* 'fixes' of master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: footbridge: fix clock event support
ARM: footbridge: fix debug macros
ARM: initrd: disable initrds outside of memory
ARM: extend Code: line by one 16-bit quantity for Thumb instructions
ARM: 6955/1: cmpxchg syscall should data abort if page not write
ARM: 6954/1: zImage: fix Thumb2 breakage
ARM: 6953/1: DT: don't try to access physical address zero
ARM: 6949/2: mach-u300: fix compilaton warning in IO accessors
Revert "ARM: 6944/1: mm: allow ASID 0 to be allocated to tasks"
Revert "ARM: 6943/1: mm: use TTBR1 instead of reserved context ID"
davinci: make PCM platform devices static
arm: davinci: Fix fallout from generic irq chip conversion
ARM: 6894/1: mmci: trigger card detect IRQs on falling and rising edges
ARM: 6952/1: fix lockdep warning of "unannotated irqs-off"
ARM: 6951/1: include .bss in memory layout information
ARM: 6948/1: Fix .size directives for __arm{7,9}tdmi_proc_info
ARM: 6947/2: mach-u300: fix compilation error in timer
ARM: 6946/1: vexpress: move v2m clock init to init_early
ARM: mx51/sdma: Check the chip revision in run-time
arm: mxs: include asm/processor.h for cpu_relax()
Right now the card detect IRQ for MMCI is requested without any
flags which will give some default machine-specified IRQ
behaviour. However on the U300 rising+falling edges (such as can
be expected from a simple GPIO to generate when inserting/removing
a card) need to be requested explicitly.
Cc: Rabin Vincent <rabin.vincent@stericsson.com>
Cc: Ulf Hansson <ulf.hansson@stericsson.com>
Cc: Sebastian Rasmussen <sebastian.rasmussen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
eMMC does not handle power off when not in sleep state,
Skip regulator disable during probe when eMMC is
not in known state - state left by bootloader.
Resolves eMMC failure on OMAP4
mmc0: error -110 whilst initialising MMC card
Signed-off-by: Balaji T K <balajitk@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm: (45 commits)
ARM: 6945/1: Add unwinding support for division functions
ARM: kill pmd_off()
ARM: 6944/1: mm: allow ASID 0 to be allocated to tasks
ARM: 6943/1: mm: use TTBR1 instead of reserved context ID
ARM: 6942/1: mm: make TTBR1 always point to swapper_pg_dir on ARMv6/7
ARM: 6941/1: cache: ensure MVA is cacheline aligned in flush_kern_dcache_area
ARM: add sendmmsg syscall
ARM: 6863/1: allow hotplug on msm
ARM: 6832/1: mmci: support for ST-Ericsson db8500v2
ARM: 6830/1: mach-ux500: force PrimeCell revisions
ARM: 6829/1: amba: make hardcoded periphid override hardware
ARM: 6828/1: mach-ux500: delete SSP PrimeCell ID
ARM: 6827/1: mach-netx: delete hardcoded periphid
ARM: 6940/1: fiq: Briefly document driver responsibilities for suspend/resume
ARM: 6938/1: fiq: Refactor {get,set}_fiq_regs() for Thumb-2
ARM: 6914/1: sparsemem: fix highmem detection when using SPARSEMEM
ARM: 6913/1: sparsemem: allow pfn_valid to be overridden when using SPARSEMEM
at91: drop at572d940hf support
at91rm9200: introduce at91rm9200_set_type to specficy cpu package
at91: drop boot_params and PLAT_PHYS_OFFSET
...
With the addition of the platform device mfd_cell pointer, we can now
cleanly pass the sub device drivers platform data pointers through the
regular device platform_data one, and get rid of mfd_get_data()
Cc: Ian Molton <spyro@f2s.com>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Acked-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
ST-Ericsson modified ARM PrimeCell PL180 block has not got
an updated corresponding amba-id, althought the IP block has
changed in db8500v2. The change was done to the datactrl register.
Using the overrided subversion ID, account for this.
