- Nicer debugfs output with one pin/config pair per line.
- Continued efforts to strictify module vs bool.
- Constification and similar from Coccinelle engineers.
- Return error from pinctrl_bind_pins()
- Pulling in the ability to selectively disable mapping of
unusable IRQs from the GPIO subsystem.
New drivers:
- New driver for the Aspeed pin controller family: AST2400 (G4)
and AST2500 (G5) are supported. These are used by OpenBMC
on the IBM Witherspoon platform.
- New subdriver for the Allwinner sunxi GR8.
Driver improvements:
- Drop default IRQ trigger types assigned during IRQ mapping on
AT91 and Nomadik. This error was identified by improvements in
the IRQ core by Marc Zyngier.
- Active high/low types on the GPIO IRQs for the ST pin
controller.
- IRQ support on GPIOs on the STM32 pin controller.
- Renesas Super-H/ARM sh-pfc: continued massive developments.
- Misc MXC improvements.
- SPDIF on the Allwiner A31 SoC
- IR remote and SPI NOR flash, NAND flash, I2C pins on the
AMLogic SoC.
- PWM pins on the Meson.
- Do not map unusable IRQs (taken by BIOS) on the Intel Cherryview.
- Add GPIO IRQ wakeup support to the Intel driver so we can wake up
from button pushes.
Deprecation:
- Deleted the obsolete STiH415/6 SoC support.
-----BEGIN PGP SIGNATURE-----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=APsF
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v4.9 cycle.
General improvements:
- nicer debugfs output with one pin/config pair per line.
- continued efforts to strictify module vs bool.
- constification and similar from Coccinelle engineers.
- return error from pinctrl_bind_pins()
- pulling in the ability to selectively disable mapping of unusable
IRQs from the GPIO subsystem.
New drivers:
- new driver for the Aspeed pin controller family: AST2400 (G4) and
AST2500 (G5) are supported. These are used by OpenBMC on the IBM
Witherspoon platform.
- new subdriver for the Allwinner sunxi GR8.
Driver improvements:
- drop default IRQ trigger types assigned during IRQ mapping on AT91
and Nomadik. This error was identified by improvements in the IRQ
core by Marc Zyngier.
- active high/low types on the GPIO IRQs for the ST pin controller.
- IRQ support on GPIOs on the STM32 pin controller.
- Renesas Super-H/ARM sh-pfc: continued massive developments.
- misc MXC improvements.
- SPDIF on the Allwiner A31 SoC
- IR remote and SPI NOR flash, NAND flash, I2C pins on the AMLogic
SoC.
- PWM pins on the Meson.
- do not map unusable IRQs (taken by BIOS) on the Intel Cherryview.
- add GPIO IRQ wakeup support to the Intel driver so we can wake up
from button pushes.
Deprecation:
- delete the obsolete STiH415/6 SoC support"
* tag 'pinctrl-v4.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (75 commits)
pinctrl: qcom: fix masking of pinmux functions
pinctrl: intel: Configure GPIO chip IRQ as wakeup interrupts
pinctrl: cherryview: Convert to use devm_gpiochip_add_data()
pinctrl: cherryview: Do not add all southwest and north GPIOs to IRQ domain
gpiolib: Make it possible to exclude GPIOs from IRQ domain
pinctrl: nomadik: don't default-flag IRQs as falling
pinctrl: st: Remove obsolete platforms from pinctrl-st dt doc
pinctrl: st: Remove STiH415/6 SoC pinctrl driver support.
pinctrl: amlogic: gxbb: add i2c pins
pinctrl: amlogic: gxbb: add nand pins
pinctrl: stm32: add IRQ_DOMAIN_HIERARCHY dependency
pinctrl: amlogic: gxbb: add spi nor pins
pinctrl: sh-pfc: r8a7794: Implement voltage switching for SDHI
pinctrl: sh-pfc: r8a7791: Implement voltage switching for SDHI
pinctrl: sh-pfc: Add PORT_GP_24 helper macro
pinctrl: Fix "st,syscfg" definition for STM32 pinctrl
driver: base: pinctrl: return error from pinctrl_bind_pins()
pinctrl: meson-gxbb: add the missing SDIO interrupt pin
pinctrl: aspeed: fix regmap error handling
pinctrl: mediatek: constify gpio_chip structures
...
Another quiet release, a few small extensions to the set of register
maps we support and an improvement in the debugfs code:
- Allow viewing of cached contents for write only registers via
debugfs.
- Support a wider range of read/write flag masks in register formats.
- Support more little endian formats.
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJX8x9EExxicm9vbmllQGtlcm5lbC5vcmcACgkQJNaLcl1Uh9Dc
mQf8Do/0T9bM0vTQFB9fcdOtYEa73vuDNbo0zCVAXEGJp862Z9OFB1oS5UInH9Os
T6gahxFR4tApv+89p9f7WGE2ppeiclkc9rpBdig6sBUtDGzF3+VT+N0LLV5I1TgA
FcYRFBXxewwk7qWywEd1IypRa6s2fazOqj7eYdqSpaFAyewpXMRKrnPNbtxbYDkx
MkIBADyT4ZfzOQQjxyff7vjVpWn8A41bD/ojhm9WLJL/Mxu/1q23nyTUYH7qqAAL
HC1DZFqUt2jbshmNozF9JlKuEGb1M2hXRptKLUJlynyVsnk2RO3OEUOW8haoxFBh
7Puxh+SsERDRHKiBkbFYnuBjLA==
=0fj2
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Another quiet release, a few small extensions to the set of register
maps we support and an improvement in the debugfs code:
- allow viewing of cached contents for write only registers via
debugfs.
- support a wider range of read/write flag masks in register formats.
- support more little endian formats"
* tag 'regmap-v4.9' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Add missing little endian functions
regmap: Allow longer flag masks for read and write
regmap: debugfs: Add support for dumping write only device registers
regmap: Add a function to check if a regmap register is cached
Here are the "big" driver core patches for 4.9-rc1. Also in here are a
number of debugfs fixes that cropped up due to the changes that happened
in 4.8 for that filesystem. Overall, nothing major, just a few fixes
and cleanups.
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iFYEABECABYFAlfyNw4PHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspLVYAoNXr
FXBHGb2tNT/1PLfvUCwd5PqWAJ9Khb5WAHtvjTmEN1zabz45aSbcrA==
=Uz6V
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here are the "big" driver core patches for 4.9-rc1. Also in here are a
number of debugfs fixes that cropped up due to the changes that
happened in 4.8 for that filesystem. Overall, nothing major, just a
few fixes and cleanups.
All of these have been in linux-next with no reported issues"
* tag 'driver-core-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (23 commits)
drivers: dma-coherent: Move spinlock in dma_alloc_from_coherent()
drivers: dma-coherent: Fix DMA coherent size for less than page
MAINTAINERS: extend firmware_class maintainer list
debugfs: propagate release() call result
driver-core: platform: Catch errors from calls to irq_get_irq_data
sysfs print name of undiscoverable attribute group
carl9170: fix debugfs crashes
b43legacy: fix debugfs crash
b43: fix debugfs crash
debugfs: introduce a public file_operations accessor
device core: Remove deprecated create_singlethread_workqueue
drivers/base dmam_declare_coherent_memory leaks
platform: don't return 0 from platform_get_irq[_byname]() on error
cpu: clean up register_cpu func
dma-mapping: use vma_pages().
drivers: dma-coherent: use vma_pages().
attribute_container: Fix typo
base: soc: make it explicitly non-modular
drivers: base: dma-mapping: page align the size when unmap_kernel_range
platform driver: fix use-after-free in platform_device_del()
...
Pull irq updates from Thomas Gleixner:
"The irq departement proudly presents:
- A rework of the core infrastructure to optimally spread interrupt
for multiqueue devices. The first version was a bit naive and
failed to take thread siblings and other details into account.
Developed in cooperation with Christoph and Keith.
- Proper delegation of softirqs to ksoftirqd, so if ksoftirqd is
active then no further softirq processsing on interrupt return
happens. Otherwise we try to delegate and still run another batch
of network packets in the irq return path, which then tries to
delegate to ksoftirqd .....
- A proper machine parseable sysfs based alternative for
/proc/interrupts.
- ACPI support for the GICV3-ITS and ARM interrupt remapping
- Two new irq chips from the ARM SoC zoo: STM32-EXTI and MVEBU-PIC
- A new irq chip for the JCore (SuperH)
- The usual pile of small fixlets in core and irqchip drivers"
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (42 commits)
softirq: Let ksoftirqd do its job
genirq: Make function __irq_do_set_handler() static
ARM/dts: Add EXTI controller node to stm32f429
ARM/STM32: Select external interrupts controller
drivers/irqchip: Add STM32 external interrupts support
Documentation/dt-bindings: Document STM32 EXTI controller bindings
irqchip/mips-gic: Use for_each_set_bit to iterate over local IRQs
pci/msi: Retrieve affinity for a vector
genirq/affinity: Remove old irq spread infrastructure
genirq/msi: Switch to new irq spreading infrastructure
genirq/affinity: Provide smarter irq spreading infrastructure
genirq/msi: Add cpumask allocation to alloc_msi_entry
genirq: Expose interrupt information through sysfs
irqchip/gicv3-its: Use MADT ITS subtable to do PCI/MSI domain initialization
irqchip/gicv3-its: Factor out PCI-MSI part that might be reused for ACPI
irqchip/gicv3-its: Probe ITS in the ACPI way
irqchip/gicv3-its: Refactor ITS DT init code to prepare for ACPI
irqchip/gicv3-its: Cleanup for ITS domain initialization
PCI/MSI: Setup MSI domain on a per-device basis using IORT ACPI table
ACPI: Add new IORT functions to support MSI domain handling
...
- Update of the ACPICA code in the kernel to upstream revision 20160831 with
the following major changes:
* New mechanism for GPE masking.
* Fixes for issues related to the LoadTable operator and table loading.
* Fixes for issues related to so-called module-level code (MLC), that is
AML that doesn't belong to any methods.
* Change of the return value of the _OSI method to reflect the Windows
behavior.
* GAS (Generic Address Structure) support fix related to 32-bit FADT
addresses.
* Elimination of unnecessary FADT version 2 support.
* ACPI tools fixes and cleanups.
From Bob Moore, Lv Zheng, and Jung-uk Kim.
- ACPI sysfs interface updates to fix GPE handling (on top of the new GPE
masking mechanism in ACPICA) and issues related to table loading (Lv Zheng).
- New watchdog driver based on the ACPI WDAT (ACPI Watchdog Action Table),
needed on some platforms to replace the iTCO watchdog that doesn't work there
and related updates of the intel_pmc_ipc, i2c/i801 and MFD/lcp_ich drivers
(Mika Westerberg).
- Driver core fix to prevent it from leaking secondary fwnode objects during
device removal (Lukas Wunner).
- New definitions of built-in properties for UART in ACPI-based x86 SoC drivers
and a 8250_dw driver quirk for the APM X-Gene SoC (Heikki Krogerus).
- New device ID for the Vulcan SPI controller and constification of local
strucures in the AMD SoC (APD) ACPI driver (Kamlakant Patel, Julia Lawall).
- Fix for a bug causing the allocation of PCI resorces to fail if
ACPI-enumerated child platform devices are registered below the PCI
devices in question (Mika Westerberg).
- Change of the default polarity for PCI legacy IRQs to high on systems
booting wth ACPI on platforms with a GIC interrupt controller model
fixing the discrepancy between the specification and HW behavior (Lorenzo
Pieralisi).
- Fixes for the handling of system suspend/resume in the ACPI EC driver and
update of that driver to make it cope with the cases when the EC device
defined in the ECDT has to be used throughout the entire system life cycle
(Lv Zheng).
- Update of the ACPI CPPC library to allow it to batch requests sent over the
PCC channel (to reduce overhead), to support the fixed functional hardware
(FFH) CPPC registers access type, to notify the mailbox framework about TX
completions when the interrupt flag is set for the PCC mailbox, and to
support HW-Reduced Communication Subspace type 2 (Ashwin Chaugule, Prashanth
Prakash, Srinivas Pandruvada, Hoan Tran).
- ACPI button driver fix and documentation update related to the handling of
laptop lids (Lv Zheng).
- ACPI battery driver initialization fix (Carlos Garnacho).
- ACPI GPIO enumeration documentation update (Mika Westerberg).
- Assorted updates of the core ACPI bus type code (Lukas Wunner, Lv Zheng).
- Assorted cleanups of the ACPI table parsing code and the x86-specific ACPI
code (Al Stone).
- Fixes for assorted ACPI-related issues found in linux-next (Wei Yongjun).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=xDOQ
-----END PGP SIGNATURE-----
Merge tag 'acpi-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"First off, the ACPICA code in the kernel is updated to upstream
revision 20160831 that brings in a few bug fixes and cleanups. In
particular, it is possible to mask GPEs now (and the sysfs interface
for GPE control is fixed on top of that), problems related to the
table loading mechanism are fixed and all code related to FADT version
2 (which has never been part of the ACPI specification) is dropped.
On the new features front, there is a new watchdog driver based on the
ACPI WDAT (ACPI Watchdog Action Table), needed on some platforms to
replace the iTCO watchdog that doesn't work there, and some UART
devices get new definitions of built-in properties (to be accessed via
the generic device properties API).
Also, included is a fix for an ACPI-related PCI resorces allocation
issue and a few problems in the EC driver and in the button and
battery drivers are fixed.
In addition to that, the ACPI CPPC library is updated to make batching
of requests sent over the PCC channel possible (which reduces the PCC
usage overhead substantially in some cases) and to support functional
fixed hardware (FFH) type of CPPC registers access (which will allow
CPPC to be used on x86 too in the future).
As usual, there are some assorted fixes and cleanups too.
Specifics:
- Update of the ACPICA code in the kernel to upstream revision
20160831 with the following major changes:
* New mechanism for GPE masking.
* Fixes for issues related to the LoadTable operator and table
loading.
* Fixes for issues related to so-called module-level code (MLC),
that is AML that doesn't belong to any methods.
* Change of the return value of the _OSI method to reflect the
Windows behavior.
* GAS (Generic Address Structure) support fix related to 32-bit
FADT addresses.
* Elimination of unnecessary FADT version 2 support.
* ACPI tools fixes and cleanups.
From Bob Moore, Lv Zheng, and Jung-uk Kim.
- ACPI sysfs interface updates to fix GPE handling (on top of the new
GPE masking mechanism in ACPICA) and issues related to table
loading (Lv Zheng).
- New watchdog driver based on the ACPI WDAT (ACPI Watchdog Action
Table), needed on some platforms to replace the iTCO watchdog that
doesn't work there and related updates of the intel_pmc_ipc,
i2c/i801 and MFD/lcp_ich drivers (Mika Westerberg).
- Driver core fix to prevent it from leaking secondary fwnode objects
during device removal (Lukas Wunner).
- New definitions of built-in properties for UART in ACPI-based x86
SoC drivers and a 8250_dw driver quirk for the APM X-Gene SoC
(Heikki Krogerus).
- New device ID for the Vulcan SPI controller and constification of
local strucures in the AMD SoC (APD) ACPI driver (Kamlakant Patel,
Julia Lawall).
- Fix for a bug causing the allocation of PCI resorces to fail if
ACPI-enumerated child platform devices are registered below the PCI
devices in question (Mika Westerberg).
- Change of the default polarity for PCI legacy IRQs to high on
systems booting wth ACPI on platforms with a GIC interrupt
controller model fixing the discrepancy between the specification
and HW behavior (Lorenzo Pieralisi).
- Fixes for the handling of system suspend/resume in the ACPI EC
driver and update of that driver to make it cope with the cases
when the EC device defined in the ECDT has to be used throughout
the entire system life cycle (Lv Zheng).
- Update of the ACPI CPPC library to allow it to batch requests sent
over the PCC channel (to reduce overhead), to support the fixed
functional hardware (FFH) CPPC registers access type, to notify the
mailbox framework about TX completions when the interrupt flag is
set for the PCC mailbox, and to support HW-Reduced Communication
Subspace type 2 (Ashwin Chaugule, Prashanth Prakash, Srinivas
Pandruvada, Hoan Tran).
- ACPI button driver fix and documentation update related to the
handling of laptop lids (Lv Zheng).
- ACPI battery driver initialization fix (Carlos Garnacho).
- ACPI GPIO enumeration documentation update (Mika Westerberg).
- Assorted updates of the core ACPI bus type code (Lukas Wunner, Lv
Zheng).
- Assorted cleanups of the ACPI table parsing code and the
x86-specific ACPI code (Al Stone).
