Since the ARM AMBA bus is used on MIPS as well as ARM, we need
to make the bus available for other architectures to use. Move
the AMBA include files from include/asm-arm/hardware/ to
include/linux/amba/
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Before this patch we were just using the "classic" /dev/ttySx devices.
However when another on the system is loaded that uses those (like drivers for
serial PCMCIA), that creates a conflict for the minors. Therefore, we now use
/dev/ttyPSC[0:5] (note the 0-based numbering !) with some minors we've been
assigned in the "Low Density Serial port major"
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Unify the EVENT_CARD_INSERTION and "attach" callbacks to one unified
probe() callback. As all in-kernel drivers are changed to this new
callback, there will be no temporary backwards-compatibility. Inside a
probe() function, each driver _must_ set struct pcmcia_device
*p_dev->instance and instance->handle correctly.
With these patches, the basic driver interface for 16-bit PCMCIA drivers
now has the classic four callbacks known also from other buses:
int (*probe) (struct pcmcia_device *dev);
void (*remove) (struct pcmcia_device *dev);
int (*suspend) (struct pcmcia_device *dev);
int (*resume) (struct pcmcia_device *dev);
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The linked list of devices managed by each PCMCIA driver is, in very most
cases, unused. Therefore, remove it from many drivers.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Unify the "detach" and REMOVAL_EVENT handlers to one "remove" function.
Old functionality is preserved, for the moment.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Move the suspend and resume methods out of the event handler, and into
special functions. Also use these functions for pre- and post-reset, as
almost all drivers already do, and the remaining ones can easily be
converted.
Bugfix to include/pcmcia/ds.c
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
All call sites for serial8250_handle_port() acquired the port spinlock
and released it afterwards. This is a needless duplication of code.
Move the spinlocking inside serial8250_handle_port().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The function uart_match_port() incorrectly compares the ioremap'd
virtual addresses of ports instead of the physical address to find
duplicate ports for MMIO based UARTs. This fixes it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I've also fixed the sort-ordering comments on this naming convention.
Signed-off-by: Stuart MacDonald <stuartm@connecttech.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Reading the MSR register on 8250-compatible UARTs results in any
modem status interrupts being cleared. To avoid missing any
status changes, arrange for get_mctrl() to read the current
status via check_modem_status(), which will process any pending
state changes for us.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems that clk_use() and clk_unuse() are additional complexity
which isn't required anymore. Remove them from the clock framework
to avoid the additional confusion which they cause, and update all
ARM machine types except for OMAP.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Erik Hovland
This patch provides two changes. An indent is supplied for an if/else clause so that it is more readable. An acronym is incorrectly typed as UER when it should be IER.
Signed-off-by: Erik Hovland <erik@hovland.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce a Kconfig symbol SPARC that is defined on both the sparc and
sparc64 architectures.
This symbol makes some dependencies more readable.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completed a major overhaul of the Resource Manager code -
specifically, optimizations in the area of the AML/internal
resource conversion code. The code has been optimized to
simplify and eliminate duplicated code, CPU stack use has
been decreased by optimizing function parameters and local
variables, and naming conventions across the manager have
been standardized for clarity and ease of maintenance (this
includes function, parameter, variable, and struct/typedef
names.)
All Resource Manager dispatch and information tables have
been moved to a single location for clarity and ease of
maintenance. One new file was created, named "rsinfo.c".
The ACPI return macros (return_ACPI_STATUS, etc.) have
been modified to guarantee that the argument is
not evaluated twice, making them less prone to macro
side-effects. However, since there exists the possibility
of additional stack use if a particular compiler cannot
optimize them (such as in the debug generation case),
the original macros are optionally available. Note that
some invocations of the return_VALUE macro may now cause
size mismatch warnings; the return_UINT8 and return_UINT32
macros are provided to eliminate these. (From Randy Dunlap)
Implemented a new mechanism to enable debug tracing for
individual control methods. A new external interface,
acpi_debug_trace(), is provided to enable this mechanism. The
intent is to allow the host OS to easily enable and disable
tracing for problematic control methods. This interface
can be easily exposed to a user or debugger interface if
desired. See the file psxface.c for details.
acpi_ut_callocate() will now return a valid pointer if a
length of zero is specified - a length of one is used
and a warning is issued. This matches the behavior of
acpi_ut_allocate().
