Uncorrected no action required (UCNA) - is a uncorrected recoverable
machine check error that is not signaled via a machine check exception
and, instead, is reported to system software as a corrected machine
check error. UCNA errors indicate that some data in the system is
corrupted, but the data has not been consumed and the processor state
is valid and you may continue execution on this processor. UCNA errors
require no action from system software to continue execution. Note that
UCNA errors are supported by the processor only when IA32_MCG_CAP[24]
(MCG_SER_P) is set.
-- Intel SDM Volume 3B
Deferred errors are errors that cannot be corrected by hardware, but
do not cause an immediate interruption in program flow, loss of data
integrity, or corruption of processor state. These errors indicate
that data has been corrupted but not consumed. Hardware writes information
to the status and address registers in the corresponding bank that
identifies the source of the error if deferred errors are enabled for
logging. Deferred errors are not reported via machine check exceptions;
they can be seen by polling the MCi_STATUS registers.
-- AMD64 APM Volume 2
Above two items, both UCNA and Deferred errors belong to detected
errors, but they can't be corrected by hardware, and this is very
similar to Software Recoverable Action Optional (SRAO) errors.
Therefore, we can take some actions that have been used for handling
SRAO errors to handle UCNA and Deferred errors.
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Chen Yucong <slaoub@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Until now, the mce_severity mechanism can only identify the severity
of UCNA error as MCE_KEEP_SEVERITY. Meanwhile, it is not able to filter
out DEFERRED error for AMD platform.
This patch extends the mce_severity mechanism for handling
UCNA/DEFERRED error. In order to do this, the patch introduces a new
severity level - MCE_UCNA/DEFERRED_SEVERITY.
In addition, mce_severity is specific to machine check exception,
and it will check MCIP/EIPV/RIPV bits. In order to use mce_severity
mechanism in non-exception context, the patch also introduces a new
argument (is_excp) for mce_severity. `is_excp' is used to explicitly
specify the calling context of mce_severity.
Reviewed-by: Aravind Gopalakrishnan <Aravind.Gopalakrishnan@amd.com>
Signed-off-by: Chen Yucong <slaoub@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There are some AMD CPU models which have thresholding banks but which
cannot generate a thresholding interrupt. This is denoted by the bit
MCi_MISC[IntP]. Make sure to check that bit before assigning the
thresholding interrupt handler.
Signed-off-by: Chen Yucong <slaoub@gmail.com>
[ Boris: save an indentation level and rewrite commit message. ]
Link: http://lkml.kernel.org/r/1412662128.28440.18.camel@debian
Signed-off-by: Borislav Petkov <bp@suse.de>
Aravind had the good question about why we're assigning a
software-defined bank when reporting error thresholding errors instead
of simply using the bank which reports the last error causing the
overflow.
Digging through git history, it pointed to
9526866439 ("[PATCH] x86_64: mce_amd support for family 0x10 processors")
which added that functionality. The problem with this, however, is that
tools don't know about software-defined banks and get puzzled. So drop
that K8_MCE_THRESHOLD_BASE and simply use the hw bank reporting the
thresholding interrupt.
Save us a couple of MSR reads while at it.
Reported-by: Aravind Gopalakrishnan <aravind.gopalakrishnan@amd.com>
Link: https://lkml.kernel.org/r/5435B206.60402@amd.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Assigning to mce_threshold_vector is loop-invariant code in
mce_amd_feature_init(). So do it only once, out of loop body.
Signed-off-by: Chen Yucong <slaoub@gmail.com>
Link: http://lkml.kernel.org/r/1412263212.8085.6.camel@debian
[ Boris: commit message corrections. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
mce_setup() does not gather the content of IA32_MCG_STATUS, so it
should be read explicitly. Moreover, we need to clear IA32_MCx_STATUS
to avoid that mce_log() logs the processed threshold event again
at next time.
But we do the logging ourselves and machine_check_poll() is completely
useless there. So kill it.
Signed-off-by: Chen Yucong <slaoub@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Avoid open coded calculations for bank MSRs by hiding the index
of higher bank MSRs in well-defined macros.
No semantic changes.
