Implementation taken from rtl2830.
Cc: Thomas Mair <thomas.mair86@googlemail.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is workaround / partial fix.
rtl2832u_power_ctrl() and rtl2832u_frontend_attach() needs to
be go through carefully and fix properly. There is clearly
some logical errors when handling power-management ang GPIOs...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Cc: Thomas Mair <thomas.mair86@googlemail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Stream did not start anymore after stream was stopped once.
Following error can be seen, xhci_hcd
WARN Set TR Deq Ptr cmd failed due to incorrect slot or ep state.
usb_clear_halt for streaming endpoint helps.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Old i2c message length splitting logic was faulty. Make it better.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I didn't found easy way to handle register dump only when needed so
remove it totally. It is quite useless and trivial function, every
developer could write new one in few minutes when needed.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Changing cached frequency during init is something no-no.
Make it behave a little bit better. After that device could
survive from suspend/resume when streaming is ongoing.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The uvcvideo driver now supports USERPTR, and isn't limited to YUYV and
MJPEG anymore.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ite_dev::rdev is currently initialised in ite_probe() after
rc_register_device() returns. If a newly registered device is opened
quickly enough, we may enable interrupts and try to use ite_dev::rdev
before it has been initialised. Move it up to the earliest point we
can, right after calling rc_allocate_device().
Reported-and-tested-by: YunQiang Su <wzssyqa@gmail.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The result of one call to a function is tested, and then at the second call
to the same function, the previous result, and not the current result, is
tested again.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression ret;
identifier f;
statement S1,S2;
@@
*ret = f(...);
if (\(ret != 0\|ret < 0\|ret == NULL\)) S1
... when any
*f(...);
if (\(ret != 0\|ret < 0\|ret == NULL\)) S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The result of one call to a function is tested, and then at the second call
to the same function, the previous result, and not the current result, is
tested again.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression ret;
identifier f;
statement S1,S2;
@@
*ret = f(...);
if (\(ret != 0\|ret < 0\|ret == NULL\)) S1
... when any
*f(...);
if (\(ret != 0\|ret < 0\|ret == NULL\)) S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is no need to call the image quality adjustment functions in sd_start.
The gspca main driver calls v4l2_ctrl_handler_setup in gspca_init_transfer,
which already applies all image control values.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The current white balance temperature default value is 4, which is much too small (possible values are 0-255).
Improve the picture quality by increasing the default value to 55, which is the default value used by the Windows driver.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Windows driver uses page 0 register 0xb6 for sharpness adjustment.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a regression from kernel 3.4 which has been introduced with the conversion of the gspca driver to the v4l2 control framework.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
1) We always re-create the input-urb on resume, so we must also always
destroy it on suspend to avoid leaking it
2) If we're going to do an init_transfer, then that will destroy the urb
before starting the stream (nop if there is none), and (re-)create it
once the stream is started. So there is little use in creating it, if
we're going to do an init_transfer immediately afterward
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_main: init_transfer does not do anything between calling sd_start
(which starts the workqueue) and releasing the usb_lock, so this
synchronization is a nop, remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In commit a3d6e8cc0e gspca_dev->dev is set
to NULL on disconnect, before calling stop0. The plan was to get rid of
gspca_dev->present and instead simply check for gspca_dev->dev everywhere
where we were checking for present. This should be race free since all users
of gspca_dev->dev hold the usb_lock, or so I thought.
But I was wrong, drivers which use a work-queue + synchronous bulk transfers
to get the video data don't hold the usb_lock while doing so, their stop0
callbacks stop the workqueue, so they won't be using gspca_dev->dev anymore
after the stop0 call, but they might be dereferincing it before, so we should
not set gspca_dev->dev to NULL on disconnect before calling stop0.
This also means that the workqueue functions in these drivers cannot
use gspca_dev->dev to check if they need to stop because of disconnection,
so we will need to keep gspca_dev->present around, and set that to 0 on
disconnect, before calling stop0. Unfortunately as part of the plan to remove
gspca_dev->present, these workqueues where already moved over to checking
for gspca_dev->dev instead of gspca_dev->present as part of commit
254902b01d, so this patch also reverts those
parts of that commit.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a nonnegative error return code to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
(
if@p1 (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret@p1 = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch changes some signed integers to unsigned because
they are not intended for negative values and sparse
is making noise about it.
Sparse gives eight of these errors:
drivers/media/usb/gspca/ov519.c:144:29: error: dubious one-bit signed bitfield
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
struct vb2_queue is allocated through kzalloc as part of a larger struct,
there's no need to clear it.
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This lock was being taken using two different names
(pointers) in the same function.
