1] https://www.ietf.org/proceedings/97/slides/slides-97-tcpm-tcp-options-for-low-latency-00.pdf
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
under udp flood the sk_receive_queue spinlock is heavily contended.
This patch try to reduce the contention on such lock adding a
second receive queue to the udp sockets; recvmsg() looks first
in such queue and, only if empty, tries to fetch the data from
sk_receive_queue. The latter is spliced into the newly added
queue every time the receive path has to acquire the
sk_receive_queue lock.
The accounting of forward allocated memory is still protected with
the sk_receive_queue lock, so udp_rmem_release() needs to acquire
both locks when the forward deficit is flushed.
On specific scenarios we can end up acquiring and releasing the
sk_receive_queue lock multiple times; that will be covered by
the next patch
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Track alignment in BPF verifier so that legitimate programs won't be
rejected on !CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS architectures.
2) Make tail calls work properly in arm64 BPF JIT, from Deniel
Borkmann.
3) Make the configuration and semantics Generic XDP make more sense and
don't allow both generic XDP and a driver specific instance to be
active at the same time. Also from Daniel.
4) Don't crash on resume in xen-netfront, from Vitaly Kuznetsov.
5) Fix use-after-free in VRF driver, from Gao Feng.
6) Use netdev_alloc_skb_ip_align() to avoid unaligned IP headers in
qca_spi driver, from Stefan Wahren.
7) Always run cleanup routines in BPF samples when we get SIGTERM, from
Andy Gospodarek.
8) The mdio phy code should bring PHYs out of reset using the shared
GPIO lines before invoking bus->reset(). From Florian Fainelli.
9) Some USB descriptor access endian fixes in various drivers from
Johan Hovold.
10) Handle PAUSE advertisements properly in mlx5 driver, from Gal
Pressman.
11) Fix reversed test in mlx5e_setup_tc(), from Saeed Mahameed.
12) Cure netdev leak in AF_PACKET when using timestamping via control
messages. From Douglas Caetano dos Santos.
13) netcp doesn't support HWTSTAMP_FILTER_ALl, reject it. From Miroslav
Lichvar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (52 commits)
ldmvsw: stop the clean timer at beginning of remove
ldmvsw: unregistering netdev before disable hardware
net: netcp: fix check of requested timestamping filter
ipv6: avoid dad-failures for addresses with NODAD
qed: Fix uninitialized data in aRFS infrastructure
mdio: mux: fix device_node_continue.cocci warnings
net/packet: fix missing net_device reference release
net/mlx4_core: Use min3 to select number of MSI-X vectors
macvlan: Fix performance issues with vlan tagged packets
net: stmmac: use correct pointer when printing normal descriptor ring
net/mlx5: Use underlay QPN from the root name space
net/mlx5e: IPoIB, Only support regular RQ for now
net/mlx5e: Fix setup TC ndo
net/mlx5e: Fix ethtool pause support and advertise reporting
net/mlx5e: Use the correct pause values for ethtool advertising
vmxnet3: ensure that adapter is in proper state during force_close
sfc: revert changes to NIC revision numbers
net: ch9200: add missing USB-descriptor endianness conversions
net: irda: irda-usb: fix firmware name on big-endian hosts
net: dsa: mv88e6xxx: add default case to switch
...
Every address gets added with TENTATIVE flag even for the addresses with
IFA_F_NODAD flag and dad-work is scheduled for them. During this DAD process
we realize it's an address with NODAD and complete the process without
sending any probe. However the TENTATIVE flags stays on the
address for sometime enough to cause misinterpretation when we receive a NS.
While processing NS, if the address has TENTATIVE flag, we mark it DADFAILED
and endup with an address that was originally configured as NODAD with
DADFAILED.
We can't avoid scheduling dad_work for addresses with NODAD but we can
avoid adding TENTATIVE flag to avoid this racy situation.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like commit 657831ffc3 ("dccp/tcp: do not inherit mc_list from parent")
we should clear ipv6_mc_list etc. for IPv6 sockets too.