Signed-off-by: Chen Yucong <slaoub@gmail.com>
Link: http://lkml.kernel.org/r/1411438561-24319-1-git-send-email-slaoub@gmail.com
Signed-off-by: Borislav Petkov <bp@suse.de>
Pull percpu consistent-ops changes from Tejun Heo:
"Way back, before the current percpu allocator was implemented, static
and dynamic percpu memory areas were allocated and handled separately
and had their own accessors. The distinction has been gone for many
years now; however, the now duplicate two sets of accessors remained
with the pointer based ones - this_cpu_*() - evolving various other
operations over time. During the process, we also accumulated other
inconsistent operations.
This pull request contains Christoph's patches to clean up the
duplicate accessor situation. __get_cpu_var() uses are replaced with
with this_cpu_ptr() and __this_cpu_ptr() with raw_cpu_ptr().
Unfortunately, the former sometimes is tricky thanks to C being a bit
messy with the distinction between lvalues and pointers, which led to
a rather ugly solution for cpumask_var_t involving the introduction of
this_cpu_cpumask_var_ptr().
This converts most of the uses but not all. Christoph will follow up
with the remaining conversions in this merge window and hopefully
remove the obsolete accessors"
* 'for-3.18-consistent-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (38 commits)
irqchip: Properly fetch the per cpu offset
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t -fix
ia64: sn_nodepda cannot be assigned to after this_cpu conversion. Use __this_cpu_write.
percpu: Resolve ambiguities in __get_cpu_var/cpumask_var_t
Revert "powerpc: Replace __get_cpu_var uses"
percpu: Remove __this_cpu_ptr
clocksource: Replace __this_cpu_ptr with raw_cpu_ptr
sparc: Replace __get_cpu_var uses
avr32: Replace __get_cpu_var with __this_cpu_write
blackfin: Replace __get_cpu_var uses
tile: Use this_cpu_ptr() for hardware counters
tile: Replace __get_cpu_var uses
powerpc: Replace __get_cpu_var uses
alpha: Replace __get_cpu_var
ia64: Replace __get_cpu_var uses
s390: cio driver &__get_cpu_var replacements
s390: Replace __get_cpu_var uses
mips: Replace __get_cpu_var uses
MIPS: Replace __get_cpu_var uses in FPU emulator.
arm: Replace __this_cpu_ptr with raw_cpu_ptr
...
intel_init_thermal() is called from a) at the time of system initializing
and b) at the time of system resume to initialize thermal
monitoring.
In case when thermal monitoring is handled by SMI, we get to know it via
printk(). Currently it gives the message at both cases, but its okay if
we get it only once and no need to get the same message at every time
system resumes.
So, limit showing this message only at system boot time by avoid showing
at system resume and reduce abusing kernel log buffer.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1411068135.5121.10.camel@localhost.localdomain
Signed-off-by: Ingo Molnar <mingo@kernel.org>
__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x). This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.
Other use cases are for storing and retrieving data from the current
processors percpu area. __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.
__get_cpu_var() is defined as :
#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))
__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.
this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.
This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset. Thereby address calculations are avoided and less registers
are used when code is generated.
Transformations done to __get_cpu_var()
1. Determine the address of the percpu instance of the current processor.
DEFINE_PER_CPU(int, y);
int *x = &__get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(&y);
2. Same as #1 but this time an array structure is involved.
DEFINE_PER_CPU(int, y[20]);
int *x = __get_cpu_var(y);
Converts to
int *x = this_cpu_ptr(y);
3. Retrieve the content of the current processors instance of a per cpu
variable.
DEFINE_PER_CPU(int, y);
int x = __get_cpu_var(y)
Converts to
int x = __this_cpu_read(y);
4. Retrieve the content of a percpu struct
DEFINE_PER_CPU(struct mystruct, y);
struct mystruct x = __get_cpu_var(y);
Converts to
memcpy(&x, this_cpu_ptr(&y), sizeof(x));
5. Assignment to a per cpu variable
DEFINE_PER_CPU(int, y)
__get_cpu_var(y) = x;
Converts to
__this_cpu_write(y, x);
6. Increment/Decrement etc of a per cpu variable
DEFINE_PER_CPU(int, y);
__get_cpu_var(y)++
Converts to
__this_cpu_inc(y)
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86@kernel.org
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Commit ea431643d6 ("x86/mce: Fix CMCI preemption bugs") breaks RT by
the completely unrelated conversion of the cmci_discover_lock to a
regular (non raw) spinlock. This lock was annotated in commit
59d958d2c7 ("locking, x86: mce: Annotate cmci_discover_lock as raw")
with a proper explanation why.
The argument for converting the lock back to a regular spinlock was:
- it does percpu ops without disabling preemption. Preemption is not
disabled due to the mistaken use of a raw spinlock.
