Add constants and callback functions for the dwmac on rk3228/rk3229 socs.
As can be seen, the base structure is the same, only registers and the
bits in them moved slightly.
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: Caesar Wang <wxt@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the Qualcomm Technologies, Inc. EMAC gigabit Ethernet
controller.
This driver supports the following features:
1) Checksum offload.
2) Interrupt coalescing support.
3) SGMII phy.
4) phylib interface for external phy
Based on original work by
Niranjana Vishwanathapura <nvishwan@codeaurora.org>
Gilad Avidov <gavidov@codeaurora.org>
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PCI error is detected, in some architectures (like PowerPC) a slot
reset is performed - the driver's error handlers are in charge of "disable"
device before the reset, and re-enable it after a successful slot reset.
There are two cases though that another path is taken on the code: if the
slot reset is not successful or if too many errors already happened in the
specific adapter (meaning that possibly the device is experiencing a HW
failure that slot reset is not able to solve), the core PCI error mechanism
(called EEH in PowerPC) will remove the adapter from the system, since it
will consider this as a permanent failure on device. In this case, a path
is taken that leads to bnx2x_chip_cleanup() calling bnx2x_reset_hw(), which
then tries to perform a HW reset on chip. This reset won't succeed since
the HW is in a fault state, which can be seen by multiple messages on
kernel log like below:
bnx2x: [bnx2x_issue_dmae_with_comp:552(eth1)]DMAE timeout!
bnx2x: [bnx2x_write_dmae:600(eth1)]DMAE returned failure -1
After some time, the PCI error mechanism gives up on waiting the driver's
correct removal procedure and forcibly remove the adapter from the system.
We can see soft lockup while core PCI error mechanism is waiting for driver
to accomplish the right removal process.
This patch adds a verification to avoid a chip reset whenever the function
is in PCI error state - since this case is only reached when we have a
device being removed because of a permanent failure, the HW chip reset is
not expected to work fine neither is necessary.
Also, as a minor improvement in error path, we avoid the MCP information dump
in case of non-recoverable PCI error (when adapter is about to be removed),
since it will certainly fail.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-By: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fdb dumps spanning multiple skb's currently restart from the first
interface again for every skb. This results in unnecessary
iterations on the already visited interfaces and their fdb
entries. In large scale setups, we have seen this to slow
down fdb dumps considerably. On a system with 30k macs we
see fdb dumps spanning across more than 300 skbs.
To fix the problem, this patch replaces the existing single fdb
marker with three markers: netdev hash entries, netdevs and fdb
index to continue where we left off instead of restarting from the
first netdev. This is consistent with link dumps.
In the process of fixing the performance issue, this patch also
re-implements fix done by
commit 472681d57a ("net: ndo_fdb_dump should report -EMSGSIZE to rtnl_fdb_dump")
(with an internal fix from Wilson Kok) in the following ways:
- change ndo_fdb_dump handlers to return error code instead
of the last fdb index
- use cb->args strictly for dump frag markers and not error codes.
This is consistent with other dump functions.
Below results were taken on a system with 1000 netdevs
and 35085 fdb entries:
before patch:
$time bridge fdb show | wc -l
15065
real 1m11.791s
user 0m0.070s
sys 1m8.395s
(existing code does not return all macs)
after patch:
$time bridge fdb show | wc -l
35085
real 0m2.017s
user 0m0.113s
sys 0m1.942s
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Wilson Kok <wkok@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On ThunderX 88xx pass 2.x chips when TSO is offloaded to HW,
HW posts a CQE for every TSO segment transmitted. Current code
does handles this, but is prone to issues when segment sizes are
small resulting in SW processing too many CQEs and also at times
frees a SKB which is not yet transmitted.
This patch handles the errata in a different way and eliminates issues
with earlier approach, TSO packet is submitted to HW with post_cqe=0,
so that no CQE is posted upon completion of transmission of TSO packet
but a additional HDR + IMMEDIATE descriptors are added to SQ due to
which a CQE is posted and will have required info to be used while
cleanup in napi. This way only one CQE is posted for a TSO packet.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a issue in HW where-in while sending GSO sized pkts
as part of TSO, if pkt len falls below configured min packet
size i.e 60, NIC will zero PAD packet and also updates IP total length.
Hence set this value to lessthan min pkt size of MAC + IP + TCP
headers, BGX will anyway do the padding to transmit 64 byte pkt
including FCS.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If DCB is configured on the link partner switch with an
unsupported traffic class configuration (e.g. non-contiguous TCs),
the driver is flagging DCB as disabled. But, for future DCB
LLDPDUs, the driver was checking if the interface was DCB capable
instead of enabled. This was causing a kernel panic when LLDP
was enabled/disabled on the link partner switch.
This patch corrects the situation by having the LLDP event handler
check the correct flag in the pf structure. It also cleans up the
setting and clearing of the enabled flag for other checks.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the sky2 driver to pass number of packets done to NAPI.
The driver was never updated when napi_complete_done was added.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support of Synopsys 3.50a MAC IP in stmmac driver.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stm324xx family chips support Synopsys MAC 3.510 IP.
This patch adds settings for logical glue logic:
-clocks
-mode selection MII or RMII.
Reviewed-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A bugfix for backward compatibility handling introduced undefined
behavior for the case that of_parse_phandle() does not return
a valid entry, as "gcc -Wmaybe-unused" reports:
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c: In function 'xgene_enet_phy_connect':
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c:776:6: error: 'phy_dev' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c: In function 'xgene_enet_mdio_config':
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c:776:6: error: 'phy_dev' may be used uninitialized in this function [-Werror=maybe-uninitialized]
We can work around this by removing the check for zero "np", as
of_phy_connect() will correctly handle a NULL argument so we fall
back into the normal error handling case.
Note that I had previously fixed another bug that resulted in the
exact same warning, but this is a different problem that was
introduced after my original fix.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 03377e381b ("drivers: net: xgene: Fix backward compatibility")
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent commit 087d7a8c91 "tg3: Fix for diasllow rx coalescing
time to be 0" disallow to set Rx coalescing time to be 0 as this stops
generating interrupts for the incoming packets. I found the zero
Tx coalescing time stops generating interrupts for outgoing packets
as well and fires Tx watchdog later. To avoid this, don't allow to set
Tx coalescing time to 0 and also remove subsequent checks that become
senseless.
Cc: satish.baddipadige@broadcom.com
Cc: siva.kallam@broadcom.com
Cc: michael.chan@broadcom.com
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:1230:13-20: WARNING: kzalloc should be used for dcbx_info, instead of kmalloc/memset
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:1192:13-20: WARNING: kzalloc should be used for dcbx_info, instead of kmalloc/memset
Use kzalloc rather than kmalloc followed by memset with 0
This considers some simple cases that are common and easy to validate
Note in particular that there are no ...s in the rule, so all of the
matched code has to be contiguous
Generated by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
CC: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a VLAN is added on a bridge port we should use the existing unicast
flood configuration of the port instead of assuming it's enabled.
Fixes: 0293038e0c ("mlxsw: spectrum: Add support for flood control")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 14d39461b3 ("mlxsw: spectrum: Use per-FID struct for the
VLAN-aware bridge") I added a per-FID struct, which member ports can
take a reference on upon VLAN membership configuration.
However, sometimes only the VLAN flags (e.g. egress untagged) are
toggled without changing the VLAN membership. In these cases we
shouldn't take another reference on the FID.
Fixes: 14d39461b3 ("mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the notifier is registered for every asic instance, however the
same block. Fix this by moving the registration to module init.
Fixes: c723c735fa ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally, I expected that there would be needed to call update
operation in case RALUE record action is changed. However, that is not
needed since write operation takes care of that nicely. Remove prepared
construct and always call the write operation.
Fixes: 61c503f976 ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mlxsw we squash tables 254 and 255 together into HW. Kernel adds/dels
/32 ip to/from both 254 and 255. On del path, that causes the same
prefix being removed twice. Fix this by introducing reference counting
for private mlxsw fib entries. That required a bit of code reshuffle.
Also put dev into fib entry key so the same prefix could be represented
once per every router interface.
Fixes: 61c503f976 ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch takes care of clearing the uninitialized buffer before using it.
1. pfc pri-enable bitmap need to be cleared before setting the requested
enable bits. Without this, the un-touched values will be merged with
requested values and sent to MFW.
2. The data in app-entry field need to be cleared before using it.
3. Clear the output data buffer used in qed_dcbx_query_params().
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Management firmware requires the selection-field (SF) to be set for
configuring the application/protocol entry in IEEE mode. Without this
setting, the app entry will be configured incorrectly in MFW.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dcbx configuration is not supported for VF interfaces. Hence don't populate
the callbacks for VFs and also fail the dcbx-query for VFs.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Return -ENODEV if the MDIO bus is disabled in the device tree.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
a lot of parts in the driver uses devm_* APIs to gain benefits from the
device resource management, so devm_mdiobus_alloc is also used instead
of mdiobus_alloc to have more elegant code flow.
Using common code provided by the devm_* helps to
1) have simplified the code flow as [1] says
2) decrease the risk of incorrect error handling by human
3) only a few drivers used it since it was proposed on linux 3.16,
so just hope to promote for this.
Ref:
[1] https://patchwork.ozlabs.org/patch/344093/
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the missing of_node_put() after finishing the usage
of of_get_child_by_name.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
mtk_stop() must be called to stop for freeing DMA
resources acquired and restoring state changed by mtk_open()
firstly when module removal.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
original mdio_cleanup is not in the symmetric place against where
mdio_init is, so relocate mdio_cleanup to the right one.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
these irqs are not used for shared irq and disabled during ethernet stops.
irq requested by devm_request_irq is safe to be freed automatically on
driver detach.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
use skb_free_frag() instead of legacy put_page()
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
1) If the return value of devm_clk_get is EPROBE_DEFER, we should
defer probing the driver. The change is verified and works based
on 4.8-rc1 staying with the latest clk-next code for MT7623.
2) Changing with the usage of loops to work out if all clocks
required are fine
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
which net device the SKB is complete for depends on the forward port
on txd4 on the corresponding TX descriptor, but the information isn't
set up well in case of SKB fragments that would lead to watchdog timeout
from the upper layer, so fix it up.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Suggested-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Casting away const is bad practice. Since this is ARM specific driver
don't have hardware actually test this.
Having getter functions for ops is really unnecessary code bloat, but
not going to touch that.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add firmware download support for cn23xx device.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support msix interrupt for cn23xx device.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for cn23xx queue manipulation.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support for initializing cn23xx device registers
related to mac, input/output and pf global config.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for cn23xx device init and sriov queue config.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for cn23xx specific queue definitions and
features.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds register definitions and structures for new
device cn23xx.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support of common irq enable functionality for both
iq(instruction queue) and oq(output queue).
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains changes for firmware version management.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate common functionality of various devices
from different files into lio_core.c/octeon_console.c.
Signed-off-by: Derek Chickles <derek.chickles@caviumnetworks.com>
Signed-off-by: Satanand Burla <satananda.burla@caviumnetworks.com>
Signed-off-by: Felix Manlunas <felix.manlunas@caviumnetworks.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check for ethtool_ops structures that are only stored in the ethtool_ops
field of a net_device structure or passed as the second argument to
netdev_set_default_ethtool_ops. These contexts are declared const, so
ethtool_ops structures that have these properties can be declared as const
also.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct ethtool_ops i@p = { ... };
@ok1@
identifier r.i;
struct net_device e;
position p;
@@
e.ethtool_ops = &i@p;
@ok2@
identifier r.i;
expression e;
position p;
@@
netdev_set_default_ethtool_ops(e, &i@p)
@bad@
position p != {r.p,ok1.p,ok2.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct ethtool_ops i = { ... };
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Mark Einon <mark.einon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The addition of the per-queue statistics introduced a harmless warning
on all 32-bit architectures:
drivers/net/ethernet/qlogic/qede/qede_ethtool.c: In function 'qede_get_ethtool_stats':
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:244:31: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
buf[cnt++] = QEDE_TQSTATS_DATA(edev,
^
drivers/net/ethernet/qlogic/qede/qede_ethtool.c:244:22: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
buf[cnt++] = QEDE_TQSTATS_DATA(edev,
^
This changes the cast to 'void *' to shut up the warning, which
avoids the assumptions on the size of the pointer type.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 68db9ec2df ("qede: Add support for per-queue stats.")
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PM_SLEEP is disabled, we get a couple of harmless warnings:
drivers/net/ethernet/renesas/ravb_main.c:2117:12: error: 'ravb_resume' defined but not used [-Werror=unused-function]
drivers/net/ethernet/renesas/ravb_main.c:2104:12: error: 'ravb_suspend' defined but not used [-Werror=unused-function]
The simplest solution here is to replace the #ifdef with __maybe_unused
annotations, which lets the compiler do the right thing by itself.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 0184165b2f ("ravb: add sleep PM suspend/resume support")
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove a useless log message and improve the logic for setting
a PHY address from the contents of the MNG_IF_SEL register.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_warn message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2016-08-29
This series contains updates to fm10k only.
Jake provides all the changes in this series starting with fixes an issue
where VF devices may fail during an unbind/bind and we will never zero
the reference counter for the pci_dev structure. Updated the hot path
to use SW counters instead of checking for hardware Tx pending for
possible transmit hangs, which will improve performance. Fixed the NAPI
budget accounting so that fm10k_poll will return actual work done,
capped at (budget - 1) instead of returning 0. Added a check to ensure
that the device is in the normal IO state before continuing to probe,
which allows us to give a more descriptive message of what is wrong
in the case of uncorrectable AER error. In preparation for adding Geneve
Rx offload support, refactored the current VXLAN offload flow to be a bit
more generic. Added support for receive offloads on one Geneve tunnel.
Ensure that other bits in the RXQCTL register do not get cleared, to
make sure that bits related to queue ownership are maintained. Fixed
an issue in queue ownership assignment which casued a race condition
between the PF and the VF such that potentially a VF could cause FUM
fault errors due to normal PF/VF driver behavior.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PF assigns a new MAC address to a VF it uses the base address
registers to store the MAC address. This allows a VF which loads after
this setup the ability to get the initial address without having to wait
for a mailbox message. Unfortunately to do this, the PF must take queue
ownership away from the VF, which can cause fault errors when there is
already an active VF driver.
This queue ownership assignment causes race condition between the PF and
the VF such that potentially a VF can cause FUM fault errors due to
normal PF/VF driver behavior.
It is not safe to simply allow the PF to write the base address
registers without taking queue ownership back as the PF must also
disable the queues, and this would impact active VF use. The current
code is safe because the queue ownership will prevent the VF from
actually writing but does trigger the FUM fault.
We can do better by simply avoiding the register write process when
a mailbox message suffices. If the message can be sent over the mailbox,
then we will not perform the queue ownership assignment and we won't
update the base address to be the same as the MAC address.
We do still have to write the TXQCTL registers in order to update the
VID of the queue. This is necessary because the TXQCTL register is
read-only from the VF, and thus the VF cannot do this for itself. This
register does not need to wait for the Tx queue to be disabled and is
safe for the PF to write during normal VF operation, so we move this
write to the top of the function above the mailbox message. Without
this, the TXQCTL register would be misconfigured and cause the VF to Tx
hang.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ensure that other bits in the RXQCTL register do not get cleared. This
ensures that bits related to queue ownership are maintained.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Similar to how we handle VXLAN offload, enable support for a single
Geneve tunnel.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In preparation for adding Geneve Rx offload support, refactor the
current VXLAN offload flow to be a bit more generic so that it will be
easier to add the new Geneve code. The fm10k hardware supports one VXLAN
and one Geneve tunnel, so we will eventually treat the VXLAN and Geneve
tunnels identically. To this end, factor out the code that handles the
current list so that we can use the generic flow for both tunnels in the
next patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the event of a surprise remove, we expect the driver to go down,
which includes calling .stop_hw(). However, this function will return an
error because the queues won't appear to cleanly disable. Prevent this
and avoid the unnecessary checks by just returning when
FM10K_REMOVED(hw->hw_addr) is true.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the event of an uncorrectable AER error occurring when the driver has
not loaded, the recovery routines are not done. This is done because
future loads of the driver may not be aware of the IO state and may not
be able to recover at all. In this case, when we next load the driver it
fails due to what appears to be a surprise remove event. Instead, add
a check to ensure that the device is in the normal IO state before
continuing to probe. This allows us to give a more descriptive message
of what is wrong.
