This patch fixes TX hangs with threaded NAPI enabled. The scheduled
NAPI seems to be executed in parallel with the interrupt on second
thread. Sometimes it happens that ltq_dma_disable_irq() is executed
after xrx200_tx_housekeeping(). The symptom is that TX interrupts
are disabled in the DMA controller. As a result, the TX hangs after
a few seconds of the iperf test. Scheduling NAPI after disabling
interrupts fixes this issue.
Tested on Lantiq xRX200 (BT Home Hub 5A).
Fixes: 9423361da5 ("net: lantiq: Disable IRQs only if NAPI gets scheduled ")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes several bugs found when (DMA/LLQ) mapping a packet for
transmission. The mapping procedure makes the transmitted packet
accessible by the device.
When using LLQ, this requires copying the packet's header to push header
(which would be passed to LLQ) and creating DMA mapping for the payload
(if the packet doesn't fit the maximum push length).
When not using LLQ, we map the whole packet with DMA.
The following bugs are fixed in the code:
1. Add support for non-LLQ machines:
The ena_xdp_tx_map_frame() function assumed that LLQ is
supported, and never mapped the whole packet using DMA. On some
instances, which don't support LLQ, this causes loss of traffic.
2. Wrong DMA buffer length passed to device:
When using LLQ, the first 'tx_max_header_size' bytes of the
packet would be copied to push header. The rest of the packet
would be copied to a DMA'd buffer.
3. Freeing the XDP buffer twice in case of a mapping error:
In case a buffer DMA mapping fails, the function uses
xdp_return_frame_rx_napi() to free the RX buffer and returns from
the function with an error. XDP frames that fail to xmit get
freed by the kernel and so there is no need for this call.
Fixes: 548c4940b9 ("net: ena: Implement XDP_TX action")
Signed-off-by: Shay Agroskin <shayagr@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because flow control is set up statically in ocelot_init_port(), and not
in phylink_mac_link_up(), what happens is that after the blamed commit,
the flow control remains disabled after the port flushing procedure.
Fixes: eb4733d7cf ("net: dsa: felix: implement port flushing on .phylink_mac_link_down")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thermal polling delay argument for modules and gearboxes thermal zones
used to be initialized with zero value, while actual delay was used to
be set by mlxsw_thermal_set_mode() by thermal operation callback
set_mode(). After operations set_mode()/get_mode() have been removed by
cited commits, modules and gearboxes thermal zones always have polling
time set to zero and do not perform temperature monitoring.
Set non-zero "polling_delay" in thermal_zone_device_register() routine,
thus, the relevant thermal zones will perform thermal monitoring.
Cc: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Fixes: 5d7bd8aa7c ("thermal: Simplify or eliminate unnecessary set_mode() methods")
Fixes: 1ee14820fd ("thermal: remove get_mode() operation of drivers")
Signed-off-by: Mykola Kostenok <c_mykolak@nvidia.com>
Acked-by: Vadim Pasternak <vadimp@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mlxsw Qdisc offload, find_class() is an operation that yields a qdisc
offload descriptor given a parental qdisc descriptor and a class handle. In
__mlxsw_sp_qdisc_ets_graft() however, a band number is passed to that
function instead of a handle. This can lead to a trigger of a WARN_ON
with the following splat:
WARNING: CPU: 3 PID: 808 at drivers/net/ethernet/mellanox/mlxsw/spectrum_qdisc.c:1356 __mlxsw_sp_qdisc_ets_graft+0x115/0x130 [mlxsw_spectrum]
[...]
Call Trace:
mlxsw_sp_setup_tc_prio+0xe3/0x100 [mlxsw_spectrum]
qdisc_offload_graft_helper+0x35/0xa0
prio_graft+0x176/0x290 [sch_prio]
qdisc_graft+0xb3/0x540
tc_modify_qdisc+0x56a/0x8a0
rtnetlink_rcv_msg+0x12c/0x370
netlink_rcv_skb+0x49/0xf0
netlink_unicast+0x1f6/0x2b0
netlink_sendmsg+0x1fb/0x410
____sys_sendmsg+0x1f3/0x220
___sys_sendmsg+0x70/0xb0
__sys_sendmsg+0x54/0xa0
do_syscall_64+0x3a/0x70
entry_SYSCALL_64_after_hwframe+0x44/0xae
Since the parent handle is not passed with the offload information, compute
it from the band number and qdisc handle.
