This is part of the work making gpio.c generic enough, the changes
include:
1. move IRQ handling of GPIO 0 and 1 outside (and back into irq.c)
2. pxa_init_gpio() accepts a range for muxed GPIO IRQs, and an IRQ
number for the muxed GPIOs
3. __gpio_is_occupied() and __gpio_is_inverted() are made inline,
and are moved into <mach/gpio.h> instead of generic gpio.c
Signed-off-by: Eric Miao <eric.miao@marvell.com>
1. Driver code where pxa_request_dma() is called will most likely
reference DMA registers as well, and it is really unnecessary
to include pxa-regs.h just for this. Move the definitions into
<mach/dma.h> and make relevant drivers include it instead of
<mach/pxa-regs.h>.
2. Introduce DMAC_REGS_VIRT as the virtual address base for these
DMA registers. This allows later processors to re-use the same
IP while registers may start at different I/O address.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Considering the header mess ATM, it is not always possible to include
the correct header files within board code. Let's keep this simple:
<mach/pxa25x.h> - for pxa25x based platforms
<mach/pxa27x.h> - for pxa27x based platforms
<mach/pxa300.h> - for pxa300 based platforms
<mach/pxa320.h> - for pxa320 based platforms
<mach/pxa930.h> - for pxa930 based platforms
NOTE:
1. one header one board file, they are not compatible (i.e. they have
conflicting definitions which won't compile if included together).
2. Unless strictly necessary, the following header files are considered
to be SoC files use _only_, and is not recommended to be included in
board code:
<mach/hardware.h>
<mach/pxa-regs.h>
<mach/pxa2xx-regs.h>
<mach/pxa3xx-regs.h>
<mach/mfp.h>
<mach/mfp-pxa2xx.h>
<mach/mfp-pxa25x.h>
<mach/mfp-pxa27x.h>
<mach/mfp-pxa3xx.h>
<mach/mfp-pxa300.h>
<mach/mfp-pxa320.h>
<mach/mfp-pxa930.h>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch adds support for the AM300 platform driver which uses the
E-Ink broadsheetfb display driver.
Cc: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch depends on otg_transceiver support in pxa27x_udc
(which is queued via linux-usb) to work.
It compiles also without it.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The only exclusive definitions are SSCR0_SCR and SSCR0_SerClkDiv(), loosen
that exclusive #ifdef .. #else .. #endif to allow other definitions to be
visible when slected multiple processors. This helps to pass the building
of pxa-ssp.c.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (29 commits)
Input: i8042 - add Dell Vostro 1510 to nomux list
Input: gtco - use USB endpoint API
Input: add support for Maple controller as a joystick
Input: atkbd - broaden the Dell DMI signatures
Input: HIL drivers - add MODULE_ALIAS()
Input: map_to_7segment.h - convert to __inline__ for userspace
Input: add support for enhanced rotary controller on pxa930 and pxa935
Input: add support for trackball on pxa930 and pxa935
Input: add da9034 touchscreen support
Input: ads7846 - strict_strtoul takes unsigned long
Input: make some variables and functions static
Input: add tsc2007 based touchscreen driver
Input: psmouse - add module parameters to control OLPC touchpad delays
Input: i8042 - add Gigabyte M912 netbook to noloop exception table
Input: atkbd - Samsung NC10 key repeat fix
Input: atkbd - add keyboard quirk for HP Pavilion ZV6100 laptop
Input: libps2 - handle 0xfc responses from devices
Input: add support for Wacom W8001 penabled serial touchscreen
Input: synaptics - report multi-taps only if supported by the device
Input: add joystick driver for Walkera WK-0701 RC transmitter
...
