According to the datasheet the update bit must be set if the on-time-div
or the base-unit changes.
Now that we properly order device resume on Cherry Trail so that the GFX0
_PS0 method no longer exits with an error, we end up with a sequence of
events where we are writing the same values twice in a row.
First the _PS0 method restores the duty cycle of 0% the GPU driver set
on suspend and then the GPU driver first updates just the enabled bit in
the pwm_state from 0 to 1, causing us to write the same values again,
before restoring the pre-suspend duty-cycle in a separate pwm_apply call.
When writing the update bit the second time, without changing any of
the values the update bit clears immediately / instantly, instead of
staying 1 for a while as usual. After this the next setting of the update
bit seems to be ignored, causing the restoring of the pre-suspend
duty-cycle to not get applied. This makes the backlight come up with
a 0% dutycycle after suspend/resume.
Any further brightness changes after this do work.
This commit moves the setting of the update bit into pwm_lpss_prepare()
and only sets the bit if we have actually changed any of the values.
This avoids the setting of the update bit the second time we configure
the PWM to 0% dutycycle, this fixes the backlight coming up with 0%
duty-cycle after a suspend/resume.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
On Cherry Trail devices under Windows the PWM controller used for the
backlight is considered part of the GPU even though it is part of the LPSS
block and thus is an entirely different independent hardware unit.
Because of this on Cherry Trail the GPU's (GFX0 ACPI node) _PS3 and _PS0
methods save and restore the PWM controller registers.
If userspace blanks the screen before suspending, such as e.g. GNOME
does, then the PWM controller will be runtime-suspended when the suspend
starts. This causes the GFX0 _PS? methods to save a value of 0xffffffff
for the PWM control register and to restore this value on resume.
0xffffffff is not a valid value for the register and writing this causes
problems such as e.g. a flickering backlight.
This commit adds a prepare method to the dev_pm_ops and makes it return 0
on Cherry Trail devices forcing a runtime-resume before other device's
suspend methods run. This fixes the reading and writing back of 0xffffffff.
Since we now always runtime-resume the device on suspend, it will be
resumed on resume too and we no longer need to check for the GFX0 _PS0
method having resumed it underneath us, so this commit removes the now no
longer necessary complete dev_pm_op.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
K3 devices have the same ECAP IP as OMAP SoCs. Enable driver to be built
for K3 devices. Also, drop reference to AM33xx in help text, as IP is
found on multiple TI SoCs.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patch sends a uevent (KOBJ_CHANGE) on the pwmchipN device,
everytime a pwmX channel has been exported/unexported via sysfs. This
allows udev to implement rules on such events, like:
SUBSYSTEM=="pwm*", PROGRAM="/bin/sh -c '\
chown -R root:gpio /sys/class/pwm && chmod -R 770 /sys/class/pwm;\
chown -R root:gpio
/sys/devices/platform/soc/*.pwm/pwm/pwmchip* && chmod -R 770
/sys/devices/platform/soc/*.pwm/pwm/pwmchip*\
'"
This is a replacement patch for commit 7e5d1fd75c ("pwm: Set class for
exported channels in sysfs"), see [1].
basic testing:
$ udevadm monitor --environment &
$ echo 0 > /sys/class/pwm/pwmchip0/export
KERNEL[197.321736] change /devices/.../pwm/pwmchip0 (pwm)
ACTION=change
DEVPATH=/devices/.../pwm/pwmchip0
EXPORT=pwm0
SEQNUM=2045
SUBSYSTEM=pwm
[1] https://lkml.org/lkml/2018/9/25/713
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Tested-by: Gottfried Haider <gottfried.haider@gmail.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This reverts commit 7e5d1fd75c ("pwm: Set
class for exported channels in sysfs") as it causes regression with
multiple pwm chip[1], when exporting a pwm channel (echo X > export):
- ABI (Documentation/ABI/testing/sysfs-class-pwm) states pwmX should be
created in /sys/class/pwm/pwmchipN/pwmX
- Reverted patch causes new entry to be also created directly in
/sys/class/pwm/pwmX
- 1st time, exporting pwmX will create an entry in /sys/class/pwm/pwmX
- class attributes are added under pwmX folder, such as export, unexport
npwm, symlinks. This is wrong as it belongs to pwmchipN. It may cause
bad behavior and report wrong values.
- when another export happens on another pwmchip, it can't be created
(e.g. -EEXIST). This is causing the issue with multiple pwmchip.
Example on stm32 (stm32429i-eval) platform:
$ ls /sys/class/pwm
pwmchip0 pwmchip4
$ cd /sys/class/pwm/pwmchip0/
$ echo 0 > export
$ ls /sys/class/pwm
pwm0 pwmchip0 pwmchip4
$ cd /sys/class/pwm/pwmchip4/
$ echo 0 > export
sysfs: cannot create duplicate filename '/class/pwm/pwm0'
...Exception stack follows...
This is also seen on other platform [2]
[1] https://lkml.org/lkml/2018/9/25/713
[2] https://lkml.org/lkml/2018/9/25/447
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Tested-by: Gottfried Haider <gottfried.haider@gmail.com>
Tested-by: Michal Vokáč <michal.vokac@ysoft.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add a get_state callback so that the initial state correctly reflects
the actual hardware state.
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
For each pwm output which gets enabled through pwm_lpss_apply(), we do a
pm_runtime_get_sync().
This commit adds pm_runtime_put() calls to pwm_lpss_remove() to balance
these when the driver gets removed with some of the outputs still enabled.
Fixes: f080be27d7 ("pwm: lpss: Add support for runtime PM")
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The _PS0 method for the integrated graphics on some Cherry Trail devices
(observed on a HP Pavilion X2 10-p0XX) turns on the PWM chip (puts it in
D0), causing an inconsistency between the state the pm-core thinks it is
in (left runtime suspended as it was before the suspend/resume) and the
state it actually is in.
Interestingly enough this is done on a device where the pwm controller is
not used for the backlight at all, since it uses an eDP panel. On devices
where the PWM is used this is not a problem since we will resume it
ourselves anyways.
This inconsistency causes us to never suspend the pwm controller again,
which causes the device to not be able to reach S0ix states when suspended.
This commit adds a resume-complete handler, which when we think the device
is still run-time suspended checks the actual power-state and if necessary
updates the rpm-core's internal state.
This fixes the Pavilion X2 10-p0XX not reaching S0ix states when suspended.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Move struct pwm_lpss_chip definition from pwm-lpss.c to pwm-lpss.h,
so that the pci/platform drivers can access the info member
(struct pwm_lpss_boardinfo *).