Fixes: 28052e618b04 ("mlxsw: spectrum_qdisc: Track children per qdisc")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A max-shaper is the HW component responsible for delaying egress traffic
above a configured transmission rate. Burst size is the amount of traffic
that is allowed to pass without accounting. The burst size value needs to
be such that it can be expressed as 2^BS * 512 bits, where BS lies in a
certain ASIC-dependent range. mlxsw enforces that this holds before
attempting to configure the shaper.
The assumption for Spectrum-3 was that the lower limit of BS would be 5,
like for Spectrum-1. But as of now, the limit is still 11. Therefore fix
the driver accordingly, so that incorrect values are rejected early with a
proper message.
Fixes: 23effa2479 ("mlxsw: reg: Add max_shaper_bs to QoS ETS Element Configuration")
Reported-by: Maksym Yaremchuk <maksymy@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring TC-MQPRIO offload, only turn off netdev carrier and
don't bring physical link down in hardware. Otherwise, when the
physical link is brought up again after configuration, it gets
re-trained and stalls ongoing traffic.
Also, when firmware is no longer accessible or crashed, avoid sending
FLOWC and waiting for reply that will never come.
Fix following hung_task_timeout_secs trace seen in these cases.
INFO: task tc:20807 blocked for more than 122 seconds.
Tainted: G S 5.13.0-rc3+ #122
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
task:tc state:D stack:14768 pid:20807 ppid: 19366 flags:0x00000000
Call Trace:
__schedule+0x27b/0x6a0
schedule+0x37/0xa0
schedule_preempt_disabled+0x5/0x10
__mutex_lock.isra.14+0x2a0/0x4a0
? netlink_lookup+0x120/0x1a0
? rtnl_fill_ifinfo+0x10f0/0x10f0
__netlink_dump_start+0x70/0x250
rtnetlink_rcv_msg+0x28b/0x380
? rtnl_fill_ifinfo+0x10f0/0x10f0
? rtnl_calcit.isra.42+0x120/0x120
netlink_rcv_skb+0x4b/0xf0
netlink_unicast+0x1a0/0x280
netlink_sendmsg+0x216/0x440
sock_sendmsg+0x56/0x60
__sys_sendto+0xe9/0x150
? handle_mm_fault+0x6d/0x1b0
? do_user_addr_fault+0x1c5/0x620
__x64_sys_sendto+0x1f/0x30
do_syscall_64+0x3c/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f7f73218321
RSP: 002b:00007ffd19626208 EFLAGS: 00000246 ORIG_RAX: 000000000000002c
RAX: ffffffffffffffda RBX: 000055b7c0a8b240 RCX: 00007f7f73218321
RDX: 0000000000000028 RSI: 00007ffd19626210 RDI: 0000000000000003
RBP: 000055b7c08680ff R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 000055b7c085f5f6
R13: 000055b7c085f60a R14: 00007ffd19636470 R15: 00007ffd196262a0
Fixes: b1396c2bd6 ("cxgb4: parse and configure TC-MQPRIO offload")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently in the ice driver, the check whether to
allow a LLDP packet to egress the interface from the
PF_VSI is being based on the SKB's priority field.
It checks to see if the packets priority is equal to
TC_PRIO_CONTROL. Injected LLDP packets do not always
meet this condition.
SCAPY defaults to a sk_buff->protocol value of ETH_P_ALL
(0x0003) and does not set the priority field. There will
be other injection methods (even ones used by end users)
that will not correctly configure the socket so that
SKB fields are correctly populated.
Then ethernet header has to have to correct value for
the protocol though.
Add a check to also allow packets whose ethhdr->h_proto
matches ETH_P_LLDP (0x88CC).
Fixes: 0c3a6101ff ("ice: Allow egress control packets from PF_VSI")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ethtool incorrectly reported supported and advertised auto-negotiation
settings for a backplane PHY image which did not support auto-negotiation.
