The Broadcom OSB4 IDE Controller (vendor and device IDs: 1166:0211)
does not support 64-KB DMA transfers.
Whenever a 64-KB DMA transfer is attempted,
the transfer fails and messages similar to the following
are written to the console log:
[ 2431.851125] sr 0:0:0:0: [sr0] Unhandled sense code
[ 2431.851139] sr 0:0:0:0: [sr0] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
[ 2431.851152] sr 0:0:0:0: [sr0] Sense Key : Hardware Error [current]
[ 2431.851166] sr 0:0:0:0: [sr0] Add. Sense: Logical unit communication time-out
[ 2431.851182] sr 0:0:0:0: [sr0] CDB: Read(10): 28 00 00 00 76 f4 00 00 40 00
[ 2431.851210] end_request: I/O error, dev sr0, sector 121808
When the libata and pata_serverworks modules
are recompiled with ATA_DEBUG and ATA_VERBOSE_DEBUG defined in libata.h,
the 64-KB transfer size in the scatter-gather list can be seen
in the console log:
[ 2664.897267] sr 9:0:0:0: [sr0] Send:
[ 2664.897274] 0xf63d85e0
[ 2664.897283] sr 9:0:0:0: [sr0] CDB:
[ 2664.897288] Read(10): 28 00 00 00 7f b4 00 00 40 00
[ 2664.897319] buffer = 0xf6d6fbc0, bufflen = 131072, queuecommand 0xf81b7700
[ 2664.897331] ata_scsi_dump_cdb: CDB (1:0,0,0) 28 00 00 00 7f b4 00 00 40
[ 2664.897338] ata_scsi_translate: ENTER
[ 2664.897345] ata_sg_setup: ENTER, ata1
[ 2664.897356] ata_sg_setup: 3 sg elements mapped
[ 2664.897364] ata_bmdma_fill_sg: PRD[0] = (0x66FD2000, 0xE000)
[ 2664.897371] ata_bmdma_fill_sg: PRD[1] = (0x65000000, 0x10000)
------------------------------------------------------> =======
[ 2664.897378] ata_bmdma_fill_sg: PRD[2] = (0x66A10000, 0x2000)
[ 2664.897386] ata1: ata_dev_select: ENTER, device 0, wait 1
[ 2664.897422] ata_sff_tf_load: feat 0x1 nsect 0x0 lba 0x0 0x0 0xFC
[ 2664.897428] ata_sff_tf_load: device 0xA0
[ 2664.897448] ata_sff_exec_command: ata1: cmd 0xA0
[ 2664.897457] ata_scsi_translate: EXIT
[ 2664.897462] leaving scsi_dispatch_cmnd()
[ 2664.897497] Doing sr request, dev = sr0, block = 0
[ 2664.897507] sr0 : reading 64/256 512 byte blocks.
[ 2664.897553] ata_sff_hsm_move: ata1: protocol 7 task_state 1 (dev_stat 0x58)
[ 2664.897560] atapi_send_cdb: send cdb
[ 2666.910058] ata_bmdma_port_intr: ata1: host_stat 0x64
[ 2666.910079] __ata_sff_port_intr: ata1: protocol 7 task_state 3
[ 2666.910093] ata_sff_hsm_move: ata1: protocol 7 task_state 3 (dev_stat 0x51)
[ 2666.910101] ata_sff_hsm_move: ata1: protocol 7 task_state 4 (dev_stat 0x51)
[ 2666.910129] sr 9:0:0:0: [sr0] Done:
[ 2666.910136] 0xf63d85e0 TIMEOUT
lspci shows that the driver used for the Broadcom OSB4 IDE Controller is
pata_serverworks:
00:0f.1 IDE interface: Broadcom OSB4 IDE Controller (prog-if 8e [Master SecP SecO PriP])
Flags: bus master, medium devsel, latency 64
[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
[virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=4]
I/O ports at 1440 [size=16]
Kernel driver in use: pata_serverworks
The pata_serverworks driver supports five distinct device IDs,
one being the OSB4 and the other four belonging to the CSB series.
The CSB series appears to support 64-KB DMA transfers,
as tests on a machine with an SAI2 motherboard
containing a Broadcom CSB5 IDE Controller (vendor and device IDs: 1166:0212)
showed no problems with 64-KB DMA transfers.
This problem was first discovered when attempting to install openSUSE
from a DVD on a machine with an STL2 motherboard.
Using the pata_serverworks module,
older releases of openSUSE will not install at all due to the timeouts.
Releases of openSUSE prior to 11.3 can be installed by disabling
the pata_serverworks module using the brokenmodules boot parameter,
which causes the serverworks module to be used instead.
Recent releases of openSUSE (12.2 and later) include better error recovery and
will install, though very slowly.
On all openSUSE releases, the problem can be recreated
on a machine containing a Broadcom OSB4 IDE Controller
by mounting an install DVD and running a command similar to the following:
find /mnt -type f -print | xargs cat > /dev/null
The patch below corrects the problem.
Similar to the other ATA drivers that do not support 64-KB DMA transfers,
the patch changes the ata_port_operations qc_prep vector to point to a routine
that breaks any 64-KB segment into two 32-KB segments and
changes the scsi_host_template sg_tablesize element to reduce by half
the number of scatter/gather elements allowed.
These two changes affect only the OSB4.
Signed-off-by: Scott Carter <ccscott@funsoft.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
lib/glob.c provides a new glob_match() function, with arguments in
(pattern, string) order. It replaced a private function with arguments
in (string, pattern) order, but I didn't swap the call site...
The result was the entire ATA blacklist was effectively disabled.
The lesson for today is "I f***ed up *how* badly *how* many months ago?",
er, I mean "Nobody Tests RC Kernels On Legacy Hardware".
This was not a subtle break, but it made it through an entire RC
cycle unreported, presumably because all the people doing testing
have full-featured hardware.
(FWIW, the reason for the argument swap was because fnmatch() does it that
way, and for a while implementing a full fnmatch() was being considered.)
Fixes: 428ac5fc05 (libata: Use glob_match from lib/glob.c)
Reported-by: Steven Honeyman <stevenhoneyman@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=71371#c21
Signed-off-by: George Spelvin <linux@horizon.com>
Cc: <stable@vger.kernel.org> # 3.17
Tested-by: Steven Honeyman <stevenhoneyman@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
There is no need to acquire ata_host::lock spinlock from
hardware context single IRQ interrupt handler since the
handler does not access host data that could be altered
by concurrent processors.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Split interrupt service routine into hardware context handler
and threaded context handler. That allows to protect ports with
individual locks rather than with a single host-wide lock and
move port interrupts handling out of the hardware interrupt
context.
Testing was done by transferring 8GB on two hard drives in
parallel using command 'dd if=/dev/sd{a,b} of=/dev/null'. With
lock_stat statistics I measured access times to ata_host::lock
spinlock (since interrupt handler code is fully embraced with
this lock). The average lock's holdtime decreased eight times
while average waittime decreased two times.
Both before and after the change the transfer time is the same,
while 'perf record -e cycles:k ...' shows 1%-4% CPU time spent
in ahci_single_irq_intr() routine before the update and not even
sampled/shown ahci_single_irq_intr() after the update.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
As described in AHCI v1.0 specification chapter 10.6.2.2
"Multiple MSI Based Messages" generation of interrupts
is not controlled through the HOST_IRQ_STAT register.
Considering MMIO access is expensive remove unnecessary
reading and writing of HOST_IRQ_STAT register.
Further, serializing access to the host data is no longer
needed and the interrupt service routine can avoid competing
on the host lock.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Suggested-by: "Jiang, Dave" <dave.jiang@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: "Jiang, Dave" <dave.jiang@intel.com>
Cc: linux-ide@vger.kernel.org
Currently host activation done by calling either function
ahci_host_activate() or ata_host_activate(). Consolidate
the code by only calling ahci_host_activate() for all AHCI
devices.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
This update is a prerequisite for consolidation of
AHCI host activation code within ahci_host_activate()
function.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
This update is a prerequisite for consolidation of
AHCI host activation code within ahci_host_activate()
function.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Using the SIMPLE_DEV_PM_OPS() macro can make the code shorter and cleaner.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Sharing Last Message (SLM) mode is currently checked in two
functions: ahci_host_activate() and ahci_init_interrupts().
This update consolidates SLM mode check with activation of
multiple MSIs mode.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
This patch fixes the error print invalid resource for the APM X-Gene
SoC AHCI SATA Host Controller driver. This print was due to the fact
that the controller 3 don't have a mux resource. This didn't result
in any errors but the print seems like meaningless.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The return value is not used by callers of these functions nor
by uses of all macros so change the functions to return void.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Qualcomm IPQ806x SoCs with SATA controllers need 5 clocks to be enabled.
Signed-off-by: Kumar Gala <galak@codeaurora.org>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Due to HW errata the APM X-Gene AHCI SATA host controller reports link
down even if the device presence is detected. This issue is due to speed
negotiation failure. This patch implements the algorithm to retry the
COMRESET if PxSTAT register reports device presence detected but
PHY communication not established. The maximum retry attempts are 3.
This patch also fixes the code to match the algorithm for the printing
a warning message if the disparity error still exists after link up.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch implements the feature to skip the PHY and clock
initialization if it is already configured by the firmware.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Keystone K2E EVM uses Marvel 0x9182 controller. This requires support
for the ID in the ahci driver.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: stable@vger.kernel.org
After enabled the PM feature that supporting async noirq(76569faa62
(PM / sleep: Asynchronous threads for resume_noirq)),
Jay hit the system resuming issue, that one of the JMicron controller
can not be powered up.
His device tree is like below:
+-1c.4-[02]--+-00.0 JMicron Technology Corp. JMB363 SATA/IDE Controller
| \-00.1 JMicron Technology Corp. JMB363 SATA/IDE Controller
After investigation, we found the the Micron chip 363 included
one SATA controller(0000:02:00.0) and one PATA controller(0000:02:00.1),
these two controllers do not have parent-children relationship,
but the PATA controller only can be powered on after the SATA controller
has finished the powering on.
If we enabled the async noirq(), then the below error is hit during noirq
phase:
pata_jmicron 0000:02:00.1: Refused to change power state, currently in D3
Here for JMicron chip 363/361, we need forcedly to disable the async method.
Bug detail: https://bugzilla.kernel.org/show_bug.cgi?id=81551
Reported-by: Jay <MyMailClone@t-online.de>
Signed-off-by: Chuansheng Liu <chuansheng.liu@intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The DMI table does not need to be written to, make it r/o.
Signed-off-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ahci_platform_enable_phys() and ahci_platform_disable_phys() are currently
exported, but they are not used anywhere else other than libahci_platform.c.
So make them static and do not export them to fix the following sparse
warnings:
drivers/ata/libahci_platform.c:52:5: warning: symbol 'ahci_platform_enable_phys' was not declared. Should it be static?
drivers/ata/libahci_platform.c:88:6: warning: symbol 'ahci_platform_disable_phys' was not declared. Should it be static?
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds the IDE mode SATA Device IDs for the Intel 9 Series PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
This patch adds the AHCI mode SATA Device IDs for the Intel 9 Series PCH.
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
The original version of the driver did not read the SATA calibration
fuse to remove the dependency to the fuse driver. The fuse driver
is now merged, so add this functionality.
The calibration fuse contains a 2-bit value used to pick a set
of calibration values for the SATA pad.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
IRQ flags can be obtained from resource structure, there are no need
to use additional field in the platform_data to store these values.
This patch removes this field and convert existing users of this driver
to use IRQ flags from the resources.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Tejun Heo <tj@kernel.org>
"electra-ide" is not used anywhere in the kernel and could be
represented in devicetree in a normal way.
This patch removes specific quirk for "electra-ide".
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use dev_name() instead of driver name for request_irq().
This will help to distinguish between multiple identical devices.
