Power Management Quality of Service is not supported or used by the VF
driver.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change "return (EXPR);" to "return EXPR;"
return is not a function, parentheses are not required.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fresh skbs have ip_summed set to CHECKSUM_NONE (0)
We can avoid setting again skb->ip_summed to CHECKSUM_NONE in drivers.
Introduce skb_checksum_none_assert() helper so that we keep this
assertion documented in driver sources.
Change most occurrences of :
skb->ip_summed = CHECKSUM_NONE;
by :
skb_checksum_none_assert(skb);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on patches from Sonny Rao and Milton Miller...
Combined the patches to fix up clean_tx_irq and clean_rx_irq.
The PowerPC architecture does not require loads to independent bytes
to be ordered without adding an explicit barrier.
In ixgbe_clean_rx_irq we load the status bit then load the packet data.
With packet split disabled if these loads go out of order we get a
stale packet, but we will notice the bad sequence numbers and drop it.
The problem occurs with packet split enabled where the TCP/IP header
and data are in different descriptors. If the reads go out of order
we may have data that doesn't match the TCP/IP header. Since we use
hardware checksumming this bad data is never verified and it makes it
all the way to the application.
This bug was found during stress testing and adding this barrier has
been shown to fix it. The bug can manifest as a data integrity issue
(bad payload data) or as a BUG in skb_pull().
This was a nasty bug to hunt down, if people agree with the fix I think
it's a candidate for stable.
Previously Submitted to e1000-devel only for ixgbe
http://marc.info/?l=e1000-devel&m=126593062701537&w=3
We've now seen this problem hit with other device drivers (e1000e mostly)
So I'm resubmitting with fixes for other Intel Device Drivers with
similar issues.
CC: Milton Miller <miltonm@bga.com>
CC: Anton Blanchard <anton@samba.org>
CC: Sonny Rao <sonnyrao@us.ibm.com>
CC: stable <stable@kernel.org>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits)
phy/marvell: add 88ec048 support
igb: Program MDICNFG register prior to PHY init
e1000e: correct MAC-PHY interconnect register offset for 82579
hso: Add new product ID
can: Add driver for esd CAN-USB/2 device
l2tp: fix export of header file for userspace
can-raw: Fix skb_orphan_try handling
Revert "net: remove zap_completion_queue"
net: cleanup inclusion
phy/marvell: add 88e1121 interface mode support
u32: negative offset fix
net: Fix a typo from "dev" to "ndev"
igb: Use irq_synchronize per vector when using MSI-X
ixgbevf: fix null pointer dereference due to filter being set for VLAN 0
e1000e: Fix irq_synchronize in MSI-X case
e1000e: register pm_qos request on hardware activation
ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice
net: Add getsockopt support for TCP thin-streams
cxgb4: update driver version
cxgb4: add new PCI IDs
...
Manually fix up conflicts in:
- drivers/net/e1000e/netdev.c: due to pm_qos registration
infrastructure changes
- drivers/net/phy/marvell.c: conflict between adding 88ec048 support
and cleaning up the IDs
- drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req
conflict (registration change vs marking it static)
Both igbvf and ixgbevf should set addr_assign_type to NET_ADDR_RANDOM
so udev creates persistent net rules by matching the device path.
Do this by using the dev_hw_addr_random helper function.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All current users of pm_qos_add_request() have the ability to supply
the memory required by the pm_qos routines, so make them do this and
eliminate the kmalloc() with pm_qos_add_request(). This has the
double benefit of making the call never fail and allowing it to be
called from atomic context.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: mark gross <markgross@thegnar.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits)
qlcnic: adding co maintainer
ixgbe: add support for active DA cables
ixgbe: dcb, do not tag tc_prio_control frames
ixgbe: fix ixgbe_tx_is_paused logic
ixgbe: always enable vlan strip/insert when DCB is enabled
ixgbe: remove some redundant code in setting FCoE FIP filter
ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp
ixgbe: fix header len when unsplit packet overflows to data buffer
ipv6: Never schedule DAD timer on dead address
ipv6: Use POSTDAD state
ipv6: Use state_lock to protect ifa state
ipv6: Replace inet6_ifaddr->dead with state
cxgb4: notify upper drivers if the device is already up when they load
cxgb4: keep interrupts available when the ports are brought down
cxgb4: fix initial addition of MAC address
cnic: Return SPQ credit to bnx2x after ring setup and shutdown.
cnic: Convert cnic_local_flags to atomic ops.
can: Fix SJA1000 command register writes on SMP systems
bridge: fix build for CONFIG_SYSFS disabled
ARCNET: Limit com20020 PCI ID matches for SOHARD cards
...
Fix up various conflicts with pcmcia tree drivers/net/
{pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and
wireless/orinoco/spectrum_cs.c} and feature removal
(Documentation/feature-removal-schedule.txt).
Also fix a non-content conflict due to pm_qos_requirement getting
renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the string based list management to a handle base
implementation to help with the hot path use of pm-qos, it also renames
much of the API to use "request" as opposed to "requirement" that was
used in the initial implementation. I did this because request more
accurately represents what it actually does.
Also, I added a string based ABI for users wanting to use a string
interface. So if the user writes 0xDDDDDDDD formatted hex it will be
accepted by the interface. (someone asked me for it and I don't think
it hurts anything.)