This can occur when using media or PHY type for reporting ethtool
supported and advertised auto-negotiation settings.
Remove setting supported and advertised auto-negotiation settings based
on PHY type in ice_phy_type_to_ethtool(), and MAC type in
ice_get_link_ksettings().
Ethtool supported and advertised auto-negotiation settings should be
based on the PHY image using the AQ command get PHY capabilities with
media. Add setting supported and advertised auto-negotiation settings
based get PHY capabilities with media in ice_get_link_ksettings().
Fixes: 48cb27f2fd ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
VSI rebuild can be failed for LAN queue config, then the VF's VSI will
be NULL, the VF reset should be stopped with the VF entering into the
disable state.
Fixes: 12bb018c53 ("ice: Refactor VF reset")
Signed-off-by: Haiyue Wang <haiyue.wang@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Some AVF drivers expect the VF_MBX_ATQLEN register to be cleared for any
type of VFR/VFLR. Fix this by clearing the VF_MBX_ATQLEN register at the
same time as VF_MBX_ARQLEN.
Fixes: 82ba01282c ("ice: clear VF ARQLEN register on reset")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 12bb018c53 ("ice: Refactor VF reset") caused a regression
that removes the ability for a VF to request a different amount of
queues via VIRTCHNL_OP_REQUEST_QUEUES. This prevents VF drivers to
either increase or decrease the number of queue pairs they are
allocated. Fix this by using the variable vf->num_req_qs when
determining the vf->num_vf_qs during VF VSI creation.
Fixes: 12bb018c53 ("ice: Refactor VF reset")
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
commit db43b30cd8 ("cxgb4: add ethtool n-tuple filter deletion")
has moved searching for next highest priority HASH filter rule to
cxgb4_flow_rule_destroy(), which searches the rhashtable before the
the rule is removed from it and hence always finds at least 1 entry.
Fix by removing the rule from rhashtable first before calling
cxgb4_flow_rule_destroy() and hence avoid fetching stale info.
Fixes: db43b30cd8 ("cxgb4: add ethtool n-tuple filter deletion")
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit c7a219048e ("ice: Remove xsk_buff_pool from VSI structure")
silently introduced a regression and broke the Tx side of AF_XDP in copy
mode. xsk_pool on ice_ring is set only based on the existence of the XDP
prog on the VSI which in turn picks ice_clean_tx_irq_zc to be executed.
That is not something that should happen for copy mode as it should use
the regular data path ice_clean_tx_irq.
This results in a following splat when xdpsock is run in txonly or l2fwd
scenarios in copy mode:
<snip>
[ 106.050195] BUG: kernel NULL pointer dereference, address: 0000000000000030
[ 106.057269] #PF: supervisor read access in kernel mode
[ 106.062493] #PF: error_code(0x0000) - not-present page
[ 106.067709] PGD 0 P4D 0
[ 106.070293] Oops: 0000 [#1] PREEMPT SMP NOPTI
[ 106.074721] CPU: 61 PID: 0 Comm: swapper/61 Not tainted 5.12.0-rc2+ #45
[ 106.081436] Hardware name: Intel Corporation S2600WFT/S2600WFT, BIOS SE5C620.86B.02.01.0008.031920191559 03/19/2019
[ 106.092027] RIP: 0010:xp_raw_get_dma+0x36/0x50
[ 106.096551] Code: 74 14 48 b8 ff ff ff ff ff ff 00 00 48 21 f0 48 c1 ee 30 48 01 c6 48 8b 87 90 00 00 00 48 89 f2 81 e6 ff 0f 00 00 48 c1 ea 0c <48> 8b 04 d0 48 83 e0 fe 48 01 f0 c3 66 66 2e 0f 1f 84 00 00 00 00
[ 106.115588] RSP: 0018:ffffc9000d694e50 EFLAGS: 00010206
[ 106.120893] RAX: 0000000000000000 RBX: ffff88984b8c8a00 RCX: ffff889852581800
[ 106.128137] RDX: 0000000000000006 RSI: 0000000000000000 RDI: ffff88984cd8b800
[ 106.135383] RBP: ffff888123b50001 R08: ffff889896800000 R09: 0000000000000800
[ 106.142628] R10: 0000000000000000 R11: ffffffff826060c0 R12: 00000000000000ff
[ 106.149872] R13: 0000000000000000 R14: 0000000000000040 R15: ffff888123b50018
[ 106.157117] FS: 0000000000000000(0000) GS:ffff8897e0f40000(0000) knlGS:0000000000000000