Before:
CPU0
5: 34425 clps711x-intc 5 pata_of_platform
6: 6778 clps711x-intc 6 pata_of_platform
After:
CPU0
5: 2182 clps711x-intc 5 20000000.ide
6: 11024 clps711x-intc 6 20100000.ide
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Tejun Heo <tj@kernel.org>
Crucial M550 may cause data corruption on queued trims and is
blacklisted. The pattern used for it fails to match 1TB one as the
capacity section will be four chars instead of three. Widen the
pattern.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Charles Reiss <woggling@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=81071
Cc: stable@vger.kernel.org
Before this patch, the driver included <linux/tegra-powergate.h>,
which was effectively renamed to <soc/tegra/pmc.h> at about the same
time the ahci_tegra series landed. Fix the include path so that the
driver compiles.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Change return type to signed int since it could be
a negative errno.
Signed-off-by: Arjun Sreedharan <arjun024@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch removes the NCQ support from the APM X-Gene SoC AHCI
Host Controller driver as it doesn't support it.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
The last user of the deprecated struct ahci_platform_data has been
cleaned up recently (SPEAr1340 got a proper PHY driver).
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Merge incoming from Andrew Morton:
- Various misc things.
- arch/sh updates.
- Part of ocfs2. Review is slow.
- Slab updates.
- Most of -mm.
- printk updates.
- lib/ updates.
- checkpatch updates.
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (226 commits)
checkpatch: update $declaration_macros, add uninitialized_var
checkpatch: warn on missing spaces in broken up quoted
checkpatch: fix false positives for --strict "space after cast" test
checkpatch: fix false positive MISSING_BREAK warnings with --file
checkpatch: add test for native c90 types in unusual order
checkpatch: add signed generic types
checkpatch: add short int to c variable types
checkpatch: add for_each tests to indentation and brace tests
checkpatch: fix brace style misuses of else and while
checkpatch: add --fix option for a couple OPEN_BRACE misuses
checkpatch: use the correct indentation for which()
checkpatch: add fix_insert_line and fix_delete_line helpers
checkpatch: add ability to insert and delete lines to patch/file
checkpatch: add an index variable for fixed lines
checkpatch: warn on break after goto or return with same tab indentation
checkpatch: emit a warning on file add/move/delete
checkpatch: add test for commit id formatting style in commit log
checkpatch: emit fewer kmalloc_array/kcalloc conversion warnings
checkpatch: improve "no space after cast" test
checkpatch: allow multiple const * types
...
This patch set consists of the usual driver updates (ufs, storvsc, pm8001
hpsa). It also has removal of the user space target driver code (everyone is
using LIO now), a partial PCI MSI-X update, more multi-queue updates,
conversion to 64 bit LUNs (so we could theoretically cope with any LUN
returned by a device) and placeholder support for the ZBC device type (Shingle
drives), plus an assortment of minor updates and bug fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJT4mS9AAoJEDeqqVYsXL0Mq34H/2AeXiM8GEVO3PIsBtF3TFZ9
poJvAyb8t//+VwAIVLHU9wrssIrIcyvNQmNHH/InGt5rOaXwGQRsnEc73bBtot4b
aC1t+hAnp2Ddvu6phmyUg7iY2GmQhAoZmeaj7krGIu2XgtLGiPg26eSsgk4Yv/U9
cuULEuOc/UnTj3w5VK8SvpyXMybVF6oQhSrS1slOglfFwPTlTI/NHU9xo7Wc3qHT
VifHXNphIvye5EH8zwtKX5p8qCrFW0pevJwyfPz7Hp2CTA9XYKx3SoeOh+n9F9ez
udBBggg7Vb1tb4mPKUoZ78UrtCVdFSCmesBU/RJe7cIh8daKaO5MVr3WPSx2JhM=
=yGai
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch set consists of the usual driver updates (ufs, storvsc,
pm8001 hpsa). It also has removal of the user space target driver
code (everyone is using LIO now), a partial PCI MSI-X update, more
multi-queue updates, conversion to 64 bit LUNs (so we could
theoretically cope with any LUN returned by a device) and placeholder
support for the ZBC device type (Shingle drives), plus an assortment
of minor updates and bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (143 commits)
scsi: do not issue SCSI RSOC command to Promise Vtrak E610f
vmw_pvscsi: Use pci_enable_msix_exact() instead of pci_enable_msix()
pm8001: Fix invalid return when request_irq() failed
lpfc: Remove superfluous call to pci_disable_msix()
isci: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Cleanup bfad_setup_intr() function
bfa: Do not call pci_enable_msix() after it failed once
fnic: Use pci_enable_msix_exact() instead of pci_enable_msix()
scsi: use short driver name for per-driver cmd slab caches
scsi_debug: support scsi-mq, queues and locks
Drivers: add blist flags
scsi: ufs: fix endianness sparse warnings
scsi: ufs: make undeclared functions static
bnx2i: Update driver version to 2.7.10.1
pm8001: fix a memory leak in nvmd_resp
pm8001: fix update_flash
pm8001: fix a memory leak in flash_update
pm8001: Cleaning up uninitialized variables
pm8001: Fix to remove null pointer checks that could never happen
...
The function may be useful for other drivers, so export it. (Suggested
by Tejun Heo.)
Note that I inverted the return value of glob_match; returning true on
match seemed to make more sense.
Signed-off-by: George Spelvin <linux@horizon.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 725c7b570f (ata: libahci_platform: move port_map parameters
into the AHCI structure) moves flags into the struct ahci_host_priv's
.flags field, which causes compiler warnings on 64-bit builds when that
value is cast to a void * pointer. Cast to an unsigned long so that the
subsequent cast to a pointer doesn't produce a warning.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The ahci_platform driver is a generic driver using the libahci_platform
functions. Add a generic compatible to avoid having an endless list of
compatibles with no differences for the same driver.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
The current implementation of the libahci does not allow to use multiple
PHYs. This patch adds the support of multiple PHYs by the libahci while
keeping the old bindings valid for device tree compatibility.
This introduce a new way of defining SATA ports in the device tree, with
one port per sub-node. This as the advantage of allowing a per port
configuration. Because some ports may be accessible but disabled in the
device tree, the port_map mask is computed automatically when using
this.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch moves force_port_map and mask_port_map into the
ahci_host_priv structure. This allows to modify them into the AHCI
framework. This is needed by the new dt bindings representing ports as
the port_map mask is computed automatically.
Parameters modifying force_port_map, mask_port_map and flags have been
removed from the ahci_platform_init_host() function, and inputs in the
ahci_host_priv structure are now directly filed.
Signed-off-by: Antoine Ténart <antoine.tenart@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
APM X-Gene SoC AHCI SATA Host controller driver requires
some correction of Phy Control OOB timing for the
COMINIT/COMWAKE parameters to correctly interoperate with
different kinds of disks.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
As per SATA IO specification, when Host sends HOLD, the device takes
about 20DW latency to reply to HOLDA. In some case, device doesn't
response to HOLDA over 20DW and causes FIFO goes into over flow
condition. Due to this condition, device enumerations fails with
those devices. This patch adjust the watermark FIFO by increasing
the FIFO depth from 0x16(default) to 0x30 to address this issue.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Make of_device_id array const, because all OF functions handle it as const.
Signed-off-by: Kiran Padwal <kiran.padwal21@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
In machines with multiple Silicon Image 3124 and/or 3132 cards, there is no
way to tell which card is the culprit when the sata_sil24 interrupt handler
gets a bad status.
Tested-by: Tim Small <tim@seoss.co.uk>
Signed-off-by: Tim Small <tim@seoss.co.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add support of the Promise FastTrak TX8660 SATA HBA in ahci mode by
registering the board in the ahci_pci_tbl[].
Note: this HBA also provide a hardware RAID mode when activated in
BIOS but specific drivers from the manufacturer are required in this
case.
Signed-off-by: Romain Degez <romain.degez@gmail.com>
Tested-by: Romain Degez <romain.degez@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
This adds support for the integrated AHCI-compliant Serial ATA
controller present on the NVIDIA Tegra124 system-on-chip.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Tegra124 SATA controller requires 4 clocks. Increase this constant
to be able to use them all.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
[linux-3.16-rc5/drivers/ata/pata_ep93xx.c:929]: (style) Checking if unsigned
variable 'irq' is less than zero.
Source code is
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
but
unsigned int irq;
$ fgrep platform_get_irq `find . -name \*.h -print`
./include/linux/platform_device.h:extern int platform_get_irq(struct
platform_device *, unsigned int);
Now using "int" type instead of "unsigned int" for "irq" variable.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=80401
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Andrey Utkin <andrey.krieger.utkin@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
libata-eh.c should handle AMNF error condition (error byte bit 0,
usually code 0x01) in libata-eh.c along with UNC as a media error so
SCSI stack can handle it properly (translation code 0x01 is already
present in libata-scsi.c) but was never passed down due to lack of
handling in EH.
While using linux-based machine (AMD 6550M-based notebook, PCI IDs for the
controller are 1022:7801 subsys 1025:059d) and ddrescue to salvage data
from failing hard drive (WD7500BPVT 2.5" 750G SATA2), I've found that pure
AMNF 0x01 error code generates generic "device error" that is retried
several times by SCSI stack instead of "media error" that is passed up to
software.
So we may assume deprecated AMNF error code is surely not dead yet, and
it's better for it to be handled properly. As we may see it is used by
modern enough devices, and used properly: drive returned AMNF only when IDs
for track cannot be read completely due to dying head or positioning,
otherwise it returned UNC(orrectables).
Not handling it causes wrong generic error code ("device error") reporting
down the stack, can damage failing drives further because of excessive
retries, and slows salvaging down a lot. Also, there is handling code in
libata-scsi.c for 0x01 AMNF error already.
https://bugzilla.kernel.org/show_bug.cgi?id=80031
tj: Shortened $SUBJ and moved its content to the first paragraph.
Signed-off-by: Alexey Asemov <alex@alex-at.ru>
Signed-off-by: Tejun Heo <tj@kernel.org>
The sata on fsl mpc8315e is broken after the commit 8a4aeec8d2
("libata/ahci: accommodate tag ordered controllers"). The reason is
that the ata controller on this SoC only implement a queue depth of
16. When issuing the commands in tag order, all the commands in tag
16 ~ 31 are mapped to tag 0 unconditionally and then causes the sata
malfunction. It makes no senses to use a 32 queue in software while
the hardware has less queue depth. So consider the queue depth
implemented by the hardware when requesting a command tag.
Fixes: 8a4aeec8d2 ("libata/ahci: accommodate tag ordered controllers")
Cc: stable@vger.kernel.org
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fixes the dma state machine lockup due to the processing
of IDENTIFY DEVICE PIO mode command. The X-Gene AHCI controller
has an errata in which it cannot clear the BSY bit after the PIO setup
FIS. The dma state machine enters CMFatalErrorUpdate state and locks
up. This patch also removes the dma restart workaround from the read_id
function as the read_id function is only called by libata layer for
ATA_INTERNAL commands. But for some cases eg: PORT MULTIPLIER
and udev, the framework will enumerate using SCSI commands and it will
not call read_id function.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The subsequent patch will make use of them.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Spread-spectrum doesn't work with Cubox-i hardware, so we have to
disable this feature. Add a DT property so that platforms can
indicate that this feature should not be enabled.
Having it as a negative property keeps existing DT files working.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Various SATA phy parameters are board specific, and therefore need to
be configured.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reviewed-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch removes support for s5pc100 ata because of no more support
S5PC100 SoC in mainline.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
When the AHCI link is disabled, it can't be re-enabled except by
resetting the entire SoC. Rather than doing this silently print
some kernel messages to inform the user, along with how to avoid
this.
tj: Put a long printf format string on a single line.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Tejun Heo <tj@kernel.org>
NCQ feature is unsupported on hisilicon sata controller, so disable
it. This version of IP is used by hip04 and hix5hd2 soc.
tj: "|=" was replaced with "=" for no reason. Restored "|=".