This is a preparation patch for adding platform specific quirks, which
the drivers need access to, to pwm_lpss_boardinfo.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The second PWM controller on Cherry Trail devices uses a separate ACPI
HID: "80862289", add this so that the driver will properly bind to the
second PWM controller.
The second PWM controller is usually not used, the main thing gained by
this is properly putting the PWM controller in D3 on suspend.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
It's common to follow a device tree ID table by the MODULE_DEVICE_TABLE
immediately, without an extra blank line between.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add support for MT7628. The SoC is legacy MIPS and hence has no complex
clock tree. This patch add an extra flag to the SoC specific data
indicating, that no clocks are present.
Signed-off-by: John Crispin <john@phrozen.org>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Current clock name looks like this:
/soc/bus@ffd00000/pwm@1b000#mux0
This is bad because CCF uses the clock to create a directory in clk debugfs.
With such name, the directory creation (silently) fails and the debugfs
entry end up being created at the debugfs root.
With this change, the clock name will now be:
ffd1b000.pwm#mux0
This matches the clock naming scheme used in the ethernet and mmc driver.
It also fixes the problem with debugfs.
Fixes: 36af66a790 ("pwm: Convert to using %pOF instead of full_name")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
LPTimer has only one pwm channel (npwm = 1). Remove useless for loop
in remove routine.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
If a pwm-omap-dmtimer is probed before the dmtimer it uses, the platform
data won't be set yet.
Fixes: ac30751df9 ("ARM: OMAP: pdata-quirks: Remove unused timer pdata")
Cc: <stable@vger.kernel.org> # 4.17+
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Ladislav Michl <ladis@linux-mips.org>
Tested-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Enabled the support for the new SoC i.MX8QM by adding the compatible
string of "fsl,imx8qm-ftm-pwm" and its per-compatible data with setting
"has_enable_bits" to "true".
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
On the i.MX8x SoC family, an additional PWM enable bit is added for each
PWM channel in the register FTM_SC[23:16]. It supports 8 channels. Bit
16 is for channel 0, and bit 23 is for channel 7. As the IP version
information can not be obtained via any of the FTM registers, a property
of "has_enable_bits" is added via per-compatible data structure.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The current driver assumes that the ftm_sys clock works as one of the
clock sources for the IP block as well as the IP interface clock. This
assumption does not apply any more on the latest i.MX8x SoC family. On
i.MX8x SoCs, a dedicated IP interface clock is introduced and it must be
enabled before accessing any FTM registers. Moreover, the clock can not
be used as the source clock for the FTM IP block. This patch introduces
the ipg_clk as the dedicated IP interface clock and by default it is the
same as the ftm_sys clock if not specified.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
pwm-tiehrpwm driver disables PWM output by putting it in low output
state via active AQCSFRC register in ehrpwm_pwm_disable(). But, the
AQCSFRC shadow register is not updated. Therefore, when shadow AQCSFRC
register is re-enabled in ehrpwm_pwm_enable() (say to enable second PWM
output), previous settings are lost as shadow register value is loaded
into active register. This results in things like PWMA getting enabled
automatically, when PWMB is enabled and vice versa. Fix this by
updating AQCSFRC shadow register as well during ehrpwm_pwm_disable().
Fixes: 19891b20e7 ("pwm: pwm-tiehrpwm: PWM driver support for EHRPWM")
Cc: stable@vger.kernel.org
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
As per AM335x TRM SPRUH73P "15.2.2.11 ePWM Behavior During Emulation",
TBCTL[15:14] only have effect during emulation suspend events (IOW,
to stop PWM when debugging using a debugger). These bits have no effect
on PWM output during normal running of system. Hence, remove code
accessing these bits as they have no role in enabling/disabling PWMs.
Fixes: 19891b20e7 ("pwm: pwm-tiehrpwm: PWM driver support for EHRPWM")
Cc: stable@vger.kernel.org
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The Berlin PWM driver is currently broken on at least BG2CD. The
symptoms manifest as a very non-linear and erratic mapping from the duty
cycle configured in software to the duty cycle produced by hardware.
The cause of the bug is software's configuration of the prescaler, and
in particular its usage of the six prescaler values between the minimum
value of 1 and the maximum value of 4096. As it turns out, these six
values do not actually slow down the PWM clock; rather, they emulate
slowing down the clock by internally multiplying the value of TCNT.
This would be a fine trick, if not for the fact that the internal,
scaled TCNT value has no extra bits beyond the 16 already exposed to
software in the register. What this means is that, for a prescaler of 4,
the software must ensure that the top two bits of TCNT are not set,
because hardware will chop them off; for a prescaler of 8, the top three
bits must not be set, and so forth. Software does not currently ensure
this, resulting in a TCNT several orders of magnitude lower than
intended any time one of those six prescalers are selected.
Because hardware chops off the high bits in its internal shift, the
middle six prescalers don't actually allow *anything* that the first
doesn't. In fact, they are strictly worse than the first, since the
internal shift of TCNT prevents software from setting the low bits,
decreasing the resolution, without providing any extra high bits.
By skipping the useless prescalers entirely, this patch both fixes the
driver's behavior and increases its performance (since, when the 4096
prescaler is selected, it now does only a single shift rather than the
seven successive divisions it did before).
Tested on BG2CD.
Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This contains a couple of fixes and cleanups for the Meson and ACPI/LPSS
drivers as well as capture support for STM32. Note that given the cross-
subsystem changes, the STM32 patches were merged through the MFD and PWM
trees, both sharing an immutable branch.
-----BEGIN PGP SIGNATURE-----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=ZED5
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This contains a couple of fixes and cleanups for the Meson and
ACPI/LPSS drivers as well as capture support for STM32.
Note that given the cross- subsystem changes, the STM32 patches were
merged through the MFD and PWM trees, both sharing an immutable
branch"
* tag 'pwm/for-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: stm32: Fix build warning with CONFIG_DMA_ENGINE disabled
pwm: stm32: Enforce dependency on CONFIG_MFD_STM32_TIMERS
ACPI / LPSS: Add missing prv_offset setting for byt/cht PWM devices
pwm: lpss: platform: Save/restore the ctrl register over a suspend/resume
dt-bindings: mfd: stm32-timers: Add support for dmas
pwm: simplify getting .drvdata
pwm: meson: Fix allocation of PWM channel array
Without dmaengine support, we get a harmless warning about an unused
function:
drivers/pwm/pwm-stm32.c:166:12: error: 'stm32_pwm_capture' defined but not used [-Werror=unused-function]
Changing the #ifdef to an IS_ENABLED() check shuts up that warning and
is slightly nicer to read.