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull RCU updates from Ingo Molnar:
"The main changes are:
- Debloat RCU headers
- Parallelize SRCU callback handling (plus overlapping patches)
- Improve the performance of Tree SRCU on a CPU-hotplug stress test
- Documentation updates
- Miscellaneous fixes"
* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (74 commits)
rcu: Open-code the rcu_cblist_n_lazy_cbs() function
rcu: Open-code the rcu_cblist_n_cbs() function
rcu: Open-code the rcu_cblist_empty() function
rcu: Separately compile large rcu_segcblist functions
srcu: Debloat the <linux/rcu_segcblist.h> header
srcu: Adjust default auto-expediting holdoff
srcu: Specify auto-expedite holdoff time
srcu: Expedite first synchronize_srcu() when idle
srcu: Expedited grace periods with reduced memory contention
srcu: Make rcutorture writer stalls print SRCU GP state
srcu: Exact tracking of srcu_data structures containing callbacks
srcu: Make SRCU be built by default
srcu: Fix Kconfig botch when SRCU not selected
rcu: Make non-preemptive schedule be Tasks RCU quiescent state
srcu: Expedite srcu_schedule_cbs_snp() callback invocation
srcu: Parallelize callback handling
kvm: Move srcu_struct fields to end of struct kvm
rcu: Fix typo in PER_RCU_NODE_PERIOD header comment
rcu: Use true/false in assignment to bool
rcu: Use bool value directly
...
Pull networking fixes from David Miller:
1) Fix multiqueue in stmmac driver on PCI, from Andy Shevchenko.
2) cdc_ncm doesn't actually fully zero out the padding area is
allocates on TX, from Jim Baxter.
3) Don't leak map addresses in BPF verifier, from Daniel Borkmann.
4) If we randomize TCP timestamps, we have to do it everywhere
including SYN cookies. From Eric Dumazet.
5) Fix "ethtool -S" crash in aquantia driver, from Pavel Belous.
6) Fix allocation size for ntp filter bitmap in bnxt_en driver, from
Dan Carpenter.
7) Add missing memory allocation return value check to DSA loop driver,
from Christophe Jaillet.
8) Fix XDP leak on driver unload in qed driver, from Suddarsana Reddy
Kalluru.
9) Don't inherit MC list from parent inet connection sockets, another
syzkaller spotted gem. Fix from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
dccp/tcp: do not inherit mc_list from parent
qede: Split PF/VF ndos.
qed: Correct doorbell configuration for !4Kb pages
qed: Tell QM the number of tasks
qed: Fix VF removal sequence
qede: Fix XDP memory leak on unload
net/mlx4_core: Reduce harmless SRIOV error message to debug level
net/mlx4_en: Avoid adding steering rules with invalid ring
net/mlx4_en: Change the error print to debug print
drivers: net: wimax: i2400m: i2400m-usb: Use time_after for time comparison
DECnet: Use container_of() for embedded struct
Revert "ipv4: restore rt->fi for reference counting"
net: mdio-mux: bcm-iproc: call mdiobus_free() in error path
net: ethernet: ti: cpsw: adjust cpsw fifos depth for fullduplex flow control
ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf
net: cdc_ncm: Fix TX zero padding
stmmac: pci: split out common_default_data() helper
stmmac: pci: RX queue routing configuration
stmmac: pci: TX and RX queue priority configuration
stmmac: pci: set default number of rx and tx queues
...
alloc_ila_locks seemed to c&p from alloc_bucket_locks allocation pattern
which is quite unusual. The default allocation size is 320 *
sizeof(spinlock_t) which is sub page unless lockdep is enabled when the
performance benefit is really questionable and not worth the subtle code
IMHO. Also note that the context when we call ila_init_net (modprobe or
a task creating a net namespace) has to be properly configured.
Let's just simplify the code and use kvmalloc helper which is a
transparent way to use kmalloc with vmalloc fallback.
