The FSF address is subject to change, thus remove it from the file. While here,
update a copyright line.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of using that member we prefer to use dma_dev which represents actual
struct device of the DMA device.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The support of the Moorestown was removed [1] from kernel long time ago. This
is just a follow up of that change.
[1] http://www.spinics.net/lists/platform-driver-x86/msg02948.html
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the driver was compiled with DMA support, but DMA channels weren't acquired
by some reason, mid_spi_dma_exit() will crash the kernel.
Fixes: 7063c0d942 (spi/dw_spi: add DMA support)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is no need to keep FSF address in the head of the file. While here, fix
few typos in the header.
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The reference manual from Rockchip claims this about the BSF (SPI Busy
Flag):
* 0 - SPI is idle or disabled
* 1 - SPI is actively transferring data
The above doesn't quite appear to be true. Specifically I found the
busy bit set when SPI was disabled. Let's change the WARN_ON() so we
only check the busy bit if the controller was enabled.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The wait_for_idle() could get unlucky and timeout too quickly.
Specifically, the old calculation was effectively:
timeout = jiffies + 1;
if (jiffies >= timeout) print warning;
From the above it should be obvious that if jiffies ticks in just the
wrong place then we'll have an effective timeout of 0.
Fix this by effectively changing the above ">=" to a ">". That gives
us an extra jiffy to finish.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
let "#define" statement keep same indentation. the old code layout is
pretty ugly.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
for command mode spi transfer, HW spec requires to do fifo reset work to
clear FIFO status.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
unify 'cmd_transfer' like 'pio_transfer' and 'dma_transfer' as void
function, and also change left_rx_word according to transfer result.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
in spi interrupt handler, we need check RX_IO_DMA status to ensure
rx fifo have received the specify count data.
if not set, the while statement in spi isr function will keep loop,
at last, make the kernel hang.
[The code is actually there in the interrupt handler but apparently it
needs the interrupt unmasking so the handler sees the status -- broonie]
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
the old codes check the cs-gpios, if the gpio number is 0 like:
<&gpio, 0, 0>, the driver will use the only hardware chipselect.
this is wrong because of_spi_register_master() can read property
cs-gpios from device node and set the spi master's cs number and
gpio cs automatically based on whether the cs-gpios is valid.
this patch fixes the beviour of CSR spi driver and move to a core
level supported way.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
Missing a blank line after declarations.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: macros should not use a trailing semicolon
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: else is not generally useful after a break or return
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: debugfs_remove_recursive(NULL) is safe this check is probably not required
WARNING: min() should probably be min_t(u32, rx_left, dw_readw(dws, DW_SPI_RXFLR))
WARNING: else is not generally useful after a break or return
WARNING: Missing a blank line after declarations
WARNING: void function return statements are not generally useful
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: Missing a blank line after declarations
WARNING: quoted string split across lines
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: Missing a blank line after declarations
WARNING: Prefer kcalloc over kzalloc with multiply
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the following checkpatch warnings.
WARNING: Missing a blank line after declarations
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@kernel.org>
device_add() expects that any memory allocated via devm_* API is only
done in the device's probe function.
Fix below boot warning:
WARNING: CPU: 1 PID: 1 at drivers/base/dd.c:286 driver_probe_device+0x2b4/0x2f4()
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.16.0-10474-g835c90b-dirty #160
[<c0016364>] (unwind_backtrace) from [<c001251c>] (show_stack+0x20/0x24)
[<c001251c>] (show_stack) from [<c04eaefc>] (dump_stack+0x7c/0x98)
[<c04eaefc>] (dump_stack) from [<c0023d4c>] (warn_slowpath_common+0x78/0x9c)
[<c0023d4c>] (warn_slowpath_common) from [<c0023d9c>] (warn_slowpath_null+0x2c/0x34)
[<c0023d9c>] (warn_slowpath_null) from [<c0302c60>] (driver_probe_device+0x2b4/0x2f4)
[<c0302c60>] (driver_probe_device) from [<c0302d90>] (__device_attach+0x50/0x54)
[<c0302d90>] (__device_attach) from [<c0300e60>] (bus_for_each_drv+0x54/0x9c)
[<c0300e60>] (bus_for_each_drv) from [<c0302958>] (device_attach+0x84/0x90)
[<c0302958>] (device_attach) from [<c0301f10>] (bus_probe_device+0x94/0xb8)
[<c0301f10>] (bus_probe_device) from [<c03000c0>] (device_add+0x434/0x4fc)
[<c03000c0>] (device_add) from [<c0342dd4>] (spi_add_device+0x98/0x164)
[<c0342dd4>] (spi_add_device) from [<c03444a4>] (spi_register_master+0x598/0x768)
[<c03444a4>] (spi_register_master) from [<c03446b4>] (devm_spi_register_master+0x40/0x80)
[<c03446b4>] (devm_spi_register_master) from [<c0346214>] (dw_spi_add_host+0x1a8/0x258)
[<c0346214>] (dw_spi_add_host) from [<c0346920>] (dw_spi_mmio_probe+0x1d4/0x294)
[<c0346920>] (dw_spi_mmio_probe) from [<c0304560>] (platform_drv_probe+0x3c/0x6c)
[<c0304560>] (platform_drv_probe) from [<c0302a98>] (driver_probe_device+0xec/0x2f4)
[<c0302a98>] (driver_probe_device) from [<c0302d3c>] (__driver_attach+0x9c/0xa0)
[<c0302d3c>] (__driver_attach) from [<c0300f0c>] (bus_for_each_dev+0x64/0x98)
[<c0300f0c>] (bus_for_each_dev) from [<c0302518>] (driver_attach+0x2c/0x30)
[<c0302518>] (driver_attach) from [<c0302134>] (bus_add_driver+0xdc/0x1f4)
[<c0302134>] (bus_add_driver) from [<c03035c8>] (driver_register+0x88/0x104)
[<c03035c8>] (driver_register) from [<c030445c>] (__platform_driver_register+0x58/0x6c)
[<c030445c>] (__platform_driver_register) from [<c0700f00>] (dw_spi_mmio_driver_init+0x18/0x20)
[<c0700f00>] (dw_spi_mmio_driver_init) from [<c0008914>] (do_one_initcall+0x90/0x1d4)
[<c0008914>] (do_one_initcall) from [<c06d7d90>] (kernel_init_freeable+0x178/0x248)
[<c06d7d90>] (kernel_init_freeable) from [<c04e687c>] (kernel_init+0x18/0xfc)
[<c04e687c>] (kernel_init) from [<c000ecd8>] (ret_from_fork+0x14/0x20)
Reported-by: Thor Thayer <tthayer@opensource.altera.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The FSF address is subject to change, thus remove it from the file. While here,
update a copyright line.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Instead of checking for device and vendor IDs inside probe function let's
provide a helper function via driver_data.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert system PM callbacks to use dev_pm_ops. In addition remove the PCI calls
related to a power state since the bus code cares about this already.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Nevertheless pci_bar is 0 let's explicitly use it when map IO regions. While
here, use pci_name instead of dev_name.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Let's print info message when controller is found and properly initialized.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
commit dd1053a93f ("spi/drivers: Enable build of drivers with
COMPILE_TEST") allows compile-testing drivers on platforms they're not
meant for.
However, adding "|| COMPILE_TEST" bypasses all other implicit dependencies
assumed by the platform dependencies before, like HAS_DMA.