- Fixes for assorted ACPI-related issues found in linux-next (Wei
Yongjun)"
* tag 'acpi-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (98 commits)
ACPI / documentation: Use recommended name in GPIO property names
watchdog: wdat_wdt: Fix warning for using 0 as NULL
watchdog: wdat_wdt: fix return value check in wdat_wdt_probe()
platform/x86: intel_pmc_ipc: Do not create iTCO watchdog when WDAT table exists
i2c: i801: Do not create iTCO watchdog when WDAT table exists
mfd: lpc_ich: Do not create iTCO watchdog when WDAT table exists
ACPI / bus: Adjust ACPI subsystem initialization for new table loading mode
ACPICA: Parser: Fix a regression in LoadTable support
ACPICA: Tables: Fix "UNLOAD" code path lock issues
ACPI / watchdog: Add support for WDAT hardware watchdog
ACPI / platform: Pay attention to parent device's resources
PCI: Add pci_find_resource()
ACPI / CPPC: Support PCC with interrupt flag
ACPI / sysfs: Update sysfs signature handling code
ACPI / sysfs: Fix an issue for LoadTable opcode
ACPICA: Tables: Fix a regression in acpi_tb_find_table()
ACPI / tables: Remove duplicated include from tables.c
ACPI / APD: constify local structures
x86: ACPI: make variable names clearer in acpi_parse_madt_lapic_entries()
x86: ACPI: remove extraneous white space after semicolon
...
* pm-domains:
PM / Domains: Rename pm_genpd_sync_poweron|poweroff()
PM / Domains: Don't measure latency of ->power_on|off() during system PM
PM / Domains: Remove redundant system PM callbacks
PM / Domains: Simplify detaching a device from its genpd
PM / Domains: Allow holes in genpd_data.domains array
PM / Domains: Add support for removing nested PM domains by provider
PM / Domains: Add support for removing PM domains
PM / Domains: Store the provider in the PM domain structure
PM / Domains: Prepare for adding support to remove PM domains
PM / Domains: Verify the PM domain is present when adding a provider
PM / Domains: Don't expose xlate and provider helper functions
PM / Domains: Don't expose generic_pm_domain structure to clients
staging: board: Remove calls to of_genpd_get_from_provider()
ARM: EXYNOS: Remove calls to of_genpd_get_from_provider()
PM / Domains: Add new helper functions for device-tree
PM / Domains: Always enable debugfs support if available
* device-properties:
serial: 8250_dw: Add quirk for APM X-Gene SoC
ACPI / LPSS: Provide build-in properties of the UART
ACPI / APD: Provide build-in properties of the UART
driver core: Don't leak secondary fwnode on device removal
We don't need to hold the spinlock while zeroing the allocated memory.
In case we handle big buffers this is a severe issue as other CPUs might
be spinning half a second or longer.
Signed-off-by: Bastian Hecht <bhecht@de.adit-jv.com>
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We fix a bug in dma_mmap_from_coherent() that appears when we map non page
aligned DMA memory. It cuts off the non aligned part (this is different to
dma_alloc_coherent() that always rounds up to full pages). So for mappings
of less than a page we get -ENXIO as dma_mmap_from_coherent() assumes we
want to map zero pages.
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Mark Craske <Mark_Craske@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
irq_get_irq_data() can return NULL, which results in a nasty crash.
Check its return value before passing it on to irqd_set_trigger_type().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The OPP framework allows each OPP to set a opp-supported-hw property
which provides values that are matched against supported_hw values
provided by the platform to limit support for certain OPPs on specific
hardware. Currently, if the platform does not set supported_hw values,
all OPPs are interpreted as supported, even if they have provided their
own opp-supported-hw values.
If an OPP has provided opp-supported-hw, it is indicating that there is
some specific hardware configuration it is supported by. These constraints
should be honored, and if no supported_hw has been provided by the
platform, there is no way to determine if that OPP is actually supported,
so it should be marked as not supported.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
These are internal static functions to genpd. Let's conform to the naming
rules, by dropping the "pm_" prefix from these.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Measure latency does by itself contribute to an increased latency, thus we
should avoid it when it isn't needed.
Currently genpd measures latencies in the system PM phase for the
->power_on|off() callbacks, except in the syscore case when it's not
allowed to use ktime_get() as timekeeping may be suspended.
Since there should be plenty of occasions during runtime PM to perform
these measurements, let's rely on that and drop them from system PM. This
will also make it consistent for how measurements are done of the runtime
PM callbacks (as those may be invoked during system PM).
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In cases when the PM domain haven't assigned a system PM callback, the PM
core fall-backs to check for the callback at the driver level instead.
This makes it redundant to assign a pm_generic_* helper function to a
corresponding system PM callback at a PM domain level.
Therefore, let's remove these assignments in pm_genpd_init().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There's no need to validate the PM domain by using genpd_lookup_dev() when
removing the device via genpd's genpd_dev_pm_detach() function. That's
because this function can't be called, unless there is a valid PM domain
for the device.
To simplify the behaviour, let's move code from pm_genpd_remove_device()
into a new internal function, genpd_remove_device(), which is called from
pm_genpd_remove_device() and genpd_dev_pm_detach().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Lina Iyer <lina.iyer@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
A fix for an issue with double locking that was introduced earlier this
release. I'd missed in review that we were already in a locked region
when trying to drop part of the cache.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJX5XcsAAoJECTWi3JdVIfQSfEH/iGoQHxcIyPeTBOk8XUIkmkJ
XgaQmZfj2RNKPbCug8KDhDks9qDL/w0/2DG00Trv6pVSFHyBKfX6AQEh0GgmYBJF
trsL1ai/F1dlUbrQaOGMkfUPSF3DvYRsM4/kJOxSruVYsK5PUk2zXEw9kPmquB57
K7IRru5KNDyH5p08h6jbm6po+0QhyaFnCi4iX5kqrvqPFWeP15KHfd+vuRNlWYt0
rf069yqHfZvPXDl6Alw+wdYskxDHT+hvmlWjIGVm1JwAmsx9V2QCDwrhBKG9aZW/
z+mdSKBSJ+RBIp7ucI8sSBm3JsxeSz4+teTe2DRZeGLJmnrZ6756xSNR0pphoAM=
=yYvs
-----END PGP SIGNATURE-----
Merge tag 'regmap-fix-v4.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"A fix for an issue with double locking that was introduced earlier
this release. I'd missed in review that we were already in a locked
region when trying to drop part of the cache"
* tag 'regmap-fix-v4.8-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: fix deadlock on _regmap_raw_write() error path
Commit 815806e39b ("regmap: drop cache if the bus transfer error")
added a call to regcache_drop_region() to error path in
_regmap_raw_write(). However that path runs with regmap lock taken,
and regcache_drop_region() tries to re-take it, causing a deadlock.
Fix that by calling map->cache_ops->drop() directly.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When CONFIG_OPTIMIZE_INLINING is set and we are building with -Wmaybe-uninitialized
enabled, we can get a warning for the opp core driver:
drivers/base/power/opp/core.c: In function 'dev_pm_opp_set_rate':
drivers/base/power/opp/core.c:560:8: warning: 'ou_volt_min' may be used uninitialized in this function [-Wmaybe-uninitialized]
This has only now appeared as a result of commit 797da5598f ("PM / devfreq:
Add COMPILE_TEST for build coverage"), which makes the driver visible in
some configurations that didn't have it before.
The warning is a false positive that I got with gcc-6.1.1, but there is
a simple workaround in removing the local variables that we get warnings
for (all three are affected depending on the configuration). This also
makes the code easier to read.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In platforms such as Rockchip's, the array of domains isn't always
filled without holes, as which domains are present depend on the
particular SoC revision.
By allowing holes to be in the array, such SoCs can still use a single
set of constants to index the array of power domains.
Fixes: 0159ec6707 (PM / Domains: Verify the PM domain is present when adding a provider)
Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This with the longer read and write masks allow supporting more
exotic devices. For example a little endian SPI device:
static const struct regmap_config foo_regmap_config = {
.reg_bits = 16,
.reg_stride = 4,
.val_bits = 16,
.write_flag_mask = 0x8000,
.reg_format_endian = REGMAP_ENDIAN_LITTLE,
.val_format_endian = REGMAP_ENDIAN_LITTLE,
...
};
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We currently only support masking the top bit for read and write
flags. Let's make the mask unsigned long and mask the bytes based
on the configured register length to make things more generic.
This allows using regmap for more exotic combinations like SPI
devices that need little endian addressing.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Further testing with false negatives suppressed by commit 293e2421fe
("rcu: Remove superfluous versions of rcu_read_lock_sched_held()")
identified a few more unprotected uses of RCU from the idle loop.
Because RCU actively ignores idle-loop code (for energy-efficiency
reasons, among other things), using RCU from the idle loop can result
in too-short grace periods, in turn resulting in arbitrary misbehavior.
The affected function is rpm_suspend().
The resulting lockdep-RCU splat is as follows:
------------------------------------------------------------------------
Warning from omap3
===============================
[ INFO: suspicious RCU usage. ]
4.6.0-rc5-next-20160426+ #1112 Not tainted
-------------------------------
include/trace/events/rpm.h:63 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 0
RCU used illegally from extended quiescent state!
1 lock held by swapper/0/0:
#0: (&(&dev->power.lock)->rlock){-.-...}, at: [<c052ee24>] __pm_runtime_suspend+0x54/0x84
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.6.0-rc5-next-20160426+ #1112
Hardware name: Generic OMAP36xx (Flattened Device Tree)
[<c0110308>] (unwind_backtrace) from [<c010c3a8>] (show_stack+0x10/0x14)
[<c010c3a8>] (show_stack) from [<c047fec8>] (dump_stack+0xb0/0xe4)
[<c047fec8>] (dump_stack) from [<c052d7b4>] (rpm_suspend+0x604/0x7e4)
[<c052d7b4>] (rpm_suspend) from [<c052ee34>] (__pm_runtime_suspend+0x64/0x84)
[<c052ee34>] (__pm_runtime_suspend) from [<c04bf3bc>] (omap2_gpio_prepare_for_idle+0x5c/0x70)
[<c04bf3bc>] (omap2_gpio_prepare_for_idle) from [<c01255e8>] (omap_sram_idle+0x140/0x244)
[<c01255e8>] (omap_sram_idle) from [<c0126b48>] (omap3_enter_idle_bm+0xfc/0x1ec)
[<c0126b48>] (omap3_enter_idle_bm) from [<c0601db8>] (cpuidle_enter_state+0x80/0x3d4)
[<c0601db8>] (cpuidle_enter_state) from [<c0183c74>] (cpu_startup_entry+0x198/0x3a0)
[<c0183c74>] (cpu_startup_entry) from [<c0b00c0c>] (start_kernel+0x354/0x3c8)
[<c0b00c0c>] (start_kernel) from [<8000807c>] (0x8000807c)
------------------------------------------------------------------------
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For irq spreading want to store affinity masks in the msi_entry. Add the
infrastructure for it.
We allocate an array of cpumasks with an array size of the number of used
vectors in the entry, so we can hand in the information per linux interrupt
later.
As we hand in the number of used vectors, we assign them right
away. Convert all the call sites.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: axboe@fb.com
Cc: keith.busch@intel.com
Cc: agordeev@redhat.com
Cc: linux-block@vger.kernel.org
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/1473862739-15032-2-git-send-email-hch@lst.de
strict pin controller returns -EINVAL in case of pin request which
is already claimed by somebody else.
Following is the sequence of calling pin_request() from
pinctrl_bind_pins():-
pinctrl_bind_pins()->pinctrl_select_state()->pinmux_enable_setting()->
pin_request()
But pinctrl_bind_pins() only returns -EPROBE_DEFER which makes device
driver probe successful even if the pin request is rejected by the pin
controller subsystem.
This commit modifies pinctrl_bind_pins() to return error if the pin is
rejected by pin control subsystem.
Signed-off-by: Deepak Das <deepak_das@mentor.com>
[Rewrote to be cleaner]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If a device supports PM domains that are subdomains of another PM
domain, then the PM domains should be removed in reverse order to
ensure that the subdomains are removed first. Furthermore, if there is
more than one provider, then there needs to be a way to remove the
domains in reverse order for a specific provider.
Add the function of_genpd_remove_last() to remove the last PM domain
added by a given PM domain provider and return the generic_pm_domain
structure for the PM domain that was removed.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The genpd framework allows users to add PM domains via the pm_genpd_init()
function, however, there is no corresponding function to remove a PM
domain. For most devices this may be fine as the PM domains are never
removed, however, for devices that wish to populate the PM domains from
within a driver, having the ability to remove a PM domain if the probing
of the device fails or the driver is unloaded is necessary.
Add the function pm_genpd_remove() to remove a PM domain by referencing
it's generic_pm_domain structure. Note that the bulk of the code that
removes the PM domain is placed in a separate local function
genpd_remove() (which is called by pm_genpd_remove()). The code is
structured in this way to prepare for adding another function to remove
a PM domain by provider that will also call genpd_remove(). Note that
users of genpd_remove() must call this function with the mutex,
gpd_list_lock, held.
PM domains can only be removed if the associated provider has been
removed, they are not a parent domain to another PM domain and have no
devices associated with them.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is possible that a device has more than one provider of PM domains
and to support the removal of a PM domain by provider, it is necessary
to store a reference to the provider in the PM domain structure.
Therefore, store a reference to the firmware node handle in the PM
domain structure and populate it when providers (only device-tree based
providers are currently supported by PM domains) are registered.
Please note that when removing PM domains, it is necessary to verify
that the PM domain provider has been removed from the list of providers
before the PM domain can be removed. To do this add another member to
the PM domain structure that indicates if the provider is present and
set this member accordingly when providers are added and removed.
Initialise the 'provider' and 'has_provider' members of the
generic_pm_domain structure when a PM domains is added by calling
pm_genpd_init().
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In order to remove PM domains safely from the list of PM domains,
it is necessary to adding locking for the PM domain list around any
places where devices or subdomains are added to a PM domain.
There are places where a reference to a PM domain is obtained via
calling of_genpd_get_from_provider() before adding the device or the
subdomain. In these cases a lock for the PM domain list needs to be
held around the call to of_genpd_get_from_provider() and the call to
add the device/subdomain. To avoid deadlocks by multiple attempts to
obtain the PM domain list lock, add functions genpd_add_device() and
genpd_add_subdomain() which require the user to hold the PM domain
list lock when calling.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When a PM domain provider is added, there is currently no way to tell if
any PM domains associated with the provider are present. Naturally, the
PM domain provider should not be registered if the PM domains have not
been added. Nonetheless, verify that the PM domain(s) associated with a
provider are present when registering the PM domain provider.
This change adds a dependency on the function pm_genpd_present() when
CONFIG_PM_GENERIC_DOMAINS_OF is enabled and so ensure this function is
available when CONFIG_PM_GENERIC_DOMAINS_OF selected.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Functions __of_genpd_xlate_simple(), __of_genpd_xlate_onecell() and
__of_genpd_add_provider() are not used outside of the core generic PM
domain code. Therefore, reduce the number of APIs exposed by making
these static. At the same time don't expose the typedef for
genpd_xlate_t either and make this a local definition as well.
The functions are renamed to follow the naming conventions for static
functions in the generic PM domain core.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There should be no need to expose the generic_pm_domain structure to
clients and this eliminates the need to implement reference counting for
any external reference to a PM domain. Therefore, make the functions
pm_genpd_lookup_dev() and of_genpd_get_from_provider() private to the
PM domain core. The functions are renamed in accordance with the naming
conventions for genpd static functions.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Ideally, if we are returning a reference to a PM domain via a call to
of_genpd_get_from_provider(), then we should keep track of such
references via a reference count. The reference count could then be used
to determine if a PM domain can be safely removed. Alternatively, it is
possible to avoid such external references by providing APIs to access
the PM domain and hence, eliminate any calls to
of_genpd_get_from_provider().
Add new helper functions for adding a device and a subdomain to a PM
domain when using device-tree, so that external calls to
of_genpd_get_from_provider() can be removed.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Several fixes here, the main one being the change from Lars-Peter which
I'd been letting soak in -next since the merge window in case it
uncovered further issues as it's a minimal fix rather than a change
addressing the root cause of the problems (which would've been too
invasive for -rc):
- The biggest change is a fix from Lars-Peter to ensure that we don't
create overlapping rbtree nodes which in turn avoids returning
corrupt cache values to users, fixing some issues that were exposed
by some recent optimisations with certain access patterns but had
been present for a long time.
- A fix from Elaine Zhang to stop us updating the cache if we get an
I/O error when writing to the hardware.
- A fix fromm Maarten ter Huurne to avoid uninitialized defaults in
cases where we have non-readable registers but are initializing the
cache by reading from the device.
