Commit 2abb0d5268 ("PM / devfreq: Lock devfreq in trans_stat_show")
revealed a missing locking while calling devfreq_update_status() function
during suspend/resume cycle.
Code analysis revealed that devfreq_set_target() function was called
without needed locks held for setting device specific suspend_freq if such
has been defined. This patch fixes that by adding the needed locking, what
fixes following kernel warning on Exynos4412-based OdroidU3 board during
system suspend:
PM: suspend entry (deep)
Filesystems sync: 0.002 seconds
Freezing user space processes ... (elapsed 0.001 seconds) done.
OOM killer disabled.
Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
------------[ cut here ]------------
WARNING: CPU: 2 PID: 1385 at drivers/devfreq/devfreq.c:204 devfreq_update_status+0xc0/0x188
Modules linked in:
CPU: 2 PID: 1385 Comm: rtcwake Not tainted 5.4.0-rc6-next-20191111 #6848
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[<c0112588>] (unwind_backtrace) from [<c010e070>] (show_stack+0x10/0x14)
[<c010e070>] (show_stack) from [<c0afb010>] (dump_stack+0xb4/0xe0)
[<c0afb010>] (dump_stack) from [<c01272e0>] (__warn+0xf4/0x10c)
[<c01272e0>] (__warn) from [<c01273a8>] (warn_slowpath_fmt+0xb0/0xb8)
[<c01273a8>] (warn_slowpath_fmt) from [<c07d105c>] (devfreq_update_status+0xc0/0x188)
[<c07d105c>] (devfreq_update_status) from [<c07d2d70>] (devfreq_set_target+0xb0/0x15c)
[<c07d2d70>] (devfreq_set_target) from [<c07d3598>] (devfreq_suspend+0x2c/0x64)
[<c07d3598>] (devfreq_suspend) from [<c05de0b0>] (dpm_suspend+0xa4/0x57c)
[<c05de0b0>] (dpm_suspend) from [<c05def74>] (dpm_suspend_start+0x98/0xa0)
[<c05def74>] (dpm_suspend_start) from [<c0195b58>] (suspend_devices_and_enter+0xec/0xc74)
[<c0195b58>] (suspend_devices_and_enter) from [<c0196a20>] (pm_suspend+0x340/0x410)
[<c0196a20>] (pm_suspend) from [<c019480c>] (state_store+0x6c/0xc8)
[<c019480c>] (state_store) from [<c033fc50>] (kernfs_fop_write+0x10c/0x228)
[<c033fc50>] (kernfs_fop_write) from [<c02a6d3c>] (__vfs_write+0x30/0x1d0)
[<c02a6d3c>] (__vfs_write) from [<c02a9afc>] (vfs_write+0xa4/0x180)
[<c02a9afc>] (vfs_write) from [<c02a9d58>] (ksys_write+0x60/0xd8)
[<c02a9d58>] (ksys_write) from [<c0101000>] (ret_fast_syscall+0x0/0x28)
Exception stack(0xed3d7fa8 to 0xed3d7ff0)
...
irq event stamp: 9667
hardirqs last enabled at (9679): [<c0b1e7c4>] _raw_spin_unlock_irq+0x20/0x58
hardirqs last disabled at (9698): [<c0b16a20>] __schedule+0xd8/0x818
softirqs last enabled at (9694): [<c01026fc>] __do_softirq+0x4fc/0x5fc
softirqs last disabled at (9719): [<c012fe68>] irq_exit+0x16c/0x170
---[ end trace 41ac5b57d046bdbc ]---
------------[ cut here ]------------
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
MCCPU boosts up very aggressively by 800% and boosts down very mildly by
10%. This doesn't work well when system is idling because the very slow
de-boosting results in lots of consecutive-down interrupts, in result
memory stays clocked high and CPU doesn't enter deepest idling state
instead of keeping memory at lowest freq and having CPU cluster turned
off. A more faster de-boosting fixes the case of idling system and doesn't
affect the case of an active system.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The ACTMON governor is interrupt-driven and currently hardware's polling
interval is fixed to 16ms in the driver. Devfreq supports variable polling
interval by the generic governors, let's re-use the generic interface for
changing of the polling interval. Now the polling interval can be changed
dynamically via /sys/class/devfreq/devfreq0/polling_interval.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Currently interrupt-driven governors (like NVIDIA Tegra30 ACTMON governor)
are used to set polling_ms=0 in order to avoid periodic polling of device
status by devfreq core. This means that polling interval can't be changed
by userspace for such governors.