Without this change, the driver will attempt to probe up to our first
call of .reset_hw() which will be unable to read registers and act as if
a surprise remove event occurred.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When fm10k_poll fully cleans rings it returns 0. This is incorrect as it
messes up the budget accounting in the core NAPI code. Fix this by
returning actual work done, capped at budget - 1 since the core doesn't
expect a return of the full budget when the driver modifies the NAPI
status.
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: Venkatesh Srinivas <venkateshs@google.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
While technically not needed, as all our uses of ACCESS_ONCE are scalar
types, we already use READ_ONCE in a few places, and for code
readability we can swap all the uses of the older ACCESS_ONCE into
READ_ONCE.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function is only used in fm10k_ethtool.c, so make it static.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous patch added support to check for hardware Tx pending in the
fm10k_down routine. This support was intended to ensure that we
accurately check what the hardware state is. However, checking for Tx
hangs in this manor during the hotpath results in a large performance
hit. Avoid this by making the hotpath check use the SW counters instead.
Fixes: a0f53cf49cb0 ("fm10k: use actual hardware registers when checking for pending Tx", 2016-06-08)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous patch removed the pci_disable_device() call in
.io_error_detected. This call corresponded to a pci_enable_device_mem()
call within .io_slot_reset handler. Change the call here to
a pci_reenable_device() so that it does not increment and leak the
enable_cnt reference count for the device. Without this change, VF
devices may fail during an unbind/bind, and we'll never zero the
reference counter for the pci_dev structure.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Krishneil Singh <Krishneil.k.singh@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The newly added reset logic uses helper functions for the MMIO that
may fail. However, when the read operation fails, we end up writing
back uninitialized data to the register, as gcc warns:
drivers/net/ethernet/apm/xgene/xgene_enet_xgmac.c: In function 'xgene_enet_link_state':
drivers/net/ethernet/apm/xgene/xgene_enet_xgmac.c:213:2: error: 'data' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/net/ethernet/apm/xgene/xgene_enet_xgmac.c:209:6: note: 'data' was declared here
u32 data;
We already print a warning to the console log if that happens,
the best alternative that I can see is skip the rest of the reset
sequence if the register value cannot be read: Most likely the
write would fail as well, and if it succeeded, worse things could
happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 3eb7cb9dc9 ("drivers: net: xgene: XFI PCS reset when link is down")
Cc: Fushen Chen <fchen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After resume from hibernate on arm64, any amd-xgbe devices that were
running when we hibernated are reported as down, even when it is not.
Re-plugging the cables does not cause the interface to come back, the
link must be marked as down then up via 'ip set link' using the serial
console.
This happens because the device has been power-cycled and possibly
re-initialised by firmware, whereas the driver's memory structures have
been restored from the hibernate image and the two do not agree.
Schedule a restart of the device after powerup in case the world changed
while we were asleep.
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b70661c708 ("net: smc91x: use run-time configuration on all ARM
machines") broke some ARM platforms through several mistakes. Firstly,
the access size must correspond to the following rule:
(a) at least one of 16-bit or 8-bit access size must be supported
(b) 32-bit accesses are optional, and may be enabled in addition to
the above.
Secondly, it provides no emulation of 16-bit accesses, instead blindly
making 16-bit accesses even when the platform specifies that only 8-bit
is supported.
Reorganise smc91x.h so we can make use of the existing 16-bit access
emulation already provided - if 16-bit accesses are supported, use
16-bit accesses directly, otherwise if 8-bit accesses are supported,
use the provided 16-bit access emulation. If neither, BUG(). This
exactly reflects the driver behaviour prior to the commit being fixed.
Since the conversion incorrectly cut down the available access sizes on
several platforms, we also need to go through every platform and fix up
the overly-restrictive access size: Arnd assumed that if a platform can
perform 32-bit, 16-bit and 8-bit accesses, then only a 32-bit access
size needed to be specified - not so, all available access sizes must
be specified.
This likely fixes some performance regressions in doing this: if a
platform does not support 8-bit accesses, 8-bit accesses have been
emulated by performing a 16-bit read-modify-write access.
Tested on the Intel Assabet/Neponset platform, which supports only 8-bit
accesses, which was broken by the original commit.
Fixes: b70661c708 ("net: smc91x: use run-time configuration on all ARM machines")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_warn message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in dev_warn message.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtool has 11 flow tables, each flow table has its own priority.
Increase the number of priorities to be aligned with the number of flow
tables.
Fixes: 1174fce8d1 ('net/mlx5e: Support l3/l4 flow type specs in ethtool flow steering')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon set ETS failure due to user invalid input, add error prints to
specify the exact error to the user.
Fixes: cdcf11212b ('net/mlx5e: Validate BW weight values of ETS')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Free 'in' command object also when mlx5_core_modify_tir fails.
Fixes: 724b2aa151 ("net/mlx5e: TIRs management refactoring")
Signed-off-by: Kamal Heib <kamalh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a counter in ethtool for the number of times that
TX xmit_more was used.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver RQ has two possible configurations: striding RQ and
non-striding RQ. Until this patch, the driver always reported the
number of hardware WQEs (ring descriptors). For non striding RQ
configuration, this was OK since we have one WQE per pending packet
For striding RQ, multiple packets can fit into one WQE. For better
user experience we normalize the rx_pending parameter (size of wqe/mtu)
as the average ring size in case of striding RQ.
Fixes: 461017cb00 ('net/mlx5e: Support RX multi-packet WQE ...')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of asking the firmware to flush the SQ (Send Queue) via
asynchronous completions when moved to error, we handle SQ flush
manually (mlx5e_free_tx_descs) same as we did when SQ flush got
timed out or on tx_timeout.
This will reduce SQs flush time and speedup interface down procedure.
Moved mlx5e_free_tx_descs to the end of en_tx.c for tx
critical code locality.
Fixes: 29429f3300 ('net/mlx5e: Timeout if SQ doesn't flush during close')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ICO (Internal control operations) SQ (Send Queue) is closed/disabled
after RQ (Receive Queue). After RQ is closed an ICO SQ completion
might post a fragmented MPWQE (Multi Packet Work Queue Element) into
that RQ.
As on regular RQ post, check if we are allowed to post to that
RQ (RQ is enabled). Cleanup in-progress UMR MPWQE on mlx5e_free_rx_descs
if needed.
Fixes: bc77b240b3 ('net/mlx5e: Add fragmented memory support for RX multi packet WQE')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will significantly reduce receive queue flush time on interface
down.
Instead of asking the firmware to flush the RQ (Receive Queue) via
asynchronous completions when moved to error, we handle RQ flush
manually (mlx5e_free_rx_descs) same as we did when RQ flush got timed
out.
This will reduce RQs flush time and speedup interface down procedure
(ifconfig down) from 6 sec to 0.3 sec on a 48 cores system.
Moved mlx5e_free_rx_descs en_main.c where it is needed, to keep en_rx.c
free form non critical data path code for better code locality.
Fixes: 6cd392a082 ('net/mlx5e: Handle RQ flush in error cases')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ConnectX-4 UMR (User Memory Region) MTT translation table offset in WQE
is limited to U16_MAX, before this patch we ignored that limitation and
requested the maximum possible UMR translation length that the netdev
might need (MAX channels * MAX pages per channel).
In case of a system with #cores > 32 and when linear WQE allocation fails,
falling back to using UMR WQEs will cause the RQ (Receive Queue) to get
stuck.
Here we limit UMR length to min(U16_MAX, max required pages) (while
considering the required alignments) on driver load, by default U16_MAX is
sufficient since the default RX rings value guarantees that we are in
range, dynamically (on set_ringparam/set_channels) we will check if the
new required UMR length (num mtts) is still in range, if not, fail the
request.
Fixes: bc77b240b3 ('net/mlx5e: Add fragmented memory support for RX multi packet WQE')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the cpsw_fill_rx_channels()
error handling case instead of 0, as done elsewhere in this function.
Fixes: ce52c74457 ("net: ethernet: ti: cpsw: add ethtool channels support")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MC_CMD_TRIGGER_INTERRUPT does not work on the SFC9140, as used in the
sfn7x42q and sfn7x24f.
Check for this using the MCDI workaround mechanism.
The command is only used during self test. If it's not supported, skip
the interrupt test.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nic_data was already initialised to the right thing, no need to assign
it again.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX size bins were not supported on the 7000's 40G MAC, but the 8000 series
does support them and the MCPU advertises that via a new capability bit.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 32-bit systems, mask is only an array of 3 longs, not 4, so don't try
to write to mask[3].
Also include build-time checks in case the size of the bitmask changes.
Fixes: 3c36a2aded ("sfc: display vadaptor statistics for all interfaces")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add tso/tso6 support to the alx driver.
Based on information from the downstream driver at github.com/qca/alx
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because we change to use the PDMA as the Ethernet RX DMA engine,
the patch modifies to set GDM to send packets to PDMA for RX.
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because the PDMA has richer features than the QDMA for Ethernet RX
(such as multiple RX rings, HW LRO, etc.),
the patch modifies to use the PDMA to handle Ethernet RX.
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Nelson Chang <nelson.chang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of trapping certain packets to the CPU and then relying on it to
flood them we can instead make the device mirror them.
The following packet types are mirrored:
* DHCP: Broadcast packets that should be flooded by the device, but also
trapped in case CPU is running the DHCP server.
* IGMP query: Multicast packets that need to be forwarded to other
bridge ports, but also trapped so that receiving netdev will be marked
as a router port by the bridge driver.
* ARP request: Broadcast packets that should be forwarded to other
bridge ports, but also trapped in case requested IP is of the local
machine.
* ARP response: Unicast packets that should be forwarded by the bridge
but also trapped in case response is directed at us.
Set the trap action of such packets to mirror and mark them using
'offload_fwd_mark' to prevent the bridge driver from forwarding them
itself.
Note that OSPF packets are also marked despite their action being trap.
The reason for this is that the device traps such packets in the
pipeline after they were already flooded.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we only trapped packets to CPU, but we are going to allow
some packets to be mirrored (trap & forward) to CPU.
Extend the Rx listener with 'action' member.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of copying & pasting the same struct initialization for every
Rx listener, just use a macro.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
switchdev_port_fwd_mark_set() is used to set the 'offload_fwd_mark' of
port netdevs so that packets being flooded by the device won't be
flooded twice.
It works by assigning a unique identifier (the ifindex of the first
bridge port) to bridge ports sharing the same parent ID. This prevents
packets from being flooded twice by the same switch, but will flood
packets through bridge ports belonging to a different switch.
This method is problematic when stacked devices are taken into account,
such as VLANs. In such cases, a physical port netdev can have upper
devices being members in two different bridges, thus requiring two
different 'offload_fwd_mark's to be configured on the port netdev, which
is impossible.
The main problem is that packet and netdev marking is performed at the
physical netdev level, whereas flooding occurs between bridge ports,
which are not necessarily port netdevs.
Instead, packet and netdev marking should really be done in the bridge
driver with the switch driver only telling it which packets it already
forwarded. The bridge driver will mark such packets using the mark
assigned to the ingress bridge port and will prevent the packet from
being forwarded through any bridge port sharing the same mark (i.e.
having the same parent ID).
Remove the current switchdev 'offload_fwd_mark' implementation and
instead implement the proposed method. In addition, make rocker - the
sole user of the mark - use the proposed method.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ppe_cb->ppe_common_cb is being dereferenced before a null check is
being made on it. If ppe_cb->ppe_common_cb is null then we end up
with a null pointer dereference when assigning dsaf_dev. Fix this
by moving the initialisation of dsaf_dev once we know
ppe_cb->ppe_common_cb is OK to dereference.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When cp_rx_poll does not get enough packet, it will check the rx
interrupt status again. If so, it will jumpt to rx_status_loop again.
But the goto jump resets the rx variable as zero too.
As a result, it causes one possible deadloop. Assume this case,
rx_status_loop only gets the packet count which is less than budget,
and (cpr16(IntrStatus) & cp_rx_intr_mask) condition is always true.
It causes the deadloop happens and system is blocked.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes a common flow for Client instance open during init
and reset path. The Client subtask can handle both the cases instead of
making a separate notify_client_of_open call.
Also it may fix a bug during reset where the service task was leaking
some memory and causing issues.
Change-Id: I7232a32fd52b82e863abb54266fa83122f80a0cd
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we keep shadow copies of which interrupt sources are enabled
through the intrl2_*_mask_{set,clear} macros, make sure that the
ordering in which we do these two operations: update the copy, then
unmask the register is correct.
This is not currently a problem because we actually do not use them, but
we will in a subsequent patch optimizing register accesses, so better be
safe here.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -ENOMEM from the dma_map_single error
handling case instead of 0, as done elsewhere in this function.
Fixes: 032c5e8284 ("Driver for IBM System i/p VNIC protocol")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove an open coded simple_open() function and replace file
operations references to the function with simple_open()
instead.
Generated by: scripts/coccinelle/api/simple_open.cocci
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Hip06 SoC, the RoCE Engine is part of the Hisilicon Network
Subsystem and is dependent upon DSAF module. Therefore, certain
functions like RESET are exposed through the common registers of
HNS DSAF module which are memory-mapped by the HNS driver and
currently can only be accessed through DT/syscon interface.
This patch adds the support of ACPI to the existing RoCE reset
function in the HNS driver(please refer NOTE 2). Hisilicon RoCE
driver (please refer NOTE 1) shall call this reset function during
probe time to reset the RoCE Engine.
The HNS Reset function indirectly ends up in calling the _DSM()
function part of the DSDT ACPI Table. Actual reset functionality
for ACPI is implemented within the ACPI DSDT Table which also has
been enhanced to support this change.
Support of ACPI in the HNS RoCE driver shall be pushed through a
different accompanying below patch:
"IB/hns: Add support of ACPI to the Hisilicon RoCE Driver"
NOTE 1: HNS RoCE driver has already been accepted by its maintainer
Doug Ledford<dledford@redhat.com>. Please refer below link:
https://www.spinics.net/lists/linux-rdma/msg38850.html
NOTE 2: RoCE reset function patch has been accepted and now is
part of the net-next:
https://www.mail-archive.com/netdev@vger.kernel.org/msg123867.html
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
* net/mlx5: Add sniffer namespaces
* net/mlx5: Introduce sniffer steering hardware capabilities
* net/mlx5: Configure IB devices according to LAG state
* net/mlx5: Vport LAG creation support
* net/mlx5: Add LAG flow steering namespace
* net/mlx5: LAG demux flow table support
* net/mlx5: LAG and SRIOV cannot be used together
* net/mlx5e: Avoid port remapping of mlx5e netdev TISes
* net/mlx5: Get RoCE netdev
* net/mlx5: Implement RoCE LAG feature
* net/mlx5: Add HW interfaces used by LAG
* net/mlx5: Separate query_port_proto_oper for IB and EN
* net/mlx5: Expose mlx5e_link_mode
* net/mlx5: Update struct mlx5_ifc_xrqc_bits
* net/mlx5: Modify RQ bitmask from mlx5 ifc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXu20hAAoJEORje4g2cliniO8P/0nMxLemOxY63u7P6DqT+UZQ
+LN62W+/iLicNayKkt8mtcjnDm768YcF3ADvx73vRvKEeUyyEqT5ChMA59eicf70
rrumfNXB/kfBOaPh5rFWf4Tn8WWpKW+0559drm80NslFZF9jjF9pwv5QGg7xISb7
fYLcDQWn+5fYDuZzYsSu8zZKUEyGN0AugdjfxT5OHfh4rw+6oqGDb2fhH6LdkD8q
j3Qx1cPmdQQnjJ5veXJFJT5qHFDqJlNmy85s4l99ItdWD/bcU29ue3Q3vNf7+lHp
XoJB4ZRWG7sf98yXYXnOUt3iGUMdSJzpLfZqh/Nx9U1LZpdJ8lmBf7pRuR1hpPIN
yDitcz+CMcFVr2WxvwWaUPhRE7SJsZxxr6tQISgRicYcFVyy9e7mLjABMtkh9vEn
CXXqiDGUb/27HqTi9ha5qRiLoeT8yFpOCkINL4omV2FJKoUEbC+Jbq5P0mjnPpS1
ZdzTOzWCtkDQGtLbi+nCIF5SVTv7CCDU+6VpGZPmk6M4/ednwajhxGPsbw6bRpna
ck5SglGO8dFAaUv1UVRq04PIt7Lj2FRakP7sHWx3tc9XEP8syLX0OEiVB+ZN3yRn
y2TlpsREk7AqDdRulwM4qfuNd4AxaDklXyS3C79RiJtenYO4GUGrJ6J6ryesLg8u
tGKVV3fXEr2Hve6cTkpu
=+m21
-----END PGP SIGNATURE-----
Merge tag 'shared-for-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leon/linux-rdma into mlx5-shared
Mellanox ConnectX-4/Connect-IB shared code (SW part)
* net/mlx5: Add sniffer namespaces
* net/mlx5: Introduce sniffer steering hardware capabilities
* net/mlx5: Configure IB devices according to LAG state
* net/mlx5: Vport LAG creation support
* net/mlx5: Add LAG flow steering namespace
* net/mlx5: LAG demux flow table support
* net/mlx5: LAG and SRIOV cannot be used together
* net/mlx5e: Avoid port remapping of mlx5e netdev TISes
* net/mlx5: Get RoCE netdev
* net/mlx5: Implement RoCE LAG feature
* net/mlx5: Add HW interfaces used by LAG
* net/mlx5: Separate query_port_proto_oper for IB and EN
* net/mlx5: Expose mlx5e_link_mode
* net/mlx5: Update struct mlx5_ifc_xrqc_bits
* net/mlx5: Modify RQ bitmask from mlx5 ifc
When ndo_set_rx_mode() is called for bnx2x, as part of process of
configuring the new MAC address filters [both unicast & multicast]
driver begins by flushing the existing configuration and then iterating
over the network device's list of addresses and configures those instead.