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Sigend-off-by: Tejun Heo <tj@kernel.org>
Doing suspend/resume on imx6q and imx53 boards with no SATA disk
attached will trigger the following warning.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 661 at drivers/ata/libahci.c:224 ahci_enable_ahci+0x74/0x8)
Modules linked in:
CPU: 0 PID: 661 Comm: sh Tainted: G W 3.15.0-rc5-next-20140521-000027
Backtrace:
[<80011c90>] (dump_backtrace) from [<80011e2c>] (show_stack+0x18/0x1c)
r6:803a22f4 r5:00000000 r4:00000000 r3:00000000
[<80011e14>] (show_stack) from [<80661e60>] (dump_stack+0x88/0xa4)
[<80661dd8>] (dump_stack) from [<80028fdc>] (warn_slowpath_common+0x70/0x94)
r5:00000009 r4:00000000
[<80028f6c>] (warn_slowpath_common) from [<80029024>] (warn_slowpath_null+0x24/)
r8:808f68c4 r7:00000000 r6:00000000 r5:00000000 r4:e0810004
[<80029000>] (warn_slowpath_null) from [<803a22f4>] (ahci_enable_ahci+0x74/0x80)
[<803a2280>] (ahci_enable_ahci) from [<803a2324>] (ahci_reset_controller+0x24/0)
r8:ddcd9410 r7:80351178 r6:ddcd9444 r5:dde8b850 r4:e0810000 r3:ddf35e90
[<803a2300>] (ahci_reset_controller) from [<803a2c68>] (ahci_platform_resume_ho)
r7:80351178 r6:ddcd9444 r5:dde8b850 r4:ddcd9410
[<803a2c30>] (ahci_platform_resume_host) from [<803a38f0>] (imx_ahci_resume+0x2)
r5:00000000 r4:ddcd9410
[<803a38c4>] (imx_ahci_resume) from [<803511ac>] (platform_pm_resume+0x34/0x54)
....
The reason is that the SATA controller has no working clock at this
point, and thus ahci_enable_ahci() fails to enable the controller. In
case that there is no SATA disk attached, the imx_sata_disable() gets
called in ahci_imx_error_handler(), and both sata_clk and sata_ref_clk
will be disabled there. Because all the imx_sata_enable() calls
afterward will return immediately due to imxpriv->no_device check, the
SATA controller working clock sata_clk will never get any chance to be
enabled again.
This is a regression caused by commit 90870d79d4 (ahci-imx: Port to
library-ised ahci_platform). Before the commit, only sata_ref_clk is
managed by the driver in enable/disable function. But after the commit,
all the clocks are enabled/disabled in a row by ahci platform helpers
ahci_platform_enable[disable]_clks. Since ahb_clk is a bus clock which
does not have gate at all, and i.MX low-power hardware module already
manages sata_clk across suspend/resume cycle, the only clock that needs
to be managed by software is sata_ref_clk.
So instead of using ahci_platform_enable[disable]_clks to manage all
the clocks in a row from imx_sata_enable[disable], we should manage
only sata_ref_clk in there.
Reported-by: Fabio Estevam <fabio.estevam@freescale.com>
Fixes: 90870d79d4 (ahci-imx: Port to library-ised ahci_platform)
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Instead of doing the check here, this should be handled
in the common AHCI platform code.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Loc Ho <lho@apm.com>
Cc: Tuan Phan <tphan@apm.com>
Cc: Suman Triphati <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The current platform AHCI driver does not set the dma_mask correctly
for 64-bit DMA capable AHCI controller. This patch checks the AHCI
capability bit and set the dma_mask and coherent_dma_mask accordingly.
Signed-off-by: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Suman Tripathi <stripathi@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ahci_platform_get_resources handles resource management for
platform AHCI drivers, including getting a possible PHY
from the device tree. Since not all drivers need a PHY, it
ignores -ENODEV and -ENOSYS from devm_get_phy. However, when
the PHY subsystem is mistakenly disabled, -ENOSYS can be
returned even when a PHY is needed.
This patch modifies the -ENOSYS case to check if a "phys"
device tree node exists. If it exists, then clearly the PHY
subsystem is mistakenly disabled and the driver cannot work,
ahci_platform_get_resources will fail and propagate the error.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Use the zeroing function instead of dma_alloc_coherent & memset(,0,)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata updates from Tejun Heo:
"Nothing too interesting - another ahci platform driver variant,
additional controller support, minor fixes and cleanups"
* 'for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: Add Device ID for HighPoint RocketRaid 642L
ata: ep93xx: use dmaengine_prep_slave_sg api instead of internal callback
ahci: add PCI ID for Marvell 88SE91A0 SATA Controller
sata_fsl: remove check for CONFIG_MPC8315_DS
ahci: add support for Hisilicon sata
libahci_platform: add host_flags parameter in ahci_platform_init_host()
ata: ahci: append new hflag AHCI_HFLAG_NO_FBS
ata: use CONFIG_PM_SLEEP instead of CONFIG_PM where applicable in host drivers
ata: ahci_mvebu: new driver for Marvell Armada 380 AHCI interfaces
Documentation: dt-bindings: reformat and order list of ahci-platform compatibles
libata-sff: remove dead code
ata: SATL compliance for Inquiry Product Revision
pata_octeon_cf: use devm_kzalloc() to allocate cf_port
This device normally comes with a proprietary driver, using a web GUI
to configure RAID:
http://www.highpoint-tech.com/USA_new/series_rr600-download.htm
But thankfully it also works out of the box with the AHCI driver,
being just a Marvell 88SE9235.
Devices 640L, 644L, 644LS should also be supported but not tested here.
Signed-off-by: Jérôme Carretero <cJ-ko@zougloub.eu>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Queued trim only works for some users with MU05 firmware. Revert to
blacklisting all firmware versions.
Introduced by commit d121f7d0cb ("libata: Update queued trim blacklist
for M5x0 drives") which this effectively reverts, while retaining the
blacklisting of M550.
See
https://bugzilla.kernel.org/show_bug.cgi?id=71371
for reports of trouble with MU05 firmware.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
it is better to use generic api instead of calling an internal callback
like channel->device->device_prep_slave_sg().
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add support for Marvell Technology Group Ltd. 88SE91A0 SATA 6Gb/s
Controller by adding its PCI ID.
Signed-off-by: Andreas Schrägle <ajs124.ajs124@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
A check for CONFIG_MPC8315_DS was added in v2.6.24. But the related
Kconfig symbol was never added to the tree. So the code behind this
check has effectively been dead for over six years. Remove it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"Mostly device-specific fixes. The only thing which isn't is the fix
for zpodd oops-on-detach bug"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: imx: PLL clock needs 100us to settle down
ata: pata_at91 only works on sam9
libata: clean up ZPODD when a port is detached
ahci: imx: software workaround for phy reset issue in resume
ahci: imx: add namespace for register enums
ahci: disable DEVSLP for Intel Valleyview
The commit e783c51 (ahci: imx: software workaround for phy reset issue
in resume) calls imx_sata_phy_reset() to reset phy immediately after
SATA MPLL is enabled. It seems working fine mostly, but fails in some
case as below.
...
ahci-imx 2200000.sata: failed to reset phy: -110
ahci-imx: probe of 2200000.sata failed with error -110
After talking to the designer, we learnt that when enabling i.MX6Q SATA
MPLL, we need to wait 100us for it to settle down for safety. Add this
required delay to fix above failure.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The hip04 SoC of hisilicon has an AHCI compliant SATA controller,
and it is compliant with the ahci 1.3 and sata 3.0 specification.
There is a wrong bit in HOST_CAP of hip04 sata controller, which
enable unsupported feature of FBS, use AHCI_HFLAG_NO_FBS hflag to
disable it.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add a dynamic host_flags argument to make ahci_platform_init_host more flexible,
then remove the AHCI_HFLAGS(...) argument from some driver's ata_port_info,
and pass that in as the new argument.
Cc: Hans de Geode <hdegoede@redhat.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Append AHCI_HFLAG_NO_FBS to force turning off FBS flag.
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@linaro.org>
Signed-off-by: Kefeng Wang <kefeng.wang@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fixes host drivers to use CONFIG_PM_SLEEP instead of CONFIG_PM
where applicable. Benefits of this change:
* unused code is not being compiled in for CONFIG_PM=y, CONFIG_PM_SLEEP=n
and CONFIG_PM_RUNTIME=y configurations
* easier transition to use struct dev_pm_ops and SIMPLE_DEV_PM_OPS() in
the future
* more consistent code (there are host drivers which are using the correct
CONFIG_PM_SLEEP checks already)
The patch leaves the core libata code and ->port_[suspend,resume] support
in sata_[inic162x,nv,sil24].c alone for now.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The smc driver used by pata_at91 is at91sam9 specific, so building
this driver on another at91 platform results in this error:
ERROR: "sam9_smc_configure" [drivers/ata/pata_at91.ko] undefined!
ERROR: "sam9_smc_write_mode" [drivers/ata/pata_at91.ko] undefined!
ERROR: "sam9_smc_read_mode" [drivers/ata/pata_at91.ko] undefined!
This patch changes the Kconfig dependency to ensure it always works.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: linux-ide@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
When a ZPODD device is unbound via sysfs, the ACPI notify handler
is not removed. This causes panics as observed in Bug #74601. The
panic only happens when the wake happens from outside the kernel
(i.e. inserting a media or pressing a button). Add a loop to
ata_port_detach which loops through the port's devices and checks
if zpodd is enabled, if so call zpodd_exit.
Cc: stable@vger.kernel.org
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The Marvell Armada 380 SoC includes two AHCI compatible
interfaces. However, like all DMA-capable Marvell interface, they
require special handling to configure MBus windows. Therefore, this
commit adds a new ahci_mvebu driver, which relies on the
libahci_platform.c code recently introduced.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
When suspending imx6q systems which have rootfs on SATA, the following
error will likely be seen in resume. The SATA link will fail to come
up, and it results in an unusable system across the suspend/resume
cycle.
$ echo mem > /sys/power/state
PM: Syncing filesystems ... done.
PM: Preparing system for mem sleep
Freezing user space processes ... (elapsed 0.002 seconds) done.
Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done.
PM: Entering mem sleep
sd 0:0:0:0: [sda] Synchronizing SCSI cache
sd 0:0:0:0: [sda] Stopping disk
PM: suspend of devices complete after 61.914 msecs
PM: suspend devices took 0.070 seconds
PM: late suspend of devices complete after 4.906 msecs
PM: noirq suspend of devices complete after 4.521 msecs
Disabling non-boot CPUs ...
CPU1: shutdown
CPU2: shutdown
CPU3: shutdown
Enabling non-boot CPUs ...
CPU1: Booted secondary processor
CPU1 is up
CPU2: Booted secondary processor
CPU2 is up
CPU3: Booted secondary processor
CPU3 is up
PM: noirq resume of devices complete after 10.486 msecs
PM: early resume of devices complete after 4.679 msecs
sd 0:0:0:0: [sda] Starting disk
PM: resume of devices complete after 22.674 msecs
PM: resume devices took 0.030 seconds
PM: Finishing wakeup.
Restarting tasks ... done.
$ ata1: SATA link down (SStatus 1 SControl 300)
ata1: SATA link down (SStatus 1 SControl 300)
ata1: limiting SATA link speed to 1.5 Gbps
ata1: SATA link down (SStatus 1 SControl 310)
ata1.00: disabled
ata1: exception Emask 0x10 SAct 0x0 SErr 0x4040000 action 0xe frozen t4
ata1: irq_stat 0x00000040, connection status changed
ata1: SError: { CommWake DevExch }
ata1: hard resetting link
sd 0:0:0:0: rejecting I/O to offline device
sd 0:0:0:0: killing request
sd 0:0:0:0: rejecting I/O to offline device
Aborting journal on device sda2-8.
sd 0:0:0:0: rejecting I/O to offline device
EXT4-fs warning (device sda2): ext4_end_bio:317: I/O error writing to inode 132577 (offset 0 size 0 starting block 26235)
Buffer I/O error on device sda2, logical block 10169
...
It's caused by a silicon issue that SATA phy does not get reset by
controller when coming back from LPM. The patch adds a software
workaround for this issue. It enforces a software reset on SATA phy
in imx_sata_enable() function, so that we can ensure SATA link will
come up properly in both power-on and resume.
The software reset is implemented by writing phy reset register through
the phy control register bus interface. Functions
imx_phy_reg_[addressing|write|read]() implement this bus interface, while
imx_sata_phy_reset() performs the actually reset operation.
