For some reason the include header wasn't changed from v4l2-i2c-drv-legacy.h
to v4l2-i2c-drv.h in the previous patch. This is now corrected.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Thanks to Steve Toth from Hauppauge with providing me with the information
needed to add support for these models.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When an I2C message specifies a write then a read from the same I2C address,
we need to tell the chip to not release the bus between the message parts.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It seems that the DTV78 firmware is intended for use in locations where
VHF channels have 7MHz bandwidth and UHF channels have 8MHz bandwidth.
If we switch to DTV78 firmware when we detect this condition, we can
avoid firmware reloads when switching between VHF and UHF transponders.
Place the state for this in the control structure so that card drivers
can hint to us to use DTV78 firmware from the first tuning attempt.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We have been inserting a mystery 500kHz offset for tuning 7MHz channels,
however some experimentation reveals it is only needed under certain
conditions with specific firmware combinations. Document these and only
apply the offset when we know it is required.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When searching for the right S-Code table to load, check the HAS_IF flag
against the firmware we are checking instead of against the the "type"
requested. We already ignore the scode type requested if the caller passed
an int_freq; this makes the search by frequency consistent with that behaviour.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Don't modify the control structure that was provided at attach when applying
an offset to the S-Code, otherwise it will be incorrect on subsequent tunes.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add "int_freq" to the debugging output when selecting firmware and the
HAS_IF flag when dumping firmware during load.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The patch below adds the "Pinnacle Dazzle DVC 100" to the list of
cards supported by the em28xx driver. As the configuration is the same
as the DVC 90 one, it simply adds a new USB ID to the list of devices
supported by the DVC 90 configuration.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ensure that the audio is muted at attach-time
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
struct tuner holds state for tuner-core, only -- move it into tuner-core.c
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
replace tda9887_info and tda9887_dbg printk macros with
tuner_info and tuner_dbg, defined in tuner-i2c.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use TUNER_SET_CONFIG to set configuration in tda9887's private state
structure, rather than storing tda9887-specific configuration within
struct tuner.
Update handling of TUNER_SET_CONFIG by tuner-core, to call
&t->fe.ops.analog_demod_ops rather than &t->fe.ops.tuner_ops
analog_demod_ops.set_config passes the request to tuner_ops.set_config,
so this does not break other drivers.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Prevent us from wasting some extra bytes of memory
Thanks to Trent Piepho, for pointing this out.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The auto selection of pertinent helper chips (VIDEO_HELPER_CHIPS_AUTO)
should select the wm8775 driver, which is used by at least one
Conexant 2388x based card (Hauppauge HVR-1300), if VIDEO_CX88 is
selected.
Signed-off-by: Frej Drejhammar <frej.drejhammar@gmail.com>
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
All cx2388 boards need the line-in audio to be routed from an external ADC
(refered to as "ADC mode" in the spec sheet), since the chip is uncapable
of dealing with baseband audio directly.
So... this patch enables normal mode when using the tuner (TV or Radio), and
enables ADC mode with any other source. It'll probably only work with boards
that have supported ADCs (such as the Wolfson wm9775)
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We should not mute the audio input when we stop the codec,
because it will interfere with the live uncompressed stream.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix lack of audio on the MPEG-2 stream of wm8775 based blackbirds.
The wm8775 module initializes the audio input at "route 2", which doesn't
hold true for all boards. The HVR-1300, for example, uses route 1 for
tuner audio, and route 2 for baseband. So we must route the audio to the
proper input depending on what video input is being used.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the unnecessary BLACKBIRD_UNMUTE calls to the mpeg encoder in
cx88-blackbird.c
The encoder is never muted, hence unmuting should then only be necessary
once after hardware initialization.
I tested this from warm boots and cold boots (with long power down time
to ensure the sram in the chip is emptied), and found that after the
firmware upload the encoder is apparently not muted, making the unmutes
unnecessary.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch should fix the 'muted audio' and 'raspy audio' problem for
mpeg2 streams out of cx88-blackbird devices.
