Add prints to identify the internal DCMD opcode that has timed out.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch enhances the existing debug prints in reset and task management
path.
These debug prints in adapter reset path helps with debugging issues
related to IO timeouts that are seen frequently in the field. Add
additional debug prints to dump the pending command frames before
initiating an adapter reset. Also, print FastPath IOs that are
outstanding.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Driver will use "reply descriptor post queues" in round robin fashion when
the combined MSI-X mode is not enabled. With this IO completions are
distributed and load balanced across all the available reply descriptor
post queues equally.
This is enabled only if combined MSI-X mode is not enabled in firmware.
This improves performance and also fixes soft lockups.
When load balancing is enabled, IRQ affinity from driver needs to be
disabled.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue Description:
We have seen cpu lock up issues from field if system has a large (more than
96) logical cpu count. SAS3.0 controller (Invader series) supports max 96
MSI-X vector and SAS3.5 product (Ventura) supports max 128 MSI-X vectors.
This may be a generic issue (if PCI device support completion on multiple
reply queues).
Let me explain it w.r.t megaraid_sas supported h/w just to simplify the
problem and possible changes to handle such issues. MegaRAID controller
supports multiple reply queues in completion path. Driver creates MSI-X
vectors for controller as "minimum of (FW supported Reply queues, Logical
CPUs)". If submitter is not interrupted via completion on same CPU, there
is a loop in the IO path. This behavior can cause hard/soft CPU lockups, IO
timeout, system sluggish etc.
Example - one CPU (e.g. CPU A) is busy submitting the IOs and another CPU
(e.g. CPU B) is busy with processing the corresponding IO's reply
descriptors from reply descriptor queue upon receiving the interrupts from
HBA. If CPU A is continuously pumping the IOs then always CPU B (which is
executing the ISR) will see the valid reply descriptors in the reply
descriptor queue and it will be continuously processing those reply
descriptor in a loop without quitting the ISR handler.
megaraid_sas driver will exit ISR handler if it finds unused reply
descriptor in the reply descriptor queue. Since CPU A will be continuously
sending the IOs, CPU B may always see a valid reply descriptor (posted by
HBA Firmware after processing the IO) in the reply descriptor queue. In
worst case, driver will not quit from this loop in the ISR handler.
Eventually, CPU lockup will be detected by watchdog.
Above mentioned behavior is not common if "rq_affinity" set to 2 or
affinity_hint is honored by irqbalancer as "exact". If rq_affinity is set
to 2, submitter will be always interrupted via completion on same CPU. If
irqbalancer is using "exact" policy, interrupt will be delivered to
submitter CPU.
Problem statement:
If CPU count to MSI-X vectors (reply descriptor Queues) count ratio is not
1:1, we still have exposure of issue explained above and for that we don't
have any solution.
Exposure of soft/hard lockup is seen if CPU count is more than MSI-X
supported by device.
If CPUs count to MSI-X vectors count ratio is not 1:1, (Other way, if
CPU counts to MSI-X vector count ratio is something like X:1, where X > 1)
then 'exact' irqbalance policy OR rq_affinity = 2 won't help to avoid CPU
hard/soft lockups. There won't be any one to one mapping between
CPU to MSI-X vector instead one MSI-X interrupt (or reply descriptor queue)
is shared with group/set of CPUs and there is a possibility of having a
loop in the IO path within that CPU group and may observe lockups.
For example: Consider a system having two NUMA nodes and each node having
four logical CPUs and also consider that number of MSI-X vectors enabled on
the HBA is two, then CPUs count to MSI-X vector count ratio as 4:1.
e.g.
MSI-X vector 0 is affinity to CPU 0, CPU 1, CPU 2 & CPU 3 of NUMA node 0 and
MSI-X vector 1 is affinity to CPU 4, CPU 5, CPU 6 & CPU 7 of NUMA node 1.
numactl --hardware
available: 2 nodes (0-1)
node 0 cpus: 0 1 2 3 --> MSI-X 0
node 0 size: 65536 MB
node 0 free: 63176 MB
node 1 cpus: 4 5 6 7 --> MSI-X 1
node 1 size: 65536 MB
node 1 free: 63176 MB
Assume that user started an application which uses all the CPUs of NUMA
node 0 for issuing the IOs. Only one CPU from affinity list (it can be any
cpu since this behavior depends upon irqbalance) CPU0 will receive the
interrupts from MSI-X 0 for all the IOs. Eventually, CPU 0 IO submission
percentage will be decreasing and ISR processing percentage will be
increasing as it is more busy with processing the interrupts. Gradually IO
submission percentage on CPU 0 will be zero and it's ISR processing
percentage will be 100% as IO loop has already formed within the
NUMA node 0, i.e. CPU 1, CPU 2 & CPU 3 will be continuously busy with
submitting the heavy IOs and only CPU 0 is busy in the ISR path as it
always find the valid reply descriptor in the reply descriptor queue.
Eventually, we will observe the hard lockup here.
Chances of occurring of hard/soft lockups are directly proportional to
value of X. If value of X is high, then chances of observing CPU lockups is
high.
Solution:
Use IRQ poll interface defined in "irq_poll.c".
megaraid_sas driver will execute ISR routine in softirq context and it will
always quit the loop based on budget provided in IRQ poll interface.
Driver will switch to IRQ poll only when more than a threshold number of
reply descriptors are handled in one ISR. Currently threshold is set as
1/4th of HBA queue depth.
In these scenarios (i.e. where CPUs count to MSI-X vectors count ratio is
X:1 (where X > 1)), IRQ poll interface will avoid CPU hard lockups due to
voluntary exit from the reply queue processing based on budget.
Note - Only one MSI-X vector is busy doing processing.