Both names refer to the same lock,
so this wasn't an error; but it looked very strange.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/radio/shark2.o: In function `_GLOBAL__sub_I_65535_0_usb_shark_suspend':
drivers/media/radio/radio-shark2.c:344: multiple definition of `usb_shark_suspend'
drivers/media/radio/radio-shark.o:/home/v4l/v4l/patchwork/drivers/media/radio/radio-shark.c:379: first defined here
drivers/media/radio/shark2.o: In function `usb_shark_resume':
drivers/media/radio/radio-shark2.c:349: multiple definition of `usb_shark_resume'
drivers/media/radio/radio-shark.o:/home/v4l/v4l/patchwork/drivers/media/radio/radio-shark.c:384: first defined here
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This completes my work on the Griffin radioSHARK2 driver, let me use this
opportunity to thank Hisaaki Shibata for his generous donation of a
Griffin radioSHARK2 to me, which has made this driver possible.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
freq fits easily into 32 bits until it gets shifted, so make it 32 bits,
and cast it to 64 bits before shifting.
[mchehab@redhat.com: also remove asm/div64.h header, as this is not
needed anymore]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for tuning AM (on devices with the necessary additional
hardware components), and advertise the available bands using the new
VIDIOC_ENUM_FREQ_BANDS ioctl.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
CC: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Am 14.08.2012 14:05, schrieb Manu Abraham:
>> My other device, a STB0899, always reports the set frequency. So it seems
>> driver dependent whether it reports the actually locked frequency found by
>> the zig-zag-algorithm or just the set frequency to tune to.
>
> The STV0299 blindly sets the value based on a software zigzag (due to simpler
> hardware), but this might not be accurate enough. On the other hand, the
> STB0899 internally does zig-zag in hardware for DVB-S2, and partly in
> software for DVB-S.
>
> In any event, the get_frontend callback should return the value that is read
> from the demodulator registers, rather than the cached original value that
> which was requested to be tuned.
>
> The stb0899 returns only the cached value IIRC. Maybe I will fix this soon,
> or maybe you can send a patch.
This is what I get after the patch:
Sat. Pol. Band Freq (MHz) Set Freq (MHz) Get Delta (MHz)
S19,2E H L 10744 10748,474 4,474
S19,2E H L 10773 10777,944 4,944
S19,2E H L 10832 10836,953 4,953
S19,2E H L 10861 10868,774 7,774
...
Signed-off-by: Reinhard Nißl <rnissl@gmx.de>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Compute the horizontal blanking value according to the datasheet. The
value written to the hblank and vblank registers must be equal to the
number of blank columns and rows minus one.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Provide pixel rate control calculated from external clock and horizontal
binning factor.
Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These helper functions get and set a 64-bit control's value from within
a driver. They are similar to v4l2_ctrl_[gs]_ctrl() but operate on
64-bit integer controls instead of 32-bit controls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initial version of this driver.
The full datasheets are available from the Analog Devices website:
http://ez.analog.com/docs/DOC-1741
Not all features of the receiver are supported by this driver for various
reasons. Most notably:
- No CEC support (the CEC API needs a lot more discussion)
- No HDCP repeater support (we don't use that either)
I'm sure that there are more things missing, but this driver does work
well for our hardware.
Note that I am using the register addresses instead of register names: the
datasheet containing the register descriptions is organized by register
address. Using names would make the datasheet lookup very hard. An attempt
was made to try and document what is being done when registers are used
instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Initial version of this driver.
The full datasheets are available from the Analog Devices website:
http://ez.analog.com/docs/DOC-1545
Not all features of the receiver are supported by this driver for various
reasons. Most notably:
- No CEC support (the CEC API needs a lot more discussion)
- Only port A of the four HDMI input ports is implemented (our hardware only
uses that port)
- No HDCP repeater support (we don't use that either)
And since there are some 600-odd pages of datasheet for this single device,
I'm sure that there are many more things missing, but this driver does work
well for our hardware.
Note that I am using the register addresses instead of register names: the
datasheet containing the register descriptions is organized by register
address. Using names would make the datasheet lookup very hard. An attempt
was made to try and document what is being done when registers are used
instead.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These two helper functions detect whether the analog video timings detected
by the video receiver match the VESA CVT or GTF standards.
They basically do the inverse of the CVT and GTF modeline calculations.
This patch also adds a helper function that will determine the aspect ratio
based on the provided EDID values. This aspect ratio can be given to the GTF
helper function.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the v4l_match_dv_timings function that can be used to compare two
v4l2_dv_timings structs.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Those files were left from dvb-usb-v2 development as I have made
mistake during rebase operation.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This symbol got removed by menu reorganization; just depending on
DVB_CORE is enough.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If pci_register_driver() failed, resources allocated in
ddb_class_create() are leaked. The patch fixes it
as well as it replaces -1 with correct error code
in ddb_class_create().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fixes problem with CAM, when after re-iinitialization
CAM used old pointer to structure.
Signed-off-by: Anton Nurkin <ptqa@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Let the dvb-frontend return -ENOTTY for those unimplemented IOCTLs.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Based on a patch from Sylvester Nawrocki
This fixes regression introduced with commmit cb7a01ac32,
"[media] move i2c files into drivers/media/i2c".
The linked order affect what drivers will be initialized first, when
they're built-in at Kernel. While there are macros that allow changing
the init order, like subsys_initcall(), late_initcall() & friends,
when all drivers linked belong to the same subsystem, it is easier
to change the order at the Makefile.
All I2C modules must be linked before any drivers that actually use it,
in order to ensure proper module initialization order.