Signed-off-by: Philippe Langlais <philippe.langlais@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (75 commits)
mmc: core: eMMC bus width may not work on all platforms
mmc: sdhci: Auto-CMD23 fixes.
mmc: sdhci: Auto-CMD23 support.
mmc: core: Block CMD23 support for UHS104/SDXC cards.
mmc: sdhci: Implement MMC_CAP_CMD23 for SDHCI.
mmc: core: Use CMD23 for multiblock transfers when we can.
mmc: quirks: Add/remove quirks conditional support.
mmc: Add new VUB300 USB-to-SD/SDIO/MMC driver
mmc: sdhci-pxa: Add quirks for DMA/ADMA to match h/w
mmc: core: duplicated trial with same freq in mmc_rescan_try_freq()
mmc: core: add support for eMMC Dual Data Rate
mmc: core: eMMC signal voltage does not use CMD11
mmc: sdhci-pxa: add platform code for UHS signaling
mmc: sdhci: add hooks for setting UHS in platform specific code
mmc: core: clear MMC_PM_KEEP_POWER flag on resume
mmc: dw_mmc: fixed wrong regulator_enable in suspend/resume
mmc: sdhi: allow powering down controller with no card inserted
mmc: tmio: runtime suspend the controller, where possible
mmc: sdhi: support up to 3 interrupt sources
mmc: sdhi: print physical base address and clock rate
...
CMD19 -- The offical way to validate bus widths from the JEDEC spec
does not work on all platforms. Some platforms that use PCI/PCIe
to connect their SD controllers are known to fail.
If the quirk MMC_BUS_WIDTH_TEST is not defined we try to figure out
the bus width by reading the ext_csd at different bus widths and
compare this against the ext_csd read in 1 bit mode. If no ext_csd
is available we default to 1 bit operations.
Code has been tested on mmp2 against 8 bit eMMC and Transcend 2GB
card that is known to not work in 4 bit mode. The physical pins
on the card are not present to support 4 bit operation.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Enables Auto-CMD23 support where available (SDHCI 3.0 controllers)
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Tested-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SD cards operating at UHS104 or better support SET_BLOCK_COUNT.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Implements support for multiblock transfers bounded
by SET_BLOCK_COUNT (CMD23).
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
CMD23-prefixed instead of open-ended multiblock transfers
have a performance advantage on some MMC cards.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add a driver for Elan Digital System's VUB300 chip which is a USB
connected SDIO/SDmem/MMC host controller. A VUB300 chip enables a USB 2.0
or USB 1.1 connected host computer to use SDIO/SD/MMC cards without the
need for a directly connected, for example via PCI, SDIO host controller.
Signed-off-by: Anthony F Olech <tony.olech@elandigitalsystems.com>
[cjb: various punctuation and style fixes]
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
32 Bit DMA/ADMA Access
32 Bit Size
Support ADMA End Descriptor in current chain
(no need for dummy entry)
Signed-off-by: Philip Rakity <prakity@marvell.com>
Tested-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
mmc_rescan_try_freq() tries to init two times with the last frequency.
For example, if host->f_min is 400KHz, we see the message below:
mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz
mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz
Andy Ross says that he didn't try this code on a board with an f_min
that exactly matches one of the table entries, which explains why the
bug wasn't detected.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Andy Ross <andy.ross@windriver.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
eMMC voltage change not required for 1.8V. 3.3V and 1.8V vcc
are capable of doing DDR. vccq of 1.8v is not required.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
eMMC chips do not use CMD11 when changing voltage. Add extra
argument to call to indicate if CMD11 needs to be sent.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Marvell controller requires 1.8V bit in UHS control register 2
be set when doing UHS. eMMC does not require 1.8V for DDR.
add platform code to handle this.
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allow platform specific code to set UHS registers if
implementation requires speciial platform specific handling
Signed-off-by: Philip Rakity <prakity@marvell.com>
Reviewed-by: Arindam Nath <arindam.nath@amd.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since the MMC_PM_KEEP_POWER flag should be set on each suspend,
it should also cleared on each resume.
Upon resuming, we have to know if power was kept
(for re-initialization, etc.), so clear it just after resuming.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
regulator_enable() was incorrectly placed in the suspend function
instead of the resume function.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Will Newton <will.newton@imgtec.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Supply a link to TMIO private data for platforms to implement their
own card detection.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The TMIO MMC controller cannot be powered off to save power, when no
card is plugged in, because then it will not be able to detect a new
card-insertion event. On some implementations, however, it is
possible to switch to using another source to detect card insertion.
This patch adds support for such implementations.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Convert the SDHI code to support more than a single interrupt source.
Needed to support hardware that uses GIC instead of INTC as interrupt
controller.