Select CONFIG_IRQ_POLL from driver Kconfig for driver compilation.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While an online controller reset(OCR) is in progress, there is short
duration where all access to controller's PCI config space from the host
needs to be blocked. This is due to a hardware limitation of MegaRAID
controllers.
With this patch, driver will block all access to controller's config space
from userland applications by calling pci_cfg_access_lock() while OCR is in
progress and unlocking after controller comes back to ready state.
Added helper function which locks the config space before initiating OCR
and wait for controller to become READY.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. This patch reworks code around controller reset path
which gets rid of a couple of goto labels. This is in preparation for the
next patch which adds PCI config space access locking while controller
reset is in progress.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
fw_reset_no_pci_access is only applicable for MFI controllers and is not
used for Fusion controllers.
For all Fusion controllers, driver can check reset adapter bit in
status register before performing a chip reset without
setting "fw_reset_no_pci_access".
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Remove set but unused variable in
megasas_set_static_target_properties.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is mostly update of the usual drivers: qla2xxx, qedf, smartpqi,
hpsa, lpfc, ufs, mpt3sas, ibmvfc and hisi_sas. Plus number of minor
changes, spelling fixes and other trivia.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXNIK0yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbeFAP4wsOm6
BNqDvLbF7gHAH+oSVAeENd9tepXG2xKbUHmLRgEA1wPaUxon8L8v/SSsqwewqMXP
y6CnU6aO2iaViTNBsPs=
=RX74
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: qla2xxx, qedf, smartpqi,
hpsa, lpfc, ufs, mpt3sas, ibmvfc and hisi_sas. Plus number of minor
changes, spelling fixes and other trivia"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (298 commits)
scsi: qla2xxx: Avoid that lockdep complains about unsafe locking in tcm_qla2xxx_close_session()
scsi: qla2xxx: Avoid that qlt_send_resp_ctio() corrupts memory
scsi: qla2xxx: Fix hardirq-unsafe locking
scsi: qla2xxx: Complain loudly about reference count underflow
scsi: qla2xxx: Use __le64 instead of uint32_t[2] for sending DMA addresses to firmware
scsi: qla2xxx: Introduce the dsd32 and dsd64 data structures
scsi: qla2xxx: Check the size of firmware data structures at compile time
scsi: qla2xxx: Pass little-endian values to the firmware
scsi: qla2xxx: Fix race conditions in the code for aborting SCSI commands
scsi: qla2xxx: Use an on-stack completion in qla24xx_control_vp()
scsi: qla2xxx: Make qla24xx_async_abort_cmd() static
scsi: qla2xxx: Remove unnecessary locking from the target code
scsi: qla2xxx: Remove qla_tgt_cmd.released
scsi: qla2xxx: Complain if a command is released that is owned by the firmware
scsi: qla2xxx: target: Fix offline port handling and host reset handling
scsi: qla2xxx: Fix abort handling in tcm_qla2xxx_write_pending()
scsi: qla2xxx: Fix error handling in qlt_alloc_qfull_cmd()
scsi: qla2xxx: Simplify qlt_send_term_imm_notif()
scsi: qla2xxx: Fix use-after-free issues in qla2xxx_qpair_sp_free_dma()
scsi: qla2xxx: Fix a qla24xx_enable_msix() error path
...
There are a couple of spelling mistakes in some kernel info and notice
messages. Fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fix sparse warning:
drivers/scsi/megaraid/megaraid_sas_base.c:4652:1: warning:
symbol 'megasas_host_device_list_query' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This is the final round of mostly small fixes and performance
improvements to our initial submit. The main regression fix is the
ia64 simscsi build failure which was missed in the serial number
elimination conversion.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIxBayYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pisherpAP4rxLpX
bcUnQnEsvoxys/JyoK08Qfv1JebZo1B2MAZ62wD/VZ7LpOuzVLhsM2KhLFGRrs1/
7D2K4tgtO2dQsFix7H0=
=pcHl
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull more SCSI updates from James Bottomley:
"This is the final round of mostly small fixes and performance
improvements to our initial submit.
The main regression fix is the ia64 simscsi build failure which was
missed in the serial number elimination conversion"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: ia64: simscsi: use request tag instead of serial_number
scsi: aacraid: Fix performance issue on logical drives
scsi: lpfc: Fix error codes in lpfc_sli4_pci_mem_setup()
scsi: libiscsi: Hold back_lock when calling iscsi_complete_task
scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink
scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port
scsi: hisi_sas: Set PHY linkrate when disconnected
scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
scsi: qla2xxx: check for kstrtol() failure
scsi: lpfc: fix 32-bit format string warning
scsi: lpfc: fix unused variable warning
scsi: target: tcmu: Switch to bitmap_zalloc()
scsi: libiscsi: fall back to sendmsg for slab pages
scsi: qla2xxx: avoid printf format warning
scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset
scsi: lpfc: Correct __lpfc_sli_issue_iocb_s4 lockdep check
scsi: ufs: hisi: fix ufs_hba_variant_ops passing
scsi: qla2xxx: Fix panic in qla_dfs_tgt_counters_show
...
This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core. Additionally Christoph
refactored gdth as part of the dma changes. The major mid-layer
change this time is the removal of bidi commands and with them the
whole of the osd/exofs driver and filesystem.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXIC54SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishT1GAPwJEV23
ExPiPsnuVgKj49nLTagZ3rILRQcYNbL+MNYqxQEA0cT8FHzSDBfWY5OKPNE+RQ8z
f69LpXGmMpuagKGvvd4=
=Fhy1
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly update of the usual drivers: arcmsr, qla2xxx, lpfc,
hisi_sas, target/iscsi and target/core.