Link: http://lkml.kernel.org/r/20170306103032.2540-5-mhocko@kernel.org
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For each netns (except init_net), we initialize its null entry
in 3 places:
1) The template itself, as we use kmemdup()
2) Code around dst_init_metrics() in ip6_route_net_init()
3) ip6_route_dev_notify(), which is supposed to initialize it after
loopback registers
Unfortunately the last one still happens in a wrong order because
we expect to initialize net->ipv6.ip6_null_entry->rt6i_idev to
net->loopback_dev's idev, thus we have to do that after we add
idev to loopback. However, this notifier has priority == 0 same as
ipv6_dev_notf, and ipv6_dev_notf is registered after
ip6_route_dev_notifier so it is called actually after
ip6_route_dev_notifier. This is similar to commit 2f460933f5
("ipv6: initialize route null entry in addrconf_init()") which
fixes init_net.
Fix it by picking a smaller priority for ip6_route_dev_notifier.
Also, we have to release the refcnt accordingly when unregistering
loopback_dev because device exit functions are called before subsys
exit functions.
Acked-by: David Ahern <dsahern@gmail.com>
Tested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Whole point of randomization was to hide server uptime, but an attacker
can simply start a syn flood and TCP generates 'old style' timestamps,
directly revealing server jiffies value.
Also, TSval sent by the server to a particular remote address vary
depending on syncookies being sent or not, potentially triggering PAWS
drops for innocent clients.
Lets implement proper randomization, including for SYNcookies.
Also we do not need to export sysctl_tcp_timestamps, since it is not
used from a module.
In v2, I added Florian feedback and contribution, adding tsoff to
tcp_get_cookie_sock().
v3 removed one unused variable in tcp_v4_connect() as Florian spotted.
Fixes: 95a22caee3 ("tcp: randomize tcp timestamp offsets for each connection")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Tested-by: Florian Westphal <fw@strlen.de>
Cc: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported a crash on init_net.ipv6.ip6_null_entry->rt6i_idev
since it is always NULL.
This is clearly wrong, we have code to initialize it to loopback_dev,
unfortunately the order is still not correct.
loopback_dev is registered very early during boot, we lose a chance
to re-initialize it in notifier. addrconf_init() is called after
ip6_route_init(), which means we have no chance to correct it.
Fix it by moving this initialization explicitly after
ipv6_add_dev(init_net.loopback_dev) in addrconf_init().
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS/OVS fixes for net
The following patchset contains a rather large batch of Netfilter, IPVS
and OVS fixes for your net tree. This includes fixes for ctnetlink, the
userspace conntrack helper infrastructure, conntrack OVS support,
ebtables DNAT target, several leaks in error path among other. More
specifically, they are:
1) Fix reference count leak in the CT target error path, from Gao Feng.
2) Remove conntrack entry clashing with a matching expectation, patch
from Jarno Rajahalme.
3) Fix bogus EEXIST when registering two different userspace helpers,
from Liping Zhang.
4) Don't leak dummy elements in the new bitmap set type in nf_tables,
from Liping Zhang.
5) Get rid of module autoload from conntrack update path in ctnetlink,
we don't need autoload at this late stage and it is happening with
rcu read lock held which is not good. From Liping Zhang.
6) Fix deadlock due to double-acquire of the expect_lock from conntrack
update path, this fixes a bug that was introduced when the central
spinlock got removed. Again from Liping Zhang.
7) Safe ct->status update from ctnetlink path, from Liping. The expect_lock
protection that was selected when the central spinlock was removed was
not really protecting anything at all.
8) Protect sequence adjustment under ct->lock.
9) Missing socket match with IPv6, from Peter Tirsek.
10) Adjust skb->pkt_type of DNAT'ed frames from ebtables, from
Linus Luessing.
11) Don't give up on evaluating the expression on new entries added via
dynset expression in nf_tables, from Liping Zhang.
12) Use skb_checksum() when mangling icmpv6 in IPv6 NAT as this deals
with non-linear skbuffs.
13) Don't allow IPv6 service in IPVS if no IPv6 support is available,
from Paolo Abeni.
14) Missing mutex release in error path of xt_find_table_lock(), from
Dan Carpenter.
15) Update maintainers files, Netfilter section. Add Florian to the
file, refer to nftables.org and change project status from Supported
to Maintained.