Also, the core drivers should be initialized before the drivers that use
them.
This patch reorders the drivers init, in order to fulfill the above
requirements.
Reported-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQNUEyAAoJEHm+PkMAQRiGs+sH/iLtdAVcfBfUwdmGV0qDXbVE
L3gCg3IERPCSaQo8qsT3zujdLAQ2HsiMs73jbqJaBWSV16ZMqkglRKbn+QMGpqJV
bi/pf5Akrm9IL/u+427ycB8QxzyjGal8uJ6btuwXa03VROSfOsEiQbtsByFNaDv/
8oq0/DaE8mWRedlcAaeN+l8nD4Enb2jSKp0UADkBMnUr4KCbwSVQ+ITXAggqVq23
htA3Yt0oGf1JYq+k99D5k92h0I/4VwiorUgwPKhmS5DM9gVtJ4L+SigbekS/MFq+
huyzOHRWlO++OxBlgSTMuJAE1k/G2B7tGeoERY0tEL/hAWcKYTfGIXSc7X6JvM0=
=Dmsv
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc3' into staging/for_v3.7
Linux 3.6-rc3
* tag 'v3.6-rc3': (764 commits)
Linux 3.6-rc3
task_work: add a scheduling point in task_work_run()
fs: fix fs/namei.c kernel-doc warnings
eventpoll: use-after-possible-free in epoll_create1()
vfio: grab vfio_device reference *before* exposing the sucker via fd_install()
vfio: get rid of vfio_device_put()/vfio_group_get_device* races
vfio: get rid of open-coding kref_put_mutex
introduce kref_put_mutex()
vfio: don't dereference after kfree...
fbcon: fix race condition between console lock and cursor timer (v1.1)
mm: compaction: Abort async compaction if locks are contended or taking too long
mm: have order > 0 compaction start near a pageblock with free pages
rapidio/tsi721: fix unused variable compiler warning
rapidio/tsi721: fix inbound doorbell interrupt handling
drivers/rtc/rtc-rs5c348.c: fix hour decoding in 12-hour mode
mm: correct page->pfmemalloc to fix deactivate_slab regression
drivers/rtc/rtc-pcf2123.c: initialize dynamic sysfs attributes
mm/compaction.c: fix deferring compaction mistake
drivers/misc/sgi-xp/xpc_uv.c: SGI XPC fails to load when cpu 0 is out of IRQ resources
string: do not export memweight() to userspace
...
Pull media fixes from Mauro Carvalho Chehab:
"For bug fixes, at soc_camera, si470x, uvcvideo, iguanaworks IR driver,
radio_shark Kbuild fixes, and at the V4L2 core (radio fixes)."
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] media: soc_camera: don't clear pix->sizeimage in JPEG mode
[media] media: mx2_camera: Fix clock handling for i.MX27
[media] video: mx2_camera: Use clk_prepare_enable/clk_disable_unprepare
[media] video: mx1_camera: Use clk_prepare_enable/clk_disable_unprepare
[media] media: mx3_camera: buf_init() add buffer state check
[media] radio-shark2: Only compile led support when CONFIG_LED_CLASS is set
[media] radio-shark: Only compile led support when CONFIG_LED_CLASS is set
[media] radio-shark*: Call cancel_work_sync from disconnect rather then release
[media] radio-shark*: Remove work-around for dangling pointer in usb intfdata
[media] Add USB dependency for IguanaWorks USB IR Transceiver
[media] Add missing logging for rangelow/high of hwseek
[media] VIDIOC_ENUM_FREQ_BANDS fix
[media] mem2mem_testdev: fix querycap regression
[media] si470x: v4l2-compliance fixes
[media] DocBook: Remove a spurious character
[media] uvcvideo: Reset the bytesused field when recycling an erroneous buffer
drivers/built-in.o: In function `imx074_s_power':
imx074.c:(.text+0x1de93d0): undefined reference to `soc_camera_power_on'
imx074.c:(.text+0x1de93f3): undefined reference to `soc_camera_power_off'
drivers/built-in.o: In function `mt9m001_s_mbus_config':
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As Reported by Randy:
> drivers/built-in.o: In function `fops_open':
> saa7164-encoder.c:(.text+0x68ed6f): undefined reference to `video_devdata'
> drivers/built-in.o: In function `fill_queryctrl.clone.4':
> saa7164-encoder.c:(.text+0x68f657): undefined reference to `v4l2_ctrl_query_fill'
> saa7164-encoder.c:(.text+0x68f6a9): undefined reference to `v4l2_ctrl_query_fill'
> saa7164-encoder.c:(.text+0x68f6e0): undefined reference to `v4l2_ctrl_query_fill'
> saa7164-encoder.c:(.text+0x68f71a): undefined reference to `v4l2_ctrl_query_fill'
> saa7164-encoder.c:(.text+0x68f73a): undefined reference to `v4l2_ctrl_query_fill'
> drivers/built-in.o:saa7164-encoder.c:(.text+0x68f757): more undefined references to `v4l2_ctrl_query_fill' follow
> drivers/built-in.o: In function `saa7164_encoder_register':
> (.text+0x68fff7): undefined reference to `video_device_alloc'
> drivers/built-in.o: In function `saa7164_encoder_register':
> (.text+0x690073): undefined reference to `video_device_release'
> drivers/built-in.o: In function `saa7164_encoder_register':
> (.text+0x6900a1): undefined reference to `__video_register_device'
