LEDs modes are set the same way, except they are offset by 4 times the
index of the LED.
Let's factorize all the code so that it's easier to add support for the
4 LEDs of the VSC8584 PHY.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added tx timeout handler. This helps
when troubleshooting.
Signed-off-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following bits in the GUMR is changed for non
tsa mode: CDS, CTSP and CTSS are set to zero.
When set, there is no tx interrupts from the controller.
Signed-off-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ability to set hmask in the device-tree,
which can be used to change address
filtering of packets.
Signed-off-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to avoid discarding ethernet
packets when using HDLC_ETH protocol.
Signed-off-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a need to allow higher indexes to be
able to support MPC83xx platforms. (UCC1-UCC8)
Signed-off-by: David Gounaris <david.gounaris@infinera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Collect descriptors of all ULD and LLD hardware queues managed
by LLD.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
in ndo_set_vf_rate() when max_tx_rate is 0 disable tx
rate limiting for that vf.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous implement, the query operation for fibre port and copper
port are mixed. This patch refines it by seperating them based on the port
type.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the advertised flow control ability has been fetched using
phy_ethtool_ksettings_get() or hclge_get_link_mode() then it is
unnecessary to fetch them again later using hclge_get_flowctrl_adv().
This patch removes it.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the dst mac addr of loopback packet is the same as
the host' mac addr, the SSU component may loop back the packet
to host before the packet reaches mac or serdes, which will defect
the purpose of mac or serdes selftest.
This patch changes it by adding 0x1f to the last byte of dst mac
addr.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently only fiber port checks if it is necessay to set the
mac through firmware when link is changed, this patch unify the
checking to allow the copper port do the checking too.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netdev is down, the stack will delete the vlan from
hardware including vlan0, which will cause problem when
doing loopback selftest when netdev is down.
This patch fixes it by always preserving vlan 0 in hardware,
because vlan 0 is defalut vlan, which should always be in
hardware.
Fixes: c39c4d98dc ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When ping is runnig and user executes the loopback selftest, the
ping cmd will stop and exit.
This patch fixes it by using the hns3_nic_net_open/stop to offline
the netdev when doing loopback selftest.
Fixes: c39c4d98dc ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tqp and mac need to be enabled when doing loopback selftest,
ae_algo->ops->start/stop is used to do the job, there is a
time window between ae_algo->ops->start/stop and loopback setup,
which will cause selftest failed problem when there is frame
coming in during that time window.
This patch fixes it by enabling the tqp and mac during loopback
setup process.
Fixes: c39c4d98dc ("net: hns3: Add mac loopback selftest support in hns3 driver")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements shutdown ops in hns3 pci driver, which
unloads the hns3 driver and set the power state to D3hot.
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PF uses hdev->vlan_table to manage the port vlan table. In function
hclge_set_vlan_filter_hw(), it checks whether a vlan id has been used,
by foreach all the vport bits. It should use macro HCLGE_VPORT_NUM,
not VLAN_N_VID as the foreach condition.
Fixes: 6c251711b3 ("net: hns3: Disable vf vlan filter when vf vlan table is full")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the lower 24 bits of the IPV6 link-local addresses at both
ends are the same, the multicast MAC address for Neigbour Discovery
is the same. The multicast for Neigbour Discovery will fail.
This patch fixes it by including the bonding uplink port in the
multicast group.
Fixes: 46a3df9f9718("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are only 128 entries in vf vlan table, if user has added
more than 128 vlan, fw will ignore it and disable the vf vlan
table. So when user deletes the vlan entry that has not been
set to vf vlan table, fw will return not found result and driver
treat that as error, which will cause vlan delete failed problem.
This patch fixes it by returning ok when fw returns not found
result.
Fixes: 6c251711b3 ("net: hns3: Disable vf vlan filter when vf vlan table is full")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Pradeep Nalla <pradeep.nalla@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the RQs are shared between all pkey interfaces, the stats
should be taken from where the per-ring stats are stored instead
of the parent RQ.
Fixes: 4c6c615e3f ("net/mlx5e: IPoIB, Add PKEY child interface nic profile")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose RX and TX counters by implementing ndo_get_stats64 operation
for child devices.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose RX and TX counters by implementing ndo_get_stats64 operation for
both parent devices.
After this change, all the relevant statistics can be retrieved using
ifconfig.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enhanced ipoib does not initialize max_opened_tc causing wrong ethtool
statistics. As mlx5e_grp_sw_update_stats relies on this variable, without
this change, the TX statistics will not be updated.
Fixes: 05909babce ("net/mlx5e: Avoid reset netdev stats on configuration changes")
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 6352 family has one SERDES interface, which can be used by either
port 4 or port 5. Add interrupt support for the SERDES interface, and
report when the link status changes.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
After changing to the needed page, actually write the value to the
register!
Fixes: 09cb7dfd3f ("net: dsa: mv88e6xxx: describe PHY page and SerDes")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix Kconfig warning with OF_MDIO where OF_MDIO was
selected unconditionally instead of only when
OF is actually enabled.
Fixes 7e8d5755be ("net: nixge: Add support for 64-bit platforms")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Moritz Fischer <mdf@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the loop of mvneta_tx_done_gbe(), we call the smp_processor_id()
each time, move the call out of the loop to optimize the code a bit.
Before the patch, the loop looks like(under arm64):
ldr x1, [x29,#120]
...
ldr w24, [x1,#36]
...
bl 0 <_raw_spin_lock>
str w24, [x27,#132]
...
