The MV64XXX I2C driver needs a clock in order to calculate the baud
rate factors. So add an clk to the clk tree. Also add the base DT
properties for kirkwood devices.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Conflicts:
arch/arm/mach-kirkwood/common.c
Commit 98d9986 (ARM: Kirkwood: Replace clock gating) and the fix 5fb2ce
(ARM: Kirkwood: clk_register_gate_fn: add fn assignment) introduced a custom
variant of clock gating which allows to define a function to be called
before gating the clock off.
This is used to disable the SATA and PCIe PHYs if the respective clocks
are unused after initialization.
However, of these two drivers, the SATA driver may be compiled as a module.
The driver re-enables the clocks at module init but the PHYs stay disabled.
Since the custom clock gating disabled the PHYs when gating the clock off,
it should also re-enable them when enabling the clock gate. This is done by
adding a second function that may be used to enable the PHYs.
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Marvell engineers tell us:
It seems that many units use the RUNIT clock.
SPI, UART, NAND, TWSI, ...
So it's not possible to clock gate it.
Currently the SPI, NAND and TWSI driver will clk_prepaure_enable()
this clk, but since we have no idea what ... is, and turning this clk
off results in a hard lock, unconditionally enable runit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
In commit:
98d9986 ARM: Kirkwood: Replace clock gating
the kirkwood clock gating has been reworked. A custom variant of
clock gating, that calls a custom function before gating the clock
off, has been introduced. However in clk_register_gate_fn() this
custom function "fn" is never assigned.
This patch adds the missing fn assignment.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@blackshift.org>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Olof Johansson <olof@lixom.net>
When the ethernet driver was built as a module, it would lock the
machine when loaded. At boot the ethernet clks are unused, so get
turned off. Later, when the module is loaded, the probe function
would access the hardware before the clock was restarted, and the
machine would lock. It has also been determined that when the clk is
turned off, the interface forgets its MAC address, which for most
systems, is set by the boot loader.
When the machine setup file creates a platform device for the
interface, prepare and enable the clock for the interface. This will
ensure it is not turned off. However, if the setup file only
instantiates one platform device, the other will have its clk
disabled, thus maybe saving a little power.
Report-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Add a varient of the basic clk-gate code. This variant calls a
function before gating the clock off. This function is used to disable
the SATA or PCIe PHY.
Now that all the drivers prepare and enable there clk as needed, there
is no need for the common code to keep track of which clocks need
gating on. Let the common clock framework turn off clocks which are
not used.
Buy using the added clk varient, when the clk framework turns off SATA
or PCIe clocks, we also disabled SATA and PCIe PHYs which were not
needed.
The function kirkwood_pcie_id() can now be called outside of __init
code, so remove this property for it, and functions it calls.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Prepare and enable the clocks when the board indicates the pcie buses
will be used.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some orion platforms can gate the XOR driver clock. If the clock
exisits, unable/disable it as appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some orion platforms support gating of the clock. If the clock exists
enable/disbale it as appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Some orion devices can gate the SDIO clock. If the clock exists,
enable/disable it as appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Not all orion platforms can gate the clock, but if it does exist,
enable/disable it as appropriate.
v2: Fix the name of the clkdev entry.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Not all platforms support gating the clock, so it is not an error if
the clock does not exist. However, if it does exist, we should
enable/disable it as appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The Orion kirkwood chips have a gatable clock per SATA channel. Add
code to get and enable this clk if it exists.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Let the machine pass to the platform which clock is used by the uart.
Enable the clock and use clk_get_rate() to determine its rate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Remove tclk from platform data. This makes the platform data
structure empty, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The t_clk is moved from the shared part of the ethernet driver into
the per port section. Each port can have its own gated clock, which it
needs to enable/disable, as oppossed to there being one clock shared
by all ports. In practice, only kirkwood supports this at the moment.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Remove now redundant tclk from SPI platform data. This makes the platform
data empty, so remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add tclk as a fixed rate clock for all platforms. In addition, on
kirkwood, add a gated clock for most of the clocks which can be gated.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Jamie Lentin <jm@lentin.co.uk>
[mturquette@linaro.org: removed redundant CLKDEV_LOOKUP from Kconfig]
[mturquette@linaro.org: removed redundant clk.h from mach-dove/common.c]
Signed-off-by: Mike Turquette <mturquette@linaro.org>
We need to absorb kirkwood_init() into kirkwood_dt_init() so that as we
convert drivers, we can remove the platform call, eg
kirkwood_rtc_init(). This maintains compatibility with non-fdt
configurations because they still call kirkwood_init() in common.c.