Fixes: 53e38fe73f ("pwm: stm32: Add capture support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
-----BEGIN PGP SIGNATURE-----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=e4zs
-----END PGP SIGNATURE-----
Merge tag 'ib-mfd-pwm-v4.18-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into for-next
Immutable branch between MFD and PWM due for the v4.18 merge window (v2)
When compile-testing the PWM driver without also enabling the
stm32_timers MFD, we run into a link error:
drivers/pwm/pwm-stm32.o: In function `stm32_pwm_raw_capture.isra.6':
pwm-stm32.c:(.text+0xcb0): undefined reference to `stm32_timers_dma_burst_read'
We don't need the '|| COMPILE_TEST' here, since stm32_timers itself
can be built with CONFIG_COMPILE_TEST on all architectures, so we do
get the coverage through allmodconfig and randconfig builds even
when we make it a hard dependency.
Fixes: 7edf736920 ("pwm: Add driver for STM32 plaftorm")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
On some devices the contents of the ctrl register get lost over a
suspend/resume and the PWM comes back up disabled after the resume.
This is seen on some Bay Trail devices with the PWM in ACPI enumerated
mode, so it shows up as a platform device instead of a PCI device.
If we still think it is enabled and then try to change the duty-cycle
after this, we end up with a "PWM_SW_UPDATE was not cleared" error and
the PWM is stuck in that state from then on.
This commit adds suspend and resume pm callbacks to the pwm-lpss-platform
code, which save/restore the ctrl register over a suspend/resume, fixing
this.
Note that:
1) There is no need to do this over a runtime suspend, since we
only runtime suspend when disabled and then we properly set the enable
bit and reprogram the timings when we re-enable the PWM.
2) This may be happening on more systems then we realize, but has been
covered up sofar by a bug in the acpi-lpss.c code which was save/restoring
the regular device registers instead of the lpss private registers due to
lpss_device_desc.prv_offset not being set. This is fixed by a later patch
in this series.
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This removes build warning when COMPILE_TEST=y and MFD_STM32_TIMERS=n
in drivers/pwm/pwm-stm32.c. In function 'stm32_pwm_capture' 'raw_prd' and
'raw_dty' may be used uninitialized in this function
[-Wmaybe-uninitialized]
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Using input prescaler, capture unit will trigger DMA once every
configurable /2, /4 or /8 events (rising edge). This helps improve
period (only) capture accuracy at high rates.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Currently, capture is based on timeout window to configure prescaler.
PWM capture framework provides 1s window at the time of writing.
There's place for improvement, after input signal has been captured once:
- Finer tune counter clock prescaler, by using 1st capture result (with
arbitrary margin).
- Do a 2nd capture, with scaled capture window.
This increases accuracy, especially at high rates.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Add support for PMW input mode on pwm-stm32. STM32 timers support
period and duty cycle capture as long as they have at least two PWM
channels. One capture channel is used for period (rising-edge), one
for duty-cycle (falling-edge).
When there's only one channel available, only period can be captured.
Duty-cycle is simply zero'ed in such a case.
Capture requires exclusive access (e.g. no pwm output running at the
same time, to protect common prescaler).
Timer DMA burst mode (from MFD core) is being used, to take two
snapshots of capture registers (upon each period rising edge).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
We should get drvdata from struct device directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Using the pwm-meson driver on the 32-bit SoCs causes memory corruption.
The result are some hard-to-explain errors, for example
devm_clk_register() crashes with a NULL dereference somewhere deep in
the common clock framework code. In some cases the kernel even refused
to boot when any of the PWM controllers were enabled on Meson8b.
The root cause is an incorrect memory size in the devm_kcalloc() call in
meson_pwm_probe(). The code allocates an array of meson_pwm_channel
structs, but the size given is the size of the meson_pwm struct (which
seems like a small copy-and-paste error, as meson_pwm is allocated a few
lines above).
Even with this typo the code seemed to work fine on the 64-bit GX SoCs
(maybe due to the structs having the same size in the compiled result,
but I haven't checked this further).
Fixes: 211ed63075 ("pwm: Add support for Meson PWM Controller")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This set of changes adds support for more generations of the RCar
controller as well as runtime PM support. The JZ4740 driver gains
support for device tree and can now be used on all Ingenic SoCs.
Rounding things off is a random assortment of fixes and cleanups
all across the board.
-----BEGIN PGP SIGNATURE-----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=JiRM
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set of changes adds support for more generations of the RCar
controller as well as runtime PM support. The JZ4740 driver gains
support for device tree and can now be used on all Ingenic SoCs.
Rounding things off is a random assortment of fixes and cleanups all
across the board"
* tag 'pwm/for-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (29 commits)
pwm: rcar: Add suspend/resume support
pwm: rcar: Use PM Runtime to control module clock
dt-bindings: pwm: rcar: Add bindings for R-Car M3N support
pwm: rcar: Fix a condition to prevent mismatch value setting to duty
pwm: sysfs: Use put_device() instead of kfree()
dt-bindings: pwm: sunxi: Add new compatible strings
pwm: sun4i: Simplify controller mapping
pwm: sun4i: Drop unused .has_rdy member
pwm: sun4i: Properly check current state
pwm: Remove depends on AVR32
pwm: stm32: LPTimer: Use 3 cells ->of_xlate()
dt-bindings: pwm-stm32-lp: Add #pwm-cells
pwm: stm32: Protect common prescaler for all channels
pwm: stm32: Remove unused struct device
pwm: mediatek: Improve precision in rate calculation
pwm: mediatek: Remove redundant MODULE_ALIAS entries
pwm: mediatek: Fix up PWM4 and PWM5 malfunction on MT7623
pwm: jz4740: Enable for all Ingenic SoCs
pwm: jz4740: Add support for devicetree
pwm: jz4740: Implement ->set_polarity()
...
This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips
in mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older
PXA and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure
is needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=HD9V
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"This release brings up a new platform based on the old ARM9 core: the
Nuvoton NPCM is used as a baseboard management controller, competing
with the better known ASpeed AST2xx series.
Another important change is the addition of ARMv7-A based chips in
mach-stm32. The older parts in this platform are ARMv7-M based
microcontrollers, now they are expanding to general-purpose workloads.
The other changes are the usual defconfig updates to enable additional
drivers, lesser bugfixes. The largest updates as often are the ongoing
OMAP cleanups, but we also have a number of changes for the older PXA
and davinci platforms this time.