Signed-off-by: Richard Zhu <r65037@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Update register enums a little bit to add proper namespace prefix, and
have the names match i.MX reference manual.
Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Ever since v2.6.19 the code contains a check for CONFIG_NO_ATA_LEGACY.
But that macro has never been defined. Apparently no one ran into
problems on platforms that do not support compatibility mode. So remove
this code that has been dead for over seven years.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Tejun Heo <tj@kernel.org>
The SCSI-to-ATA Translation standard says to use data words 25 and 26
unless they are spaces. For devices that use these words in the firmware
field, they are generally more useful anyway.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"Dan updated tag allocation to accomodate devices which choke when tags
jump back and forth. Quite a few ahci MSI related fixes. A couple
config dependency fixes and other misc fixes"
* 'for-3.15-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata/ahci: accommodate tag ordered controllers
ahci: Do not receive interrupts sent by dummy ports
ahci: Use pci_enable_msi_exact() instead of pci_enable_msi_range()
ahci: Ensure "MSI Revert to Single Message" mode is not enforced
ahci: do not request irq for dummy port
pata_samsung_cf: fix ata_host_activate() failure handling
pata_arasan_cf: fix ata_host_activate() failure handling
ata: fix i.MX AHCI driver dependencies
pata_at91: fix ata_host_activate() failure handling
libata: Update queued trim blacklist for M5x0 drives
libata: make AHCI_XGENE depend on PHY_XGENE
On Intel Valleyview SoC, SATA device sleep is not reliable. When
DEVSLP is attempted on certain SSDs, port_devslp write would fail
and result in malfunction of AHCI controller. AHCI controller may
be not shown in PCI enumeration after reset. Complete power source
removal may be required to recover from this failure. So we blacklist
this device and override host device reported capabilities such that
device LPM will only attempt slumber but not DEVSLP.
Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com>
Acked-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The AHCI spec allows implementations to issue commands in tag order
rather than FIFO order:
5.3.2.12 P:SelectCmd
HBA sets pSlotLoc = (pSlotLoc + 1) mod (CAP.NCS + 1)
or HBA selects the command to issue that has had the
PxCI bit set to '1' longer than any other command
pending to be issued.
The result is that commands posted sequentially (time-wise) may play out
of sequence when issued by hardware.
This behavior has likely been hidden by drives that arrange for commands
to complete in issue order. However, it appears recent drives (two from
different vendors that we have found so far) inflict out-of-order
completions as a matter of course. So, we need to take care to maintain
ordered submission, otherwise we risk triggering a drive to fall out of
sequential-io automation and back to random-io processing, which incurs
large latency and degrades throughput.
This issue was found in simple benchmarks where QD=2 seq-write
performance was 30-50% *greater* than QD=32 seq-write performance.
Tagging for -stable and making the change globally since it has a low
risk-to-reward ratio. Also, word is that recent versions of an unnamed
OS also does it this way now. So, drives in the field are already
experienced with this tag ordering scheme.
Cc: <stable@vger.kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Ed Ciechanowski <ed.ciechanowski@intel.com>
Reviewed-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
In multiple MSI mode all AHCI ports (including dummy) get assigned
separate MSI vectors and (as result of execution
pci_enable_msi_exact() function) separate IRQ numbers, (mapped to the
MSI vectors).
Therefore, although interrupts from dummy ports are not desired they
are still enabled. We do not request IRQs for dummy ports, but that
only means we do not assign AHCI-specific ISRs to corresponding IRQ
numbers.
As result, dummy port interrupts still could come and traverse all the
way from the PCI device to the kernel, causing unnecessary overhead.
This update disables IRQs for dummy ports and prevents the described
issue.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tested-by: David Milburn <dmilburn@redhat.com>
Cc: linux-ide@vger.kernel.org
Cc: stable@vger.kernel.org
Fixes: 5ca72c4f7c ("AHCI: Support multiple MSIs")
The driver calls pci_enable_msi_range() function with the range of
[nvec..nvec] which is what pci_enable_msi_exact() function is for.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: linux-ide@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
The AHCI specification allows hardware to choose to revert to
single MSI mode when fewer messages are allocated than requested.
Yet, at least ICH10 chipset reverts to single MSI mode even when
enough messages are allocated in some cases (see below).
This update forces the driver to not rely on initialization of
multiple MSIs mode alone and always check if "MSI Revert to
Single Message" (MRSM) mode was enforced by the controller and
fallback to the single MSI mode in case it did.
That prevents a situation when the driver configured multiple
per-port IRQ handlers, but the controller sends all port's
interrupts to a single IRQ, which could easily screw up the
interrupt handling and lead to delays and possibly crashes.
The fix was tested on a 6-port controller that successfully
reverted to the single MSI mode:
00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA
AHCI Controller (prog-if 01 [AHCI 1.0])
Subsystem: Super Micro Computer Inc Device 10a7
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 101
I/O ports at f110 [size=8]
I/O ports at f100 [size=4]
I/O ports at f0f0 [size=8]
I/O ports at f0e0 [size=4]
I/O ports at f020 [size=32]
Memory at fbf00000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable+ Count=1/16 Maskable- 64bit-
Capabilities: [70] Power Management version 3
Capabilities: [a8] SATA HBA v1.0
Capabilities: [b0] PCI Advanced Features
Kernel driver in use: ahci
With 6 ports just 8 MSI vectors should be enough, but the adapter
enforces the MRSM mode when less than 16 vectors are written to
the Multiple Messages Enable PCI register. I instigated MRSM mode
by forcing @nvec to 8 in ahci_init_interrupts().
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Cc: linux-ide@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
As a nice side effect this fixes the cf_port leak on
dma_coerce_mask_and_coherent() or ata_host_activate()
failure.
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Daney <david.daney@cavium.com>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The ahci_imx driver is only needed on Freescale i.MX platforms so
don't let it be built on other platforms, except for build test
purpose.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Richard Zhu <r65037@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add missing clk_put() call to ata_host_activate() failure path.
Sergei says,
"Hm, I have once fixed that (see that *if* (!ret)) but looks like a
later commit 477c87e908 (ARM:
at91/pata: use gpio_is_valid to check the gpio) broke it again. :-(
Would be good if the changelog did mention that..."
Cc: Andrew Victor <linux@maxim.org.za>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Crucial/Micron M500 drives properly support queued DSM TRIM starting
with firmware MU05. Update the blacklist so we only disable queued trim
for older firmware releases.
Early M550 series drives suffer from the same issue as M500. A bugfix
firmware is in the pipeline but not ready yet. Until then, blacklist
queued trim for M550.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: Chris Samuel <chris@csamuel.org>
Cc: Marc MERLIN <marc@merlins.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
AHCI_XGENE is only applicable on ARM64 but it can also be enabled for
compile testing; however, AHCI_XGENE selects PHY_XGENE which has other
arch specific dependencies. This leads to the following warning when
enabling it on other archs for compile testing.
warning: (AHCI_XGENE) selects PHY_XGENE which has unmet direct
dependencies (HAS_IOMEM && OF && (ARM64 || COMPILE_TEST))
Selecting a config option which itself has dependencies can easily
lead to broken configurations. For now, let's just make AHCI_XGENE
depend on PHY_XGENE which has all the necessary dependencies already.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Loc Ho <lho@apm.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Enumeration
- Increment max correctly in pci_scan_bridge() (Andreas Noever)
- Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
- Assign CardBus bus number only during the second pass (Andreas Noever)
- Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
- Make sure bus number resources stay within their parents bounds (Andreas Noever)
- Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
- Check for child busses which use more bus numbers than allocated (Andreas Noever)
- Don't scan random busses in pci_scan_bridge() (Andreas Noever)
- x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
- x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
- x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)
NUMA
- x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
- x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
- x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
- ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)
Resource management
- i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
- Add resource_contains() (Bjorn Helgaas)
- Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
- Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
- Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
- Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
- Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
- Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
- Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
- Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
- alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
- s390: Use generic pci_enable_resources() (Bjorn Helgaas)
- Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
- Set type in __request_region() (Bjorn Helgaas)
- Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
- Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
- Log IDE resource quirk in dmesg (Bjorn Helgaas)
- Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)
PCI device hotplug
- Make check_link_active() non-static (Rajat Jain)
- Use link change notifications for hot-plug and removal (Rajat Jain)
- Enable link state change notifications (Rajat Jain)
- Don't disable the link permanently during removal (Rajat Jain)
- Don't check adapter or latch status while disabling (Rajat Jain)
- Disable link notification across slot reset (Rajat Jain)
- Ensure very fast hotplug events are also processed (Rajat Jain)
- Add hotplug_lock to serialize hotplug events (Rajat Jain)
- Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
- Don't turn slot off when hot-added device already exists (Yijing Wang)
MSI
- Keep pci_enable_msi() documentation (Alexander Gordeev)
- ahci: Fix broken single MSI fallback (Alexander Gordeev)
- ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
- Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
- Fix leak of msi_attrs (Greg Kroah-Hartman)
- Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)
Virtualization
- Device-specific ACS support (Alex Williamson)
Freescale i.MX6
- Wait for retraining (Marek Vasut)
Marvell MVEBU
- Use Device ID and revision from underlying endpoint (Andrew Lunn)
- Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
- Call request_resource() on the apertures (Jason Gunthorpe)
- Fix potential issue in range parsing (Jean-Jacques Hiblot)
Renesas R-Car
- Check platform_get_irq() return code (Ben Dooks)
- Add error interrupt handling (Ben Dooks)
- Fix bridge logic configuration accesses (Ben Dooks)
- Register each instance independently (Magnus Damm)
- Break out window size handling (Magnus Damm)
- Make the Kconfig dependencies more generic (Magnus Damm)
Synopsys DesignWare
- Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)
Miscellaneous
- Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
- Enable INTx if BIOS left them disabled (Bjorn Helgaas)
- Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
- Clean up par-arch object file list (Liviu Dudau)
- Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
- ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
- Fix pci_bus_b() build failure (Paul Gortmaker)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=3mNS
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Enumeration
- Increment max correctly in pci_scan_bridge() (Andreas Noever)
- Clarify the "scan anyway" comment in pci_scan_bridge() (Andreas Noever)
- Assign CardBus bus number only during the second pass (Andreas Noever)
- Use request_resource_conflict() instead of insert_ for bus numbers (Andreas Noever)
- Make sure bus number resources stay within their parents bounds (Andreas Noever)
- Remove pci_fixup_parent_subordinate_busnr() (Andreas Noever)
- Check for child busses which use more bus numbers than allocated (Andreas Noever)
- Don't scan random busses in pci_scan_bridge() (Andreas Noever)
- x86: Drop pcibios_scan_root() check for bus already scanned (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_with_sysdata() (Bjorn Helgaas)
- x86: Use pcibios_scan_root() instead of pci_scan_bus_on_node() (Bjorn Helgaas)
- x86: Merge pci_scan_bus_on_node() into pcibios_scan_root() (Bjorn Helgaas)
- x86: Drop return value of pcibios_scan_root() (Bjorn Helgaas)