Especially mythtv users would find that the audio would often sound bad
(aliased, or 'raspy'), mainly related to channel changes, many (all?)
other users would find that there was no audio at all in the mpeg data
from the encoder chip, unless the audio was manually unmuted.
The patch includes the following modifications:
Don't actually start the mpeg2 encoder until the device is read from
by the application.
Wait until the audio is stable for at least 400ms before starting the
mpeg encoder.
Mute/Unmute the audio when starting/stopping the mpeg encoder.
Stop the mpeg encoder when changing parameters and when changing tuner
frequency.
Add a variable 'mpeg_active' to struct cx8802_dev to allow tracking of
whether or not the mpeg2 encoder is active.
Load the firmware on cx88-blackbird driver load.
Signed-off-by: Jelle Foks <jelle@foks.8m.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ATSC standard-specific firmware is D2633 on both v2.5 and v2.7. Better to
auto-select this firmware, overriding ctrl.d2633.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
On the s5h1409 demod, the IF frequency for VSB is limited to 44 / 5.38 MHz.
Hardcode VSB IF frequency within the driver to 44 / 5.38 MHz.
QAM IF frequency remains configurable via attach-time configuration.
Acked-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The ctrlUrbLock has all it's users commented out, and so it's unused. This
patch removes it.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are a few error paths which don't unlock the usbvision->lock.
So I've added mutex_unlock() calls to fix those paths.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
drivers/media/video/et61x251/et61x251_core.c:390: warning: 'et61x251_i2c_read' defined but not used
drivers/media/video/et61x251/et61x251_core.c:397: warning: 'et61x251_i2c_write' defined but not used
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If we pass TDA18271_GATE_DIGITAL into tda18271_attach(), it will always try to
use the digital demodulator's i2c gate.
If we pass TDA18271_GATE_ANALOG into tda18271_attach(), it will always try to
use the analog demodulator's i2c gate.
If we pass TDA18271_GATE_AUTO into tda18271_attach(), it will try to use the
analog demodulator's i2c gate when tuning in analog mode, and it will try to
use the digital demodulator's i2c gate when tuning in digital mode.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Those newer functions are used by saa7134-empress. Adds export for them:
+EXPORT_SYMBOL_GPL(saa7134_g_ctrl);
+EXPORT_SYMBOL_GPL(saa7134_s_ctrl);
+EXPORT_SYMBOL_GPL(saa7134_queryctrl);
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7134 were converted to video_ioctl2, but saa7134_empress weren't. This broke
saa7134-empress, since it were dependent of saa7134_common_ioctl.
With the conversion, the module had a size decrease of 436 bytes on x86_64:
text data bss dec hex filename
5196 4912 4 10112 2780 old/saa7134-empress.ko
4760 4912 4 9676 25cc new/saa7134-empress.ko
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
VBI were broken, since there weren't any function handlers for it. This patch
fixes it, by removing the vbi_template, using, instead video_template.
This also saves some space at the data segment.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some functions are used also by saa7134-empress, and need to be exported. To
avoid namespace confusion, rename all of them to saa7134_
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Don't waste 128 bytes of memory for a name that might not actually need it.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix codingstyle issue discovered after using new checkpatch.pl
ERROR: open brace '{' following struct go on the same line
396: FILE: linux/drivers/media/video/tda8290.h:24:
+struct tda829x_config
+{
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Store the analog demodulator name in fe.ops.analog_demod_ops.info.name
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- remove dependency of tda8290 module on struct tuner
- move tuner_foo printk macros from tuner-driver.h into tuner-core.c
- clean up #includes of tuner-i2c.h / tuner-driver.h
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Always call tda829x_release if tda829x_attach fails for a reason
other than failure to allocate memory for private structure.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We can tell whether we are tuning television or radio by testing for
struct analog_parameters *params->mode == V4L2_TUNER_RADIO
There is no longer any need for separate set_tv_freq and
set_radio_freq functions in the analog tuner demodulator modules.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix "warning: Using plain integer as NULL pointer".