This has the side-effect of creating a short gap where traffic wouldn't
be properly classified, as no filters are configured in HW.
While for unicasts this is rather insignificant [as unicast MACs don't
frequently change while interface is actually running],
for multicast traffic it does pose an issue as there are multicast-based
networks where new multicast groups would constantly be removed and
added.
This patch tries to remedy this [at least for the newer adapters] -
Instead of flushing & reconfiguring all existing multicast filters,
the driver would instead create the approximate hash match that would
result from the required filters. It would then compare it against the
currently configured approximate hash match, and only add and remove the
delta between those.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before commit 99724c18fc ("mlxsw: spectrum: Introduce support for
router interfaces") we used to assign vFIDs to the created vPorts. Since
these vPorts were used for slow path traffic we had to disable learning
for them, as it doesn't make sense to have it enabled.
This is no longer the case and now vPorts are either used for router
interfaces (for which learning is disabled by the firmware) or bridge
ports (for which learning is explicitly enabled by the driver).
Therefore, we can remove the learning configuration upon vPort creation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We now offload the learning configuration to the device and don't rely
on the driver to decide whether to learn the FDB record, so remove the
check.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now we simply stored the learning configuration of a bridge
port in the driver and decided whether to learn a new FDB record based
on this value.
However, this is sub-optimal in cases where learning is disabled on the
bridge port, as the device repeatedly generates learning notifications
for the same record.
Instead, offload the learning configuration to the device, thereby
preventing it from generating notifications when learning is disabled.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to prevent the device from generating learning
notifications for a port that was configured with learning disabled.
Since learning configuration is done per {Port, VID} we need to apply
the port's learning configuration for any VID that is added to the
bridge port's VLAN filter list.
When a VID is added to the VLAN filter list of a VLAN-aware bridge port,
configure the {Port, VID} learning status according to the port's
configuration. When the VID is removed, disable learning for the {Port,
VID}.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing VLANs from the VLAN-aware bridge we shouldn't abort on the
first error, as we'll otherwise have resources that will never be freed.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 05978481e7 ("mlxsw: spectrum: Create PVID vPort before
registering netdevice") removed __mlxsw_sp_port_vlans_del() from the
init sequence of the driver, which forced it to be non-symmetric with
regards to __mlxsw_sp_port_vlans_add().
Make both functions symmetric as the constraint no longer exists.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Up until now a learning session ended whenever the number of queried
records was zero. This turned out to be problematic in situations where
a large number of MACs (48K) had to be processed by the switch driver,
as RTNL mutex is held during the learning session.
Instead, limit the number of FDB records that can be processed in a
session to 64. This means that every time the device is queried for
learning notifications (currently, every 100ms), up to 64 records will
be processed by the switch driver.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the function mlxsw_router_neigh_construct search the rif according
to the neighbour dev other than the dev that was passed to the ndo, thus
allowing creating neigbhours upon stacked devices.
Fixes: 6cf3c971dc ("mlxsw: spectrum_router: Add private neigh table")
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case we have a layer 3 interface on top of a bridge (VLAN / FID RIF),
then we should flood the following packet types to the router:
* Broadcast: If DIP is the broadcast address of the interface, then we
need to be able to get it to CPU by trapping it following route lookup.
* Reserved IP multicast (224.0.0.X): Some control packets (e.g. OSPF)
use this range and are trapped in the router block.
Fixes: 99f44bb352 ("mlxsw: spectrum: Enable L3 interfaces on top of bridge devices")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx5: Add sniffer namespaces
* net/mlx5: Introduce sniffer steering hardware capabilities
* net/mlx5: Configure IB devices according to LAG state
* net/mlx5: Vport LAG creation support
* net/mlx5: Add LAG flow steering namespace
* net/mlx5: LAG demux flow table support
* net/mlx5: LAG and SRIOV cannot be used together
* net/mlx5e: Avoid port remapping of mlx5e netdev TISes
* net/mlx5: Get RoCE netdev
* net/mlx5: Implement RoCE LAG feature
* net/mlx5: Add HW interfaces used by LAG
* net/mlx5: Separate query_port_proto_oper for IB and EN
* net/mlx5: Expose mlx5e_link_mode
* net/mlx5: Update struct mlx5_ifc_xrqc_bits
* net/mlx5: Modify RQ bitmask from mlx5 ifc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJXu20hAAoJEORje4g2cliniO8P/0nMxLemOxY63u7P6DqT+UZQ
+LN62W+/iLicNayKkt8mtcjnDm768YcF3ADvx73vRvKEeUyyEqT5ChMA59eicf70
rrumfNXB/kfBOaPh5rFWf4Tn8WWpKW+0559drm80NslFZF9jjF9pwv5QGg7xISb7
fYLcDQWn+5fYDuZzYsSu8zZKUEyGN0AugdjfxT5OHfh4rw+6oqGDb2fhH6LdkD8q
j3Qx1cPmdQQnjJ5veXJFJT5qHFDqJlNmy85s4l99ItdWD/bcU29ue3Q3vNf7+lHp
XoJB4ZRWG7sf98yXYXnOUt3iGUMdSJzpLfZqh/Nx9U1LZpdJ8lmBf7pRuR1hpPIN
yDitcz+CMcFVr2WxvwWaUPhRE7SJsZxxr6tQISgRicYcFVyy9e7mLjABMtkh9vEn
CXXqiDGUb/27HqTi9ha5qRiLoeT8yFpOCkINL4omV2FJKoUEbC+Jbq5P0mjnPpS1
ZdzTOzWCtkDQGtLbi+nCIF5SVTv7CCDU+6VpGZPmk6M4/ednwajhxGPsbw6bRpna
ck5SglGO8dFAaUv1UVRq04PIt7Lj2FRakP7sHWx3tc9XEP8syLX0OEiVB+ZN3yRn
y2TlpsREk7AqDdRulwM4qfuNd4AxaDklXyS3C79RiJtenYO4GUGrJ6J6ryesLg8u
tGKVV3fXEr2Hve6cTkpu
=+m21
-----END PGP SIGNATURE-----
Merge tag 'shared-for-4.9-2' of git://git.kernel.org/pub/scm/linux/kernel/git/leon/linux-rdma
Saeed Mahameed says:
====================
Mellanox mlx5 core driver updates 2016-08-24
This series contains some low level and API updates for mlx5 core
driver interface and mlx5_ifc.h, plus mlx5 LAG core driver support,
to be shared as base code for net-next and rdma mlx5 4.9 submissions.
From Alex and Artemy, Update mlx5_ifc for modify RQ and XRC bits.
From Noa, Expose mlx5 link modes so they can be used in RDMA tree for rdma tools.
From Aviv, LAG support needed for RDMA.
- Add needed hardware structures, layouts and interface
- mlx5 core driver LAG implementation
- Introduce mlx5 core driver LAG API for mlx5_ib
From Maor, add two low level patches for mlx5 hardware sniffer QP
infrastructure bits and capabilities, plus added the namespace for sniffer
steering tables. Needed for RDMA subtree.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the return type of ena_set_push_mode() to be void,
as it always returns 0.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add provision for configuring the fastpath queues with Tx (or Rx) only
functionality.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently enable interrupts before we enable NAPI. If an RX interrupt
hits before we enabled NAPI then the NAPI callback is never called and
we leave the hardware with RX interrupts disabled, which of course leads
us to never handling received packets. Fix this by moving the interrupt
enable to after we've enable NAPI and the reclaim tasklet.
Fixes: cd5e412347 ("dwc_eth_qos: do phy_start before resetting hardware")
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_prepare_enable() may fail, so we should better check its return
value and propagate it in the case of failure
While at it, replace __lpc_eth_clock_enable() with a plain
clk_prepare_enable/clk_disable_unprepare() call in order to
simplify the code.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we disable SRIOV, we used to unregister the netdev but wasn't
freed. But next time when the same netdev is registered, since the state
was in 'NETREG_UNREGISTERED', we used to hit BUG_ON in register_netdevice,
where it expects the state to be 'NETREG_UNINITIALIZED'.
Alloc netdev and register them while configuring SRIOV, and free them
when SRIOV is disabled. Also added a new function to setup ethernet
properties instead of using ether_setup. Set carrier off by default,
since we don't have to do any transmit on the interface.
Fixes: 7829451c69 ("cxgb4: Add control net_device for configuring PCIe VF")
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
liquidio_set_rxcsum_command is a local function only, no need to expose
it outside of lio_main.c so declare it static and make sparse happy.
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current scatter-gather logic in gianfar is flawed, since
it does not consider the eTSEC's RxBD 'Data Length' field is
context depening: for the last fragment it contains the full
frame size, while fragments contain the fragment size, which
equals the value written to register MRBLR.
This causes data corruption as soon as the hardware starts
to fragment receiving frames. As a result, the size of
fragmented frames is increased by
(nr_frags - 1) * MRBLR
We first noticed this issue working with DSA, where an ICMP
request sized 1472 bytes causes the scatter-gather logic to
kick in. The full Ethernet frame (1518) gets increased by
DSA (4), GMAC_FCB_LEN (8), and FSL_GIANFAR_DEV_HAS_TIMER
(priv->padding=8) to a total of 1538 octets, which is
fragmented by the hardware and reconstructed by the driver
to a 3074 octet frame.
This patch fixes the problem by adjusting the size of
the last fragment.
It was tested by setting MRBLR to different multiples of
64, proving correct scatter-gather operation on frames
with up to 9000 octets in size.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The eTSEC register MRBLR defines the maximum space in
the RX buffers and is set to 1536 by gianfar. This
reasonably covers the common use case where the MTU
is kept at default 1500. In that case, the largest
Ethernet frame size of 1518 plus an optional
GMAC_FCB_LEN of 8, and an additional padding of 8
to handle FSL_GIANFAR_DEV_HAS_TIMER totals to 1534
and nicely fit within the chosen MRBLR.
Alas, if the eTSEC is attached to a DSA enabled switch,
the (E)DSA header extension (4 or 8 bytes) causes every
maximum sized frame to be fragmented by the hardware.
This patch increases the maximum RX buffer size by 8
and rounds up to the next multiple of 64, which the
hardware's defines as RX buffer granularity.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* net/mlx5: Introduce alloc_encap and dealloc_encap commands
* net/mlx5: Update mlx5_ifc.h for vxlan encap/decap
* net/mlx5: Enable setting minimum inline header mode for VFs
* net/mlx5: Improve driver log messages
* net/mlx5: Unify and improve command interface
* {net,IB}/mlx5: Modify QP commands via mlx5 ifc
* {net,IB}/mlx5: QP/XRCD commands via mlx5 ifc
* {net,IB}/mlx5: MKey/PSV commands via mlx5 ifc
* {net,IB}/mlx5: CQ commands via mlx5 ifc
* net/mlx5: EQ commands via mlx5 ifc
* net/mlx5: Pages management commands via mlx5 ifc
* net/mlx5: MCG commands via mlx5 ifc
* net/mlx5: PD and UAR commands via mlx5 ifc
* net/mlx5: Access register and MAD IFC commands via mlx5 ifc
* net/mlx5: Init/Teardown hca commands via mlx5 ifc
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QIAc
-----END PGP SIGNATURE-----
Merge tag 'shared-for-4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/leon/linux-rdma
Saeed Mahameed says:
====================
Mellanox mlx5 core driver updates 2016-08-20
This series contains several low level and API updates for mlx5 core
commands interface and mlx5_ifc.h to be shared as base code for net-next and
rdma mlx5 4.9 submissions.
From Saeed, ten patches that refactors old layouts of firmware commands which
were manually generated before we introduced the mlx5_ifc, now all of the firmware
commands inbox/outbox layouts moved to use mlx5_ifc and we remove the old
manually generated structures. Plus to those ten patches, we add two patches
that unifies mlx5 commands execution interface and improve the driver log messages
in that area.
From Hadar and Ilya, added the needed hardware bits and infrastructure for
minimum inline headers setting and encap/decap commands and capabilities,
needed for E-Switch offloads.
This series applies on top latest net-next and rdma/master, and smoothly merges with
the latest "Mellanox 100G mlx5 fixes 2016-08-16" series already applied into net branch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
These ops allow to control number of channels driver is allowed to
work with at cpdma level. The maximum number of channels is 8 for
rx and 8 for tx. In dual_emac mode the h/w channels are shared
between two interfaces and changing number on one interface changes
number of channels on another.
How many channels are supported and enabled:
$ ethtool -l ethX
Change number of channels (up to 8)
$ ethtool -L ethX rx 6 tx 6
Per-channel statistic:
$ ethtool -S ethX
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep the driver internals in C file. Currently it's not required for
drivers to know rx or tx a channel is, except create function.
So correct "channel create" function, and use all channel struct
macroses only for internal use.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw h/w supports up to 8 tx and 8 rx channels. This patch adds
multi-queue support to the driver only, shaper configuration will
be added with separate patch series. Default shaper mode, as
before, priority mode, but with corrected priority order, 0 - is
highest priority, 7 - lowest.
The poll function handles all unprocessed channels, till all of
them are free, beginning from hi priority channel.
In dual_emac mode the channels are shared between two network devices,
as it's with single-queue default mode.
The statistic for every channel can be read with:
$ ethtool -S ethX
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupts shouldn't be disabled while receiving skb, but while
ctrl_stop, the channels are stopped and all remaining packets are
handled with netif_receive_skb(), it can cause WARN_ONCE when ctrl
is stopping while not all packets were handled with NAPIs:
lock_irq_save
cpdma_ctlr_stop
cpdma_chan_top
__cpdma_chan_free
cpsw_rx_handler
netif_receive_skb
So, split locking while ctrl stop thus interrupts are still
enabled while skbs handling. It can cause WARN_ONCE in rare
cases when ctrl is stopping while not all packets were handled
with NAPIs.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx channels share same pool of descriptors. Thus one channel can
block another if pool is emptied by one. But, the shaper should
decide which channel is allowed to send packets. To avoid such
impact of one channel on another, let every channel to have its
own piece of pool.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement set_tx_maxrate NDO to perform per queue tx rate limiting.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to bind/unbind specified tx queues to/from scheduling
classes. If a queue is already bound to a scheduling class, it is
unbound first and then bound to a new specified class.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to create tx traffic scheduling classes with specified
scheduling parameters. Return an existing class if a match is found
with same scheduling parameters.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each VF employees a lock that's supposed to serialize its usage of the
HW channel for communication with its PF, but the critical section is
ill-defined:
- VFs currently release the lock whenever the PF response arrives,
prior to actually processing the reply buffer [which was also supposed
to have been protected by same lock].