For the Renesas shmobile/r-car platform, some new infrastructure is
needed to make the watchdog work correctly.
Supporting Multiprocessing on Allwinner A80 required a significant
amount of new code, but is not doing anything unexpected"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (179 commits)
arm: npcm: modify configuration for the NPCM7xx BMC.
MAINTAINERS: update entry for ARM/berlin
ARM: omap2: fix am43xx build without L2X0
ARM: davinci: da8xx: simplify CFGCHIP regmap_config
ARM: davinci: da8xx: fix oops in USB PHY driver due to stack allocated platform_data
ARM: multi_v7_defconfig: add NXP FlexCAN IP support
ARM: multi_v7_defconfig: enable thermal driver for i.MX devices
ARM: multi_v7_defconfig: add RN5T618 PMIC family support
ARM: multi_v7_defconfig: add NXP graphics drivers
ARM: multi_v7_defconfig: add GPMI NAND controller support
ARM: multi_v7_defconfig: add OCOTP driver for NXP SoCs
ARM: multi_v7_defconfig: configure I2C driver built-in
arm64: defconfig: add CONFIG_UNIPHIER_THERMAL and CONFIG_SNI_AVE
ARM: imx: fix imx6sll-only build
ARM: imx: select ARM_CPU_SUSPEND for CPU_IDLE as well
ARM: mxs_defconfig: Re-sync defconfig
ARM: imx_v4_v5_defconfig: Use the generic fsl-asoc-card driver
ARM: imx_v4_v5_defconfig: Re-sync defconfig
arm64: defconfig: enable stmmac ethernet to defconfig
ARM: EXYNOS: Simplify code in coupled CPU idle hot path
...
Runtime PM API (pm_runtime_get_sync/pm_runtime_put) should be used
to control module clock instead of clk_prepare_enable and
clk_disable_unprepare.
Signed-off-by: Hien Dang <hien.dang.eb@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patch fixes an issue that is possible to set mismatch value to duty
for R-Car PWM if we input the following commands:
# cd /sys/class/pwm/<pwmchip>/
# echo 0 > export
# cd pwm0
# echo 30 > period
# echo 30 > duty_cycle
# echo 0 > duty_cycle
# cat duty_cycle
0
# echo 1 > enable
--> Then, the actual duty_cycle is 30, not 0.
So, this patch adds a condition into rcar_pwm_config() to fix this
issue.
Signed-off-by: Ryo Kodama <ryo.kodama.vz@renesas.com>
[shimoda: revise the commit log and add Fixes and Cc tags]
Fixes: ed6c1476bf ("pwm: Add support for R-Car PWM Timer")
Cc: Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Never directly free @dev after calling device_register(), even if it
returned an error! Always use put_device() to give up the reference
initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
At the moment we assign our supported compatible strings to a respective
instance of our sun4i_pwm_data structure, even though some of them
are the same.
To avoid further clutter, split out the three different combinations of
features we have at the moment and name them accordingly.
This should make it more obvious which compatible string to use for new
SoCs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Commit a054c4d684 ("pwm: sun4i: Drop legacy callbacks") dropped the
only user of the .has_rdy member in our sun4i_pwm_data struct.
Consequently we don't need to store this anymore for the various SoCs,
which paves the way for further simplifications.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Correctly extract the prescaler value from CTRL_REG before comparing it
to PWM_PRESCAL_MASK.
Also, check that both PWM_CLK_GATING and PWM_EN to ensure the PWM is
enabled instead of relying on only one of those.
Fixes: 93e0dfb2c5 ("pwm: sun4i: Improve hardware read out")
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
AVR32 is gone, so no more need to depend on it.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There may be a race, when configuring two PWM channels, with different
prescaler values, when there's no active channel yet.
Add mutex lock to avoid concurrent access on PWM apply state.
This is also precursor patch for PWM capture support.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
dev is never assigned or used. Remove it.
Fixes: 7edf736920 ("pwm: Add driver for STM32 plaftorm")
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Benjamin Gaignard <benjamin.gaignard@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add a way that turning resolution from in nanosecond into in picosecond
to improve noticeably almost 4.5% precision.
It's necessary to hold the new resolution with type u64 and thus related
operations on u64 are applied instead in those rate calculations.
And the patch has a dependency on [1].
[1] http://lists.infradead.org/pipermail/linux-mediatek/2018-March/012225.html
Cc: stable@vger.kernel.org
Fixes: caf065f8fd ("pwm: Add MediaTek PWM support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
MODULE_ALIAS exports information to allow the module to be auto-loaded at
boot for the drivers registered using legacy platform registration.
However, currently the driver is always used by DT-only platform,
MODULE_ALIAS is redundant and should be removed properly.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Since the offset for both registers, PWMDWIDTH and PWMTHRES, used to
control PWM4 or PWM5 are distinct from the other PWMs, whose wrong
programming on PWM hardware causes waveform cannot be output as expected.
Thus, the patch adds the extra condition for fixing up the weird case to
let PWM4 or PWM5 able to work on MT7623.
v1 -> v2: use pwm45_fixup naming instead of pwm45_quirk
v2 -> v3: add more tags for Reviewed-by, Fixes, and Cc stable
Cc: stable@vger.kernel.org
Fixes: caf065f8fd ("pwm: Add MediaTek PWM support")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Zhi Mao <zhi.mao@mediatek.com>
Cc: John Crispin <john@phrozen.org>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This driver works perfectly with all the versions of the SoCs from
Ingenic that are supported upstream.
This makes the driver usable on JZ4740, JZ4770 and JZ4780 SoCs.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add support for probing the pwm-jz4740 directly from devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This permits clients of this driver to specify the polarity to use for
their PWM channel.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
On the JZ4750 and later SoCs, channel 1 and 2 operate in a different
way (TCU2 mode) as the other channels. If a TCU2 mode counter is
stopped before its PWM functionality is disabled, the output is not
guaranteed to return to the initial level.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
On a imx6q-cubox-i board, which has an LED driven by PWM, when the system
goes into suspend the PWM block is disabled by default, then the PWM pin
goes to logic level zero and turn on the LED during suspend, which is not
really the behaviour we want to see.
By keeping the PWM enabled during suspend via STOPEN bit, the pwm-leds
driver sets the brightness to zero in suspend and then the LED is
turned off as expected.
So always set the STOPEN to fix the PWM behaviour in suspend.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add SPDX identifier to make it easier to determine the license of the
file.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Acked-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The blackfin architecture is getting removed, so this driver is now
obsolete as well.