The new governor flag allows interrupt-driven governors to convey that
devfreq core shouldn't perform polling of device status and thus generic
devfreq polling interval could be supported by these governors now.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The dependency threshold designates a memory activity level below which
CPU's frequency isn't accounted. Currently the threshold is given in
"memory cycle" units and that value depends on the polling interval which
is fixed to 12ms in the driver. Later on we'd want to add support for a
variable polling interval and thus the threshold value either needs to be
scaled in accordance to the polling interval or it needs to be represented
in a units that do not depend on the polling interval.
It is nicer to have threshold value being defined independently of the
polling interval, thus this patch converts the dependency threshold units
from "cycle" to "kHz". Having this change as a separate-preparatory patch
will make easier to follow further patches.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Consecutive interrupts should be disabled when boosting is completed.
Currently the disabling of "lower" interrupt happens only for MCCPU
monitor that uses dependency threshold, but even in a case of MCCPU the
interrupt isn't getting disabled if CPU's activity is above the threshold.
This results in a lot of dummy interrupt requests. The boosting feature is
used by both MCCPU and MCALL, boosting should be stopped once it reaches 0
for both of the monitors and regardless of the activity level.
The boosting stops to grow once the maximum limit is hit and thus the
"upper" interrupt needs to be disabled when the limit is reached.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Consecutive up/down interrupt-bit is set in the interrupt status register
only if that interrupt was previously enabled. Thus enabling the already
enabled interrupt doesn't do much for us.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
It's not very correct to include mod_devicetable.h for the OF device
drivers and of_device.h should be included instead.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The consecutive-down event tells that we should perform frequency
de-boosting, but boosting is in a reset state on start and hence the
event won't do anything useful for us and it will be just a dummy
interrupt request.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Governor could be stopped while boosting is active. We have assumption
that everything is reset on governor's restart, including the boosting
value, which was missed.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There is no point in receiving of the notifications while governor is
stopped, let's keep them disabled like we do for the CPU freq-change
notifications. This also fixes a potential use-after-free bug if
notification happens after device's removal.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The CPU's client need to take into account that CPUFreq may change
while memory activity not, staying high. Thus an appropriate frequency
notifier should be used in addition to the clk-notifier.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Part of the code uses Hz units and the other kHz, let's switch to kHz
everywhere for consistency. A small benefit from this change (besides
code's cleanup) is that now powertop utility correctly displays devfreq's
stats, for some reason it expects them to be in kHz.
Tested-by: Peter Geis <pgwipeout@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There is another kHz-conversion bug in the code, resulting in integer
overflow. Although, this time the resulting value is 4294966296 and it's
close to ULONG_MAX, which is okay in this case.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There is no need in a write-barrier now, given that interrupt masking is
handled by CPU's GIC now. Hence we know exactly that interrupt won't fire
after stopping the devfreq's governor. In other cases we don't care about
potential buffering of the writes to hardware and thus there is no need to
stall CPU.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There is no real need to keep interrupt always-enabled, will be nicer
to keep it disabled while governor is inactive.
Suggested-by: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
IRQ numbers are always positive, hence the corresponding variable should
be unsigned to keep types consistent. This is a minor change that cleans
up code a tad more.
Suggested-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Tested-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The error code is propagated to the caller, so there is no need to keep
it additionally in the unused variable.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
There is no locking in this sysfs show function so stats printing can
race with a devfreq_update_status called as part of freq switching or
with initialization.
Also add an assert in devfreq_update_status to make it clear that lock
must be held by caller.
Fixes: 39688ce6fa ("PM / devfreq: account suspend/resume for stats")
Cc: stable@vger.kernel.org
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The governor is initialized after sysfs attributes become visible so in
theory the governor field can be NULL here.