> drivers/built-in.o: In function `saa7164_encoder_unregister':
> (.text+0x690243): undefined reference to `video_unregister_device'
> drivers/built-in.o: In function `saa7164_encoder_unregister':
> (.text+0x690269): undefined reference to `video_device_release'
> drivers/built-in.o: In function `fops_open':
> saa7164-vbi.c:(.text+0x69125f): undefined reference to `video_devdata'
> drivers/built-in.o: In function `fill_queryctrl.clone.4':
> saa7164-vbi.c:(.text+0x6919b4): undefined reference to `v4l2_ctrl_query_fill'
> saa7164-vbi.c:(.text+0x6919ee): undefined reference to `v4l2_ctrl_query_fill'
> saa7164-vbi.c:(.text+0x691a23): undefined reference to `v4l2_ctrl_query_fill'
> saa7164-vbi.c:(.text+0x691a47): undefined reference to `v4l2_ctrl_query_fill'
> saa7164-vbi.c:(.text+0x691a6a): undefined reference to `v4l2_ctrl_query_fill'
> drivers/built-in.o:saa7164-vbi.c:(.text+0x691a87): more undefined references to `v4l2_ctrl_query_fill' follow
> drivers/built-in.o: In function `saa7164_vbi_register':
> (.text+0x69220e): undefined reference to `video_device_alloc'
> drivers/built-in.o: In function `saa7164_vbi_register':
> (.text+0x69228a): undefined reference to `video_device_release'
> drivers/built-in.o: In function `saa7164_vbi_register':
> (.text+0x6922bb): undefined reference to `__video_register_device'
> drivers/built-in.o: In function `saa7164_vbi_unregister':
> (.text+0x6923de): undefined reference to `video_unregister_device'
> drivers/built-in.o: In function `saa7164_vbi_unregister':
> (.text+0x6923f9): undefined reference to `video_device_release'
> drivers/built-in.o:(.rodata+0xb1054): undefined reference to `video_ioctl2'
> drivers/built-in.o:(.rodata+0xb17d4): undefined reference to `video_ioctl2'
That's due to the lack of an explicit Kconfig dependency for the V4L2 core.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
As reported by Randy:
> flexcop-pci.c:(.text+0x19af63): undefined reference to `flexcop_device_exit'
> flexcop-pci.c:(.text+0x19af77): undefined reference to `flexcop_device_kfree'
> flexcop-pci.c:(.text+0x19b10f): undefined reference to `flexcop_pass_dmx_packets'
> flexcop-pci.c:(.text+0x19b182): undefined reference to `flexcop_pass_dmx_data'
> flexcop-pci.c:(.text+0x19b1ae): undefined reference to `flexcop_pass_dmx_data'
> flexcop-pci.c:(.text+0x19b1f8): undefined reference to `flexcop_device_kmalloc'
> flexcop-pci.c:(.text+0x19b256): undefined reference to `flexcop_i2c_request'
> flexcop-pci.c:(.text+0x19b261): undefined reference to `flexcop_eeprom_check_mac_addr'
> flexcop-pci.c:(.text+0x19b2c6): undefined reference to `flexcop_device_initialize'
> flexcop-pci.c:(.text+0x19b332): undefined reference to `flexcop_sram_set_dest'
> flexcop-pci.c:(.text+0x19b348): undefined reference to `flexcop_sram_set_dest'
> flexcop-pci.c:(.text+0x19b3f8): undefined reference to `flexcop_device_exit'
> flexcop-pci.c:(.text+0x19b408): undefined reference to `flexcop_device_kfree'
> flexcop-pci.c:(.text+0x19b4a2): undefined reference to `flexcop_pid_feed_control'
> flexcop-pci.c:(.text+0x19b4d7): undefined reference to `flexcop_pid_feed_control'
>
> since it is possible to enable DVB_B2C2_FLEXCOP_PCI
> when CONFIG_I2C is not enabled, but then DVB_B2C2_FLEXCOP
> is not enabled because I2C is not enabled.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A trivial fix so that vino can find the saa7191.h header.
[mchehab@redhat.com: Fix merge conflict]
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of having 3 options to allow customizing the media
sub-drivers (tuners, I2C drivers, frontends), merge all of
them into just one.
That simplifies the life for users, as they can just keep
this untouched.
Life for developers is also simpler, as there's now just
one Kconfig item to remember, for the ancillary sub-drivers
providing supports for chips that could change from one
board design to another.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- get rid of ridden V4L2_COMMON symbol
This symbol is not needed anymore; it can be folded with V4L2
one, simplifying the Kconfig a little bit;
- Comment why some Kconfig items are needed;
- Remove if test for MEDIA_CAMERA_SUPPORT, replacing it by
depends on.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Vivi is not that important to appear at the main menu, so move it
to its own submenu. Also, the mem2mem test device driver is
similar to vivi. So, put both at the same menu.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
That helps to better organize the soc_camera items.