NUMA
- x86: Add x86_pci_root_bus_node() to look up NUMA node from PCI bus (Bjorn Helgaas)
- x86: Use x86_pci_root_bus_node() instead of get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Remove mp_bus_to_node[], set_mp_bus_to_node(), get_mp_bus_to_node() (Bjorn Helgaas)
- x86: Use NUMA_NO_NODE, not -1, for unknown node (Bjorn Helgaas)
- x86: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ia64: Use NUMA_NO_NODE, not MAX_NUMNODES, for unknown node (Bjorn Helgaas)
- ia64: Remove acpi_get_pxm() usage (Bjorn Helgaas)
- ACPI: Fix acpi_get_node() prototype (Bjorn Helgaas)
Resource management
- i2o: Fix and refactor PCI space allocation (Bjorn Helgaas)
- Add resource_contains() (Bjorn Helgaas)
- Add %pR support for IORESOURCE_UNSET (Bjorn Helgaas)
- Mark resources as IORESOURCE_UNSET if we can't assign them (Bjorn Helgaas)
- Don't clear IORESOURCE_UNSET when updating BAR (Bjorn Helgaas)
- Check IORESOURCE_UNSET before updating BAR (Bjorn Helgaas)
- Don't try to claim IORESOURCE_UNSET resources (Bjorn Helgaas)
- Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit (Bjorn Helgaas)
- Don't enable decoding if BAR hasn't been assigned an address (Bjorn Helgaas)
- Add "weak" generic pcibios_enable_device() implementation (Bjorn Helgaas)
- alpha, microblaze, sh, sparc, tile: Use default pcibios_enable_device() (Bjorn Helgaas)
- s390: Use generic pci_enable_resources() (Bjorn Helgaas)
- Don't check resource_size() in pci_bus_alloc_resource() (Bjorn Helgaas)
- Set type in __request_region() (Bjorn Helgaas)
- Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region() (Bjorn Helgaas)
- Change pci_bus_alloc_resource() type_mask to unsigned long (Bjorn Helgaas)
- Log IDE resource quirk in dmesg (Bjorn Helgaas)
- Revert "[PATCH] Insert GART region into resource map" (Bjorn Helgaas)
PCI device hotplug
- Make check_link_active() non-static (Rajat Jain)
- Use link change notifications for hot-plug and removal (Rajat Jain)
- Enable link state change notifications (Rajat Jain)
- Don't disable the link permanently during removal (Rajat Jain)
- Don't check adapter or latch status while disabling (Rajat Jain)
- Disable link notification across slot reset (Rajat Jain)
- Ensure very fast hotplug events are also processed (Rajat Jain)
- Add hotplug_lock to serialize hotplug events (Rajat Jain)
- Remove a non-existent card, regardless of "surprise" capability (Rajat Jain)
- Don't turn slot off when hot-added device already exists (Yijing Wang)
MSI
- Keep pci_enable_msi() documentation (Alexander Gordeev)
- ahci: Fix broken single MSI fallback (Alexander Gordeev)
- ahci, vfio: Use pci_enable_msi_range() (Alexander Gordeev)
- Check kmalloc() return value, fix leak of name (Greg Kroah-Hartman)
- Fix leak of msi_attrs (Greg Kroah-Hartman)
- Fix pci_msix_vec_count() htmldocs failure (Masanari Iida)
Virtualization
- Device-specific ACS support (Alex Williamson)
Freescale i.MX6
- Wait for retraining (Marek Vasut)
Marvell MVEBU
- Use Device ID and revision from underlying endpoint (Andrew Lunn)
- Fix incorrect size for PCI aperture resources (Jason Gunthorpe)
- Call request_resource() on the apertures (Jason Gunthorpe)
- Fix potential issue in range parsing (Jean-Jacques Hiblot)
Renesas R-Car
- Check platform_get_irq() return code (Ben Dooks)
- Add error interrupt handling (Ben Dooks)
- Fix bridge logic configuration accesses (Ben Dooks)
- Register each instance independently (Magnus Damm)
- Break out window size handling (Magnus Damm)
- Make the Kconfig dependencies more generic (Magnus Damm)
Synopsys DesignWare
- Fix RC BAR to be single 64-bit non-prefetchable memory (Mohit Kumar)
Miscellaneous
- Remove unused SR-IOV VF Migration support (Bjorn Helgaas)
- Enable INTx if BIOS left them disabled (Bjorn Helgaas)
- Fix hex vs decimal typo in cpqhpc_probe() (Dan Carpenter)
- Clean up par-arch object file list (Liviu Dudau)
- Set IORESOURCE_ROM_SHADOW only for the default VGA device (Sander Eikelenboom)
- ACPI, ARM, drm, powerpc, pcmcia, PCI: Use list_for_each_entry() for bus traversal (Yijing Wang)
- Fix pci_bus_b() build failure (Paul Gortmaker)"
* tag 'pci-v3.15-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (108 commits)
Revert "[PATCH] Insert GART region into resource map"
PCI: Log IDE resource quirk in dmesg
PCI: Change pci_bus_alloc_resource() type_mask to unsigned long
PCI: Check all IORESOURCE_TYPE_BITS in pci_bus_alloc_from_region()
resources: Set type in __request_region()
PCI: Don't check resource_size() in pci_bus_alloc_resource()
s390/PCI: Use generic pci_enable_resources()
tile PCI RC: Use default pcibios_enable_device()
sparc/PCI: Use default pcibios_enable_device() (Leon only)
sh/PCI: Use default pcibios_enable_device()
microblaze/PCI: Use default pcibios_enable_device()
alpha/PCI: Use default pcibios_enable_device()
PCI: Add "weak" generic pcibios_enable_device() implementation
PCI: Don't enable decoding if BAR hasn't been assigned an address
PCI: Enable INTx in pci_reenable_device() only when MSI/MSI-X not enabled
PCI: Mark 64-bit resource as IORESOURCE_UNSET if we only support 32-bit
PCI: Don't try to claim IORESOURCE_UNSET resources
PCI: Check IORESOURCE_UNSET before updating BAR
PCI: Don't clear IORESOURCE_UNSET when updating BAR
PCI: Mark resources as IORESOURCE_UNSET if we can't assign them
...
Conflicts:
arch/x86/include/asm/topology.h
drivers/ata/ahci.c
- Device PM QoS support for latency tolerance constraints on systems with
hardware interfaces allowing such constraints to be specified. That is
necessary to prevent hardware-driven power management from becoming
overly aggressive on some systems and to prevent power management
features leading to excessive latencies from being used in some cases.
- Consolidation of the handling of ACPI hotplug notifications for device
objects. This causes all device hotplug notifications to go through
the root notify handler (that was executed for all of them anyway
before) that propagates them to individual subsystems, if necessary,
by executing callbacks provided by those subsystems (those callbacks
are associated with struct acpi_device objects during device
enumeration). As a result, the code in question becomes both smaller
in size and more straightforward and all of those changes should not
affect users.
- ACPICA update, including fixes related to the handling of _PRT in cases
when it is broken and the addition of "Windows 2013" to the list of
supported "features" for _OSI (which is necessary to support systems
that work incorrectly or don't even boot without it). Changes from
Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and resume
from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan Tianyu,
Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos Karafotis,
Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and resume
from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend for
the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks to
be used during system suspend and resume more easily from Ulf Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=ywR6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"The majority of this material spent some time in linux-next, some of
it even several weeks. There are a few relatively fresh commits in
it, but they are mostly fixes and simple cleanups.
ACPI took the lead this time, both in terms of the number of commits
and the number of modified lines of code, cpufreq follows and there
are a few changes in the PM core and in cpuidle too.
A new feature that already got some LWN.net's attention is the device
PM QoS extension allowing latency tolerance requirements to be
propagated from leaf devices to their ancestors with hardware
interfaces for specifying latency tolerance. That should help systems
with hardware-driven power management to avoid going too far with it
in cases when there are latency tolerance constraints.
There also are some significant changes in the ACPI core related to
the way in which hotplug notifications are handled. They affect PCI
hotplug (ACPIPHP) and the ACPI dock station code too. The bottom line
is that all those notification now go through the root notify handler
and are propagated to the interested subsystems by means of callbacks
instead of having to install a notify handler for each device object
that we can potentially get hotplug notifications for.
In addition to that ACPICA will now advertise "Windows 2013"
compatibility for _OSI, because some systems out there don't work
correctly if that is not done (some of them don't even boot).
On the system suspend side of things, all of the device suspend and
resume callbacks, except for ->prepare() and ->complete(), are now
going to be executed asynchronously as that turns out to speed up
system suspend and resume on some platforms quite significantly and we
have a few more optimizations in that area.
Apart from that, there are some new device IDs and fixes and cleanups
all over. In particular, the system suspend and resume handling by
cpufreq should be improved and the cpuidle menu governor should be a
bit more robust now.
Specifics:
- Device PM QoS support for latency tolerance constraints on systems
with hardware interfaces allowing such constraints to be specified.
That is necessary to prevent hardware-driven power management from
becoming overly aggressive on some systems and to prevent power
management features leading to excessive latencies from being used
in some cases.
- Consolidation of the handling of ACPI hotplug notifications for
device objects. This causes all device hotplug notifications to go
through the root notify handler (that was executed for all of them
anyway before) that propagates them to individual subsystems, if
necessary, by executing callbacks provided by those subsystems
(those callbacks are associated with struct acpi_device objects
during device enumeration). As a result, the code in question
becomes both smaller in size and more straightforward and all of
those changes should not affect users.
- ACPICA update, including fixes related to the handling of _PRT in
cases when it is broken and the addition of "Windows 2013" to the
list of supported "features" for _OSI (which is necessary to
support systems that work incorrectly or don't even boot without
it). Changes from Bob Moore and Lv Zheng.
- Consolidation of ACPI _OST handling from Jiang Liu.
- ACPI battery and AC fixes allowing unusual system configurations to
be handled by that code from Alexander Mezin.
- New device IDs for the ACPI LPSS driver from Chiau Ee Chew.
- ACPI fan and thermal optimizations related to system suspend and
resume from Aaron Lu.
- Cleanups related to ACPI video from Jean Delvare.
- Assorted ACPI fixes and cleanups from Al Stone, Hanjun Guo, Lan
Tianyu, Paul Bolle, Tomasz Nowicki.
- Intel RAPL (Running Average Power Limits) driver cleanups from
Jacob Pan.
- intel_pstate fixes and cleanups from Dirk Brandewie.
- cpufreq fixes related to system suspend/resume handling from Viresh
Kumar.
- cpufreq core fixes and cleanups from Viresh Kumar, Stratos
Karafotis, Saravana Kannan, Rashika Kheria, Joe Perches.
- cpufreq drivers updates from Viresh Kumar, Zhuoyu Zhang, Rob
Herring.
- cpuidle fixes related to the menu governor from Tuukka Tikkanen.
- cpuidle fix related to coupled CPUs handling from Paul Burton.
- Asynchronous execution of all device suspend and resume callbacks,
except for ->prepare and ->complete, during system suspend and
resume from Chuansheng Liu.
- Delayed resuming of runtime-suspended devices during system suspend
for the PCI bus type and ACPI PM domain.
- New set of PM helper routines to allow device runtime PM callbacks
to be used during system suspend and resume more easily from Ulf
Hansson.
- Assorted fixes and cleanups in the PM core from Geert Uytterhoeven,
Prabhakar Lad, Philipp Zabel, Rashika Kheria, Sebastian Capella.
- devfreq fix from Saravana Kannan"
* tag 'pm+acpi-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
PM / devfreq: Rewrite devfreq_update_status() to fix multiple bugs
PM / sleep: Correct whitespace errors in <linux/pm.h>
intel_pstate: Set core to min P state during core offline
cpufreq: Add stop CPU callback to cpufreq_driver interface
cpufreq: Remove unnecessary braces
cpufreq: Fix checkpatch errors and warnings
cpufreq: powerpc: add cpufreq transition latency for FSL e500mc SoCs
MAINTAINERS: Reorder maintainer addresses for PM and ACPI
PM / Runtime: Update runtime_idle() documentation for return value meaning
video / output: Drop display output class support
fujitsu-laptop: Drop unneeded include
acer-wmi: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / gpu / drm: Stop selecting VIDEO_OUTPUT_CONTROL
ACPI / video: fix ACPI_VIDEO dependencies
cpufreq: remove unused notifier: CPUFREQ_{SUSPENDCHANGE|RESUMECHANGE}
cpufreq: Do not allow ->setpolicy drivers to provide ->target
cpufreq: arm_big_little: set 'physical_cluster' for each CPU
cpufreq: arm_big_little: make vexpress driver depend on bL core driver
ACPI / button: Add ACPI Button event via netlink routine
ACPI: Remove duplicate definitions of PREFIX
...
Pull libata updates from Tejun Heo:
"A lot of activities on libata side this time.
- A lot of changes around ahci. Various embedded platforms are
implementing ahci controllers. Some were built atop ahci_platform,
others were doing their own things. Hans made some structural
changes to libahci and librarized ahci_platform so that ahci
platform drivers can share more common code. A couple platform
drivers are added on top of that and several are added to replace
older drivers which were doing their own things (older ones are
scheduled to be removed).
- Dan finishes the patchset to make libata PM operations
asynchronous. Combined with one patch being routed through scsi,
this should speed resume measurably.