Fixes: bcf23c79c4 ("PM / devfreq: Fix available_governor sysfs")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Before creating a new devfreq device devfreq_add_device() checks
if there is already a devfreq dev associated with the requesting
device (parent). If that's the case the function rejects to create
another devfreq dev for that parent and logs an error. The error
message is very unspecific, make it a bit more explicit.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
The recent commit of
PM / devfreq: passive: Use non-devm notifiers
had incurred compiler warning, "unused variable 'dev'".
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The devfreq passive governor registers and unregisters devfreq
transition notifiers on DEVFREQ_GOV_START/GOV_STOP using devm wrappers.
If devfreq itself is registered with devm then a warning is triggered on
rmmod from devm_devfreq_unregister_notifier. Call stack looks like this:
devm_devfreq_unregister_notifier+0x30/0x40
devfreq_passive_event_handler+0x4c/0x88
devfreq_remove_device.part.8+0x6c/0x9c
devm_devfreq_dev_release+0x18/0x20
release_nodes+0x1b0/0x220
devres_release_all+0x78/0x84
device_release_driver_internal+0x100/0x1c0
driver_detach+0x4c/0x90
bus_remove_driver+0x7c/0xd0
driver_unregister+0x2c/0x58
platform_driver_unregister+0x10/0x18
imx_devfreq_platdrv_exit+0x14/0xd40 [imx_devfreq]
This happens because devres_release_all will first remove all the nodes
into a separate todo list so the nested devres_release from
devm_devfreq_unregister_notifier won't find anything.
Fix the warning by calling the non-devm APIS for frequency notification.
Using devm wrappers is not actually useful for a governor anyway: it
relies on the devfreq core to correctly match the GOV_START/GOV_STOP
notifications.
Fixes: 996133119f ("PM / devfreq: Add new passive governor")
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reuse opp core code for setting bus clock and voltage. As a side
effect this allow usage of coupled regulators feature (required
for boards using Exynos5422/5800 SoCs) because dev_pm_opp_set_rate()
uses regulator_set_voltage_triplet() for setting regulator voltage
while the old code used regulator_set_voltage_tol() with fixed
tolerance. This patch also removes no longer needed parsing of DT
property "exynos,voltage-tolerance" (no Exynos devfreq DT node uses
it). After applying changes both functions exynos_bus_passive_target()
and exynos_bus_target() have the same code, so remove
exynos_bus_passive_target(). In exynos_bus_probe() replace it with
exynos_bus_target.
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Regulators should be enabled before clocks to avoid h/w hang. This
require change in exynos_bus_probe() to move exynos_bus_parse_of()
after exynos_bus_parent_parse_of() and change in error handling.
Similar change is needed in exynos_bus_exit() where clock should be
disabled before regulators.
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Correct the documentation for devm_devfreq_remove_device() argument.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch adds posibility to choose what type of data should be counted
by the PPMU counter. Now the type comes from DT where the event has been
defined. When there is no 'event-data-type' the default value is used,
which is 'read+write data in bytes'.
It is needed when you want to know not only read+write data bytes but
i.e. only write data in byte, or number of read requests, etc.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
[Updated property by MyungJoo. data_type --> event_type]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The patch changes the way how the 'ops' gets populated for different
device versions. The matching function now uses 'of_device_id' in order
to identify the device type.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Compile-testing the new driver on platforms without CONFIG_COMMON_CLK
leads to a link error:
drivers/devfreq/tegra20-devfreq.o: In function `tegra_devfreq_target':
tegra20-devfreq.c:(.text+0x288): undefined reference to `clk_set_min_rate'
Add a dependency on COMMON_CLK to avoid this.
Fixes: 1d39ee8dad6d ("PM / devfreq: Introduce driver for NVIDIA Tegra20")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Define new performance events supported by Exynos5422 SoC counters.
The counters are built-in in Dynamic Memory Controller and provide
information regarding memory utilization.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
A bit unexpectedly (but still documented), request_module may
return a positive value, in case of a modprobe error.