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (407 commits)
[ARM] pxafb: add support for overlay1 and overlay2 as framebuffer devices
[ARM] pxafb: cleanup of the timing checking code
[ARM] pxafb: cleanup of the color format manipulation code
[ARM] pxafb: add palette format support for LCCR4_PAL_FOR_3
[ARM] pxafb: add support for FBIOPAN_DISPLAY by dma braching
[ARM] pxafb: allow pxafb_set_par() to start from arbitrary yoffset
[ARM] pxafb: allow video memory size to be configurable
[ARM] pxa: add document on the MFP design and how to use it
[ARM] sa1100_wdt: don't assume CLOCK_TICK_RATE to be a constant
[ARM] rtc-sa1100: don't assume CLOCK_TICK_RATE to be a constant
[ARM] pxa/tavorevb: update board support (smartpanel LCD + keypad)
[ARM] pxa: Update eseries defconfig
[ARM] 5352/1: add w90p910-plat config file
[ARM] s3c: S3C options should depend on PLAT_S3C
[ARM] mv78xx0: implement GPIO and GPIO interrupt support
[ARM] Kirkwood: implement GPIO and GPIO interrupt support
[ARM] Orion: share GPIO IRQ handling code
[ARM] Orion: share GPIO handling code
[ARM] s3c: define __io using the typesafe version
[ARM] S3C64XX: Ensure CPU_V6 is selected
...
PXA27x and later processors support overlay1 and overlay2 on-top of the
base framebuffer (although under-neath the base is also possible). They
support palette and no-palette RGB formats, as well as YUV formats (only
available on overlay2). These overlays have dedicated DMA channels and
behave in a similar way as a framebuffer.
This heavily simplified and re-structured work is based on the original
pxafb_overlay.c (which is pending for mainline merge for a long time).
The major problems with this pxafb_overlay.c are (if you are interested
in the history):
1. heavily redundant (the control logics for overlay1 and overlay2 are
actually identical except for some small operations, which are now
abstracted into a 'pxafb_layer_ops' structure)
2. a lot of useless and un-tested code (two workarounds which are now
fixed on mature silicons)
3. cursorfb is actually useless, hardware cursor should not be used
this way, and the code was actually un-tested for a long time.
The code in this patch should be self-explanatory, I tried to add minimum
comments. As said, this is basically simplified, there are several things
still on the pending list:
1. palette mode is un-supported and un-tested (although re-using the
palette code of the base framebuffer is actually very easy now with
previous clean-up patches)
2. fb_pan_display for overlay(s) is un-supported
3. the base framebuffer can actually be abstracted by 'pxafb_layer' as
well, which will help further re-use of the code and keep a better
and consistent structure. (This is the reason I named it 'pxafb_layer'
instead of 'pxafb_overlay' or something alike)
See Documentation/fb/pxafb.txt for additional usage information.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Eric Miao <ycmiao@ycmiao-hp520.(none)>
1. introduce var_to_depth() to calculate the color depth including the
transparency bit
2. the conversion from 'fb_var_screeninfo' to LCCR3 BPP bits can be re-
used by overlays (in OVLxC1), thus an individual pxafb_var_to_bpp()
has been separated out.
3. pxafb_setmode() should really set the color bitfields correctly at
begining, introduce a pxafb_set_pixfmt() for this
4. allow user apps to specify color formats within fb_var_screeninfo,
and checking of this in pxafb_check_var() has been simplified as
below:
a) pxafb_var_to_bpp() should pass - which means a basically correct
bits_per_pixel and color depth setting
b) the RGBT bitfields are then forced into supported values by
pxafb_set_pixfmt()
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Eric Miao <ycmiao@ycmiao-hp520.(none)>
Add the palette format support for LCCR4_PAL_FOR_3, and fix the
issue of LCCR4 being never assigned.
Also remove the useless pxafb_set_truecolor().
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Eric Miao <ycmiao@ycmiao-hp520.(none)>
dma branching is enabled by extending the current setup_frame_dma()
function to allow a 2nd set of frame/palette dma descriptors to be
used.
As a result, pxafb_dma_buff.dma_desc[], pxafb_dma_buff.pal_desc[]
and pxafb_info.fdadr[] are doubled.
This allows maximum re-use of the current dma setup code, although
the pxafb_info.fdadr[xx] for FBRx register values looks a bit odd.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Eric Miao <ycmiao@ycmiao-hp520.(none)>
The amount of video memory size is decided according to the following
order:
1. <xres> x <yres> x <bits_per_pixel> by default, which is the backward
compatible way
2. size specified in platform data
3. size specified in module parameter 'options' string or specified in
kernel boot command line (see updated Documentation/fb/pxafb.txt)
And now since the memory is allocated from system memory, the pxafb_mmap
can be removed and the default fb_mmap() should be working all right.
Also, since we now have introduced the 'struct pxafb_dma_buff' for DMA
descriptors and palettes, the allocation can be separated cleanly.