While here, cleanup Makefiles, removing uneeded include dirs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
make[4]: *** No rule to make target `drivers/media/platform/sh_mobile_csi2.c',
needed by `drivers/media/platform/sh_mobile_csi2.o'. Stop.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
CC: Michael Krufky <mkrufky@linuxtv.org>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Doron Cohen <doronc@siano-ms.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On a few places, := were using instead of +=, causing drivers to
not compile.
While here, standardize the usage of += on all cases where multiple
lines are needed, and for obj-y/obj-m targets, and := when just one
line is needed, on <module>-obj rules.
Reported-by: Hans Verkuil <hverkuil@xs4all.nl>
Identified-by: Antti Polosaari <crope@iki.fi>
Tested-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Netup cards revision 1 are not manufactured anymore.
So, rev. 4 should be default.
Signed-off-by: Anton Nurkin <ptqa@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In JPEG mode, the size of image is variable due to different JPEG compression
rate. We only can get the pix->sizeimage from the user.
If we clear pix->sizeimage in soc_camera_try_fmt() then we will get it from:
ret = soc_mbus_image_size(xlate->host_fmt, pix->bytesperline,
pix->height);
if (ret < 0)
return ret;
pix->sizeimage = max_t(u32, pix->sizeimage, ret);
In general, this sizeimage will be larger than the actul JPEG image size.
But vb2 will check the buffer and size of image in __qbuf_userptr():
/* Check if the provided plane buffer is large enough */
if (planes[plane].length < q->plane_sizes[plane])
So we shouldn't clear the pix->sizeimage and also shouldn't re-calculate
the pix->sizeimage in soc_mbus_image_size() in JPEG mode
We also shouldn't re-calculate pix->bytesperline:
ret = soc_mbus_bytes_per_line(pix->width, xlate->host_fmt);
if (ret < 0)
return ret;
pix->bytesperline = max_t(u32, pix->bytesperline, ret);
pix->bytesperline also should be set by the user or by the driver's
try_fmt() implementation.
Change-Id: I700690a2287346127a624b5260922eaa5427a596
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch contains code change only to use the present macro-
MX3_CAMERA_DATAWIDTH_MASK to check valid camera platform data
bus width instead of enumerating every possible data bus width.
Signed-off-by: Liu Ying <Ying.Liu@freescale.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Driver for mt9v022 camera sensor is fully compatible for mt9v024 camera sensor
with the exception of several registers which have been changed addresses.
mt9v024 also has improved and additional features, but they are currently not in use.
Signed-off-by: Alex Gershgorin <alexg@meprolight.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On i.MX27 two clocks are required: emma-ipg and emma-ahb. The ahb clock
has to be requested using both a device and a connection ID.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
[g.liakhovetski@gmx.de: rebase to the current media tree]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch checks the state of the buffer when calling .buf_init() method.
This is needed for the USERPTR buffer type, because in that case
.buf_init() is called every time a buffer is queued, and not only once
during the preparation stage, like in the MMAP case. Without this check
buffers get initialised repeatedly, which also leads to the allocation
of new DMA descriptors, of which there is only a final relatively small
number available. Both MMAP and USERPTR methods were successfully tested.
Signed-off-by: Alex Gershgorin <alexg@meprolight.com>
[g.liakhovetski@gmx.de: remove mx3_camera_buffer::state completely]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In JPEG mode, the size of image is variable due to different JPEG compression
rate. We only can get the pix->sizeimage from the user.
If we clear pix->sizeimage in soc_camera_try_fmt() then we will get it from:
ret = soc_mbus_image_size(xlate->host_fmt, pix->bytesperline,
pix->height);
if (ret < 0)
return ret;
pix->sizeimage = max_t(u32, pix->sizeimage, ret);
In general, this sizeimage will be larger than the actul JPEG image size.
But vb2 will check the buffer and size of image in __qbuf_userptr():
/* Check if the provided plane buffer is large enough */
if (planes[plane].length < q->plane_sizes[plane])
So we shouldn't clear the pix->sizeimage and also shouldn't re-calculate
the pix->sizeimage in soc_mbus_image_size() in JPEG mode
We also shouldn't re-calculate pix->bytesperline:
ret = soc_mbus_bytes_per_line(pix->width, xlate->host_fmt);
if (ret < 0)
return ret;
pix->bytesperline = max_t(u32, pix->bytesperline, ret);
pix->bytesperline also should be set by the user or by the driver's
try_fmt() implementation.
Change-Id: I700690a2287346127a624b5260922eaa5427a596
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On i.MX27 two clocks are required: emma-ipg and emma-ahb. The ahb clock
has to be requested using both a device and a connection ID.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
[g.liakhovetski@gmx.de: rebase to the current media tree]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch checks the state of the buffer when calling .buf_init() method.
This is needed for the USERPTR buffer type, because in that case
.buf_init() is called every time a buffer is queued, and not only once
during the preparation stage, like in the MMAP case. Without this check
buffers get initialised repeatedly, which also leads to the allocation
of new DMA descriptors, of which there is only a final relatively small
number available. Both MMAP and USERPTR methods were successfully tested.