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This patch marks a few serial data structures const, moving them to
.rodata where they won't false-share cachelines with things that get
written to.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since the spinlock was removed from sa1100_start_tx(), the "flags"
variable becomes redundant. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The receiver status register reports latched error conditions, which
must be cleared by writing to it. However, the data register reports
unlatched conditions which are associated with the current character.
Use the data register to interpret error status rather than the RSR.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Depend on GSC, not PARISC. Machines without GSC don't have a MUX.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This commit is in response to a bug reported by Vesa on the irc channel
a couple of weeks ago.
The bug was that the console would apparently hang (not return) while
using the mux console.
The root cause of this bug is that bash (with readline support) makes a
call to the tcsetattr() glibc function with the argument TCSADRAIN. This
causes the serial core in the kernel use the uart_wait_until_sent() to be
called. This function verifies the mux transmit queue is empty or calls the
msleep_interruptable() with a calculated timeout value that is dependant
upon the port->timeout variable.
The real problem here is that the port->timeout was not defined so it
was defaulted to 0 and the timeout calculation performs the following
calculation:
char_time = (port->timeout - HZ/50) / port->fifosize;
where char_time is an unsigned long. Since the serial Mux does not use
interrupts, the msleep_interruptable() function waits until the timeout
has been reached ... and when the port->timeout < HZ/50 this timeout will
be a long time. (I have validated that the console will eventually
return ... but it takes quite a while for this to happen).
This patch simply sets the port->timeout on the Mux to HZ/50 to avoid
this long timeout period.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
This patch does the following:
* Fixes compiler warnings.
* Replaces a __raw_readl call with the existing macro.
Signed-off-by: Ryan Bradetich <rbrad@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Changed jobs and the Freescale address is no longer valid.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since few people need the support anymore, this moves the legacy
pm_xxx functions to CONFIG_PM_LEGACY, and include/linux/pm_legacy.h.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we fail to re-startup a serial port on resume, shut it down
immediately and mark it as an error condition.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Claim the WACF005 device. This is the pen display pointing device on
the HP Compaq tc1100 Tablet PC. More information about using this
device, including using it as an X pointer device:
http://www.theory.bham.ac.uk/staff/schofield/linux/tc1100/
Christopher Kemp <ck231@cam.ac.uk> did the legwork of determining that
the WACF005 is really just a plain old UART and doing an initial ACPI
driver (before we had PNPACPI), and David Ludlow <dave@adsllc.com>
confirmed that PNPACPI + the attached patch is now sufficient:
pnp: Device 00:05 activated.
ttyS4 at I/O 0x300 (irq = 4) is a 16550A
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix copy-paste bug in mpc52xx_uart.c (pdev<->dev)
Signed-off-by: Andrey Volkov <avolkov@varma-el.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use physical addresses at the interface level, letting drivers remap
them as appropriate.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
xscale-type UARTs have an extra bit (UUE) in the IER register that has
to be written as 1 to enable the UART. At the end of autoconfig() in
drivers/serial/8250.c, the IER register is unconditionally written as
zero, which turns off the UART, and makes any subsequent printch() hang
the box.
Since other 8250-type UARTs don't have this enable bit and are thus
always 'enabled' in this sense, it can't hurt to enable xscale-type
serial ports all the time as well. The attached patch changes the
autoconfig() exit path to see if the port has an UUE enable bit, and if
yes, to write UUE=1 instead of just putting a zero into IER, using the
same test as is used at the beginning of serial8250_console_write().
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows us to eliminate the casts in the drivers, and eventually
remove the use of the device_driver function pointer methods for
platform device drivers.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the Freescale 5208 processor UART's to the common
ColdFire serial port code.
Patch originally from Matt Waddel (from code originally written by
Mike Lavender).