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A lot of Kconfig symbols have architecture specific dependencies.
In those cases that depend on architectures we have already removed,
they can be omitted.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
For PWM controller in the Meson-AXG SoC, the EE domain and AO domain
have different clock sources. This patch tries to describe them in the
DT compatible data.
Signed-off-by: Jian Hu <jian.hu@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Notifications for devices without bus or class set get dropped by
dev_uevent_filter(). Adding the class to the exported child matches
what the GPIO subsystem is doing.
With this change exporting a channel triggers a udev event, which
gives userspace a chance to fixup permissions and makes it possible
for non-root users to make use of the PWM subsystem.
Signed-off-by: Gottfried Haider <gottfried.haider@gmail.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: H Hartley Sweeten <hsweeten@visionengravers.com>
CC: linux-pwm@vger.kernel.org
CC: linux-arm-kernel@lists.infradead.org
CC: linux-rpi-kernel@lists.infradead.org
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The changes for this release include power management improvements for
the pwm-img driver, support for the backup mode on pwm-atmel-tcb as well
as support for more hardware with the R-Car and Mediatek drivers.
To round things off there's a bit of cleanup for sunxi and stm32-lp.
-----BEGIN PGP SIGNATURE-----
iQJNBAABCAA3FiEEiOrDCAFJzPfAjcif3SOs138+s6EFAloVVScZHHRoaWVycnku
cmVkaW5nQGdtYWlsLmNvbQAKCRDdI6zXfz6zoYitD/9e9MWl5VW4Bz6FHfh1uKNB
cwdgTHj4JE/7LA/p2hP7Zzs5xx1Blyf3TDjr2LFB/C6tWVRfve8TN6y4L3Md6Rv/
gdV2Sy9Hg02kMCiLyPihpFKx4aMoiiB3g0nygG5pC/etX6PB+mmH4XocnjpuHOGf
s1f2JULEm2C1nfYqzmhGBTiiwSOAPMfPdhvGvS2ydrW5HoCYJ+tK3hnWXBJjYUyk
R5zHr7blqT5f7FzA9Rx+5UY5vQlISwUfvdi/EHT7ighgF/dggaBWKuK+R0sCEhq1
AdyrgEEJsXeh9XcCdfKveEJKu8I6zROYeBfrxeZr2Kzl2mTx6a3U0vviI0hLZSPh
IrLyo3MnIVcTuZyII07jjM9KePnOYuDjjMc9qDP5QrNJHZI66Qf0f3wzg1QIIW5D
+3LXFnlWH59fHwvb80vpSVgI0S9T76W2tLqQfM/pKdOiwYs+A10cQvTwvUHMTerl
zHJ4DdEugLoZzJaZto29ilP7DygMjmDkFPh4z9f92d94JskXFfsEU3oSclggMXFy
2xzAm5bNwLibBgwThXUVmP/rR3AFQXDGvjPPK1DIhQxjJb6gjgQNLOvPfgN+kx65
kjc20jEpJxpnXk7y6kecLEEdxO/o/GdysfGfdk/BlOsBMV/BmVX0igpaal9fOqQp
34P+xRbpnmuKU4E8TpT43w==
=HLrm
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The changes for this release include power management improvements for
the pwm-img driver, support for the backup mode on pwm-atmel-tcb as
well as support for more hardware with the R-Car and Mediatek drivers.
To round things off there's a bit of cleanup for sunxi and stm32-lp"
* tag 'pwm/for-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: stm32-lp: Remove pwm_is_enabled() check before calling pwm_disable()
pwm: mediatek: Add MT2712/MT7622 support
pwm: sunxi: Use of_device_get_match_data()
pwm: atmel-tcb: Support backup mode
dt-bindings: pwm: Add R-Car D3 device tree bindings
pwm: img: Add runtime PM
pwm: img: Add suspend / resume handling
The same checking is done by the implementation of pwm_disable().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add support for MT2712 and MT7622. Due to register offset address of
pwm7 for MT2712 is not fixed 0x40, add mtk_pwm_reg_offset array for PWM
register offset.
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The usage of of_device_get_match_data reduce the code size a bit.
Furthermore, it prevents an improbable dereference when
of_match_device() returns NULL.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Save and restore registers for the PWM on suspend and resume, which
makes hibernation and backup modes possible.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Add runtime PM to disable the clocks when the h/w is not in use.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The power may be disabled during suspend, so implement suspend and
resume callbacks to save and restore register state.
Signed-off-by: Ed Blake <ed.blake@sondrel.com>
[thierry.reding@gmail.com: guard using PM_SLEEP instead of PM]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The changes for this release include a new driver for the PWM controller
found on SoCs of the ZTX ZX family. Support for an old SH-Mobile SoC has
been dropped and the Rockchip and MediaTek drivers gain support for more
generations.
Other than that there are a bunch of coding style fixes, minor bug fixes
and cleanup as well as documentation patches.
-----BEGIN PGP SIGNATURE-----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=GUps
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"The changes for this release include a new driver for the PWM
controller found on SoCs of the ZTX ZX family. Support for an old
SH-Mobile SoC has been dropped and the Rockchip and MediaTek drivers
gain support for more generations.
Other than that there are a bunch of coding style fixes, minor bug
fixes and cleanup as well as documentation patches"
* tag 'pwm/for-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (32 commits)
pwm: pwm-samsung: fix suspend/resume support
pwm: samsung: Remove redundant checks from pwm_samsung_config()
pwm: mediatek: Disable clock on PWM configuration failure
dt-bindings: pwm: Add MT2712/MT7622 information
pwm: mediatek: Fix clock control issue
pwm: mediatek: Fix PWM source clock selection
pwm: mediatek: Fix Kconfig description
pwm: tegra: Explicitly request exclusive reset control
pwm: hibvt: Explicitly request exclusive reset control
pwm: tiehrpwm: Set driver data before runtime PM enable
pwm: tiehrpwm: Miscellaneous coding style fixups
pwm: tiecap: Set driver data before runtime PM enable
pwm: tiecap: Miscellaneous coding style fixups
dt-bindings: pwm: tiecap: Add TI 66AK2G SoC specific compatible
pwm: tiehrpwm: fix clock imbalance in probe error path
pwm: tiehrpwm: Fix runtime PM imbalance at unbind
pwm: Kconfig: Enable pwm-tiecap to be built for Keystone
pwm: Add ZTE ZX PWM device driver
dt-bindings: pwm: Add bindings doc for ZTE ZX PWM controller
pwm: bcm2835: Support for polarity setting via DT
...