-----BEGIN PGP SIGNATURE-----
iQEwBAABCAAaBQJXzrAXExxicm9vbmllQGtlcm5lbC5vcmcACgkQJNaLcl1Uh9DK
6Af/eRh/gD5Bp6DheOkrCNNj/jx0QlkAlgtkFzZBVp4AetirO3UZ3hwUyFCGyLWw
n2Ohmt54s3BHsvqy+YTrVD57AueI+chAOvKWJ6sYHxiPByy8KuVH+KmffhDHXjyd
gpIHPAMYnlYknTwitagbyWPA1vuAd4JWCqmJ7Nd/Fxl+Q9fY3PhsXSBXdcejWTtm
Su8XIhCtykTCTGijg4I/ZNeOLk1xPEWMiX+P/0knOpgE+9ATWq33UIWInoXe02bs
xITHse40BQUKCfoJKZjJGX3uSnluKpOvojIbcJhcHFYjJpeoU+4kj1Gd4UHMQ8vB
n8OpZYDKU3KdEHjIZBqbk0wFDw==
=cYjC
-----END PGP SIGNATURE-----
Merge tag 'regmap-fix-v4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"Several fixes here, the main one being the change from Lars-Peter
which I'd been letting soak in -next since the merge window in case it
uncovered further issues as it's a minimal fix rather than a change
addressing the root cause of the problems (which would've been too
invasive for -rc):
- The biggest change is a fix from Lars-Peter to ensure that we don't
create overlapping rbtree nodes which in turn avoids returning
corrupt cache values to users, fixing some issues that were exposed
by some recent optimisations with certain access patterns but had
been present for a long time.
- A fix from Elaine Zhang to stop us updating the cache if we get an
I/O error when writing to the hardware.
- A fix fromm Maarten ter Huurne to avoid uninitialized defaults in
cases where we have non-readable registers but are initializing the
cache by reading from the device"
* tag 'regmap-fix-v4.8-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: drop cache if the bus transfer error
regmap: rbtree: Avoid overlapping nodes
regmap: cache: Fix num_reg_defaults computation from reg_defaults_raw
The workqueue "deferred_wq" queues a single work item
&deferred_probe_work and hence doesn't require ordering.
It is involved in probing devices and is not being used on a memory
reclaim path. Hence, it has been converted to use system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
The work item has been flushed in driver_probe_done() to ensure that
there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dmam_declare_coherent_memory doesn't take into account the return
value of dma_declare_coherent_memory, which leads to incorrect resource
handling
Signed-off-by: Vyacheslav V. Yurkov <uvv.mail@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
of_irq_get[_byname]() return 0 iff irq_create_of_mapping() call fails.
Returning both error code and 0 on failure is a sign of a misdesigned API,
it makes the failure check unnecessarily complex and error prone. We should
rely on the platform IRQ resource in this case, not return 0, especially
as 0 can be a valid IRQ resource too...
Fixes: aff008ad81 ("platform_get_irq: Revert to platform_get_resource if of_irq_get fails")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch could reduce one branch in this function. Also
make the code more readble.
Signed-off-by: Alex Shi <alex.shi@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
To: linux-kernel@vger.kernel.org
To: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-pm@vger.kernel.org
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace explicit computation of vma page count by a call to
vma_pages()
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace explicit computation of vma page count by a call to
vma_pages()
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 't' in "function" was missing, this patch fixes this typo:
s/funcion/function/g
Signed-off-by: Xiubo Li <lixiubo@cmss.chinamobile.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
drivers/base/Kconfig:config SOC_BUS
drivers/base/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In platform_device_del(), the device is still used after a call to
device_del(). At this point there is no guarantee that the device is
still there and there could be a use-after-free access. Move the
call to device_remove_properties() before device_del() to fix that.
Signed-off-by: Jerome Marchand <jmarchan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In recent discussions on ksummit-discuss[1], it was suggested to do a
sequence of probe, remove, probe for testing driver remove paths. This
adds a kconfig option for said test.
[1] https://lists.linuxfoundation.org/pipermail/ksummit-discuss/2016-August/003459.html
Suggested-by: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The global mutex of 'gdp_mutex' is used to serialize creating/querying
glue dir and its cleanup. Turns out it isn't a perfect way because
part(kobj_kset_leave()) of the actual cleanup action() is done inside
the release handler of the glue dir kobject. That means gdp_mutex has
to be held before releasing the last reference count of the glue dir
kobject.
This patch moves glue dir's cleanup after kobject_del() in device_del()
for avoiding the race.
Cc: Yijing Wang <wangyijing@huawei.com>
Reported-by: Chandra Sekhar Lingutla <clingutla@codeaurora.org>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit appends a few _rcuidle suffixes to fix the following
RCU-used-from-idle bug:
> ===============================
> [ INFO: suspicious RCU usage. ]
> 4.6.0-rc5-next-20160426+ #1116 Not tainted
> -------------------------------
> include/trace/events/rpm.h:95 suspicious rcu_dereference_check() usage!
>
> other info that might help us debug this:
>
>
> RCU used illegally from idle CPU!
> rcu_scheduler_active = 1, debug_locks = 0
> RCU used illegally from extended quiescent state!
> 1 lock held by swapper/0/0:
> #0: (&(&dev->power.lock)->rlock){-.-...}, at: [<c052cc2c>] __rpm_callback+0x58/0x60
>
> stack backtrace:
> CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.6.0-rc5-next-20160426+ #1116
> Hardware name: Generic OMAP36xx (Flattened Device Tree)
> [<c0110290>] (unwind_backtrace) from [<c010c3a8>] (show_stack+0x10/0x14)
> [<c010c3a8>] (show_stack) from [<c047fd68>] (dump_stack+0xb0/0xe4)
> [<c047fd68>] (dump_stack) from [<c052d5d0>] (rpm_suspend+0x580/0x768)
> [<c052d5d0>] (rpm_suspend) from [<c052ec58>] (__pm_runtime_suspend+0x64/0x84)
> [<c052ec58>] (__pm_runtime_suspend) from [<c04bf25c>] (omap2_gpio_prepare_for_idle+0x5c/0x70)
> [<c04bf25c>] (omap2_gpio_prepare_for_idle) from [<c0125568>] (omap_sram_idle+0x140/0x244)
> [<c0125568>] (omap_sram_idle) from [<c01269dc>] (omap3_enter_idle_bm+0xfc/0x1ec)
> [<c01269dc>] (omap3_enter_idle_bm) from [<c0601bdc>] (cpuidle_enter_state+0x80/0x3d4)
> [<c0601bdc>] (cpuidle_enter_state) from [<c0183b08>] (cpu_startup_entry+0x198/0x3a0)
> [<c0183b08>] (cpu_startup_entry) from [<c0b00c0c>] (start_kernel+0x354/0x3c8)
> [<c0b00c0c>] (start_kernel) from [<8000807c>] (0x8000807c)
In the immortal words of Steven Rostedt, "*Whack* *Whack* *Whack*!!!"
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
WhACKED-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If device_add_property_set() is called for a device, a secondary fwnode
is allocated and assigned to the device but currently not freed once the
device is removed.
This can be triggered on Apple Macs if a Thunderbolt device is plugged
in on boot since Apple's NHI EFI driver sets a number of properties for
that device which are leaked on unplug.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
regmap_write
->_regmap_raw_write
-->regcache_write first and than use map->bus->write to wirte i2c or spi
But if the i2c or spi transfer failed, But the cache is updated, So if I use
regmap_read will get the cache data which is not the real register value.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Debugfs support for PM domains is only enabled if both CONFIG_PM_DEBUG
and CONFIG_PM_ADVANCED_DEBUG are enabled. CONFIG_PM_ADVANCED_DEBUG is
described as "extra PM attributes in sysfs for low-level
debugging/testing" which does not seem related.
Given that the debugfs for PM domains only allows users to view the
state of the PM domains, always enable debugfs support for PM domains
if PM domains and debugfs support is enabled.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add support for dumping write only device registers in debugfs. This is
useful for audio codecs that have write only registers (like WM8731).
The logic that decides if a value can be printed is moved to
regmap_printable() function to allow for easier future updates.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a function to check if a regmap register is cached. This will be used
in debugfs to dump the cached values of write only registers.
Signed-off-by: Cristian Birsan <cristian.birsan@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Prevent the low-level assembly hibernate code on x86-64 from
referring to __PAGE_OFFSET directly as a symbol which doesn't work
when the kernel identity mapping base is randomized, in which case
__PAGE_OFFSET is a variable (Rafael Wysocki).
- Avoid selecting CPU_FREQ_STAT by default as the statistics are not
required for proper cpufreq operation (Borislav Petkov).
- Add Skylake-X and Broadwell-X IDs to the intel_pstate's list of
processors where out-of-band (OBB) control of P-states is possible
and if that is in use, intel_pstate should not attempt to manage
P-states (Srinivas Pandruvada).
- Drop some unnecessary checks from the wakeup IRQ handling code in
the PM core (Markus Elfring).
- Reduce the number operating performance point (OPP) lookups in
one of the OPP framework's helper functions (Jisheng Zhang).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJXpKLNAAoJEILEb/54YlRx6L4P/39GR0kVB7vIyCajdWc4f3gh
0zh5RbKC0YT4F6upebzgQ9uYS9cv4y+df7ShVwKQAea3wDReEmZhM/egOGw0Ls+8
SS1MiJq1LSekyMIWH6cXwZsH69/V0LuWTBbzWYBgHUDbfEMlgwV5ZZMEH14/2bWw
d4SLUUiW5P42im+IDAxpdYneKOrbJo3txj6WbOutgtIrHdPko6lF1dDouKvI1QTk
zCBOkEB9nELq3rWN/sbPmHzbmbj/yFiiHk5+iqwuKKJZI8PQB9/C6Qmc3wvjtPpc
GXLPI+OHqLgBMofGsiKOvm3hPQAIjf/ERsUilHLE3qOi/Mi0qj7U4dFivZrPWaCG
j2bD+b36TffmG1r8L7NYbEKU60syeIFSRqAngbyswu6XF+NdVboaifENGcgM3tBC
pUC1mFh/4PMKP5zW9mOwE6WSntZkw14CVR+A3fRFOuTBavNvjGdckwLi/aBsZdU3
K4DJUFzdELF7+JdqnQV35yV2tgMbJhxQa/QBykiFBh3AyqliOZ8uBoIxxLinrGmH
XWR3kB4ZPRBIStGI9IpG3lNhLLU7mLIdaFhGayicicAwFcLsXN7oKWVzYfUqWA9T
1ptXApcRf6S9J1JnKHkznoQ1/D1pNYLbH+t7BOtWdK8SWBhMS2Lzo2kyKWsCFkJS
16J8j1tcLDhN1dvcBT55
=WvPB
-----END PGP SIGNATURE-----
Merge tag 'pm-extra-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"A few more fixes and cleanups in the x86-64 low-level hibernation
code, PM core, cpufreq (Kconfig and intel_pstate), and the operating
points framework.
Specifics:
- Prevent the low-level assembly hibernate code on x86-64 from
referring to __PAGE_OFFSET directly as a symbol which doesn't work
when the kernel identity mapping base is randomized, in which case
__PAGE_OFFSET is a variable (Rafael Wysocki).
- Avoid selecting CPU_FREQ_STAT by default as the statistics are not
required for proper cpufreq operation (Borislav Petkov).
- Add Skylake-X and Broadwell-X IDs to the intel_pstate's list of
processors where out-of-band (OBB) control of P-states is possible
and if that is in use, intel_pstate should not attempt to manage
P-states (Srinivas Pandruvada).
- Drop some unnecessary checks from the wakeup IRQ handling code in
the PM core (Markus Elfring).
- Reduce the number operating performance point (OPP) lookups in one
of the OPP framework's helper functions (Jisheng Zhang)"
* tag 'pm-extra-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
x86/power/64: Do not refer to __PAGE_OFFSET from assembly code
cpufreq: Do not default-yes CPU_FREQ_STAT
cpufreq: intel_pstate: Add more out-of-band IDs
PM / OPP: optimize dev_pm_opp_set_rate() performance a bit
PM-wakeup: Delete unnecessary checks before three function calls
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup rtc-cmos,
rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after shutdown for QNAP
TS-41x
- s3c: clock fixes
-----BEGIN PGP SIGNATURE-----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=rpGB
-----END PGP SIGNATURE-----
Merge tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"RTC for 4.8
Cleanups:
- huge cleanup of rtc-generic and char/genrtc this allowed to cleanup
rtc-cmos, rtc-sh, rtc-m68k, rtc-powerpc and rtc-parisc
- move mn10300 to rtc-cmos
Subsystem:
- fix wakealarms after hibernate
- multiples fixes for rctest
- simplify implementations of .read_alarm
New drivers:
- Maxim MAX6916
Drivers:
- ds1307: fix weekday
- m41t80: add wakeup support
- pcf85063: add support for PCF85063A variant
- rv8803: extend i2c fix and other fixes
- s35390a: fix alarm reading, this fixes instant reboot after
shutdown for QNAP TS-41x
- s3c: clock fixes"
* tag 'rtc-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (65 commits)
rtc: rv8803: Clear V1F when setting the time
rtc: rv8803: Stop the clock while setting the time
rtc: rv8803: Always apply the I²C workaround
rtc: rv8803: Fix read day of week
rtc: rv8803: Remove the check for valid time
rtc: rv8803: Kconfig: Indicate rx8900 support
rtc: asm9260: remove .owner field for driver
rtc: at91sam9: Fix missing spin_lock_init()
rtc: m41t80: add suspend handlers for alarm IRQ
rtc: m41t80: make it a real error message
rtc: pcf85063: Add support for the PCF85063A device
rtc: pcf85063: fix year range
rtc: hym8563: in .read_alarm set .tm_sec to 0 to signal minute accuracy
rtc: explicitly set tm_sec = 0 for drivers with minute accurancy
rtc: s3c: Add s3c_rtc_{enable/disable}_clk in s3c_rtc_setfreq()
rtc: s3c: Remove unnecessary call to disable already disabled clock
rtc: abx80x: use devm_add_action_or_reset()
rtc: m41t80: use devm_add_action_or_reset()
rtc: fix a typo and reduce three empty lines to one
rtc: s35390a: improve two comments in .set_alarm
...
* pm-sleep:
x86/power/64: Do not refer to __PAGE_OFFSET from assembly code
* pm-cpufreq:
cpufreq: Do not default-yes CPU_FREQ_STAT
cpufreq: intel_pstate: Add more out-of-band IDs
* pm-core:
PM-wakeup: Delete unnecessary checks before three function calls
* pm-opp:
PM / OPP: optimize dev_pm_opp_set_rate() performance a bit
When searching for a suitable node that should be used for inserting a new
register, which does not fall within the range of any existing node, we not
only looks for nodes which are directly adjacent to the new register, but
for nodes within a certain proximity. This is done to avoid creating lots
of small nodes with just a few registers spacing in between, which would
increase memory usage as well as tree traversal time.
This means there might be multiple node candidates which fall within the
proximity range of the new register. If we choose the first node we
encounter, under certain register insertion patterns it is possible to end
up with overlapping ranges. This will break order in the rbtree and can
cause the cached register value to become corrupted.
E.g. take the simplified example where the proximity range is 2 and the
register insertion sequence is 1, 4, 2, 3, 5.
* Insert of register 1 creates a new node, this is the root of the rbtree
* Insert of register 4 creates a new node, which is inserted to the right
of the root.
* Insert of register 2 gets inserted to the first node
* Insert of register 3 gets inserted to the first node
* Insert of register 5 also gets inserted into the first node since
this is the first node encountered and it is within the proximity range.
Now there are two overlapping nodes.
To avoid this always choose the node that is closest to the new register.
This will ensure that nodes will not overlap. The tree traversal is still
done as a binary search, we just don't stop at the first node found. So the
complexity of the algorithm stays within the same order.
Ideally if a new register is in the range of two adjacent blocks those
blocks should be merged, but that is a much more invasive change and left
for later.
The issue was initially introduced in commit 472fdec738 ("regmap: rbtree:
Reduce number of nodes, take 2"), but became much more exposed by commit
6399aea629 ("regmap: rbtree: When adding a reg do a bsearch for target
node") which changed the order in which nodes are looked-up.
Fixes: 6399aea629 ("regmap: rbtree: When adding a reg do a bsearch for target node")
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some systems are memory constrained but they need to load very large
firmwares. The firmware subsystem allows drivers to request this
firmware be loaded from the filesystem, but this requires that the
entire firmware be loaded into kernel memory first before it's provided
to the driver. This can lead to a situation where we map the firmware
twice, once to load the firmware into kernel memory and once to copy the
firmware into the final resting place.
This creates needless memory pressure and delays loading because we have
to copy from kernel memory to somewhere else. Let's add a
request_firmware_into_buf() API that allows drivers to request firmware
be loaded directly into a pre-allocated buffer. This skips the
intermediate step of allocating a buffer in kernel memory to hold the
firmware image while it's read from the filesystem. It also requires
that drivers know how much memory they'll require before requesting the
firmware and negates any benefits of firmware caching because the
firmware layer doesn't manage the buffer lifetime.
For a 16MB buffer, about half the time is spent performing a memcpy from
the buffer to the final resting place. I see loading times go from
0.081171 seconds to 0.047696 seconds after applying this patch. Plus
the vmalloc pressure is reduced.