Which is complete nonsense. The raw_spinlock is disabling preemption in
the same way as a regular spinlock. In mainline spinlock maps to
raw_spinlock, in RT spinlock becomes a "sleeping" lock.
raw_spinlock has on RT exactly the same semantics as in mainline. And
because this lock is taken in non preemptible context it must be raw on
RT.
Undo the locking brainfart.
Reported-by: Clark Williams <williams@redhat.com>
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
BorisO reports that misc_register() fails often on xen. The current code
unregisters the CPU hotplug notifier in that case. If then a CPU is
offlined and onlined back again, we end up with a second timer running
on that CPU, leading to soft lockups and system hangs.
So let's leave the hotcpu notifier always registered - even if
mce_device_create failed for some cores and never unreg it so that we
can deal with the timer handling accordingly.
Reported-and-Tested-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: http://lkml.kernel.org/r/1403274493-1371-1-git-send-email-boris.ostrovsky@oracle.com
Signed-off-by: Borislav Petkov <bp@suse.de>
There is very little and maybe practically nothing we can do to recover
from a system where at least one core has reached a timeout during the
whole monarch cores gathering. So panic when that happens.
Link: http://lkml.kernel.org/r/20140523091041.GA21332@pd.tnic
Signed-off-by: Borislav Petkov <bp@suse.de>
As requested by Linus add explicit __visible to the asmlinkage users.
This marks all functions visible to assembler.
Tree sweep for arch/x86/*
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Link: http://lkml.kernel.org/r/1398984278-29319-3-git-send-email-andi@firstfloor.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The following commit:
27f6c573e0 ("x86, CMCI: Add proper detection of end of CMCI storms")
Added two preemption bugs:
- machine_check_poll() does a get_cpu_var() without a matching
put_cpu_var(), which causes preemption imbalance and crashes upon
bootup.
- it does percpu ops without disabling preemption. Preemption is not
disabled due to the mistaken use of a raw spinlock.
To fix these bugs fix the imbalance and change
cmci_discover_lock to a regular spinlock.
Reported-by: Owen Kibel <qmewlo@gmail.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Chen, Gong <gong.chen@linux.intel.com>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alexander Todorov <atodorov@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/n/tip-jtjptvgigpfkpvtQxpEk1at2@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
--
arch/x86/kernel/cpu/mcheck/mce.c | 4 +---
arch/x86/kernel/cpu/mcheck/mce_intel.c | 18 +++++++++---------
2 files changed, 10 insertions(+), 12 deletions(-)
Pull x86 fixes from Peter Anvin:
"This is a collection of minor fixes for x86, plus the IRET information
leak fix (forbid the use of 16-bit segments in 64-bit mode)"
NOTE! We may have to relax the "forbid the use of 16-bit segments in
64-bit mode" part, since there may be people who still run and depend on
16-bit Windows binaries under Wine.
But I'm taking this in the current unconditional form for now to see who
(if anybody) screams bloody murder. Maybe nobody cares. And maybe
we'll have to update it with some kind of runtime enablement (like our
vm.mmap_min_addr tunable that people who run dosemu/qemu/wine already
need to tweak).
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64, modify_ldt: Ban 16-bit segments on 64-bit kernels
efi: Pass correct file handle to efi_file_{read,close}
x86/efi: Correct EFI boot stub use of code32_start
x86/efi: Fix boot failure with EFI stub
x86/platform/hyperv: Handle VMBUS driver being a module
x86/apic: Reinstate error IRQ Pentium erratum 3AP workaround
x86, CMCI: Add proper detection of end of CMCI storms
When CMCI storm persists for a long time(at least beyond predefined
threshold. It's 30 seconds for now), we can watch CMCI storm is
detected immediately after it subsides.
...
Dec 10 22:04:29 kernel: CMCI storm detected: switching to poll mode
Dec 10 22:04:59 kernel: CMCI storm subsided: switching to interrupt mode
Dec 10 22:04:59 kernel: CMCI storm detected: switching to poll mode
Dec 10 22:05:29 kernel: CMCI storm subsided: switching to interrupt mode
...
The problem is that our logic that determines that the storm has
ended is incorrect. We announce the end, re-enable interrupts and
realize that the storm is still going on, so we switch back to
polling mode. Rinse, repeat.