Will also allow us to remove the irq forwarding workaround from the
INTC code in the future.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Instead of printing out useless information such as the virtual base
address and one of 4 interrupts, convert the SDHI probe() to print
out physical base address together with clock rate.
We do have a struct device so make use of dev_info().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Modify the SDHI driver to get rid of unwanted irq flags.
IRQF_DISABLED unused, see include/linux/interrupt.h
IRQF_TRIGGER_FALLING only relevant on external IRQ pins,
but since SDHI is internal in the SoC this can go away.
Needed to support SDHI on sh73a0 that comes with a GIC
that errors out with the IRQF_TRIGGER_FALLING setting.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Move request_irq()/free_irq() from the shared code
in tmio_mmc.c into the SDHI/tmio specific portion
in sh_mobile_sdhi.c and tmio_mmc_pio.c.
This is ground work to allow us to adjust the SDHI
code with IRQ flags and number of interupt sources.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The MMC subsystem does not guarantee, that host driver .request() and
.set_ios() callbacks are serialised. Such concurrent calls, however,
do not have to be meaningfully supported, drivers just have to make
sure to avoid any severe problems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Adding support for runtime power-management to the MMCIF driver allows
it to save power as long as no card is present. To also allow to turn
off the power domain at that time, we release DMA channels during that
time, since on some sh-mobile systems the DMA controller(s) and the
MMCIF block belong to the same power domain. System-wide power
management has been tested with experimental PM patches on AP4-based
systems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
Add runtime and system-wide power management to the TMIO MMC driver
in PIO and DMA modes, allowing it to properly save and restore its
state during system suspend. Runtime PM is very crude ATM, because
the controller has to be powered on all the time to detect card
hotplug events.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
The MMC subsystem does not guarantee that host driver .request() and
.set_ios() callbacks are serialised. Such concurrent calls, however,
do not have to be meaningfully supported, drivers just have to make
sure to avoid any severe problems.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Simon Horman <horms@verge.net.au>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Chris Ball <cjb@laptop.org>
If there is only 1 function interrupt registered it is possible to
improve performance by directly calling the irq handler and avoiding
the overhead of reading the CCCR registers.
Signed-off-by: Per Forlin <per.forlin@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@stericsson.com>
Reviewed-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
When allocation of idata failed there was a null dereference. Also avoid
calling kfree where it isn't needed.
Signed-off-by: Vladimir Motyka <vladimir.motyka@gmail.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host Controller v3.00 can support retuning modes 1,2 or 3 depending on
the bits 46-47 of the Capabilities register. Also, the timer count for
retuning is indicated by bits 40-43 of the same register. We initialize
timer_list for retuning the first time we execute tuning procedure. This
condition is indicated by SDHCI_NEEDS_RETUNING not being set. Since
retuning mode 1 sets a limit of 4MB on the maximum data length, we set
max_blk_count appropriately. Once the tuning timer expires, we set
SDHCI_NEEDS_RETUNING flag, and if the flag is set, we execute tuning
procedure before sending the next command. We need to restore mmc_request
structure after executing retuning procedure since host->mrq is used
inside the procedure to send CMD19. We also disable and re-enable this
flag during suspend and resume respectively, as per the spec v3.00.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host Controller v3.00 supports programmable clock mode as an optional
feature. The support for this mode is indicated by non-zero value in
bits 48-55 of the Capabilities register. If supported, the actual
value of Clock Multiplier is one more than the value provided in the
bit fields. We only set Clock Generator Select (bit 5) and SDCLK
Frequency Select (bits 8-15) of the Clock Control register in case
Preset Value Enable is not set, otherwise these fields are automatically
set by the Host Controller based on the UHS mode selected. Also, since
the maximum and minimum clock frequency in this mode can be
(Base Clock * Clock Mul) and (Base Clock * Clock Mul)/1024 respectively,
f_max and f_min have been recalculated to reflect this change.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
According to the Host Controller spec v3.00, setting Preset Value Enable
in the Host Control2 register lets SDCLK Frequency Select, Clock Generator
Select and Driver Strength Select to be set automatically by the Host
Controller based on the UHS-I mode set. This patch enables this feature.