This is based on a patch from Vikram Mulukutla on codeaurora.org:
https://www.codeaurora.org/cgit/quic/la/kernel/msm-3.18/commit/drivers/base/firmware_class.c?h=rel/msm-3.18&id=0a328c5f6cd999f5c591f172216835636f39bcb5
Link: http://lkml.kernel.org/r/20160607164741.31849-4-stephen.boyd@linaro.org
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Vikram Mulukutla <markivx@codeaurora.org>
Cc: Mark Brown <broonie@kernel.org>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some low memory systems with complex peripherals cannot afford to have
the relatively large firmware images taking up valuable memory during
suspend and resume. Change the internal implementation of
firmware_class to disallow caching based on a configurable option. In
the near future, variants of request_firmware will take advantage of
this feature.
Link: http://lkml.kernel.org/r/20160607164741.31849-3-stephen.boyd@linaro.org
[stephen.boyd@linaro.org: Drop firmware_desc design and use flags]
Signed-off-by: Vikram Mulukutla <markivx@codeaurora.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some systems are memory constrained but they need to load very large
firmwares. The firmware subsystem allows drivers to request this
firmware be loaded from the filesystem, but this requires that the
entire firmware be loaded into kernel memory first before it's provided
to the driver. This can lead to a situation where we map the firmware
twice, once to load the firmware into kernel memory and once to copy the
firmware into the final resting place.
This design creates needless memory pressure and delays loading because
we have to copy from kernel memory to somewhere else. This patch sets
adds support to the request firmware API to load the firmware directly
into a pre-allocated buffer, skipping the intermediate copying step and
alleviating memory pressure during firmware loading. The drawback is
that we can't use the firmware caching feature because the memory for
the firmware cache is not managed by the firmware layer.
This patch (of 3):
We use similar structured code to read and write the kmapped firmware
pages. The only difference is read copies from the kmap region and
write copies to it. Consolidate this into one function to reduce
duplication.
Link: http://lkml.kernel.org/r/20160607164741.31849-2-stephen.boyd@linaro.org
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Cc: Vikram Mulukutla <markivx@codeaurora.org>
Cc: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was only one use of __initdata_refok and __exit_refok
__init_refok was used 46 times against 82 for __ref.
Those definitions are obsolete since commit 312b1485fb ("Introduce new
section reference annotations tags: __ref, __refdata, __refconst")
This patch removes the following compatibility definitions and replaces
them treewide.
/* compatibility defines */
#define __init_refok __ref
#define __initdata_refok __refdata
#define __exit_refok __ref
I can also provide separate patches if necessary.
(One patch per tree and check in 1 month or 2 to remove old definitions)
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/1466796271-3043-1-git-send-email-fabf@skynet.be
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Majority of this update is about ASoC, including a few new drivers,
and the rest are mostly minor changes. The only substantial change in
ALSA core is about the additional error handling in the
compress-offload API. Below are highlights:
- Add the error propagating support in compress-offload API
- HD-audio: a usual Dell headset fixup, an Intel HDMI/DP fix, and the
default mixer setup change ot turn off the loopback
- Lots of updates for ASoC Intel drivers, mostly board support and bug
fixing, and to the NAU8825 driver
- Work on generalizing bits of simple-card to allow more code sharing
with the Renesas rsrc-card (which can't use simple-card due to DPCM)
- Removal of the Odroid X2 driver due to replacement with simple-card
- Support for several new Mediatek platforms and associated boards
- New ASoC drivers for Allwinner A10, Analog Devices ADAU7002, Broadcom
Cygnus, Cirrus Logic CS35L33 and CS53L30, Maxim MAX8960 and MAX98504,
Realtek RT5514 and Wolfson WM8758
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=zx3K
-----END PGP SIGNATURE-----
Merge tag 'sound-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"The majority of this update is about ASoC, including a few new
drivers, and the rest are mostly minor changes. The only substantial
change in ALSA core is about the additional error handling in the
compress-offload API. Below are highlights:
- Add the error propagating support in compress-offload API
- HD-audio: a usual Dell headset fixup, an Intel HDMI/DP fix, and the
default mixer setup change ot turn off the loopback
- Lots of updates for ASoC Intel drivers, mostly board support and
bug fixing, and to the NAU8825 driver
- Work on generalizing bits of simple-card to allow more code sharing
with the Renesas rsrc-card (which can't use simple-card due to DPCM)
- Removal of the Odroid X2 driver due to replacement with simple-card
- Support for several new Mediatek platforms and associated boards
- New ASoC drivers for Allwinner A10, Analog Devices ADAU7002,
Broadcom Cygnus, Cirrus Logic CS35L33 and CS53L30, Maxim MAX8960
and MAX98504, Realtek RT5514 and Wolfson WM8758"
* tag 'sound-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (278 commits)
sound: oss: Use kernel_read_file_from_path() for mod_firmware_load()
ASoC: Intel: Skylake: Delete an unnecessary check before the function call "release_firmware"
ASoC: Intel: Skylake: Fix NULL Pointer exception in dynamic_debug.
ASoC: samsung: Specify DMA channels through struct snd_dmaengine_pcm_config
ASoC: samsung: Fix error paths in the I2S driver's probe()
ASoC: cs53l30: Fix bit shift issue of TDM mode
ASoC: cs53l30: Fix a bug for TDM slot location validation
ASoC: rockchip: correct the spdif clk
ALSA: echoaudio: purge contradictions between dimension matrix members and total number of members
ASoC: rsrc-card: use asoc_simple_card_parse_card_name()
ASoC: rsrc-card: use asoc_simple_dai instead of rsrc_card_dai
ASoC: rsrc-card: use asoc_simple_card_parse_dailink_name()
ASoC: simple-card: use asoc_simple_card_parse_card_name()
ASoC: simple-card-utils: add asoc_simple_card_parse_card_name()
ASoC: simple-card: use asoc_simple_card_parse_dailink_name()
ASoC: simple-card-utils: add asoc_simple_card_set_dailink_name()
ASoC: nau8825: drop redundant idiom when converting integer to boolean
ASoC: nau8825: jack connection decision with different insertion logic
ASoC: mediatek: Add HDMI dai-links to the mt8173-rt5650 machine driver
ASoC: mediatek: mt2701: fix non static symbol warning
...
In 3245d460 (regmap: cache: Fall back to register by register read for
cache defaults) non-readable registers are skipped when initializing
reg_defaults, but are still included in num_reg_defaults. So there can
be uninitialized entries at the end of reg_defaults, which can cause
problems when the register cache initializes from the full array.
Fixed it by excluding non-readable registers from the count as well.
Signed-off-by: Maarten ter Huurne <maarten@treewalker.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently, NR_KERNEL_STACK tracks the number of kernel stacks in a zone.
This only makes sense if each kernel stack exists entirely in one zone,
and allowing vmapped stacks could break this assumption.
Since frv has THREAD_SIZE < PAGE_SIZE, we need to track kernel stack
allocations in a unit that divides both THREAD_SIZE and PAGE_SIZE on all
architectures. Keep it simple and use KiB.
Link: http://lkml.kernel.org/r/083c71e642c5fa5f1b6898902e1b2db7b48940d4.1468523549.git.luto@kernel.org
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Cc: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@kernel.org>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Vladimir Davydov <vdavydov@virtuozzo.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are now a number of accounting oddities such as mapped file pages
being accounted for on the node while the total number of file pages are
accounted on the zone. This can be coped with to some extent but it's
confusing so this patch moves the relevant file-based accounted. Due to
throttling logic in the page allocator for reliable OOM detection, it is
still necessary to track dirty and writeback pages on a per-zone basis.
[mgorman@techsingularity.net: fix NR_ZONE_WRITE_PENDING accounting]
Link: http://lkml.kernel.org/r/1468404004-5085-5-git-send-email-mgorman@techsingularity.net
Link: http://lkml.kernel.org/r/1467970510-21195-20-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
NR_FILE_PAGES is the number of file pages.
NR_FILE_MAPPED is the number of mapped file pages.
NR_ANON_PAGES is the number of mapped anon pages.
This is unhelpful naming as it's easy to confuse NR_FILE_MAPPED and
NR_ANON_PAGES for mapped pages. This patch renames NR_ANON_PAGES so we
have
NR_FILE_PAGES is the number of file pages.
NR_FILE_MAPPED is the number of mapped file pages.
NR_ANON_MAPPED is the number of mapped anon pages.
Link: http://lkml.kernel.org/r/1467970510-21195-19-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reclaim makes decisions based on the number of pages that are mapped but
it's mixing node and zone information. Account NR_FILE_MAPPED and
NR_ANON_PAGES pages on the node.
Link: http://lkml.kernel.org/r/1467970510-21195-18-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This moves the LRU lists from the zone to the node and related data such
as counters, tracing, congestion tracking and writeback tracking.
Unfortunately, due to reclaim and compaction retry logic, it is
necessary to account for the number of LRU pages on both zone and node
logic. Most reclaim logic is based on the node counters but the retry
logic uses the zone counters which do not distinguish inactive and
active sizes. It would be possible to leave the LRU counters on a
per-zone basis but it's a heavier calculation across multiple cache
lines that is much more frequent than the retry checks.
Other than the LRU counters, this is mostly a mechanical patch but note
that it introduces a number of anomalies. For example, the scans are
per-zone but using per-node counters. We also mark a node as congested
when a zone is congested. This causes weird problems that are fixed
later but is easier to review.
In the event that there is excessive overhead on 32-bit systems due to
the nodes being on LRU then there are two potential solutions
1. Long-term isolation of highmem pages when reclaim is lowmem
When pages are skipped, they are immediately added back onto the LRU
list. If lowmem reclaim persisted for long periods of time, the same
highmem pages get continually scanned. The idea would be that lowmem
keeps those pages on a separate list until a reclaim for highmem pages
arrives that splices the highmem pages back onto the LRU. It potentially
could be implemented similar to the UNEVICTABLE list.
That would reduce the skip rate with the potential corner case is that
highmem pages have to be scanned and reclaimed to free lowmem slab pages.
2. Linear scan lowmem pages if the initial LRU shrink fails
This will break LRU ordering but may be preferable and faster during
memory pressure than skipping LRU pages.
Link: http://lkml.kernel.org/r/1467970510-21195-4-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Rik van Riel <riel@surriel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patchset: "Move LRU page reclaim from zones to nodes v9"
This series moves LRUs from the zones to the node. While this is a
current rebase, the test results were based on mmotm as of June 23rd.
Conceptually, this series is simple but there are a lot of details.
Some of the broad motivations for this are;
1. The residency of a page partially depends on what zone the page was
allocated from. This is partially combatted by the fair zone allocation
policy but that is a partial solution that introduces overhead in the
page allocator paths.
2. Currently, reclaim on node 0 behaves slightly different to node 1. For
example, direct reclaim scans in zonelist order and reclaims even if
the zone is over the high watermark regardless of the age of pages
in that LRU. Kswapd on the other hand starts reclaim on the highest
unbalanced zone. A difference in distribution of file/anon pages due
to when they were allocated results can result in a difference in
again. While the fair zone allocation policy mitigates some of the
problems here, the page reclaim results on a multi-zone node will
always be different to a single-zone node.
it was scheduled on as a result.
3. kswapd and the page allocator scan zones in the opposite order to
avoid interfering with each other but it's sensitive to timing. This
mitigates the page allocator using pages that were allocated very recently
in the ideal case but it's sensitive to timing. When kswapd is allocating
from lower zones then it's great but during the rebalancing of the highest
zone, the page allocator and kswapd interfere with each other. It's worse
if the highest zone is small and difficult to balance.
4. slab shrinkers are node-based which makes it harder to identify the exact
relationship between slab reclaim and LRU reclaim.
The reason we have zone-based reclaim is that we used to have
large highmem zones in common configurations and it was necessary
to quickly find ZONE_NORMAL pages for reclaim. Today, this is much
less of a concern as machines with lots of memory will (or should) use
64-bit kernels. Combinations of 32-bit hardware and 64-bit hardware are
rare. Machines that do use highmem should have relatively low highmem:lowmem
ratios than we worried about in the past.
Conceptually, moving to node LRUs should be easier to understand. The
page allocator plays fewer tricks to game reclaim and reclaim behaves
similarly on all nodes.
The series has been tested on a 16 core UMA machine and a 2-socket 48
core NUMA machine. The UMA results are presented in most cases as the NUMA
machine behaved similarly.
pagealloc
---------
This is a microbenchmark that shows the benefit of removing the fair zone
allocation policy. It was tested uip to order-4 but only orders 0 and 1 are
shown as the other orders were comparable.
4.7.0-rc4 4.7.0-rc4
mmotm-20160623 nodelru-v9
Min total-odr0-1 490.00 ( 0.00%) 457.00 ( 6.73%)
Min total-odr0-2 347.00 ( 0.00%) 329.00 ( 5.19%)
Min total-odr0-4 288.00 ( 0.00%) 273.00 ( 5.21%)
Min total-odr0-8 251.00 ( 0.00%) 239.00 ( 4.78%)
Min total-odr0-16 234.00 ( 0.00%) 222.00 ( 5.13%)
Min total-odr0-32 223.00 ( 0.00%) 211.00 ( 5.38%)
Min total-odr0-64 217.00 ( 0.00%) 208.00 ( 4.15%)
Min total-odr0-128 214.00 ( 0.00%) 204.00 ( 4.67%)
Min total-odr0-256 250.00 ( 0.00%) 230.00 ( 8.00%)
Min total-odr0-512 271.00 ( 0.00%) 269.00 ( 0.74%)
Min total-odr0-1024 291.00 ( 0.00%) 282.00 ( 3.09%)
Min total-odr0-2048 303.00 ( 0.00%) 296.00 ( 2.31%)
Min total-odr0-4096 311.00 ( 0.00%) 309.00 ( 0.64%)
Min total-odr0-8192 316.00 ( 0.00%) 314.00 ( 0.63%)
Min total-odr0-16384 317.00 ( 0.00%) 315.00 ( 0.63%)
Min total-odr1-1 742.00 ( 0.00%) 712.00 ( 4.04%)
Min total-odr1-2 562.00 ( 0.00%) 530.00 ( 5.69%)
Min total-odr1-4 457.00 ( 0.00%) 433.00 ( 5.25%)
Min total-odr1-8 411.00 ( 0.00%) 381.00 ( 7.30%)
Min total-odr1-16 381.00 ( 0.00%) 356.00 ( 6.56%)
Min total-odr1-32 372.00 ( 0.00%) 346.00 ( 6.99%)
Min total-odr1-64 372.00 ( 0.00%) 343.00 ( 7.80%)
Min total-odr1-128 375.00 ( 0.00%) 351.00 ( 6.40%)
Min total-odr1-256 379.00 ( 0.00%) 351.00 ( 7.39%)
Min total-odr1-512 385.00 ( 0.00%) 355.00 ( 7.79%)
Min total-odr1-1024 386.00 ( 0.00%) 358.00 ( 7.25%)
Min total-odr1-2048 390.00 ( 0.00%) 362.00 ( 7.18%)
Min total-odr1-4096 390.00 ( 0.00%) 362.00 ( 7.18%)
Min total-odr1-8192 388.00 ( 0.00%) 363.00 ( 6.44%)
This shows a steady improvement throughout. The primary benefit is from
reduced system CPU usage which is obvious from the overall times;
4.7.0-rc4 4.7.0-rc4
mmotm-20160623nodelru-v8
User 189.19 191.80
System 2604.45 2533.56
Elapsed 2855.30 2786.39
The vmstats also showed that the fair zone allocation policy was definitely
removed as can be seen here;
4.7.0-rc3 4.7.0-rc3
mmotm-20160623 nodelru-v8
DMA32 allocs 28794729769 0
Normal allocs 48432501431 77227309877
Movable allocs 0 0
tiobench on ext4
----------------
tiobench is a benchmark that artifically benefits if old pages remain resident
while new pages get reclaimed. The fair zone allocation policy mitigates this
problem so pages age fairly. While the benchmark has problems, it is important
that tiobench performance remains constant as it implies that page aging
problems that the fair zone allocation policy fixes are not re-introduced.