Add support for single PWM channel on Low-Power Timer, that can be
found on some STM32 platforms.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Fix suspend/resume support:
- add disabled_mask to struct samsung_pwm_chip to track PWM
disabled state information in pwm_samsung_{disable,enable}()
- rename pwm_samsung_config() to __pwm_samsung_config() and
add extra force_period parameter to be used during resume
(to force tin_ns and tcnt recalculation)
- add pwm_samsung_config() wrapper for preserving old behavior
- properly restore PWM configuration in pwm_samsung_resume()
- remove no longer needed pwm_samsung_suspend()
- update Copyrights
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
If the requested period_ns and duty_ns values are identical to the last
programmed ones pwm_samsung_config() returns early and skips the
hardware configuration. The same checks are now done by the PWM core so
the driver specific ones can be removed.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Make sure to disable the PWM clock if the PWM cannot be configured due
to the clock divider exceeding the maximum value.
While at it, replace the hardcoded maximum clock divider with a defined
constant to improve code readability.
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In order to save some power, do not prepare the top and main clocks
during mtk_pwm_probe(). Instead, prepare the clocks only when necessary
and also make sure to enable the clocks to match the semantics of the
common clock framework.
While at it, don't explicitly disable all PWM channels in ->remove()
because all users should have done that already.
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In original code, the PWM output frequency is not correct when set
bit<3>=1 to PWMCON register.
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Fix a copy/paste error that sneaked into the Kconfig description of the
Mediatek PWM driver.
Signed-off-by: Zhi Mao <zhi.mao@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: linux-pwm@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Commit a53e35db70 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-pwm@vger.kernel.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Runtime PM callbacks can be run right after runtime PM is enabled, so
make sure to set the driver data before that. This is unlikely to ever
happen with the current driver, but it doesn't hurt to follow best
practices anyway.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
I noticed most of these while reviewing another patch and thought I'd
fix them while at it. These are mostly changes to make variable types
more strict and whitespace fixups.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Runtime PM callbacks can be run right after runtime PM is enabled, so
make sure to set the driver data before that. This is unlikely to ever
happen with the current driver, but it doesn't hurt to follow best
practices anyway.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
I noticed most of these while reviewing another patch and thought I'd
fix them while at it. These are mostly changes to make variable types
more strict and whitespace fixups.
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Make sure to unprepare the clock before returning on late probe errors.
Fixes: b388f15fd1 ("pwm: pwm-tiehrpwm: Use clk_enable/disable instead clk_prepare/unprepare.")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Remove unbalanced RPM put at driver unbind which resulted in a negative
usage count.
Fixes: 19891b20e7 ("pwm: pwm-tiehrpwm: PWM driver support for EHRPWM")
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
66AK2G SoC has ECAP subsystem that is used as pwm-backlight provider for
display. Hence, enable pwm-tiecap driver to be built for Keystone
architecture.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
It adds PWM device driver for ZTE ZX family SoCs. The PWM controller
supports 4 devices with polarity configuration.
The driver has been tested with pwm-regulator support to scale core
voltage via cpufreq.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This adds support for the third (optional) pwm cell to specify the
polarity, which is needed by display backlights for example.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The rk3328 SoC supports atomic update, we could lock the configuration
of period and duty at first, after unlock is configured, the period and
duty are effective at the same time.
If the polarity, period and duty need to be configured together,
the way for atomic update is "configure lock and old polarity" ->
"configure period and duty" -> "configure unlock and new polarity".
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Just use the same PWM ops for each IP, and get rid of the ops in struct
rockchip_pwm_data, but still define the three different instances of the
struct to use common interface for each IP.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
It is usually possible to configure the polarity, cycle and duty all at
once, so that the polarity and cycle and duty are applied atomically.
Move it from rockchip_pwm_set_enable() into rockchip_pwm_config(), as
well as prepare for the next atomic update commit.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Drop the custom hook of pwm_enable() and implement pwm_apply_v1() and
pwm_apply_v2() instead.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
It seems the rockchip_pwm_config() always returns the result 0, so
remove the judge.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
New PWM module provides two individual clocks for APB clock and function
clock.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Remove support for the SH7372 (SH-Mobile AP4) from the renesas-tpu
driver.
Commit edf4100906 ("ARM: shmobile: sh7372 dtsi: Remove Legacy
file") removed this SoC from the kernel in v4.1.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Undo preparation of a clock source if vt8500_pwm_probe() is not
successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The function
static void pca9685_set_sleep_mode(struct pca9685 *pca, int sleep)
takes the chip in and out of sleep mode, depending on the value of
sleep, which is interpreted as a boolean.
To clarify that 'int sleep' is a boolean and not a sleep delay,
change the function interface to:
static void pca9685_set_sleep_mode(struct pca9685 *pca, bool enable)
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sven Van Asbroeck <thesven73@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Carlo Caione <carlo@caione.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: linux-pwm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-amlogic@lists.infradead.org
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This release cycle's changes include mostly updates and cleanups to
existing drivers along with a few cleanups to the core, documentation
and device tree bindings.
-----BEGIN PGP SIGNATURE-----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=ioFX
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This release cycle's changes include mostly updates and cleanups to
existing drivers along with a few cleanups to the core, documentation
and device tree bindings"
* tag 'pwm/for-4.13-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: cros-ec: Fix transposed param settings
pwm: meson: Improve PWM calculation precision
dt-bindings: pwm: meson: Add compatible for gxbb ao PWMs
pwm: meson: Add compatible for the gxbb ao PWMs
pwm: sun4i: Drop legacy callbacks
pwm: sun4i: Switch to atomic PWM
pwm: sun4i: Improve hardware read out
pwm: hibvt: Constify hibvt_pwm_ops
pwm: Silently error out on EPROBE_DEFER
pwm: Standardize document format
pwm: bfin: Remove unneeded error message
dt-bindings: pwm: Update STM32 timers clock names
dt-bindings: pwm: Add R-Car M3-W device tree bindings
pwm: tegra: Set maximum pwm clock source per SoC tapeout
The __cros_ec_pwm_get_duty() routine was transposing the insize and
outsize fields when calling cros_ec_cmd_xfer_status().
The original code worked without error due to size of the two particular
parameter blocks passed to cros_ec_cmd_xfer_status(), so this change is
not fixing an actual runtime problem, just correcting the calling usage.
Signed-off-by: Nick Vaccaro <nvaccaro@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
When using input clocks with high rates, such as clk81 (166MHz), the
fin_ns = NSEC_PER_SEC / fin_freq can introduce a significant error.
