The IO range size is set incorrectly for USB PHY0 deivice
it should be 24 instead of 32. Otherwise, It causes
USB PHY1 probing failure.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add Keystone IRQ controller IP node which allows ARM
CorePac core to receive signals from DSP cores.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The Keystone 2 has MDIO HW block which are compatible
to Davinci SoCs:
See "Gigabit Ethernet (GbE) Switch Subsystem"
See http://www.ti.com/lit/ug/sprugv9d/sprugv9d.pdf
Hence, add corresponding DT entry for Keystone 2.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This is a small follow-up to the larger ARM SoC updates merged
last week, almost entirely for the keystone platform.
The main change here is to use the new dma-ranges parsing code
that came in through Russell's ARM tree. This allows the keystone
platform to do cache-coherent DMA and to finally support all the
available physical memory when LPAE is enabled.
Aside from this, the keystone reset driver has been rewritten,
and there is a small bug fix to allow building the orion5x platform
again.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=AqkT
-----END PGP SIGNATURE-----
Merge tag 'soc2-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull part two of ARM SoC updates from Arnd Bergmann:
"This is a small follow-up to the larger ARM SoC updates merged last
week, almost entirely for the keystone platform.
The main change here is to use the new dma-ranges parsing code that
came in through Russell's ARM tree. This allows the keystone platform
to do cache-coherent DMA and to finally support all the available
physical memory when LPAE is enabled.
Aside from this, the keystone reset driver has been rewritten, and
there is a small bug fix to allow building the orion5x platform again"
* tag 'soc2-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: keystone: Drop use of meminfo since its not available anymore
ARM: orion5x: fix mvebu_mbus_dt_init call
ARM: configs: keystone: enable reset driver support
ARM: dts: keystone: update reset node to work with reset driver
ARM: keystone: remove redundant reset stuff
ARM: keystone: Update the dma offset for non-dt platform devices
ARM: keystone: Switch over to coherent memory address space
ARM: configs: keystone: add MTD_SPI_NOR (new dependency for M25P80)
ARM: configs: keystone: drop CONFIG_COMMON_CLK_DEBUG
The pll controller register set and device state control registers
include sets of registers with different purposes, so it's logically
to add syscon entry to be able to access them from appropriate places.
So added pll controller and device state control syscon entries.
The keystone driver requires the next additional properties:
"ti,syscon-pll" - phandle/offset pair. The phandle to syscon used to
access pll controller registers and the offset to use
reset control registers.
"ti,syscon-dev" - phandle/offset pair. The phandle to syscon used to
access device state control registers and the offset
in order to use mux block registers for all watchdogs.
"ti,wdt-list" - option to declare what watchdogs are used to reboot
the SoC, so set "0" WDT as default.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Keystone supports dma-coherent on USB master and also needs
dma-ranges to specify the hardware alias memory range in which DMA
can be operational.
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
The dma-ranges property has to be specified per bus and has format:
< DMA addr > - Base DMA address for Bus (Bus format 32-bits)
< CPU addr > - Corresponding base CPU address (CPU format 64-bits)
< DMA range size > - Size of supported DMA range
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
SPI nodes should always have #address-cells and #size-cells defined,
otherwise warnings will be produced in case of adding any child
nodes to the SPI bus in DT:
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc/spi@21000400/n25q128a11@0
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc/spi@21000400/n25q128a11@0
Hence, ensure that all SPIx nodes have #address-cells and #size-cells
properties defined.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
I2C devices are not the part of Keystone SoC and have to be
defined in board DTS files.
Hence, move i2c0 EEPROM device node from Keystone SoC to
k2hk, k2e, k2l EVM files as they all have similar EEPROM SoCs
installed.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
I2C nodes should always have #address-cells and #size-cells defined,
otherwise warnings will be produced in case of adding child
nodes to the I2C bus in DT:
Warning (avoid_default_addr_size): Relying on default #address-cells value for /soc/i2c@2530800/pca@20
Warning (avoid_default_addr_size): Relying on default #size-cells value for /soc/i2c@2530800/pca@20
Hence, ensure that all i2cX nodes have #address-cells and #size-cells
properties defined.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This is likely a copy-and-paste error from the
ARM GIC documentation, that has already been fixed.
address-cells should have been set to 0, as with the size
cells. As having those properties set to 0 is the
same thing as not specifying them, drop them completely.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Current keystone.dtsi includes SoC specific definitions for K2HK
SoCs. In order to support two addition keystone devices, k2 Edison
and K2 Lamarr and corresponding EVMs, This patch restructure the
dts files for the following:-
- All clock nodes that are only available in k2hk SoC are moved
from keystone-clocks.dtsi to a new k2hk-clocks.dtsi include file
- The CPU nodes are now part of the soc specific k2hk.dtsi.
- Change the compatibility string to ti,k2hk-evm and change
the model name accordingly
- Finally include k2hk-clocks.dtsi in k2hk.dtsi and that in
k2hk-evm.dts
Cc: Olof Johansson <olof@lixom.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch adds Keystone GPIO IP device definitions in DT which supports
up to 32 GPIO lines and each GPIO line can be configured as separate
interrupt source (so called "unbanked" IRQ).
For more information see:
http://www.ti.com/lit/ug/sprugv1/sprugv1.pdf
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add keystone timer entry to keystone device tree.
This 64-bit timer is used as backup clock event device.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Added device tree support for TI's Keystone USB driver and updated the
Documentation with device tree binding information.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Added device tree support for TI's Keystone USB PHY driver and updated the
Documentation with device tree binding information.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Update the Keystone gic device tree entry to add the maintenance
interrupt information.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Update the Keystone gic node to add the GICV and GIGH address space
needed by the KVM.
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
This patch adds K2 Kepler/Hawking evm (k2hk-evm) specific dts file.
To enable re-use of bindings across multiple evms of this family,
rename current keystone.dts to keystone.dtsi and include it in the
evm specific dts file.
K2 SoC has separate ref clock inputs for various clocks. So add
separate ref clock nodes for ARM, DDR3A, DDR3B and PA PLL input
clocks in k2hk-evm.dts. While at it, rename refclkmain to
refclksys based on device User Guide naming convention
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Grygorii Strashko