Additionally Christoph refactored gdth as part of the dma changes. The
major mid-layer change this time is the removal of bidi commands and
with them the whole of the osd/exofs driver and filesystem. This is a
major simplification for block and mq in particular"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (240 commits)
scsi: cxgb4i: validate tcp sequence number only if chip version <= T5
scsi: cxgb4i: get pf number from lldi->pf
scsi: core: replace GFP_ATOMIC with GFP_KERNEL in scsi_scan.c
scsi: mpt3sas: Add missing breaks in switch statements
scsi: aacraid: Fix missing break in switch statement
scsi: kill command serial number
scsi: csiostor: drop serial_number usage
scsi: mvumi: use request tag instead of serial_number
scsi: dpt_i2o: remove serial number usage
scsi: st: osst: Remove negative constant left-shifts
scsi: ufs-bsg: Allow reading descriptors
scsi: ufs: Allow reading descriptor via raw upiu
scsi: ufs-bsg: Change the calling convention for write descriptor
scsi: ufs: Remove unused device quirks
Revert "scsi: ufs: disable vccq if it's not needed by UFS device"
scsi: megaraid_sas: Remove a bunch of set but not used variables
scsi: clean obsolete return values of eh_timed_out
scsi: sd: Optimal I/O size should be a multiple of physical block size
scsi: MAINTAINERS: SCSI initiator and target tweaks
scsi: fcoe: make use of fip_mode enum complete
...
megaraid_sas takes 1+ seconds to load while waiting for firmware:
[2.822603] megaraid_sas 0000:03:00.0: Waiting for FW to come to ready state
[3.871003] megaraid_sas 0000:03:00.0: FW now in Ready state
This is due to the following loop in megasas_transition_to_ready(), which
waits a minimum of 1 second, even though the FW becomes ready in tens of
millisecs:
/*
* The cur_state should not last for more than max_wait secs
*/
for (i = 0; i < max_wait; i++) {
...
msleep(1000);
...
dev_info(&instance->pdev->dev, "FW now in Ready state\n");
This is a regression, caused by a change of the msleep granularity from 1
to 1000 due to concern about waiting too long on systems with coarse
jiffies.
To fix, increase iterations and use msleep(20), which results in:
[2.670627] megaraid_sas 0000:03:00.0: Waiting for FW to come to ready state
[2.739386] megaraid_sas 0000:03:00.0: FW now in Ready state
Fixes: fb2f3e96d80f ("scsi: megaraid_sas: Fix msleep granularity")
Signed-off-by: Steve Sistare <steven.sistare@oracle.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'wait_and_poll':
drivers/scsi/megaraid/megaraid_sas_fusion.c:936:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_sync_map_info':
drivers/scsi/megaraid/megaraid_sas_fusion.c:1329:6: warning:
variable 'size_sync_info' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_init_adapter_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:1639:39: warning:
variable 'reg_set' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_is_prp_possible':
drivers/scsi/megaraid/megaraid_sas_fusion.c:1925:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_make_prp_nvme':
drivers/scsi/megaraid/megaraid_sas_fusion.c:2047:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_build_ldio_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:2620:42: warning:
variable 'req_desc' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_build_and_issue_cmd_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:3245:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_task_abort_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:4398:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_sas_fusion.c: In function 'megasas_reset_target_fusion':
drivers/scsi/megaraid/megaraid_sas_fusion.c:4484:25: warning:
variable 'fusion' set but not used [-Wunused-but-set-variable]
They're not used anymore and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
when create DMA pool for cmd frames failed, we should return -ENOMEM,
instead of 0.
In some case in:
megasas_init_adapter_fusion()
-->megasas_alloc_cmds()
-->megasas_create_frame_pool
create DMA pool failed,
--> megasas_free_cmds() [1]
-->megasas_alloc_cmds_fusion()
failed, then goto fail_alloc_cmds.
-->megasas_free_cmds() [2]
we will call megasas_free_cmds twice, [1] will kfree cmd_list,
[2] will use cmd_list.it will cause a problem:
Unable to handle kernel NULL pointer dereference at virtual address
00000000
pgd = ffffffc000f70000
[00000000] *pgd=0000001fbf893003, *pud=0000001fbf893003,
*pmd=0000001fbf894003, *pte=006000006d000707
Internal error: Oops: 96000005 [#1] SMP
Modules linked in:
CPU: 18 PID: 1 Comm: swapper/0 Not tainted
task: ffffffdfb9290000 ti: ffffffdfb923c000 task.ti: ffffffdfb923c000
PC is at megasas_free_cmds+0x30/0x70
LR is at megasas_free_cmds+0x24/0x70
...
Call trace:
[<ffffffc0005b779c>] megasas_free_cmds+0x30/0x70
[<ffffffc0005bca74>] megasas_init_adapter_fusion+0x2f4/0x4d8
[<ffffffc0005b926c>] megasas_init_fw+0x2dc/0x760
[<ffffffc0005b9ab0>] megasas_probe_one+0x3c0/0xcd8
[<ffffffc0004a5abc>] local_pci_probe+0x4c/0xb4
[<ffffffc0004a5c40>] pci_device_probe+0x11c/0x14c
[<ffffffc00053a5e4>] driver_probe_device+0x1ec/0x430
[<ffffffc00053a92c>] __driver_attach+0xa8/0xb0
[<ffffffc000538178>] bus_for_each_dev+0x74/0xc8
[<ffffffc000539e88>] driver_attach+0x28/0x34
[<ffffffc000539a18>] bus_add_driver+0x16c/0x248
[<ffffffc00053b234>] driver_register+0x6c/0x138
[<ffffffc0004a5350>] __pci_register_driver+0x5c/0x6c
[<ffffffc000ce3868>] megasas_init+0xc0/0x1a8
[<ffffffc000082a58>] do_one_initcall+0xe8/0x1ec
[<ffffffc000ca7be8>] kernel_init_freeable+0x1c8/0x284
[<ffffffc0008d90b8>] kernel_init+0x1c/0xe4
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add padding to make the structure variables in MR_HOST_DEVICE_LIST_ENTRY
64-bit aligned. Also, add reserved fields to MR_HOST_DEVICE_LIST for
future firmware usage.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for the new DEVICE_LIST DCMD.
