Simpler, more consistent, with negligible cost in non-critical paths.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Suggested-by: Michał Mirosław <mirqus@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
- atomic bit operations are globally visible
- pending status is always cleared before execution
- scheduled works are either idempotent or only required to happen once
after a series of originating events, say link events for instance
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Suggested-by: Michał Mirosław <mirqus@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
With infinite gratitude to Eric Dumazet for allowing me to identify
the error.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
The reorganization of the driver layout in drivers/net
left behind some stale paths in comments and in Kconfig
help text. Bring them up to date. No actual change to
any code takes place here.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The irq handler was a mess.
See 7ab87ff4c7 ("via-rhine: move work from
irq handler to softirq and beyond") for similar changes. One can notice:
- all non-napi tasks are explicitely scheduled trough a single work queue.
- hiding software tx queue start behind the rtl_hw_start method is mildly
natural. Move it in the caller where needed.
- as can be seen from the heavy use of bh disabling locks, the driver is
not safe for irq context messages with netconsole. It is still quite
usable for general messaging though. Tested ok with concurrent registers
dump (ethtool -d) + background traffic + "echo t > /proc/sysrq-trigger".
Tested with old PCI chipset, PCIe 8168 and 810x:
- XID 0c900800 RTL8168evl/8111evl
- XID 18000000 RTL8168b/8111b
- XID 98000000 RTL8169sc/8110sc
- XID 083000c0 RTL8168d/8111d
- XID 081000c0 RTL8168d/8111d
- XID 00b00000 RTL8105e
- XID 04a00000 RTL8102e
As a side note, the comments in f11a377b3f
("r8169: avoid losing MSI interrupts") does not seem completely clear: if
I hack the driver further to stop acking the irq link event bit, MSI
interrupts keep being delivered (RTL8168b/8111b, XID 18000000).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Though motivated by the move of the driver to a single work queue of
sequential events and removal of hard irq processing, it looks safe as
a standalone change.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
I see no good reason to keep both rtl8169_reinit_task and rtl8169_reset_task:
- rtl8169_reinit_task adds a software failure point which does relate to
any hardware state
- they handle hardware the same. Remember that rtl8169_reinit_task was
introduced in the 8169 only era to handle PCI errors way before the 8168
asked for pll and firmware ops and compare :
rtl8169_reinit_task | rtl8169_reset_task
----------------------------+--------------------------
rtl8169_wait_for_quiescence | rtl8169_hw_reset
rtl8169_update_counters | rtl8169_wait_for_quiescence
rtl8169_hw_reset | rtl_hw_start
rtl8169_rx_missed | rtl8169_check_link_status
rtl_pll_power_down |
rtl_request_firmware |
rtl8169_init_phy |
rtl_pll_power_up |
rtl_hw_start |
rtl8169_check_link_status |
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
The driver uses __napi_complete and napi_gro_receive. Without it, the
driver hits the BUG_ON(n->gro_list) assertion hard in __napi_complete.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Marin Glibic <zhilla2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rx mode should be reset after resming, so unconditionally updating rx
mode rather than conditionally updating based on the value we
remembered, otherwise unexpected value may be used by the nic after
resuming.
btw. I find and test this when debugging guest hibernation in qemu, as
I did not have a 8139cp card in hand, this patch is untested in a
physical 8139cp card, plase review it carefully.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
delay_eeprom() use long read for Cfg9346 register(offset 0x50) which may read
into the area of reserved register(offset 0x53). Use byte read instead.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bluetooth/l2cap_core.c
Just two overlapping changes, one added an initialization of
a local variable, and another change added a new local variable.
Signed-off-by: David S. Miller <davem@davemloft.net>
The MSIEnable bit is only available for the 8169.
Avoid Config2 writes for the post-8169 8168 and 810x.
Reported-by: Su Kang Yin <cantona@cantona.net>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 92fc43b415, rtl8169_tx_timeout ends up
resetting Rx and Tx indexes and thus racing with the NAPI handler via
-> rtl8169_hw_reset
-> rtl_hw_reset
-> rtl8169_init_ring_indexes
What about returning to the original state ?
rtl_hw_reset is only used by rtl8169_hw_reset and rtl8169_init_one.
The latter does not need rtl8169_init_ring_indexes because the indexes
still contain their original values from the newly allocated network
device private data area (i.e. 0).
rtl8169_hw_reset is used by:
1. rtl8169_down
Helper for rtl8169_close. rtl8169_open explicitely inits the indexes
anyway.
2. rtl8169_pcierr_interrupt
Indexes are set by rtl8169_reinit_task.
3. rtl8169_interrupt
rtl8169_hw_reset is needed when the device goes down. See 1.
4. rtl_shutdown
System shutdown handler. Indexes are irrelevant.
5. rtl8169_reset_task
Indexes must be set before rtl_hw_start is called.
6. rtl8169_tx_timeout
Indexes should not be set. This is the job of rtl8169_reset_task anyway.