4.7.0-rc4 4.7.0-rc4
mmotm-20160623 nodelru-v9
Min PotentialReadSpeed 89.65 ( 0.00%) 90.21 ( 0.62%)
Min SeqRead-MB/sec-1 82.68 ( 0.00%) 82.01 ( -0.81%)
Min SeqRead-MB/sec-2 72.76 ( 0.00%) 72.07 ( -0.95%)
Min SeqRead-MB/sec-4 75.13 ( 0.00%) 74.92 ( -0.28%)
Min SeqRead-MB/sec-8 64.91 ( 0.00%) 65.19 ( 0.43%)
Min SeqRead-MB/sec-16 62.24 ( 0.00%) 62.22 ( -0.03%)
Min RandRead-MB/sec-1 0.88 ( 0.00%) 0.88 ( 0.00%)
Min RandRead-MB/sec-2 0.95 ( 0.00%) 0.92 ( -3.16%)
Min RandRead-MB/sec-4 1.43 ( 0.00%) 1.34 ( -6.29%)
Min RandRead-MB/sec-8 1.61 ( 0.00%) 1.60 ( -0.62%)
Min RandRead-MB/sec-16 1.80 ( 0.00%) 1.90 ( 5.56%)
Min SeqWrite-MB/sec-1 76.41 ( 0.00%) 76.85 ( 0.58%)
Min SeqWrite-MB/sec-2 74.11 ( 0.00%) 73.54 ( -0.77%)
Min SeqWrite-MB/sec-4 80.05 ( 0.00%) 80.13 ( 0.10%)
Min SeqWrite-MB/sec-8 72.88 ( 0.00%) 73.20 ( 0.44%)
Min SeqWrite-MB/sec-16 75.91 ( 0.00%) 76.44 ( 0.70%)
Min RandWrite-MB/sec-1 1.18 ( 0.00%) 1.14 ( -3.39%)
Min RandWrite-MB/sec-2 1.02 ( 0.00%) 1.03 ( 0.98%)
Min RandWrite-MB/sec-4 1.05 ( 0.00%) 0.98 ( -6.67%)
Min RandWrite-MB/sec-8 0.89 ( 0.00%) 0.92 ( 3.37%)
Min RandWrite-MB/sec-16 0.92 ( 0.00%) 0.93 ( 1.09%)
4.7.0-rc4 4.7.0-rc4
mmotm-20160623 approx-v9
User 645.72 525.90
System 403.85 331.75
Elapsed 6795.36 6783.67
This shows that the series has little or not impact on tiobench which is
desirable and a reduction in system CPU usage. It indicates that the fair
zone allocation policy was removed in a manner that didn't reintroduce
one class of page aging bug. There were only minor differences in overall
reclaim activity
4.7.0-rc4 4.7.0-rc4
mmotm-20160623nodelru-v8
Minor Faults 645838 647465
Major Faults 573 640
Swap Ins 0 0
Swap Outs 0 0
DMA allocs 0 0
DMA32 allocs 46041453 44190646
Normal allocs 78053072 79887245
Movable allocs 0 0
Allocation stalls 24 67
Stall zone DMA 0 0
Stall zone DMA32 0 0
Stall zone Normal 0 2
Stall zone HighMem 0 0
Stall zone Movable 0 65
Direct pages scanned 10969 30609
Kswapd pages scanned 93375144 93492094
Kswapd pages reclaimed 93372243 93489370
Direct pages reclaimed 10969 30609
Kswapd efficiency 99% 99%
Kswapd velocity 13741.015 13781.934
Direct efficiency 100% 100%
Direct velocity 1.614 4.512
Percentage direct scans 0% 0%
kswapd activity was roughly comparable. There were differences in direct
reclaim activity but negligible in the context of the overall workload
(velocity of 4 pages per second with the patches applied, 1.6 pages per
second in the baseline kernel).
pgbench read-only large configuration on ext4
---------------------------------------------
pgbench is a database benchmark that can be sensitive to page reclaim
decisions. This also checks if removing the fair zone allocation policy
is safe
pgbench Transactions
4.7.0-rc4 4.7.0-rc4
mmotm-20160623 nodelru-v8
Hmean 1 188.26 ( 0.00%) 189.78 ( 0.81%)
Hmean 5 330.66 ( 0.00%) 328.69 ( -0.59%)
Hmean 12 370.32 ( 0.00%) 380.72 ( 2.81%)
Hmean 21 368.89 ( 0.00%) 369.00 ( 0.03%)
Hmean 30 382.14 ( 0.00%) 360.89 ( -5.56%)
Hmean 32 428.87 ( 0.00%) 432.96 ( 0.95%)
Negligible differences again. As with tiobench, overall reclaim activity
was comparable.
bonnie++ on ext4
----------------
No interesting performance difference, negligible differences on reclaim
stats.
paralleldd on ext4
------------------
This workload uses varying numbers of dd instances to read large amounts of
data from disk.
4.7.0-rc3 4.7.0-rc3
mmotm-20160623 nodelru-v9
Amean Elapsd-1 186.04 ( 0.00%) 189.41 ( -1.82%)
Amean Elapsd-3 192.27 ( 0.00%) 191.38 ( 0.46%)
Amean Elapsd-5 185.21 ( 0.00%) 182.75 ( 1.33%)
Amean Elapsd-7 183.71 ( 0.00%) 182.11 ( 0.87%)
Amean Elapsd-12 180.96 ( 0.00%) 181.58 ( -0.35%)
Amean Elapsd-16 181.36 ( 0.00%) 183.72 ( -1.30%)
4.7.0-rc4 4.7.0-rc4
mmotm-20160623 nodelru-v9
User 1548.01 1552.44
System 8609.71 8515.08
Elapsed 3587.10 3594.54
There is little or no change in performance but some drop in system CPU usage.
4.7.0-rc3 4.7.0-rc3
mmotm-20160623 nodelru-v9
Minor Faults 362662 367360
Major Faults 1204 1143
Swap Ins 22 0
Swap Outs 2855 1029
DMA allocs 0 0
DMA32 allocs 31409797 28837521
Normal allocs 46611853 49231282
Movable allocs 0 0
Direct pages scanned 0 0
Kswapd pages scanned 40845270 40869088
Kswapd pages reclaimed 40830976 40855294
Direct pages reclaimed 0 0
Kswapd efficiency 99% 99%
Kswapd velocity 11386.711 11369.769
Direct efficiency 100% 100%
Direct velocity 0.000 0.000
Percentage direct scans 0% 0%
Page writes by reclaim 2855 1029
Page writes file 0 0
Page writes anon 2855 1029
Page reclaim immediate 771 1628
Sector Reads 293312636 293536360
Sector Writes 18213568 18186480
Page rescued immediate 0 0
Slabs scanned 128257 132747
Direct inode steals 181 56
Kswapd inode steals 59 1131
It basically shows that kswapd was active at roughly the same rate in
both kernels. There was also comparable slab scanning activity and direct
reclaim was avoided in both cases. There appears to be a large difference
in numbers of inodes reclaimed but the workload has few active inodes and
is likely a timing artifact.
stutter
-------
stutter simulates a simple workload. One part uses a lot of anonymous
memory, a second measures mmap latency and a third copies a large file.
The primary metric is checking for mmap latency.
stutter
4.7.0-rc4 4.7.0-rc4
mmotm-20160623 nodelru-v8
Min mmap 16.6283 ( 0.00%) 13.4258 ( 19.26%)
1st-qrtle mmap 54.7570 ( 0.00%) 34.9121 ( 36.24%)
2nd-qrtle mmap 57.3163 ( 0.00%) 46.1147 ( 19.54%)
3rd-qrtle mmap 58.9976 ( 0.00%) 47.1882 ( 20.02%)
Max-90% mmap 59.7433 ( 0.00%) 47.4453 ( 20.58%)
Max-93% mmap 60.1298 ( 0.00%) 47.6037 ( 20.83%)
Max-95% mmap 73.4112 ( 0.00%) 82.8719 (-12.89%)
Max-99% mmap 92.8542 ( 0.00%) 88.8870 ( 4.27%)
Max mmap 1440.6569 ( 0.00%) 121.4201 ( 91.57%)
Mean mmap 59.3493 ( 0.00%) 42.2991 ( 28.73%)
Best99%Mean mmap 57.2121 ( 0.00%) 41.8207 ( 26.90%)
Best95%Mean mmap 55.9113 ( 0.00%) 39.9620 ( 28.53%)
Best90%Mean mmap 55.6199 ( 0.00%) 39.3124 ( 29.32%)
Best50%Mean mmap 53.2183 ( 0.00%) 33.1307 ( 37.75%)
Best10%Mean mmap 45.9842 ( 0.00%) 20.4040 ( 55.63%)
Best5%Mean mmap 43.2256 ( 0.00%) 17.9654 ( 58.44%)
Best1%Mean mmap 32.9388 ( 0.00%) 16.6875 ( 49.34%)
This shows a number of improvements with the worst-case outlier greatly
improved.
Some of the vmstats are interesting
4.7.0-rc4 4.7.0-rc4
mmotm-20160623nodelru-v8
Swap Ins 163 502
Swap Outs 0 0
DMA allocs 0 0
DMA32 allocs 618719206 1381662383
Normal allocs 891235743 564138421
Movable allocs 0 0
Allocation stalls 2603 1
Direct pages scanned 216787 2
Kswapd pages scanned 50719775 41778378
Kswapd pages reclaimed 41541765 41777639
Direct pages reclaimed 209159 0
Kswapd efficiency 81% 99%
Kswapd velocity 16859.554 14329.059
Direct efficiency 96% 0%
Direct velocity 72.061 0.001
Percentage direct scans 0% 0%
Page writes by reclaim 6215049 0
Page writes file 6215049 0
Page writes anon 0 0
Page reclaim immediate 70673 90
Sector Reads 81940800 81680456
Sector Writes 100158984 98816036
Page rescued immediate 0 0
Slabs scanned 1366954 22683
While this is not guaranteed in all cases, this particular test showed
a large reduction in direct reclaim activity. It's also worth noting
that no page writes were issued from reclaim context.
This series is not without its hazards. There are at least three areas
that I'm concerned with even though I could not reproduce any problems in
that area.
1. Reclaim/compaction is going to be affected because the amount of reclaim is
no longer targetted at a specific zone. Compaction works on a per-zone basis
so there is no guarantee that reclaiming a few THP's worth page pages will
have a positive impact on compaction success rates.
2. The Slab/LRU reclaim ratio is affected because the frequency the shrinkers
are called is now different. This may or may not be a problem but if it
is, it'll be because shrinkers are not called enough and some balancing
is required.
3. The anon/file reclaim ratio may be affected. Pages about to be dirtied are
distributed between zones and the fair zone allocation policy used to do
something very similar for anon. The distribution is now different but not
necessarily in any way that matters but it's still worth bearing in mind.
VM statistic counters for reclaim decisions are zone-based. If the kernel
is to reclaim on a per-node basis then we need to track per-node
statistics but there is no infrastructure for that. The most notable
change is that the old node_page_state is renamed to
sum_zone_node_page_state. The new node_page_state takes a pglist_data and
uses per-node stats but none exist yet. There is some renaming such as
vm_stat to vm_zone_stat and the addition of vm_node_stat and the renaming
of mod_state to mod_zone_state. Otherwise, this is mostly a mechanical
patch with no functional change. There is a lot of similarity between the
node and zone helpers which is unfortunate but there was no obvious way of
reusing the code and maintaining type safety.
Link: http://lkml.kernel.org/r/1467970510-21195-2-git-send-email-mgorman@techsingularity.net
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Rik van Riel <riel@surriel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Hillf Danton <hillf.zj@alibaba-inc.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Minchan Kim <minchan@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In dev_pm_opp_set_rate(), _find_opp_table() is called 4 times: once by
_get_opp_clk(), once by dev_pm_opp_set_rate() itself, and twice by
dev_pm_opp_find_freq_ceil(). If there are several opp_tables in the
system, three times of opp table finding is a big waste. This patch
reduced the call of _find_opp_table() to twice.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The following functions test whether their argument is NULL
and then return immediately.
* dev_pm_arm_wake_irq
* dev_pm_disarm_wake_irq
* wakeup_source_unregister
Thus the test around the calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Pavel Machek <pavel@ucw.cz>
[ rjw: Minor whitespace adjustments ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Merge updates from Andrew Morton:
- a few misc bits
- ocfs2
- most(?) of MM
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (125 commits)
thp: fix comments of __pmd_trans_huge_lock()
cgroup: remove unnecessary 0 check from css_from_id()
cgroup: fix idr leak for the first cgroup root
mm: memcontrol: fix documentation for compound parameter
mm: memcontrol: remove BUG_ON in uncharge_list
mm: fix build warnings in <linux/compaction.h>
mm, thp: convert from optimistic swapin collapsing to conservative
mm, thp: fix comment inconsistency for swapin readahead functions
thp: update Documentation/{vm/transhuge,filesystems/proc}.txt
shmem: split huge pages beyond i_size under memory pressure
thp: introduce CONFIG_TRANSPARENT_HUGE_PAGECACHE
khugepaged: add support of collapse for tmpfs/shmem pages
shmem: make shmem_inode_info::lock irq-safe
khugepaged: move up_read(mmap_sem) out of khugepaged_alloc_page()
thp: extract khugepaged from mm/huge_memory.c
shmem, thp: respect MADV_{NO,}HUGEPAGE for file mappings
shmem: add huge pages support
shmem: get_unmapped_area align huge page
shmem: prepare huge= mount option and sysfs knob
mm, rmap: account shmem thp pages
...
Several small updates and API enhancements:
- Provide transparent unrolling of bulk writes into individual writes
so they can be used with devices without raw formatting.
- Fix compatibility between I2C controllers supporting block commands
and devices with more than 8 bit wide registers.
- Add some helpers for iopoll-like functionality and workarounds for
weird interrupt controllers.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXljTLAAoJECTWi3JdVIfQMSMH/1MRirJkwIds0SRbWcnG9hOe
nMfUhkuFuCZJN82GwOh7YbAxLB1pGXKsGZq1XGMYFvwJawEizR3o83fgcRy1LQmG
KOQHO1O/CWQqRo1ntGl33H2thhq6e67y6lpeMBhdMvp3VjqdyzlILNSva6iWbW/R
N0iFSSKd4VdHlg/o+R3k7EzWCLZ4FZI7B9/5OjxWkoUR+tloNI8rR8Ecwl6+Q37K
8+yo6R0Ntx/JXB7JvA5Y8vqPdUGi68+XpcnaAcpM5DaL95+lqzduWCjKfjG5oatZ
3o/ORRVi+WyD95/NLXwKFMvSDSGokVDrU87HNgKph+f4sNF5TIoC/E+JhPUQBSU=
=7BlM
-----END PGP SIGNATURE-----
Merge tag 'regmap-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap updates from Mark Brown:
"Several small updates and API enhancements:
- provide transparent unrolling of bulk writes into individual writes
so they can be used with devices without raw formatting.
- fix compatibility between I2C controllers supporting block commands
and devices with more than 8 bit wide registers.
- add some helpers for iopoll-like functionality and workarounds for
weird interrupt controllers"
* tag 'regmap-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: add iopoll-like polling macro
regmap: Support bulk writes for devices without raw formatting
regmap-i2c: Use i2c block command only if register value width is 8 bit
regmap: irq: Add support to call client specific pre/post interrupt service
regmap: Add file patterns for regmap device tree bindings
- Rework the cpufreq governor interface to make it more straightforward
and modify the conservative governor to avoid using transition
notifications (Rafael Wysocki).
- Rework the handling of frequency tables by the cpufreq core to make
it more efficient (Viresh Kumar).
- Modify the schedutil governor to reduce the number of wakeups it
causes to occur in cases when the CPU frequency doesn't need to be
changed (Steve Muckle, Viresh Kumar).
- Fix some minor issues and clean up code in the cpufreq core and
governors (Rafael Wysocki, Viresh Kumar).
- Add Intel Broxton support to the intel_pstate driver (Srinivas
Pandruvada).
- Fix problems related to the config TDP feature and to the validity
of the MSR_HWP_INTERRUPT register in intel_pstate (Jan Kiszka,
Srinivas Pandruvada).
- Make intel_pstate update the cpu_frequency tracepoint even if
the frequency doesn't change to avoid confusing powertop (Rafael
Wysocki).
- Clean up the usage of __init/__initdata in intel_pstate, mark some
of its internal variables as __read_mostly and drop an unused
structure element from it (Jisheng Zhang, Carsten Emde).
- Clean up the usage of some duplicate MSR symbols in intel_pstate
and turbostat (Srinivas Pandruvada).
- Update/fix the powernv, s3c24xx and mvebu cpufreq drivers (Akshay
Adiga, Viresh Kumar, Ben Dooks).
- Fix a regression (introduced during the 4.5 cycle) in the
pcc-cpufreq driver by reverting the problematic commit (Andreas
Herrmann).
- Add support for Intel Denverton to intel_idle, clean up Broxton
support in it and make it explicitly non-modular (Jacob Pan,
Jan Beulich, Paul Gortmaker).
- Add support for Denverton and Ivy Bridge server to the Intel RAPL
power capping driver and make it more careful about the handing
of MSRs that may not be present (Jacob Pan, Xiaolong Wang).
- Fix resume from hibernation on x86-64 by making the CPU offline
during resume avoid using MONITOR/MWAIT in the "play dead" loop
which may lead to an inadvertent "revival" of a "dead" CPU and
a page fault leading to a kernel crash from it (Rafael Wysocki).
- Make memory management during resume from hibernation more
straightforward (Rafael Wysocki).
- Add debug features that should help to detect problems related
to hibernation and resume from it (Rafael Wysocki, Chen Yu).