If NO_DMA=y:
drivers/built-in.o: In function `atmel_spi_dma_unmap_xfer':
drivers/spi/spi-atmel.c:915: undefined reference to `dma_unmap_single'
drivers/spi/spi-atmel.c:918: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `atmel_spi_next_xfer_data':
drivers/spi/spi-atmel.c:690: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `atmel_spi_dma_map_xfer':
drivers/spi/spi-atmel.c:890: undefined reference to `dma_map_single'
drivers/spi/spi-atmel.c:893: undefined reference to `dma_mapping_error'
drivers/spi/spi-atmel.c:897: undefined reference to `dma_map_single'
drivers/spi/spi-atmel.c:900: undefined reference to `dma_mapping_error'
drivers/spi/spi-atmel.c:902: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `atmel_spi_probe':
drivers/spi/spi-atmel.c:1540: undefined reference to `dma_alloc_coherent'
drivers/spi/spi-atmel.c:1623: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `atmel_spi_remove':
drivers/spi/spi-atmel.c:1665: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `ep93xx_spi_dma_finish':
drivers/spi/spi-ep93xx.c:550: undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `ep93xx_spi_dma_prepare':
drivers/spi/spi-ep93xx.c:516: undefined reference to `dma_map_sg'
drivers/spi/spi-ep93xx.c:522: undefined reference to `dma_unmap_sg'
drivers/built-in.o: In function `omap2_mcspi_rx_dma':
drivers/spi/spi-omap2-mcspi.c:475: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `omap2_mcspi_txrx_dma':
drivers/spi/spi-omap2-mcspi.c:589: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `omap2_mcspi_transfer_one_message':
drivers/spi/spi-omap2-mcspi.c:1202: undefined reference to `dma_map_single'
drivers/spi/spi-omap2-mcspi.c:1204: undefined reference to `dma_mapping_error'
drivers/spi/spi-omap2-mcspi.c:1211: undefined reference to `dma_map_single'
drivers/spi/spi-omap2-mcspi.c:1213: undefined reference to `dma_mapping_error'
drivers/spi/spi-omap2-mcspi.c:1217: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `tegra_spi_deinit_dma_param':
drivers/spi/spi-tegra114.c:675: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `tegra_spi_copy_spi_rxbuf_to_client_rxbuf':
drivers/spi/spi-tegra114.c:415: undefined reference to `dma_sync_single_for_cpu'
drivers/spi/spi-tegra114.c:440: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `tegra_spi_copy_client_txbuf_to_spi_txbuf':
drivers/spi/spi-tegra114.c:381: undefined reference to `dma_sync_single_for_cpu'
drivers/spi/spi-tegra114.c:405: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `tegra_spi_start_dma_based_transfer':
drivers/spi/spi-tegra114.c:543: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `tegra_slink_deinit_dma_param':
drivers/spi/spi-tegra20-slink.c:705: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `tegra_slink_copy_spi_rxbuf_to_client_rxbuf':
drivers/spi/spi-tegra20-slink.c:427: undefined reference to `dma_sync_single_for_cpu'
drivers/spi/spi-tegra20-slink.c:452: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `tegra_slink_copy_client_txbuf_to_spi_txbuf':
drivers/spi/spi-tegra20-slink.c:393: undefined reference to `dma_sync_single_for_cpu'
drivers/spi/spi-tegra20-slink.c:417: undefined reference to `dma_sync_single_for_cpu'
drivers/built-in.o: In function `tegra_slink_start_dma_based_transfer':
drivers/spi/spi-tegra20-slink.c:561: undefined reference to `dma_sync_single_for_cpu'
Add dependencies on HAS_DMA to fix this.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make local symbol static, because this is used only in this file.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If our client is requesting a clock that is above the maximum clock
then the following division will result in 0:
rs->max_freq / rs->speed
We'll then program 0 into the SPI_BAUDR register. The Rockchip TRM
says: "If the value is 0, the serial output clock (sclk_out) is
disabled."
It's much better to end up with the fastest possible clock rather than
a clock that is off, so enforce a minimum value.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for MSIOF in:
- r8a7792 (R-Car V2H)
- r8a7793 (R-Car M2-N)
- r8a7794 (R-Car E2)
r8a7791 is now called "R-Car M2-W".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for QSPI in:
- r8a7792 (R-Car V2H)
- r8a7793 (R-Car M2-N)
- r8a7794 (R-Car E2)
r8a7791 is now called "R-Car M2-W".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The obvious fix after the commit d9c73bb8a3 "spi: dw: add support for gpio
controlled chip select". This patch fixes the issue by using locally defined
temporary variable.
Fixes: d9c73bb8a3 (spi: dw: add support for gpio controlled chip select)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org>
The commit 04f421e7 "spi: dw: use managed resources" changes drivers to use
managed functions, but seems wasn't properly tested in PCI case. The regs field
of struct dw_spi left uninitialized. Thus, kernel crashes when tries to access
to the SPI controller registers. This patch fixes the issue.
Fixes: 04f421e7 (spi: dw: use managed resources)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
The driver should not touch CS lines if SPI_NO_CS flag is set.
This patch fixes it as this functionality was broken accidentally
by
commit a88e34ea21 ("spi: davinci: add support to configure gpio cs through dt").
Fixes: a88e34ea21 ("spi: davinci: add support to configure gpio cs through dt")
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SPI host controller is the same as used in Baytrail, only the ACPI ID
is different so add this new ID to the list.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Fix a build failure introduced with commit 30670539b8
(spi: au1550: Fix bug in deallocation of memory)
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no need to unset driver data pointer at removal stage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Client drivers such as the ChomeOS EC driver sometimes use transfers with
no buffers and only a delay specified in order to allow a delay after the
assertion of /CS. Rather than require controller drivers handle this noop
case gracefully put checks in the core to ensure that we don't call into
the controller for such transfers.
Reported-by: Addy Ke <addy.ke@rock-chips.com>
Tested-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Broadcom 53xx ARM SoCs use bcma bus that contains various cores (AKA
devices). If board has a serial flash, it's connected over SPI and the
bcma bus includes a SPI controller. Example log from such a board:
bus0: Found chip with id 53010, rev 0x00 and package 0x02
(...)
bus0: Core 18 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0)
This patch adds a bcma driver for SPI core, it registers SPI master
controller and "bcm53xxspiflash" SPI device.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SPI PXA2XX core layer has dependency on common clock framework
to obtain information on host supported clock rate. Thus, we
setup the clock device in the PCI glue layer to enable PCI mode
host pass in the clock rate information.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The new Renesas R-Car Gen2 DMA Controller driver (rcar-dmac) requires
explicit configuration of the DMA slave bus width.
Hardcode the DMA transfer size to 4 bytes, as MSIOF DMA is limited to
32-bit words.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The new Renesas R-Car Gen2 DMA Controller driver (rcar-dmac) requires
explicit configuration of the DMA slave bus width.
Hardcode the DMA transfer size to 1 byte for both directions, as that's
the only supported configuration (16-bit DMA support was removed in
commit 9c5de2c175 ("spi: rspi: Remove
unused 16-bit DMA support")).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the devm_kasprintf() helper function instead of open coding
error-prone buffer handling and string formatting.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
If dmaengine_prep_slave_sg() or dmaengine_submit() fail, we may leak
unused DMA descriptors.
As per Documentation/dmaengine.txt, once a DMA descriptor has been
obtained, it must be submitted. Hence:
- First prepare and submit all DMA descriptors,
- Prepare the SPI controller for DMA,
- Start DMA by calling dma_async_issue_pending(),
- Make sure to call dmaengine_terminate_all() on all descriptors that
haven't completed.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
If dmaengine_prep_slave_sg() or dmaengine_submit() fail, we may leak
unused DMA descriptors.
As per Documentation/dmaengine.txt, once a DMA descriptor has been
obtained, it must be submitted. Hence:
- First prepare and submit all DMA descriptors,
- Prepare the SPI controller for DMA,
- Start DMA by calling dma_async_issue_pending(),
- Make sure to call dmaengine_terminate_all() on all descriptors that
haven't completed.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unused definition which cause the following warnings
drivers/spi/spi-omap-100k.c:73:0: warning: "WRITE" redefined [enabled by default]
include/linux/fs.h:193:0: note: this is the location of the previous definition
drivers/spi/spi-omap-100k.c:74:0: warning: "READ" redefined [enabled by default]
include/linux/fs.h:192:0: note: this is the location of the previous definition
Signed-off-by: Nick Krause <xerofoiffy@gmail.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is no need to init .owner field.