The removal of rtl8169_hw_reset in rtl8169_tx_timeout and its move in
rtl8169_reset_task do not change the analysis.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Realtek has specified that the post 8168c gigabit chips and the post
8105e fast ethernet chips recover automatically from a Rx FIFO overflow.
The driver does not need to clear the RxFIFOOver bit of IntrStatus and
it should rather avoid messing it.
The implementation deserves some explanation:
1. events outside of the intr_event bit mask are now ignored. It enforces
a no-processing policy for the events that either should not be there
or should be ignored.
2. RxFIFOOver was already ignored in rtl_cfg_infos[RTL_CFG_1] for the
whole 8168 line of chips with two exceptions:
- RTL_GIGA_MAC_VER_22 since b5ba6d12bd
("use RxFIFO overflow workaround for 8168c chipset.").
This one should now be correctly handled.
- RTL_GIGA_MAC_VER_11 (8168b) which requires a different Rx FIFO
overflow processing.
Though it does not conform to Realtek suggestion above, the updated
driver includes no change for RTL_GIGA_MAC_VER_12 and RTL_GIGA_MAC_VER_17.
Both are 8168b. RTL_GIGA_MAC_VER_12 is common and a bit old so I'd rather
wait for experimental evidence that the change suggested by Realtek really
helps or does not hurt in unexpected ways.
Removed case statements in rtl8169_interrupt are only 8168 relevant.
3. RxFIFOOver is masked for post 8105e 810x chips, namely the sole 8105e
(RTL_GIGA_MAC_VER_30) itself.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: hayeswang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Round-up some wayward "N/A" fw_version dust bunnies as part of that
clean-up.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce the number of #defines, use the normal #define from if_ether.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Per the mention made by Ben Hutchings that strlcpy is now the preferred
string copy routine for a .get_drvinfo routine, do a bit of floor
sweeping and convert some of the as-yet unconverted ethernet drivers to
it.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link down would occur when reseting PHY. And it would take about 2 ~ 5 seconds
from link down to link up. If the delay of pm_schedule_suspend is not long enough,
the device would enter runtime_suspend before link up. After link up, the device
would wake up and reset PHY again. Then, you would find the driver keep in a loop
of runtime_suspend and rumtime_resume.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While the SC92031 could be found on fake "Realtek" NICs, it has no
relationship to Realtek, and is actually from Silan.
Create a new subdirectory for silan and move sc92031 there.
Signed-off-by: Cesar Eduardo Barros <cesarb@cesarb.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
To ease skb->truesize sanitization, its better to be able to localize
all references to skb frags size.
Define accessors : skb_frag_size() to fetch frag size, and
skb_frag_size_{set|add|sub}() to manipulate it.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for reporting ring sizes via ethtool -g to the 8139cp driver.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- fix features : jumbo frames and checksumming can not be used at the
same time.
- introduce hw_jumbo_{enable / disable} helpers. Their content has been
creatively extracted from Realtek's own drivers. As an illustration,
it would be nice to know how/if the MaxTxPacketSize register operates
when the device can work with a 9k jumbo frame as its documentation
(8168c) can not be applied beyond ~7k.
- rtl_tx_performance_tweak is moved forward. No change.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
8168d and above allow jumbo frames beyond 8k. Bump the received
packet length check before enabling jumbo frames on these chipsets.
Frame length indication covers bits 0..13 of the first Rx descriptor
32 bits for the 8169 and 8168. I only have authoritative documentation
for the allowed use of the extra (13) bit with the 8169 and 8168c.
Realtek's drivers use the same mask for the 816x and the fast ethernet
only 810x.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
For RTL8111EVL, the register of MaxTxPacketSize doesn't acctually
limit the tx size. It influnces the feature of early tx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
MII Kconfig option is apart of the core networking drivers and
by default NET_CORE is enabled so drivers selecting MII will
have MII enabled as well. It was found using the randconfig
option during testing, MII would be selected but NET_CORE
could be disabled. This caused a dependency error.
Resolved the dependency by selecting NET_CORE when MII is
selected.
Reported-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on finds for Stephen Rothwell, where current defconfig's
enable a ethernet driver and it is not compiled due to the newly
added NET_VENDOR_* component of Kconfig.
This patch enables all the "new" Kconfig options so that current
defconfig's will continue to compile the expected drivers. In
addition, by enabling all the new Kconfig options does not add
any un-expected options.
CC: Stephen Rothwll <sfc@canb.auug.org.au>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move the Realtek drivers into drivers/net/ethernet/realtek/ and make
the necessary Kconfig and Makefile changes.
CC: Realtek linux nic maintainers <nic_swsd@realtek.com>
CC: Francois Romieu <romieu@fr.zoreil.com>
CC: Jeff Garzik <jgarzik@pobox.com>
CC: Donald Becker <becker@scyld.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Francois Romieu