Driver currently sends two separate DCMDs for getting the list of PDs and
LDs that are exposed to host. The new DCMD provides a single interface to
get a list of both PDs and LDs that are exposed to the host. Based on the
list of target IDs that are returned by this DCMD, driver will add the
devices (PD/LD) to SML. Driver will check for FW support for this new DCMD
and based on the support will either send the new DCMD or will fall back to
the earlier method of sending two separate DCMDs for PD and LD list.
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation of adding support for the DEVICE_LIST DCMD, this patch
refactors the code in the AEN event handling path. Add new function to
update the PD and LD list in driver. Move the code to scan PD and VD
channels into separate function.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During FW init, combine the code to get the PD and LD list from FW into a
single function. This patch is in preparation for adding support for
HOST_DEVICE_LIST DCMD.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A set of 17 fixes. Most of these are minor or trivial. The one fix
that may be serious is the isci one: the bug can cause hba parameters
to be set from uninitialized memory. I don't think it's exploitable,
but you never know.
Signed-off-by: James E.J. Bottomley <jejb@linux.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCXEKL0SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishVZpAQCwuPTk
fqOt4v4hJ0oUHtEBsQK3VMXSdUvWdb5Lbn3WeQD/RFYTyNxcIF7ADSWw71b+IigT
ejUrMzI8ig+nZ1jbFZ4=
=BdS/
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A set of 17 fixes. Most of these are minor or trivial.
The one fix that may be serious is the isci one: the bug can cause hba
parameters to be set from uninitialized memory. I don't think it's
exploitable, but you never know"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxgb4i: add wait_for_completion()
scsi: qla1280: set 64bit coherent mask
scsi: ufs: Fix geometry descriptor size
scsi: megaraid_sas: Retry reads of outbound_intr_status reg
scsi: qedi: Add ep_state for login completion on un-reachable targets
scsi: ufs: Fix system suspend status
scsi: qla2xxx: Use correct number of vectors for online CPUs
scsi: hisi_sas: Set protection parameters prior to adding SCSI host
scsi: tcmu: avoid cmd/qfull timers updated whenever a new cmd comes
scsi: isci: initialize shost fully before calling scsi_add_host()
scsi: lpfc: lpfc_sli: Mark expected switch fall-throughs
scsi: smartpqi_init: fix boolean expression in pqi_device_remove_start
scsi: core: Synchronize request queue PM status only on successful resume
scsi: pm80xx: reduce indentation
scsi: qla4xxx: check return code of qla4xxx_copy_from_fwddb_param
scsi: megaraid_sas: correct an info message
scsi: target/iscsi: fix error msg typo when create lio_qr_cache failed
scsi: sd: Fix cache_type_store()
commit 272652fcbf ("scsi: megaraid_sas: add retry logic in megasas_readl")
missed changing readl to megasas_readl in megasas_clear_intr_fusion(). For
Aero controllers, reads of outbound_intr_status register needs to be
retried.
Reported-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This was apparently forgotten in
894169db1 ("scsi: megaraid_sas: Use 63-bit DMA addressing").
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Although MegaRAID controllers support 64-bit DMA addressing, as per
hardware design, DMA address with all 64-bits set
(0xFFFFFFFF-FFFFFFFF) results in a firmware fault.
Driver will set 63-bit DMA mask to ensure the above address will not be
used.
Cc: stable@vger.kernel.org
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Due to hardware errata in Aero controllers, reads to certain fusion
registers could intermittently return zero. This behavior is
transient in nature and subsequent reads will return valid value.
For Aero controllers, any calls to readl to read from certain
registers will be retried for maximum three times, if read returns
zero.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Instead of the register address, pass the instance pointer to clear_intr
and read_fw_status_reg functions. This is done in preparation for adding
adapter type based checks in these functions in later patches of this
series.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Identify all Aero controller PCI IDs with new adapter type.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation for the new Aero series adapter type, all the places where
we check adapter type for Ventura series needs to include any later adapter
types.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page. Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
NULL check before some freeing functions is not needed.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Notice that, in this particular case, I replaced "Fall thru" with a "Fall
through" annotation and added a dash as a token in order to separate the
"Fall through" annotation from the rest of the comment on the same line,
which is what GCC is expecting to find.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds support for MegaRAID Aero controller PCI IDs. Print a
message when a configurable secure type controller is encountered.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The print related to number of VDs that a particular firmware supports is
misleading in some cases. Even though supportMaxExtLDs is set, certain
firmware profiles only supports upto 64VDs.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
IOC INIT frame needs to be fired with a timeout of 180 seconds.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In megasas_init_adapter_fusion(), max_mfi_cmds is being calcuated as
(MEGASAS_FUSION_INTERNAL_CMDS + MEGASAS_FUSION_IOCTL_CMDS). max_mfi_cmds
can be used in megasas_configure_queue_sizes.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rename the scratch pad registers to match firmware headers. No functional
change.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Optimization: No need to hold hba_lock in dpc context for reading atomic
variable.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change. Use local variables when accessing raid context in
IO path. Improves code readability.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When driver fails to start the heartbeat timer, exit from FW init.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For SRIOV based adapters, driver should not set the STOP_ADP bit as part of
kill adapter.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For Invader series, if FW supports more than 8 MSI-x vectors, driver needs
to enable combined reply queue mode. For Ventura series, driver enables
combined reply queue mode in case of more than 16 MSI-x vectors.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Module parameter description for rdpq_enable incorrectly lists the default
as enabled. Also, provide range of valid values for resetwaittime in the
description.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During init, if pci_alloc_irq_vectors() fails, the driver has not yet setup
the IRQs. Fix the goto labels and error handling for this case.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Change copyright to Broadcom Inc. Also update any references to Avago with
Broadcom. Update copyright duration wherever required.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For SAS3 and later controllers, FW sets the reset adapter bit indicating
the driver to perform a controller reset. Driver needs to check if this
bit is set before doing a reset. This reduces the driver probe failure
time to 180seconds in case there is a faulty controller connected.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In megasas_transition_to_ready() driver waits 180seconds for controller to
change FW state. Here we are calling msleep(1) in a loop for this. As
explained in timers-howto.txt, msleep(1) will actually sleep longer than
1ms. If a faulty controller is connected, we will end up waiting for much
more than 180 seconds causing unnecessary delays during load.