Signed-off-by: Alex Gershgorin <alexg@meprolight.com>
[g.liakhovetski@gmx.de: remove mx3_camera_buffer::state completely]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add .reset_resume() support.
Also some other small changes for suspend / resume.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move initial suspend / resume support from dvb_usb_v2 to dvb_frontend
as it is dvb general feature that could be used all dvb devices.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Put device full sleep on suspend, wake-up it on resume and acquire
retune in order to return same television channel.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The commit 98d7bbb9 changed *of_device_id.data to const
which introduced warnings in various places that have mostly
been fixed. This patch fixes one such warning by introducing
two const qualifiers.
GCC warning:
drivers/media/platform/coda.c:1785:16: warning:
assignment discards ‘const’ qualifier
from pointer target type [enabled by default]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
debug_dump macro was defined twice when CONFIG_DVB_USB_DEBUG was
not set. Move debug_dump macro to correct place.
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the NULL test is necessary, the initialization involving a dereference of
the tested value should be moved after the NULL test.
The sematic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
devm_regulator_get() is a device managed function and makes the exit code
a bit simpler and cleaner.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using devm_kzalloc simplifies the code and ensures that the use of
devm_request_irq is safe. When kzalloc and kfree were used, the interrupt
could be triggered after the handler's data argument had been freed.
This also introduces some missing initializations of the return variable
ret, and uses devm_request_and_ioremap instead of the combination of
devm_request_mem_region and devm_ioremap.
The problem of a free after a devm_request_irq was found using the
following semantic match (http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
expression e1,e2,x,a,b,c,d;
identifier free;
position p1,p2;
@@
devm_request_irq@p1(e1,e2,...,x)
... when any
when != e2 = a
when != x = b
if (...) {
... when != e2 = c
when != x = d
free@p2(...,x,...);
...
return ...;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
"card" is a valid pointer here because we checked snd_card_create() for
error returns. Checking after a dereference makes the static checkers
complain.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are some unlocks missing on error.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We recently added locking to this function, but there was an error path
which accidentally returned holding a lock. Also we returned zero on
failure on some paths instead of the error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We need to move the unlock before the kfree(dev);
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This code looks suspicious, but it turns out that "nv" is an array of u8
so sizeof() is the same as ARRAY_SIZE(). Using ARRAY_SIZE() is more
readable though.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add .get_selection() and .set_selection() soc-camera host driver
operations. Additionally check, that the user is not trying to change the
output sizes during a running capture.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add explicit conversions from UYVY and YUYV to YUYV so that
csicr1 configuration can be set properly for each format.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sensor starts streaming video as soon as it gets powered or is
reset. Disable the output in the reset function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Conversion from i2c_client to ov772x_priv is only needed in a single
location, while conversion from v4l2_subdev to ov772x_priv is needed in
several locations. Perform the former manually, and use to_ov772x for
the later.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the requested format isn't supported, return a fixed default format
instead of the current format.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The format and window size are only initialized during the first g_fmt
call. This leaves the device in an inconsistent state after
initialization, which will cause problems when implementing pad
operations. Move the format and window size initialization to probe
time.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The control handler isn't freed if its initialization fails. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several client drivers access the hardware at probe time, for instance
to read the probe chip ID. Such chips need to be powered up when being
probed.
soc-camera handles this by powering chips up in the soc-camera probe
implementation. However, this will break with non soc-camera hosts that
don't perform the same operations.
Fix the problem by pushing the power up/down from the soc-camera core
down to individual drivers on a needs basis.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of forcing all soc-camera drivers to go through the mid-layer to
handle power management, create soc_camera_power_[on|off]() functions
that can be called from the subdev .s_power() operation to manage
regulators and platform-specific power handling. This allows non
soc-camera hosts to use soc-camera-aware clients.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[g.liakhovetski@gmx.de: fix compile breakage]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Powering off a device is a "best effort" task: failure to execute one of
the steps should not prevent the next steps to be executed. For
instance, an I2C communication error when putting the chip in stand-by
mode should not prevent the more agressive next step of turning the
chip's power supply off.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The .s_power() call only covers the .g_mbus_fmt() operation call.
Several clients required to be powered on to retrieve the current mbus
format but have now been fixed. The .s_power() call is thus not needed
anymore and can be removed.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The remaining drivers are mostly platform drivers. Name the
dir to reflect it.
