The NAND/NOR flash pin lists (da850_nand_pins/da850_nor_pins) are purely board
specific and as such shouldn't be in da850.c -- copy them to board-da850-evm.c,
renaming to da850_evm_nand_pins/da850_evm_nor_pins respectively, and merge the
two lists in da850.c into one, representing the EMIF 2.5 module as a whole,
just like we have it in da830.c...
While at it, remove the '__init' modifier from da850_evm_setup_nor_nand() as
this function is called from non '__init' code...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Tested-by: Ben Gardiner <bengardiner@nanometrics.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Keep PLL0 SYSCLK3 at a constant rate of 100MHz. This enables the AEMIF
timing to remain valid even as the PLL0 output is changed by cpufreq
driver to save power.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The Sitara AM17x SoCs from TI are an OMAP-L137 pin-to-pin
compatible ARM9 microprocessor offering from TI.
The Sitara AM18x SoCs from TI are an OMAP-L138 pin-to-pin
compatible ARM9 microprocessor offering from TI.
More information about these processors available at:
www.ti.com/am1x
Because of their compatibiliy with OMAP-L1x, the kernel
support for OMAP-L1x is fully relevant to AM1x processors.
This patch updates the Kconfig prompt and help text to include
the AM1x part names to help users select configurations required
for these parts easily.
Also, the hardware information that shows up in /proc/cpuinfo
is updated to show applicability of the respective OMAP-L1x EVMs
for AM1x parts.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Without this cleanup, sparse checker reports warnings of the type:
CHECK arch/arm/mach-davinci/board-da850-evm.c
arch/arm/mach-davinci/board-da850-evm.c:112:22: warning: symbol 'da850_evm_nandflash_partition' was not declared. Should it be static?
The nand flash partitions and regulator supplies are used within
the EVM file and so should have been static
This patch has been boot tested on DA830 and DA850 EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci:
davinci: dm646x EVM: Specify reserved EDMA channel/slots
davinci: da8xx/omapl EVM: Specify reserved channels/slots
davinci: support for EDMA resource sharing
davinci: edma: provide ability to detect insufficient CC info data
davinci: da8xx: sparse cleanup: remove duplicate entries in irq priorities
davinci: DM365: fixed second serial port
Davinci: tnetv107x evm board initial support
Davinci: tnetv107x initial gpio support
Davinci: tnetv107x soc support
Davinci: tnetv107x decompresser uart definitions
Davinci: generalized debug macros
The drivers on da8xx/omapl EVMs do not utilize all the channels
and slots provided by EDMA. Some of these are better utilitzed by
the DSP on the SoC for speeding up codec operations.
Reserve these channels/slots for the DSP.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Per the da850/omap-l138 Beta EVM SOM schematic, the DEFDCDC2 and
DEFDCDC3 lines are tied high. This leads to a 3.3V IO and 1.2V CVDD
voltage.
Pass the right platform data to the TPS6507x driver so it can operate
on the DEFDCDC{2,3}_HIGH register to read and change voltage levels.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Currently the EDMA queue to be used by for servicing ASP through
internal RAM is fixed to EDMAQ_0 and that to service internal RAM
from external RAM is fixed to EDMAQ_1.
This may not be the desirable configuration on all platforms. For
example, on DM365, queue 0 has large fifo size and is more suitable
for video transfers. Having audio and video transfers on the same
queue may lead to starvation on audio side.
platform data as defined currently passes a queue number to the driver
but that remains unused inside the driver.
Fix this by defining one queue each for ASP and RAM transfers in the
platform data and using it inside the driver.
Since EDMAQ_0 maps to 0, thats the queue that will be used if
the asp queue number is not initialized. None of the platforms
currently utilize ping-pong transfers through internal RAM so that
functionality remains unchanged too.