Change the granularity of msleep() call from 1ms to 1000ms.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Latest firmware adds a mechanism to save firmware logs just before
controller reset on pre-allocated internal controller DRAM. This feature is
called snapdump which will help debugging firmware issues. This feature
requires extra time and firmware reports these values through new driver
interface. Before initiating an OCR, driver needs to inform FW to save a
snapdump and then wait for a specified time for the snapdump to complete.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently driver checks for Firmware state change from ISR context, and
only when there are interrupts tied with no I/O completions. We have seen
multiple cases where doorbell interrupts sent by firmware to indicate FW
state change are not processed by driver and it takes long time for driver
to trigger OCR. And if there are no IOs running, since we only check the FW
state as part of ISR code, fault goes undetected by driver and OCR will not
be triggered.
This patch introduces a separate workqueue that runs every one second to
detect Firmware FAULT state and trigger reset immediately. As an
additional gain, removing PCI reads from ISR to check FW state results in
improved performance as well.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Switch from the legacy PCI DMA API to the generic DMA API.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/scsi/megaraid/megaraid_mbox.c: In function 'megaraid_reset_handler':
drivers/scsi/megaraid/megaraid_mbox.c:2580:7: warning:
variable 'recovering' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_mbox.c: In function 'mbox_post_sync_cmd':
drivers/scsi/megaraid/megaraid_mbox.c:2728:12: warning:
variable 'mbox64' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_mbox.c: In function 'megaraid_mbox_support_random_del':
drivers/scsi/megaraid/megaraid_mbox.c:3138:11: warning:
variable 'mbox' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_mbox.c: In function 'megaraid_mbox_flush_cache':
drivers/scsi/megaraid/megaraid_mbox.c:3266:10: warning:
variable 'mbox' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_mbox.c: In function 'megaraid_mbox_fire_sync_cmd':
drivers/scsi/megaraid/megaraid_mbox.c:3302:12: warning:
variable 'mbox64' set but not used [-Wunused-but-set-variable]
drivers/scsi/megaraid/megaraid_mbox.c: In function 'gather_hbainfo':
drivers/scsi/megaraid/megaraid_mbox.c:3797:10: warning:
variable 'dmajor' set but not used [-Wunused-but-set-variable]
[mkp: applied by hand due to conflict with hch's DMA cleanup]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In megasas_mgmt_compat_ioctl_fw(), to handle the structure
compat_megasas_iocpacket 'cioc', a user-space structure megasas_iocpacket
'ioc' is allocated before megasas_mgmt_ioctl_fw() is invoked to handle
the packet. Since the two data structures have different fields, the data
is copied from 'cioc' to 'ioc' field by field. In the copy process,
'sense_ptr' is prepared if the field 'sense_len' is not null, because it
will be used in megasas_mgmt_ioctl_fw(). To prepare 'sense_ptr', the
user-space data 'ioc->sense_off' and 'cioc->sense_off' are copied and
saved to kernel-space variables 'local_sense_off' and 'user_sense_off'
respectively. Given that 'ioc->sense_off' is also copied from
'cioc->sense_off', 'local_sense_off' and 'user_sense_off' should have the
same value. However, 'cioc' is in the user space and a malicious user can
race to change the value of 'cioc->sense_off' after it is copied to
'ioc->sense_off' but before it is copied to 'user_sense_off'. By doing
so, the attacker can inject different values into 'local_sense_off' and
'user_sense_off'. This can cause undefined behavior in the following
execution, because the two variables are supposed to be same.
This patch enforces a check on the two kernel variables 'local_sense_off'
and 'user_sense_off' to make sure they are the same after the copy. In
case they are not, an error code EINVAL will be returned.
Signed-off-by: Wenwen Wang <wang6495@umn.edu>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The dma_map_sg / dma_unmap_sg APIs called from scsi_dma_map /
scsi_dma_unmap already transfer memory ownership to the device or cpu
respectively. Adding additional calls to pci_dma_sync_sg_* will in fact
lead to data corruption if we end up using swiotlb for some reason.
Also remove the now pointless megaraid_mbox_sync_scb function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Trivial fix to spelling mistake in warning message and comments
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional change.
Just introduce scsi_host_busy() and replace the direct read of
scsi_host->host_busy with this new API.
Cc: Omar Sandoval <osandov@fb.com>,
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <james.bottomley@hansenpartnership.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: Don Brace <don.brace@microsemi.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Firmware provides drive specific target reset and task abort timeout
values. Driver needs to use these timeout values during task management
calls. If FW does not provide these values, fall back to using earlier
default timeout of 50 seconds for TM.
[mkp: clarified comment]
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
While driver is waiting for adapter to become operational, if a kill
adapter is issued, driver can bail out from the wait loop immediately
rather than waiting for the entire 180 seconds.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There is a possibility that firmware on the controller was upgraded before
system was suspended. During resume, driver needs to read updated
controller properties.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If MR_DCMD_CTRL_GET_INFO DCMD timed out, return failure rather than doing
kill adapter.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
xfcp, hisi_sas, cxlflash, qla2xxx. In the absence of Nic, we're also
taking target updates which are mostly minor except for the tcmu
refactor. The only real core change to worry about is the removal of
high page bouncing (in sas, storvsc and iscsi). This has been well
tested and no problems have shown up so far.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWx1pbCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishUucAP42pccS
ziKyiOizuxv9fZ4Q+nXd1A9zhI5tqqpkHjcQegEA40qiZSi3EKGKR8W0UpX7Ntmo
tqrZJGojx9lnrAM2RbQ=
=NMXg
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates to the usual drivers: ufs, qedf, mpt3sas, lpfc,
xfcp, hisi_sas, cxlflash, qla2xxx.