It makes sense to latter break it into a few other dirs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Reorganize the API core changes for them to appear closer to
the items that enable them, and not at the drivers part of
the menu.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We should keep just the I2C drivers under drivers/media/video, and
then rename it to drivers/media/i2c.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename all PCI drivers with their own directory under
drivers/media/video into drivers/media/pci and update the
building system.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename all USB drivers with their own directory under
drivers/media/video into drivers/media/usb and update the
building system.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix a one-character typo at the makefile.
drivers/built-in.o: In function `flexcop_pci_remove':
flexcop-pci.c:(.text+0x20d1a28): undefined reference to `flexcop_dma_free'
flexcop-pci.c:(.text+0x20d1a3e): undefined reference to `flexcop_dma_free'
drivers/built-in.o: In function `flexcop_pci_stream_control':
flexcop-pci.c:(.text+0x20d2396): undefined reference to `flexcop_dma_config'
flexcop-pci.c:(.text+0x20d23b3): undefined reference to `flexcop_dma_config'
flexcop-pci.c:(.text+0x20d23cf): undefined reference to `flexcop_dma_config_timer'
flexcop-pci.c:(.text+0x20d23f5): undefined reference to `flexcop_dma_xfer_control'
flexcop-pci.c:(.text+0x20d244c): undefined reference to `flexcop_dma_control_timer_irq'
flexcop-pci.c:(.text+0x20d24b0): undefined reference to `flexcop_dma_control_timer_irq'
flexcop-pci.c:(.text+0x20d2507): undefined reference to `flexcop_dma_xfer_control'
drivers/built-in.o: In function `flexcop_pci_probe':
flexcop-pci.c:(.text+0x20d28d2): undefined reference to `flexcop_dma_allocate'
flexcop-pci.c:(.text+0x20d2907): undefined reference to `flexcop_dma_allocate'
flexcop-pci.c:(.text+0x20d2923): undefined reference to `flexcop_dma_free'
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes section mismatch warnings for
davinci video drivers.
[mchehab@redhat.com: applied it as a fixup over the previous (and wrong) changeset c6afbf2]
Signed-off-by: Lad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: Manjunath Hadli <manjunath.hadli@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
siano is, in fact, 2 drivers: one for MMC and one for USB, plus
a common bus-independent code. Break it accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In order to better organize the directory tree, move the
saa7146 common driver to its own directory.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move the tuners one level up, as the "common" directory will be used
by drivers that are shared between more than one driver.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
b2c2 is, in fact, 2 drivers: one for PCI and one for USB, plus
a common bus-independent code. Break it accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Raise the DVB frontends one level up, as the intention is to remove
the drivers/media/dvb directory.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
just like the V4L2 core, move the DVB core to drivers/media, as the
intention is to get rid of both "video" and "dvb" directories.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently, the v4l2 core is mixed together with other non-core drivers.
Move them into a separate directory.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Functional changes
PID filter is default to off and controlled from dvb-usb-v2
Driver now supports suspend and resume changes in dvb-usb-v2
USB bus repeater functions have been removed.
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
i.MX25 support is known to have been broken for almost a year.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
devm_kzalloc() eliminates the need to free explicitly thereby
making the code a bit simpler.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The correct place to put i2c_gate_ctrl is before calling tda18271_attach,
because the driver tda18271 will use it to enable or disable the i2c-bus
from the demodulator to the tuner.
And thus eliminate the error message: "Unknown device (255) detected
@ 1-00c0, device not supported" in the driver tda18271.
In the device kworld_sbtvd (hybrid analog and digital TV) the control
of the i2c-bus to tuner is done in the analog demodulator and not in
the digital demodulator.
Signed-off-by: Manoel Pinheiro <pinusdtv@hotmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The lirc TX functionality expects the process which writes (TX) data to
the lirc dev to sleep until the actual data has been transmitted by the
hardware.
Since the same timeout calculation is duplicated in more than one driver
(and would have to be duplicated in even more drivers as they gain TX
support), it makes sense to move this timeout calculation to the lirc
layer instead.
At the same time, centralize some of the sanity checks.
Signed-off-by: David Härdeman <david@hardeman.nu>
Cc: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On Mon, 2012-08-13 at 19:58 +0300, Dan Carpenter wrote:
> Hello Mauro Carvalho Chehab,
>
> The patch db6651a9ebb3: "[media] lmedm04: fix build" from Aug 12,
> 2012, leads to the following warning:
> drivers/media/dvb/dvb-usb-v2/lmedm04.c:769 lme2510_download_firmware()
> error: usb_control_msg() 'data' too small (128 vs 265)
>
> 737 data = kzalloc(128, GFP_KERNEL);
> ^^^
> data is 128 bytes.
Control isn't used, so remove it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When the TEI bit is raised, we should not trust any of the contents of
the packet in question, including but not limited to its PID number.
Considering that we don't trust the PID number of this packet, we should
not proceed to check the packet counter (if dvb_demux_tscheck is set).
We should expect to see at least one discontinuity after a bad packet is
received, so any time a TEI is detected, a following TS packet counter
mismatch is to be expected.
There is no real reason to ever allow bad packets to pass through the
kernel demux, other than for purposes of attempting error correction via
software or statistical information.
However, since we have always passed these bad packets though the demux,
we should not change this default behavior.
Without altering module options, this patch merely prevents the
TS packet counter check on packets containing a raised TEI.
If module option dvb_demux_feed_err_pkts is set to 0, the kernel demux
will drop these error packets entirely, preventing any possibility of
corruption caused by userspace programs that are expecting valid data.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch fixes the following sparse warnings
by removing use of duplicate const.
drivers/media/video/cx88/cx88.h:152:40:
warning: duplicate const
drivers/media/video/cx88/cx88-core.c:256:33:
warning: duplicate const
drivers/media/video/cx88/cx88-alsa.c:769:41:
warning: duplicate const
As commented by Jonathan Nieder:
These double "const" were introduced in v2.6.37-rc1~64^2~464 (V4L/DVB:
drivers/media: Make static data tables and strings const, 2010-08-25).