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use schedule_timeout_uninterruptible() instead of
set_current_state()/schedule_timeout() to reduce kernel size.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Large console spews from IRQ or local_irq_disable() sections can cause the NMI
watchdog to go off.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The offsets of the registers are in a different place, and
some parts cannot handle a full set of modem control signals.
Signed-off-by: Pantelis Antoniou <pantelis@embeddedalley.ocm>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix sparse warning about passing `0` to simple_strtoul()
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Folk seem to get confused when they see two or more ttyS0 ports
appearing at boot time. One comes from the legacy table, and
one from PNP.
Hence, display the bus ID of the device which supplied the port.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Added a Receive_Abort to the Marvell serial driver
Fix occasional input overrun errors on Marvell serial driver
- If the Marvell serial driver is repeatedly started and then stopped it
will occasionally report an input overrun error when started.
- Added a Receive_Abort to the Marvell serial driver to abort previously
received receive errors when re-starting the receive
Acked-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Carlos Sanchez <csanchez@mvista.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Various small mods for the Altix ioc4 serial driver - mostly cleanup:
- remove UIF_INITIALIZED usage
- use the 'lock' from uart_port
- better multiple card support
Signed-off-by: Patrick Gefre <pfg@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes an issue reported by Coverity in serial/serial_core.c
Error reported: Variable "&((info)->tty)->flags" tracked as NULL was passed to a
function that dereferences it.
The later statements in the function assumes 'info->tty != NULL', so this
check is not necessary. Probably a 'BUG_ON(info->tty == NULL)' can be added.
Signed-off-by: Jayachandran C. <c.jayachandran at gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the IMX serial driver to unregister its driver structure
when it is unloaded.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert everyone who uses platform_bus_type to include
linux/platform_device.h.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
In PM v1, all devices were called at SUSPEND_DISABLE level. Then
all devices were called at SUSPEND_SAVE_STATE level, and finally
SUSPEND_POWER_DOWN level. However, with PM v2, to maintain
compatibility for platform devices, I arranged for the PM v2
suspend/resume callbacks to call the old PM v1 suspend/resume
callbacks three times with each level in order so that existing
drivers continued to work.
Since this is obsolete infrastructure which is no longer necessary,
we can remove it. Here's an (untested) patch to do exactly that.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Jon Ringle
Updated 2898/1 per comments:
- Removed fixup
- Moved code in mach-mp1000/ to mach-clps711x/
- Cleaned up code in mp1000-seprom.c. Eliminated code that displayed the contents of the eeprom
Please comment.
Signed-off-by: Jon Ringle
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the new ID 0x132a and configure the new PCI Diva console port. This
device supports only 1 single console UART.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested by Wolfgang Denk with this device:
00:0f.0 Network controller: PLX Technology, Inc. PCI <-> IOBus Bridge (rev 01)
Subsystem: Exsys EX-4055 4S(16C550) RS-232
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=128]
Region 1: I/O ports at 7080 [size=128]
Region 2: I/O ports at 7400 [size=32]
00:0f.0 Class 0280: 10b5:9050 (rev 01)
Subsystem: d84d:4055
Results with this patch:
Serial: 8250/16550 driver $Revision: 1.90 $ 32 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Found IRQ 10 for device 0000:00:0f.0
ttyS4 at I/O 0x7400 (irq = 10) is a 16550A
ttyS5 at I/O 0x7408 (irq = 10) is a 16550A
ttyS6 at I/O 0x7410 (irq = 10) is a 16550A
ttyS7 at I/O 0x7418 (irq = 10) is a 16550A
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Missing spin_lock_init() made the Mux driver hang on SMP systems.
Fix up users of ->hpa to use ->hpa.start instead
Remove warning in 8250_gsc.c by eliminating serial_line_nr
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Convert pa_dev->hpa from an unsigned long to a struct resource.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Fix up users of ->hpa to use ->hpa.start instead.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Make /sys/bus/parisc/drivers look better by cleaning up parisc_driver
names.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
The modem is said to work with belows addition to pnp_dev_table[]:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=296011
Signed-off-by: maximilian attems <janitor@sternwelten.at>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Argument does not agree.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Lothar Wassmann
The function serial_pxa_set_termios() is calling uart_update_timeout()
with the baud rate divisor as third parameter, while
uart_update_timeout() expects the baud rate in this place.