In the absence of Nic, we're also taking target updates which are
mostly minor except for the tcmu refactor.
The only real core change to worry about is the removal of high page
bouncing (in sas, storvsc and iscsi). This has been well tested and no
problems have shown up so far"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (268 commits)
scsi: lpfc: update driver version to 12.0.0.4
scsi: lpfc: Fix port initialization failure.
scsi: lpfc: Fix 16gb hbas failing cq create.
scsi: lpfc: Fix crash in blk_mq layer when executing modprobe -r lpfc
scsi: lpfc: correct oversubscription of nvme io requests for an adapter
scsi: lpfc: Fix MDS diagnostics failure (Rx < Tx)
scsi: hisi_sas: Mark PHY as in reset for nexus reset
scsi: hisi_sas: Fix return value when get_free_slot() failed
scsi: hisi_sas: Terminate STP reject quickly for v2 hw
scsi: hisi_sas: Add v2 hw force PHY function for internal ATA command
scsi: hisi_sas: Include TMF elements in struct hisi_sas_slot
scsi: hisi_sas: Try wait commands before before controller reset
scsi: hisi_sas: Init disks after controller reset
scsi: hisi_sas: Create a scsi_host_template per HW module
scsi: hisi_sas: Reset disks when discovered
scsi: hisi_sas: Add LED feature for v3 hw
scsi: hisi_sas: Change common allocation mode of device id
scsi: hisi_sas: change slot index allocation mode
scsi: hisi_sas: Introduce hisi_sas_phy_set_linkrate()
scsi: hisi_sas: fix a typo in hisi_sas_task_prep()
...
The BLK_EH_NOT_HANDLED implies nothing happen, but very often that
is not what is happening - instead the driver already completed the
command. Fix the symbolic name to reflect that a little better.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Trivial fix to spelling mistake in module parameter description text
[mkp: applied by hand]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Fixes: 2d2c233167 ("scsi: megaraid_sas: modified few prints in OCR and IOC INIT path")
Signed-off-by: Vinson Lee <vlee@freedesktop.org>
Acked-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Hardware could time out Fastpath IOs one second earlier than the timeout
provided by the host.
For non-RAID devices, driver provides timeout value based on OS provided
timeout value. Under certain scenarios, if the OS provides a timeout
value of 1 second, due to above behavior hardware will timeout
immediately.
Increase timeout value for non-RAID fastpath IOs by 1 second.
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use pci_zalloc_consistent for allocating zeroed memory and remove
unnecessary memset function.
Done using Coccinelle.
Generated by: scripts/coccinelle/api/alloc/kzalloc-simple.cocci
Suggested-by: Luis R. Rodriguez <mcgrof@kernel.org>
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is mostly updates of the usual drivers: arcmsr, qla2xx, lpfc,
ufs, mpt3sas, hisi_sas. In addition we have removed several really
old drivers: sym53c416, NCR53c406a, fdomain, fdomain_cs and removed
the old scsi_module.c initialization from all remaining drivers. Plus
an assortment of bug fixes, initialization errors and other minor
fixes.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWsVSnSYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishbvbAP9ErpTZ
OR5iJ5HIz4W3Bd8aTfEpJrDyeYwSUC+sra5SKQD/ZWyVB3fYFSg+ZROyT26pmtmd
SdImhG7hLaHgVvF5qRQ=
=SQ/n
-----END PGP SIGNATURE-----
Merge tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual drivers: arcmsr, qla2xx, lpfc,
ufs, mpt3sas, hisi_sas.
In addition we have removed several really old drivers: sym53c416,
NCR53c406a, fdomain, fdomain_cs and removed the old scsi_module.c
initialization from all remaining drivers.
Plus an assortment of bug fixes, initialization errors and other minor
fixes"
* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (168 commits)
scsi: ufs: Add support for Auto-Hibernate Idle Timer
scsi: ufs: sysfs: reworking of the rpm_lvl and spm_lvl entries
scsi: qla2xxx: fx00 copypaste typo
scsi: qla2xxx: fix error message on <qla2400
scsi: smartpqi: update driver version
scsi: smartpqi: workaround fw bug for oq deletion
scsi: arcmsr: Change driver version to v1.40.00.05-20180309
scsi: arcmsr: Sleep to avoid CPU stuck too long for waiting adapter ready
scsi: arcmsr: Handle adapter removed due to thunderbolt cable disconnection.
scsi: arcmsr: Rename ACB_F_BUS_HANG_ON to ACB_F_ADAPTER_REMOVED for adapter hot-plug
scsi: qla2xxx: Update driver version to 10.00.00.06-k
scsi: qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan
scsi: qla2xxx: Cleanup code to improve FC-NVMe error handling
scsi: qla2xxx: Fix FC-NVMe IO abort during driver reset
scsi: qla2xxx: Fix retry for PRLI RJT with reason of BUSY
scsi: qla2xxx: Remove nvme_done_list
scsi: qla2xxx: Return busy if rport going away
scsi: qla2xxx: Fix n2n_ae flag to prevent dev_loss on PDB change
scsi: qla2xxx: Add FC-NVMe abort processing
scsi: qla2xxx: Add changes for devloss timeout in driver
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=RVhK
-----END PGP SIGNATURE-----
Merge tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block
Pull block layer updates from Jens Axboe:
"It's a pretty quiet round this time, which is nice. This contains:
- series from Bart, cleaning up the way we set/test/clear atomic
queue flags.