Based on the patch from Peter Griffin <peter.griffin@linaro.org>
"mmc: remove .owner field for drivers using module_platform_driver"
This patch removes the superflous .owner field for drivers which
use the module_platform_driver API, as this is overriden in
platform_driver_register anyway."
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
These are all arguments or fields that got added without updating the
kerneldoc comments.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The spi hangs waiting the completion of omap2_mcspi_rx_callback.
Signed-off-by: Jorge A. Ventura <jorge.araujo.ventura@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
This merge window brings a good size of cleanups on various
platforms. Among the bigger ones:
* Removal of Samsung s5pc100 and s5p64xx platforms. Both of these have
lacked active support for quite a while, and after asking around nobody
showed interest in keeping them around. If needed, they could be
resurrected in the future but it's more likely that we would prefer
reintroduction of them as DT and multiplatform-enabled platforms
instead.
* OMAP4 controller code register define diet. They defined a lot of registers
that were never actually used, etc.
* Move of some of the Tegra platform code (PMC, APBIO, fuse, powergate)
to drivers/soc so it can be shared with 64-bit code. This also converts them
over to traditional driver models where possible.
* Removal of legacy gpio-samsung driver, since the last users have been
removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some misc
cleanups, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQIcBAABAgAGBQJT5DYPAAoJEIwa5zzehBx37egQAIiatNiLLqZnfo3rwGADRz/a
POfPovktj68aPcobyzoyhFtToMqGvi9PpysyFTIQD2HJFG+5BtiIAuqtg0875zDe
EpBWgsfugrm0YktJWAtUerj60oAmNPbKfaEm1cOOWuM2lb2mV+QkRrwSTAgsqkT7
927BzMXKKBRPOVLL0RYhoF8EXa0Eg8kCqAHP8fJrzVYkRp+UrZJDnGiUP1XmWJN+
VXQMu5SEjcPMtqT7+tfX455RfREHJfBcJ1ZN/dPF8HMWDwClQG0lyc6hifh1MxwO
8DjIZNkfZeKqgDqVyC17re7pc7p8md5HL8WXbrKpK0A9vQ5bRexbPHxcwJ1T/C2Y
465H+st5XXbuzV1gbMwjK1/ycsH0tCyffckk8Yl/2e1Fs7GgPNbAELtTdl+5vV1Y
xmDXkyo/9WlRM3LQ23IGKwW7VzN86EfWVuShssfro0fO7xDdb4OOYLdQI+4bCG+h
ytQYun1vU32OEyNik5RVNQuZaMrv2c93a3bID4owwuPHPmYOPVUQaqnRX/0E51eA
aHZYbk2GlUOV3Kq5aSS4iyLg1Yj+I9/NeH9U+A4nc+PQ5FlgGToaVSCuYuw4DqbP
AAG+sqQHbkBMvDPobQz/yd1qZbAb4eLhGy11XK1t5S65rApWI55GwNXnvbyxqt8x
wpmxJTASGxcfuZZgKXm7
=gbcE
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"This merge window brings a good size of cleanups on various platforms.
Among the bigger ones:
- Removal of Samsung s5pc100 and s5p64xx platforms. Both of these
have lacked active support for quite a while, and after asking
around nobody showed interest in keeping them around. If needed,
they could be resurrected in the future but it's more likely that
we would prefer reintroduction of them as DT and
multiplatform-enabled platforms instead.
- OMAP4 controller code register define diet. They defined a lot of
registers that were never actually used, etc.
- Move of some of the Tegra platform code (PMC, APBIO, fuse,
powergate) to drivers/soc so it can be shared with 64-bit code.
This also converts them over to traditional driver models where
possible.
- Removal of legacy gpio-samsung driver, since the last users have
been removed (moved to pinctrl)
Plus a bunch of smaller changes for various platforms that sort of
dissapear in the diffstat for the above. clps711x cleanups, shmobile
header file refactoring/moves for multiplatform friendliness, some
misc cleanups, etc"
* tag 'cleanup-for-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (117 commits)
drivers: CCI: Correct use of ! and &
video: clcd-versatile: Depend on ARM
video: fix up versatile CLCD helper move
MAINTAINERS: Add sdhci-st file to ARCH/STI architecture
ARM: EXYNOS: Fix build breakge with PM_SLEEP=n
MAINTAINERS: Remove Kirkwood
ARM: tegra: Convert PMC to a driver
soc/tegra: fuse: Set up in early initcall
ARM: tegra: Always lock the CPU reset vector
ARM: tegra: Setup CPU hotplug in a pure initcall
soc/tegra: Implement runtime check for Tegra SoCs
soc/tegra: fuse: fix dummy functions
soc/tegra: fuse: move APB DMA into Tegra20 fuse driver
soc/tegra: Add efuse and apbmisc bindings
soc/tegra: Add efuse driver for Tegra
ARM: tegra: move fuse exports to soc/tegra/fuse.h
ARM: tegra: export apb dma readl/writel
ARM: tegra: Use a function to get the chip ID
ARM: tegra: Sort includes alphabetically
ARM: tegra: Move includes to include/soc/tegra
...
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 3.17. It contains:
- misc Cavium Octeon, BCM47xx, BCM63xx and Alchemy updates
- MIPS ptrace updates and cleanups
- various fixes that will also go to -stable
- a number of cleanups and small non-critical fixes.
- NUMA support for the Loongson 3.
- more support for MSA
- support for MAAR
- various FP enhancements and fixes"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (139 commits)
MIPS: jz4740: remove unnecessary null test before debugfs_remove
MIPS: Octeon: remove unnecessary null test before debugfs_remove_recursive
MIPS: ZBOOT: implement stack protector in compressed boot phase
MIPS: mipsreg: remove duplicate MIPS_CONF4_FTLBSETS_SHIFT
MIPS: Bonito64: remove a duplicate define
MIPS: Malta: initialise MAARs
MIPS: Initialise MAARs
MIPS: detect presence of MAARs
MIPS: define MAAR register accessors & bits
MIPS: mark MSA experimental
MIPS: Don't build MSA support unless it can be used
MIPS: consistently clear MSA flags when starting & copying threads
MIPS: 16 byte align MSA vector context
MIPS: disable preemption whilst initialising MSA
MIPS: ensure MSA gets disabled during boot
MIPS: fix read_msa_* & write_msa_* functions on non-MSA toolchains
MIPS: fix MSA context for tasks which don't use FP first
MIPS: init upper 64b of vector registers when MSA is first used
MIPS: save/disable MSA in lose_fpu
MIPS: preserve scalar FP CSR when switching vector context
...
A quiet release, more bug fixes than anything else. A few things do
stand out though:
- Updates to several drivers to move towards the standard GPIO chip
select handling in the core.
- DMA support for the SH MSIOF driver.
- Support for Rockchip SPI controllers (their first mainline
submission).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=u37g
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A quiet release, more bug fixes than anything else. A few things do
stand out though:
- updates to several drivers to move towards the standard GPIO chip
select handling in the core.
- DMA support for the SH MSIOF driver.