Ex: fin_freq = 166666667, NSEC_PER_SEC = 1000000000
fin_ns = 5,9999999
which is, of course, rounded down to 5. This introduces an error of ~20%
on the period requested from the PWM.
This patch uses ps instead of ns (and 64 bit integers) to perform the
calculation. This should give a good enough precision.
Fixes: 211ed63075 ("pwm: Add support for Meson PWM Controller")
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
squash! pwm: meson: Improve pwm calculation precision
On the gxbb (and gxl) family, the PWMs of the AO domain require a
specific compatible because the possible input clocks are different
from the EE PWMs input clocks.
Since the number of possible input clocks is also different, the
'num_parents' field is added to all the Meson PWM data.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Switch the driver to atomic PWM. This makes it easier to wait a proper
amount of time when changing the duty cycle before disabling the channel
(main use case is switching the duty cycle to 0 before disabling).
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Implement .get_state instead of only reading the polarity at probe time.
This allows to get the proper state, period and duty cycle.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In of_pwm_get(), if we fail to get the PWM chip due to probe deferal, we
shouldn't print an error message. Just be silent in this case.
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The PWM hardware IP is taped-out with different maximum frequency
on different SoCs.
From HW team:
Before Tegra186, it is 48 MHz.
In Tegra186, it is 102 MHz.
Add support to limit the clock source frequency to the maximum IP
supported frequency. Provide these values via SoC chipdata.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Now that the JZ4740 and similar SoCs have a pinctrl driver, we rely on
the pins being properly configured before the driver probes.
One inherent problem of this new approach is that the pinctrl framework
does not allow us to configure each pin on demand, when the various PWM
channels are requested or released. For instance, the PWM channels can
be configured from sysfs, which would require all PWM pins to be configured
properly beforehand for the PWM function, eventually causing conflicts
with other platform or board drivers.
The proper solution here would be to modify the pwm-jz4740 driver to
handle only one PWM channel, and create an instance of this driver
for each one of the 8 PWM channels. Then, it could use the pinctrl
framework to dynamically configure the PWM pin it controls.
Until this can be done, the only jz4740 board supported upstream
(Qi lb60) can configure all of its connected PWM pins in PWM function
mode, since those are not used by other drivers nor by GPIOs on the
board.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is required to know the PWM clock source frequency to calculate the
PWM period.
In driver, the clock source frequency of the PWM does not get change
and, hence, get the clock source frequency in driver init. Get this
values later for period calculation from pwm_config().
This will help in avoiding the clock call for getting clock rate in the
pwm_config() each time.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
GPIO-only driver operation never clears the SLEEP bit, which can cause
the GPIOs to become unusable.
Example:
1. user requests first PWM -> driver clears SLEEP bit
2. user frees last PWM -> driver sets SLEEP bit
3. user requests GPIO
4. user switches GPIO on -> output does not turn on
because SLEEP bit is set
Prevent this behaviour by letting the runtime PM framework control the
SLEEP bit. This will put the chip to SLEEP if no PWMs/GPIOs are exported
or in use.
Fixes: bccec89f0a ("Allow any of the 16 PWMs to be used as a GPIO")
Reported-by: Sven Van Asbroeck <TheSven73@googlemail.com>
Signed-off-by: Sven Van Asbroeck <TheSven73@googlemail.com>
Suggested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
drivers/pwm/pwm-mediatek.c:210:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: John Crispin <john@phrozen.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
For very short periods, the result of the division might overflow the
unsigned long hz variable (on 32-bit architectures). Avoid that by
making it an unsigned long long. While at it, also remove an unneeded
local variable whose only purpose is to store a temporary computation.
Acked-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
In some of NVIDIA Tegra's platform, PWM controller is used to
control the PWM controlled regulators. PWM signal is connected to
the VID pin of the regulator where duty cycle of PWM signal decide
the voltage level of the regulator output.
When system enters suspend, some PWM client/slave regulator devices
require the PWM output to be tristated.
Add support to configure the pin state via pinctrl frameworks in
suspend and active state of the system.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The rate of the PWM calculated as follows:
hz = NSEC_PER_SEC / period_ns;
rate = (rate + (hz / 2)) / hz;
This has the precision loss in lower PWM rate.
Change this to have more precision as:
hz = DIV_ROUND_CLOSEST_ULL(NSEC_PER_SEC * 100, period_ns);
rate = DIV_ROUND_CLOSEST(rate * 100, hz)
Example:
1. period_ns = 16672000, PWM clock rate is 200 KHz.
Based on old formula
hz = NSEC_PER_SEC / period_ns
= 1000000000ul/16672000
= 59 (59.98)
rate = (200K + 59/2)/59 = 3390
Based on new method:
hz = 5998
rate = DIV_ROUND_CLOSE(200000*100, 5998) = 3334
If we measure the PWM signal rate, we will get more accurate
period with rate value of 3334 instead of 3390.
2. period_ns = 16803898, PWM clock rate is 200 KHz.
Based on old formula:
hz = 59, rate = 3390
Based on new formula:
hz = 5951, rate = 3360
The PWM signal rate of 3360 is more near to requested period
than 3333.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Use macro DIV_ROUND_CLOSEST_ULL() for 64-bit division to closest one
instead of implementing the same locally. This increase readability.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patch adds support for the PWM core found on current ARM base SoCs
made by MediaTek. This IP core supports 5 channels and has 2 operational
modes. There is the old mode, which is a classical PWM and the new mode
which allows the user to define bitmasks that get clocked out on the
pins. As the subsystem currently only supports PWM cores with the "old"
mode, we can safely ignore the "new" mode for now.
Signed-off-by: John Crispin <john@phrozen.org>
[thierry.reding@gmail.com: minor cleanups]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
sama5d2 can use the same atmel_pwm_data as sama5d3.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The currently Atmel PWM controllers supported by this driver could
change period or duty factor without channel disable, for regular
channels (sama5d3 support this by using period or duty factor update
registers, sam9rl support this by writing channel update register and
select the corresponding update: period or duty factor). The chip
doesn't support run time changings of signal polarity. To take advantage
of atomic PWM framework and let controller works without glitches, in
this patch only the duty factor could be changed without disabling PWM
channel. For period and signal polarity the atomic PWM is simulated by
disabling + enabling the right PWM channel.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Implement the suspend/resume hooks to make sure the PWM device is
restored to a correct state after a suspend.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Implement the ->apply() hook and drop the ->enable(), ->disable,
->set_polarity and ->config() ones.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
If the PWM was not enabled at U-Boot loader, PWM could not work for
clock always disabled at PWM driver. The PWM clock is enabled at
beginning of pwm_apply(), but disabled at end of pwm_apply().