[ 106.165332] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 106.171163] CR2: 0000000000000030 CR3: 000000000560a004 CR4: 00000000007706e0
[ 106.178408] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 106.185653] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 106.192898] PKRU: 55555554
[ 106.195653] Call Trace:
[ 106.198143] <IRQ>
[ 106.200196] ice_clean_tx_irq_zc+0x183/0x2a0 [ice]
[ 106.205087] ice_napi_poll+0x3e/0x590 [ice]
[ 106.209356] __napi_poll+0x2a/0x160
[ 106.212911] net_rx_action+0xd6/0x200
[ 106.216634] __do_softirq+0xbf/0x29b
[ 106.220274] irq_exit_rcu+0x88/0xc0
[ 106.223819] common_interrupt+0x7b/0xa0
[ 106.227719] </IRQ>
[ 106.229857] asm_common_interrupt+0x1e/0x40
</snip>
Fix this by introducing the bitmap of queues that are zero-copy enabled,
where each bit, corresponding to a queue id that xsk pool is being
configured on, will be set/cleared within ice_xsk_pool_{en,dis}able and
checked within ice_xsk_pool(). The latter is a function used for
deciding which napi poll routine is executed.
Idea is being taken from our other drivers such as i40e and ixgbe.
Fixes: c7a219048e ("ice: Remove xsk_buff_pool from VSI structure")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.
Fixes: 73f1071c1d ("igc: Add support for XDP_TX action")
Fixes: 4ff3203610 ("igc: Add support for XDP_REDIRECT action")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Dvora Fuxbrumer <dvorax.fuxbrumer@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.
Fixes: 21092e9ce8 ("ixgbevf: Add support for XDP_TX action")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.
Fixes: 9cbc948b5a ("igb: add XDP support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.
Fixes: 33fdc82f08 ("ixgbe: add support for XDP_TX action")
Fixes: d0bcacd0a1 ("ixgbe: add AF_XDP zero-copy Rx support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Vishakha Jambekar <vishakha.jambekar@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add missing exception tracing to XDP when a number of different
errors can occur. The support was only partial. Several errors
where not logged which would confuse the user quite a lot not
knowing where and why the packets disappeared.
Fixes: efc2214b60 ("ice: Add support for XDP")
Fixes: 2d4238f556 ("ice: Add support for AF_XDP")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add missing exception tracing to XDP when a number of different errors
can occur. The support was only partial. Several errors where not
logged which would confuse the user quite a lot not knowing where and
why the packets disappeared.
Fixes: 74608d17fe ("i40e: add support for XDP_TX action")
Fixes: 0a714186d3 ("i40e: add AF_XDP zero-copy Rx support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Kiran Bhandare <kiranx.bhandare@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When using native XDP with the igb driver, the XDP frame data doesn't point to
the beginning of the packet. It's off by 16 bytes. Everything works as expected
with XDP skb mode.
Actually these 16 bytes are used to store the packet timestamps. Therefore, pull
the timestamp before executing any XDP operations and adjust all other code
accordingly. The igc driver does it like that as well.
Tested with Intel i210 card and AF_XDP sockets.
Fixes: 9cbc948b5a ("igb: add XDP support")
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Flow table that contains flow pointing to multiple flow tables or multiple
TIRs must have a level lower than 64. In our case it applies to muli-
destination flow table.
Fix the level of the created table to comply with HW Spec definitions, and
still make sure that its level lower than SW-owned tables, so that it
would be possible to point from the multi-destination FW table to SW
tables.
Fixes: 34583beea4 ("net/mlx5: DR, Create multi-destination table for SW-steering use")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
When a driver's profile doesn't support a dedicated PTP-RQ,
configuration of CQE compression while HW TS is configured should fail.