- Various fixes and cleanups from Bartlomiej and others"
* 'for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (61 commits)
ata: fix Marvell SATA driver dependencies
ata: fix ARASAN CompactFlash PATA driver dependencies
ata: remove superfluous casts
ata: sata_highbank: remove superfluous cast
ata: fix Calxeda Highbank SATA driver dependencies
ata: fix R-Car SATA driver dependencies
ARM: davinci: da850: update SATA AHCI support
ata: add new-style AHCI platform driver for DaVinci DA850 AHCI controller
ata: move library code from ahci_platform.c to libahci_platform.c
ata: ahci_platform: fix ahci_platform_data->suspend method handling
libata: remove unused ata_sas_port_async_resume() stub
libata.h: add stub for ata_sas_port_resume
libata: async resume
libata, libsas: kill pm_result and related cleanup
ata: Fix compiler warning with APM X-Gene host controller driver
arm64: Add APM X-Gene SoC AHCI SATA host controller DTS entries
ata: Add APM X-Gene SoC AHCI SATA host controller driver
Documentation: Add documentation for the APM X-Gene SoC SATA host controller DTS binding
arm64: Add APM X-Gene SoC 15Gbps Multi-purpose PHY DTS entries
ata: ahci_sunxi: fix code formatting
...
Make sata_mv host driver depend on PCI || ARCH_DOVE || ARCH_KIRKWOOD ||
ARCH_MV78XX0 || ARCH_MVEBU || ARCH_ORION5X config options as Marvell
SATA support covers both Marvell PCI devices and Marvell Dove, Kirkwood,
MV78xx0, Armada 370/XP and Orion5x SoCs (for non-PCI devices the driver
to work requires suitable device tree node or platform device to be
defined). Additionally allow the driver build if COMPILE_TEST config
option is set.
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Make pata_arasan_cf host driver depend on ARCH_SPEAR13XX config
option as ARASAN CompactFlash PATA support is specific to ST
SPEAr13xx SoCs and the driver to work requires suitable device
tree node (or platform device) to be defined. Additionally
allow the driver build if COMPILE_TEST config option is set.
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Unreferenced casts of void * types are unnecessary so remove them.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
hpriv->plat_data is 'void *' so there is no need to cast it to
'struct ecx_plat_data *'.
Cc: Mark Langsdorf <mark.langsdorf@calxeda.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Make sata_highbank host driver depend on ARCH_HIGHBANK config option
as Calxeda Highbank SATA support is specific to Calxeda Highbank
SoCs and the driver to work requires suitable device tree node to
be defined. Additionally allow the driver build if COMPILE_TEST
config option is set.
Cc: Mark Langsdorf <mark.langsdorf@calxeda.com>
Cc: Rob Herring <robh@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Make sata_rcar host driver depend on ARCH_SHMOBILE config option as
Renesas R-Car SATA support is specific to Renesas SoCs and the driver
to work requires suitable device tree node (or platform device) to be
defined. Additionally allow the driver build if COMPILE_TEST config
option is set.
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Add the new ahci_da850 host driver.
Platform changes needed to make DaVinci DA850 SATA AHCI support
fully functional are in the separate "ARM: davinci: da850: update
SATA AHCI support" commit.
Please note that this driver doesn't have the superfluous clock
control code as clock is already handled by the generic AHCI
platform library code.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Move AHCI platform library code from ahci_platform.c to
libahci_platform.c and fix dependencies for ahci_st,
ahci_imx and ahci_sunxi drivers.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Looking at ST SPEAr1340 AHCI code (the only user of the deprecated
pdata->suspend and pdata->resume) it is obvious the we should return
after calling pdata->suspend() only if the function have returned
non-zero return value. The code has been broken since commit 1e70c2
("ata/ahci_platform: Add clock framework support"). Fix it.
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Shiraz Hashim <shiraz.hashim@st.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Improve overall system resume time by making libata link recovery
actions asynchronous relative to other resume events.
Link resume operations are performed using the scsi_eh thread, so
commands, particularly the sd resume start/stop command, will be held
off until the device exits error handling. Libata already flushes eh
with ata_port_wait_eh() in the port teardown paths, so there are no
concerns with async operation colliding with the end-of-life of the
ata_port object. Also, libata-core is already careful to flush
in-flight pm operations before another round of pm starts on the given
ata_port.
Reference: https://01.org/suspendresume/blogs/tebrandt/2013/hard-disk-resume-optimization-simpler-approach
Cc: Len Brown <len.brown@intel.com>
Cc: Phillip Susi <psusi@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Todd Brandt <todd.e.brandt@linux.intel.com>
[djbw: rebase on cleanup patch, changelog wordsmithing]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Tejun says:
"At least for libata, worrying about suspend/resume failures don't make
whole lot of sense. If suspend failed, just proceed with suspend. If
the device can't be woken up afterwards, that's that. There isn't
anything we could have done differently anyway. The same for resume, if
spinup fails, the device is dud and the following commands will invoke
EH actions and will eventually fail. Again, there really isn't any
*choice* to make. Just making sure the errors are handled gracefully
(ie. don't crash) and the following commands are handled correctly
should be enough."
The only libata user that actually cares about the result from a suspend
operation is libsas. However, it only cares about whether queuing a new
operation collides with an in-flight one. All libsas does with the
error is retry, but we can just let libata wait for the previous
operation before continuing.
Other cleanups include:
1/ Unifying all ata port pm operations on an ata_port_pm_ prefix
2/ Marking all ata port pm helper routines as returning void, only
ata_port_pm_ entry points need to fake a 0 return value.
3/ Killing ata_port_{suspend|resume}_common() in favor of calling
ata_port_request_pm() directly
4/ Killing the wrappers that just do a to_ata_port() conversion
5/ Clearly marking the entry points that do async operations with an
_async suffix.
Reference: http://marc.info/?l=linux-scsi&m=138995409532286&w=2
Cc: Phillip Susi <psusi@ubuntu.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Suggested-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Todd Brandt <todd.e.brandt@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fixes an compiler warning with APM X-Gene host controller
driver when compiled with DEBUG enabled.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds support for the APM X-Gene SoC AHCI SATA host controller
driver. It requires the corresponding APM X-Gene SoC PHY driver. This
initial version only supports Gen3 speed.
Signed-off-by: Loc Ho <lho@apm.com>
Signed-off-by: Tuan Phan <tphan@apm.com>
Signed-off-by: Suman Tripathi <stripathi@apm.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
* acpi-hotplug:
ACPI / hotplug: Rework deferred execution of acpi_device_hotplug()
ACPI / dock: Update copyright notice
ACPI / dock: Drop remove_dock_dependent_devices()
ACPI / dock: Drop struct acpi_dock_ops and all code related to it
ACPI / ATA: Add hotplug contexts to ACPI companions of SATA devices
ACPI / dock: Add .uevent() callback to struct acpi_hotplug_context
ACPI / dock: Use callback pointers from devices' ACPI hotplug contexts
ACPI / dock: Use ACPI device object pointers instead of ACPI handles
ACPI / hotplug: Add .fixup() callback to struct acpi_hotplug_context
ACPI / hotplug / PCI: Do not clear event callback pointer for docks
ACPI / dock: Associate dock platform devices with ACPI device objects
ACPI / dock: Pass ACPI device pointer to acpi_device_is_battery()
ACPI / dock: Dispatch dock notifications from the global notify handler
devm_ioremap_resource() returns a pointer to the remapped memory or
an ERR_PTR() encoded error code on failure. Fix the check inside
ahci_platform_get_resources() accordingly.
Also while at it remove a needless line break.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
devm_ioremap_resource() returns a pointer to the remapped memory or
an ERR_PTR() encoded error code on failure. Fix the check inside
pata_imx_probe() accordingly.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
struct ahci_platform_data is deprecated (please see comments in
<linux/ahci_platform.h> for details). Convert ahci_st driver to
use custom ->host_stop method instead.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
* The config option for ahci_st driver was renamed from
CONFIG_SATA_AHCI_ST to CONFIG_AHCI_ST but Makefile was
not updated. Fix it (also while at it move the ahci_st
driver entry below ahci_imx and ahci_sunxi ones).
* Fix a few build issues in the ahci_st driver itself.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Now that we can directly get the ACPI device conterpart of the physical
ATA transport device, the odd_can_poweroff can be eliminated.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
If ACPI handle for an ATA device is NULL, we shouldn't call
ata_dev_get_GTF as that function will use handle to do some ACPI
evaluation.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ZPODD is built on top of runtime PM functionality, it doesn't make sense
to have it in a kernel that doesn't have CONFIG_PM_RUNTIME set.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The SC1200 is a SoC based on the Geode GX1 32-bit x86 processor, so
its drivers are only needed on this architecture, except for build
testing purpose.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
This is where we disable IRQs on suspend and update the internal
power state during suspend/resume.
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
This device is designed specifically to run on ST-Microelectronics'
hardware. To ensure no attempts are made to run on anything incompatible
we add a dependency on ST architecture
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
ata_platform_remove_one() allows us to specify our own exit function
via platform data then goes off and removes ATA Host and Port in
preparation for device removal.
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Other devices have adopted similar naming conventions which have been
accepted as the standard. This patch brings any mention of the the ST
AHCI driver into line with them.
Suggested-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
The current flow of control prevents this function from being
called. Let's remove the call.
Signed-off-by: Silvan Jegen <s.jegen@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
As far as I know, the CS5520 and CS5530 chipsets were only used with
32-bit x86 Geode processors, so I think their drivers are only needed
on this architecture, except for build testing purpose.
While we're here, simplify the dependencies for the CS5535 driver.
The CS5536 was used with the Geode processors, but also on MIPS
Loongson/Lemote 2 systems, so let its driver be built for these two
architectures only, except for build testing purpose.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Pull libata fixlet from Tejun Heo:
"I merged the two blaclist entries into 'Crucial_CT???M500SSD*'"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: use wider match for blacklisting Crucial M500
We're now blacklisting "Crucial_CT???M500SSD1" and
"Crucial_CT???M500SSD3". Also, "Micron_M500*" is blacklisted which is
about the same devices as the crucial branded ones. Let's merge the
two Crucial M500 entries and widen the match to
"Crucial_CT???M500SSD*" so that we don't have to fiddle with new
entries for similar devices.
Signed-off-by: Tejun Heo <tj@kernel.org>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable@vger.kernel.org
Prompted by the social effort in the US to discourage usage of the
adjective "retarded".
In this case we needlessly anthropomorphize hard drives. The
implication is that due to design deficiencies in the device reset
recovery time is negatively impacted. We can simply clearly state that
fact. "Exceptional devices cause outliers in reset recovery time." This
steers clear of any unintended comparison of such devices to humans with
cognitive disabilities.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Via commit 87809942d3 "libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk
for Seagate Momentus SpinPoint M8" we added a quirk for disks named
"ST1000LM024 HN-M101MBB" with firmware revision "2AR10001".
As reported on https://bugzilla.redhat.com/show_bug.cgi?id=1073901,
we need to also add firmware revision 2BA30001 as it is broken as well.
Reported-by: Nicholas <arealityfarbetween@googlemail.com>
Signed-off-by: Michele Baldessari <michele@acksyn.org>
Tested-by: Guilherme Amadio <guilherme.amadio@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
This fixes the following warnings when CONFIG_PM_SLEEP is not set:
drivers/ata/ahci_imx.c:284:12: warning: ‘imx_ahci_suspend’ defined but not used [-Wunused-function]
drivers/ata/ahci_imx.c:299:12: warning: ‘imx_ahci_resume’ defined but not used [-Wunused-function]
Reported-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Queued TRIM commands cause problems and silent file system corruption
on Crucial M500 SSDs. This patch disables them for the mSATA model of
the drive.
Signed-off-by: Marios Andreopoulos <opensource@andmarios.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org # 3.12+
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=71371
ahci_sunxi_phy_init is called from the probe and resume code paths, and
sleeping is safe in both, so use msleep instead of mdelay.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
These members are not used anywhere, and in the future we want
ahci_platform_data to go away entirely so there is no reason to keep these
around.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since the 3.13 release the ahci_imx driver has proper devicetree enabled
support for ahci on imx53 and that is used instead of the old board file
created imx53-ahci platform device.