16) Bail out on mismatching extensions in element updates in nf_tables.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported a warning triggered by the rcu code:
------------[ cut here ]------------
WARNING: CPU: 1 PID: 5911 at lib/debugobjects.c:289
debug_print_object+0x175/0x210
ODEBUG: activate active (active state 1) object type: rcu_head hint:
(null)
Modules linked in:
CPU: 1 PID: 5911 Comm: a.out Not tainted 4.11.0-rc8+ #271
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16
dump_stack+0x192/0x22d lib/dump_stack.c:52
__warn+0x19f/0x1e0 kernel/panic.c:549
warn_slowpath_fmt+0xe0/0x120 kernel/panic.c:564
debug_print_object+0x175/0x210 lib/debugobjects.c:286
debug_object_activate+0x574/0x7e0 lib/debugobjects.c:442
debug_rcu_head_queue kernel/rcu/rcu.h:75
__call_rcu.constprop.76+0xff/0x9c0 kernel/rcu/tree.c:3229
call_rcu_sched+0x12/0x20 kernel/rcu/tree.c:3288
rt6_rcu_free net/ipv6/ip6_fib.c:158
rt6_release+0x1ea/0x290 net/ipv6/ip6_fib.c:188
fib6_del_route net/ipv6/ip6_fib.c:1461
fib6_del+0xa42/0xdc0 net/ipv6/ip6_fib.c:1500
__ip6_del_rt+0x100/0x160 net/ipv6/route.c:2174
ip6_del_rt+0x140/0x1b0 net/ipv6/route.c:2187
__ipv6_ifa_notify+0x269/0x780 net/ipv6/addrconf.c:5520
addrconf_ifdown+0xe60/0x1a20 net/ipv6/addrconf.c:3672
...
Andrey's reproducer program runs in a very tight loop, calling
'unshare -n' and then spawning 2 sets of 14 threads running random ioctl
calls. The relevant networking sequence:
1. New network namespace created via unshare -n
- ip6tnl0 device is created in down state
2. address added to ip6tnl0
- equivalent to ip -6 addr add dev ip6tnl0 fd00::bb/1
- DAD is started on the address and when it completes the host
route is inserted into the FIB
3. ip6tnl0 is brought up
- the new fixup_permanent_addr function restarts DAD on the address
4. exit namespace
- teardown / cleanup sequence starts
- once in a blue moon, lo teardown appears to happen BEFORE teardown
of ip6tunl0
+ down on 'lo' removes the host route from the FIB since the dst->dev
for the route is loobback
+ host route added to rcu callback list
* rcu callback has not run yet, so rt is NOT on the gc list so it has
NOT been marked obsolete
5. in parallel to 4. worker_thread runs addrconf_dad_completed
- DAD on the address on ip6tnl0 completes
- calls ipv6_ifa_notify which inserts the host route
All of that happens very quickly. The result is that a host route that
has been deleted from the IPv6 FIB and added to the RCU list is re-inserted
into the FIB.
The exit namespace eventually gets to cleaning up ip6tnl0 which removes the
host route from the FIB again, calls the rcu function for cleanup -- and
triggers the double rcu trace.
The root cause is duplicate DAD on the address -- steps 2 and 3. Arguably,
DAD should not be started in step 2. The interface is in the down state,
so it can not really send out requests for the address which makes starting
DAD pointless.
Since the second DAD was introduced by a recent change, seems appropriate
to use it for the Fixes tag and have the fixup function only start DAD for
addresses in the PREDAD state which occurs in addrconf_ifdown if the
address is retained.
Big thanks to Andrey for isolating a reliable reproducer for this problem.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since that change also made the nfrag function not necessary
for exports, remove it.
Fixes: 89a23c8b52 ("ip6_tunnel: Fix missing tunnel encapsulation limit option")
Signed-off-by: David S. Miller <davem@davemloft.net>
The IPv6 tunneling code tries to insert IPV6_TLV_TNL_ENCAP_LIMIT and
IPV6_TLV_PADN options when an encapsulation limit is defined (the
default is a limit of 4). An MTU adjustment is done to account for
these options as well. However, the options are never present in the
generated packets.
The issue appears to be a subtlety between IPV6_DSTOPTS and
IPV6_RTHDRDSTOPTS defined in RFC 3542. When the IPIP tunnel driver was
written, the encap limit options were included as IPV6_RTHDRDSTOPTS in
dst0opt of struct ipv6_txoptions. Later, ipv6_push_nfrags_opts was
(correctly) updated to require IPV6_RTHDR options when IPV6_RTHDRDSTOPTS
are to be used. This caused the options to no longer be included in v6
encapsulated packets.