- support for Rockchip SPI controllers (their first mainline
submission)"
* tag 'spi-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (64 commits)
spi: davinci: use spi_device.cs_gpio to store gpio cs per spi device
spi: davinci: add support to configure gpio cs through dt
spi/pl022: Explicitly truncate large bitmask
spi/atmel: Fix pointer to int conversion warnings on 64 bit builds
spi: davinci: fix to support more than 2 chip selects
spi: topcliff-pch: don't hardcode PCI slot to get DMA device
spi: orion: fix incorrect handling of cell-index DT property
spi: orion: Fix error return code in orion_spi_probe()
spi/rockchip: fix error return code in rockchip_spi_probe()
spi/rockchip: remove redundant dev_err call in rockchip_spi_probe()
spi/rockchip: remove duplicated include from spi-rockchip.c
ARM: dts: fix the chip select gpios definition in the SPI nodes
spi: s3c64xx: Update binding documentation
spi: s3c64xx: use the generic SPI "cs-gpios" property
spi: s3c64xx: Revert "spi: s3c64xx: Added provision for dedicated cs pin"
spi: atmel: Use dmaengine_prep_slave_sg() API
spi: topcliff-pch: Update error messages for dmaengine_prep_slave_sg() API
spi: sh-msiof: Use correct device for DMA mapping with IOMMU
spi: sh-msiof: Handle dmaengine_prep_slave_single() failures gracefully
spi: rspi: Handle dmaengine_prep_slave_sg() failures gracefully
...
Rework Davinci SPI driver to store GPIO CS number in cs_gpio field
of SPI device structure (spi_device) for both DT and non-DT cases.
This will make Davinci SPI driver code simpler and allows to reuse
more SPI core functionality.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently driver supports only configuration of GPIO CS through
platform data. This patch enhances the driver to configure GPIO
CS through DT. Also update the DT binding documentation to
reflect the availability of cs-gpios.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When building on 64 bit architectures the use of bitwise negation generates
constants larger than 32 bits which won't fit in u32s used to represent
32 bit register values on the device. Explicitly cast to let the compiler
know that the higher bits are not significant and can be discarded.
Signed-off-by: Mark Brown <broonie@linaro.org>
On 64 bit systems integers are generally still 32 bit but long values and
pointers are usually 64 bit. GCC warns when casting a 64 bit pointer into
a 32 bit integer so cast to a long instead in order to avoid warnings.
Signed-off-by: Mark Brown <broonie@linaro.org>
Currently, the driver defines SPI_MAX_CHIPSELECT as 2 and
use per device array bytes_per_word based on this. This breaks
if num_chipselect per device is greater than 2. This patch
fix this and allocate memory for this array based on
num_chipselect.
It's preparation patch to enable GPIO CS feature for
Davinci SPI.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The DMA is a function 0 of the multifunction device where SPI host is attached.
Thus, we may avoid to hardcode PCI slot number.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In commit f814f9ac5a ("spi/orion: add device tree binding"), Device
Tree support was added to the spi-orion driver. However, this commit
reads the "cell-index" property, without taking into account the fact
that DT properties are big-endian encoded.
Since most of the platforms using spi-orion with DT have apparently
not used anything but cell-index = <0>, the problem was not
visible. But as soon as one starts using cell-index = <1>, the problem
becomes clearly visible, as the master->bus_num gets a wrong value
(actually it gets the value 0, which conflicts with the first bus that
has cell-index = <0>).
This commit fixes that by using of_property_read_u32() to read the
property value, which does the appropriate endianness conversion when
needed.
Fixes: f814f9ac5a ("spi/orion: add device tree binding")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org> # v3.6+
This patch adds helper functions to configure clock parents and rates
as specified through 'assigned-clock-parents', 'assigned-clock-rates'
DT properties for a clock provider or clock consumer device.
The helpers are now being called by the bus code for the platform, I2C
and SPI busses, before the driver probing and also in the clock core
after registration of a clock provider.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Fix to return a negative error code from the error handling case of
orion_spi_reset() instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fix to return -EINVAL from the error handling case instead of 0 when
failed to get fifo length.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Mark Brown <broonie@linaro.org>
The s3c64xx SPI driver uses a custom DT binding to specify
the GPIO used to drive the chip select (CS) line instead of
using the generic "cs-gpios" property already defined in:
Documentation/devicetree/bindings/spi/spi-bus.txt.
It's unfortunate that drivers are not using standard bindings
and creating custom ones instead but in most cases this can't
be changed without breaking Device Tree backward compatibility.
But in the case of this driver, its DT binding has been broken
for more than a year. Since after commit (dated June, 21 2013):
3146bee ("spi: s3c64xx: Added provision for dedicated cs pin")
DT backward compatibility was broken and nobody noticed until
now when the commit was reverted. So it seems to be safe to
change the binding to use the standard SPI "cs-gpios" property
instead of using a custom one just for this driver.
This patch also allows boards that don't use a GPIO pin for the
CS to work with the driver since the SPI core will take care of
setting spi->cs_gpio to -ENOENT if a board wants to use the built
in CS instead of a GPIO as explained in the SPI bus DT binding:
Documentation/devicetree/bindings/spi/spi-bus.txt.
For non-DT platforms, spi->cs_gpio will be set to -ENOENT as well
unless they specify a GPIO pin in their platform data. So both
native and GPIO chip select is also supported for legacy boards.
The above use case was what motivated commit 3146bee which broke
the DT binding backward compatibility in the first place.
Signed-off-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
[javier.martinez@collabora.co.uk: split changes and improve commit message]
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This reverts commit 3146beec21.
This commit resulted in a DT backward compatibility breakage.
Some devices use the native chip select (CS) instead of a GPIO
pin to drive the CS line. But the SPI driver made it mandatory
to specify a GPIO pin in the SPI device node controller-data.
So, using the built-in CS was not possible with the driver.
Commit 3146bee tried to fix that by adding a "cs-gpio" property
which could be defined in the SPI device node to make the driver
request the GPIO from the controller-data node.
Unfortunately that changed the old DT binding semantics since
now it's mandatory to have the "cs-gpio" property defined in
the SPI device node in order to use a GPIO pin to drive the CS.
As an example, a SPI device was defined before the commit with:
spi@12d20000 {
slave-node@0 {
controller-data {
cs-gpio = <&gpb1 2 0>;
}
}
}
and after the commit, the following DTS snippet must be used:
spi@12d20000 {
cs-gpio;
slave-node@0 {
controller-data {
cs-gpio = <&gpb1 2 0>;
}
}
}
So, after commit 3146bee the driver does not look for the GPIO
by default and it only looks for it if the top level "cs-gpio"
property is defined while the default used to be the opposite.
To always request the GPIO defined in the controller-data node.
This means that old FDT that of course didn't have this added
"cs-gpio" DT property in the SPI node broke after this change.
The offending commit can't be reverted cleanly since more than
a year have passed and other changes were made in the meantime
but this patch partially reverts the driver to it's original
state so old FDT can work again.
This patch will break Device Trees that were relying on the new
behavior of course but the patch should be reverted because:
a) There aren't DTS in mainline that use this new property.
b) They were relying on a behavior that broke DT compatibility.
c) The new binding is awkard, needing two properties with the
same name (cs-gpio) on different nodes is confusing at least.
d) The new property was not added to the DT binding doc:
Documentation/devicetree/bindings/spi/spi-samsung.txt
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the inline wrapper introduced by commit
16052827d9 ("dmaengine/dma_slave: introduce
inline wrappers").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 16052827d9 ("dmaengine/dma_slave:
introduce inline wrappers") changed the code to use the new API, but forgot
to update the error messages.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
--
v2:
- New
Signed-off-by: Mark Brown <broonie@linaro.org>
To function correctly in the presence of an IOMMU, the DMA buffers must be
mapped using the DMA channel's device instead of the MSIOF platform
device's device.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
As typically a shmobile SoC has less DMA channels than devices that can use
DMA, we may want to prioritize access to the DMA channels in the future.
This means that dmaengine_prep_slave_single() may start failing
arbitrarily.
Handle dmaengine_prep_slave_single() failures gracefully by falling back to
PIO. This requires moving DMA-specific configuration of the MSIOF device
after the call(s) to dmaengine_prep_slave_single().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
As typically a shmobile SoC has less DMA channels than devices that can use
DMA, we may want to prioritize access to the DMA channels in the future.