- The lock would be released on first response, ignoring the possibilty
the sw flow isn't over [as might be the case of the acquisition flow].
As a result, the flow would run unprotected and would cause a double
mutex release [as the additional message completion would release it
while its actually already free].
Change the flow to have a dedicated function to be called at end of each
flow and release the lock.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Modern VFs can't run on old non-compatible as the fastpath HSI is
slightly changed - but as the HSI is actually very close [basically,
a single bit whose meaning flipped] this can be supported with small
modifications.
The major differences would be in:
- Recognizing that VF is running on top of a legacy PF.
- Returning some slowpath configurations that are no longer needed
on top of modern PFs, but would be required when working over
the legacy ones.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware would silently drop any control frame sent by VF to prevent
a malicious VF from generating pause flood in the network.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8.10.x FW added support for forward compatability as well as
'future' backward compatibility, but only to those VFs that were
using HSI which was 8.10.x based or newer.
The latest firmware now supports backward compatibility for the
older VFs based on 8.7.x and 8.8.x firmware as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver never bothered marking the VF's vport with the VF's sw_fid.
As a result, FLR flows are not going to clean those vports.
If the vport was active when FLRed, re-activating it would lead
to a FW assertion.
Fixes: dacd88d6f6 ("qed: IOV l2 functionality")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Reuse existing functionality from memdup_user() instead of keeping
duplicate source code.
This issue was detected by using the Coccinelle software.
* Return directly if this copy operation failed.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy_dev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the address configured in the device tree is invalid, the
driver will fallback to using a random address from the locally
administered range.
Signed-off-by: Daniel Romell <daro@hms.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for the new copper device X557.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This shouldn't matter as nothing should be attached still to be
consisted control MDIO speed for these devices as well.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The X557 devices use a different interface to the LED for the port.
This patch reflect that change.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add geneve Rx offload support for x550em_a.
The implementation follows the vxlan code with the lower 16 bits of
the VXLANCTRL register holding the UDP port for VXLAN and the upper
for Geneve.
Disabled NFS filters in the RFCTL register which allows us to simplify
the check for VXLAN and Geneve packets in ixgbe_rx_checksum().
Removed vxlan from the name of the callback functions and replaced it
with udp_tunnel which is more in line with the new API.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF driver was only receiving the first 4 bytes of the MAC due
to an incorrect size parameter for ixgbevf_write_msg_read_ack()
in ixgbevf_set_rar_vf().
Correct the size by calculating it on a fly for all instances where
we call ixgbevf_write_msg_read_ack()
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ethtool reports backplane type interfaces as 1000/10000baseT link modes.
This has been corrected to report the media as KR, KX or KX4 based on the backplane interface present.
Signed-off-by: Veola Nazareth <veola.nazareth@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The RAR entry for the SAN MAC address was being cleared when we were
clearing the VMDq pool bits. In order to prevent this we need to add
an extra check to protect the SAN MAC from being cleared.
Fixes: 6e982aeae ("ixgbe: Clear stale pool mappings")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDMA client is closed during the PF reset and needs to be opened again.
Setting the flag so that RDMA client is opened in watchdog() function.
Change-ID: I507b1e4cbd05528cdff68fd360ef3dcac8901263
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Several defines and code comments were indented with spaces instead
of tabs, correct the issue to make indentation consistent.
Change-ID: I0dc6bbb990ec4a9e856acc9ec526d876181f092c
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Correcting the mutex usage, in client_subtask(), mutex_unlock has
to be called just before client_del_instance() since this function opens
and later closes the same mutex again.
Similarly in client_is_registered removing the mutex since it closes
the mutex twice.
This is a patch suggested by RDMA team.
Change-ID: Icce519c266e4221b8a2a72a15ba5bf01750e5852
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use __stringify instead.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function i40e_client_release has a print statement that uses an
adapter pointer which is not initialized if a previous if statement
is not true. Hence, intialize it in the right place.
Change-ID: I1afdaa2c46771ac42be56edcc41bb56b455b06c8
Signed-off-by: Harshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We were having a race between the completion of the client open and
calls to the client ops so don't call a client op unless we are sure the
client is open.
Testing Hints: Load IWARP driver and make sure it works as expected.
Change-Id: I741f4f2aa4fcbfdad3e40dabbbb1b005856c396b
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
i is defined as int but output as %u several times.
Adjust the format identifiers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for HMC resource and profile cmds for X722
firmware.
Change-ID: Icc332101f38ab15d1bfa167823100eb4f6822f7e
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes byte ordering problems found when enabling this feature
support. Without this patch, the feature will not work correctly. This
patch fixes the definitions to have the correct byte order.
Change-ID: Ic7489fbcbe2195df7be62ff5e359201b827cefe6
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The PF driver tells us the link speed, so do something with that
information. Add link speed to log messages, and report speed through
ethtool.
Change-Id: I279dc9540cc5203376406050a3e8d67e128d5882
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace calls to create_singlethread_workqueue instead with alloc_workqueue
as is style with other Intel drivers. This provides more control over
workqueue creation, and allows explicit setting of the desired mode of
operation. It also makes it more obvious that driver name constant is
passed to a format "%s".
Change-ID: I6192b44caf5140336cd54c5b350d51c73b541fdb
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A previous refactor added support to store user configuration for VSIs,
so that extra VSIs such as for VMDq can use this information when
configuring. Unfortunately the i40e_vsi_config_rss function was missed
in this refactor, and the values were being ignored. Fix this by
checking for the fields and using those instead of always using the
default values.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move this function below the two functions related to configuring RSS
via the admin queue. This helps co-locate the two functions, and made it
easier to spot a bug in the first i40e_config_rss_aq function as
compared to the i40e_get_rss_aq function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pool index has to be converted by get_pool helper to work correctly for
egress pool. In mlxsw the egress pool index starts from 0.
Fixes: 0f433fa0ec ("mlxsw: spectrum_buffers: Implement shared buffer configuration")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This new firmware for the qed* adpaters fixes several issues:
- Better blocking of malicious VFs.
- After FLR, Tx-switching [internal routing] of packets might
be incorrect.
- Deletion of unicast MAC filters would sometime have side-effect
of corrupting the MAC filters configred for a device.
It also contains fixes for future qed* drivers that *hopefully* would be
sent for review in the near future.
In addition, it would allow driver some new functionality, including:
- Allowing PF/VF driver compaitibility with old drivers [running
pre-8.10.5.0 firmware].
- Better debug facilities.
This would also bump the qed* driver versions to 8.10.9.20.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2016-08-18
This series contains updates to ixgbe and ixgbevf.
Emil cleans up confusing amongst the users by making an error message
into a debug message, since the TXDCTL.ENABLE (and comparable
VFTXDCTL.ENABLE for ixgbevf) bit is set only when the
transmit queue is actually enabled, which may not happen during the
configure phase eve if we waited for it. Converts to using netdev_dbg()
macro instead of our home brewed macro for ixgbevf. Converted the
service task to use atomic bitwise operations when setting and checking
reset requests to reduce the possibility of race conditions.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
An upcoming feature of IBM VNIC protocol is the ability to configure
redundant backing devices for a VNIC client. In case of a failure
on the current backing device, the driver will receive a signal
from the hypervisor indicating that a failover will occur. The driver
will then wait for a message from the backing device before
establishing a new connection.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It added reset function for RoCE driver. RoCE is a feature of hns.
In hip06 SoC, in RoCE reset process, it's needed to configure dsaf
channel reset, port and sl map info. Reset function of RoCE is
located in dsaf module, we only call it in RoCE driver when needed.
This patch is used to fix the conflict, please refer to this link:
https://www.spinics.net/lists/linux-rdma/msg39114.html
Signed-off-by: Wei Hu <xavier.huwei@huawei.com>
Signed-off-by: Nenglong Zhao <zhaonenglong@hisilicon.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Sheng Li <lisheng011@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we are in the switchdev/offloads mode, HW matching is done as
dictated by the offloaded rules and hence we don't need to enable
the ACLs mechanism used by the legacy mode.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While adding actual offloading support to the new switchdev mode, we didn't
change the setup of the send-to-vport rules to put them in the slow path
table, fix that.
Fixes: 1033665e63 ('net/mlx5: E-Switch, Use two priorities for SRIOV offloads mode')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mlx5 has also the NONE e-switch mode, we must translate from mlx5
mode to devlink mode on the devlink eswitch mode get call, do that.
While here, remove the mlx5_ prefix from the static function helpers
that deal with the mode to comply with the rest of the code.
Fixes: c930a3ad74 ('net/mlx5e: Add devlink based SRIOV mode change')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid firmware command execution each time the switchdev HW ID attr get
call is made. We do that by reading the ID (PF NIC MAC) only once at
load time and store it on the representor structure.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong key is used when extracting the address type field set by
the flower offload code. We have to use the control key and not the
basic key, fix that.
Fixes: e3a2b7ed01 ('net/mlx5e: Support offload cls_flower with drop action')
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set lastuse statistic, when number of packets is changed compared to
last query. This was wrongly dropped when bulk counter reading was added.
Fixes: a351a1b03b ('net/mlx5: Introduce bulk reading of flow counters')
Signed-off-by: Amir Vadai <amirva@mellanox.com>
Reported-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set and verify signature calculates the signature for each of the
mailbox nodes, even for those that are unused (from cache). Added
a missing length check to set and verify only those which are used.
While here, also moved the setting of msg's nodes token to where we
already go over them. This saves a pass because checksum is disabled,
and the only useful thing remaining that set signature does is setting
the token.
Fixes: e126ba97db ('mlx5: Add driver for Mellanox Connect-IB
adapters')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When PCI error is detected we should save the state of the pci prior to
disabling it.
Also when receiving pci slot reset call we need to verify that the
device is responsive.
Fixes: 89d44f0a6c ('net/mlx5_core: Add pci error handlers to mlx5_core
driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid unnecessary interface down/up operations upon an MTU change
when it does not affect the rings configuration.
Fixes: 461017cb00 ("net/mlx5e: Support RX multi-packet WQE (Striding RQ)")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Port mtu shouldn't be written to hardware on every single interface
open.
Here we set it only when needed, on change_mtu and netdevice creation.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new commmon infrastructure to allocate reosurces dynamically to
Upper layer driver's(ULD) when they register with cxgb4 driver and free
them during unregistering. All the queues and the interrupts for
them will be allocated during ULD probe only and freed during remove.
Signed-off-by: Atul Gupta <atul.gupta@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It doesn't really change anything as BGMAC_CHIPCTL_1_IF_TYPE_RMII is
equal to 0. It make code a bit clener, so far when reading it one could
think we forgot to set a proper mode. It also keeps this mode code in
sync with other ones.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
BCM53573 is a new series of Broadcom's SoCs. It's based on ARM and can
be found in two packages (versions): BCM53573 and BCM47189. It shares
some code with the Northstar family, but also requires some new quirks.
First of all there can be up to 2 Ethernet cores on this SoC. If that is
the case, they are connected to two different switch ports allowing some
more complex/optimized setups. It seems the second unit doesn't come
fully configured and requires some IRQ quirk.
Other than that only the first core is connected to the PHY. For the
second one we have to register fixed PHY (similarly to the Northstar),
otherwise generic PHY driver would get some invalid info.
This has been successfully tested on Tenda AC9 (BCM47189B0).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The division is already being done properly in efx_ef10_get_timer_config
which returns zero-on-success, unlike the old efx_ef10_get_sysclk_freq.
Fixes: d95e329a55 ("sfc: get timer configuration from adapter")
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was failing on successful registration returning meaningless errors.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Fixes: 55954f3bfd ("net: ethernet: bgmac: move BCMA MDIO Phy code into a separate file")
Signed-off-by: David S. Miller <davem@davemloft.net>
At present the code to check in kdump kernel was not disabling
allocation of resources when CONFIG_CHELSIO_T4_DCB is defined, move the
code outside #defines so that it gets disabled irrespective of #define,
when in kdump kernel.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While '0xdead' and '0xbeef' are "great" values, we should
use the correct SPEED_* values instead.
Fixes: 054c67d1c8 ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When moving into using ethtool's link_ksetting, qed started
supplying its own bitmask of speed/capabilities, but qede
is still checking for the SUPPORTED value to determine whether
it supports pause.
Fixes: 054c67d1c8 ("qed*: Add support for ethtool link_ksettings callbacks")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use atomic bitwise operations when setting and checking reset
requests. This should help with possible races in the service task.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following a write the VFTXDCTL.ENABLE bit is set only when the Tx queue
is actually enabled, which may not happen during the configure phase even
if we waited for it. Make this check debug only since this is causing
confusion with users who notice the warning in dmesg.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of the home brewed macro make use of netdev_dbg same as
the ixgbe driver.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Following a write the TXDCTL.ENABLE bit is set only when the Tx queue
is actually enabled, which may not happen during the configure phase even
if we waited for it. Make this check debug only since this is causing
confusion with users who notice the warning in dmesg.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use error "rmgr: Cannot insert RX class rule: Operation not supported" is
more meaningful than "rmgr: Cannot insert RX class rule: Unknown error 524"
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to allow for RX network flow classification to insert
and remove ethertype filter by ethtool
Example:
Add an ethertype filter:
$ ethtool -N eth0 flow-type ether proto 0x88F8 action 2
Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 1 rules
Filter: 15
Flow Type: Raw Ethernet
Src MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
Dest MAC addr: 00:00:00:00:00:00 mask: FF:FF:FF:FF:FF:FF
Ethertype: 0x88F8 mask: 0x0
Action: Direct to queue 2
Delete the filter by location:
$ ethtool -N delete 15
Signed-off-by: Ruhao Gao <ruhao.gao@ni.com>
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to allow for RX network flow classification to insert
and remove Rx filter by ethtool. Ethtool interface has it's own rules
manager
Show all filters:
$ ethtool -n eth0
4 RX rings available
Total 2 rules
Signed-off-by: Ruhao Gao <ruhao.gao@ni.com>
Signed-off-by: Gangfeng Huang <gangfeng.huang@ni.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool_ops .get_regs function attempts to read the nonexistent
register NIC_QSET_SQ_0_7_CNM_CHG, which produces a "bus error" type
OOPs.
Fix by not attempting to read, and removing the definition of,
NIC_QSET_SQ_0_7_CNM_CHG. A zero is written into the register dump to
keep the layout unchanged.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: <stable@vger.kernel.org> # 4.4.x-
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver uses netif_tx_queue_stopped() to make sure the xmit_more
indication will be honored, but that only checks for DRV_XOFF.
At the same time, it's possible that during transmission the DQL will
close the transmission queue with STACK_XOFF indication.
In re-configuration flows, when the threshold is relatively low, it's
possible that the device has no pending tranmissions, and during
tranmission the driver would miss doorbelling the HW.
Since there are no pending transmission, there will never be a Tx
completion [and thus the DQL would not remove the STACK_XOFF indication],
eventually causing the Tx queue to timeout.
While we're at it - also doorbell in case driver has to close the
transmission queue on its own [although this one is less important -
if the ring is full, we're bound to receive completion eventually,
which means the doorbell would only be postponed and not indefinetly
blocked].
Fixes: 312e06761c ("qede: Utilize xmit_more")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for sending the NCSI statistics to the
MFW. This is an asynchronous request from MFW. Upon receiving this, driver
populates the required data and send it to MFW.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for capturing stats ttl0_discard and
packet_too_big_discard in "ethtool -S" display.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the platforms like zynqmp ultrascale+ has a
separate clock gate for the rx clock. Add an optional
rx_clk so that the clock can be enabled.