As drivers are converted, we will reinstate the 'static' qualifier in
common.c.
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The patch "ARM: orion: Consolidate USB platform setup code.", commit
4fcd3f374a broke USB on TS-7800 and
other orion5x boards, because the wrong type of PHY was being passed
to the EHCI driver in the platform data. Orion5x needs EHCI_PHY_ORION
and all the others want EHCI_PHY_NA.
Allow the mach- code to tell the generic plat-orion code which USB PHY
enum to place into the platform data.
Version 2: Rebase to v3.3-rc2.
Reported-by: Ambroz Bizjak <ambrop7@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Ambroz Bizjak <ambrop7@gmail.com>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=N2B4
-----END PGP SIGNATURE-----
Merge tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
New feature development
This adds support for new features, and contains stuff from most
platforms. A number of these patches could have fit into other
branches, too, but were small enough not to cause too much
confusion here.
* tag 'devel' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
mfd/db8500-prcmu: remove support for early silicon revisions
ARM: ux500: fix the smp_twd clock calculation
ARM: ux500: remove support for early silicon revisions
ARM: ux500: update register files
ARM: ux500: register DB5500 PMU dynamically
ARM: ux500: update ASIC detection for U5500
ARM: ux500: support DB8520
ARM: picoxcell: implement watchdog restart
ARM: OMAP3+: hwmod data: Add the default clockactivity for I2C
ARM: OMAP3: hwmod data: disable multiblock reads on MMC1/2 on OMAP34xx/35xx <= ES2.1
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP4
ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3
ARM: OMAP: hwmod data: Add support for AM35xx UART4/ttyO3
ARM: Orion: Remove address map info from all platform data structures
ARM: Orion: Get address map from plat-orion instead of via platform_data
ARM: Orion: mbus_dram_info consolidation
ARM: Orion: Consolidate the address map setup
ARM: Kirkwood: Add configuration for MPP12 as GPIO
ARM: Kirkwood: Recognize A1 revision of 6282 chip
ARM: ux500: update the MOP500 GPIO assignments
...
Hook these platforms restart code into the new restart hook rather than
using arch_reset().
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Move the *_mbus_dram_info structure into the orion platform and call it
orion_mbus_dram_info everywhere.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Recognize the Kirkwood 6282 revision A1 chip since products using
this chip are shipping now, such as the QNAP TS-x19P II devices.
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This change removes the interrupt resource. The driver does not use
it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Changing eg 0xffffffff to DMA_BIT_MASK(32) etc allows easier
side by side comparision of identical code which can be consolidated.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
This patch makes the various mach dirs that use the plat-orion time
code pass in timer and bridge addresses explicitly, instead of having
plat-orion get those values by including a mach dir include file --
the latter mechanism is problematic if you want to support multiple
ARM platforms in the same kernel image.
Signed-off-by: Lennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Use the machine-specific kexec_reinit hook to make sure
PCIe is enabled before starting a new kernel.
Signed-off-by: Eric Cooper <ecc@cmu.edu>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
According to the Marvell LSP, the Sample at Reset regiter bit 21 can be
used to detect TCLK on 6281 and 6282 devices.
This patch has only been tested on LaCie boards.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
multicomponent support added/changed some device name but added some typos,
breaking existing OpenRD Client support.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fairly simple conflicts, the most serious ones are the i.MX ones which I
suspect now need another rename.
Conflicts:
arch/arm/mach-mx2/clock_imx27.c
arch/arm/mach-mx2/devices.c
arch/arm/mach-omap2/board-rx51-peripherals.c
arch/arm/mach-omap2/board-zoom2.c
sound/soc/fsl/mpc5200_dma.c
sound/soc/fsl/mpc5200_dma.h
sound/soc/fsl/mpc8610_hpcd.c
sound/soc/pxa/spitz.c
This patch extends the ASoC API to allow sound cards to have more than one
CODEC and more than one platform DMA controller. This is achieved by dividing
some current ASoC structures that contain both driver data and device data into
structures that only either contain device data or driver data. i.e.
struct snd_soc_codec ---> struct snd_soc_codec (device data)
+-> struct snd_soc_codec_driver (driver data)
struct snd_soc_platform ---> struct snd_soc_platform (device data)
+-> struct snd_soc_platform_driver (driver data)
struct snd_soc_dai ---> struct snd_soc_dai (device data)
+-> struct snd_soc_dai_driver (driver data)
struct snd_soc_device ---> deleted
This now allows ASoC to be more tightly aligned with the Linux driver model and
also means that every ASoC codec, platform and (platform) DAI is a kernel
device. ASoC component private data is now stored as device private data.