Fixes: 885b8cfb16 ("net/mlx5e: Update ethtool setting of CQE compression")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
On some devices the ignore flow level cap is not supported and we
shouldn't use it. Setting the dest ft with mlx5_chains_get_tc_end_ft()
already gives the correct end ft if ignore flow level cap is supported
or not.
Fixes: 39ac237ce0 ("net/mlx5: E-Switch, Refactor chains and priorities")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
If not supported show an error and return instead of trying to offload
to the hardware and fail.
Fixes: 699e96ddf4 ("net/mlx5e: Support offloading tc double vlan headers match")
Reported-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
In case driver sent NACK to firmware on sync reset request, it will get
sync reset abort event while it didn't set sync reset requested mode.
Thus, on abort sync reset event handler, driver should check reset
requested is set before trying to stop sync reset poll.
Fixes: 7dd6df329d ("net/mlx5: Handle sync reset abort event")
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
TLS offload is not supported in switchdev mode.
Fixes: 7a9fb35e8c ("net/mlx5e: Do not reload ethernet ports when changing eswitch mode")
Signed-off-by: Roi Dayan <roid@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Device supports setting of a single fec mode at a time, enforce this
by bitmap_weight == 1. Input from fec command is in u32, avoid cast to
unsigned long and use bitmap_from_arr32 to populate bitmap safely.
Fixes: 4bd9d5070b ("net/mlx5e: Enforce setting of a single FEC mode")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
The error code is missing in this code scenario, add the error code
'-EINVAL' to the return value 'status'.
Eliminate the follow smatch warning:
drivers/net/ethernet/myricom/myri10ge/myri10ge.c:3818 myri10ge_probe()
warn: missing error code 'status'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed link does not need mdio bus and in that case mdio_bus_data will
not be allocated. Before using mdio_bus_data we should check for NULL.
This patch fix the kernel panic due to NULL pointer dereference of
mdio_bus_data when it is not allocated.
Without this patch we do see following kernel crash caused due to kernel
NULL pointer dereference.
Call trace:
stmmac_dvr_probe+0x3c/0x10b0
dwc_eth_dwmac_probe+0x224/0x378
platform_probe+0x68/0xe0
really_probe+0x130/0x3d8
driver_probe_device+0x68/0xd0
device_driver_attach+0x74/0x80
__driver_attach+0x58/0xf8
bus_for_each_dev+0x7c/0xd8
driver_attach+0x24/0x30
bus_add_driver+0x148/0x1f0
driver_register+0x64/0x120
__platform_driver_register+0x28/0x38
dwc_eth_dwmac_driver_init+0x1c/0x28
do_one_initcall+0x78/0x158
kernel_init_freeable+0x1f0/0x244
kernel_init+0x14/0x118
ret_from_fork+0x10/0x30
Code: f9002bfb 9113e2d9 910e6273 aa0003f7 (f9405c78)
---[ end trace 32d9d41562ddc081 ]---
Fixes: e5e5b771f6 ("net: stmmac: make in-band AN mode parsing is supported for non-DT")
Signed-off-by: Sriranjani P <sriranjani.p@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Link: https://lore.kernel.org/r/20210528071056.35252-1-sriranjani.p@samsung.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
can and wireless trees. Notably including fixes for the recently
announced "FragAttacks" WiFi vulnerabilities. Rather large batch,
touching some core parts of the stack, too, but nothing hair-raising.