If the PWM was enabled at U-Boot loader, PWM clock is always enabled
unless closed by ATF. The pwm-backlight might turn off the power at
early suspend, should disable PWM clock for saving power consume.
It is important to provide opportunity to enable/disable clock at PWM
driver, the PWM consumer should ensure correct order to call PWM enable
and disable, and PWM driver ensure state of PWM clock synchronized with
PWM enabled state.
Fixes: 2bf1c98aa5 ("pwm: rockchip: Add support for atomic update")
Cc: stable@vger.kernel.org
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
At least on cherrytrail, the update bit will never go low when the
enabled bit is not set.
This causes the backlight on my cube iwork8 air tablet to never turn on
again after being turned off because in the pwm_lpss_apply enable path
pwm_lpss_update will fail causing an error exit and the enable-bit to
never get set. Any following pwm_lpss_apply calls will fail the
pwm_lpss_is_updating check.
Since the docs say that the update bit should be set before the
enable-bit, split pwm_lpss_update into setting the update-bit and
pwm_lpss_wait_for_update, and move the pwm_lpss_wait_for_update call
in the enable path to after setting the enable-bit.
Fixes: 10d56a4 ("pwm: lpss: Avoid reconfiguring while UPDATE bit...")
Cc: Ilkka Koskinen <ilkka.koskinen@intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
As a preparation for special treatment for Broxton we split Tangier
configuration.
Fixes: b89b4b7a3d ("pwm: lpss: pci: Enable PWM module on Intel Edison")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This set contains mostly fixes to existing drivers as well as cleanup of
code that's not been in active use for a while.
-----BEGIN PGP SIGNATURE-----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=J9q4
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"This set contains mostly fixes to existing drivers as well as cleanup
of code that's not been in active use for a while"
* tag 'pwm/for-4.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (27 commits)
acpi: lpss: call pwm_add_table() for BSW PWM device
pwm: Try to load modules during pwm_get()
pwm: Don't hold pwm_lookup_lock longer than necessary
pwm: Make the PWM_POLARITY flag in DTB optional
pwm: Print error messages with pr_err() instead of pr_debug()
pwm: imx: Add polarity inversion support to i.MX's PWMv2
pwm: imx: doc: Update imx-pwm.txt documentation entry
pwm: imx: Remove redundant i.MX PWMv2 code
pwm: imx: Provide atomic PWM support for i.MX PWMv2
pwm: imx: Move PWMv2 wait for fifo slot code to a separate function
pwm: imx: Move PWMv2 software reset code to a separate function
pwm: imx: Rewrite v1 code to facilitate switch to atomic PWM
pwm: imx: Add separate set of PWM ops for v1 and v2
pwm: imx: Remove ipg clock and enable per clock when required
pwm: lpss: Add Intel Gemini Lake PCI ID
pwm: lpss: Do not export board infos for different PWM types
pwm: lpss: Avoid reconfiguring while UPDATE bit is still enabled
pwm: lpss: Switch to new atomic API
pwm: lpss: Allow duty cycle to be 0
pwm: lpss: Avoid potential overflow of base_unit
...
Add a module name string to the pwm_lookup struct and if specified try
to load the module using request_module() if pwmchip_find_by_name() is
unable to find the PWM chip.
This is a last resort to work around drivers that can't - and can't be
made to - deal with deferred probe.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
[thierry.reding@gmail.com: rename new macro, reword commit message]
[thierry.reding@gmail.com: add comment explaining use-case]
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
There is no need to hold pwm_lookup_lock after we're done with looping
over pwm_lookup_list, so release it earlier.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Change the PWM chip driver registration so that a chip driver that
supports polarity inversion can still be used with DTBs that don't
provide the polarity flag as part of the specifier.
This is done to provide polarity inversion support for the pwm-imx
driver without having to modify all existing DTS files.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Suggested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Make the messages that are printed in case of fatal errors actually
visible to the user without having to recompile the driver with
debugging enabled.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
With this patch the polarity settings for i.MX's PWMv2 is now supported
on top of atomic PWM setting
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The code providing functionality surpassed by the atomic PWM is not
needed anymore and hence can be removed.
Suggested-by: Stefan Agner <stefan@agner.ch>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The code, which waits for fifo slot, has been extracted from
imx_pwm_config_v2 function and moved to new one - imx_pwm_wait_fifo_slot().
This change reduces the overall size of imx_pwm_config_v2() and prepares
it for atomic PWM operation.
Suggested-by: Stefan Agner <stefan@agner.ch>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The software reset code has been extracted from imx_pwm_config_v2 function
and moved to new one - imx_pwm_sw_reset().
This change reduces the overall size of imx_pwm_config_v2() and prepares
it for atomic PWM operation.
Suggested-by: Stefan Agner <stefan@agner.ch>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The code has been rewritten to remove "generic" calls to
imx_pwm_{enable|disable|config}.
Such approach would facilitate switch to atomic PWM (a.k.a ->apply())
implementation.
Suggested-by: Stefan Agner <stefan@agner.ch>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
This patch provides separate set of PWM operations utilized by i.MX's
v1 and v2 of the PWM hardware.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Bhuvanchandra DV <bhuvanchandra.dv@toradex.com>
Signed-off-by: Lukasz Majewski <l.majewski@majess.pl>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
The use of the ipg clock was introduced with commit 7b27c160c6 ("pwm:
i.MX: fix clock lookup"). In the commit message it was claimed that the
ipg clock is enabled for register accesses. This is true for the
->config() callback, but not for the ->set_enable() callback. Given that
the ipg clock is not consistently enabled for all register accesses we
can assume that either it is not required at all or that the current
code does not work. Remove the ipg clock code for now so that it's no
longer in the way of refactoring the driver.
On the other hand, the i.MX 7 IP requires the peripheral clock to be
enabled before accessing its registers. Since ->config() can be called
when the PWM is disabled (in which case, the peripheral clock is also
disabled), we need to surround the imx->config() with
clk_prepare_enable(per_clk)/clk_disable_unprepare(per_clk) calls.
Note that the driver was working fine for the i.MX 7 IP so far because
the ipg and peripheral clock use the same hardware clock gate, which
guaranteed peripheral clock activation even when ->config() was called
when the PWM was disabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Intel Gemini Lake PWM is pretty much same as used in Intel Broxton. Add
this new PCI ID to the list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Thierry Reding <thierry.reding@gmail.com>
Hans de Goede