The ASoC sound card struct snd_soc_card has also been updated to store lists
of it's components rather than a pointer to a codec and platform. The PCM
runtime struct soc_pcm_runtime now has pointers to all its components.
This patch adds DAPM support for ASoC multi-component and removes struct
snd_soc_socdev from DAPM core. All DAPM calls are now made on a card, codec
or runtime PCM level basis rather than using snd_soc_socdev.
Other notable multi-component changes:-
* Stream operations now de-reference less structures.
* close_delayed work() now runs on a DAI basis rather than looping all DAIs
in a card.
* PM suspend()/resume() operations can now handle N CODECs and Platforms
per sound card.
* Added soc_bind_dai_link() to bind the component devices to the sound card.
* Added soc_dai_link_probe() and soc_dai_link_remove() to probe and remove
DAI link components.
* sysfs entries can now be registered per component per card.
* snd_soc_new_pcms() functionailty rolled into dai_link_probe().
* snd_soc_register_codec() now does all the codec list and mutex init.
This patch changes the probe() and remove() of the CODEC drivers as follows:-
o Make CODEC driver a platform driver
o Moved all struct snd_soc_codec list, mutex, etc initialiasation to core.
o Removed all static codec pointers (drivers now support > 1 codec dev)
o snd_soc_register_pcms() now done by core.
o snd_soc_register_dai() folded into snd_soc_register_codec().
CS4270 portions:
Acked-by: Timur Tabi <timur@freescale.com>
Some TLV320aic23 and Cirrus platform fixes.
Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
TI CODEC and OMAP fixes
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Samsung platform and misc fixes :-
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Seungwhan Youn <sw.youn@samsung.com>
MPC8610 and PPC fixes.
Signed-off-by: Timur Tabi <timur@freescale.com>
i.MX fixes and some core fixes.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
J4740 platform fixes:-
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
CC: Tony Lindgren <tony@atomide.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Kevin Hilman <khilman@deeprootsystems.com>
CC: Sascha Hauer <s.hauer@pengutronix.de>
CC: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
CC: Kuninori Morimoto <morimoto.kuninori@renesas.com>
CC: Daniel Gloeckner <dg@emlix.com>
CC: Manuel Lauss <mano@roarinelk.homelinux.net>
CC: Mike Frysinger <vapier.adi@gmail.com>
CC: Arnaud Patard <apatard@mandriva.com>
CC: Wan ZongShun <mcuos.com@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (214 commits)
ALSA: hda - Add pin-fix for HP dc5750
ALSA: als4000: Fix potentially invalid DMA mode setup
ALSA: als4000: enable burst mode
ALSA: hda - Fix initial capsrc selection in patch_alc269()
ASoC: TWL4030: Capture route runtime DAPM ordering fix
ALSA: hda - Add PC-beep whitelist for an Intel board
ALSA: hda - More relax for pending period handling
ALSA: hda - Define AC_FMT_* constants
ALSA: hda - Fix beep frequency on IDT 92HD73xx and 92HD71Bxx codecs
ALSA: hda - Add support for HDMI HBR passthrough
ALSA: hda - Set Stream Type in Stream Format according to AES0
ALSA: hda - Fix Thinkpad X300 so SPDIF is not exposed
ALSA: hda - FIX to not expose SPDIF on Thinkpad X301, since it does not have the ability to use SPDIF
ASoC: wm9081: fix resource reclaim in wm9081_register error path
ASoC: wm8978: fix a memory leak if a wm8978_register fail
ASoC: wm8974: fix a memory leak if another WM8974 is registered
ASoC: wm8961: fix resource reclaim in wm8961_register error path
ASoC: wm8955: fix resource reclaim in wm8955_register error path
ASoC: wm8940: fix a memory leak if wm8940_register return error
ASoC: wm8904: fix resource reclaim in wm8904_register error path
...
This patch extends the kirkwood's PCIe support up to 2 controllers as in the 6282 devices.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Andrew Lunn