This is currently causing issues in the devfreq framework.
When a request_module exits with a positive value, we currently
return that via ERR_PTR. However, because the value is positive,
it's not a ERR_VALUE proper, and is therefore treated as a
valid struct devfreq_governor pointer, leading to a kernel oops.
Fix this by returning -EINVAL if request_module returns a positive
value.
Fixes: b53b012805 ("PM / devfreq: Fix static checker warning in try_then_request_governor")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Add devfreq driver for NVIDIA Tegra20 SoC's. The driver periodically
reads out Memory Controller counters and adjusts memory frequency based
on the memory clients activity.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
[Removed MAINTAINERS updates by MyungJoo so that it can be sent elsewhere.]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
In order to reflect that driver serves NVIDIA Tegra30 and later SoC
generations, let's rename the driver's source file to "tegra30-devfreq.c".
This will make driver files to look more consistent after addition of a
driver for Tegra20.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The driver's compilation doesn't have any specific dependencies, hence
the COMPILE_TEST option can be supported in Kconfig.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The devfreq driver can be used on Tegra30 without any code change and
it works perfectly fine, the default Tegra124 parameters are good enough
for Tegra30.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
[Modified by MyungJoo to depends on Tegra30/114/124/210 only]
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Move hardware configuration to governor's start/resume methods.
This allows to re-initialize hardware counters and reconfigure
cleanly if governor was stopped/paused. That is needed because we
are not aware of all hardware changes that happened while governor
was stopped and the paused state may get out of sync with reality,
hence it's better to start with a clean slate after the pause. In
a result there is no memory bandwidth starvation after resume from
suspend-to-ram that results in display controller underflowing that
happens on resume because of improper decision made by devfreq about
the required memory frequency. This change also cleans up code a tad
by moving hardware-configuration code into a single location.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
There is no need to register the ACTMON's governor separately from
the driver, hence let's move the registration into the driver's probe
function for consistency and to make code cleaner a tad.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The ACTMON's governor supports only the Tegra's devfreq device and there
is no need to use any other governor, hence let's mark Tegra governor as
immutable to permanently stick it with Tegra's devfreq device.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The frequency value potentially could change in-between. It doesn't
cause any real problem at all right now, but that could change in the
future. Hence let's avoid the inconsistency.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reset hardware, disable ACTMON clock, release OPP's and handle all
possible error cases correctly, maintaining the correct tear down
order. Also use devm_platform_ioremap_resource() which is now available
in the kernel.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
There is no guarantee that interrupt handling isn't running in parallel
with tegra_actmon_disable_interrupts(), hence it is necessary to protect
DEV_CTRL register accesses and clear IRQ status with ACTMON's IRQ being
disabled in the Interrupt Controller in order to ensure that device
interrupt is indeed being disabled.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
There is no real need in the primary interrupt handler, hence move
everything to the secondary (threaded) handler. In a result locking
is consistent now and there are no potential races with the interrupt
handler because it is protected with the devfreq's mutex.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
There is no real benefit from doing so, hence let's drop that rate setting
for consistency.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The clk_set_min_rate() could fail and in this case clk_set_rate() sets
rate to 0, which may drop EMC rate to minimum and make machine very
difficult to use.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The write memory barrier isn't needed because the BUS buffer is flushed
by read after write that happens after the removed wmb(), we will also
use readl() instead of the relaxed version to ensure that read is indeed
completed.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
There is no need to insert memory barrier on each readl/writel
invocation, hence use the relaxed versions.
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The kHz to Hz is incorrectly converted in a few places in the code,
this results in a wrong frequency being calculated because devfreq core
uses OPP frequencies that are given in Hz to clamp the rate, while
tegra-devfreq gives to the core value in kHz and then it also expects to
receive value in kHz from the core. In a result memory freq is always set
to a value which is close to ULONG_MAX because of the bug. Hence the EMC
frequency is always capped to the maximum and the driver doesn't do
anything useful. This patch was tested on Tegra30 and Tegra124 SoC's, EMC
frequency scaling works properly now.