When a storm happens we disable signaling of errors via CMCI and begin
polling machine check banks instead. If we find any logged errors,
then we need to set a per-cpu flag so that our per-cpu tests that
check whether the storm is ongoing will see that errors are still
being logged independently of whether mce_notify_irq() says that the
error has been fully processed.
cmci_clear() is not the right tool to disable a bank. It disables the
interrupt for the bank as desired, but it also clears the bit for
this bank in "mce_banks_owned" so we will skip the bank when polling
(so we fail to see that the storm continues because we stop looking).
New cmci_storm_disable_banks() just disables the interrupt while
allowing polling to continue.
Reported-by: William Dauchy <wdauchy@gmail.com>
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
After fixing the CPU hotplug callback registration code, the callbacks
invoked for each online CPU, during the initialization phase in
thermal_throttle_init_device(), can no longer race with the actual CPU
hotplug notifier callbacks (in thermal_throttle_cpu_callback). Hence the
therm_cpu_lock is unnecessary now. Remove it.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Instead, the correct and race-free way of performing the callback
registration is:
cpu_notifier_register_begin();
for_each_online_cpu(cpu)
init_cpu(cpu);
/* Note the use of the double underscored version of the API */
__register_cpu_notifier(&foobar_cpu_notifier);
cpu_notifier_register_done();
Fix the thermal throttle code in x86 by using this latter form of callback
registration.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Subsystems that want to register CPU hotplug callbacks, as well as perform
initialization for the CPUs that are already online, often do it as shown
below:
get_online_cpus();
for_each_online_cpu(cpu)
init_cpu(cpu);
register_cpu_notifier(&foobar_cpu_notifier);
put_online_cpus();
This is wrong, since it is prone to ABBA deadlocks involving the
cpu_add_remove_lock and the cpu_hotplug.lock (when running concurrently
with CPU hotplug operations).
Instead, the correct and race-free way of performing the callback
registration is:
cpu_notifier_register_begin();
for_each_online_cpu(cpu)
init_cpu(cpu);
/* Note the use of the double underscored version of the API */
__register_cpu_notifier(&foobar_cpu_notifier);
cpu_notifier_register_done();
Fix the mce code in x86 by using this latter form of callback registration.
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull x86 RAS changes from Ingo Molnar:
- SCI reporting for other error types not only correctable ones
- GHES cleanups
- Add the functionality to override error reporting agents as some
machines are sporting a new extended error logging capability which,
if done properly in the BIOS, makes a corresponding EDAC module
redundant
- PCIe AER tracepoint severity levels fix
- Error path correction for the mce device init
- MCE timer fix
- Add more flexibility to the error injection (EINJ) debugfs interface
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, mce: Fix mce_start_timer semantics
ACPI, APEI, GHES: Cleanup ghes memory error handling
ACPI, APEI: Cleanup alignment-aware accesses
ACPI, APEI, GHES: Do not report only correctable errors with SCI
ACPI, APEI, EINJ: Changes to the ACPI/APEI/EINJ debugfs interface
ACPI, eMCA: Combine eMCA/EDAC event reporting priority
EDAC, sb_edac: Modify H/W event reporting policy
EDAC: Add an edac_report parameter to EDAC
PCI, AER: Fix severity usage in aer trace event
x86, mce: Call put_device on device_register failure
So mce_start_timer() has a 'cpu' argument which is supposed to mean to
start a timer on that cpu. However, the code currently starts a timer on
the *current* cpu the function runs on and causes the sanity-check in
mce_timer_fn to fire:
WARNING: CPU: 0 PID: 0 at arch/x86/kernel/cpu/mcheck/mce.c:1286 mce_timer_fn
because it is running on the wrong cpu.
This was triggered by Prarit Bhargava <prarit@redhat.com> by offlining
all the cpus in succession.
Then, we were fiddling with the CMCI storm settings when starting the
timer whereas there's no need for that - if there's storm happening
on this newly restarted cpu, we're going to be in normal CMCI mode
initially and then when the CMCI interrupt starts firing, we're going to
go to the polling mode with the timer real soon.
Signed-off-by: Borislav Petkov <bp@suse.de>
Tested-by: Prarit Bhargava <prarit@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Reviewed-by: Chen, Gong <gong.chen@linux.intel.com>
Link: http://lkml.kernel.org/r/1387722156-5511-1-git-send-email-prarit@redhat.com
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
[ hpa: undid incorrect removal from arch/x86/kernel/head_32.S ]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Link: http://lkml.kernel.org/r/1389054026-12947-1-git-send-email-paul.gortmaker@windriver.com
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Currently SCI is employed to handle corrected errors - memory corrected
errors, more specifically but in fact SCI still can be used to handle
any errors, e.g. uncorrected or even fatal ones if enabled by the BIOS.