NOTE: the LCD DMA actually supports chained transfer (i.e. page-based
transfers), to simplify the logic and keep the performance (with less
TLB misses when accessing from memory mapped user space), the memory
is allocated by alloc_pages_*() to ensures it's physical contiguous.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Eric Miao <ycmiao@ycmiao-hp520.(none)>
As Nicolas and Russell pointed out, CLOCK_TICK_RATE is no more
a constant on PXA when multiple processors and platforms are
selected, change TIMER_FREQ in rtc-sa1100.c into a variable.
Since the code to decide the clock tick rate is re-used from
timer.c, introduce a common get_clock_tick_rate() for this.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Changes made as suggested by Eric Miao (including fix to map_io
silly mistake!).
Originally designed by Intel, now sold by Crossbow (www.xbow.com).
Very little actually on board. The patch includes sensors and
similar as found on commonly occurring daughter boards.
Some of the drivers are not in mainline as yet as they are either
part of the IIO subsystem or need a lot of work before submission.
What is the position wrt to putting them in i2c board configs etc?
Support for these boards has been maintained outside the kernel
for a long time, but now that there is a good da9030 pmic driver
available the last major hurdle no longer exists.
All comments welcomed.
The Imote2's big brother (stargate2) will follow once any problems
with this one have been cleaned up and a few bits and bobs have
been added to the da903x driver. Hopefully the cc2420 driver will
get cleaned up and submitted in the not too distant future as
well.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Some smart panel requires a delay between command sequences, while PXA
LCD controller didn't provide such one, let's emulate this by software.
A software delay marker can be inserted into the command sequence, once
pxafb_smart_queue() detects this, it flushes the previous commands and
delay for a specified number of milliseconds.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
For smart panels (LCD panel with internal framebuffer), the following
LCCR3 register bits have different meanings than the parallel one:
LCCR3_PCP - controls the L_PCLK_WR polarity
LCCR3_HSP - controls the L_LCLK_A0 polarity
LCCR3_VSP - controls the L_FCLK_RD polarity
To keep minimum change to the original parallel timing, the .lcd_conn
flags and 'pxafb_mode_info.sync' are re-used to reflect this:
LCD_PCLK_EDGE_{RISE,FALL} - configures LCCR3_PCP
sync & FB_SYNC_{HOR,VERT}_HIGH_ACT - configures LCCR3_{HSP,VSP}
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patchset provides support for the TMIO based IO controller used in the
Toshiba e-series PDAs.
Signed-off-by: Ian Molton <spyro@f2s.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Fix kernel-doc notation to use correct syntax. Even though this should be
moved to where the function is actually implemented...
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/built-in.o: In function `pci_set_consistent_dma_mask':
hid-quirks.c:(.text+0x2664): multiple definition of `pci_set_consistent_dma_mask'
drivers/built-in.o: In function `pci_set_dma_mask':
hid-quirks.c:(.text+0x42c4): multiple definition of `pci_set_dma_mask'
because drivers/pci/pci.c was not seeing the definition disabling these
functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds HP iPAQ h5000's (h5400, h5500) basic definitions.
Kernel will able to boot, work via serial console, mount filesystems
placed on flashes and run USB gadgets (g_ether by default).
Other device drivers (frame buffer, LCD, touchscreen, backlight,
bluetooth, w1/battery, ...) are depend on SAMCOP and MediaQ
SoCs/MFDs, drivers to which will be submitted too, after massive
cleanups.
This machine will be used as "real user" for these new drivers.
This is an updated version of the patch, which contains fixes proposed on
linux-arm-kernel mailing list.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Milan Plzik <milan.plzik@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The charger enable gpio is straight (1 means draw from USB
Vbus, 0 mean do not draw). The USB Vbus sensing is inverted
(1 means no Vbus voltage sensed, 0 means Vbus voltage
present).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch implements Eric Miao's idea to detect the correct value of
sdram_rows by inspecting the MDCNFG register settings.
It is only tested on two pxa27x devices with 64MB RAM (magician and
hx4700) so far.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
GPIO3/GPIO4 are a bit special on pxa27x, since it depends on PCFR/PI2C_EN
bit, add their definitions here with comments.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
The optimal change would be to move the AC97 register definitions into
the AC97 driver, unfortunately, the registers are shared between several
files. Move them into a dedicated regs-ac97.h first.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Eric Miao