Current release - regressions:
- tipc: make node link identity publish thread safe
- dsa: felix: re-enable TAS guard band mode
- stmmac: correct clocks enabled in stmmac_vlan_rx_kill_vid()
- stmmac: fix system hang if change mac address after interface ifdown
Current release - new code bugs:
- mptcp: avoid OOB access in setsockopt()
- bpf: Fix nested bpf_bprintf_prepare with more per-cpu buffers
- ethtool: stats: fix a copy-paste error - init correct array size
Previous releases - regressions:
- sched: fix packet stuck problem for lockless qdisc
- net: really orphan skbs tied to closing sk
- mlx4: fix EEPROM dump support
- bpf: fix alu32 const subreg bound tracking on bitwise operations
- bpf: fix mask direction swap upon off reg sign change
- bpf, offload: reorder offload callback 'prepare' in verifier
- stmmac: Fix MAC WoL not working if PHY does not support WoL
- packetmmap: fix only tx timestamp on request
- tipc: skb_linearize the head skb when reassembling msgs
Previous releases - always broken:
- mac80211: address recent "FragAttacks" vulnerabilities
- mac80211: do not accept/forward invalid EAPOL frames
- mptcp: avoid potential error message floods
- bpf, ringbuf: deny reserve of buffers larger than ringbuf to prevent
out of buffer writes
- bpf: forbid trampoline attach for functions with variable arguments
- bpf: add deny list of functions to prevent inf recursion of tracing
programs
- tls splice: check SPLICE_F_NONBLOCK instead of MSG_DONTWAIT
- can: isotp: prevent race between isotp_bind() and isotp_setsockopt()
- netfilter: nft_set_pipapo_avx2: Add irq_fpu_usable() check,
fallback to non-AVX2 version
Misc:
- bpf: add kconfig knob for disabling unpriv bpf by default
-----BEGIN PGP SIGNATURE-----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=peMK
-----END PGP SIGNATURE-----
Merge tag 'net-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Networking fixes for 5.13-rc4, including fixes from bpf, netfilter,
can and wireless trees. Notably including fixes for the recently
announced "FragAttacks" WiFi vulnerabilities. Rather large batch,
touching some core parts of the stack, too, but nothing hair-raising.
Current release - regressions:
- tipc: make node link identity publish thread safe
- dsa: felix: re-enable TAS guard band mode
- stmmac: correct clocks enabled in stmmac_vlan_rx_kill_vid()
- stmmac: fix system hang if change mac address after interface
ifdown
Current release - new code bugs:
- mptcp: avoid OOB access in setsockopt()
- bpf: Fix nested bpf_bprintf_prepare with more per-cpu buffers
- ethtool: stats: fix a copy-paste error - init correct array size
Previous releases - regressions:
- sched: fix packet stuck problem for lockless qdisc
- net: really orphan skbs tied to closing sk
- mlx4: fix EEPROM dump support
- bpf: fix alu32 const subreg bound tracking on bitwise operations
- bpf: fix mask direction swap upon off reg sign change
- bpf, offload: reorder offload callback 'prepare' in verifier
- stmmac: Fix MAC WoL not working if PHY does not support WoL
- packetmmap: fix only tx timestamp on request
- tipc: skb_linearize the head skb when reassembling msgs
Previous releases - always broken:
- mac80211: address recent "FragAttacks" vulnerabilities
- mac80211: do not accept/forward invalid EAPOL frames
- mptcp: avoid potential error message floods
- bpf, ringbuf: deny reserve of buffers larger than ringbuf to
prevent out of buffer writes
- bpf: forbid trampoline attach for functions with variable arguments
- bpf: add deny list of functions to prevent inf recursion of tracing
programs
- tls splice: check SPLICE_F_NONBLOCK instead of MSG_DONTWAIT
- can: isotp: prevent race between isotp_bind() and
isotp_setsockopt()
- netfilter: nft_set_pipapo_avx2: Add irq_fpu_usable() check,
fallback to non-AVX2 version
Misc:
- bpf: add kconfig knob for disabling unpriv bpf by default"
* tag 'net-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (172 commits)
net: phy: Document phydev::dev_flags bits allocation
mptcp: validate 'id' when stopping the ADD_ADDR retransmit timer
mptcp: avoid error message on infinite mapping
mptcp: drop unconditional pr_warn on bad opt
mptcp: avoid OOB access in setsockopt()
nfp: update maintainer and mailing list addresses
net: mvpp2: add buffer header handling in RX
bnx2x: Fix missing error code in bnx2x_iov_init_one()
net: zero-initialize tc skb extension on allocation
net: hns: Fix kernel-doc
sctp: fix the proc_handler for sysctl encap_port
sctp: add the missing setting for asoc encap_port
bpf, selftests: Adjust few selftest result_unpriv outcomes
bpf: No need to simulate speculative domain for immediates
bpf: Fix mask direction swap upon off reg sign change
bpf: Wrap aux data inside bpf_sanitize_info container
bpf: Fix BPF_LSM kconfig symbol dependency
selftests/bpf: Add test for l3 use of bpf_redirect_peer
bpftool: Add sock_release help info for cgroup attach/prog load command
net: dsa: microchip: enable phy errata workaround on 9567
...