Since Preset Value Enable makes sense only for UHS-I cards, we enable this
feature after successfull UHS-I initialization. We also reset Preset Value
Enable next time before initialization.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host Controller needs tuning during initialization to operate SDR50
and SDR104 UHS-I cards. Whether SDR50 mode actually needs tuning is
indicated by bit 45 of the Host Controller Capabilities register.
A new command CMD19 has been defined in the Physical Layer spec
v3.01 to request the card to send tuning pattern.
We enable Buffer Read Ready interrupt at the very begining of tuning
procedure, because that is the only interrupt generated by the Host
Controller during tuning. We program the block size to 64 in the
Block Size register. We make sure that DMA Enable and Multi Block
Select in the Transfer Mode register are set to 0 before actually
sending CMD19. The tuning block is sent by the card to the Host
Controller using DAT lines, so we set Data Present Select (bit 5) in
the Command register. The Host Controller is responsible for doing
the verfication of tuning block sent by the card at the hardware
level. After sending CMD19, we wait for Buffer Read Ready interrupt.
In case we don't receive an interrupt after the specified timeout
value, we fall back on fixed sampling clock by setting Execute
Tuning (bit 6) and Sampling Clock Select (bit 7) of Host Control2
register to 0. Before exiting the tuning procedure, we disable Buffer
Read Ready interrupt and re-enable other interrupts.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Since only UHS-I cards respond with S18A set in response to ACMD41,
we set the card as ultra-high-speed after successfull initialization.
We need to decide whether a card is SDXC based on the C_SIZE field
of CSDv2.0 register. According to Physical Layer spec v3.01, the
minimum value of C_SIZE for SDXC card is 00FFFFh.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
We decide on the current limit to be set for the card based on the
Capability of Host Controller to provide current at 1.8V signalling,
and the maximum current limit of the card as indicated by CMD6
mode 0. We then set the current limit for the card using CMD6 mode 1.
As per the Physical Layer Spec v3.01, the current limit switch is
only applicable for SDR50, SDR104, and DDR50 bus speed modes. For
other UHS-I modes, we set the default current limit of 200mA.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for setting UHS-I bus speed mode during UHS-I
initialization procedure. Since both the host and card can support
more than one bus speed, we select the highest speed based on both of
their capabilities. First we set the bus speed mode for the card using
CMD6 mode 1, and then we program the host controller to support the
required speed mode. We also set High Speed Enable in case one of the
UHS-I modes is selected. We take care to reset SD clock before setting
UHS mode in the Host Control2 register, and then re-enable it as per
the Host Controller spec v3.00. We then set the clock frequency for
the UHS-I mode selected.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
As per Host Controller spec v3.00, we reset SDCLK before setting
High Speed Enable, and then set it back to avoid generating clock
gliches. Before enabling SDCLK again, we make sure the clock is
stable, so we use sdhci_set_clock().
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
This patch adds support for setting driver strength during UHS-I
initialization procedure. Since UHS-I cards set S18A (bit 24) in
response to ACMD41, we use this as a base for UHS-I initialization.
We modify the parameter list of mmc_sd_get_cid() so that we can
save the ROCR from ACMD41 to check whether bit 24 is set.
We decide whether the Host Controller supports A, C, or D driver
type depending on the Capabilities register. Driver type B is
suported by default. We then set the appropriate driver type for
the card using CMD6 mode 1. As per Host Controller spec v3.00, we
set driver type for the host only if Preset Value Enable in the
Host Control2 register is not set. SDHCI_HOST_CONTROL has been
renamed to SDHCI_HOST_CONTROL1 to conform to the spec.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
SD cards which conform to Physical Layer Spec v3.01 can support
additional Bus Speed Modes, Driver Strength, and Current Limit
other than the default values. We use CMD6 mode 0 to read these
additional card functions. The values read here will be used
during UHS-I initialization steps.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Host Controller v3.00 adds another Capabilities register. Apart
from other things, this new register indicates whether the Host
Controller supports SDR50, SDR104, and DDR50 UHS-I modes. The spec
doesn't mention about explicit support for SDR12 and SDR25 UHS-I
modes, so the Host Controller v3.00 should support them by default.
Also if the controller supports SDR104 mode, it will also support
SDR50 mode as well. So depending on the host support, we set the
corresponding MMC_CAP_* flags. One more new register. Host Control2
is added in v3.00, which is used during Signal Voltage Switch
procedure described below.