Convert 'x < y ? x : y' to use min() instead.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver tries to keep all device specific attributes in a
single data structure in one source file. This change further cleans
up how that table is set up. We now try to group everything together
for each specific device, and the number of symbols exported from this
module has now been reduced to a single global.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the AVerMedia EZMaker PCI Deluxe and update the ivtv cardlist.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Manually fixed all pertinent checkpatch.pl errors inside the source code.
Also removed some unused code at the driver and a few minor cleanups.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
mv_count is a counter used to move the vertical bars. Before this patch, it
where a static var. This works fine for just one device. However, when using
multiple devices, every device would increment it.
This patch moves it to its correct place: struct vivi_dev. So, now, each device
has its own data.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now, it is possible to open multiple vivi devices, by using n_devs parameter.
This makes vivi driver closer to a real one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were a trouble at vivi driver when using non-zero inodes. This where due
to not properly preserving the minor inode after calling video_register. Since
this driver is a reference for newer drivers, and it is possible to have more
than one video device inside the machine, this patch makes vivi to dynamically
allocate video_device struct.
Thanks to Gregor Jasny <jasny@vidsoft.de> for pointing the issue.
Also, this patch removes a very anoying (but useless) message of not having a
proper release call.
CC: Gregor Jasny <jasny@vidsoft.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch enabled the IR remote control for the Avermedia M102 (card=110),
which appears to be the same IR as the already supported device on the
Avermedia AVerTV GO 007 FM (card=57) model, the code is two one liners which
enable the IR for this device (subsystem: 1461:f31e)
Signed-off-by: Albert Graham <agraham@g-b.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
dont just copy-and-paste stuff.
(compile-tested this time)
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert v4l from nopage to fault.
Remove redundant vma range checks.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx25840_read4 reads a little-endian 32-bit value whereas cx25840_write4 writes
the 32-bit value as big-endian. Convert write4 to use little-endian as well
(that's the correct endianness).
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After this patch, the order of the functions will be the same as before the
patch converting the driver to user video_ioctl2. This makes easier to diff
between the previous version and the newer one.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Remove the shadowing 'struct v4l2_chip_ident *chip', since it already exists
and makes the if-statement useless.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ivtv-yuv code clean up & reformat. Includes minor changes to some debug lines.
Also fixes a bug found during the reformatting, which would cause the
incorrect amount of yuv data to be sent to the card if source cropping
coordinates were used.
Apart from the bug-fix, there should be no functional difference to the
previous version.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver was incorrectly reporting that it supported YUV 4:2:2 output, when
it is actually YUV 4:2:0. Though I believe the hardware can be pushed to
4:2:2, we don't currently support that.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Previously, all yuv data written to /dev/video48 had only basic support with
no double buffering to avoid display tearing.
With this patch, yuv frames written to video48 are now handled by the existing
IVTV_IOC_DMA_FRAME framework. As such, the frames are hardware buffered to
avoid tearing, and honour scaling mode & field order options. Unlike the
proprietary IVTV_IOC_DMA_FRAME ioctl, all parameters are controlled by the
V4L2 API.
Due to mpeg & yuv output restrictions being different, their V4L2 output
controls have been separated. To control the yuv output, the V4L2 calls must
be done via video48.
If the ivtvfb module is loaded, there will be one side effect to this merge.
The yuv output window will be constrained to the visible framebuffer area. In
the event that a virtual framebuffer size is being used, the limit to the
output size will be the virtual dimensions, but only the portion that falls
within the currently visible area of the framebuffer will be shown.