This patch updates some documentation input I got from Randy.
Signed-off-by: markgross <mgross@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Nicholas Nunley <nicholasx.d.nunley@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to increment nr_frags because skb_fill_page_desc increments
it.
Signed-off-by: Koki Sanagi <sanagi.koki@jp.fujitsu.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Converts the list and the core manipulating with it to be the same as uc_list.
+uses two functions for adding/removing mc address (normal and "global"
variant) instead of a function parameter.
+removes dev_mcast.c completely.
+exposes netdev_hw_addr_list_* macros along with __hw_addr_* functions for
manipulation with lists on a sandbox (used in bonding and 80211 drivers)
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Previously the driver tweaked txqueuelen to avoid false Tx hang reports seen at half duplex.
This had the effect of overriding user set values on link change/reset. Testing shows that
adjusting only the timeout factor is sufficient to prevent Tx hang reports at half duplex.
Based on e1000e patch by Franco Fichtner <franco@lastsummer.de>
CC: Franco Fichtner <franco@lastsummer.de>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces dev->mc_count in all drivers (hopefully I didn't miss
anything). Used spatch and did small tweaks and conding style changes when
it was suitable.
Jirka
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change fixes an issue in igbvf with mapped_as_page being left set
after a page is unmapped which results in buffers which are mapped via map
single being unmapped as page.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Found this problem when testing IPv6 from a KVM guest to a remote
host via e1000e device on the host.
The following patch fixes the check for IPv6 GSO packet in Intel
ethernet drivers to use skb_is_gso_v6(). SKB_GSO_DODGY is also set
when packets are forwarded from a guest.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After removing the skb_dma_map/unmap calls the exception handling in
igb_tx_map_adv is not correct. The issue is that the count value was not
being correctly handled so as a result we were not rewinding the ring as
back as we should have been.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable count and i are unsigned so the (<|>=)0 tests do not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section
in every case.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the %pM kernel extension to display the MAC address.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Alexander Duyck <alexander.h.duyck@intel.com>
This change makes it so that reset/interrupt storms can be avoided when
there are mailbox issues. The new behavior is to only allow the device to
trigger mailbox related resets only once every 10 seconds.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only files where David Miller is the primary git-signer.
wireless, wimax, ixgbe, etc are not modified.
Compile tested x86 allyesconfig only
Not all files compiled (not x86 compatible)
Added a few > 80 column lines, which I ignored.
Existing checkpatch complaints ignored.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the skb_dma_map/unmap calls from the igbvf driver due to
the fact that it does not play well with HW IOMMU when combined with
transmitting cloned skbs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not as fancy as coccinelle. Checkpatch errors ignored.
Compile tested allyesconfig x86, not all files compiled.
grep -rPl --include=*.[ch] "\brequest_irq\s*\([^,\)]+,\s*\&" drivers/net | while read file ; do \
perl -i -e 'local $/; while (<>) { s@(\brequest_irq\s*\([^,\)]+,\s*)\&@\1@g ; print ; }' $file ;\
done
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch resolves a memory leak which occurs while changing the ring size
while the interface is down.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These string query operations were supposed to be replaced by the
generic get_sset_count() starting in 2007. Convert the remaining
implementations.
Also remove calls to these operations to initialise drvinfo->n_stats.
The ethtool core code already does that.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Neil Horman <nhorman@txudriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of some bogus return wrapping as well.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VF driver was not correctly recognizing that it did not correctly set
it's mac address. As a result the VF driver was unable to receive network
traffic until being unloaded and reloaded. The issue was root caused to
the fact that the CTS bit was not taken into account when checking for the
request being NAKed.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI drivers that implement the struct pci_error_handlers' error_detected
callback should return PCI_ERS_RESULT_DISCONNECT if the state passed in is
pci_channel_io_perm_failure. This patch fixes the issue for igbvf.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change resolves some warnings seen with DMA debugging enabled in which
we were mapping skb->data with size + NET_IP_ALIGN and unmapping it with
just size.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're about to make DMA_nnBIT_MASK() emit `deprecated' warnings. Convert the
remaining stragglers which are visible to the x86_64 build.
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Eric Moore <Eric.Moore@lsil.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Yi Zou <yi.zou@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
skb_dma_unmap() is quite expensive for small packets,
because we use two different cache lines from skb_shared_info.
One to access nr_frags, one to access dma_maps[0]
Instead of dma_maps being an array of MAX_SKB_FRAGS + 1 elements,
let dma_head alone in a new dma_head field, close to nr_frags,
to reduce cache lines misses.
Tested on my dev machine (bnx2 & tg3 adapters), nice speedup !
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Second round of drivers for Gb cards (and NIU one I forgot in the 10GB round)
Now that core network takes care of trans_start updates, dont do it
in drivers themselves, if possible. Drivers can avoid one cache miss
(on dev->trans_start) in their start_xmit() handler.
Exceptions are NETIF_F_LLTX drivers
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up a number of unused or unneeded feature flags. As a
result of these changes the user should now be able to enable or disable rx
checksumming via ethtool.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The igbvbf driver exposed several unused extrnal references due to the fact
that code was copied from igb and then some functionality was removed.
This changes that so that unused functions are either removed or made
static.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Greg Rose