Since as per v3.00 spec, UHS-I supported hosts should set S18R
to 1, we set S18R (bit 24) of OCR before sending ACMD41. We also
need to set XPC (bit 28) of OCR in case the host can supply >150mA.
This support is indicated by the Maximum Current Capabilities
register of the Host Controller.
If the response of ACMD41 has both CCS and S18A set, we start the
signal voltage switch procedure, which if successfull, will switch
the card from 3.3V signalling to 1.8V signalling. Signal voltage
switch procedure adds support for a new command CMD11 in the
Physical Layer Spec v3.01. As part of this procedure, we need to
set 1.8V Signalling Enable (bit 3) of Host Control2 register, which
if remains set after 5ms, means the switch to 1.8V signalling is
successfull. Otherwise, we clear bit 24 of OCR and retry the
initialization sequence. When we remove the card, and insert the
same or another card, we need to make sure that we start with 3.3V
signalling voltage. So we call mmc_set_signal_voltage() with
MMC_SIGNAL_VOLTAGE_330 set so that we are back to 3.3V signalling
voltage before we actually start initializing the card.
Tested by Zhangfei Gao with a Toshiba uhs card and general hs card,
on mmp2 in SDMA mode.
Signed-off-by: Arindam Nath <arindam.nath@amd.com>
Reviewed-by: Philip Rakity <prakity@marvell.com>
Tested-by: Philip Rakity <prakity@marvell.com>
Acked-by: Zhangfei Gao <zhangfei.gao@marvell.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Allows appropriately-privileged applications to send CMD (normal) and ACMD
(application-specific; preceded with CMD55) commands to cards/devices on
the mmc bus. This is primarily useful for enabling the security
functionality built in to every SD card.
It can also be used as a generic passthrough (e.g. to enable virtual
machines to control mmc bus devices directly). However, this use case has
not been tested rigorously. Generic passthrough testing was only conducted
for a few non-security opcodes to prove the feasibility of the passthrough.
Since any opcode can be sent using this passthrough, it is very possible to
render the card/device unusable. Applications that use this ioctl must
have CAP_SYS_RAWIO.
Security commands tested on TI PCIxx12 (SDHCI), Sigma Designs SMP8652 SoC,
TI OMAP3621/OMAP3630 SoC, Samsung S5PC110 SoC, Qualcomm MSM7200A SoC.
Signed-off-by: John Calixto <john.calixto@modsystems.com>
Reviewed-by: Andrei Warkentin <andreiw@motorola.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
To avoid lockdep warnings:
BUG: key dc90a520 not in .data!
------------[ cut here ]------------
WARNING: at /home/rabin/kernel/arm/kernel/lockdep.c:2701 sysfs_add_file_mode+0x4c/0xb0()
Modules linked in:
[<c004b5d8>] (unwind_backtrace+0x0/0xe4) from [<c0074f20>] (warn_slowpath_common+0x4c/0x64)
[<c0074f20>] (warn_slowpath_common+0x4c/0x64) from [<c0074f50>] (warn_slowpath_null+0x18/0x1c)
[<c0074f50>] (warn_slowpath_null+0x18/0x1c) from [<c0157fec>] (sysfs_add_file_mode+0x4c/0xb0)
[<c0157fec>] (sysfs_add_file_mode+0x4c/0xb0) from [<c02d61e4>] (mmc_add_disk+0x40/0x64)
[<c02d61e4>] (mmc_add_disk+0x40/0x64) from [<c02d64cc>] (mmc_blk_probe+0x188/0x1fc)
[<c02d64cc>] (mmc_blk_probe+0x188/0x1fc) from [<c02ce820>] (mmc_bus_probe+0x14/0x18)
...
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Chris Ball <cjb@laptop.org>
On HP laptops with JMicron 388 chip, the write-locked SD card isn't
detected correctly as read-only in many cases. This is because the
PRESENT_STATE register becomes unsable just after plugging, and it
returns the WRITE_PROTECT bit wrongly at the first read.
This patch fixes the read-only detection by adding a new sdhci quirk
indicating to check the register more intensively with a relatively
long delay.
The patch is tested with 2.6.39-rc4 kernel.
Cc: Aries Lee <arieslee@jmicron.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chris Ball <cjb@laptop.org>
With the hardware partitions support (which represent additional logical
devices present on MMC), devidx does not correspond with index used to form
/dev/mmcblkX names. So use an additional allocated index for device names.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Linus Torvalds