This means that dmaengine_prep_slave_sg() may start failing arbitrarily.
Handle dmaengine_prep_slave_sg() failures gracefully by falling back to
PIO.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
- removing s5p64x0 SoCs and s5pc100 SoC in mainline because
no more user and if it is required next time, it will be
supported with DT.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=CFpb
-----END PGP SIGNATURE-----
Merge tag 's5p-cleanup-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
Merge "Samsung cleanup 2nd version for S5P SoCs for 3.17" from Kukjin Kim:
Cleanup S5P SoCs for 3.17
- removing s5p64x0 SoCs and s5pc100 SoC in mainline because
no more user and if it is required next time, it will be
supported with DT.
* tag 's5p-cleanup-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
video: fbdev: s3c-fb: remove s5pc100 related fimd and fb codes
mtd: onenand: remove s5pc100 related onenand codes
spi: s3c64xx: remove s5pc100 related spi codes
gpio: samsung: remov s5pc100 related gpio codes
ARM: S5PC100: no more support S5PC100 SoC
video: fbdev: s3c-fb: remove s5p64x0 related fimd codes
spi: s3c64xx: remove s5p64x0 related spi codes
gpio: samsung: remove s5p64x0 related gpio codes
ARM: S5P64X0: no more support S5P6440 and S5P6450 SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
This patch removes sp5c100 related spi because of no more support
s5pc100 SoC.
Cc: Mark Brown <broonie@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Currently the cadence SPI driver does the SPI clock configuration (setup CPOL
and CPHA) in the prepare_transfer_hardware() callback. The
prepare_transfer_hardware() callback is only called though when the controller
transitions from a idle state to a non-idle state. Such a transitions happens
when the message queue goes from empty to non-empty. If multiple messages from
different SPI slaves with different clock settings are in the message queue the
clock settings will not be properly updated when switching from one slave device
to another. Instead do the updating of the clock configuration in the
prepare_message() callback which will be called for each individual message.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
It seems that the cadence SPI controller does not immediately change the clock
polarity setting when writing the CR register. Instead the change is delayed
until the next transfer starts. This happens after the chip select line has
already been asserted. As a result the first transfer after a clock polarity
change will generate spurious clock transitions which typically results in the
SPI slave not being able to properly understand the message. Toggling the ER
register seems to cause the SPI controller to apply the clock polarity changes,
so implement this as a workaround to fix the issue.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
According to Documentation/dmaengine.txt, scatterlists must be mapped
using the DMA struct device.
However, "dma_chan.dev->device" is the sysfs class device's device.
Use "dma_chan.device->dev" instead, which is the real DMA device's device.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
According to Documentation/DMA-API.txt, dma_map_sg() returns 0 on failure.
As spi_map_buf() returns an error code, convert zero into -ENOMEM.
Keep the existing check for negative numbers just in case.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Olof Johansson pointed out that usually the company name is picked as
namespace prefix to specific properties. So expect "energymicro,location"
but fall back to the previously introduced name "efm32,location".
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Xilinx SPI driver initializes the bus_num field of the SPI master to
pdev->dev.id. pdev->dev.id is always 0 for platform devices which causes bus
number conflicts for the SPI controller when creating multiple device instances
of the driver. Instead use pdev->id which will have the assignt platform device
id. If the device is instantiated via devicetree pdev->id is -1 which will cause
the SPI core to dynamically assign a id (or use the id defined via a alias in
the devicetree).
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
As of commit ab116a4df4 ("dmaengine:
shdma: fix a build failure on platforms with no DMA support"), the DMA
filter function shdma_chan_filter() is sufficiently abstracted to allow
building without DMA support. Hence drop the SH_DMAE_BASE dependency on
SUPERH.
Also increase build coverage by allowing the driver to be enabled if
COMPILE_TEST=y.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
If NO_DMA=y:
drivers/built-in.o: In function `sh_msiof_release_dma':
spi-sh-msiof.c:(.text+0x23cbfe): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sh_msiof_request_dma':
spi-sh-msiof.c:(.text+0x23cd5e): undefined reference to `dma_map_single'
spi-sh-msiof.c:(.text+0x23cd70): undefined reference to `dma_mapping_error'
spi-sh-msiof.c:(.text+0x23cdca): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `sh_msiof_dma_once':
spi-sh-msiof.c:(.text+0x23d450): undefined reference to `dma_sync_single_for_cpu'
spi-sh-msiof.c:(.text+0x23d5ea): undefined reference to `dma_sync_single_for_cpu'
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch removes s5p64x0 related spi because of no more support for
s5p64x0 SoCs. Meanwhile, cleanup SPI DT bindings for s5p6440-spi, it
should be s5p64x0-spi instead.
Cc: Mark Brown <broonie@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
rspi_release_dma() doesn't need access to any fields in the driver private
data, except for the pointer to the SPI master object. Hence just pass the
needed pointer.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Introduced by commit 8b983e90ea ("spi: rspi:
Extract rspi_common_transfer()"), which removed its users.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch introduces the use of devm_ioremap and removes the iounmaps
in the probe and remove functions. Also, the labels are renamed to
preserve ordering.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
Without the dependencies for the accessors the driver can be enabled on
architectures where it will fail to build.
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes a bug on the deallocation of memory allocated using
request_mem_region, by using release_mem_region instead of
release_resource and kfree.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to facilitate understanding, rockchip SPI controller IP design
looks similar in its registers to designware. But IC implementation
is different from designware, So we need a dedicated driver for Rockchip
RK3XXX SoCs integrated SPI. The main differences:
- dma request line: rockchip SPI controller have two DMA request line
for tx and rx.
- Register offset:
RK3288 dw
SPI_CTRLR0 0x0000 0x0000
SPI_CTRLR1 0x0004 0x0004
SPI_SSIENR 0x0008 0x0008
SPI_MWCR NONE 0x000c
SPI_SER 0x000c 0x0010
SPI_BAUDR 0x0010 0x0014
SPI_TXFTLR 0x0014 0x0018
SPI_RXFTLR 0x0018 0x001c
SPI_TXFLR 0x001c 0x0020
SPI_RXFLR 0x0020 0x0024
SPI_SR 0x0024 0x0028
SPI_IPR 0x0028 NONE
SPI_IMR 0x002c 0x002c
SPI_ISR 0x0030 0x0030
SPI_RISR 0x0034 0x0034
SPI_TXOICR NONE 0x0038
SPI_RXOICR NONE 0x003c
SPI_RXUICR NONE 0x0040
SPI_MSTICR NONE 0x0044
SPI_ICR 0x0038 0x0048
SPI_DMACR 0x003c 0x004c
SPI_DMATDLR 0x0040 0x0050
SPI_DMARDLR 0x0044 0x0054
SPI_TXDR 0x0400 NONE
SPI_RXDR 0x0800 NONE
SPI_IDR NONE 0x0058
SPI_VERSION NONE 0x005c
SPI_DR NONE 0x0060
- register configuration:
such as SPI_CTRLRO in rockchip SPI controller:
cr0 = (CR0_BHT_8BIT << CR0_BHT_OFFSET)
| (CR0_SSD_ONE << CR0_SSD_OFFSET);
cr0 |= (rs->n_bytes << CR0_DFS_OFFSET);
cr0 |= ((rs->mode & 0x3) << CR0_SCPH_OFFSET);
cr0 |= (rs->tmode << CR0_XFM_OFFSET);
cr0 |= (rs->type << CR0_FRF_OFFSET);
For more information, see RK3288 chip manual.
- Wait for idle: Must ensure that the FIFO data has been sent out
before the next transfer.
Signed-off-by: addy ke <addy.ke@rock-chips.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit id 2bd16e3e23
(spi: omap2-mcspi: Do not configure the controller
on each transfer unless needed) does its job too
well so omap2_mcspi_setup_transfer() isn't called
even when an SPI slave driver changes 'spi->mode'.