Cc: <stable@vger.kernel.org> # 4.14+
Tested-by: Steev Klimaszewski <steev@kali.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch add basic tracing of the devfreq workqueue and delayed work.
It aims to capture changes of the polling intervals and device state.
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Trusted Firmware-A (TF-A) for rk3399 implements a SiP call to get the
on-die termination (ODT) and auto power down parameters from kernel,
this patch adds the functionality to do this. Also, if DDR clock
frequency is lower than the on-die termination (ODT) disable frequency
this driver should disable the DDR ODT.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Some rk3399 GRF (Generic Register Files) definitions can be used for
different drivers. Move these definitions to a common include so we
don't need to duplicate these definitions.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Gaël PORTAY <gael.portay@collabora.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Force all Exynos buses to safe operation points before doing the system
reboot operation. There are board on which some aggressive power saving
operation points are behind the capabilities of the bootloader to properly
reset the hardware and boot the board. This way one can avoid board crash
early after reboot.
This fixes reboot issue on OdroidU3 board both with eMMC and SD boot.
Reported-by: Markus Reichl <m.reichl@fivetechno.de>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The patch 23c7b54ca1cd: "PM / devfreq: Fix devfreq_add_device() when
drivers are built as modules." leads to the following static checker
warning:
drivers/devfreq/devfreq.c:1043 governor_store()
warn: 'governor' can also be NULL
The reason is that the try_then_request_governor() function returns both
error pointers and NULL. It should just return error pointers, so fix
this by returning a ERR_PTR to the error intead of returning NULL.
Fixes: 23c7b54ca1 ("PM / devfreq: Fix devfreq_add_device() when drivers are built as modules.")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
If the new governor fails to start, switch back to old governor so that the
devfreq state is not left in some weird limbo.
[Myungjoo: assume fatal on revert failure and set df->governor to NULL]
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Saravana Kannan <skannan@codeaurora.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This variable is not used after initialization, so
remove it. And in order to unify the code style,
move the location where the dev_get_drvdata is called
by the way.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The semicolon is unneeded, so remove it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The semicolon is unneeded, so remove it.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Following up with complaints on inconsistent indentation from
Yangtao Li, this fixes indentation inconsistency.
In principle, this tries to put arguments aligned to the left
including the first argument except for the case where
the first argument is on the far-right side.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Yangtao Li <tiny.windzz@gmail.com>
devm_kzalloc() could fail, so insert a check of its return value. And
if it fails, returns -ENOMEM.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
'devfreq' is malloced in devfreq_add_device() and should be freed in
the error handling cases, otherwise it will cause memory leak.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
For instances using of_node_cmp, this has the side effect of now using
case sensitive comparisons. This should not matter for any FDT based
system which all of these are.
Cc: Chanwoo Choi <cw00.choi@samsung.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-samsung-soc@vger.kernel.org
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch adds implementation for global suspend/resume for
devfreq framework. System suspend will next use these functions.
Suggested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The patch prepares devfreq device for handling suspend/resume
functionality. The new fields will store needed information during this
process. Devfreq framework handles opp-suspend DT entry and there is no
need of modyfications in the drivers code. It uses atomic variables to
make sure no race condition affects the process.
Suggested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The refactoring is needed for the new client in devfreq: suspend.
To avoid code duplication, move it to the new local function
devfreq_set_target.
Suggested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Suggested-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lukasz Luba <l.luba@partner.samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
kfree has taken the null pointer into account. hence it is safe
to remove the redundant null pointer check before kfree.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
device_release() is freeing the resources before calling the device
specific release callback which is, in the case of devfreq, stopping
the governor.
It is a problem as some governors are using the device resources. e.g.
simpleondemand which is using the devfreq deferrable monitoring work. If it
is not stopped before the resources are freed, it might lead to a use after
free.