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables
ip -d l
to indicate if trust is on or off for VFs.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We shifted the locking around a bit but forgot to delete this unlock so
now it can unlock twice.
Fixes: cd3be169a5 ('i40e: Move the mutex lock in i40e_client_unregister')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch implements a feature change which allows using ethtool to set
RSS hash opts using less than four parameters if desired.
Change-ID: I0fbb91255d81e997c456697c21ac39cc9754821b
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we allocate memory, we must free it. It's simple courtesy.
Change-ID: Id007294096fb53344f1a8b9a0f78eddf9853c5d6
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes the bug which causes RSS to continue to work
after being disabled. After disabling RSS, traffic would continue
to be assigned to different queues instead of falling back to a
single queue. Without this patch, attempting to disable RSS would
not work as expected. This patch fixes the bug by clearing the
lookup table used by RSS such that all traffic is assigned to a
single queue. This patch also addresses the issue of reinstating
the lookup table should RSS then be re-enabled.
Change-ID: Ib20c7c6a7e9f1f772bb787370f8a8c664796b141
Signed-off-by: Alan Brady <alan.brady@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VF goes through reset path during VF creation which happens to also
have notification of VF reset to client. Adding conditional check to
avoid wrongly notifying VF reset during VF creation.
Also changing the call order of VF enable, calling it after VF creation
rather than before.
Change-ID: I96eabd99deae746a2f0fc465194c886f196178ce
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is a fix for the bug i.e. unable to create iwarp device
in VF. This is a sync issue and the iwarp device open is called even
before the PCI register writes are done.
Forcing the PCI register writes to happen just before it exits the
function.
Change-ID: I60c6a2c709da89e845f2764cc50ce8b7373c8c44
Signed-off-by: Avinash Dayanand <avinash.dayanand@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a driver is unable to maintain all current user supplied settings
from ethtool (or other sources), it is not ok for a user request to
succeed and silently trample over previous configuration.
To that end, if you change the number of channels, it must not be
allowed to reduce the number of channels (queues) below the current
flow director filter rules targets. In this case, return -EINVAL when
a request to reduce the number of channels would do so. In addition
log a warning to the kernel buffer explaining why we failed, and report
the rules which prevent us from lowering the number of channels.
Change-ID: If41464d63d7aab11cedf09e4f3aa1a69e21ffd88
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes a problem where a static analysis tool generates
a warning for "INVARIANT_CONDITION: Expression 'enabled_tc' used
in the condition always yields the same result."
Without this patch, the driver will not pass the static analysis
tool checks without generating warnings.
This patch fixes the problem by eliminating the irrelevant check
and redundant assignment for the value of enabled_tc.
Change-ID: Ia7d44cb050f507df7de333e96369d322e08bf408
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The function calls netif_set_real_num_(tx|rx)_queues, both of which
should be done only under rntl lock. Unfortunately the
i40evf_init_task did not hold the rtnl_lock as necessary. This patch
adds the locking needed.
Change-ID: Ib72a21c3ce22b71a226b16f9bbe0f5f8cc3e849b
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we are resetting the pf stats we should also reset the RX csum
error stat.
Change-ID: I7af5ee0ec81a10f6deee1a7b8c2082ea068ef620
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When we do a reset, all the VLAN filters get added again. Therefore we also
want to reset the VLAN count to 0 or we quickly run out of filters.
Change-ID: I459f26851e22204dc8b8999928ad87cde8170119
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The client->open call in this path was not protected with the
client instance mutex, and hence the client->close can get initiated
before the open completes.
Change-Id: I0ed60c38868dd3f44966b6ed49a063d0e5b7edf5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Using list_move() instead of list_del() + list_add().
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add sniffer TX and RX namespaces to receive ingoing and outgoing
traffic.
Each outgoing/incoming packet is duplicated and steered to the sniffer
TX/RX namespace in addition to the regular flow.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
When mlx5_ib is loaded, we would like each card's IB devices
to be added according to its LAG state (one IB device, instead of
two, is to be added if LAG is active).
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add interfaces for issuing CREATE_VPORT_LAG and
DESTROY_VPORT_LAG commands.
Used for receiving PF1's eth traffic on PF0's
root ft.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
This namespace is used for LAG demux flowtable.
The idea is to position the LAG demux ft between
bypass and kernel flowtables, allowing raw-eth
traffic from both ports to be received by the PF0
IB device.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Add interfaces to allow the creation and destruction of a
LAG demux flow table.
It is a special flow table used during LAG for redirecting
non user-mode packets from PF0 to PF1 root ft, if a packet was
received on phys port two.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Until support will be added for RoCE LAG SRIOV.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
TISes belonging to the mlx5e NIC should not be
subject to port remap.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Used by IB driver for determining the IB bond
device's netdev, when LAG is active.
Returns PF0's netdev if mode is not active-backup,
or the PF netdev of the active slave when mode is
active-backup.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Available on dual port cards only, this feature keeps
track, using netdev LAG events, of the bonding
and link status of each port's PF netdev.
When both of the card's PF netdevs are enslaved to the
same bond/team master, and only them, LAG state
is active.
During LAG, only one IB device is present for both ports.
In addition to the above, this commit includes FW commands
used for managing the LAG, new facilities for adding and removing
a single device by interface, and port remap functionality according to
bond events.
Please note that this feature is currently used only for mimicking
Ethernet bonding for RoCE - netdevs functionality is not altered,
and their bonding continues to be managed solely by bond/team driver.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Exposed LAG commands enum and layouts:
- CREATE_LAG
HW enters LAG mode:
RoCE traffic from port two is received on PF0 core dev.
Allows to set tx_affinity (tx port) for QPs and TISes.
Allows to port remap QPs and TISes, overriding their
tx_affinity behavior.
- MODIFY_LAG
Remap QPs and TISes to another port.
- QUERY_LAG
Query whether LAG mode is active.
- DESTROY_LAG
HW exits LAG mode, returning to non-LAG behavior.
- CREATE_VPORT_LAG
Merge Ethernet flow steering, such that traffic received on port
two jumps to PF0 root flow table.
Available only in LAG mode.
- DESTROY_VPORT_LAG
Ethernet flow steering returns to non-LAG behavior.
Caps added:
- lag_master
Driver is in charge of managing the LAG.
This is currently the only option.
- num_lag_ports
LAG is supported only if this field's value is 2.
Other fields:
- QP/TIS tx port affinity
During LAG, this field controls on which port a QP or TIS resides.
- TIS strict tx affinity
When this field is set, the TIS will not be subject to port remap by
CREATE_LAG/MODIFY_LAG.
- LAG demux flow table
Flow table used for redirecting non user-space traffic back to
PF1 root flow table, if the packet was received on port two.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Replaced mlx5_query_port_proto_oper with separate functions per link
type. The functions should take different arguments so no point in
trying to unite them.
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The mlx5e_link_mode enumeration will also be used in mlx5_ib for RoCE.
This patch moves the enumeration to the mlx5 driver port header file.
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Use mlx5 ifc MODIFY_BITMASK_VSD in mlx5e_modify_rq_vsd and expose counter
set capability bit in hca caps structure.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Buffers powersave frame test is reversed in cfg80211, fix from Felix
Fietkau.
2) Remove bogus WARN_ON in openvswitch, from Jarno Rajahalme.
3) Fix some tg3 ethtool logic bugs, and one that would cause no
interrupts to be generated when rx-coalescing is set to 0. From
Satish Baddipadige and Siva Reddy Kallam.
4) QLCNIC mailbox corruption and napi budget handling fix from Manish
Chopra.
5) Fix fib_trie logic when walking the trie during /proc/net/route
output than can access a stale node pointer. From David Forster.
6) Several sctp_diag fixes from Phil Sutter.
7) PAUSE frame handling fixes in mlxsw driver from Ido Schimmel.
8) Checksum fixup fixes in bpf from Daniel Borkmann.
9) Memork leaks in nfnetlink, from Liping Zhang.
10) Use after free in rxrpc, from David Howells.
11) Use after free in new skb_array code of macvtap driver, from Jason
Wang.
12) Calipso resource leak, from Colin Ian King.
13) mediatek bug fixes (missing stats sync init, etc.) from Sean Wang.
14) Fix bpf non-linear packet write helpers, from Daniel Borkmann.
15) Fix lockdep splats in macsec, from Sabrina Dubroca.
16) hv_netvsc bug fixes from Vitaly Kuznetsov, mostly to do with VF
handling.
17) Various tc-action bug fixes, from CONG Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net_sched: allow flushing tc police actions
net_sched: unify the init logic for act_police
net_sched: convert tcf_exts from list to pointer array
net_sched: move tc offload macros to pkt_cls.h
net_sched: fix a typo in tc_for_each_action()
net_sched: remove an unnecessary list_del()
net_sched: remove the leftover cleanup_a()
mlxsw: spectrum: Allow packets to be trapped from any PG
mlxsw: spectrum: Unmap 802.1Q FID before destroying it
mlxsw: spectrum: Add missing rollbacks in error path
mlxsw: reg: Fix missing op field fill-up
mlxsw: spectrum: Trap loop-backed packets
mlxsw: spectrum: Add missing packet traps
mlxsw: spectrum: Mark port as active before registering it
mlxsw: spectrum: Create PVID vPort before registering netdevice
mlxsw: spectrum: Remove redundant errors from the code
mlxsw: spectrum: Don't return upon error in removal path
i40e: check for and deal with non-contiguous TCs
ixgbe: Re-enable ability to toggle VLAN filtering
ixgbe: Force VLNCTRL.VFE to be set in all VMDq paths
...
As pointed out by Jamal, an action could be shared by
multiple filters, so we can't use list to chain them
any more after we get rid of the original tc_action.
Instead, we could just save pointers to these actions
in tcf_exts, since they are refcount'ed, so convert
the list to an array of pointers.
The "ugly" part is the action API still accepts list
as a parameter, I just introduce a helper function to
convert the array of pointers to a list, instead of
relying on the C99 feature to iterate the array.
Fixes: a85a970af2 ("net_sched: move tc_action into tcf_common")
Reported-by: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2016-08-16
This series contains fixes to e1000e, igb, ixgbe and i40e.
Kshitiz Gupta provides a fix for igb to resolve the PHY delay compensation
math in several functions.
Jarod Wilson provides a fix for e1000e which had to broken up into 2
patches, first is prepares the driver for expanding the list of NICs
that have occasional ~10 hour clock jumps when being used for PTP.
Second patch actually fixes i218 silicon which has been experiencing
the clock jumps while using PTP.
Alex provides 2 patches for ixgbe now that he is back at Intel. First
fixes setting VLNCTRL.VFE bit, which was left unchanged in earlier patches
which resulted in disabling VLAN filtering for all the VFs. Second
corrects the support for disabling the VLAN tag filtering via the
feature bit.
Lastly, David fixes i40e which was causing a kernel panic when
non-contiguous traffic classes or traffic classes not starting with TC0,
were configured on a link partner switch. To fix this, changed the
logic when determining the total number of TCs enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When packets enter the device they are classified to a priority group
(PG) buffer based on their PCP value. After their egress port and
traffic class are determined they are moved to the switch's shared
buffer and await transmission, if:
(Ingress{Port}.Usage < Thres && Ingress{Port,PG}.Usage < Thres &&
Egress{Port}.Usage < Thres && Egress{Port,TC}.Usage < Thres)
||
(Ingress{Port}.Usage < Min || Ingress{Port,PG} < Min ||
Egress{Port}.Usage < Min || Egress{Port,TC}.Usage < Min)
Packets scheduled to transmission through CPU port (trapped to CPU) use
traffic class 7, which has a zero maximum and minimum quotas. However,
when such packets arrive from PG 0 they are admitted to the shared
buffer as PG 0 has a non-zero minimum quota.
Allow all packets to be trapped to the CPU - regardless of the PG they
were classified to - by assigning a 10KB minimum quota for CPU port and
TC7.
Fixes: 8e8dfe9fdf ("mlxsw: spectrum: Add IEEE 802.1Qaz ETS support")
Reported-by: Tamir Winetroub <tamirw@mellanox.com>
Tested-by: Tamir Winetroub <tamirw@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before destroying the 802.1Q FID we should first remove the VID-to-FID
mapping. This makes mlxsw_sp_fid_destroy() symmetric with regards to
mlxsw_sp_fid_create().
Fixes: 14d39461b3 ("mlxsw: spectrum: Use per-FID struct for the VLAN-aware bridge")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While going over the code I noticed we are missing two rollbacks in the
port's creation error path. Add them and adjust the place of one of them
in the port's removal sequence so that both are symmetric.
Fixes: 56ade8fe3f ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ralue pack function needs to set op, otherwise it is 0 for add always.
Fixes: d5a1c749d2 ("mlxsw: reg: Add Router Algorithmic LPM Unicast Entry Register definition")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
One of the conditions to generate an ICMP Redirect Message is that "the
packet is being forwarded out the same physical interface that it was
received from" (RFC 1812).
Therefore, we need to be able to trap such packets and let the kernel
decide what to do with them.
For each RIF, enable the loop-back filter, which will raise the LBERROR
trap whenever the ingress RIF equals the egress RIF.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Reported-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the following traps:
1) MTU Error: Trap packets whose size is bigger than the egress RIF's
MTU. If DF bit isn't set, traffic will continue to be routed in slow
path.
2) TTL Error: Trap packets whose TTL expired. This allows traceroute to
work properly.
3) OSPF packets.
Fixes: 7b27ce7bb9 ("mlxsw: spectrum: Add traps needed for router implementation")
Signed-off-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bbf2a4757b ("mlxsw: spectrum: Initialize ports at the end of
init sequence") moved ports initialization to the end of the init
sequence, which means ports are the first to be removed during fini.
Since the FDB delayed work is still active when ports are removed it's
possible for it to process FDB notifications of inactive ports,
resulting in a warning message.
Fix that by marking ports as inactive only after unregistering them. The
NETDEV_UNREGISTER event will invoke bridge's driver port removal
sequence that will cause the FDB (and FDB notifications) to be flushed.
Fixes: bbf2a4757b ("mlxsw: spectrum: Initialize ports at the end of init sequence")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After registering a netdevice it's possible for user space applications
to configure an IP address on it. From the driver's perspective, this
means a router interface (RIF) should be created for the PVID vPort.
Therefore, we must create the PVID vPort before registering the
netdevice.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when device configuration fails we emit errors to the kernel
log despite the fact we already get these from the EMAD transaction
layer, so remove them.
In addition to being unnecessary, removing these error messages will
allow us to reuse mlxsw_sp_port_add_vid() to create the PVID vPort
before registering the netdevice.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When removing a VLAN filter from the device we shouldn't return upon the
first error we encounter, as otherwise we'll have resources that will
never be freed nor used.
Instead, we should keep trying to free as much resources as possible in
a best effort mode.
Remove the error message as well, since we already get these from the
EMAD transaction code.
Fixes: 99724c18fc ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement low-level commands to support vxlan encapsulation.
Signed-off-by: Ilya Lesokhin <ilyal@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Implement the low-level part of the PF side in setting minimum
inline header mode for VFs.
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove duplicate pci dev name printing in mlx5_core_err.
Use mlx5_core_{warn,info,err} where possible to have the pci info in the
driver log messages.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Parvi Kaustubhi <parvik@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Now as all commands use mlx5 ifc interface, instead of doing two calls
for executing a command we embed command status checking into
mlx5_cmd_exec to simplify the interface.
Also we do here some cleanup for redundant software structures
(inbox/outbox) and functions and improved command failure output.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Prior to this patch we assumed that modify QP commands have the
same layout.
In ConnectX-4 for each QP transition there is a specific command
and their layout can vary.
e.g: 2err/2rst commands don't have QP context in their layout and before
this patch we posted the QP context in those commands.
Fortunately the FW only checks the suffix of the commands and executes
them, while ignoring all invalid data sent after the valid command
layout.
This patch removes mlx5_modify_qp_mbox_in and changes
mlx5_core_qp_modify to receive the required transition and QP context
with opt_param_mask if needed. This way the caller is not required to
provide the command inbox layout and it will be generated automatically.
mlx5_core_qp_modify will generate the command inbox/outbox layouts
according to the requested transition and will fill the requested
parameters.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created QP/XRCD commands layout
amd use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
The i40e driver was causing a kernel panic when
non-contiguous Traffic Classes, or Traffic Classes not
starting with TC0, were configured on a link partner switch.
i40e does not support non-contiguous TCs.