Like the IVTV_IOC_DMA_FRAME ioctl, the supplied frames must be padded to 720
pixels wide. However the height must only be padded up the nearest multiple
of 32. This would mean an image of 102 lines must be padded to 128. As long
as the true source image size is given, the padding will not be visible in
the final output.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Interlace mode selection code moved into the frame setup phase, so it's now
run before the frame is loaded into a hardware buffer. Given that it can
affect how a new frame is displayed, it was a bit stupid running it after the
frame was already visible.
A few stray interlace related variables which were linked to individual frames
have now been moved into the yuv_frame_info struct. This means that all
variables linked to a specific frame are in the same place & not scattered.
Minor code reformatting in areas touched by the above changes.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
To reduce the number of display register accesses, the yuv code keeps track of
the current video settings. Should there be a change in any single parameter,
it will update the associated display registers to ensure everything is
displayed correctly.
The existing check also looks at the field order for the video. This is not
required, since field reversal does not require any display register changes.
This patch removes the field order from the check.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Inadvertently missed a line when converting code to new hardware buffering
method. In some circumstances, this would lead to a frame being displayed
using parameters belonging to another frame.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ivtv_yuv_prep_frame is split in smaller code blocks.
Modified yuv buffer handling on the PVR350 itself. We now cycle through all 8
hardware buffers.
With this patch in place, driver behaviour should remain unchanged from the
existing release.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently the yuv output stream buffer is divided into blocks whose size
depend on the broadcast standard selected during the driver init phase.
However, the standard can be changed after the init phase. This effectively
breaks the yuv output stream handler, since it relies on the different yuv
planes being block aligned.
This patch changes the setup, so that the block size is always the same. The
decoder dma function has been modified to cope with the fact that the second
yuv plane may no longer be block aligned. The start of the yuv frame must
still be at the beginning of a block, so the stream write function has also
been modified to ensure this is always true.
Also, the stream write function will now initiate a yuv dma transfer as soon
as a full frame is ready. It will not wait until the current write request
has completed, or the stream buffer becomes full.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
pvrusb2: When a per-device-type default video standard is declared,
handle it in such a way that it can be correctly and unambiguously
reported in the system log.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
pvrusb2: Eliminate use of volatile in pipeline control state
variables. These were all cases of paranoia; upon further review the
overall mechanism employed here should not require use of volatile.
This had originally been done out of paranoia, and I have since been
convinced that the paranoia is not required.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
pvrusb2: Remove use of volatile for command sequencer; these variables
are set by interrupt-context code and we check their state in such a
manner that there should be no race conditions. This had originally
been done out of paranoia, and I have since been convinced that the
paranoia is not required.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This adds a default video standard setting to the pvr2_device_desc
structure for describing device types. With this change it is
possible to set a reasonable default standard based on device type.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This changeset allows the pvrusb2 driver to operate a new device type
("GOTVIEW USB2.0 DVD2"). Changes amount to defining a new routing
scheme for the device and adding appropriate table entries into
pvrusb2-devattr.c.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver has been successfully recovering from a crashed
encoder now for over 2 years. I think it's time to reduce the
perceived severity of the warning message. While I'd still very much
like to stop these crashes, the recovery logic is solid enough that
the problem is effectively benign. No point in panicing the users
over it.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
For Hauppauge 24xxx devices, the IR receiver is a custom piece of
logic that is very specific to the device. The pvrusb2 driver can
virtualize this to make it look like a more normal IR receiver found
in other Hauppauge devices. The decision of whether or not to enable
this virtualization however is a device-specific attribute, thus this
changeset.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The exact routing of video and audio signals within a device is a
device-specific attribute. Hauppauge devices do it one way; other
types of device may route things differently. Unfortunately it is
rather impractical to define chip-specific routing at the device
attribute level, so instead what happens here is that "schemes" are
defined. Each chip level interface implements its part of a given
scheme and the scheme as a whole is made into a device specific
attribute controlled via a table entry in pvrusb2-devattr.c. The only
scheme defined here is for Hauppauge devices, but clearly this opens
the door for other possibilities to follow.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Arrange so that the pvrusb2 driver can optionally work without a
Hauppauge ROM being present - which is fairly important for devices
that happen to not come from Hauppauge. The expected existence of a
Hauppauge ROM is now a device attribute. The tuner type is now also a
device attribute, which is consulted if there is no ROM.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Correctly mark when a tuner type is set. Report more faithfully
information about known supported device video standards.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement additional pvrusb2 device info table entries for a device
identifier and a device description. Export this information via the
driver's internal API. Make this information available via the sysfs
driver interface. Also propagate this information into the v4l2
capability structure. An app can now retrieve and report a
descriptive string about the particular type of hardware device it is
operating.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Device-specific driver behavior is now defined by generic device
characteristics rather than by specific device model information.