If Link Partner sends frames larger than RX buffer size, MAC mark it
as oversize but still would pass it to the Packet Processor.
In this scenario, Packet Processor scatter frame between multiple buffers,
but only a single buffer would be returned to the Buffer Manager pool and
it would not refill the poll.
Patch add handling of oversize error with buffer header handling, so all
buffers would be returned to the Buffer Manager pool.
Fixes: 3f518509de ("ethernet: Add new driver for Marvell Armada 375 network unit")
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix function name in hns_ethtool.c kernel-doc comment
to remove these warnings found by clang_w1.
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:202: warning: expecting
prototype for hns_nic_set_link_settings(). Prototype was for
hns_nic_set_link_ksettings() instead.
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:837: warning: expecting
prototype for get_ethtool_stats(). Prototype was for
hns_get_ethtool_stats() instead.
drivers/net/ethernet/hisilicon/hns/hns_ethtool.c:894: warning:
expecting prototype for get_strings(). Prototype was for
hns_get_strings() instead.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 'commit 262b38cdb3 ("net: ethernet: hisilicon: hns: use phydev
from struct net_device")'
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If runtime power menagement is enabled, the gigabit ethernet PLL would
be disabled after macb_probe(). During this period of time, the system
would hang up if we try to access GEMGXL control registers.
We can't put runtime_pm_get/runtime_pm_put/ there due to the issue of
sleep inside atomic section (7fa2955ff7 ("sh_eth: Fix sleeping
function called from invalid context"). Add netif_running checking to
ensure the device is available before accessing GEMGXL device.
Changed in v2:
- Use netif_running instead of its own flag
Signed-off-by: Zong Li <zong.li@sifive.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MT7628/88 SoC(s) have other (limited) packet counter registers than
currently supported in the mtk_eth_soc driver. This patch adds support
for reading these registers, so that the packet statistics are correctly
updated.
Additionally the defines for the non-MT7628 variant packet counter
registers are added and used in this patch instead of using hard coded
values.
Signed-off-by: Stefan Roese <sr@denx.de>
Fixes: 296c912075 ("net: ethernet: mediatek: Add MT7628/88 SoC support")
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Reto Schneider <code@reto-schneider.ch>
Cc: Reto Schneider <reto.schneider@husqvarnagroup.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
SFC driver can be configured via modparam to work using MSI-X, MSI or
legacy IRQ interrupts. In the last one, the interrupt was not properly
released on module remove.
It was not freed because the flag irqs_hooked was not set during
initialization in the case of using legacy IRQ.
Example of (trimmed) trace during module remove without this fix:
remove_proc_entry: removing non-empty directory 'irq/125', leaking at least '0000:3b:00.1'
WARNING: CPU: 39 PID: 3658 at fs/proc/generic.c:715 remove_proc_entry+0x15c/0x170
...trimmed...
Call Trace:
unregister_irq_proc+0xe3/0x100
free_desc+0x29/0x70
irq_free_descs+0x47/0x70
mp_unmap_irq+0x58/0x60
acpi_unregister_gsi_ioapic+0x2a/0x40
acpi_pci_irq_disable+0x78/0xb0
pci_disable_device+0xd1/0x100
efx_pci_remove+0xa1/0x1e0 [sfc]
pci_device_remove+0x38/0xa0
__device_release_driver+0x177/0x230
driver_detach+0xcb/0x110
bus_remove_driver+0x58/0xd0
pci_unregister_driver+0x2a/0xb0
efx_exit_module+0x24/0xf40 [sfc]
__do_sys_delete_module.constprop.0+0x171/0x280
? exit_to_user_mode_prepare+0x83/0x1d0
do_syscall_64+0x3d/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7f9f9385800b
...trimmed...