The address of an array is already immutable by definition, so for
what it's worth, with or without a clarified commit message,
[mchehab@redhat.com: Tested with "gcc -s" (version 4.7.0):
the produced asm is indeed equal before and after this patch]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Acked-by: Jonathan Nieder <jrnieder@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is the driver for the IR transmitter diode found on the Nokia
N900 (also known as RX51) device. The driver is mostly the same as
found in the original 2.6.28 based kernel that comes with the device.
The following modifications have been made compared to the original
driver version:
- Adopt to the changes that has happen in the kernel during the past
five years, such as the change in the include paths
- The OMAP DM-timers require much more care nowadays. The timers need
to be enabled and disabled or otherwise many actions fail. Timers
must not be freed without first stopping them or otherwise the timer
cannot be requested again.
The code has been tested with sending IR codes with N900 device
running Debian userland. The device receiving the codes was Anysee
DVB-C USB receiver.
Signed-off-by: Timo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This callback were meant to allow overriding a FE callback, before its
call, but it is not really needed, as the callback can be intercepted
after tuner attachment.
Worse than that, only DVBv3 calls are intercepted this way, so a DVBv5
application will produce different effects than a DVBv3 one.
So, get rid of it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
In two cases, the original memory allocation function was kmalloc, which
has been changed to a zeroing allocation to benefit from the devm function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently write() will return 0 if an IR device does not support sending.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This simplies the code and resolves a possible race condition between
ir_raw_decode_timer_end() and saa7134_raw_decode_irq().
If the interrupt handler is called after ir_raw_decode_timer_end()
calls ir_raw_event_handle() but before clearing ir->active, then the
timer won't be rearmed.
Compile tested only.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The TechnoTrend USB IR Receiver sends 125 ISO URBs per second, even when
there is no IR activity. Reduce the number of wake ups from the other
drivers too.
This saves about 0.25ms/s on a 2.4GHz Core 2 according to powertop.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver adds support for TechnoTrend USB IR Receiver. It is a complete
rewrite of the staging/media/lirc/lirc_ttusbir driver. It adds more
accurate sample reporting and led control.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The Pioneer CU-700 remote causes receiver overflows if you hold down any
button. The remote does not send NEC IR repeats, it repeats the entire
NEC code after 20ms.
The iguanair hardware advertises an interval of 10 which just not enough;
with 100 URBs per second and at most 7 edges per URB, we handle at most
700 edges per second. The remote generates about 900.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
With the timeout supplied the interface can go idle. The keymap is
the same one as other drivers which do not come with a remote.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Firmware versions lower than 0x0205 use a different interface which is not
supported. Also report the firmware version in the standard format.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rather than using usb_interrupt_msg() to receive responses, reuse the
urb callback we already have in place.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Move rtl2831u LED from streaming control to power control. It
changes LED behavior slightly but who cares :)
After that same streaming control can be used for both rtl2831u
and rtl2832u.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The camera requires the PROBE_MINMAX quirk. Add a corresponding entry in
the device IDs list.
Reported-by: Stefan Muenzel <stefanmuenzel@googlemail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The SPCAM SP620U camera uses the alternate "Y8 " GUID for the 8-bit
greyscale format, and supports a 12-bit greyscale format. Add support
for those in the driver, as well as for 10-bit greyscale formats.
Signed-off-by: Stefan Muenzel <stefanmuenzel@googlemail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Compute the maximum number of bytes per interval using the burst and
multiplier values for super speed endpoints.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Support for yet another SAA7146-based budget card (very similar to TT
S2-1600, but use LNBH23 instead ISL6423).
Signed-off-by: Evgeny Plehov <EvgenyPlehov@ukr.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This driver adds support for stk1160 usb bridge as used in some
video/audio usb capture devices.
It is a complete rewrite of staging/media/easycap driver and
it's meant as a replacement.
As stk1160 allows communication with an ac97 codec chip, this
driver allows to register a control-only sound card to allow the user
to access ac97 controls.
Two devices have been used for testing:
* 1-cvbs video and 1-audio ac97 input,
* 4-cvbs inputs
Both of these devices reports with the same id [05e1:0408],
so the driver tries to support a superset of the capabilities.
By using keep_buffers module parameter it's possible to prevent
the driver from releasing urb buffers when streaming is stopped.
The usage of this parameter can avoid memory fragmentation that may
cause the driver to stop working on low memory systems.
A similar mechanism is implemented in em28xx driver (see commit 86d38d).
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This removes the need for shark_led_work to take the v4l2 lock.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Recent kernels properly clear the usb intfdata pointer when another
driver fails to bind (in the radio-shark* case the usbhid driver would try
to bind first.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
qt1010_init_meas2() returns zero on success and negative error codes on
failure so the return type should be int instead of u8.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Antti Palosaari