The result is that the mode requested by the SPI
slave driver never takes effect.
Fix this by adding the 'mode' member to the
omap2_mcspi_cs structure which holds the mode
value that the hardware is configured for.
When the SPI slave driver changes 'spi->mode'
it will be different than the value of this new
member and the SPI master driver will know that
the hardware must be reconfigured (by calling
omap2_mcspi_setup_transfer()).
Fixes: 2bd16e3e23 (spi: omap2-mcspi: Do not configure the controller on each transfer unless needed)
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
ret is unused when CONFIG_FSL_SOC defined,
so return ret instead of -ENOMEM when the
kzalloc fails to avoid it.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add DMA support to the MSIOF driver using platform data.
As MSIOF DMA is limited to 32-bit words (requiring byte/wordswapping for
smaller wordsizes), and the group length is limited to 256 words, DMA is
performed on two fixed pages, allocated and mapped at driver initialization
time.
Performance figures (in Mbps) on r8a7791/koelsch at different SPI clock
frequencies for 1024-byte and 4096-byte transfers:
1024 bytes 4096 bytes
- 3.25 MHz: PIO 2.1, DMA 2.6 | PIO 2.8, DMA 3.1
- 6.5 MHz: PIO 3.2, DMA 4.4 | PIO 5.0, DMA 5.9
- 13 MHz: PIO 4.2, DMA 6.6 | PIO 8.2, DMA 10.7
- 26 MHz: PIO 5.9, DMA 10.4 | PIO 12.4, DMA 18.4
Note that DMA is only faster than PIO for transfers that exceed the FIFO
size (typically 64 words / 256 bytes).
Also note that large transfers (larger than the group length for DMA, or
larger than the FIFO size for PIO), should use cs-gpio (with the
appropriate pinmux setup), as the hardware chipselect will be deasserted in
between chunks.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixes the following build error introduced by commit b3f6a57506
("spi: omap-uwire: use devm_ functions"):
drivers/spi/spi-omap-uwire.c:465:2: error: implicit declaration of function ‘devm_ioremap’
Since we are including <linux/io.h>, <asm/io.h> is no longer
needed. Remove it.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch removes the chip select function. Chip select should instead be
supported using GPIOs, defining the DT entry "cs-gpios", and letting the SPI
core assert/deassert the chip select as it sees fit.
The chip select control inside the controller is buggy. It is supposed to
automatically assert the chip select based on the activity in the controller,
but it is buggy and doesn't work at all. So instead we elect to use GPIOs.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch introduces the use of devm_clk_get and devm_ioremap instead
of the unmanaged interfaces and removes the corresponding free function
calls.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add trivial runtime PM support. This will only be of benefit on SoCs
where the clock to the SPI interface can be shut down.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
clk_prepare()/clk_enable() can fail, and it's return value should
be checked. Add the proper checking, and while we're here, convert
to clk_prepare_enable().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
- Move buffer pointer and length setup to the top,
- Make unsigned values unsigned,
- Loop over words and increment pointers instead of recalculating them,
which allows to kill bytes_done.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
- Add a timeout when waiting for the transfer complete interrupt,
- If sh_msiof_spi_stop() fails, there's no need to clear IER, as the
interrupt handler has already done that,
- Propagate transfer failures in sh_msiof_transfer_one().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Based on an old patch by Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Let memory subsystem handle the error logging.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Reviewed-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Let memory subsystem do the error logging.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Reviewed-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for v1.1.1 of the SPI QUP controller.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch moves the devm_spi_register_master below the initialization of the
runtime_pm. If done in the wrong order, the spi_register_master fails if any
probed slave devices issue SPI transactions.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Acked-by: Ivan T. Ivanov <iivanov@mm-sol.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It was observed that after module removal followed by insertion,
the SW mode chipselect is not properly set. Thus causing transfer
failure due to incorrect CS toggling.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drop call to platform_set_drvdata() as driver data is not used
anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drop call to platform_set_drvdata() as driver data is not used
anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drop call to platform_set_drvdata() as driver data is not used
anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Drop call to platform_set_drvdata() as driver data is not used
anywhere in the driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is to fix the SPI DMA transfer failure for speed less than 1M.
If using current DMA burst size setting (16), the Rx data bytes are
invalid due to each data byte is multiplied according to the burst
size setting.
Let's said supposedly we shall receive the following 18 bytes of data:
01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18
Instead, the data bytes received consist of "16 bytes of '01' +
2 bytes of '02'" :
01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 01 02 02
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Extract the common parts of rspi_transfer_one(), rspi_rz_transfer_one(),
and qspi_transfer_out_in() into the new function rspi_common_transfer().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Enable DMA support for RSPI on r7s72100 (RZ/A1H).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Enable DMA support for QSPI on R-Car Gen2, for Single, Dual, and Quad SPI
Transfers.
Performance figures for reading from a QSPI FLASH driven at 24.375 MHz
on r8a7791/koelsch:
- Single: 1.1 Mbps PIO, 23 Mbps DMA
- Dual : 12.7 Mbps PIO, 48 Mbps DMA
- Quad : 13 Mbps PIO, 70 Mbps DMA
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
rspi_send_dma() and rspi_send_receive_dma() are very similar. Consolidate
into a single function rspi_dma_transfer(), and add missing checks for
dmaengine_submit() failures.
Both sg_table pointer parameters can be NULL, as RSPI supports TX-only
mode, and unidirectional DMA transfers will also be needed later for
Dual/Quad DMA support.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The DMA routines only need access to the scatter-gather tables inside the
spi_transfer structures, hence just pass those.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Refactor RSPI (on SH) DMA handling to make it reusable for other RSPI
implementations:
- Call the DMA routines after configuring the TX Mode bit and after
calling rspi_receive_init(), so these RSPI-specific operations can be
removed from the DMA routines,
- Absorb rspi_transfer_out_in() into rspi_transfer_one().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the SPI core DMA mapping framework instead of our own.
If available, DMA is used for transfers larger than the FIFO size
(8 or 32 bytes).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SPI DMA core framework needs both RX and TX DMA to function. As a
preparation for converting the driver to use this framework, fall back to
PIO if no DMA channel or only one DMA channel is available.
This affects only RSPI, which could do DMA transfers for TX-only before.
RSPI-RZ and QSPI (at least for Single SPI Transfers) will need both RX and
TX DMA anyway.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The resource is know to exist, as rspi_probe() already mapped it.
Remove the test, and just pass the resource.
Pass the device pointer instead of the platform device pointer, as the
latter is no longer needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Setup of the receive and transmit DMA channels is very similar, so let's
consolidate.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fall back to PIO if DMA configuration failed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The various PIO loops are very similar. Consolidate into a single
function rspi_pio_transfer().
Both buffer pointers can be NULL, as RSPI supports TX-only mode, and
Dual/Quad SPI Transfers are unidirectional.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
RSPI needs dummy transfers to generate the SPI clock on receive.
RSPI-RZ and QSPI always do both transmit and receive.
Use the SPI core SPI_MASTER_MUST_RX/SPI_MASTER_MUST_TX infrastructure
instead of checking for the presence of buffers and providing dummy data
ourselves (for PIO), or providing a dummy buffer (for DMA).
rspi_receive_dma() now provides full duplex DMA transfers on RSPI, and is
renamed to rspi_send_receive_dma().
As the SPI core will always provide a TX buffer, the logic to choose
between DMA send and DMA send/receive in rspi_transfer_one() now has to
check for the presence of an RX buffer. Likewise for the DMA availability
tests in rspi_is_dma().
The buffer tests in qspi_transfer_one() are now always true, so they're
removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The 16-bit DMA support doesn't fit well within the SPI core DMA framework,
as it needs to manage its own double-sized temporary buffers, for handling
the interleaved data.