To fix this, the patch changes the logic when determining
the total number of TCs enabled. Before, this would use the
highest TC number enabled and assume that all TCs below it were
also enabled. Now, we create a bitmask of enabled TCs and scan
it to determine not only the number of TCs, but also if the set
of enabled TCs starts at zero and is contiguous. If not, then
DCB is disabled by only returning one TC.
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Back when I submitted the GSO code I messed up and dropped the support for
disabling the VLAN tag filtering via the feature bit. This patch
re-enables the use of the NETIF_F_HW_VLAN_CTAG_FILTER to enable/disable the
VLAN filtering independent of toggling promiscuous mode.
Fixes: b83e30104b ("ixgbe/ixgbevf: Add support for GSO partial")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When I was adding the code for enabling VLAN promiscuous mode with SR-IOV
enabled I had inadvertently left the VLNCTRL.VFE bit unchanged as I has
assumed there was code in another path that was setting it when we enabled
SR-IOV. This wasn't the case and as a result we were just disabling VLAN
filtering for all the VFs apparently.
Also the previous patches were always clearing CFIEN which was always set
to 0 by the hardware anyway so I am dropping the redundant bit clearing.
Fixes: 1636956491 ("ixgbe: Add support for VLAN promiscuous with SR-IOV")
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I've got reports that the Intel I-218V NIC in Intel NUC5i5RYH systems used
as a PTP slave experiences random ~10 hour clock jumps, which are resolved
if the same workaround for the 82574 and 82583 is employed, so set the
appropriate flag2 in e1000_pch_lpt_info too.
Reported-by: Rupesh Patel <rupatel@redhat.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This is prepatory work for an expanding list of adapter families that have
occasional ~10 hour clock jumps when being used for PTP. Factor out the
sanitization function and convert to using a feature (bug) flag, per
suggestion from Jesse Brandeburg.
Littering functional code with device-specific checks is much messier than
simply checking a flag, and having device-specific init set flags as needed.
There are probably a number of other cases in the e1000e code that
could/should be converted similarly.
Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix PHY delay compensation math in igb_ptp_tx_hwtstamp() and
igb_ptp_rx_rgtstamp. Add PHY delay compensation in
igb_ptp_rx_pktstamp().
In the IGB driver, there are two functions that retrieve timestamps
received by the PHY - igb_ptp_rx_rgtstamp() and igb_ptp_rx_pktstamp().
The previous commit only changed igb_ptp_rx_rgtstamp(), and the change
was incorrect.
There are two instances in which PHY delay compensations should be
made:
- Before the packet transmission over the PHY, the latency between
when the packet is timestamped and transmission of the packets,
should be an add operation, but it is currently a subtract.
- After the packets are received from the PHY, the latency between
the receiving and timestamping of the packets should be a subtract
operation, but it is currently an add.
Signed-off-by: Kshitiz Gupta <kshitiz.gupta@ni.com>
Fixes: 3f544d2 (igb: adjust ptp timestamps for tx/rx latency)
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Runtime warning occurs if DMA-API debug feature is enabled that would be
raised by pointers passed to DMA API as arguments to inconsistent struct
device objects, so that the patch makes them usage aligned between DMA
operations such as dma_map_*() and dma_unmap_*() to eliminate the warning.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 08ef55c6f2
("net-next: mediatek: fix gigabit and flow control advertisement")
had supported proper flow control settings for GMAC1. But for GMAC0,
1.GMAC0 shares the common logic with GMAC1 inside mtk_phy_link_adjust()
to adapt various settings for the target phy.
2.GMAC0 uses fixed-phy to connect to a builtin gigabit switch with
fixed link speed as commit 0c72c50f6f
("net-next: mediatek: add fixed-phy support") describes.
3.However, fixed-phy doesn't enable SUPPORTED_Pause & SUPPORTED_Asym_Pause
supported flag on default that would cause mtk_phy_link_adjust() not to
enable flow control setting on GMAC0 properly and cause packet dropped
when high traffic.
Due to these reasons, the patch adds SUPPORTED_Pause & SUPPORTED_Asym_Pause
supported flags on fixed-phy used by the driver to have proper handling on
the both GMAC with the shared common logic.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch fixes up the incorrect setup of reduced MII (RMII) on GMAC
and adds the supplement for the setup of reverse MII (REVMII) on GMAC
, and rearranges the error handling for invalid PHY argument.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the invalid dma width
error handling case instead of 0.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The null check on mdio->irq is redundant since mdio->irq is an array
of PHY_MAX_ADDR ints and hence can never be null. Remove the redundant
check.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch touches various prints in the driver - it reduces the
verbosity of some prints [which were previously logged by default]
while adding several new debug prints and modifying others.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change qed* code in trivial manner; This isn't necessarily
semantic-only, but the end result is the same, i.e., no change
should occur from user perspective. Changes include:
- Using temporary variables to better fit 80-character restrictions.
- Removal of unused variables & code with no effect.
[plus some additional minor modifications].
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make semantic-only adjustments to qed* drivers, such as:
- Changes in code indentation.
- Usage of BIT() macro.
- re-naming of variables.
- Re-ordering of variable declerations.
- Removal of (== 0) and (!= 0) in conditions.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mlxsw_sp_router_fib4_add_info_destroy(), the fib_entry pointer is used
after it has been freed by mlxsw_sp_fib_entry_destroy(). Use a temporary
variable to fix this.
Fixes: 61c503f976 ("mlxsw: spectrum_router: Implement fib4 add/del switchdev obj ops")
Signed-off-by: Vincent Stehlé <vincent.stehle@laposte.net>
Cc: Jiri Pirko <jiri@mellanox.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing free_netdev() before return from function macb_probe()
in the platform_get_irq() error handling case.
Fixes: c69618b3e4 ("net/macb: fix probe sequence to setup clocks earlier")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
'dcbx_info is malloced in qed_dcbnl_get_ieee_pfc() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: a1d8d8a51e ("qed: Add dcbnl support.")
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_set_vf_mac support which allows to set the MAC address
for cxgb4vf interfaces from the host
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Issue:
For instance, the current APIs assume a 1-to-1 mapping of Network Ports,
Physical Functions and the SR-IOV Virtual Functions of those Physical
Functions. This is not the case with our cards where any Virtual
Function can be hooked up to any Port -- or any number of Ports the
current Linux APIs also assume only 1 Network Interface/Port can be
accessed per Virtual Function.
Another issue is that these APIs assume that the Administrative Driver
is attached to the Physical Function Associated with a Virtual Function.
This is not the case with our card where all administration is performed
by a Driver which is not attached to any of the Physical Functions which
have SR-IOV PCI Capabilities.
Another consequence of these assumptions is the inability to utilize all
of the cards SR-IOV resources. For instance, our cards have SR-IOV
Capabilities on Physical Functions 0..3 and the administrative Driver
attaches to Physical Function 4. Each of the Physical Functions 0..3 can
support up to 16 Virtual Functions. With the current Linux APIs, a
2-Port card would only be able to use the Virtual Functions on Physical
Function 0..1 and not allow the Virtual Functions on Physical Functions
2..3 to be used since there are no Ports 2..3 on a 2-Port card.
Fix:
Since the control node is always the netdevice for all VF ACL commands.
Created a dummy netdevice for each Physical Function from 0 to 3 through
which one could control their VFs. The device won't be associated with
any port, since it doesn't need to transmit/receive. Its purely used
for VF management purpose only. The device will be registered only when
VF for a particular PF is configured using PCI sysfs interface and
unregistered while pci_disable_sriov() for the PF is called.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove old representation of manually created MKey/PSV commands layout,
and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created CQ commands layout,
and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created EQ commands layout,
and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created Pages management
commands layout, and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created MCG commands layout
and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created PD/UAR commands layouts
and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created ACCESS_REG/MAD_IFC
commands layout and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Remove old representation of manually created Init/Teardown hca
commands layout and use mlx5_ifc canonical structures and defines.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
This patch respell some word badly spelled.
- Invidate instead of Invalidate
- proble instead of probe
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the missing of_node_put() after finishing the usage
of of_parse_phandle() or of_node_get() used by fixed_phy.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To fix runtime warning with lockdep is enabled due that u64_stats_sync
is not initialized well, so add it.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a couple of leftover symbol conflicts caused by hashtable.h
being included by netdevice.h; those were not caught as build failure
(they're "only" a warning, but in fact real bugs). Fix those up.
Fixes: e87a8f24c ("net: resolve symbol conflicts with generic hashtable.h")
Reported-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting BGXX_SPUX_MISC_CONTROL::RX_PACKET_DIS is not needed as
packet reception is anyway disabled by BGXX_CMRX_CONFIG::DATA_PKT_RX_EN.
Also setting RX_PACKET_DIS causes a bogus remote fault condition
which delays link detection.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use standard API to generate a random RSS hash key
on every boot.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables parsing of inner layers for tunnelled packets.
Signed-off-by: Zyta Szpak <zr@semihalf.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables bulk freeing on the Tx side.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set MAC addresses only for primary VF's and don't for
secondary VFs.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When SQ/TXQ is reclaimed i.e reset it's stats also automatically reset
by HW. This is not the case with RQ. Also VF doesn't have write access
to statistics counter registers. Hence a new Mbox msg is introduced which
supports resetting RQ, SQ and full Qset stats. Currently only RQ stats
are being reset using this mbox message.
Signed-off-by: Jerin Jacob <jerin.jacob@caviumnetworks.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding debug messages in case of NACK for a mailbox message, also
did small cleanups.
Signed-off-by: Radoslaw Biernacki <rad@semihalf.com>
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of a round about way of converting buffers to SKBs and
combining them into a frag list, use standard skb_add_rx_frag()
API to merge page fragments. This code is useful when incoming
packets are of size more than RCV_FRAG_LEN which is currently
set to 2048bytes.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the way VF's irqs are visible in /proc/interrupts.
Instead of VF id, logical interface's netdev name is used for IRQ
naming and also all secondary VF's interrupts in multiqset config
use primary VF's netdev name.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
83xx has 4 BGX blocks and are enabled mixed QLM/DLM
configs. BGX0/BGX1 are from QLM2/QLM3, BGX3 is DLM4
and BGX2 is split across DLM5 & DLM6.
This patch adds support for BGX2's split config and also
enables all 4 BGXs to be used.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
83xx will have 4 BGX blocks i.e 16 LMACs, to avoid changing
the same with every platform, nicpf struct elements which
track LMAC related info are now allocated runtime based
on platform's max possible BGX count.
Also fixed configuring min packet size for all LMAC's
supported on a platform.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds RGX/RGMII interface type support to BGX
driver. This type of interface is supported by 81xx SOC.
CN81XX VNIC has 8 VFs and max possible LMAC interfaces are 9,
hence RGMII interface will not work if all DLMs are in BGX mode
and all 8 LMACs are enabled
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for QSGMII interface type to
the BGX driver. This type of interface is supported by
81xx SOC.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for BGX module on 81xx where a BGX
can be split and have different LMACs configured in
different modes.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 88xx all LMACs in a BGX will be in same mode but on 81xx
BGX can be split as two and there can be LMACs configured in
different modes.
These changes move lmac_type, lane2serdes fields into per lmac
struct from BGX struct. Got rid of qlm_mode field which has become
redundant with these changes. And now no of valid LMACs is read
from CSRs configured by low level firmware and figuring out the
same based on QLM mode is discarded
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
88xx has 128 VFs, 81xx has 8 VFs and 83xx will have 32VFs.
Made changes to PF driver such that mailbox interrupt enable
registers are configuired based on number of VFs HW supports.
Also cleanedup mailbox irq handler registration code.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unlike 88xx, CQE_RX descriptor's tunnelling extension i.e CQE_RX2_S
is always enabled on 81xx/83xx and HW does insert these fields into
CQE_RX. As a result receive buffer addresses will now be present at
7th word of CQE_RX instead of 6th.
Enable CQE_RX2_S on 88xx pass 2.x as well.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
81xx has only 4 CPUs, so it doesn't make sense to initialize
entire Qset i.e 8 queues by default. Made changes to queue
initialization to init queues equal to number of CPUs or
8 queues whichever is lesser. Also this will be applicable to
VMs with VNIC VF attached and having less VCPUs
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds info on HW maximums of 81xx/83xx and also
configures receive and transmit datapaths accordingly.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds PCI device IDs of VNIC on newer chips and also
registers VF driver with them. Device id remains same for all
versions of chips but subsystem device id changes.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current driver has most of the HW maximums info like no of channels,
traffic limiters, RSS indices e.t.c in the form of macros. These have
been moved into a 'hw_info' structure so that support for VNIC on
newer chips with different set of HW maximums can be added.
Signed-off-by: Sunil Goutham <sgoutham@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the backward compatibility on handling phy_connect(), by
iterating over the phy-handle, when new DT is used with older kernel.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 10GbE SFP+ module is not plugged in or cable is not connected,
the link status register does not report the proper state due
to floating signal. This patch checks the module present status via an
GPIO to determine whether to ignore the link status register and report
link down.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the link recovery issue, by doing PCS reset
when the link is down.
Signed-off-by: Fushen Chen <fchen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch rearranges the port initialization sequence as recommended by
hardware specification. This patch also removes, mac_init() call from
xgene_enet_link_state(), as it was not required.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes FPSel and NxtFPSel fields length to 5-bit value.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since register_netdev() call in xgene_enet_probe() was moved down to
the end, it doesn't properly handle errors that may occur, by
deconstructing everything that was setup before the error occurred.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
xgene_enet_init_hw() should delete any descriptor rings and
buffer pools setup should le_ops->cle_init() return an error.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In addition to xgene_enet_delete_bufpool() freeing skbs, their associated
dma memory should also be unmapped.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed compiler warnings reported with -Wmaybe-uninitialized W=1,
/drivers/net/ethernet/apm/xgene/xgene_enet_main.c: In function ‘xgene_enet_rx_frame’:
../drivers/net/ethernet/apm/xgene/xgene_enet_main.c:455:27: warning: variable ‘pdata’ set but not used [-Wunused-but-set-variable]
struct xgene_enet_pdata *pdata;
^
../drivers/net/ethernet/apm/xgene/xgene_enet_main.c: In function ‘xgene_enet_remove’:
../drivers/net/ethernet/apm/xgene/xgene_enet_main.c:1691:30: warning: variable ‘mac_ops’ set but not used [-Wunused-but-set-variable]
const struct xgene_mac_ops *mac_ops;
^
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On SFN8000 series adapters the MC provides a method to get the timer
quantum and the maximum timer setting. We revert to the old values if the
new call is unavailable.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFN8000-series NICs require a new method of setting interrupt moderation,
via MCDI. This is indicated by a workaround flag. This new MCDI command
takes an explicit time value rather than a number of ticks. It therefore
makes sense to also store the moderation values in terms of time, since
that is what the ethtool interface is interested in.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than explicitly specifying flags we can now specify a desired
performance target to the firmware, ie higher throughput or lower latency.
For now we use the default "auto" configuration.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since these critical sections protected by page_lock are all entered
from the user context or bottom half context, they can be replaced
with the spin_lock() or spin_lock_bh instead of spin_lock_irqsave().
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a driver for the ENA family of networking devices.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy_dev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for 64 bit addressing and BDs.
-> Enable 64 bit addressing in DMACFG register.
-> Set DMA mask when design config register shows support for 64 bit addr.
-> Add new BD words for higher address when 64 bit DMA support is present.
-> Add and update TBQPH and RBQPH for MSB of BD pointers.
-> Change extraction and updation of buffer addresses to use
64 bit address.
-> In gem_rx extract address in one place insted of two and use a
separate flag for RXUSED.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver implementation for ethtool link_ksettings
callbacks. qed driver now defines/uses the qed specific masks for
representing link capability values. qede driver maps these values to
to new link modes defined by the kernel implementation of link_ksettings.