Enable logging for those kinds of errors too.
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Cc: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/1385363701-12387-1-git-send-email-gong.chen@linux.intel.com
[ Boris: massage commit message, rename function arg. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
This patch adds a call to put_device() when the device_register() call
has failed. This is required so that the last reference to the device is
given up.
Signed-off-by: Levente Kurusa <levex@linux.com>
Link: http://lkml.kernel.org/r/5298F900.9000208@linux.com
Signed-off-by: Borislav Petkov <bp@suse.de>
In latest UEFI spec(by now it is 2.4) memory error definition
for CPER (UEFI 2.4 Appendix N Common Platform Error Record)
adds some new fields. These fields help people to locate
memory error to an actual DIMM location.
Original-author: Tony Luck <tony.luck@intel.com>
Signed-off-by: Chen, Gong <gong.chen@linux.intel.com>
Reviewed-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
an uncorrected error is reported. Ignore it when checking
error signatures.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=LbVP
-----END PGP SIGNATURE-----
Merge tag 'please-pull-mce-f-bit' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/ras
Pull MCE-uncorrected-error fix from Tony Luck:
"Bit 12 may or may not be set in MCi_STATUS.MCACOD when
an uncorrected error is reported. Ignore it when checking
error signatures."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In commit 33d7885b59
x86/mce: Update MCE severity condition check
We simplified the rules to recognise each classification of recoverable
machine check combining the instruction and data fetch rules into a
single entry based on clarifications in the June 2013 SDM that all
recoverable events would be reported on the unaffected processor with
MCG_STATUS.EIPV=0 and MCG_STATUS.RIPV=1. Unfortunately the simplified
rule has a couple of bugs. Fix them here.
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/x86 uses of the __cpuinit macros from
all C files. x86 only had the one __CPUINIT used in assembly files,
and it wasn't paired off with a .previous or a __FINIT, so we can
delete it directly w/o any corresponding additional change there.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Pull thermal management updates from Zhang Rui:
"There are not too many changes this time, except two new platform
thermal drivers, ti-soc-thermal driver and x86_pkg_temp_thermal
driver, and a couple of small fixes.
Highlights:
- move the ti-soc-thermal driver out of the staging tree to the
thermal tree.
- introduce the x86_pkg_temp_thermal driver. This driver registers
CPU digital temperature package level sensor as a thermal zone.
- small fixes/cleanups including removing redundant use of
platform_set_drvdata() and of_match_ptr for all platform thermal
drivers"
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux: (34 commits)
thermal: cpu_cooling: fix stub function
thermal: ti-soc-thermal: use standard GPIO DT bindings
thermal: MAINTAINERS: Add git tree path for SoC specific updates
thermal: fix x86_pkg_temp_thermal.c build and Kconfig
Thermal: Documentation for x86 package temperature thermal driver
Thermal: CPU Package temperature thermal
thermal: consider emul_temperature while computing trend
thermal: ti-soc-thermal: add DT example for DRA752 chip
thermal: ti-soc-thermal: add dra752 chip to device table
thermal: ti-soc-thermal: add thermal data for DRA752 chips
thermal: ti-soc-thermal: remove usage of IS_ERR_OR_NULL
thermal: ti-soc-thermal: freeze FSM while computing trend
thermal: ti-soc-thermal: remove external heat while extrapolating hotspot
thermal: ti-soc-thermal: update DT reference for OMAP5430
x86, mcheck, therm_throt: Process package thresholds
thermal: cpu_cooling: fix 'descend' check in get_property()
Thermal: spear: Remove redundant use of of_match_ptr
Thermal: kirkwood: Remove redundant use of of_match_ptr
Thermal: dove: Remove redundant use of of_match_ptr
Thermal: armada: Remove redundant use of of_match_ptr
...
The Corrected Machine Check structure (CMC) in HEST has a flag which can be
set by the firmware to indicate to the OS that it prefers to process the
corrected error events first. In this scenario, the OS is expected to not
monitor for corrected errors (through CMCI/polling). Instead, the firmware
notifies the OS on corrected error events through GHES.