Signed-off-by: Vincent Donnefort <vincent.donnefort@arm.com>
Reviewed-by: John Einar Reitan <john.reitan@arm.com>
[cw00.choi: Fix merge conflict]
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
In preparation to remove the node name pointer from struct device_node,
convert printf users to use the %pOFn format specifier.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Currently update_devfreq() is only visible to devfreq governors outside
of devfreq.c. Make it public to allow drivers that adjust devfreq policies
to cause a re-evaluation of the frequency after a policy change.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Several governors use the user space limits df->min/max_freq to adjust
the target frequency. This is not necessary, since update_devfreq()
already takes care of this. Instead the governor can request the available
min/max frequency by setting the target frequency to DEVFREQ_MIN/MAX_FREQ
and let update_devfreq() take care of any adjustments.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Commit ab8f58ad72 ("PM / devfreq: Set min/max_freq when adding the
devfreq device") initializes df->min/max_freq with the min/max OPP when
the device is added. Later commit f1d981eaec ("PM / devfreq: Use the
available min/max frequency") adds df->scaling_min/max_freq and the
following to the frequency adjustment code:
max_freq = MIN(devfreq->scaling_max_freq, devfreq->max_freq);
With the current handling of min/max_freq this is incorrect:
Even though df->max_freq is now initialized to a value != 0 user space
can still set it to 0, in this case max_freq would be 0 instead of
df->scaling_max_freq as intended. In consequence the frequency adjustment
is not performed:
if (max_freq && freq > max_freq) {
freq = max_freq;
To fix this set df->min/max freq to the min/max OPP in max/max_freq_store,
when the user passes a value of 0. This also prevents df->max_freq from
being set below the min OPP when df->min_freq is 0, and similar for
min_freq. Since it is now guaranteed that df->min/max_freq can't be 0 the
checks for this case can be removed.
Fixes: f1d981eaec ("PM / devfreq: Use the available min/max frequency")
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Drop the custom MIN/MAX macros in favour of the standard min/max from
kernel.h
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
When the devfreq driver and the governor driver are built as modules,
the call to devfreq_add_device() or governor_store() fails because the
governor driver is not loaded at the time the devfreq driver loads. The
devfreq driver has a build dependency on the governor but also should
have a runtime dependency. We need to make sure that the governor driver
is loaded before the devfreq driver.
This patch fixes this bug by adding a try_then_request_governor()
function. First tries to find the governor, and then, if it is not found,
it requests the module and tries again.
Fixes: 1b5c1be2c8 (PM / devfreq: map devfreq drivers to governor using name)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
The opp table is not removed when the driver is unloaded neither when
there is an error within probe, so if the driver is reloaded the opp
core shows the following warning:
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
200000000, volt: 900000, enabled: 1. New: freq: 200000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
400000000, volt: 900000, enabled: 1. New: freq: 400000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
666000000, volt: 900000, enabled: 1. New: freq: 666000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
800000000, volt: 900000, enabled: 1. New: freq: 800000000,
volt: 900000, enabled: 1
rk3399-dmc-freq dmc: _opp_add: duplicate OPPs detected. Existing: freq:
928000000, volt: 900000, enabled: 1. New: freq: 928000000,
volt: 900000, enabled: 1
This patch fixes the error path in the probe function and adds a .remove
function to properly cleanup the opp table on unloading.
Fixes: 5a893e31a6 (PM / devfreq: rockchip: add devfreq driver for rk3399 dmc)
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Commit ab8f58ad72 ("PM / devfreq: Set min/max_freq when adding
the devfreq device") introduced the initialization of the user
limits min/max_freq from the lowest/highest available OPPs. Later
commit f1d981eaec ("PM / devfreq: Use the available min/max
frequency") added scaling_min/max_freq, which actually represent
the frequencies of the lowest/highest available OPP. scaling_min/
max_freq are initialized with the values from min/max_freq, which
is totally correct in the context, but a bit awkward to read.
Swap the initialization and assign scaling_min/max_freq with the
OPP freqs and then the user limts min/max_freq with scaling_min/
max_freq.
Needless to say that this change is a NOP, intended to improve
readability.
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Fix some spelling mistakes in error and debug messages.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
We just return -EPROBE_DEFER error code to caller and do not
print error message when try to get center logic regulator
and DMC clock defer.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
We have already wait dcf done in ATF, so don't need wait dcf irq
in kernel, besides, clear dcf irq in kernel will import competiton
between kernel and ATF, only handle dcf irq in ATF is a better way.