Note this patch also complete drops the id-table, an id-table is not needed
for a single id platform driver, the name field in the driver struct suffices.
And the code already has an explicit "MODULE_ALIAS("platform:ahci");" so the
id-table is not needed for that either.
Cc: Marek Vasut <marex@denx.de>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
I've done a grep over the entire kernel tree and nothing is using this
(anymore?).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
On OMAP platforms the device needs to be runtime resumed before it can
be accessed. The OMAP HWMOD framework takes care of enabling the
module and its resources based on the device's runtime PM state.
In this patch we runtime resume during .probe() and runtime suspend
after .remove().
We also update the runtime PM state during .resume().
CC: Balaji T K <balajitk@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Some platforms have a PHY hooked up to the SATA controller. The PHY
needs to be initialized and powered up for SATA to work. We do that
using the PHY framework.
tj: Minor comment formatting updates.
CC: Balaji T K <balajitk@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo<tj@kernel.org>
Add compatible string "snps,dwc-ahci", which should be used
for Synopsis Designware SATA cores. e.g. on TI OMAP5 and DRA7 platforms.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This avoids the ugliness of creating a nested platform device from probe.
While moving it around anyways, move the mk6q phy init code from probe
to imx_sata_enable, as the phy needs to be re-initialized on resume too,
otherwise the drive won't be recognized after resume.
Tested on a wandboard i.mx6 quad.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds support for the ahci sata controler found on Allwinner A10
and A20 SoCs to the ahci_platform driver.
Orignally written by Olliver Schinagl using the approach of having a platform
device which probe method creates a new child platform device which gets
driven by ahci_platform.c, as done by ahci_imx.c .
Refactored by Hans de Goede to add most of the non sunxi specific functionality
to ahci_platform.c and use a platform_data pointer from of_device_id for the
sunxi specific bits.
Signed-off-by: Olliver Schinagl <oliver@schinagl.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Split suspend / resume code into host suspend / resume functionality and
resource enable / disabling phases, and export the new suspend_ / resume_host
functions.
tj: Minor comment formatting updates.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
ahci_probe consists of 3 steps:
1) Get resources (get mmio, clks, regulator)
2) Enable resources, handled by ahci_platform_enable_resouces
3) The more or less standard ahci-host controller init sequence
This commit refactors step 1 and 3 into separate functions, so the platform
drivers for AHCI implementations which need a specific order in step 2,
and / or need to do some custom register poking at some time, can re-use
ahci-platform.c code without needing to copy and paste it.
Note that ahci_platform_init_host's prototype takes the 3 non function
members of ahci_platform_data as arguments, the idea is that drivers using
the new exported utility functions will not use ahci_platform_data at all,
and hopefully in the future ahci_platform_data can go away entirely.
tj: Minor comment formatting updates.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
The allwinner-sun4i AHCI controller needs 2 clocks to be enabled and the
imx AHCI controller needs 3 clocks to be enabled.
tj: Minor comment formatting updates.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Allwinner A10 and A20 ARM SoCs have an AHCI sata controller which needs a
special register to be poked before starting the DMA engine.
This register gets reset on an ahci_stop_engine call, so there is no other
place then ahci_start_engine where this poking can be done.
This commit allows drivers to override ahci_start_engine behavior for use by
the Allwinner AHCI driver (and potentially other drivers in the future).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Modify the SATA subsystem to add hotplug contexts to ACPI companions
of SATA devices and ports instead of registering special ACPI dock
operations using register_hotplug_dock_device().
That change will allow the entire code handling those special ACPI
dock operations to be dropped in the next commit.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Tejun Heo <tj@kernel.org>
MSI
- Fix AHCI single-MSI fallback (Alexander Gordeev)
- Fix populate_msi_sysfs() error paths (Greg Kroah-Hartman)
- Fix htmldocs problem (Masanari Iida)
- Add pci_enable_msi_exact() and pci_enable_msix_exact() (Alexander Gordeev)
- Update documentation (Alexander Gordeev)
Miscellaneous
- mvebu: expose device ID & revision via lspci (Andrew Lunn)
- Enable INTx if the BIOS left them disabled (Bjorn Helgaas)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=CTv7
-----END PGP SIGNATURE-----
Merge tag 'pci-v3.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"The most interesting thing here is the change to enable INTx (by
clearing PCI_COMMAND_INTX_DISABLE) if the BIOS left INTx disabled.
Apparently the Baytrail BIOS does this, which means EHCI doesn't work.
Also, fix an AHCI MSI regression and other issues with the recent MSI
changes. This also adds pci_enable_msi_exact() and
pci_enable_msix_exact(), which aren't regression fixes, but will keep
us from touching drivers twice (once to stop using the deprecated
pci_enable_msi(), etc., and again to use the *_exact() variants).
There's also a minor MVEBU fix.
Summary:
MSI:
- Fix AHCI single-MSI fallback (Alexander Gordeev)
- Fix populate_msi_sysfs() error paths (Greg Kroah-Hartman)
- Fix htmldocs problem (Masanari Iida)
- Add pci_enable_msi_exact() and pci_enable_msix_exact() (Alexander Gordeev)
- Update documentation (Alexander Gordeev)
Miscellaneous:
- mvebu: expose device ID & revision via lspci (Andrew Lunn)
- Enable INTx if the BIOS left them disabled (Bjorn Helgaas)"
* tag 'pci-v3.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
ahci: Fix broken fallback to single MSI mode
PCI: Enable INTx if BIOS left them disabled
PCI/MSI: Add pci_enable_msi_exact() and pci_enable_msix_exact()
PCI/MSI: Fix cut-and-paste errors in documentation
PCI/MSI: Add pci_enable_msi() documentation back
PCI/MSI: Fix pci_msix_vec_count() htmldocs failure
PCI/MSI: Fix leak of msi_attrs
PCI/MSI: Check kmalloc() return value, fix leak of name
PCI: mvebu: Use Device ID and revision from underlying endpoint
Pull libata fixes from Tejun Heo:
"Various device specific fixes. Nothing too interesting"
* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ahci: disable NCQ on Samsung pci-e SSDs on macbooks
ata: sata_mv: Cleanup only the initialized ports
sata_sil: apply MOD15WRITE quirk to TOSHIBA MK2561GSYN
ata: enable quirk from jmicron JMB350 for JMB394
ATA: SATA_MV: Add missing Kconfig select statememnt
ata: pata_imx: Check the return value from clk_prepare_enable()
sparse says:
drivers/ata/libahci.c:1390:5: warning:
symbol 'ahci_pmp_retry_softreset' was not declared. Should it be static?
Signed-off-by: Daeseok Youn <daeseok.youn@gmail.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch fix spelling typo in Documentation/DocBook.
It is because .html and .xml files are generated by make htmldocs,
I have to fix a typo within the source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Let users know that CONFIG_ATA is the kconfig symbol for libata,
since libata is mentioned in documentation and messages several
times.
Also correct a grammar typo.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
No need to return a 'fake' return value on platform_get_irq() failure.
Just return the error code itself instead.
Also, change the error condition to irq < 0, so that only negative values
are treated as errors.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Using devm_ioremap_resource() can lead to code simplication, as we don't need
to explicitily check for error returned by platform_get_resource().
Also, no need to print an error message when devm_ioremap_resource() fails,
as the OOM code code will shout loudly on such condition.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Samsung's pci-e SSDs with device ID 0x1600 which are found on some
macbooks time out on NCQ commands. Blacklist NCQ on the device so
that the affected machines can at least boot.
Original-patch-by: Levente Kurusa <levex@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=60731
Cc: stable@vger.kernel.org
When an error occurs in the port initialization loop, currently the
driver tries to cleanup all the ports. This results in a NULL pointer
dereference if the ports were only partially initialized.
Fix this by updating only the number of initialized ports (either
with failure or successfully), before jumping to the error path
and looping over that number in the cleanup loop.
Cc: Andrew Lunn <andrew@lunn.ch>
Reported-by: Mikael Pettersson <mikpelinux@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
Commit 7b92b4f61e ("PCI/MSI: Remove pci_enable_msi_block_auto()")
introduced a regression: if multiple MSI initialization fails, the code
falls back to INTx rather than to single MSI.
Fixes: 7b92b4f61e ("PCI/MSI: Remove pci_enable_msi_block_auto()")
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Commit 7b92b4f61e ("PCI/MSI: Remove pci_enable_msi_block_auto()")
introduced a regression: if multiple MSI initialization fails, the code
falls back to INTx rather than to single MSI.
Fixes: 7b92b4f61e ("PCI/MSI: Remove pci_enable_msi_block_auto()")
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
Cc: linux-ide@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Make use of devm_phy_optional_get() in order to fix probe failures on
Armada 370, XP and others, when there is no phy driver available.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
It's a bit odd to see a newer device showing mod15write; however, the
reported behavior is highly consistent and other factors which could
contribute seem to have been verified well enough. Also, both
sata_sil itself and the drive are fairly outdated at this point making
the risk of this change fairly low. It is possible, probably likely,
that other drive models in the same family have the same problem;
however, for now, let's just add the specific model which was tested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: matson <lists-matsonpa@luxsci.me>
References: http://lkml.kernel.org/g/201401211912.s0LJCk7F015058@rs103.luxsci.com
Cc: stable@vger.kernel.org
Without the patch the kernel generates the following error.
ata11.15: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata11.15: Port Multiplier vendor mismatch '0x197b' != '0x123'
ata11.15: PMP revalidation failed (errno=-19)
ata11.15: failed to recover PMP after 5 tries, giving up
This patch helps to bypass this error and the device becomes
functional.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: <linux-ide@vger.kernel.org>
Cc: stable@vger.kernel.org
SATA_MV depends on GENERIC_PHY. So if SATA_MV is built in, GENERIC_PHY
cannot be modular. Fixes build error found by kbuild test robot.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tejun Heo <tj@kernel.org>
clk_prepare_enable() may fail, so let's check its return value and propagate it
in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
- ACPI core changes to make it create a struct acpi_device object for every
device represented in the ACPI tables during all namespace scans regardless
of the current status of that device. In accordance with this, ACPI hotplug
operations will not delete those objects, unless the underlying ACPI tables
go away.
- On top of the above, new sysfs attribute for ACPI device objects allowing
user space to check device status by triggering the execution of _STA for
its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating the
PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the code
"glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for the
DBG2 and PCCT tables to ACPICA, fixes some bugs and improves debug
facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization earlier.
That should allow us to use ACPI during the timekeeping initialization
and possibly to simplify the EFI initialization too. From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over from
Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in drivers
that uses _DSM to execute it via the new helper. From Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun Guo,
Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava, Rashika Kheria,
Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support, from
Dirk Brandewie and intel_pstate documentation from Ramkumar Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John Tobias,
Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC disabled
during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente Kurusa,
Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a cpupower
tool cleanup from One Thousand Gnomes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=dRf6
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"As far as the number of commits goes, the top spot belongs to ACPI
this time with cpufreq in the second position and a handful of PM
core, PNP and cpuidle updates. They are fixes and cleanups mostly, as
usual, with a couple of new features in the mix.
The most visible change is probably that we will create struct
acpi_device objects (visible in sysfs) for all devices represented in
the ACPI tables regardless of their status and there will be a new
sysfs attribute under those objects allowing user space to check that
status via _STA.
Consequently, ACPI device eject or generally hot-removal will not
delete those objects, unless the table containing the corresponding
namespace nodes is unloaded, which is extremely rare. Also ACPI
container hotplug will be handled quite a bit differently and cpufreq
will support CPU boost ("turbo") generically and not only in the
acpi-cpufreq driver.
Specifics:
- ACPI core changes to make it create a struct acpi_device object for
every device represented in the ACPI tables during all namespace
scans regardless of the current status of that device. In
accordance with this, ACPI hotplug operations will not delete those
objects, unless the underlying ACPI tables go away.
- On top of the above, new sysfs attribute for ACPI device objects
allowing user space to check device status by triggering the
execution of _STA for its ACPI object. From Srinivas Pandruvada.