The fix is to use IPV6_DSTOPTS (in dst1opt of struct ipv6_txoptions)
instead. IPV6_DSTOPTS do not have the additional IPV6_RTHDR requirement.
Fixes: 1df64a8569c7: ("[IPV6]: Add ip6ip6 tunnel driver.")
Fixes: 333fad5364d6: ("[IPV6]: Support several new sockopt / ancillary data in Advanced API (RFC3542)")
Signed-off-by: Craig Gallek <kraig@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter updates for your net-next
tree. A large bunch of code cleanups, simplify the conntrack extension
codebase, get rid of the fake conntrack object, speed up netns by
selective synchronize_net() calls. More specifically, they are:
1) Check for ct->status bit instead of using nfct_nat() from IPVS and
Netfilter codebase, patch from Florian Westphal.
2) Use kcalloc() wherever possible in the IPVS code, from Varsha Rao.
3) Simplify FTP IPVS helper module registration path, from Arushi Singhal.
4) Introduce nft_is_base_chain() helper function.
5) Enforce expectation limit from userspace conntrack helper,
from Gao Feng.
6) Add nf_ct_remove_expect() helper function, from Gao Feng.
7) NAT mangle helper function return boolean, from Gao Feng.
8) ctnetlink_alloc_expect() should only work for conntrack with
helpers, from Gao Feng.
9) Add nfnl_msg_type() helper function to nfnetlink to build the
netlink message type.
10) Get rid of unnecessary cast on void, from simran singhal.
11) Use seq_puts()/seq_putc() instead of seq_printf() where possible,
also from simran singhal.
12) Use list_prev_entry() from nf_tables, from simran signhal.
13) Remove unnecessary & on pointer function in the Netfilter and IPVS
code.
14) Remove obsolete comment on set of rules per CPU in ip6_tables,
no longer true. From Arushi Singhal.
15) Remove duplicated nf_conntrack_l4proto_udplite4, from Gao Feng.
16) Remove unnecessary nested rcu_read_lock() in
__nf_nat_decode_session(). Code running from hooks are already
guaranteed to run under RCU read side.
17) Remove deadcode in nf_tables_getobj(), from Aaron Conole.
18) Remove double assignment in nf_ct_l4proto_pernet_unregister_one(),
also from Aaron.
19) Get rid of unsed __ip_set_get_netlink(), from Aaron Conole.
20) Don't propagate NF_DROP error to userspace via ctnetlink in
__nf_nat_alloc_null_binding() function, from Gao Feng.
21) Revisit nf_ct_deliver_cached_events() to remove unnecessary checks,
from Gao Feng.
22) Kill the fake untracked conntrack objects, use ctinfo instead to
annotate a conntrack object is untracked, from Florian Westphal.
23) Remove nf_ct_is_untracked(), now obsolete since we have no
conntrack template anymore, from Florian.
24) Add event mask support to nft_ct, also from Florian.
25) Move nf_conn_help structure to
include/net/netfilter/nf_conntrack_helper.h.
26) Add a fixed 32 bytes scratchpad area for conntrack helpers.
Thus, we don't deal with variable conntrack extensions anymore.
Make sure userspace conntrack helper doesn't go over that size.
Remove variable size ct extension infrastructure now this code
got no more clients. From Florian Westphal.
27) Restore offset and length of nf_ct_ext structure to 8 bytes now
that wraparound is not possible any longer, also from Florian.
28) Allow to get rid of unassured flows under stress in conntrack,
this applies to DCCP, SCTP and TCP protocols, from Florian.
29) Shrink size of nf_conntrack_ecache structure, from Florian.
30) Use TCP_MAX_WSCALE instead of hardcoded 14 in TCP tracker,
from Gao Feng.
31) Register SYNPROXY hooks on demand, from Florian Westphal.
32) Use pernet hook whenever possible, instead of global hook
registration, from Florian Westphal.
33) Pass hook structure to ebt_register_table() to consolidate some
infrastructure code, from Florian Westphal.