- Clean up hibernation core somewhat (Rafael Wysocki).
- Prevent KASAN from instrumenting the hibernation core which leads
to large numbers of false-positives from it (James Morse).
- Prevent PM (hibernate and suspend) notifiers from being called
during the cleanup phase if they have not been called during the
corresponding preparation phase which is possible if one of the
other notifiers returns an error at that time (Lianwei Wang).
- Improve suspend-related debug printout in the tasks freezer and
clean up suspend-related console handling (Roger Lu, Borislav
Petkov).
- Update the AnalyzeSuspend script in the kernel sources to
version 4.2 (Todd Brandt).
- Modify the generic power domains framework to make it handle
system suspend/resume better (Ulf Hansson).
- Make the runtime PM framework avoid resuming devices synchronously
when user space changes the runtime PM settings for them and
improve its error reporting (Rafael Wysocki, Linus Walleij).
- Fix error paths in devfreq drivers (exynos, exynos-ppmu, exynos-bus)
and in the core, make some devfreq code explicitly non-modular and
change some of it into tristate (Bartlomiej Zolnierkiewicz,
Peter Chen, Paul Gortmaker).
- Add DT support to the generic PM clocks management code and make
it export some more symbols (Jon Hunter, Paul Gortmaker).
- Make the PCI PM core code slightly more robust against possible
driver errors (Andy Shevchenko).
- Make it possible to change DESTDIR and PREFIX in turbostat
(Andy Shevchenko).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=uVGz
-----END PGP SIGNATURE-----
Merge tag 'pm-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"Again, the majority of changes go into the cpufreq subsystem, but
there are no big features this time. The cpufreq changes that stand
out somewhat are the governor interface rework and improvements
related to the handling of frequency tables. Apart from those, there
are fixes and new device/CPU IDs in drivers, cleanups and an
improvement of the new schedutil governor.
Next, there are some changes in the hibernation core, including a fix
for a nasty problem related to the MONITOR/MWAIT usage by CPU offline
during resume from hibernation, a few core improvements related to
memory management during resume, a couple of additional debug features
and cleanups.
Finally, we have some fixes and cleanups in the devfreq subsystem,
generic power domains framework improvements related to system
suspend/resume, support for some new chips in intel_idle and in the
power capping RAPL driver, a new version of the AnalyzeSuspend utility
and some assorted fixes and cleanups.
Specifics:
- Rework the cpufreq governor interface to make it more
straightforward and modify the conservative governor to avoid using
transition notifications (Rafael Wysocki).
- Rework the handling of frequency tables by the cpufreq core to make
it more efficient (Viresh Kumar).
- Modify the schedutil governor to reduce the number of wakeups it
causes to occur in cases when the CPU frequency doesn't need to be
changed (Steve Muckle, Viresh Kumar).
- Fix some minor issues and clean up code in the cpufreq core and
governors (Rafael Wysocki, Viresh Kumar).
- Add Intel Broxton support to the intel_pstate driver (Srinivas
Pandruvada).
- Fix problems related to the config TDP feature and to the validity
of the MSR_HWP_INTERRUPT register in intel_pstate (Jan Kiszka,
Srinivas Pandruvada).
- Make intel_pstate update the cpu_frequency tracepoint even if the
frequency doesn't change to avoid confusing powertop (Rafael
Wysocki).
- Clean up the usage of __init/__initdata in intel_pstate, mark some
of its internal variables as __read_mostly and drop an unused
structure element from it (Jisheng Zhang, Carsten Emde).
- Clean up the usage of some duplicate MSR symbols in intel_pstate
and turbostat (Srinivas Pandruvada).
- Update/fix the powernv, s3c24xx and mvebu cpufreq drivers (Akshay
Adiga, Viresh Kumar, Ben Dooks).
- Fix a regression (introduced during the 4.5 cycle) in the
pcc-cpufreq driver by reverting the problematic commit (Andreas
Herrmann).
- Add support for Intel Denverton to intel_idle, clean up Broxton
support in it and make it explicitly non-modular (Jacob Pan, Jan
Beulich, Paul Gortmaker).
- Add support for Denverton and Ivy Bridge server to the Intel RAPL
power capping driver and make it more careful about the handing of
MSRs that may not be present (Jacob Pan, Xiaolong Wang).
- Fix resume from hibernation on x86-64 by making the CPU offline
during resume avoid using MONITOR/MWAIT in the "play dead" loop
which may lead to an inadvertent "revival" of a "dead" CPU and a
page fault leading to a kernel crash from it (Rafael Wysocki).
- Make memory management during resume from hibernation more
straightforward (Rafael Wysocki).
- Add debug features that should help to detect problems related to
hibernation and resume from it (Rafael Wysocki, Chen Yu).
- Clean up hibernation core somewhat (Rafael Wysocki).
- Prevent KASAN from instrumenting the hibernation core which leads
to large numbers of false-positives from it (James Morse).
- Prevent PM (hibernate and suspend) notifiers from being called
during the cleanup phase if they have not been called during the
corresponding preparation phase which is possible if one of the
other notifiers returns an error at that time (Lianwei Wang).
- Improve suspend-related debug printout in the tasks freezer and
clean up suspend-related console handling (Roger Lu, Borislav
Petkov).
- Update the AnalyzeSuspend script in the kernel sources to version
4.2 (Todd Brandt).
- Modify the generic power domains framework to make it handle system
suspend/resume better (Ulf Hansson).
- Make the runtime PM framework avoid resuming devices synchronously
when user space changes the runtime PM settings for them and
improve its error reporting (Rafael Wysocki, Linus Walleij).
- Fix error paths in devfreq drivers (exynos, exynos-ppmu,
exynos-bus) and in the core, make some devfreq code explicitly
non-modular and change some of it into tristate (Bartlomiej
Zolnierkiewicz, Peter Chen, Paul Gortmaker).
- Add DT support to the generic PM clocks management code and make it
export some more symbols (Jon Hunter, Paul Gortmaker).
- Make the PCI PM core code slightly more robust against possible
driver errors (Andy Shevchenko).
- Make it possible to change DESTDIR and PREFIX in turbostat (Andy
Shevchenko)"
* tag 'pm-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (89 commits)
Revert "cpufreq: pcc-cpufreq: update default value of cpuinfo_transition_latency"
PM / hibernate: Introduce test_resume mode for hibernation
cpufreq: export cpufreq_driver_resolve_freq()
cpufreq: Disallow ->resolve_freq() for drivers providing ->target_index()
PCI / PM: check all fields in pci_set_platform_pm()
cpufreq: acpi-cpufreq: use cached frequency mapping when possible
cpufreq: schedutil: map raw required frequency to driver frequency
cpufreq: add cpufreq_driver_resolve_freq()
cpufreq: intel_pstate: Check cpuid for MSR_HWP_INTERRUPT
intel_pstate: Update cpu_frequency tracepoint every time
cpufreq: intel_pstate: clean remnant struct element
PM / tools: scripts: AnalyzeSuspend v4.2
x86 / hibernate: Use hlt_play_dead() when resuming from hibernation
cpufreq: powernv: Replacing pstate_id with frequency table index
intel_pstate: Fix MSR_CONFIG_TDP_x addressing in core_get_max_pstate()
PM / hibernate: Image data protection during restoration
PM / hibernate: Add missing braces in __register_nosave_region()
PM / hibernate: Clean up comments in snapshot.c
PM / hibernate: Clean up function headers in snapshot.c
PM / hibernate: Add missing braces in hibernate_setup()
...
Let's add ShmemHugePages and ShmemPmdMapped fields into meminfo and
smaps. It indicates how many times we allocate and map shmem THP.
NR_ANON_TRANSPARENT_HUGEPAGES is renamed to NR_ANON_THPS.
Link: http://lkml.kernel.org/r/1466021202-61880-27-git-send-email-kirill.shutemov@linux.intel.com
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since zone_can_shift() is being used to validate the target zone during
onlining, it should also be used to determine the content of
valid_zones.
Link: http://lkml.kernel.org/r/1462816419-4479-4-git-send-email-arbab@linux.vnet.ibm.com
Signed-off-by: Reza Arbab <arbab@linux.vnet.ibm.com>
Reviewd-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Daniel Kiper <daniel.kiper@oracle.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Tang Chen <tangchen@cn.fujitsu.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Andrew Banman <abanman@sgi.com>
Cc: Chen Yucong <slaoub@gmail.com>
Cc: Yasunori Goto <y-goto@jp.fujitsu.com>
Cc: Zhang Zhen <zhenzhang.zhang@huawei.com>
Cc: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull s390 updates from Martin Schwidefsky:
"There are a couple of new things for s390 with this merge request:
- a new scheduling domain "drawer" is added to reflect the unusual
topology found on z13 machines. Performance tests showed up to 8
percent gain with the additional domain.
- the new crc-32 checksum crypto module uses the vector-galois-field
multiply and sum SIMD instruction to speed up crc-32 and crc-32c.
- proper __ro_after_init support, this requires RO_AFTER_INIT_DATA in
the generic vmlinux.lds linker script definitions.
- kcov instrumentation support. A prerequisite for that is the
inline assembly basic block cleanup, which is the reason for the
net/iucv/iucv.c change.
- support for 2GB pages is added to the hugetlbfs backend.
Then there are two removals:
- the oprofile hardware sampling support is dead code and is removed.
The oprofile user space uses the perf interface nowadays.
- the ETR clock synchronization is removed, this has been superseeded
be the STP clock synchronization. And it always has been
"interesting" code..
And the usual bug fixes and cleanups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (82 commits)
s390/pci: Delete an unnecessary check before the function call "pci_dev_put"
s390/smp: clean up a condition
s390/cio/chp : Remove deprecated create_singlethread_workqueue
s390/chsc: improve channel path descriptor determination
s390/chsc: sanitize fmt check for chp_desc determination
s390/cio: make fmt1 channel path descriptor optional
s390/chsc: fix ioctl CHSC_INFO_CU command
s390/cio/device_ops: fix kernel doc
s390/cio: allow to reset channel measurement block
s390/console: Make preferred console handling more consistent
s390/mm: fix gmap tlb flush issues
s390/mm: add support for 2GB hugepages
s390: have unique symbol for __switch_to address
s390/cpuinfo: show maximum thread id
s390/ptrace: clarify bits in the per_struct
s390: stack address vs thread_info
s390: remove pointless load within __switch_to
s390: enable kcov support
s390/cpumf: use basic block for ecctr inline assembly
s390/hypfs: use basic block for diag inline assembly
...
* pm-core:
PM / runtime: Asynchronous "idle" in pm_runtime_allow()
PM / runtime: print error when activating a child to unactive parent
* pm-clk:
PM / clk: Add support for adding a specific clock from device-tree
PM / clk: export symbols for existing pm_clk_<...> API fcns
* pm-domains:
PM / Domains: Convert pm_genpd_init() to return an error code
PM / Domains: Stop/start devices during system PM suspend/resume in genpd
PM / Domains: Allow runtime PM during system PM phases
PM / Runtime: Avoid resuming devices again in pm_runtime_force_resume()
PM / Domains: Remove redundant pm_request_idle() call in genpd
PM / Domains: Remove redundant wrapper functions for system PM
PM / Domains: Allow genpd to power on during system PM phases
* pm-pci:
PCI / PM: check all fields in pci_set_platform_pm()
Arjan reports that it takes a relatively long time to enable runtime
PM for multiple devices at system startup, because all writes to the
"control" attribute in sysfs are handled synchronously and if the
device is suspended as a result of the write, it will block until
that operation is complete.
That may be avoided by passing the RPM_ASYNC flag to rpm_idle()
in pm_runtime_allow() which will make it execute the device's
"idle" callback asynchronously, so writes to "control" changing
it from "on" to "auto" will return without waiting.
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
When doing a bulk writes from a device which lacks raw I/O support we
fall back to doing register at a time reads but we still use the raw
formatters in order to render the data into the word size used by the
device (since bulk reads still operate on the device word size rather
than unsigned ints). This means that devices without raw formatting
such as those that provide reg_read() are not supported. Provide
handling for them by copying the values read into native endian values
of the appropriate size.
This complements commit d5b98eb124 ("regmap: Support bulk reads for
devices without raw formatting").
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The are already cases when pm_genpd_init() can fail. Currently we hide the
failures instead of propagating an error code, which is a better method.
Moreover, to prepare for future changes like moving away from using a
fixed array-size of the struct genpd_power_state, to instead dynamically
allocate data for it, the pm_genpd_init() API needs to be able to return
an error code, as allocation can fail.
Current users of the pm_genpd_init() is thus requested to start dealing
with error codes. In the transition phase, users will have to live with
only error messages being printed to log.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Some drivers using the PM clocks framework need to add specific clocks
from device-tree using a name by calling the functions
of_clk_get_by_name() and then pm_clk_add_clk(). Rather than having
drivers call both functions, add a helper function of_pm_clk_add_clk()
that will call these functions so drivers can call a single function
to add a specific clock from device-tree.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The code currently silently bails out with -EBUSY if you try to
activate a child to an inactive parent.
This typically happens when you have a runtime suspended parent
and runtime resume your child, but forgot to set .ignore_children
on the parent to true with pm_suspend_ignore_children(dev).
Silently ignoring this error is not good as it gives rise to
other strange behaviour like double-resume of devices after
silently bailing out of the .runtime_resume() callback.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
For device nodes in both DT and ACPI, it possible to have named
child nodes which contain properties (an existing example being
gpio-leds). This adds a function to find a named child node for
a device which can be used by drivers for property retrieval.
For DT data node name matching, of_node_cmp() and similar functions
are made available outside of CONFIG_OF block so the new function
can reference these for DT and non-DT builds.
For ACPI data node name matching, a helper function is also added
which returns false if CONFIG_ACPI is not set, otherwise it
performs a string comparison on the data node name. This avoids
using the acpi_data_node struct for non CONFIG_ACPI builds,
which would otherwise cause a build failure.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Acked-by: Sathyanarayana Nujella <sathyanarayana.nujella@intel.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Chips with 16-bit registers don't usually work well with I2C block
commands. For example, neither the LM75 datasheet nor the TMP102 datasheet
mentions block command support, and in fact it does not work for any of
those chips. Also, it is not clear how the block command would handle
16-bit SMBus operations in the fist place, since the data format associated
with those commands is either little endian or big endian, which requires
some kind of conversion to or from host byte order.
Only use i2c block commands if both register and value width is 8 bit.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Here are a small number of debugfs, ISA, and one driver core fix for 4.7-rc4.
All of these resolve reported issues. The ISA ones have spent the least
amount of time in linux-next, sorry about that, I didn't realize they
were regressions that needed to get in now (thanks to Thorsten for the
prodding!) but they do all pass the 0-day bot tests. The others have
been in linux-next for a while now.
Full details about them are in the shortlog below.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAldlbeQACgkQMUfUDdst+ymnFACfaWhEKA/84jwNNHiim92diJrY
zYsAoLOmpBw68yL6qTSZbcWJF4Flb6Xk
=N8M2
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are a small number of debugfs, ISA, and one driver core fix for
4.7-rc4.
All of these resolve reported issues. The ISA ones have spent the
least amount of time in linux-next, sorry about that, I didn't realize
they were regressions that needed to get in now (thanks to Thorsten
for the prodding!) but they do all pass the 0-day bot tests. The
others have been in linux-next for a while now.
Full details about them are in the shortlog below"
* tag 'driver-core-4.7-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
isa: Dummy isa_register_driver should return error code
isa: Call isa_bus_init before dependent ISA bus drivers register
watchdog: ebc-c384_wdt: Allow build for X86_64
iio: stx104: Allow build for X86_64
gpio: Allow PC/104 devices on X86_64
isa: Allow ISA-style drivers on modern systems
base: make module_create_drivers_dir race-free
debugfs: open_proxy_open(): avoid double fops release
debugfs: full_proxy_open(): free proxy on ->open() failure
kernel/kcov: unproxify debugfs file's fops
The isa_bus_init function must be called before drivers which utilize
the ISA bus driver are registered. A race condition for initilization
exists if device_initcall is used (the isa_bus_init callback is placed
in the same initcall level as dependent drivers which use module_init).
This patch ensures that isa_bus_init is called first by utilizing
postcore_initcall in favor of device_initcall.
Fixes: a5117ba7da ("[PATCH] Driver model: add ISA bus")
Cc: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Several modern devices, such as PC/104 cards, are expected to run on
modern systems via an ISA bus interface. Since ISA is a legacy interface
for most modern architectures, ISA support should remain disabled in
general. Support for ISA-style drivers should be enabled on a per driver
basis.
To allow ISA-style drivers on modern systems, this patch introduces the
ISA_BUS_API and ISA_BUS Kconfig options. The ISA bus driver will now
build conditionally on the ISA_BUS_API Kconfig option, which defaults to
the legacy ISA Kconfig option. The ISA_BUS Kconfig option allows the
ISA_BUS_API Kconfig option to be selected on architectures which do not
enable ISA (e.g. X86_64).