Linux already has support for GHES. This patch adds support for parsing CMC
structure and to disable CMCI/polling if the firmware first flag is set.
Further, the list of machine check bank structures at the end of CMC is used
to determine which MCA banks function in FF mode, so that we continue to
monitor error events on the other banks.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=Dm06
-----END PGP SIGNATURE-----
Merge tag 'please-pull-mce-therm' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux
Pull thermal power-limit update from Tony Luck:
"Thermal limit warnings are too scary and cause unnecessary concern"
* tag 'please-pull-mce-therm' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux:
x86 thermal: Disable power limit notification interrupt by default
x86 thermal: Delete power-limit-notification console messages
Pull x86 tracing updates from Ingo Molnar:
"This tree adds IRQ vector tracepoints that are named after the handler
and which output the vector #, based on a zero-overhead approach that
relies on changing the IDT entries, by Seiji Aguchi.
The new tracepoints look like this:
# perf list | grep -i irq_vector
irq_vectors:local_timer_entry [Tracepoint event]
irq_vectors:local_timer_exit [Tracepoint event]
irq_vectors:reschedule_entry [Tracepoint event]
irq_vectors:reschedule_exit [Tracepoint event]
irq_vectors:spurious_apic_entry [Tracepoint event]
irq_vectors:spurious_apic_exit [Tracepoint event]
irq_vectors:error_apic_entry [Tracepoint event]
irq_vectors:error_apic_exit [Tracepoint event]
[...]"
* 'x86-tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/tracing: Add config option checking to the definitions of mce handlers
trace,x86: Do not call local_irq_save() in load_current_idt()
trace,x86: Move creation of irq tracepoints from apic.c to irq.c
x86, trace: Add irq vector tracepoints
x86: Rename variables for debugging
x86, trace: Introduce entering/exiting_irq()
tracing: Add DEFINE_EVENT_FN() macro
the code for SRAR (software recoverable action required) errors.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=PJXS
-----END PGP SIGNATURE-----
Merge tag 'please-pull-mce' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/ras
Pull MCE cleanup from Tony Luck:
"Changes to simplify the SDM means that we can also simplify
the code for SRAR (software recoverable action required) errors."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Update some SRAR severity conditions check to make it clearer,
according to latest Intel SDM Vol 3(June 2013), table 15-20.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Acked-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There is some confusion about the 'mce_poll_banks' and 'mce_banks_owned'
per-cpu bitmaps. Provide comments so that we all know exactly what these
are used for, and why.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
[Purpose of this patch]
As Vaibhav explained in the thread below, tracepoints for irq vectors
are useful.
http://www.spinics.net/lists/mm-commits/msg85707.html
<snip>
The current interrupt traces from irq_handler_entry and irq_handler_exit
provide when an interrupt is handled. They provide good data about when
the system has switched to kernel space and how it affects the currently
running processes.
There are some IRQ vectors which trigger the system into kernel space,
which are not handled in generic IRQ handlers. Tracing such events gives
us the information about IRQ interaction with other system events.
The trace also tells where the system is spending its time. We want to
know which cores are handling interrupts and how they are affecting other
processes in the system. Also, the trace provides information about when
the cores are idle and which interrupts are changing that state.
<snip>
On the other hand, my usecase is tracing just local timer event and
getting a value of instruction pointer.
I suggested to add an argument local timer event to get instruction pointer before.
But there is another way to get it with external module like systemtap.
So, I don't need to add any argument to irq vector tracepoints now.
[Patch Description]
Vaibhav's patch shared a trace point ,irq_vector_entry/irq_vector_exit, in all events.
But there is an above use case to trace specific irq_vector rather than tracing all events.
In this case, we are concerned about overhead due to unwanted events.
So, add following tracepoints instead of introducing irq_vector_entry/exit.
so that we can enable them independently.
- local_timer_vector
- reschedule_vector
- call_function_vector
- call_function_single_vector
- irq_work_entry_vector
- error_apic_vector
- thermal_apic_vector
- threshold_apic_vector
- spurious_apic_vector
- x86_platform_ipi_vector
Also, introduce a logic switching IDT at enabling/disabling time so that a time penalty
makes a zero when tracepoints are disabled. Detailed explanations are as follows.
- Create trace irq handlers with entering_irq()/exiting_irq().
- Create a new IDT, trace_idt_table, at boot time by adding a logic to
_set_gate(). It is just a copy of original idt table.