34) Use consume_skb() and return NF_STOLEN, instead of NF_DROP in the
SYNPROXY code, to make sure device stats are not fooled, patch
from Gao Feng.
35) Remove NF_CT_EXT_F_PREALLOC this kills quite some code that we
don't need anymore if we just select a fixed size instead of
expensive runtime time calculation of this. From Florian.
36) Constify nf_ct_extend_register() and nf_ct_extend_unregister(),
from Florian.
37) Simplify nf_ct_ext_add(), this kills nf_ct_ext_create(), from
Florian.
38) Attach NAT extension on-demand from masquerade and pptp helper
path, from Florian.
39) Get rid of useless ip_vs_set_state_timeout(), from Aaron Conole.
40) Speed up netns by selective calls of synchronize_net(), from
Florian Westphal.
41) Silence stack size warning gcc in 32-bit arch in snmp helper,
from Florian.
42) Inconditionally call nf_ct_ext_destroy(), even if we have no
extensions, to deal with the NF_NAT_MANIP_SRC case. Patch from
Liping Zhang.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2017-04-28
Just one patch to fix a misplaced spin_unlock_bh in an error path.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In situations where an skb is paged, the transport header pointer and
tail pointer can be the same because the skb contents are in frags.
This results in ioctl(SIOCINQ/FIONREAD) incorrectly returning a
length of 0 when the length to receive is actually greater than zero.
skb->len is already correctly set in ip6_input_finish() with
pskb_pull(), so use skb->len as it always returns the correct result
for both linear and paged data.
Signed-off-by: Jamie Bainbridge <jbainbri@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andrey reported a out-of-bound access in ip6_tnl_xmit(), this
is because we use an ipv4 dst in ip6_tnl_xmit() and cast an IPv4
neigh key as an IPv6 address:
neigh = dst_neigh_lookup(skb_dst(skb),
&ipv6_hdr(skb)->daddr);
if (!neigh)
goto tx_err_link_failure;
addr6 = (struct in6_addr *)&neigh->primary_key; // <=== HERE
addr_type = ipv6_addr_type(addr6);
if (addr_type == IPV6_ADDR_ANY)
addr6 = &ipv6_hdr(skb)->daddr;
memcpy(&fl6->daddr, addr6, sizeof(fl6->daddr));
Also the network header of the skb at this point should be still IPv4
for 4in6 tunnels, we shold not just use it as IPv6 header.
This patch fixes it by checking if skb->protocol is ETH_P_IPV6: if it
is, we are safe to do the nexthop lookup using skb_dst() and
ipv6_hdr(skb)->daddr; if not (aka IPv4), we have no clue about which
dest address we can pick here, we have to rely on callers to fill it
from tunnel config, so just fall to ip6_route_output() to make the
decision.
Fixes: ea3dc9601b ("ip6_tunnel: Add support for wildcard tunnel endpoints.")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nowadays the NAT extension only stores the interface index
(used to purge connections that got masqueraded when interface goes down)
and pptp nat information.
Previous patches moved nf_ct_nat_ext_add to those places that need it.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Currently the nat extension is always attached as soon as nat module is
loaded. However, most NAT uses do not need the nat extension anymore.
Prepare to remove the add-nat-by-default by making those places that need
it attach it if its not present yet.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Current SYNPROXY codes return NF_DROP during normal TCP handshaking,
it is not friendly to caller. Because the nf_hook_slow would treat
the NF_DROP as an error, and return -EPERM.
As a result, it may cause the top caller think it meets one error.
For example, the following codes are from cfv_rx_poll()
err = netif_receive_skb(skb);
if (unlikely(err)) {
++cfv->ndev->stats.rx_dropped;
} else {
++cfv->ndev->stats.rx_packets;
cfv->ndev->stats.rx_bytes += skb_len;
}
When SYNPROXY returns NF_DROP, then netif_receive_skb returns -EPERM.
As a result, the cfv driver would treat it as an error, and increase
the rx_dropped counter.