This results in a bogus port->timeout which is proportional to the
baud rate.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The s3c2410 serial driver is missing static declerations
on several functions that are not exported, and have no
need of being exported outside the driver
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Incorrect uart_write_wakeup() calls cause reference to a
NULL tty pointer in sunsab and sunzilog serial drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Ben Dooks
Initialise the driver's .owner field so that
the device driver can be referenced to the
module that owns it
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The lock is not held when calling this function, so we
shouldn't drop then reacquire it.
Based upon a report from Jim MacBaine.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Vincent Sanders
When building the mx1ads ARM platforms the serial driver fails to compile
with GCC 4.01 due to extern/static ambiguity.
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This change removes a bogus error message from the IOC4 serial driver
interrupt handler.
This error message is bogus for two reasons. First, it can never occur
given that current code takes care to initialize IOC4 in such a way that
these "unknown" interrupts could never occur. Second, this code fails to
take into account that other drivers can share the IOC4 interrupt mechanism
through SA_SHIRQ, and thus this driver is not in-fact "all-knowing".
Finally, this error message triggers every time some "unknown" interrupt
occurs -- it's not rate limited or repetition limited in any way, thereby
effectively denying use of the console device. Given its bogosity in the
first place, it's best to just get rid of it entirely.
Acked-by: Pat Gefre <pfg@sgi.com>
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's pointless to include mach-types.h if you're not going to use
anything from it. These references were removed as a result of:
grep -lr 'asm/mach-types\.h' . | xargs grep -L 'machine_is_\|MACH_TYPE_\|MACHINE_START\|machine_type'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add new ID to serial_cs.c; the CIS fimware override is available by the
manufacturer at http://www.sierrawireless.com . Remember to name the CIS
binary SW_7xx_SER.cis and to put it into /lib/firmware/
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Patch from Ben Dooks
Fix the following warnings produced from
drivers/char/s3c2410.c.
drivers/serial/s3c2410.c:757: warning: 'clk' may be used uninitialized
drivers/serial/s3c2410.c:756: warning: 'clksrc' may be used uninitialized
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix up some pm_message_t types
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Vincent Sanders
When building the ARM platforms several serial drivers fail to compile
with GCC 4.01 due to extern/static ambiguity.
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the new Freescale 523x processor family to ColdFire
serial driver. Also set different default baud rate for MOD5272
board.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the new RBHMA4500 eval board for the TX4938. General update
from the 8250 ancestor of this driver. Replace use of deprecated
interfaces.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rather than hard-coding the platform device IDs, enumerate them.
We don't particularly care about the actual ID we get, just as
long as they're unique.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
asm/segment.h varies greatly on different architectures but is clearly
deprecated. Removing all non-architecture consumers will make it easier
for us to get ride of asm/segment.h all together.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this is the last serial driver not using initcalls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <jeff@uclinux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sunsu had been broken by ->stop_tx/->start_tx API changes.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds type-checking to pm_message_t, so that people can't confuse it
with int or u32. It also allows us to fix "disk yoyo" during suspend (disk
spinning down/up/down).
[We've tried that before; since that cpufreq problems were fixed and I've
tried make allyes config and fixed resulting damage.]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Base addess register for SMC 1 and 2 are never initialized. This means
that they will not work unless a bootloader already configured them.
The DPRAM already have space reserved, this patch just makes sure the base
addess register is updated correctly on initialization.
Signed-off-by: Rune Torgersen <runet@innovsys.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
use schedule_timeout instead of direct call to schedule
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 2nd serial port on the MPC8560 ADS was not being configured correctly
and thus could not be used as a console. Updated the defconfig for the
board to configure the proper SCC channel for the 2nd serial port.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pre-format the IO part of the ttyS printks, and prefix them with
KERN_INFO to avoid bootsplash corruption.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems we can simply kill these dummies with this patch.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch adds support for setting and getting RTS / CTS via
set_mtctrl / get_mctrl functions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The start_tx and stop_tx methods were passed a flag to indicate
whether the start/stop was from the tty start/stop callbacks, and
some drivers used this flag to decide whether to ask the UART to
immediately stop transmission (where the UART supports such a
feature.)