Signed-off-by: Lin Huang <hl@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Never directly free @dev after calling device_register() or
device_unregister(), even if device_register() returned an error.
Always use put_device() to give up the reference initialized.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Omit an extra message for a memory allocation failure in this function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
df->governor is being dereferenced before it is null checked,
hence there is a potential null pointer dereference.
Notice that df->governor is being null checked at line 1004:
if (df->governor) {, which implies it might be null.
Fix this by null checking df->governor before dereferencing it.
Addresses-Coverity-ID: 1401988 ("Dereference before null check")
Fixes: bcf23c79c4 ("PM / devfreq: Fix available_governor sysfs")
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Propagate the error of devfreq_add_device() in devm_devfreq_add_device()
rather than statically returning ENOMEM. This makes it slightly faster
to pinpoint the cause of a returned error.
Fixes: 8cd84092d3 ("PM / devfreq: Add resource-managed function for devfreq device")
Cc: stable@vger.kernel.org
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
* pm-devfreq:
PM / devfreq: Define the constant governor name
PM / devfreq: Remove unneeded conditional statement
PM / devfreq: Show the all available frequencies
PM / devfreq: Change return type of devfreq_set_freq_table()
PM / devfreq: Use the available min/max frequency
Revert "PM / devfreq: Add show_one macro to delete the duplicate code"
PM / devfreq: Set min/max_freq when adding the devfreq device
* pm-tools:
tools/power/cpupower: add libcpupower.so.0.0.1 to .gitignore
tools/power/cpupower: Add 64 bit library detection
MAINTAINERS: add maintainer for tools/power/cpupower
cpupower: Fix no-rounding MHz frequency output
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to that, the devfreq device uses the governor name when adding
the itself. In order to prevent the mistake used the wrong governor name,
this patch defines the governor name as a constant and then uses them
instead of using the string directly.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: linux-samsung-soc@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
The freq_table array of each devfreq device is always not NULL.
In result, it is unneeded to check whether profile->freq_table
is NULL or not.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The commit a76caf55e5 ("thermal: Add devfreq cooling") allows
the devfreq device to use the cooling device. When the cooling down
are required, the devfreq_cooling.c disables the OPP entry with
the dev_pm_opp_disable(). In result, 'available_frequencies'[1]
sysfs node never came to show the all available frequencies.
[1] /sys/class/devfreq/.../available_frequencies
So, this patch uses the 'freq_table' in the 'struct devfreq_dev_profile'
in order to show the all available frequencies.
- If 'freq_table' is NULL, devfreq core initializes them by using OPP values.
- If 'freq_table' is initialized, devfreq core just uses the 'freq_table'.
And this patch adds some comment about the sort way of 'freq_table'.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This patch changes the return type of devfreq_set_freq_table()
from 'void' to 'int' in order to check whether it fails or not.
And This patch just removes the 'devfreq' prefix and the description
of function. Because the helper functions are only used by the devfreq.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
The commit a76caf55e5 ("thermal: Add devfreq cooling") is able
to disable OPP as a cooling device. In result, both update_devfreq()
and {min|max}_freq_show() have to consider the 'opp->available'
status of each OPP.
So, this patch adds the 'scaling_{min|max}_freq' to struct devfreq
in order to indicate the available mininum and maximum frequency
by adjusting OPP interface such as dev_pm_opp_{disable|enable}().
The 'scaling_{min|max}_freq' are used for on both update_devfreq()
and {min|max}_freq_show().
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
This reverts commit 3104fa3081.
The {min|max}_freq_show() show the stored value of the struct devfreq.
But, if the drivers/thermal/devfreq_cooling.c disables the specific
frequency value, {min|max}_freq_show() have to check this situation
before showing the stored value. So, this patch revert the macro
in order to add the additional codes.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Prior to that, the min/max_freq of the devfreq device are always zero
before the user changes the min/max_freq through sysfs entries.
It might make the confusion for the min/max_freq.
This patch initializes the available min/max_freq by using the OPP
during adding the devfreq device.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Marek Szyprowski