This patch has been tested on DM644x and OMAP-L138 EVMs.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The touch screen controller in the TPS6507x chip needs values that are
dependent on the characteristics of the touch screen hardware being used
in the board design. In addition, the board provides version information
that is exposed via the kernel input sub-system.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add mfd structure which refrences sub-driver initialization data. For example,
for a giving hardware implementation, the voltage regulator sub-driver
initialization data provides the mapping betten a voltage regulator and what
the output voltage is being used for.
Signed-off-by: Todd Fischer <todd.fischer@ridgerun.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch implements the following:
- interrupt initialization uses ioremap() instead of passing a virtual address
via davinci_soc_info.
- machine definitions directly point to cp_intc_init() or davinci_irq_init()
- davinci_intc_type and davinci_intc_base now get initialized in controller
specific init functions instead of davinci_common_init()
- minor fix in davinci_irq_init() to use intc_irq_num instead of
DAVINCI_N_AINTC_IRQ
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Rename da8xx_pinmux_setup() to davinci_cfg_reg_list() and promote it for use in
other SOCs that may need the ability to configure multiple pins in one shot.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Host map configuration instructs the interrupt controller to route interrupt
channels to FIQ or IRQ lines. Currently, DA8xx family of devices leave these
registers at their reset-default values.
TNETV107X however does not have sane reset defaults, and therefore this
architecture needs to reconfigure the host-map such that channels 0 and 1
go to FIQ, and the remaining channels raise IRQs.
This patch adds an optional host map argument to cp_intc_init() for this.
Signed-off-by: Cyril Chemparathy <cyril@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch initializes the platform data to enable 4-bit
ecc support on DA850/OMAP-L138.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On DA850/OMAP-L138, NOR flash partition was starting from offset
ZERO erasing the UBL and u-boot when the complete NOR is erased.
This patch moves the start of the partition to 512K, after the
bootloaders and u-boot env variables.
This patch also creates a new partition on NOR Flash to store
Linux kernel image.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP-L138 adds a second SYSCFG region having useful functionality
like deep sleep, pull up/down control and SATA clock stop.
This patch makes provision for accessing registers from second
SYSCFG region in da8xx code.
Note that OMAP-L137 has a single SYSCFG region.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add the platform specific callback to control LCD panel and backlight
power.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include high speed capabilities in MMC/SD platform data
for DA830/OMAP-L137 and DA850/OMAP-L138 EVMs.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When kernel is built with CONFIG_DEBUG_SECTION_MISMATCH=y
option, using da8xx_omapl_defconfig, some warnings are
observed:
WARNING: vmlinux.o(.text+0xc2a4): Section mismatch in reference
from the function da850_evm_setup_nor_nand() to the variable
.init.data:da850_nand_pins
The function da850_evm_setup_nor_nand() references
the variable __initdata da850_nand_pins.
This is often because da850_evm_setup_nor_nand lacks a __initdata
annotation or the annotation of da850_nand_pins is wrong.
This patch fixes such warnings.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Eliminate the static function declaration by rearranging
data in da850/omap-l138 board file.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There are multiple steps in configuring the EMAC to MII or RMII mode.
Current code implements them using multiple checks.
Consolidate the multiple checks into a single if construct.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Implement autodetection of RMII PHY by shifting the decision
to use the RMII PHY to da850_evm_ui_expander_setup() from
da850_evm_init() earlier.
Without this patch, selecting RMII PHY in the UI expander menu
will make the MII PHY unusable even though UI board is not
connected.
The actual configuration and registration of the EMAC device
is delayed to device_initcall() so it happens after the UI card
detection is complete.
A side effect of this patch is the removal of a voilation of
Documentation/SubmittingPatches section 2.2 in function
da850_evm_init()
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There have accumulated quite a lot of them after the code reorganizations...
In several cases I had to replace #include <linux/dma-mapping.h> which wasn't
needed directly but happened to #include <linux/err.h> which was needed.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DA850/OMAP-L138 EVM has a RMII Ethernet PHY on the UI daughter card. The PHY
is enabled by proper programming of the IO Expander (TCA6416) ports. Also for
RMII PHY to work, the MDIO clock of MII PHY has to be disabled since both the
PHYs have the same address. This is done via the GPIO2[6] pin. This patch adds
support for RMII PHY.