Remove it, as there is no in-tree board code that sets
rspi_plat_data.dma_width_16bit.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 8449fd76de ("spi: rspi: Merge
rspi_send_pio() and rspi_receive_pio()"), rspi_receive_init() is called
for transmit-only transfers too, while this is not needed.
Only call rspi_receive_init() when receiving, to preserve behavior on
RSPI on SH.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
In commit 7dd6278733 (spi/pxa2xx: Convert
to core runtime PM) master->auto_runtime_pm was set to true.
In this case pm_runtime_enable() must be called *before*
spi_register_master(), otherwise the kernel hangs with this error
message:
spi_master spi0: Failed to power device: -13
A similar fix, but for spi/hspi, was applied in
268d76430d.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Mark Brown <broonie@linaro.org>
By default for every espi transfer, the rx_buf is placed right after the
tx_buf. This can lead to a buffer overflow when the size of both the TX
and RX data cumulated is higher than the allocated 64K buffer for the
transfer (this is the case when sending for instance a read command and
reading 64K back, please see:
http://article.gmane.org/gmane.linux.drivers.mtd/53411 )
This gets fixed by always setting the RX buffer pointer at the begining
of the transfer buffer.
[The driver shouldn't be doing the copy in the first place and instead
sending directly from the supplied buffer but this is at least not worse
than what's there -- broonie]
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Rejecting unsupported values of spi-tx-bus-width and spi-rx-bus-width
may break compatibility with future DTs. Just ignore them, falling back
to Single SPI Transfers.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
The calculation of the bit rate divider used a standard C division, which
rounds down the quotient. This may lead to a higher bitrate than requested.
Round up to avoid this.
E.g. on Koelsch, the SPI flash (configured for 30 MHz) was driven at 48.75
MHz. After this patch it's driven at a safe 24.375 MHz.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
current PIO tranfer method be described as follows:
1. fill as much as bytes but no more than 256 bytes(fifo size)
2. enable oflow/uflow/txfifo_empty interrupt
3. isr process 3 interrupt signal, do complete works.
4. after isr done, if there are left bytes go into 1 else go into 5
5. transfer end
by current PIO transfer method:
1. reduce interrupt counts in spi interrupt line.
2. reduce interrupt latency because no do data fill/fetch in isr.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The spi-topcliff-pch driver is for a companion chip to the Intel Atom
E600 series processors. These are 32-bit x86 processors so the driver
is only needed on X86_32. Add COMPILE_TEST as an alternative, so that
the driver can still be build-tested elsewhere.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch fixes the calculation for determining whether to use FIFO or BLOCK
mode.
Signed-off-by: Andy Gross <agross@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
In case we are doing DMA transfer and the size of the buffer is not multiple
of 4 bytes the driver truncates that to 4-byte boundary and tries to handle
remaining bytes using PIO.
Or that is what it tried to do. What actually happens is that it calls
ALIGN() to the buffer size which aligns it to the next 4-byte boundary
(doesn't truncate). Doing this results 1-3 bytes extra to be transferred.
Furthermore we handle remaining bytes using PIO which results one extra
byte to be transferred. In worst case the driver transfers 4 extra bytes.
While investigating this it turned out that the DMA hardware doesn't even
have such limitation so we can solve this by dropping the code that tries
to handle unaligned bytes.
Reported-by: Chiau Ee Chew <chiau.ee.chew@intel.com>
Reported-by: Hock Leong Kweh <hock.leong.kweh@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The dw_spi_cleanup() function was removed by commit c63f5da008
"spi: dw: Don't call kfree for memory allocated by devm_kzalloc".
commit ec37e8e1f0 "spi: dw: migrate to generic queue infrastructure" added
dw_spi_cleanup() but never use it. So now I got below build warning:
CC [M] drivers/spi/spi-dw.o
drivers/spi/spi-dw.c:609:13: warning: 'dw_spi_cleanup' defined but not used [-Wunused-function]
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make of_device_id array const, because all OF functions
handle it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Found using smatch:
drivers/spi/spi-atmel.c:878 atmel_spi_pump_pio_data() warn: unsigned
'as->current_remaining_bytes' is never less than zero.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
If we fail to create the master queue for some reason we should not attempt
to clean it up since attempting to stop a kthread that was not created will
hang and it's just generally bad practice. Unfortunately at present we call
spi_destroy_queue() even in cases where the creation fails.
Fix this by fixing the error handling in spi_master_initialize_queue() so
that we only flag the master as queued or destroy the queue if creation
succeeded. The change to the flag is done since the general master
cleanup uses this to destroy the queue.
Reported-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
If NO_DMA=y:
drivers/built-in.o: In function `spi_map_buf':
spi.c:(.text+0x21bc60): undefined reference to `dma_map_sg'
drivers/built-in.o: In function `spi_unmap_buf.isra.33':
spi.c:(.text+0x21c32e): undefined reference to `dma_unmap_sg'
make[3]: *** [vmlinux] Error 1
Protect the DMA code by #ifdef CONFIG_HAS_DMA to fix this:
- Extract __spi_map_msg() from spi_map_msg(),
- Provide dummy definitions of __spi_map_msg() and spi_unmap_msg() if
!CONFIG_HAS_DMA.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Also, use this opportunity to let spi_chip_sel() handle chip-select
deactivation as well.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
The availability of SPI Dual or Quad Transfer Mode as indicated by the
"spi-tx-bus-width" and "spi-rx-bus-width" properties in the device tree is
a hardware property of the SPI master, SPI slave, and board wiring. Hence
the SPI core should not reject an SPI slave because an SPI master driver
doesn't (yet) support Dual or Quad Transfer Mode.
Change the lack of Dual or Quad Transfer Mode support in the SPI master
driver from an error condition to a warning condition, and ignore the
unsupported mode bits, falling back to Single Transfer Mode, to avoid
breakages when running old kernels with new device trees.
Fixes: f477b7fb13 (spi: DUAL and QUAD support)
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
Similar to CE4100, BayTrail LPSS SPI can be PCI enumerated
as well. Thus, the functions are renamed from ce4100_xxx
to pxa2xx_spi_pci_xxx to clarify that this is a generic
PCI glue layer. Also, added required infrastructure to
support SPI hosts with different configurations.
This patch is based on Mika Westerberg's previous work.
Signed-off-by: Chew, Chiau Ee <chiau.ee.chew@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
atmel_spi_lock does a spin_lock_irqsave, so we need to renable the
interrupts when we want to schedule.
Signed-off-by: Alexander Stein <alexanders83@web.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Make FSL eSPI CSnBEF and CSnAFT fields in ESPI_SPMODEn registers
(n=0,1,2,3) configurable through device tree.
CSnBEF is the chip select setup time. It's the delay in bits from the
activation of chip select pin to the first clock for data frame.
CSnAFT is the chip select hold time. It's the delay in bits from the
last clock for data frame to the deactivation of chip select pin.
The FSL eSPI driver hardcodes CSnBEF and CSnAFT to 0. Need to set
them to a different value for some device.
Signed-off-by: Jane Wan <Jane.Wan@gainspeed.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
split sirfsoc_spi_transfer function into 3 sub-functions:
spi_sirfsoc_cmd_transfer, spi_sirfsoc_pio_transfer and
spi_sirfsoc_dma_transfer.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add dependency on ARM in Kconfig.
This is to fix the build error related to _relaxed IO.
Remove dependency on SPI_MASTER because this is already defined
under if SPI_MASTER in Kconfig.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Rather than requesting the shyway_clk call clk_get with
the device and a NULL con_id.
This is in keeping with the way that clk_get() is called
on other drivers used by Renesas Gen 1 SoCs. And I believe
it is compatible with supplying clocks via DT, unlike the current code.