- ACPI core hotplug changes reducing code duplication, integrating
the PCI root hotplug with the core and reworking container hotplug.
- ACPI core simplifications making it use ACPI_COMPANION() in the
code "glueing" ACPI device objects to "physical" devices.
- ACPICA update to upstream version 20131218. This adds support for
the DBG2 and PCCT tables to ACPICA, fixes some bugs and improves
debug facilities. From Bob Moore, Lv Zheng and Betty Dall.
- Init code change to carry out the early ACPI initialization
earlier. That should allow us to use ACPI during the timekeeping
initialization and possibly to simplify the EFI initialization too.
From Chun-Yi Lee.
- Clenups of the inclusions of ACPI headers in many places all over
from Lv Zheng and Rashika Kheria (work in progress).
- New helper for ACPI _DSM execution and rework of the code in
drivers that uses _DSM to execute it via the new helper. From
Jiang Liu.
- New Win8 OSI blacklist entries from Takashi Iwai.
- Assorted ACPI fixes and cleanups from Al Stone, Emil Goode, Hanjun
Guo, Lan Tianyu, Masanari Iida, Oliver Neukum, Prarit Bhargava,
Rashika Kheria, Tang Chen, Zhang Rui.
- intel_pstate driver updates, including proper Baytrail support,
from Dirk Brandewie and intel_pstate documentation from Ramkumar
Ramachandra.
- Generic CPU boost ("turbo") support for cpufreq from Lukasz
Majewski.
- powernow-k6 cpufreq driver fixes from Mikulas Patocka.
- cpufreq core fixes and cleanups from Viresh Kumar, Jane Li, Mark
Brown.
- Assorted cpufreq drivers fixes and cleanups from Anson Huang, John
Tobias, Paul Bolle, Paul Walmsley, Sachin Kamat, Shawn Guo, Viresh
Kumar.
- cpuidle cleanups from Bartlomiej Zolnierkiewicz.
- Support for hibernation APM events from Bin Shi.
- Hibernation fix to avoid bringing up nonboot CPUs with ACPI EC
disabled during thaw transitions from Bjørn Mork.
- PM core fixes and cleanups from Ben Dooks, Leonardo Potenza, Ulf
Hansson.
- PNP subsystem fixes and cleanups from Dmitry Torokhov, Levente
Kurusa, Rashika Kheria.
- New tool for profiling system suspend from Todd E Brandt and a
cpupower tool cleanup from One Thousand Gnomes"
* tag 'pm+acpi-3.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (153 commits)
thermal: exynos: boost: Automatic enable/disable of BOOST feature (at Exynos4412)
cpufreq: exynos4x12: Change L0 driver data to CPUFREQ_BOOST_FREQ
Documentation: cpufreq / boost: Update BOOST documentation
cpufreq: exynos: Extend Exynos cpufreq driver to support boost
cpufreq / boost: Kconfig: Support for software-managed BOOST
acpi-cpufreq: Adjust the code to use the common boost attribute
cpufreq: Add boost frequency support in core
intel_pstate: Add trace point to report internal state.
cpufreq: introduce cpufreq_generic_get() routine
ARM: SA1100: Create dummy clk_get_rate() to avoid build failures
cpufreq: stats: create sysfs entries when cpufreq_stats is a module
cpufreq: stats: free table and remove sysfs entry in a single routine
cpufreq: stats: remove hotplug notifiers
cpufreq: stats: handle cpufreq_unregister_driver() and suspend/resume properly
cpufreq: speedstep: remove unused speedstep_get_state
platform: introduce OF style 'modalias' support for platform bus
PM / tools: new tool for suspend/resume performance optimization
ACPI: fix module autoloading for ACPI enumerated devices
ACPI: add module autoloading support for ACPI enumerated devices
ACPI: fix create_modalias() return value handling
...
Pull libata updates from Tejun Heo:
"Support for some new embedded controllers.
A couple late (<= a week) fixes have stable cc'd and one patch ("SATA:
MV: Add support for the optional PHYs") got committed yesterday
because otherwise the resulting kernel would fail boot on an embedded
board due to interdependent changes in its platform tree.
Other than that, nothing too noteworthy"
* 'for-3.14' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
SATA: MV: Add support for the optional PHYs
sata-highbank: Remove unnecessary ahci_platform.h include
libata: disable LPM for some WD SATA-I devices
ARM: mvebu: update the SATA compatible string for Armada 370/XP
ata: sata_mv: fix disk hotplug for Armada 370/XP SoCs
ata: sata_mv: introduce compatible string "marvell, armada-370-sata"
ata: pata_samsung_cf: Remove unused macros
ata: pata_samsung_cf: Use devm_ioremap_resource()
ata: pata_samsung_cf: Merge pata_samsung_cf.h into pata_samsung_cf.c
ata: pata_samsung_cf: Move plat/regs-ata.h to drivers/ata
drivers: ata: Mark the function as static in libahci.c
drivers: ata: Mark the function ahci_init_interrupts() as static in ahci.c
ahci: imx: fix the error handling in imx_ahci_probe()
ahci: imx: ahci_imx_softreset() can be static
ahci: imx: Add i.MX53 support
ahci: imx: Pull out the clock enable/disable calls
libata, dt: Document sata_rcar bindings
sata_rcar: Add R-Car Gen2 SATA PHY support
ahci: mcp89: enter AHCI mode under Apple BIOS emulation
ata: libata-eh: Remove unnecessary snprintf arithmetic
Some Marvell SoCs have a SATA PHY which can be powered off, in order
to save power. Make use of the generic phy framework to control these
phys.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tejun Heo <tj@kernel.org>
The sata-highbank driver is a complete standalone sata driver, which does
not use ahci_platform.c / ahci_platform_data in any way.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
For some reason, some early WD drives spin up and down drives
erratically when the link is put into slumber mode which can reduce
the life expectancy of the device significantly. Unfortunately, we
don't have full list of devices and given the nature of the issue it'd
be better to err on the side of false positives than the other way
around. Let's disable LPM on all WD devices which match one of the
known problematic model prefixes and are SATA-I.
As horkage list doesn't support matching SATA capabilities, this is
implemented as two horkages - WD_BROKEN_LPM and NOLPM. The former is
set for the known prefixes and sets the latter if the matched device
is SATA-I.
Note that this isn't optimal as this disables all LPM operations and
partial link power state reportedly works fine on these; however, the
way LPM is implemented in libata makes it difficult to precisely map
libata LPM setting to specific link power state. Well, these devices
are already fairly outdated. Let's just disable whole LPM for now.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-tested-by: Nikos Barkas <levelwol@gmail.com>
Reported-and-tested-by: Ioannis Barkas <risc4all@yahoo.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=57211
Cc: stable@vger.kernel.org
A scheduled horkage patch will conflict with HORKAGE changes in
for-3.13-fixes. Pull in to avoid unnecessary merge conflicts.
Signed-off-by: Tejun Heo <tj@kernel.org>
On Armada 370/XP SoCs, once a disk is removed from a SATA port, then the
re-plug events are not detected by the sata_mv driver. This patch fixes
the issue by updating the PHY speed in the LP_PHY_CTL register (0x58)
according to the SControl speed.
Note that this fix is only applied if the compatible string
"marvell,armada-370-sata" is found in the SATA DT node.
Fixes: 9ae6f740b4 ("arm: mach-mvebu: add support for Armada 370 and Armada XP with DT")
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Nadav Haklai <nadavh@marvell.com>
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: stable@vger.kernel.org # v3.6+
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
The sata_mv driver supports the SATA IP found in several Marvell SoCs.
As some new SATA registers have been introduced with the Armada 370/XP
SoCs, a way to identify them is needed.
This patch introduces a new compatible string for the SATA IP found in
Armada 370/XP SoCs.
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Cc: Lior Amsalem <alior@marvell.com>
Cc: stable@vger.kernel.org # v3.6+
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: Tejun Heo <tj@kernel.org>
* acpi-cleanup: (22 commits)
ACPI / tables: Return proper error codes from acpi_table_parse() and fix comment.
ACPI / tables: Check if id is NULL in acpi_table_parse()
ACPI / proc: Include appropriate header file in proc.c
ACPI / EC: Remove unused functions and add prototype declaration in internal.h
ACPI / dock: Include appropriate header file in dock.c
ACPI / PCI: Include appropriate header file in pci_link.c
ACPI / PCI: Include appropriate header file in pci_slot.c
ACPI / EC: Mark the function acpi_ec_add_debugfs() as static in ec_sys.c
ACPI / NVS: Include appropriate header file in nvs.c
ACPI / OSL: Mark the function acpi_table_checksum() as static
ACPI / processor: initialize a variable to silence compiler warning
ACPI / processor: use ACPI_COMPANION() to get ACPI device
ACPI: correct minor typos
ACPI / sleep: Drop redundant acpi_disabled check
ACPI / dock: Drop redundant acpi_disabled check
ACPI / table: Replace '1' with specific error return values
ACPI: remove trailing whitespace
ACPI / IBFT: Fix incorrect <acpi/acpi.h> inclusion in iSCSI boot firmware module
ACPI / i915: Fix incorrect <acpi/acpi.h> inclusions via <linux/acpi_io.h>
SFI / ACPI: Fix warnings reported during builds with W=1
...
Conflicts:
drivers/acpi/nvs.c
drivers/hwmon/asus_atk0110.c
Pull libata fixes from Tejun Heo:
"Late fixes for libata. Nothing too interesting. Adding missing PM
callbacks to satat_sis and an additional PCI ID for ahci"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
sata_sis: missing PM support
ahci: add PCI ID for Marvell 88SE9170 SATA controller
The new pci_msi_vec_count() interface makes pci_enable_msi_block_auto()
superfluous.
Drivers can use pci_msi_vec_count() to learn the maximum number of MSIs
supported by the device, and then call pci_enable_msi_block().
pci_enable_msi_block_auto() was introduced recently, and its only user is
the AHCI driver, which is also updated by this change.
Signed-off-by: Alexander Gordeev <agordeev@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Tejun Heo <tj@kernel.org>
Use devm_ioremap_resource() in order to make the code simpler,
and remove redundant return value check of platform_get_resource()
because the value is checked by devm_ioremap_resource().
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Since pata_samsung_cf.h is referenced only by pata_samsung_cf.c, merge
it into the .c file.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
sata_sis has no suspend/resume methods. The default ones will do fine and
are needed on some systems.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch adds support for the PCI ID provided by the Marvell 88SE9170
SATA controller.
Signed-off-by: Simon Guinot <sguinot@lacie.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: stable@vger.kernel.org
plat/regs-ata.h is used only by Samsung PATA driver.
Move this file to the drivers folder to remove platform
dependency required for multiplatform support.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull libata fixes from Tejun Heo:
"There's one interseting commit - "libata, freezer: avoid block device
removal while system is frozen". It's an ugly hack working around a
deadlock condition between driver core resume and block layer device
removal paths through freezer which was made more reproducible by
writeback being converted to workqueue some releases ago. The bug has
nothing to do with libata but it's just an workaround which is easy to
backport. After discussion, Rafael and I seem to agree that we don't
really need kernel freezables - both kthread and workqueue. There are
few specific workqueues which constitute PM operations and require
freezing, which will be converted to use workqueue_set_max_active()
instead. All other kernel freezer uses are planned to be removed,
followed by the removal of kthread and workqueue freezer support,
hopefully.
Others are device-specific fixes. The most notable is the addition of
NO_NCQ_TRIM which is used to disable queued TRIM commands to Micro
M500 SSDs which otherwise suffers data corruption"
* 'for-3.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata, freezer: avoid block device removal while system is frozen
libata: implement ATA_HORKAGE_NO_NCQ_TRIM and apply it to Micro M500 SSDs
libata: disable a disk via libata.force params
ahci: bail out on ICH6 before using AHCI BAR
ahci: imx: Explicitly clear IMX6Q_GPR13_SATA_MPLL_CLK_EN
libata: add ATA_HORKAGE_BROKEN_FPDMA_AA quirk for Seagate Momentus SpinPoint M8
Scott Carter