Please consider applying this to 'net-next' branch.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ale, cpts, version, rx_packet_max, bus_freq, interrupt pacing
parameters are common per net device that uses the same h/w. So,
move them to common driver structure.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The napi structs are common for both net devices in dual_emac
mode, In order to not hold duplicate links to them, move to
cpsw_common.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These data are common for net devs in dual_emac mode. No need to hold
it for every priv instance, so move them under cpsw_common.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The irq data are common for net devs in dual_emac mode. So no need to
hold these data in every priv struct, move them under cpsw_common.
Also delete irq_num var, as after optimization it's not needed.
Correct number of irqs to 2, as anyway, driver is using only 2,
at least for now.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every net device private struct holds links to shared cpdma resources.
No need to save and every time synchronize these resources per net dev.
So, move it to common driver struct.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointers on h/w registers are common for every cpsw_private
instance, so no need to hold them for every ndev.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to hold pdev link when only dev is needed.
This allows to simplify a bunch of cpsw->pdev->dev now and farther.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simply create holder for common data and as a start moves
pdev var to it.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to check const slave num in runtime for every packet,
and ndev for slaves w/o ndev is anyway NULL. So remove redundant
check and macro.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to hold link to clk, it's used only once
while probe.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need in priv here.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
At poll handler no possibility to figure out which network device is
handling packets, as cpdma channels are common for both network
devices in dual_emac mode. Currently, the messages are printed only
for one device, in fact, there is two. This print msg is incorrect
and seems is not very useful, so drop it from poll handler.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As second net dev is created only in case of dual_emac mode, port
number can be figured out in simpler way. Also no need to pass
redundant ndev struct.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparatory patch for converting qdisc linked list into a
hashtable. As we'll need to include hashtable.h in netdevice.h, we first
have to make sure that this will not introduce symbol conflicts for any of
the netdevice.h users.
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch 'ravb: add sleep PM suspend/resume support' used incorrect
function names containing 'runtime' for the suspend and resume
functions.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interface would not function after the system had been woken up
after have been suspended (echo mem > /sys/power/state) cycle. The
reason for this is that all device registers have been reset to its
default values. This patch adds sleep suspend and resume functions that
detached the interface at suspend and restore the registers and reattach
the interface at resume.
Only the registers that are only configured at probe time needs to be
explicitly restored by the resume handler. All other registers are
reconfigured by either reopening the device in the resume handler (if
the device was running when the system was suspended) or when the
interface is opened by a user at a later time.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b5a099c67a "net: ethernet: davicom: fix devicetree irq
resource" causes an interrupt storm after the ethernet interface
is activated on S3C24XX platform (ARM non-dt), due to the interrupt
trigger type not being set properly.
It seems, after adding parsing of IRQ flags in commit 7085a7401b
"drivers: platform: parse IRQ flags from resources", there is no path
for non-dt platforms where irq_set_type callback could be invoked when
we don't pass the trigger type flags to the request_irq() call.
In case of a board where the regression is seen the interrupt trigger
type flags are passed through a platform device's resource and it is
not currently handled properly without passing the irq trigger type
flags to the request_irq() call. In case of OF an of_irq_get() call
within platform_get_irq() function seems to be ensuring required irq_chip
setup, but there is no equivalent code for non OF/ACPI platforms.
This patch mostly restores irq trigger type setting code which has been
removed in commit ("net: ethernet: davicom: fix devicetree irq resource").
Fixes: b5a099c67a ("net: ethernet: davicom: fix devicetree irq resource")
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
App count is not updated while adding new app entry to the dcbx app table.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MFW now supports the Selection field for IEEE mode. Add driver changes to
use the newer MFW masks to read/write the port-id value.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethtype value is being read incorrectly in ieee-dcbx mode. Use the
correct mfw mask value.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Endian-ness conversion is not needed for priority-to-TC field as the
field is already being read/written by the driver in big-endian way.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,x;
@@
- if (of_get_property(e1,e2,NULL))
- x = true;
- else
- x = false;
+ x = of_property_read_bool(e1,e2);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct cpdma_desc_pool->used_desc field can be safely removed from
CPDMA driver (and hot patch) because used_descs counter is used just
for pool consistency check at CPDMA deinitialization and now this
check can be re-implemnted using gen_pool_size(pool->gen_pool) !=
gen_pool_avail(pool->gen_pool).
More over, this will allow to get rid of warnings in
cpdma_desc_pool_destro()-> WARN_ON(pool->used_desc) which may happen
because the used_descs is used unprotected, since CPDMA has been
switched to use genalloc, and may get wrong values on SMP.
Hence, remove used_desc from struct cpdma_desc_pool.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool api {get|set}_settings is deprecated.
We move the mvneta driver to new api {get|set}_link_ksettings.
We use the generic function phy_ethtool_get_link_ksettings,
and update old mvneta_ethtool_set_settings to the new api.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy_dev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove global bnad_list_mutex as it is not used anymore. This makes
bnad_add_to_list() and bnad_remove_from_list() empty so remove them too.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change type of bna_id to atomic_t. The bnad_list_mutex is used to prevent
a race when bna_id is incremented. After the change the mutex can be
removed in the next step.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove global variable bnad_list and bnad->list_entry that are used
as list of bna driver instances. It is not necessary and useless.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_set_rx_mode() and ndo_add/del_vxlan_port() calls may be called with
BHs disabled. The driver currently issues the required cmds to the FW in
these contexts and polls on completions from the FW, while BHs remain
disabled. This can cause either packet loss or packet reception to be
delayed on that CPU.
This patch defers processing of the above cmds to a separate workqueue.
With this change, FW cmds are now issued only in process context.
Now that the FW cmds are issued only in process context, they can sleep
waiting for a completion instead of polling. All the spin_lock_bh(mcc_lock)
calls are now replaced with mutex calls.
Also a new rx_filter_lock is now needed to protect the RX filtering fields
like vids[] between be_vlan_add/rem_vid() and __be_set_rx_mode() contexts.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eachtime the ndo_set_rx_mode() routine is called, the driver programs the
multicast list in the adapter without checking if there are any changes to
the list. This leads to a flood of RX_FILTER cmds when a number of vlan
interfaces are configured over the device, as the ndo_ gets
called for each vlan interface. To avoid this, we now use __dev_mc_sync()
and __dev_uc_sync() API, but only to detect if there is a change in the
mc/uc lists. Now that we use this API, the code has to be-designed to
issue these API calls for each invocation of the be_set_rx_mode() call.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently removes a new vid from the adapter->vids[] array if
be_vid_config() returns an error, which occurs when there is an error in
HW/FW. This is wrong. After the HW/FW error is recovered from, we need the
complete vids[] array to re-program the vlan list.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Lancer FW has a bug due to which in some cases vlan-promisc setting
is cleared eventhough the vlan-list programming did not succeed (via
VLAN_CONFIG) cmd. The driver has no way of knowing if the vlan-promisc
mode was cleared or not when this cmd fails. To work around this issue,
this patch first explicitly clears the vlan-promisc mode via RX_FILTER
cmd and then tries to program the vlan list.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call site for this function appears as:
#ifdef DEBUG
data->msg_enable = DEBUG;
dump_eth_one(dev);
#endif
...leading to the following warning for !DEBUG builds:
drivers/net/ethernet/tundra/tsi108_eth.c:169:13: warning: 'dump_eth_one' defined but not used [-Wunused-function]
static void dump_eth_one(struct net_device *dev)
^
...when using the arch/powerpc/configs/mpc7448_hpc2_defconfig
Put the function definition under the same #ifdef as the call site
to avoid the warning.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We correctly execute mlxsw_sp_port_dcb_fini() when port is removed, but
I missed its rollback in the error path of port creation, so add it.
Fixes: f00817df2b ("mlxsw: spectrum: Introduce support for Data Center Bridging (DCB)")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PFCC register is used to configure both PAUSE and PFC frames.
Therefore, when PFC frames are disabled we must make sure we don't
mistakenly also disable PAUSE frames (which might be enabled).
Fix this by packing the PFCC register with the current PAUSE settings.
Note that this register is also accessed via ethtool ops, but there we
are guaranteed to have PFC disabled.
Fixes: d81a6bdb87 ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ieee_setpfc() gets called, PAUSE frames are not necessarily
disabled on the port.
Check if PAUSE frames are disabled or enabled and configure the port's
headroom buffer accordingly.
Fixes: d81a6bdb87 ("mlxsw: spectrum: Add IEEE 802.1Qbb PFC support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
USRIO and JUMBO CAPS have the same mask.
Fix the same.
Fixes: ce721a7021 ("net: ethernet: cadence-macb: Add disabled usrio caps")
Cc: stable@vger.kernel.org # v4.5+
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a94efbd7cc ("ethernet: arc: emac_main: add missing of_node_put
after calling of_parse_phandle") added missing of_node_put after calling
of_parse_phandle, but missing the devm_ioremap_resource() error handling
case.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Updates/fixes for iw_cxgb4 driver
- Updates/fixes for mlx5 driver
- Add flow steering and RSS API
- Add hardware stats to mlx4 and mlx5 drivers
- Add firmware version API for RDMA driver use
- Add the rxe driver (this is a software RoCE driver that makes any
Ethernet device a RoCE device)
- Fixes for i40iw driver
- Support for send only multicast joins in the cma layer
- Other minor fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oZOO
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull base rdma updates from Doug Ledford:
"Round one of 4.8 code: while this is mostly normal, there is a new
driver in here (the driver was hosted outside the kernel for several
years and is actually a fairly mature and well coded driver). It
amounts to 13,000 of the 16,000 lines of added code in here.
Summary:
- Updates/fixes for iw_cxgb4 driver
- Updates/fixes for mlx5 driver
- Add flow steering and RSS API
- Add hardware stats to mlx4 and mlx5 drivers
- Add firmware version API for RDMA driver use
- Add the rxe driver (this is a software RoCE driver that makes any
Ethernet device a RoCE device)
- Fixes for i40iw driver
- Support for send only multicast joins in the cma layer
- Other minor fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (72 commits)
Soft RoCE driver
IB/core: Support for CMA multicast join flags
IB/sa: Add cached attribute containing SM information to SA port
IB/uverbs: Fix race between uverbs_close and remove_one
IB/mthca: Clean up error unwind flow in mthca_reset()
IB/mthca: NULL arg to pci_dev_put is OK
IB/hfi1: NULL arg to sc_return_credits is OK
IB/mlx4: Add diagnostic hardware counters
net/mlx4: Query performance and diagnostics counters
net/mlx4: Add diagnostic counters capability bit
Use smaller 512 byte messages for portmapper messages
IB/ipoib: Report SG feature regardless of HW UD CSUM capability
IB/mlx4: Don't use GFP_ATOMIC for CQ resize struct
IB/hfi1: Disable by default
IB/rdmavt: Disable by default
IB/mlx5: Fix port counter ID association to QP offset
IB/mlx5: Fix iteration overrun in GSI qps
i40iw: Add NULL check for puda buffer
i40iw: Change dup_ack_thresh to u8
i40iw: Remove unnecessary check for moving CQ head
...
Add a function to query diagnostics counters from the firmware.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add a bit that indicates if the firmware supports per port
diagnostic counters.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Driver modifies the supplied NAPI budget in qlcnic_83xx_msix_tx_poll()
function. Instead, it should use the budget as it is.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a data structure corruption bug in the SRIOV VF mailbox
handler code. While handling mailbox commands from the atomic context,
driver is accessing and updating qlcnic_async_work_list_struct entry fields
in the async work list. These fields could be concurrently accessed by the
work function resulting in data corruption.
This patch restructures async mbx command handling by using a separate
async command list instead of using a list of work_struct structures.
A single work_struct is used to schedule and handle the async commands
with proper locking mechanism.
Signed-off-by: Rajesh Borundia <rajesh.borundia@qlogic.com>
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch remove the wrong substraction from info->data in
tg3_get_rxnfc function. Without this patch, the number of RSS
queues reported is less by one.
Reported-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the rx coalescing time is 0, interrupts
are not generated from the controller and rx path hangs.
To avoid this rx hang, updating the driver to not allow
rx coalescing time to be 0.
Signed-off-by: Satish Baddipadige <satish.baddipadige@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building with -Wmaybe-uninitialized shows a potential use of
an uninitialized variable:
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c: In function 'xgene_enet_phy_connect':
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c:802:23: warning: 'phy_dev' may be used uninitialized in this function [-Wmaybe-uninitialized]
Although the compiler correctly identified this based on the function,
the current code is still safe as long dev->of_node is non-NULL
for the case of CONFIG_ACPI=n, which is currently the case.
The warning is now disabled by default, but still appears when
building with W=1, and other build test tools should be able to
detect it as well. Adding an #else clause here makes the code
more robust and makes it clear to the compiler that this cannot
happen.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 8089a96f60 ("drivers: net: xgene: Add backward compatibility")
Signed-off-by: David S. Miller <davem@davemloft.net>
100g support is not available in MSI mode. Failing the driver load in this scenario.
Please consider applying this to `net'.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
This commit fixes both local (in stmmac_axi_setup) and global
(plat->phy_node) device_node for this issue, and using the
correct device node when tries to put node at stmmac_probe_config_dt
for error path.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle (or of_node_get) has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If tx timeout event occur, kernel will call rtl8139_tx_timeout_task() to reset
hardware. But in this function, driver does not stop tx and rx function before
reset hardware, that will cause system hang.
In this patch, add stop tx and rx function before reset hardware.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -EINVAL instead of 0 when EQ elements is
too larger, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge drm updates from Dave Airlie:
"This is the main drm pull request for 4.8.
I'm down with a cold at the moment so hopefully this isn't in too bad
a state, I finished pulling stuff last week mostly (nouveau fixes just
went in today), so only this message should be influenced by illness.
Apologies to anyone who's major feature I missed :-)
Core:
Lockless GEM BO freeing
Non-blocking atomic work
Documentation changes (rst/sphinx)
Prep for new fencing changes
Simple display helpers
Master/auth changes
Register/unregister rework
Loads of trivial patches/fixes.
New stuff:
ARM Mali display driver (not the 3D chip)
sii902x RGB->HDMI bridge
Panel:
Support for new panels
Improved backlight support
Bridge:
Convert ADV7511 to bridge driver
ADV7533 support
TC358767 (DSI/DPI to eDP) encoder chip support
i915:
BXT support enabled by default
GVT-g infrastructure
GuC command submission and fixes
BXT workarounds
SKL/BKL workarounds
Demidlayering device registration
Thundering herd fixes
Missing pci ids
Atomic updates
amdgpu/radeon:
ATPX improvements for better dGPU power control on PX systems
New power features for CZ/BR/ST
Pipelined BO moves and evictions in TTM
GPU scheduler improvements
GPU reset improvements
Overclocking on dGPUs with amdgpu
Polaris powermanagement enabled
nouveau:
GK20A/GM20B volt and clock improvements.
Initial support for GP100/GP104 GPUs, GP104 will not yet support
acceleration due to NVIDIA having not released firmware for them as of yet.
exynos:
Exynos5433 SoC with IOMMU support.
vc4:
Shader validation for branching
imx-drm:
Atomic mode setting conversion
Reworked DMFC FIFO allocation
External bridge support
analogix-dp:
RK3399 eDP support
Lots of fixes.
rockchip:
Lots of small fixes.
msm:
DT bindings cleanups
Shrinker and madvise support
ASoC HDMI codec support
tegra:
Host1x driver cleanups
SOR reworking for DP support
Runtime PM support
omapdrm:
PLL enhancements
Header refactoring
Gamma table support
arcgpu:
Simulator support
virtio-gpu:
Atomic modesetting fixes.
rcar-du:
Misc fixes.
mediatek:
MT8173 HDMI support
sti:
ASOC HDMI codec support
Minor fixes
fsl-dcu:
Suspend/resume support
Bridge support
amdkfd:
Minor fixes.
etnaviv:
Enable GPU clock gating
hisilicon:
Vblank and other fixes"
* tag 'drm-for-v4.8' of git://people.freedesktop.org/~airlied/linux: (1575 commits)
drm/nouveau/gr/nv3x: fix instobj write offsets in gr setup
drm/nouveau/acpi: fix lockup with PCIe runtime PM
drm/nouveau/acpi: check for function 0x1B before using it
drm/nouveau/acpi: return supported DSM functions
drm/nouveau/acpi: ensure matching ACPI handle and supported functions
drm/nouveau/fbcon: fix font width not divisible by 8
drm/amd/powerplay: remove enable_clock_power_gatings_tasks from initialize and resume events
drm/amd/powerplay: move clockgating to after ungating power in pp for uvd/vce
drm/amdgpu: add query device id and revision id into system info entry at CGS
drm/amdgpu: add new definition in bif header
drm/amd/powerplay: rename smum header guards
drm/amdgpu: enable UVD context buffer for older HW
drm/amdgpu: fix default UVD context size
drm/amdgpu: fix incorrect type of info_id
drm/amdgpu: make amdgpu_cgs_call_acpi_method as static
drm/amdgpu: comment out unused defaults_staturn_pro static const structure to fix the build
drm/amdgpu: enable UVD VM only on polaris
drm/amdgpu: increase timeout of IB test
drm/amdgpu: add destroy session when generate VCE destroy msg.
drm/amd: fix deadlock of job_list_lock V2
...