After the patch, the loop looks like(under arm64):
...
bl 0 <_raw_spin_lock>
str w23, [x28,#132]
...
where w23 is loaded so be ready before the loop.
>From another side, mvneta_tx_done_gbe() is called from mvneta_poll()
which is in non-preemptible context, so it's safe to call the
smp_processor_id() function once.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code and HW supports NETIF_F_RXCSUM, so let's enable it by default.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
napi_gro_receive() checks NETIF_F_GRO bit as well, if the bit is not
set, we will go through GRO_NORMAL in napi_skb_finish(), so fall back
to netif_receive_skb_internal(), so we don't need to check NETIF_F_GRO
ourself.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/broadcom/bgmac.c: In function 'bgmac_dma_alloc':
drivers/net/ethernet/broadcom/bgmac.c:619:6: warning:
variable 'err' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SRAB driver is the default way to communicate with the integrated
switch on iProc platforms and the MMAP driver is the way to communicate
with the integrated switch on DSL BCM63xx and CM BCM33xx.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/cavium/liquidio/request_manager.c: In function 'lio_process_iq_request_list':
drivers/net/ethernet/cavium/liquidio/request_manager.c:383:27: warning:
variable 'irh' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver displays an error message for each unrecognized dcbx TLV that's
received from the peer or configured on the device. It is observed that
syslog will be flooded with such messages in certain scenarios e.g.,
frequent link-flaps/lldp-transactions. Changing the severity of this
message to verbose level as it's not an error scenario/message.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/broadcom/bnxt/bnxt_vfr.c: In function 'bnxt_vf_rep_rx':
drivers/net/ethernet/broadcom/bnxt/bnxt_vfr.c:212:28: warning:
variable 'rx_stats' set but not used [-Wunused-but-set-variable]
struct bnxt_vf_rep_stats *rx_stats;
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
XGMAC2 uses the same CBS mechanism as GMAC5, only registers offset
changes. Lets use the same TC callbacks and implement the .config_cbs
callback in XGMAC2 core.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DPAA2 Ethernet driver supports Freescale/NXP SoCs with DPAA2
(DataPath Acceleration Architecture v2). The driver manages
network objects discovered on the fsl-mc bus.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some boards the interrupt can be shared between multiple devices.
For example on Turris Mox the interrupt is shared between all switches.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Provide a software TX timestamp as well as the ethtool query interface
and report the software timestamp capabilities.
Tested with "ethtool -T" and two linuxptp instances each bound to a
tunnel endpoint.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel Borkmann says:
====================
pull-request: bpf-next 2018-09-01
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add AF_XDP zero-copy support for i40e driver (!), from Björn and Magnus.
2) BPF verifier improvements by giving each register its own liveness
chain which allows to simplify and getting rid of skip_callee() logic,
from Edward.
3) Add bpf fs pretty print support for percpu arraymap, percpu hashmap
and percpu lru hashmap. Also add generic percpu formatted print on
bpftool so the same can be dumped there, from Yonghong.
4) Add bpf_{set,get}sockopt() helper support for TCP_SAVE_SYN and
TCP_SAVED_SYN options to allow reflection of tos/tclass from received
SYN packet, from Nikita.
5) Misc improvements to the BPF sockmap test cases in terms of cgroup v2
interaction and removal of incorrect shutdown() calls, from John.
6) Few cleanups in xdp_umem_assign_dev() and xdpsock samples, from Prashant.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit gets rid of the structure xdp_umem_props. It was there to
be able to break a dependency at one point, but this is no longer
needed. The values in the struct are instead stored directly in the
xdp_umem structure. This simplifies the xsk code as well as af_xdp
zero-copy drivers and as a bonus gets rid of one internal header file.
The i40e driver is also adapted to the new interface in this commit.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
With certain gcc versions, it was possible to get the warning
"'tx_desc' may be used uninitialized in this function" for the
i40e_xmit_zc. This was not possible, however this commit simplifies
the code path so that this warning is no longer emitted.
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
To prevent VF from deleting MAC address that was assigned by the
PF we need to check for that scenario when we try to delete a MAC
address from a VF.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If a VF is being removed, there is no need to continue with the
workqueue sync for the adminq task, thus cancel it. Without this call,
when VFs are created and removed right away, there might be a chance for
the driver to crash with events stuck in the adminq.
Signed-off-by: Lihong Yang <lihong.yang@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Hold the rtnl lock when we're clearing interrupt scheme
in i40e_shutdown and in i40e_remove.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With current implementation of i40evf_set_features when user sets
any offload via ethtool we set I40EVF_FLAG_AQ_ENABLE_VLAN_STRIPPING
as a required aq which triggers driver to call
i40evf_enable_vlan_stripping. This shouldn't take place.
This patches fixes it by setting the flag only when VLAN offload
is turned on.
Signed-off-by: Patryk Małek <patryk.malek@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If our card has been put in an unstable state due to
other drivers interacting with it, speed settings
might be incorrect. If incorrect, forcefully reset them
on open to known default values.
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When XDP is enabled, the driver will report incorrect
statistics. Received frames will reported as transmitted frames.
This commits fixes the i40e implementation of ndo_get_stats64 (struct
net_device_ops), so that iproute2 will report correct statistics
(e.g. when running "ip -stats link show dev eth0") even when XDP is
enabled.
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Fixes: 74608d17fe ("i40e: add support for XDP_TX action")
Signed-off-by: Björn Töpel <bjorn.topel@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Quentin Schulz