It appears to me that the two uses of this driver are
the r8a7778 and r8a7779 SoCs.
The r8a7779 already has clocks setup to allow this driver to continue to work
with this change applied.
The r8a7778 has clocks incorrectly setup to allow this driver to continue
to work with this change applied. This problem is addressed in
"ARM: shmobile: r8a7778: Use clks as MSTP007 parent" which is thus
a pre-requisite of this patch.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@linaro.org>
sometimes t->tx can be equal with t->rx. for example, spidev will make
tx and rx point to spidev->buffer at the same time. currently, for this
case, we map the buffer BIDIRECTION to fix the cache consistency.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
fix a lot of "line over 80 characters" checkpatch issues, on which
the users of the driver, key customers care about this very much.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
orignal GPIO chipslect is not standard because it don't take care to the
chipselect signal: BITBANG_CS_ACTIVE and BITBANG_CS_INACTIVE.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
SPI bitbang supply "chipselect" interface for change chip-select line
, in the SiRFSoC SPI controller, we need to enable "SPI_CS_IO_MODE",
otherwise, spi_sirfsoc_chipselect() has no effect.
now the driver is working is because SPI controller will control CS
automatically without SPI_CS_IO_MODE. this patch makes the CS controller
really controlled by software.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
the old code uses wrong marco - SIRFSOC_SPI_FIFO_FULL is not for
FIFO interrupt status, it is for FIFO status. here in the ISR,
SIRFSOC_SPI_TXFIFO_EMPTY is the right bit for SPI TXFIFO interrupt
status.
Signed-off-by: Qipan Li <Qipan.Li@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add driver for Cadence SPI controller. This is used in Xilinx Zynq.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Spi v3 controller is not only used on Blackfin. So rename it
and use ioread/iowrite api to make it work on other platform.
Signed-off-by: Scott Jiang <scott.jiang.linux@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simplify the cleanup code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
mpc8xxx_spi_probe() has set master->cleanup = mpc8xxx_spi_cleanup,
however current code overrides the setting in fsl_spi_probe() and set
master->cleanup = fsl_spi_cleanup.
Thus the memory allocated for cs is not freed anywhere.
Convert to use devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In current code, master->cleanup and master->setup are not set in the same
function. This makes it hard to read and not good for code maintain.
One example is in fsl-spi.c, master->cleanup is overrided in mpc8xxx_spi_probe()
which leads to a memory leak.
This patch removes mpc8xxx_spi_cleanup() and converts fsl_espi_setup to use
devm_kzalloc so we don't need to take care of freeing memory.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
add optional property devicetree for SPI slave nodes
into devicetree so that LSB mode can be enabled by devicetree.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The existing timeout value in wait_for_completion_timeout is
calculated from the transfer length and speed with tolerance of 10msec.
This is too low because this is used for error conditions such as
hardware hang etc.
The xfer->speed_hz considered may not be the actual speed set
because the best clock divisor is chosen from a limited set such that
the actual speed <= requested speed. This will lead to timeout being
less than actual transfer time.
Considering acceptable latencies, this timeout can be set to a
value double the expected transfer plus 100 msecs.
This patch adds the same in the core.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Don't use unsigned for current_remaining_bytes so we can check
current_remaining_bytes < 0 case.
Use int is enough for current_remaining_bytes.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A few driver specific fixes, the main one being the fix for handling of
complete callbacks that are open coded in individual drivers to allow
callers to omit the completion. As we move things into the core that
sort of issue should become less and less common.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rgeq
-----END PGP SIGNATURE-----
Merge tag 'spi-v3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes, the main one being the fix for handling
of complete callbacks that are open coded in individual drivers to
allow callers to omit the completion. As we move things into the core
that sort of issue should become less and less common"
* tag 'spi-v3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: qup: Depend on ARCH_QCOM
spi: efm32: Update binding document to make "efm32,location" property optional
spi: omap2-mcspi: Convert to use devm_kcalloc
spi: Always check complete callback before calling it
Commit 8fc1b0f87d ("ARM: qcom: Split Qualcomm support into legacy and
multiplatform") removed Kconfig symbol ARCH_MSM_DT. But that commit
left one (optional) dependency on ARCH_MSM_DT untouched.
Three Kconfig symbols used to depend on ARCH_MSM_DT: ARCH_MSM8X60,
ARCH_MSM8960, and ARCH_MSM8974. These three symbols now depend on
ARCH_QCOM. So it appears this driver needs to depend on ARCH_QCOM too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This saves a few unwind code and return proper error if devm_kcalloc fails.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit 1e25cd4729 "spi: Do not require a completion", this checking is
required to prevent NULL pointer dereference.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Pull MIPS updates from Ralf Baechle:
- Support for Imgtec's Aptiv family of MIPS cores.
- Improved detection of BCM47xx configurations.
- Fix hiberation for certain configurations.
- Add support for the Chinese Loongson 3 CPU, a MIPS64 R2 core and
systems.
- Detection and support for the MIPS P5600 core.
- A few more random fixes that didn't make 3.14.
- Support for the EVA Extended Virtual Addressing
- Switch Alchemy to the platform PATA driver
- Complete unification of Alchemy support
- Allow availability of I/O cache coherency to be runtime detected
- Improvments to multiprocessing support for Imgtec platforms
- A few microoptimizations
- Cleanups of FPU support
- Paul Gortmaker's fixes for the init stuff
- Support for seccomp
* 'mips-for-linux-next' of git://git.linux-mips.org/pub/scm/ralf/upstream-sfr: (165 commits)
MIPS: CPC: Use __raw_ memory access functions
MIPS: CM: use __raw_ memory access functions
MIPS: Fix warning when including smp-ops.h with CONFIG_SMP=n
MIPS: Malta: GIC IPIs may be used without MT
MIPS: smp-mt: Use common GIC IPI implementation
MIPS: smp-cmp: Remove incorrect core number probe
MIPS: Fix gigaton of warning building with microMIPS.
MIPS: Fix core number detection for MT cores
MIPS: MT: core_nvpes function to retrieve VPE count
MIPS: Provide empty mips_mt_set_cpuoptions when CONFIG_MIPS_MT=n
MIPS: Lasat: Replace del_timer by del_timer_sync
MIPS: Malta: Setup PM I/O region on boot
MIPS: Loongson: Add a Loongson-3 default config file
MIPS: Loongson 3: Add CPU hotplug support
MIPS: Loongson 3: Add Loongson-3 SMP support
MIPS: Loongson: Add Loongson-3 Kconfig options
MIPS: Loongson: Add swiotlb to support All-Memory DMA
MIPS: Loongson 3: Add serial port support
MIPS: Loongson 3: Add IRQ init and dispatch support
MIPS: Loongson 3: Add HT-linked PCI support
...
The core implementation of cs_change didn't follow the documentation
which says that cs_change in the middle of the transfer means to briefly
deassert chip select, instead it followed buggy drivers which change the
polarity of chip select. Use a delay of 10us between deassert and
reassert simply from pulling numbers out of a hat.
Reported-by: Gerhard Sittig <gsi@denx.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This controller only supports 8-bit word length.
Set bits_per_word_mask so spi core will reject transfers that attempt to use
an unsupported bits_per_word value.
Also remove the duplicate code to test spi->mode, it is done by spi core.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The memory allocated for cs is not freed anywhere.
Convert to use devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With devm_kzalloc, the memory is automatically freed when spi_device detach from
the bus.
Fixes: commit 43f627ac9d (spi: dw: fix memory leak on error path)
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stabe@vger.kernel.org
The memory allocated for chip is not freed anywhere.
Convert to use devm_kzalloc to fix the memory leak.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This fixes the following coccicheck warning:
linux-2.6/drivers/spi/spi-omap-uwire.c:485:2-8: ERROR: missing iounmap; ioremap on line 471 and execution via conditional on line 481
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Andy Shevchenko