- series from Bart, fixing races between gendisk and queue
registration and removal.
- set of bcache fixes and improvements from various folks, by way of
Michael Lyle.
- set of lightnvm updates from Matias, most of it being the 1.2 to
2.0 transition.
- removal of unused DIO flags from Nikolay.
- blk-mq/sbitmap memory ordering fixes from Omar.
- divide-by-zero fix for BFQ from Paolo.
- minor documentation patches from Randy.
- timeout fix from Tejun.
- Alpha "can't write a char atomically" fix from Mikulas.
- set of NVMe fixes by way of Keith.
- bsg and bsg-lib improvements from Christoph.
- a few sed-opal fixes from Jonas.
- cdrom check-disk-change deadlock fix from Maurizio.
- various little fixes, comment fixes, etc from various folks"
* tag 'for-4.17/block-20180402' of git://git.kernel.dk/linux-block: (139 commits)
blk-mq: Directly schedule q->timeout_work when aborting a request
blktrace: fix comment in blktrace_api.h
lightnvm: remove function name in strings
lightnvm: pblk: remove some unnecessary NULL checks
lightnvm: pblk: don't recover unwritten lines
lightnvm: pblk: implement 2.0 support
lightnvm: pblk: implement get log report chunk
lightnvm: pblk: rename ppaf* to addrf*
lightnvm: pblk: check for supported version
lightnvm: implement get log report chunk helpers
lightnvm: make address conversions depend on generic device
lightnvm: add support for 2.0 address format
lightnvm: normalize geometry nomenclature
lightnvm: complete geo structure with maxoc*
lightnvm: add shorten OCSSD version in geo
lightnvm: add minor version to generic geometry
lightnvm: simplify geometry structure
lightnvm: pblk: refactor init/exit sequences
lightnvm: Avoid validation of default op value
lightnvm: centralize permission check for lightnvm ioctl
...
Somewhat nasty merge due to conflicts between "33b28357dd00 scsi:
qla2xxx: Fix Async GPN_FT for FCP and FC-NVMe scan" and "2b5b96473efc
scsi: qla2xxx: Fix FC-NVMe LUN discovery"
Merge is non-trivial and has been verified by Qlogic (Cavium)
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
Two driver fixes (ibmvfc, iscsi_tcp) and a USB fix for devices that
give the wrong return to Read Capacity and cause a huge log spew. The
remaining 5 patches all try to fix commit 84676c1f21
"genirq/affinity: assign vectors to all possible CPUs") which broke
the non-mq I/O path.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWrpSmyYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishY+MAP9Zvin/
AUc3xkvOPdIzRPp2aXQHJKC+NGmNFr6MiXIHiAD/TvjbkxEjbUTjnr+gZNaloDma
d/I4i9xaBNSvqNJpzT0=
=mLIX
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Two driver fixes (ibmvfc, iscsi_tcp) and a USB fix for devices that
give the wrong return to Read Capacity and cause a huge log spew.
The remaining five patches all try to fix commit 84676c1f21
("genirq/affinity: assign vectors to all possible CPUs") which broke
the non-mq I/O path"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: iscsi_tcp: set BDI_CAP_STABLE_WRITES when data digest enabled
scsi: sd: Remember that READ CAPACITY(16) succeeded
scsi: ibmvfc: Avoid unnecessary port relogin
scsi: virtio_scsi: unify scsi_host_template
scsi: virtio_scsi: fix IO hang caused by automatic irq vector affinity
scsi: core: introduce force_blk_mq
scsi: megaraid_sas: fix selection of reply queue
scsi: hpsa: fix selection of reply queue
Since commit 84676c1f21 ("genirq/affinity: assign vectors to all
possible CPUs") we could end up with an MSI-X vector that did not have
any online CPUs mapped. This would lead to I/O hangs since there was no
CPU to receive the completion.
Retrieve IRQ affinity information using pci_irq_get_affinity() and use
this mapping to choose a reply queue.
[mkp: tweaked commit desc]
Cc: Hannes Reinecke <hare@suse.de>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>,
Cc: James Bottomley <james.bottomley@hansenpartnership.com>,
Cc: Christoph Hellwig <hch@lst.de>,
Cc: Don Brace <don.brace@microsemi.com>
Cc: Kashyap Desai <kashyap.desai@broadcom.com>
Cc: Laurence Oberman <loberman@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Meelis Roos <mroos@linux.ee>
Cc: Artem Bityutskiy <artem.bityutskiy@intel.com>
Fixes: 84676c1f21 ("genirq/affinity: assign vectors to all possible CPUs")
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Acked-by: Kashyap Desai <kashyap.desai@broadcom.com>
Tested-by: Kashyap Desai <kashyap.desai@broadcom.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch has been generated as follows:
for verb in set_unlocked clear_unlocked set clear; do
replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
$(git grep -lw queue_flag_${verb} drivers block/bsg*)
done
Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch is mostly fixes for driver specific issues (nine of them)
and the storvsc performance improvement with interrupt handling which
was dropped from the previous fixes pull request. We also have two
regressions: one is a double call_rcu() in ATA error handling and the
other is a missed conversion to BLK_STS_OK in
__scsi_error_from_host_byte().
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWp7/dCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSYAAP0RiYSR
oq3yLesh09tx0u+w2He8ylpdVizIzNMTjNE+BAD9GqeQWEvNaoGPUwNeMFJuwawX
hNjOttF1YOfFlsuoG94=
=9e1j
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is mostly fixes for driver specific issues (nine of them) and the
storvsc performance improvement with interrupt handling which was
dropped from the previous fixes pull request.