With this change, the hardware type field can go away, thus this
change.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver currently supports two variants of the Hauppauge
PVR USB2. However there are other hardware types potentially
supportable, but the driver at the moment is not structured to make it
easy to describe these minor variations. This changeset is the first
set of changes to make such additional device support possible.
Device attributes are held in several tables all contained within
pvrusb2-devattr.c; all other device-specific driver behavior now
derives from these tables.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a new implementation for video pipeline control within the
pvrusb2 driver. Actual start/stop of the pipeline is moved to the
driver's kernel thread. Pipeline stages are controlled autonomously
based on surrounding pipeline or application control state. Kernel
thread management is also cleaned up and moved into the internal
control structure of the driver, solving a set up / tear down race
along the way. Better failure recovery is implemented with this new
control strategy. Also with this change comes better control of the
cx23416 encoder, building on additional information learned about the
peculiarities of controlling this part (this information was the
original trigger for this rework). With this change, overall encoder
stability should be considerably improved. Yes, this is a large
change for this driver, but due to the nature of the feature being
worked on, the changes are fairly pervasive and would be difficult to
break into smaller pieces with any semblence of step-wise stability.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently the saa7134 chips only have mute support for the TV input.
Cards with mute from external audio muxes are already fine on the
other inputs and some recent tuners mute at least the radio on exit.
But these mostly hybrid tuners are not fully backward compatible, since
they must power down and mute regardless.
For some included above, the MD7134 knows several, to switch on mute/automute
to the TV input is functional and backward compatible for the applications,
except that the tuners with tda9887 always mute on exit.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
DVB-S is not supported. Also, there are some QAM6 firmwares for xc3028, but it
is reported that this doesn't work fine.
Thanks to Manu Abraham, Michael Krufky and Patrick Boettcher for their
insights.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Force tuner init after attach, then sleep until use.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A previous patch implemented support for non-OFDM digital TV. However, the
previous bandwidth ofdm parameter were left at the code by mistake.
Thanks to Michael Krufky and Patrick Boettcher for noticing this mistake.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
s-code tables are related to IF frequency used for video demodulation.
The s-codes for analog are automatically loaded, according with video standard.
However, for digital, they will depend on the IF of the demoduler chip. IF of
the demoduler.
Before this patch, only a few IF's where possible to use. This patch allows
selecting any IF defined at firmware file.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since check_firmware is called via analog or digital set freq routines, move
type selection to those routines. This avoids having several if's at the code,
and simplifies the source code.
A sideback effect is that implementing radio and other dvb types will become
simpler.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
move some tv-audio initialization code out of tvaudio thread,
and call it on resume too.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
First the saa7134_initdev waits between saa7134_hwinit1
and saa7134_hwinit2 , thus it is probably wise to do the same in saa7134_resume
some hardware probably needs this.
Call saa7134_irq_video_signalchange in .resume like in saa7134_resume to make
saa7134_resume mirror perfectly the saa7134_initdev although
this call isn't strictly necessary in the saa7134_initdev,
but it won't harm anyway.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
*dev->insuspend = 1 should be set before synchronize_irq
*ACK interrupts after synchronize_irq, to make sure there aren't
pending interrupts.