So use NF_STOLEN instead of NF_DROP now because there is no error
happened indeed, and free the skb directly.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Defer registration of the synproxy hooks until the first SYNPROXY rule is
added. Also means we only register hooks in namespaces that need it.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Taking down the loopback device wreaks havoc on IPv6 routing. By
extension, taking down a VRF device wreaks havoc on its table.
Dmitry and Andrey both reported heap out-of-bounds reports in the IPv6
FIB code while running syzkaller fuzzer. The root cause is a dead dst
that is on the garbage list gets reinserted into the IPv6 FIB. While on
the gc (or perhaps when it gets added to the gc list) the dst->next is
set to an IPv4 dst. A subsequent walk of the ipv6 tables causes the
out-of-bounds access.
Andrey's reproducer was the key to getting to the bottom of this.
With IPv6, host routes for an address have the dst->dev set to the
loopback device. When the 'lo' device is taken down, rt6_ifdown initiates
a walk of the fib evicting routes with the 'lo' device which means all
host routes are removed. That process moves the dst which is attached to
an inet6_ifaddr to the gc list and marks it as dead.
The recent change to keep global IPv6 addresses added a new function,
fixup_permanent_addr, that is called on admin up. That function restarts
dad for an inet6_ifaddr and when it completes the host route attached
to it is inserted into the fib. Since the route was marked dead and
moved to the gc list, re-inserting the route causes the reported
out-of-bounds accesses. If the device with the address is taken down
or the address is removed, the WARN_ON in fib6_del is triggered.
All of those faults are fixed by regenerating the host route if the
existing one has been moved to the gc list, something that can be
determined by checking if the rt6i_ref counter is 0.
Fixes: f1705ec197 ("net: ipv6: Make address flushing on ifdown optional")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit a149e7c7ce ("ipv6: sr: add support for SRH injection through
setsockopt") introduced handling of IPV6_SRCRT_TYPE_4, but at the same
time restricted it to only IPV6_SRCRT_TYPE_0 and
IPV6_SRCRT_TYPE_4. Previously, ipv6_push_exthdr() and fl6_update_dst()
would also handle other values (ie STRICT and TYPE_2).
Restore previous source routing behavior, by handling IPV6_SRCRT_STRICT
and IPV6_SRCRT_TYPE_2 the same way as IPV6_SRCRT_TYPE_0 in
ipv6_push_exthdr() and fl6_update_dst().
Fixes: a149e7c7ce ("ipv6: sr: add support for SRH injection through setsockopt")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Reviewed-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ipv6 stub pointer is currently initialized before the ipv6
routing subsystem: a 3rd party can access and use such stub
before the routing data is ready.
Moreover, such pointer is not cleared in case of initialization
error, possibly leading to dangling pointers usage.
This change addresses the above moving the stub initialization
at the end of ipv6 init code.
Fixes: 5f81bd2e5d ("ipv6: export a stub for IPv6 symbols used by vxlan")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When recalculating the outer ICMPv6 checksum for a reverse path NATv6
such as ICMPV6_TIME_EXCEED nf_nat_icmpv6_reply_translation() was
accessing data beyond the headlen of the skb for non-linear skb. This
resulted in incorrect ICMPv6 checksum as garbage data was used.
Patch replaces csum_partial() with skb_checksum() which supports
non-linear skbs similar to nf_nat_icmp_reply_translation() from ipv4.
Signed-off-by: Dave Johnson <dave-kernel@centerclick.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
When arp_notify is set to 1 for either a specific interface or for 'all'
interfaces, gratuitous arp requests are sent. Since ndisc_notify is the
ipv6 equivalent to arp_notify, it should follow the same semantics.
Commit 4a6e3c5def ("net: ipv6: send unsolicited NA on admin up") sends
the NA on admin up. The final piece is checking devconf_all->ndisc_notify
in addition to the per device setting. Add it.
Fixes: 5cb04436ee ("ipv6: add knob to send unsolicited ND on link-layer address change")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A recent commit moved esp_alloc_tmp() out of a lock
protected region, but forgot to remove the unlock from
the error path. This patch removes the forgotten unlock.
While at it, remove some unneeded error assignments too.
Fixes: fca11ebde3 ("esp4: Reorganize esp_output")
Fixes: 383d0350f2 ("esp6: Reorganize esp_output")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Eric Dumazet