We also have two regressions: one is a double call_rcu() in ATA error
handling and the other is a missed conversion to BLK_STS_OK in
__scsi_error_from_host_byte()"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qedi: Fix kernel crash during port toggle
scsi: qla2xxx: Fix FC-NVMe LUN discovery
scsi: core: return BLK_STS_OK for DID_OK in __scsi_error_from_host_byte()
scsi: core: Avoid that ATA error handling can trigger a kernel hang or oops
scsi: qla2xxx: ensure async flags are reset correctly
scsi: qla2xxx: do not check login_state if no loop id is assigned
scsi: qla2xxx: Fixup locking for session deletion
scsi: qla2xxx: Fix NULL pointer crash due to active timer for ABTS
scsi: mpt3sas: wait for and flush running commands on shutdown/unload
scsi: mpt3sas: fix oops in error handlers after shutdown/unload
scsi: storvsc: Spread interrupts when picking a channel for I/O requests
scsi: megaraid_sas: Do not use 32-bit atomic request descriptor for Ventura controllers
Use dma_pool_zalloc() instead of dma_pool_alloc + memset
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Problem Statement: Sending I/O through 32 bit descriptors to Ventura series of
controller results in IO timeout on certain conditions.
This error only occurs on systems with high I/O activity on Ventura series
controllers.
Changes in this patch will prevent driver from using 32 bit descriptor and use
64 bit Descriptors.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is mostly updates of the usual driver suspects: arcmsr,
scsi_debug, mpt3sas, lpfc, cxlflash, qla2xxx, aacraid, megaraid_sas,
hisi_sas. We also have a rework of the libsas hotplug handling to
make it more robust, a slew of 32 bit time conversions and fixes, and
a host of the usual minor updates and style changes. The biggest
potential for regressions is the libsas hotplug changes, but so far
they seem stable under testing.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWnH+5SYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishWxuAP0UvuJp
MNR/yU/wv/emSzOc48Ldwd7I0xD2XxSnloGUgwD+IGZZT5yNUQA1THCbm+en4hkB
WvyBieQs9qRit+2czd4=
=gJMf
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This is mostly updates of the usual driver suspects: arcmsr,
scsi_debug, mpt3sas, lpfc, cxlflash, qla2xxx, aacraid, megaraid_sas,
hisi_sas.
We also have a rework of the libsas hotplug handling to make it more
robust, a slew of 32 bit time conversions and fixes, and a host of the
usual minor updates and style changes. The biggest potential for
regressions is the libsas hotplug changes, but so far they seem stable
under testing"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (313 commits)
scsi: qla2xxx: Fix logo flag for qlt_free_session_done()
scsi: arcmsr: avoid do_gettimeofday
scsi: core: Add VENDOR_SPECIFIC sense code definitions
scsi: qedi: Drop cqe response during connection recovery
scsi: fas216: fix sense buffer initialization
scsi: ibmvfc: Remove unneeded semicolons
scsi: hisi_sas: fix a bug in hisi_sas_dev_gone()
scsi: hisi_sas: directly attached disk LED feature for v2 hw
scsi: hisi_sas: devicetree: bindings: add LED feature for v2 hw
scsi: megaraid_sas: NVMe passthrough command support
scsi: megaraid: use ktime_get_real for firmware time
scsi: fnic: use 64-bit timestamps
scsi: qedf: Fix error return code in __qedf_probe()
scsi: devinfo: fix format of the device list
scsi: qla2xxx: Update driver version to 10.00.00.05-k
scsi: qla2xxx: Add XCB counters to debugfs
scsi: qla2xxx: Fix queue ID for async abort with Multiqueue
scsi: qla2xxx: Fix warning for code intentation in __qla24xx_handle_gpdb_event()
scsi: qla2xxx: Fix warning during port_name debug print
scsi: qla2xxx: Fix warning in qla2x00_async_iocb_timeout()
...
NVMe passthrough via MFI interface. Current MegaRAID product supports
different types of encapsulation via the MFI framework.
NVMe native command should be framed by application and it should be
embedded in MFI as payload. The driver will provide interface to send
the MFI frame along with the payload (in this case, payload is NVMe
native command) to the firmware. Driver already has an existing, similar
interface for SATA and SMP passthrough.
1. Driver will pass MFI command to the firmware if the latter supports
NVMe encapsulated processing (not all SAS3.5 firmware supports this
feature).
2. Driver exposes sysfs entry support_nvme_encapsulation. This is
required for backward compatibility for applications using earlier
driver versions that did not process IOCTL frames and could result in
host hang.
This is already fixed as part of commit 82add4e1b3 ("scsi:
megaraid_sas: Incorrect processing of IOCTL frames for SMP/STP
commands")
[mkp: clarified commit message]
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
do_gettimeofday() overflows in 2038 on 32-bit architectures and is
deprecated, so convert this driver to call ktime_get_real()
directly. This also simplifies the calculation.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional changes.
This patch is a re-work of DCMD refire code to better manage all the
different cases to decide whether to REFIRE or SKIP or COMPLETE certain
DCMD.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Expose FW outstanding commands (fw_outstanding) through sysfs interface.
This helps in debugging certain performance issues in the field.
Signed-off-by: Sasikumar Chandrasekaran <sasikumar.pc@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Performance improvement:
Current driver calls stream detection unconditionally for all IOs.
Stream Detection logic is not required for most of the fast path IO. To
improve performance, avoid stream detection logic and do it only if
required.
Below are the cases where stream detection is required in driver:
1. All non-FastPath IOs (IOs going to FW)
2. Fast Path reads sent to ReadAhead capable VDs.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Issue – There may be some IO accessing incorrect raid map, but driver
has checks in IO path to handle those cases. It is always better to move
to new raid map only once raid map is populated and validated. No
functional defect. Fix is provided as part of review. Fix – Update
instance->map_id after driver has populated new driver raid map from
firmware raid map.
Signed-off-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Shivasharan S