There are other cases when we wish this to occur - when CTS is
lowered, or if we change from soft to hard flow control and CTS
is inactive. In these cases, this flag was false, and we would
allow the transmitter to drain before stopping.
There is really only one case where we want to let the transmitter
drain before disabling, and that's when we run out of characters
to send.
Hence, re-jig the start_tx and stop_tx methods to eliminate this
flag, and introduce new functions for the special "disable and
allow transmitter to drain" case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
extern declaration followed by static in drivers/serial/m32r_sio.c
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AMBA_PL010 is broken on arm/versatile; marked as such
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixed problems so we can build with gcc-4.0.1
Signed-off-by: Peter Schaefer-Hutter <peter.schaefer-hutter@tfk-racoms.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Makes dpram allocations work
* Makes non-console UART work on both 8xx and 82xx
* Fixed whitespace in files that were touched
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Pantelis Antoniou <panto@intracom.gr>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Add support for UARTs in MMIO space and clean up a little whitespace.
HP legacy-free ia64 machines need this.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the product-id-string contains the '+' , '&' ,'_', it was not converted
properly from the /etc/pcmcia/config(pcmcia-cs config file).
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
m8xx_cpm_hostalloc() can't rely on using the coherent DMA allocator early
on boot because the VM is not fully up yet. Change it to use the on-board
DPRAM instead.
The current code relies on the "bootmem_page" allocated by
m8xx_cpm_reset(), which must be killed.
This is done in v2.4 but has never been forward ported to v2.6.
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Cc: Pantelis Antoniou <panto@intracom.gr>
Cc: Kumar Gala <kumar.gala@freescale.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the MRi PCIDS1 dual port serial card. This card is a
little controversial since it is the subject of a PCI vendor/device ID
clash. (See
http://www.ussg.iu.edu/hypermail/linux/kernel/0303.1/0516.html). I have
for now just used the hex ID 0x950a. The divisor was part calculated part
iterated, so may not be exactly correct (but works for me at all settings
between 300 - 115300 bps).
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- updates the version
- fix mixing of declarations and code. The mixing of declarations and
code displays warnings when used against RedHat RHEL4.0 distro (compiler
version is 3.4.3-22.1) and hence I separated them out.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The jsm driver uses a static number of 253. The major number 253 is a
reserved for "LOCAL/EXPERIMENTAL USE" by both char and block devices. So
take advantage of the dynamic allocation of major number by the kernel.
Signed-off-by: V. Ananda Krishnan <mansarov@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert parport_serial to use the new 8250_pci interface, converting
the table to a pciserial_board table. This also unuses the SPCI_*
definitions in serialP.h, which can now be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Re-jig the setup/removal/suspend/resume of 8250 pci ports so that they
know slightly less about how they're attached to a PCI device. Expose
this as the new interface for registering PCI serial ports, as well as
the pciserial_board structure and associated flag definitions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pass the serial_private structure via the setup method instead of
the pci_dev. We don't want to assume that the pci_dev's driver
data is a pointer to serial_private. Instead, put the pci_dev
inside serial_private.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Collapse all the SIIG quirk entries into one. SIIG10x cards all
have PCI device IDs of 0x10xx, SIIG20x cards all have PCI device
IDs of 0x20xx.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The 68328serial.c driver has a weird local reimplementation of
magic sysrq. The code is architecture specific enough that calling
machine_restart() is probably ok. But there is no reason not to call
emergency_restart() so do so.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for SIIG Quartet Serial card. This card has Oxford
Semiconducor 16954 quad UART which is clocked by 10x faster
(18.432 MHz) quartz.
Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Use platform device for the 16500 UARTs in the onboard
SuperIO controller.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
changing CONFIG_LOCALVERSION rebuilds too much, for no appearent reason.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Russell King