Signed-off-by: Íñigo Huguet <ihuguet@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a situation where memory allocation or dma mapping fails, an
invalid address is programmed into the descriptor. This can lead
to memory corruption. If the memory allocation fails, DMA should
reuse the previous skb and mapping and drop the packet. This patch
also increments rx drop counter.
Fixes: fe1a56420c ("net: lantiq: Add Lantiq / Intel VRX200 Ethernet driver ")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
When updating to latest mainline for some testing on the GARDENA smart
gateway based on the MT7628, I noticed that ethernet does not work any
more. Commit e9229ffd55 ("net: ethernet: mtk_eth_soc: implement
dynamic interrupt moderation") introduced this problem, as it missed the
RX_DIM & TX_DIM configuration for this SoC variant. This patch fixes
this by calling mtk_dim_rx() & mtk_dim_tx() in this case as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Fixes: e9229ffd55 ("net: ethernet: mtk_eth_soc: implement dynamic interrupt moderation")
Cc: Felix Fietkau <nbd@nbd.name>
Cc: John Crispin <john@phrozen.org>
Cc: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Reto Schneider <code@reto-schneider.ch>
Cc: Reto Schneider <reto.schneider@husqvarnagroup.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix system hang with below sequences:
~# ifconfig ethx down
~# ifconfig ethx hw ether xx:xx:xx:xx:xx:xx
After ethx down, stmmac all clocks gated off and then register access causes
system hang.
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This should be a mistake to fix conflicts when removing RFC tag to
repost the patch.
Fixes: 5ec5582343 ("net: stmmac: add clocks management for gmac driver")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The opening comment mark '/**' is used for highlighting the beginning of
kernel-doc comments.
The header for drivers/net/ethernet/microchip/encx24j600 files follows
this syntax, but the content inside does not comply with kernel-doc.
This line was probably not meant for kernel-doc parsing, but is parsed
due to the presence of kernel-doc like comment syntax(i.e, '/**'), which
causes unexpected warning from kernel-doc.
For e.g., running scripts/kernel-doc -none
drivers/net/ethernet/microchip/encx24j600_hw.h emits:
warning: expecting prototype for h(). Prototype was for _ENCX24J600_HW_H() instead
Provide a simple fix by replacing such occurrences with general comment
format, i.e. '/*', to prevent kernel-doc from parsing it.
Signed-off-by: Aditya Srivastava <yashsri421@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that the MTU value requested by the VF is in the supported
range of MTUs before attempting to set the VF large packet enable,
otherwise reject the request. This also avoids unnecessary
register updates in the case of the 82599 controller.
Fixes: 872844ddb9 ("ixgbe: Enable jumbo frames support w/ SR-IOV")
Co-developed-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Piotr Skajewski <piotrx.skajewski@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hardware register having the server TID base can contain
invalid values when adapter is in bad state (for example,
due to AER fatal error). Reading these invalid values in the
register can lead to out-of-bound memory access. So, fix
by using the saved server TID base when clearing filters.
Fixes: b1a79360ee ("cxgb4: Delete all hash and TCAM filters before resource cleanup")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not correct to call napi_schedule() in pure process
context. Because we use __raise_softirq_irqoff() we require
callers to be in a context which will eventually lead to
softirq handling (hardirq, bh disabled, etc.).
With code as is users will see:
NOHZ tick-stop error: Non-RCU local softirq work is pending, handler #08!!!
Fixes: a8dd7ac12f ("net/mlx5e: Generalize RQ activation")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Termination tables are restricted to have the default miss action and
cannot be set to forward to another table in case of a miss.
If the fs prio of the termination table is not the last one in the
list, fs_core will attempt to attach it to another table.
Set the unmanaged ft flag when creating the termination table ft
and select the tc offload prio for it to prevent fs_core from selecting
the forwarding to next ft miss action and use the default one.
In addition, set the flow that forwards to the termination table to
ignore ft level restrictions since the ft level is not set by fs_core
for unamanged fts.
Fixes: 249ccc3c95 ("net/mlx5e: Add support for offloading traffic from uplink to uplink")
Signed-off-by: Ariel Levkovich <lariel@nvidia.com>
Aleksander Jan Bajkowski