The ISA_BUS Kconfig option is currently only implemented for X86
architectures. Other architectures may have their own ISA_BUS Kconfig
options added as required.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_pm_opp_get_sharing_cpus() returns 0 even in the case when the OPP
core doesn't know whether or not the table is shared. It works on the
majority of platforms, where the OPP table is never created before
invoking the function and then -ENODEV is returned by it.
But in the case of one platform (Jetson TK1) at least, the situation
is a bit different. The OPP table has been created (somehow) before
dev_pm_opp_get_sharing_cpus() is called and it returns 0. Its caller
treats that as 'the CPUs don't share OPPs' and that leads to degraded
performance.
Fix this by converting 'shared_opp' in struct opp_table to an enum
and making dev_pm_opp_get_sharing_cpus() return -EINVAL in case when
the value of that field is "access unknown", so that the caller can
handle it accordingly (cpufreq-dt considers that as 'all CPUs share
the table', for example).
Fixes: 6f707daa38 "PM / OPP: Add dev_pm_opp_get_sharing_cpus()"
Reported-and-tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
[ rjw : Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Not all subsystems/drivers that manages devices attached to a genpd
makes use of the pm_runtime_force_suspend|resume() helper functions
to deal with system PM suspend/resume.
In cases like these and when genpd's ->stop|start() callbacks are
used for the device, invoke the pm_runtime_force_suspend|resume()
helper functions from genpd's "noirq" system PM callbacks. In this
way we make sure to "stop" the device on suspend and to "start" it
on resume.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
In cases when a PM domain isn't powered off when genpd's ->prepare()
callback is invoked, genpd runtime resumes and disables runtime PM for the
device. This behaviour was needed when genpd managed intermediate states
during the power off sequence, as to maintain proper low power states of
devices during system PM suspend/resume.
Commit ba2bbfbf63 (PM / Domains: Remove intermediate states from the
power off sequence), enables genpd to improve its behaviour in that
respect.
The PM core disables runtime PM at __device_suspend_late() before it calls
a system PM "late" callback for a device. When resuming a device, after a
corresponding "early" callback has been invoked, the PM core re-enables
runtime PM.
By changing genpd to allow runtime PM according to the same system PM
phases as the PM core, devices can be runtime resumed by their
corresponding subsystem/driver when really needed.
In this way, genpd no longer need to runtime resume the device from its
->prepare() callback. In most cases that avoids unnecessary and energy-
wasting operations of runtime resuming devices that have nothing to do,
only to runtime suspend them shortly after.
Although, because of changing this behaviour in genpd and due to that
genpd powers on the PM domain unconditionally in the system PM resume
"noirq" phase, it could potentially cause a PM domain to stay powered
on even if it's unused after the system has resumed. To avoid this,
schedule a power off work when genpd's system PM ->complete() callback
has been invoked for the last device in the PM domain.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If the runtime PM status of the device isn't RPM_SUSPENDED, prevent the
pm_runtime_force_resume() from invoking the ->runtime_resume() callback
for the device, as it's not the expected behaviour from the subsystem/driver.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PM core increases the runtime PM usage count at the system PM prepare
phase. Later when the system resumes, it does a pm_runtime_put() in the
complete phase, which in addition to decrementing the usage count, does
the equivalent of a pm_request_idle().
Therefore the call to pm_request_idle() from within genpd's ->complete()
callback is redundant, so remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Due to the previous changes in genpd, which removed the suspend_power_off
flag, several of the system PM callbacks no longer do any additional
checks but only invoke corresponding pm_generic_* helper functions.
To clean up the code, drop these wrapper functions as they have
become redundant. Instead, assign the system PM callbacks directly
to the pm_generic_*() helper functions.
While changing this, it has bocame clear that some of the current
system PM callbacks in genpd invoke wrong driver callbacks. For
example, the genpd's ->restore() callback invokes pm_generic_resume(),
while that should be pm_generic_restore(). Fix that as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
If a PM domain is powered off when the first device starts its system PM
prepare phase, genpd prevents any further attempts to power on the PM
domain during the following system PM phases. Not until the system PM
complete phase is finalized for all devices in the PM domain, genpd again
allows it to be powered on.
This behaviour needs to be changed, as a subsystem/driver for a device in
the same PM domain may still need to be able to serve requests in some of
the system PM phases. Accordingly, it may need to runtime resume its
device and thus also request the corresponding PM domain to be powered on.
To deal with these scenarios, let's make the device operational in the
system PM prepare phase by runtime resuming it, no matter if the PM domain
is powered on or off. Changing this also enables us to remove genpd's
suspend_power_off flag, as it's being used to track this condition.
Additionally, we must allow the PM domain to be powered on via runtime PM
during the system PM phases.
This change also requires a fix in the AMD ACP (Audio CoProcessor) drm
driver. It registers a genpd to model the ACP as a PM domain, but
unfortunately it's also abuses genpd's "internal" suspend_power_off flag
to deal with a corner case at system PM resume.
More precisely, the so called SMU block powers on the ACP at system PM
resume, unconditionally if it's being used or not. This may lead to that
genpd's internal status of the power state, may not correctly reflect the
power state of the HW after a system PM resume.
Because of changing the behaviour of genpd, by runtime resuming devices in
the prepare phase, the AMD ACP drm driver no longer have to deal with this
corner case. So let's just drop the related code in this driver.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Acked-by: Maruthi Bayyavarapu <maruthi.bayyavarapu@amd.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modules which register drivers via standard path (driver_register) in
parallel can cause a warning:
WARNING: CPU: 2 PID: 3492 at ../fs/sysfs/dir.c:31 sysfs_warn_dup+0x62/0x80
sysfs: cannot create duplicate filename '/module/saa7146/drivers'
Modules linked in: hexium_gemini(+) mxb(+) ...
...
Call Trace:
...
[<ffffffff812e63a2>] sysfs_warn_dup+0x62/0x80
[<ffffffff812e6487>] sysfs_create_dir_ns+0x77/0x90
[<ffffffff8140f2c4>] kobject_add_internal+0xb4/0x340
[<ffffffff8140f5b8>] kobject_add+0x68/0xb0
[<ffffffff8140f631>] kobject_create_and_add+0x31/0x70
[<ffffffff8157a703>] module_add_driver+0xc3/0xd0
[<ffffffff8155e5d4>] bus_add_driver+0x154/0x280
[<ffffffff815604c0>] driver_register+0x60/0xe0
[<ffffffff8145bed0>] __pci_register_driver+0x60/0x70
[<ffffffffa0273e14>] saa7146_register_extension+0x64/0x90 [saa7146]
[<ffffffffa0033011>] hexium_init_module+0x11/0x1000 [hexium_gemini]
...
As can be (mostly) seen, driver_register causes this call sequence:
-> bus_add_driver
-> module_add_driver
-> module_create_drivers_dir
The last one creates "drivers" directory in /sys/module/<...>. When
this is done in parallel, the directory is attempted to be created
twice at the same time.
This can be easily reproduced by loading mxb and hexium_gemini in
parallel:
while :; do
modprobe mxb &
modprobe hexium_gemini
wait
rmmod mxb hexium_gemini saa7146_vv saa7146
done
saa7146 calls pci_register_driver for both mxb and hexium_gemini,
which means /sys/module/saa7146/drivers is to be created for both of
them.
Fix this by a new mutex in module_create_drivers_dir which makes the
test-and-create "drivers" dir atomic.
I inverted the condition and removed 'return' to avoid multiple
unlocks or a goto.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Fixes: fe480a2675 (Modules: only add drivers/ direcory if needed)
Cc: v2.6.21+ <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While trying to convert a DMA driver from bool to tristate, we
encountered the following:
ERROR: "pm_clk_add_clk" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_create" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_destroy" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_suspend" [drivers/dma/tegra210-adma.ko] undefined!
ERROR: "pm_clk_resume" [drivers/dma/tegra210-adma.ko] undefined!
Since in principle there is nothing preventing these functions
from being used in modular code as well as builtin, we add the
export of them. We expand the scope to also include:
pm_clk_add
of_pm_clk_add_clks
pm_clk_remove
pm_clk_remove_clk
pm_clk_init
pm_clk_runtime_suspend
pm_clk_runtime_resume
pm_clk_add_notifier
...since these functions are also non-static and presumably form
part of the existing API used by other drivers that may become
modular in the future.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The s390 cpu topology gained another hierarchy level. The top level is
now called drawer and contains several books. A book used to be the
top level.
In order to expose the cpu topology to user space allow to create new
sysfs attributes dependent on CONFIG_SCHED_DRAWER which an
architecture may define and select.
These additional attributes will be available:
/sys/devices/system/cpu/cpuX/topology/drawer_id
/sys/devices/system/cpu/cpuX/topology/drawer_siblings
/sys/devices/system/cpu/cpuX/topology/drawer_siblings_list
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit 3195ef59cb ("x86: Do full rtc synchronization with ntp") had
the side-effect of unconditionally enabling the RTC_LIB symbol on x86,
which in turn disables the selection of the CONFIG_RTC and
CONFIG_GEN_RTC drivers that contain a two older implementations of
the CONFIG_RTC_DRV_CMOS driver.
This removes x86 from the list for genrtc, and changes all references
to the asm/rtc.h header to instead point to the interfaces
from linux/mc146818rtc.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Regmap irq implements the generic interrupt service routine which
is common for most of devices. Some devices, like MAX77620, MAX20024
needs the special handling before and after servicing the interrupt
as generic. For the example, MAX77620 programming guidelines for
interrupt servicing says:
1. When interrupt occurs from PMIC, mask the PMIC interrupt by setting
GLBLM.
2. Read IRQTOP and service the interrupt accordingly.
3. Once all interrupts has been checked and serviced, the interrupt
service routine un-masks the hardware interrupt line by clearing
GLBLM.
The step (2) is implemented in regmap irq as generic routine. For
step (1) and (3), add callbacks from regmap irq to client driver
to handle chip specific configurations.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
- Stable-candidate cpuidle fix to make it check the right variable
when deciding whether or not to enable interrupts on the local CPU
so as to avoid enabling iterrupts too early in some cases if the
system has both coupled and per-core idle states (Daniel Lezcano).
- Stable-candidate PM core fix to make it handle failures at the
"late suspend" stage of device suspend consistently for all
devices regardless of whether or not async suspend/resume is
enabled for them (Rafael Wysocki).
- Cleanups in the cpufreq core, the schedutil governor and the
intel_pstate driver (Rafael Wysocki, Pankaj Gupta, Viresh Kumar).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=3vtL
-----END PGP SIGNATURE-----
Merge tag 'pm-4.7-rc1-more' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power management updates from Rafael Wysocki:
"These are two stable-candidate fixes (PM core, cpuidle) and a bunch of
cpufreq cleanups.
Specifics:
- Stable-candidate cpuidle fix to make it check the right variable
when deciding whether or not to enable interrupts on the local CPU
so as to avoid enabling iterrupts too early in some cases if the
system has both coupled and per-core idle states (Daniel Lezcano).
- Stable-candidate PM core fix to make it handle failures at the
"late suspend" stage of device suspend consistently for all devices
regardless of whether or not async suspend/resume is enabled for
them (Rafael Wysocki).
- Cleanups in the cpufreq core, the schedutil governor and the
intel_pstate driver (Rafael Wysocki, Pankaj Gupta, Viresh Kumar)"
* tag 'pm-4.7-rc1-more' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / sleep: Handle failures in device_suspend_late() consistently
cpufreq: schedutil: Improve prints messages with pr_fmt
cpuidle: Fix cpuidle_state_is_coupled() argument in cpuidle_enter()
cpufreq: simplified goto out in cpufreq_register_driver()
cpufreq: governor: CPUFREQ_GOV_STOP never fails
cpufreq: governor: CPUFREQ_GOV_POLICY_EXIT never fails
intel_pstate: Simplify conditional in intel_pstate_set_policy()
Here's the "big" driver core update for 4.7-rc1.
Mostly just debugfs changes, the long-known and messy races with removing
debugfs files should be fixed thanks to the great work of Nicolai Stange. We
also have some isa updates in here (the x86 maintainers told me to take it
through this tree), a new warning when we run out of dynamic char major
numbers, and a few other assorted changes, details in the shortlog.
All have been in linux-next for some time with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlc/0mwACgkQMUfUDdst+ynjXACgjNxR5nMUiM8ZuuD0i4Xj7VXd
hnIAoM08+XDCv41noGdAcKv+2WZVZWMC
=i+0H
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here's the "big" driver core update for 4.7-rc1.
Mostly just debugfs changes, the long-known and messy races with
removing debugfs files should be fixed thanks to the great work of
Nicolai Stange. We also have some isa updates in here (the x86
maintainers told me to take it through this tree), a new warning when
we run out of dynamic char major numbers, and a few other assorted
changes, details in the shortlog.
All have been in linux-next for some time with no reported issues"
* tag 'driver-core-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (32 commits)
Revert "base: dd: don't remove driver_data in -EPROBE_DEFER case"
gpio: ws16c48: Utilize the ISA bus driver
gpio: 104-idio-16: Utilize the ISA bus driver
gpio: 104-idi-48: Utilize the ISA bus driver
gpio: 104-dio-48e: Utilize the ISA bus driver
watchdog: ebc-c384_wdt: Utilize the ISA bus driver
iio: stx104: Utilize the module_isa_driver and max_num_isa_dev macros
iio: stx104: Add X86 dependency to STX104 Kconfig option
Documentation: Add ISA bus driver documentation
isa: Implement the max_num_isa_dev macro
isa: Implement the module_isa_driver macro
pnp: pnpbios: Add explicit X86_32 dependency to PNPBIOS
isa: Decouple X86_32 dependency from the ISA Kconfig option
driver-core: use 'dev' argument in dev_dbg_ratelimited stub
base: dd: don't remove driver_data in -EPROBE_DEFER case
kernfs: Move faulting copy_user operations outside of the mutex
devcoredump: add scatterlist support
debugfs: unproxify files created through debugfs_create_u32_array()
debugfs: unproxify files created through debugfs_create_blob()
debugfs: unproxify files created through debugfs_create_bool()
...
Grygorii Strashko reports:
The PM runtime will be left disabled for the device if its
.suspend_late() callback fails and async suspend is not allowed
for this device. In this case device will not be added in
dpm_late_early_list and dpm_resume_early() will ignore this
device, as result PM runtime will be disabled for it forever
(side effect: after 8 subsequent failures for the same device
the PM runtime will be reenabled due to disable_depth overflow).
To fix this problem, add devices to dpm_late_early_list regardless
of whether or not device_suspend_late() returns errors for them.
That will ensure failures in there to be handled consistently for
all devices regardless of their async suspend/resume status.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: All applicable <stable@vger.kernel.org>
Just one commit reworking the handling of built-in properties
initialization and updating a few drivers in accordance with the
core framework changes.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=O8T9
-----END PGP SIGNATURE-----
Merge tag 'device-properties-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull device properties update from Rafael Wysocki:
"Generic device properties framework update.
Just one commit reworking the handling of built-in properties
initialization and updating a few drivers in accordance with the core
framework changes"
* tag 'device-properties-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: don't bother the drivers with struct property_set
- New cpufreq "schedutil" governor (making decisions based on CPU
utilization information provided by the scheduler and capable of
switching CPU frequencies right away if the underlying driver
supports that) and support for fast frequency switching in the
acpi-cpufreq driver (Rafael Wysocki).
- Consolidation of CPU frequency management on ARM platforms allowing
them to get rid of some platform-specific boilerplate code if they
are going to use the cpufreq-dt driver (Viresh Kumar, Finley Xiao,
Marc Gonzalez).
- Support for ACPI _PPC and CPU frequency limits in the intel_pstate
driver (Srinivas Pandruvada).
- Fixes and cleanups in the cpufreq core and generic governor code
(Rafael Wysocki, Sai Gurrappadi).
- intel_pstate driver optimizations and cleanups (Rafael Wysocki,
Philippe Longepe, Chen Yu, Joe Perches).
- cpufreq powernv driver fixes and cleanups (Akshay Adiga, Shilpasri
Bhat).
- cpufreq qoriq driver fixes and cleanups (Jia Hongtao).
- ACPI cpufreq driver cleanups (Viresh Kumar).
- Assorted cpufreq driver updates (Ashwin Chaugule, Geliang Tang,
Javier Martinez Canillas, Paul Gortmaker, Sudeep Holla).
- Assorted cpufreq fixes and cleanups (Joe Perches, Arnd Bergmann).
- Fixes and cleanups in the OPP (Operating Performance Points)
framework, mostly related to OPP sharing, and reorganization of
OF-dependent code in it (Viresh Kumar, Arnd Bergmann, Sudeep Holla).
- New "passive" governor for devfreq (for SoC subsystems that will
rely on someone else for the management of their power resources)
and consolidation of devfreq support for Exynos platforms, coding
style and typo fixes for devfreq (Chanwoo Choi, MyungJoo Ham).