*Add barrier before we restart interrupts so the handler will 100%
see the dev->insuspend
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
pci_save_state should be called before pci_set_power_state
and pci_restore_state after pci_set_power_state
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch removes a few remainders of the VID_HARDWARE_* removal.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
643d01fb38b6f376cced035549f4e193018776e7
On some cases, xc2028/xc3028 wents into "turn off" mode. It seems that this
happens when very weak signals are tuned. To solve this, specific standard
reaload were done previously. Christopher patches changed this behavior to a
complete firmware reload.
This patch removes the hack. A much cleaner solution for this trouble is just
to sent a xc2028/3028 software reset.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
xc3028 can be used on some DTV only designs (for example, DVB-S boards). Before
this patch, a DTV only board would need to call set_tuner_config callback.
This patch allows to optionally pass a xc3028_ctrl parameter, via xc3028_config
struct, fully initializing the driver for DTV.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Xc2028.3028 has two type of firmwares: audio-standard specific ones and
baseband MTS firmwares. MTS firmwares provide stereo decoding for 6 MHz
BTSC/EIAJ and for monoaural audio decoding on 8 MHz firmwares.
It seems that the option to use MTS or a standard-specific audio decoding
depends on the way xc2028/3028 is connected.
Instead of wasting 32 (or 64 bits) to signalize if the driver needs to use MTS
firmware, this patch converts it to a bitfield that can be shared with other
proprieties of xc2028/3028.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some drivers call set_frequency before selecting the video standard. Before
this patch, an invalid standard ID could be assumed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When loading init1 firmware, there may not be an 8MHz specific version.
Load the non-8MHz version if it exists.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When searching for standard-specific analog firmware, only certain
type bits are valid, much like for DTV. Mask them off when finding
the firmware to load.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When loading BASE firmware, we must use std = 0.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add sleep method to enable putting the tuner into standby mode.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In practice, the tuner occasionally fails to respond correctly after a
firmware load. Retry the firmware load if the firmware/hardware version
we read back from the tuner after programming does not match what we
expect.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Define a list of valid "firmware types" for each combination of BASE,
DTV and SCODEs. By masking the appropriate firmware bits off we can
just use one "type" for the firmware searching and also flag when we
are looking for a BASE, DTV or SCODE type firmware. This makes it
much easier to track if we need to change device modes or flash an
individual firmware part.
Add a structure to remember what firmware properties we have. This
contains the currently loaded/wanted base firmware (type), video std
(id), video std requested (std_req), scode file and number in use.
Incorporate said structure into the tuner private data.
When checking whether the current firmware needs to be reloaded, first
figure out exactly what "type" of firmware we want (base, std and
scode), and then proceed to load the appropriate matching base,
std-specific and scode records iff there are any changes required.
This removes guesswork from the process because we no longer need to
individually code a check for every tuning parameter's interactions.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a bit to select D2633 DTV firmware to struct xc2028_ctrl, so that it can
be enabled via .set_config.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When validating and loading SCODE firmware we need to take into account the
two-byte size header before each entry.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rather than picking the first video standard firmware that supports any of
the standards that the user has requested, try to select one that supports
as many of them as possible. This improves the likelihood that the firmware
we select will support the user's desired TV standard.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There is no need to duplicate the max_len field from the ctrl structure
in the private data. If we use it directly from priv->ctrl, we can memcpy
the structure (apart from strings) to reduce maintenance as it grows.
Enforce a minimum max_len length of 8 data bytes (+ 1 address byte) as seems
to be required by the tuner.
Also, use kstrdup instead of open coding the string duplication.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
7MHz bandwidth DVB-T needs an adjusted offset at the PLL to ensure the IF
output is correctly centered.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We were using priv->bandwidth to select the base firmware to load, not the
requested bandwidth value, oops. Also, 7MHz Digital TV needs 8MHz base
firmware loaded.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The frequency divisor should only be four bytes long. Also, display the
frequency and divisor correctly in the debug output.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Hans Verkuil