This patch also adds a menuconfig option to select one or no peripheral
connected to expander. Currently, sub-options in this menu are RMII and no
peripheral.This menuconfig option is similar to the one present for UI card on
DA830/OMAP-L137 EVM.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
DA850/OMAP-L138 EVM can be connected to an UI card which has various
peripherals on it.The UI card has TCA6416 expander which can be probed
to check whether the UI card is connected or not. If the UI card is
connected, setup NOR and NAND devices. This is done via the expander
setup callback.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds support for using the TPS65070 PMIC found
on the DA850/OMAP-L138 EVM.
It defines the power rail consumer mapping and registers the
the I2C based PMIC as a board device.
The power rail constraints are derived from the maxmimum and
minimum recommended operating condition values of the respective
consumers derived from section 5.2 of the OMAP-L138 datasheet.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On the latest DA850/OMAP-L138 EVM (Beta) the GPIO pin
number of LCD panel power has changed. This patch takes
care of this change. Software will support only Beta
versions of DA850/OMAP-L138 EVM.
In the process, add the missing entry for data pin 0
and remove the GPIO specific pins from da850_lcdcntl_pins
structure. EVM specific muxing for LCD is being done in the
board file now.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add RTC support for the da830/omap-l137 and da850/omap-l138
SoC's by leveraging existing the rtc-omap driver.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for the Sharp LCD035Q3DG01 graphical LCD. This
requires a minor interface change to da8xx_register_lcdc()
so that the board code can pass in the platform_data which
describes the lcd controller that's to be used.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
For consistency with existing code, change the name of
da8xx_init_mcasp() to da8xx_register_mcasp().
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested on DM6446, DM355, DM6447, DA850 EVMs.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
On DA850/OMAP-L138 EVM, MMC/SD and NOR Flash share
some of the AEMIF pins. This patch prints out a warning
during booting, if both MMC/SD and NOR Flash are enabled
in kernel menuconfig.
If both MMC/SD and NOR Flash are enabled, only MMC/SD
will work correctly.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform data for the 8MB NOR flash
found on da850/omap-l138 EVM. Both NOR and NAND can
co-exist on da850/omap-l138 as they are using different
chip selects.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform data for the 512MB NAND Flash
found on DA850/OMAP-L138 EVM. Currently it supports
only 1-bit ECC.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
There are two instances of MMC/SD on da850/omap-l138.
Connector for the first instance is available on the
EVM. This patch adds support for this instance.
This patch also adds support for card detect and write
protect switches on da850/omap-l138 EVM.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds platform support for the graphic display
(Sharp LK043T1DG01) found on DA850/OMAP-L138 based EVM.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Define resources for McASP used on DA850/OMAP-L138 EVM, add platform
device defintion and Pin Mux configurations.
Signed-off-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Ethernet Media Access Controller (EMAC) on da850/omap-l138
supports 10/100 Mbps operation. It also supports Media
Independent Interface (MII) and Reduced Media Independent
Interface (RMII) to physical layer (PHY).
Phy which supports MII is present on the DA850/OMAP-L138
base board and Phy supporting RMII is present on the
UI card. This patch adds support only for the MII Phy.
Support for RMII Phy will be added later.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add support for the DA850/OMAP-L138 Evaluation Module (EVM)
from TI. The EVM has User Interface (UI) card which contains
various devices. This UI card can be connected to the base
board. Support for all the devices on the UI card and ones on
the EVM will be added in subsequent patches.
The EVM schematics are not available publicly yet; but should
be available soon.
A new defconfig for this board has been added mainly because
the DA830/OMAP-L137 defconfig forces writethrough cache mode
which is not required on DA850/OMAP-L138.
This patch has been boot tested on DA850/OMAP-L138 EVM
using ramdisk as filesystem.
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Sergei Shtylyov