- PM core fixes and cleanups, mostly to make it work better with the
generic power domains (genpd) framework, and updates for that
framework (Ulf Hansson, Thierry Reding, Colin Ian King).
- Intel Broxton support for the intel_idle driver (Len Brown).
- cpuidle core optimization and fix (Daniel Lezcano, Dave Gerlach).
- ARM cpuidle cleanups (Jisheng Zhang).
- Intel Kabylake support for the RAPL power capping driver (Jacob Pan).
- AVS (Adaptive Voltage Switching) rockchip-io driver update (Heiko
Stuebner).
- Updates for the cpupower tool (Arjun Sreedharan, Colin Ian King,
Mattia Dongili, Thomas Renninger).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQIcBAABCAAGBQJXOjLgAAoJEILEb/54YlRxfn0P/RbSPpNlUNBIE8DFrdD9jRdJ
TIpZ7uiHi9tU1ZF17UBbb/SwuWfYVnVmiorZGRfFOtGaoqh0HFZ/nplDz99rK0ku
vW2OnbojMQEUMU3IcUT1y4BsSl0H23f7ZOKrdprALeWxDQmbgnYjrE6vkX6hRtld
A8eeZvIEJ5CzV8S+9aOOOpojW2yXk5dYGdZ7gpQdoM0n7zVLyPnNucJoha3BYmOG
FwKEIe05RpIhfLfGT0CXIRcOzwAZ6ZWKgOrXUrx/AadPbvu/TP9zkI0djYI8ukyv
z2oiO/GExoeGVuUzvy8vY5SiH4NQvViftFzMZepcsmjxmVglohMPRL8VLjZIBckk
DDcqH9e0OQI20jjYT1vIf5+JWBvLxuQfGtyzI0S+sE/elB1zI/3O8p+8N2CuF5n+
my2dawIewnHI/0AdSpJ+K7DVrfwPHAX19axtPX3dJSLh2OuHCPNlAtbxRGAriBfH
Zv9NETxlrch69o2AD4K54DErWV1FsYLznzK5Zms6MC2Ispbb+oiYpacTlZblznvb
H5U2SSNlA5Niir3vVJ01nKRtzxlWoi67CQxbYrGhlaR0nTTxf9HqWgcSiTZrn7Pv
hs+LA2aUfMf3JGjStdORS7S8biQSid5vypfkglpWLZBKHNC9BqqZd9gSM+jF3FVh
ps4mMM4UXY4hnoFDkMBI
=WM89
-----END PGP SIGNATURE-----
Merge tag 'pm-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"The majority of changes go into the cpufreq subsystem this time.
To me, quite obviously, the biggest ticket item is the new "schedutil"
governor. Interestingly enough, it's the first new cpufreq governor
since the beginning of the git era (except for some out-of-the-tree
ones).
There are two main differences between it and the existing governors.
First, it uses the information provided by the scheduler directly for
making its decisions, so it doesn't have to track anything by itself.
Second, it can invoke drivers (supporting that feature) to adjust CPU
performance right away without having to spawn work items to be
executed in process context or similar. Currently, the acpi-cpufreq
driver is the only one supporting that mode of operation, but then it
is used on a large number of systems.
The "schedutil" governor as included here is very simple and mostly
regarded as a foundation for future work on the integration of the
scheduler with CPU power management (in fact, there is work in
progress on top of it already). Nevertheless it works and the
preliminary results obtained with it are encouraging.
There also is some consolidation of CPU frequency management for ARM
platforms that can add their machine IDs the the new stub dt-platdev
driver now and that will take care of creating the requisite platform
device for cpufreq-dt, so it is not necessary to do that in platform
code any more. Several ARM platforms are switched over to using this
generic mechanism.
In addition to that, the intel_pstate driver is now going to respect
CPU frequency limits set by the platform firmware (or a BMC) and
provided via the ACPI _PPC object.
The devfreq subsystem is getting a new "passive" governor for SoCs
subsystems that will depend on somebody else to manage their voltage
rails and its support for Samsung Exynos SoCs is consolidated.
The rest is support for new hardware (Intel Broxton support in
intel_idle for one example), bug fixes, optimizations and cleanups in
a number of places.
Specifics:
- New cpufreq "schedutil" governor (making decisions based on CPU
utilization information provided by the scheduler and capable of
switching CPU frequencies right away if the underlying driver
supports that) and support for fast frequency switching in the
acpi-cpufreq driver (Rafael Wysocki)
- Consolidation of CPU frequency management on ARM platforms allowing
them to get rid of some platform-specific boilerplate code if they
are going to use the cpufreq-dt driver (Viresh Kumar, Finley Xiao,
Marc Gonzalez)
- Support for ACPI _PPC and CPU frequency limits in the intel_pstate
driver (Srinivas Pandruvada)
- Fixes and cleanups in the cpufreq core and generic governor code
(Rafael Wysocki, Sai Gurrappadi)
- intel_pstate driver optimizations and cleanups (Rafael Wysocki,
Philippe Longepe, Chen Yu, Joe Perches)
- cpufreq powernv driver fixes and cleanups (Akshay Adiga, Shilpasri
Bhat)
- cpufreq qoriq driver fixes and cleanups (Jia Hongtao)
- ACPI cpufreq driver cleanups (Viresh Kumar)
- Assorted cpufreq driver updates (Ashwin Chaugule, Geliang Tang,
Javier Martinez Canillas, Paul Gortmaker, Sudeep Holla)
- Assorted cpufreq fixes and cleanups (Joe Perches, Arnd Bergmann)
- Fixes and cleanups in the OPP (Operating Performance Points)
framework, mostly related to OPP sharing, and reorganization of
OF-dependent code in it (Viresh Kumar, Arnd Bergmann, Sudeep Holla)
- New "passive" governor for devfreq (for SoC subsystems that will
rely on someone else for the management of their power resources)
and consolidation of devfreq support for Exynos platforms, coding
style and typo fixes for devfreq (Chanwoo Choi, MyungJoo Ham)
- PM core fixes and cleanups, mostly to make it work better with the
generic power domains (genpd) framework, and updates for that
framework (Ulf Hansson, Thierry Reding, Colin Ian King)
- Intel Broxton support for the intel_idle driver (Len Brown)
- cpuidle core optimization and fix (Daniel Lezcano, Dave Gerlach)
- ARM cpuidle cleanups (Jisheng Zhang)
- Intel Kabylake support for the RAPL power capping driver (Jacob
Pan)
- AVS (Adaptive Voltage Switching) rockchip-io driver update (Heiko
Stuebner)
- Updates for the cpupower tool (Arjun Sreedharan, Colin Ian King,
Mattia Dongili, Thomas Renninger)"
* tag 'pm-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (112 commits)
intel_pstate: Clean up get_target_pstate_use_performance()
intel_pstate: Use sample.core_avg_perf in get_avg_pstate()
intel_pstate: Clarify average performance computation
intel_pstate: Avoid unnecessary synchronize_sched() during initialization
cpufreq: schedutil: Make default depend on CONFIG_SMP
cpufreq: powernv: del_timer_sync when global and local pstate are equal
cpufreq: powernv: Move smp_call_function_any() out of irq safe block
intel_pstate: Clean up intel_pstate_get()
cpufreq: schedutil: Make it depend on CONFIG_SMP
cpufreq: governor: Fix handling of special cases in dbs_update()
PM / OPP: Move CONFIG_OF dependent code in a separate file
cpufreq: intel_pstate: Ignore _PPC processing under HWP
cpufreq: arm_big_little: use generic OPP functions for {init, free}_opp_table
PM / OPP: add non-OF versions of dev_pm_opp_{cpumask_, }remove_table
cpufreq: tango: Use generic platdev driver
PM / OPP: pass cpumask by reference
cpufreq: Fix GOV_LIMITS handling for the userspace governor
cpupower: fix potential memory leak
PM / devfreq: style/typo fixes
PM / devfreq: exynos: Add the detailed correlation for Exynos5422 bus
..
* pm-opp:
PM / OPP: Move CONFIG_OF dependent code in a separate file
PM / OPP: add non-OF versions of dev_pm_opp_{cpumask_, }remove_table
PM / OPP: pass cpumask by reference
PM / OPP: Add dev_pm_opp_get_sharing_cpus()
PM / OPP: Mark cpumask as const in dev_pm_opp_set_sharing_cpus()
PM / OPP: -ENOSYS is applicable only to syscalls
PM / OPP: Mark shared-opp for non-dt case
PM / OPP: Relocate dev_pm_opp_set_sharing_cpus()
PM / OPP: dev_pm_opp_set_sharing_cpus() doesn't depend on CONFIG_OF
PM / OPP: Add missing doc style comments
PM / OPP: Propagate the error returned by _find_opp_table()
Recently, a few issues were noticed in the code where CONFIG_OF wasn't
consistently used for many routines. The core file is big enough now and
ifdef hackery makes it less readable.
Move OF-specific code to another file and compile that only if CONFIG_OF
is enabled.
Compile-tested:
- For ARM (exynos) with CONFIG_OF enabled
- For X86 with CONFIG_OF disabled (have to enable CONFIG_PM_OPP separately)
No functional changes.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
* pm-opp-fixes:
PM / OPP: Remove useless check
* pm-cpufreq-fixes:
intel_pstate: Fix intel_pstate_get()
cpufreq: intel_pstate: Fix HWP on boot CPU after system resume
cpufreq: st: enable selective initialization based on the platform
* pm-cpuidle-fixes:
ARM: cpuidle: Pass on arm_cpuidle_suspend()'s return value
Regulators are optional for devices using OPPs and the OPP core
shouldn't be printing any errors for such missing regulators.
It was fine before the commit 0c717d0f9c, but that failed to update
this part of the code to remove an 'always true' check and an extra
unwanted print message.
Fix that now.
Fixes: 0c717d0f9c (PM / OPP: Initialize regulator pointer to an error value)
Reported-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Functions dev_pm_opp_of_{cpumask_,}remove_table removes/frees all the
static OPP entries associated with the device and/or all cpus(in case
of cpumask) that are created from DT.
However the OPP entries are populated reading from the firmware or some
different method using dev_pm_opp_add are marked dynamic and can't be
removed using above functions.
This patch adds non DT/OF versions of dev_pm_opp_{cpumask_,}remove_table
to support the above mentioned usecase.
This is in preparation to make use of the same in scpi-cpufreq.c
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The new use of dev_pm_opp_set_sharing_cpus resulted in a harmless compiler
warning with CONFIG_CPUMASK_OFFSTACK=y:
drivers/cpufreq/mvebu-cpufreq.c: In function 'armada_xp_pmsu_cpufreq_init':
include/linux/cpumask.h:550:25: error: passing argument 2 of 'dev_pm_opp_set_sharing_cpus' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
The problem here is that cpumask_var_t gets passed by reference, but
by declaring a 'const cpumask_var_t' argument, only the pointer is
constant, not the actual mask. This is harmless because the function
does not actually modify the mask.
This patch changes the function prototypes for all of the related functions
to pass a 'struct cpumask *' instead of 'cpumask_var_t', matching what
most other such functions do in the kernel. This lets us mark all the
other similar functions as taking a 'const' mask where possible,
and it avoids the warning without any change in object code.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 947bd567f7 (mvebu: Use dev_pm_opp_set_sharing_cpus() to mark OPP tables as shared)
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit ded9db380d.
Thierry Reding writes:
This causes a boot regression on at least one board, caused by
one of the drivers looking at driver data to check whether or
not the driver has properly loaded. If the code encounters a
non-NULL pointer it tries to dereference it, but because it's
already been freed there is no memory backing it and things
crash.
I don't think keeping stale pointers around is a good idea. The
whole point of setting this to NULL in the core is so that probe
failures result in the same starting conditions no matter what.
Can we please get this reverted?
Reported-by: Thierry Reding <thierry.reding@gmail.com>
Cc: Yi Zhang <yizhang_hust@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The introduction of the ISA_BUS option blocks the compilation of ISA
drivers on non-x86 platforms. The ISA_BUS configuration option should
not be necessary if the X86_32 dependency can be decoupled from the ISA
configuration option. This patch both removes the ISA_BUS configuration
option entirely and removes the X86_32 dependency from the ISA
configuration option.
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
the driver_data may be used for sanity check, it fails the
probe() if driver_data is NULL after it is re-triggered.
for example, soc_probe() in sound/soc/soc-core.c
Signed-off-by: Yi Zhang <yizhang_hust@163.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OPP core allows a platform to mark OPP table as shared, when the
platform isn't using operating-points-v2 bindings.
And, so there should be a non DT way of finding out if the OPP table is
shared or not.
This patch adds dev_pm_opp_get_sharing_cpus(), which first tries to get
OPP sharing information from the opp-table (in case it is already marked
as shared), otherwise it uses the existing DT way of finding sharing
information.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
dev_pm_opp_set_sharing_cpus() isn't supposed to update the cpumask
passed as its parameter, and so it should always have been marked
'const'.
Do it now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit 32e8d689dc (PM / sleep: trace_device_pm_callback coverage in
dpm_prepare/complete) removed all users of this variable but forgot to
remove the variable itself.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[ rjw: Subject ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Since fwnode may hold ERR_PTR(-ENODEV) or it may be NULL,
the fwnode type checks is_of_node(), is_acpi_node() and is
is_pset_node() need to consider it. Using IS_ERR_OR_NULL()
to check it.
Fixes: 0d67e0fa16 (device property: fix for a case of use-after-free)
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
[ rjw: Subject & changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As the PM core already have wakeup management during the system PM phase,
it seems reasonable that genpd and its users should be able to rely on
that. Therefore let's remove this from pm_genpd_prepare().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The PM core increases and decreases the runtime PM usage count in the
system PM prepare phase. This makes some of the pm_runtime_get|put*()
calls in pm_genpd_prepare() redundant, so let's remove them.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
It is entirely possible for of_count_phandle_wit_args to
return a -ve error return value so we need to check for this
otherwise we end up allocating a negative number of clk objects.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
opp core allows OPPs to be explicitly marked as shared from platform
code, in case of operating-point v1 bindings.
Though we do everything fine in that case, we don't set the flag in the
opp-table to indicate that the OPPs are shared. It works fine today as
the flag isn't used anywhere else in the core, but we should be doing
the right thing by marking it set.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Move dev_pm_opp_set_sharing_cpus() towards the end of the file. This
is required for better readability after the next patch is applied,
which adds dev_pm_opp_get_sharing_cpus().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Few of the routines in cpu.c were missing these, add them.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Don't send -EINVAL and propagate what's received from _find_opp_table().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As a part of the ongoing consolidation of genpd, it's become questionable
whether clients actually needs to be able to assign their own set of
->save|restore_state() callbacks. Currently all users copes fine with the
default callbacks, so let's remove the configuration option and stick to
the default ones.
This enables further clarifications of the related code and let's also
rename pm_genpd_default_save|restore_state() into
__genpd_runtime_suspend|resume() to apply the rule of static functionnames
in genpd.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Follow genpd's rule for names of static functions, by renaming
pm_genpd_runtime_suspend|resume() to genpd_runtime_suspend|resume().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The genpd governor validates the latency constraints to find out whether
it's acceptable to runtime suspend a device. Earlier this validation was
made to know whether it was okay to invoke the ->stop() callback for the
device, hence the governor used the name "stop_ok" for the related
variables.
To clarify the code around this, let's rename these variables from
"stop_ok" to "suspend_ok".
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As pm_runtime_set_active() may fail because the device's parent isn't
active, we can end up executing the ->runtime_resume() callback for the
device when it isn't allowed.
Fix this by invoking pm_runtime_set_active() before running the callback
and let's also deal with the error code.
Fixes: 37f204164d (PM: Add pm_runtime_suspend|resume_force functions)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: 3.15+ <stable@vger.kernel.org> # 3.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add scatterlist support (dev_coredumpsg) to allow drivers to avoid
vmalloc() like dev_coredumpm(), while also avoiding the module
reference that the latter function requires.
This internally uses dev_coredumpm() with function inside the
devcoredump module, requiring removing the const
(which touches the driver using it.)
Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Specifically for the case of reads that use the Extended Register
Read Long command, a multi-byte read operation is broken up into
8-byte chunks. However the call to spmi_ext_register_readl() is
incorrectly passing 'val_size', which if greater than 8 will
always fail. The argument should instead be 'len'.
Fixes: c9afbb05a9 ("regmap: spmi: support base and extended register spaces")
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Since device_add_property_set() now always takes a copy of
the property_set, and also since the fwnode type is always
hard coded to be FWNODE_PDATA, there is no need for the
drivers to deliver the entire struct property_set. The
function can just create the instance of it on its own and
bind the properties from the drivers to it on the spot.
This renames device_add_property_set() to
device_add_properties(). The function now takes struct
property_entry as its parameter instead of struct
property_set.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Linus Torvalds