Assigning NULL to parmeter dcb has no effect outside of the
inlined function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not write random bytes from the kernel stack when
calling qed_wr.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variable length is not used after the deleted line.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
(!A || (A && B)) is equivalent to (!A || B)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
i is defined as unsigned.
So print it with %u.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
add and val are read with
sscanf(kern_buf, "%x:%x", &addr, &val);
and used as arguments for bna_reg_offset_check and writel
so they have to be unsigned.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
addr and len are read with
sscanf(kern_buf, "%x:%x", &addr, &len);
and used as arguments for
bna_reg_offset_check.
So they have to be unsigned.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If dev_get_platdata has failed pd is null.
Do not dereference a null pointer.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
i has been defined as unsigned int.
So use %u for output.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If platform_get_resource fails, mem2 is null.
Do not dereference null.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is no AC power, NIC may not work after changing mac address.
Please refer to following link.
http://www.spinics.net/lists/netdev/msg356572.html
This issue is caused by runtime power management. When there is no AC
power, if we put NIC down (ifconfig down), the driver will be in runtime
suspend state and hardware will be put into D3 state. During this time,
driver cannot access hardware regisers. So if you set new mac address
during this time, it will not be set to hardware. After resume, NIC will
keep using the old mac address and the network will not work normally.
In this patch I add detecting runtime pm status when setting mac address.
If driver is in runtime suspend state, it will skip setting mac address, keep
the new mac address, and set the new mac address during runtime resume.
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not to call rtl8169_update_counters() to dump tally counter when driver
is in runtime suspend state.
Calling rtl8169_update_counters() in runtime suspend state will produce
warning message "rtl_counters_cond == 1 (loop: 1000, delay: 10)".
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NIC will be put into D3 state during runtime suspend state. When set or
get hardware wol setting, driver will write or read hardware registers.
If we set or get hardware wol setting in runtime suspend state, because
NIC will in D3 state, the hardware registers read by driver will return all
0xff. That will let driver thinking register flag is not toggled and
then prints the warning message "rtl_counters_cond == 1 (loop: 1000,
delay: 10)" to kernel log.
For fixing this issue, add checking driver's pm runtime status in
rtl8169_get_wol() and rtl8169_set_wol().
Signed-off-by: Chunhao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistake in printk message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_platform_depopulate() in cpsw_remove() instead of
of_device_unregister(), because CSPW child devices will not be
recreated otherwise on next insmod. of_platform_depopulate() is
correct way now as it will ensure that all steps done in
of_platform_populate() are reverted, including cleaning up of
OF_POPULATED flag.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L3 error will be generated and system will crash during unloading
of CPSW driver if CPSW is used as module and ethX devices are down.
This happens because CPSW can be power off by PM runtime now when ethX
devices are down.
Hence, ensure that CPSW powered up by PM runtime before performing any
deinitialization actions which require CPSW registers access. In case
of PM runtime error just leave cpsw_remove() as we can't do anything
anymore.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix deadlock in cpdma_ctlr_destroy() which is triggered now on
cpsw module removal:
cpsw_remove()
- cpdma_ctlr_destroy()
- spin_lock_irqsave(&ctlr->lock, flags)
- cpdma_ctlr_stop()
- spin_lock_irqsave(&ctlr->lock, flags);
- cpdma_chan_destroy()
- spin_lock_irqsave(&ctlr->lock, flags);
The issue has not been observed before because CPDMA channels have
been destroyed manually by CPSW until commit d941ebe88a ("net:
ethernet: ti: cpsw: use destroy ctlr to destroy channels") was merged.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 637d3e9973 ("cxgb4: Discard the packet if the length is
greater than mtu") introduced a regression in the VLAN interface
performance when Tx VLAN offload is disabled.
Check if skb is tagged, regardless of whether it is hardware accelerated
or not. Presently we were checking only for hardware acclereated one,
which caused performance to drop to ~0.17Mbps on a 10GbE adapter for
VLAN interface, when tx vlan offload is turned off using ethtool.
The ethernet head length calculation was going wrong in this case, and
driver ended up dropping packets.
Fixes: 637d3e9973 ("cxgb4: Discard the packet if the length is greater than mtu")
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each PF/VF has a limited number of vlan filters for
configuration purposes; This information is passed to qede
and is used to prevent over-usage - once a vlan is to be
configured and no filter credit is available, the driver
would switch into working in vlan-promisc mode.
Problem is the credit pool is shared by both PFs and VFs,
and currently PFs aren't deducting the filters that are
reserved for their VFs from their quota, which may lead
to some vlan filters failing unknowingly due to lack of credit.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver uses reverse logic when checking if minimum
bandwidth configuration applied, causing it to
configure the guarantee only on the first hw-function.
Fixes: a0d26d5a4f ("qed*: Don't reset statistics on inner reload")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding the necessary logic to prevet statistics reset
on inner-reload introduced a bug, and now statistics
are reset only when re-probing the driver.
Fixes: a0d26d5a4f ("qed*: Don't reset statistics on inner reload")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before requesting the firmware to start Rx queues,
driver goes and sets the queue producer in the device to 0.
But while the producer is 32-bit, the driver currently clears 64 bits,
effectively zeroing an additional CID's producer as well.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver has reverse logic for checking the result of the
spoof-checking configuration. As a result, it would log that
the configuration failed [even though it succeeded], and will
no longer do anything when requested to remove the configuration,
as it's accounting of the feature will be incorrect.
Fixes: 6ddc760825 ("qed*: IOV support spoof-checking")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As part of ndo_vlan_rx_kill_vid() implementation,
qede is requesting firmware to remove the vlan filter.
This currently happens even if the vlan wasn't previously
added [In case device ran out of vlan credits].
For PFs this doesn't cause any issues as the firmware
would simply ignore the removal request. But for VFs their
parent PF is holding an accounting of the configured vlans,
and such a request would cause the PF to fail the VF's
removal request.
Simply fix this for both PFs & VFs and don't remove filters
that were not previously added.
Fixes: 7c1bfcad9f ("qede: Add vlan filtering offload support")
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Unified UDP encapsulation offload methods for drivers, from
Alexander Duyck.
2) Make DSA binding more sane, from Andrew Lunn.
3) Support QCA9888 chips in ath10k, from Anilkumar Kolli.
4) Several workqueue usage cleanups, from Bhaktipriya Shridhar.
5) Add XDP (eXpress Data Path), essentially running BPF programs on RX
packets as soon as the device sees them, with the option to mirror
the packet on TX via the same interface. From Brenden Blanco and
others.
6) Allow qdisc/class stats dumps to run lockless, from Eric Dumazet.
7) Add VLAN support to b53 and bcm_sf2, from Florian Fainelli.
8) Simplify netlink conntrack entry layout, from Florian Westphal.
9) Add ipv4 forwarding support to mlxsw spectrum driver, from Ido
Schimmel, Yotam Gigi, and Jiri Pirko.
10) Add SKB array infrastructure and convert tun and macvtap over to it.
From Michael S Tsirkin and Jason Wang.
11) Support qdisc packet injection in pktgen, from John Fastabend.
12) Add neighbour monitoring framework to TIPC, from Jon Paul Maloy.
13) Add NV congestion control support to TCP, from Lawrence Brakmo.
14) Add GSO support to SCTP, from Marcelo Ricardo Leitner.
15) Allow GRO and RPS to function on macsec devices, from Paolo Abeni.
16) Support MPLS over IPV4, from Simon Horman.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1622 commits)
xgene: Fix build warning with ACPI disabled.
be2net: perform temperature query in adapter regardless of its interface state
l2tp: Correctly return -EBADF from pppol2tp_getname.
net/mlx5_core/health: Remove deprecated create_singlethread_workqueue
net: ipmr/ip6mr: update lastuse on entry change
macsec: ensure rx_sa is set when validation is disabled
tipc: dump monitor attributes
tipc: add a function to get the bearer name
tipc: get monitor threshold for the cluster
tipc: make cluster size threshold for monitoring configurable
tipc: introduce constants for tipc address validation
net: neigh: disallow transition to NUD_STALE if lladdr is unchanged in neigh_update()
MAINTAINERS: xgene: Add driver and documentation path
Documentation: dtb: xgene: Add MDIO node
dtb: xgene: Add MDIO node
drivers: net: xgene: ethtool: Use phy_ethtool_gset and sset
drivers: net: xgene: Use exported functions
drivers: net: xgene: Enable MDIO driver
drivers: net: xgene: Add backward compatibility
drivers: net: phy: xgene: Add MDIO driver
...
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c: In function 'xgene_enet_phy_connect':
drivers/net/ethernet/apm/xgene/xgene_enet_hw.c:759:22: warning: unused variable 'adev' [-Wunused-variable]
Fixes: 8089a96f60 ("drivers: net: xgene: Add backward compatibility")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The be2net driver performs fw temperature queries on be_worker() routine,
which is executed each second for each be_adapter. There is a frequency
threshold to avoid fw query to happens at each call to be_worker();
instead, currently a fw query occurs once in 64 runs of the procedure.
Nevertheless, this fw temperature query is invoked only for adapters which
interface is up, so we can see I/O errors on read of hwmon counters from
userspace (from tools like lm-sensors) in case we have adapters' functions
which interface is down.
This patch moves the fw query code to be invoked even if interface is down.
No functional changes were introduced.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The workqueue health->wq was used as per device private health thread.
This was done to perform delayed work.
The workqueue has a single workitem(&health->work) and
hence doesn't require ordering. It is involved in handling the health of
the device and is not being used on a memory reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
Work item has been flushed in mlx5_health_cleanup() to ensure that
there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXlRXSAAoJEHm+PkMAQRiGG/gH/0Z8O4zWOsrwO+X1mRToRDBH
joFOjAmCVe83T1VpF5LYNB+9+owL/dEDt6+ZIswnhH7AfQPjs4RqwS4PcuMbCDVO
+mDm0PmfcKaYcQZrB2Z2OwIzRNnfCTVcsDPhIHwuIHk0m4z/xuGZonD8KoAj0+tO
3yJF6sbE1KubDVjOb+lmZZSP3cXA0pDXrNhkYhE4Tsr8fiihGjeXSNJ8t2zPLjxo
W3MPqo0rzDvQsOwoF4TWHHagVaFSJlhLBBgqu33fI7uO3jtfQD2G8wG68JCND1j3
qbMoBfTLFV/yQmSIJUt0Wv1axaCcwnjpweEB35A/GEeZ0mNB1rDdoBeI1eKEQkc=
=DGFC
-----END PGP SIGNATURE-----
Backmerge tag 'v4.7' into drm-next
Linux 4.7
As requested by Daniel Vetter as the conflicts were getting messy.
Changed SGMII 1G get_settings to use phy_ethtool_gset.
Changed SGMII 1G set_settings to use phy_ethtool_sset.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch reuses the mdio read/write and phy_register functions
and removed the local definitions.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables MDIO driver by,
- Selecting MDIO_XGENE
- Changed open and close to use phy_start and phy_stop
- Changed to use mac_ops->tx(rx)_enable and tx(rx)_disable
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds xgene_enet_check_phy_hanlde() function that checks whether
MDIO driver is probed successfully and sets pdata->mdio_driver to true.
If MDIO driver is not probed, ethernet driver falls back to backward
compatibility mode.
Since enum xgene_enet_cmd is used by MDIO driver, removing this from
ethernet driver.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes clock reset sequence.
- Added clock reset sequence for ACPI
- Added delay in clock reset sequence to make sure pulse is generated
- Added clk_unprepare_disable() in port shutdown to make sure
clock increment/decrement counts are matching
- Removed MII_MGMT_CONFIG programming, since it is not required
- Fixed programming XGENET_CONFIG_REG to enable SGMII mode
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver is configured as kernel module and when it gets
unloaded and reloaded, kernel crash was observed. This patch
addresses the software cleanup by doing the following,
- Moved register_netdev call after hardware is ready
- Since ndev is not ready, added set_irq_name to set irq name
- Since ndev is not ready, changed mdio_bus->parent to pdev->dev
- Replaced netif_start(stop)_queue by netif_tx_start(stop)_queues
- Removed napi_del call since it's called by free_netdev
- Added dev_close call, within remove
- Added shutdown callback
- Changed to use dmam_ APIs
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the driver is configured as kernel module and when it gets
unloaded and reloaded, kernel crash was observed. This patch
address the hardware resource cleanups by doing the following,
- Added mac_ops->clear() to do prefetch buffer clean up
- Fixed delete freepool buffers logic
- Reordered mac_enable and mac_disable
- Added Tx completion ring free
- Moved down delete_desc_rings after ring cleanup
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since mac_init is too heavy to be called when the link changes,
moved the speed_set configuration to a new function and added
mac_ops->set_speed function pointer. This function will be
called from adjust_link callback.
Added cases for 10/100 support for SGMII based 1G interface.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Tested-by: Fushen Chen <fchen@apm.com>
Tested-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 5741X/5731X NPAR device IDs and dual media SFP/10GBase-T device IDs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are not enough resources to enable ntuple filtering,
log a warning message.
v2: Use single message and add missing newline.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the destination MAC address in the ntuple filter structure. The
current code assumes that the destination MAC address is always the MAC
address of the NIC. This may not be true if there are macvlans, for
example. Add destination MAC address checking and configure the filter
correctly using the correct index for the destination MAC address.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slowpath completion handling is incorrectly changing
SPQ_RING_SIZE bits instead of a single one.
Fixes: 76a9a3642a ("qed: fix handling of concurrent ramrods")
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer updates from Thomas Gleixner:
"This update provides the following changes:
- The rework of the timer wheel which addresses the shortcomings of
the current wheel (cascading, slow search for next expiring timer,
etc). That's the first major change of the wheel in almost 20
years since Finn implemted it.
- A large overhaul of the clocksource drivers init functions to
consolidate the Device Tree initialization
- Some more Y2038 updates
- A capability fix for timerfd
- Yet another clock chip driver
- The usual pile of updates, comment improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (130 commits)
tick/nohz: Optimize nohz idle enter
clockevents: Make clockevents_subsys static
clocksource/drivers/time-armada-370-xp: Fix return value check
timers: Implement optimization for same expiry time in mod_timer()
timers: Split out index calculation
timers: Only wake softirq if necessary
timers: Forward the wheel clock whenever possible
timers/nohz: Remove pointless tick_nohz_kick_tick() function
timers: Optimize collect_expired_timers() for NOHZ
timers: Move __run_timers() function
timers: Remove set_timer_slack() leftovers
timers: Switch to a non-cascading wheel
timers: Reduce the CPU index space to 256k
timers: Give a few structs and members proper names
hlist: Add hlist_is_singular_node() helper
signals: Use hrtimer for sigtimedwait()
timers: Remove the deprecated mod_timer_pinned() API
timers, net/ipv4/inet: Initialize connection request timers as pinned
timers, drivers/tty/mips_ejtag: Initialize the poll timer as pinned
timers, drivers/tty/metag_da: Initialize the poll timer as pinned
...
Roger Chen