- Register the new handlers for tracpoints to the new IDT by introducing
macros to alloc_intr_gate() called at registering time of irq_vector handlers.
- Add checking, whether irq vector tracing is on/off, into load_current_idt().
This has to be done below debug checking for these reasons.
- Switching to debug IDT may be kicked while tracing is enabled.
- On the other hands, switching to trace IDT is kicked only when debugging
is disabled.
In addition, the new IDT is created only when CONFIG_TRACING is enabled to avoid being
used for other purposes.
Signed-off-by: Seiji Aguchi <seiji.aguchi@hds.com>
Link: http://lkml.kernel.org/r/51C323ED.5050708@hds.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
When implementing tracepoints in interrupt handers, if the tracepoints are
simply added in the performance sensitive path of interrupt handers,
it may cause potential performance problem due to the time penalty.
To solve the problem, an idea is to prepare non-trace/trace irq handers and
switch their IDTs at the enabling/disabling time.
So, let's introduce entering_irq()/exiting_irq() for pre/post-
processing of each irq handler.
A way to use them is as follows.
Non-trace irq handler:
smp_irq_handler()
{
entering_irq(); /* pre-processing of this handler */
__smp_irq_handler(); /*
* common logic between non-trace and trace handlers
* in a vector.
*/
exiting_irq(); /* post-processing of this handler */
}
Trace irq_handler:
smp_trace_irq_handler()
{
entering_irq(); /* pre-processing of this handler */
trace_irq_entry(); /* tracepoint for irq entry */
__smp_irq_handler(); /*
* common logic between non-trace and trace handlers
* in a vector.
*/
trace_irq_exit(); /* tracepoint for irq exit */
exiting_irq(); /* post-processing of this handler */
}
If tracepoints can place outside entering_irq()/exiting_irq() as follows,
it looks cleaner.
smp_trace_irq_handler()
{
trace_irq_entry();
smp_irq_handler();
trace_irq_exit();
}
But it doesn't work.
The problem is with irq_enter/exit() being called. They must be called before
trace_irq_enter/exit(), because of the rcu_irq_enter() must be called before
any tracepoints are used, as tracepoints use rcu to synchronize.
As a possible alternative, we may be able to call irq_enter() first as follows
if irq_enter() can nest.
smp_trace_irq_hander()
{
irq_entry();
trace_irq_entry();
smp_irq_handler();
trace_irq_exit();
irq_exit();
}
But it doesn't work, either.
If irq_enter() is nested, it may have a time penalty because it has to check if it
was already called or not. The time penalty is not desired in performance sensitive
paths even if it is tiny.
Signed-off-by: Seiji Aguchi <seiji.aguchi@hds.com>
Link: http://lkml.kernel.org/r/51C3238D.9040706@hds.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
The package power limit notification interrupt is primarily for
system diagnosis, and should not be blindly enabled on every
system by default -- particuarly since Linux does nothing in the
handler except count how many times it has been called...
Add a new kernel cmdline parameter "int_pln_enable" for situations where
users want to oberve these events via existing system counters:
$ grep TRM /proc/interrupts
$ grep . /sys/devices/system/cpu/cpu*/thermal_throttle/*
https://bugzilla.kernel.org/show_bug.cgi?id=36182
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Package power limits are common on some systems under some conditions --
so printing console messages when limits are reached
causes unnecessary customer concern and support calls.
Note that even with these console messages gone,
the events can still be observed via system counters:
$ grep TRM /proc/interrupts
Shows total thermal interrupts, which includes both power
limit notifications and thermal throttling interrupts.
$ grep . /sys/devices/system/cpu/cpu*/thermal_throttle/*
Will show what caused those interrupts, core and package
throttling and power limit notifications.
https://bugzilla.kernel.org/show_bug.cgi?id=36182
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Added callback registration for package threshold reports. Also added
a callback to check the rate control implemented in callback or not.
If there is no rate control implemented, then there is a default rate
control similar to core threshold notification by delaying for
CHECK_INTERVAL (5 minutes) between reports.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wipk
-----END PGP SIGNATURE-----
Merge tag 'please-pull-cmci_rediscover' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/ras
Pull clean up of the cmci_rediscover code to fix problems found by Dave Jones,
from Tony Luck.
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Dave Jones reports that offlining a CPU leads to this trace:
numa_remove_cpu cpu 1 node 0: mask now 0,2-3
smpboot: CPU 1 is now offline
BUG: using smp_processor_id() in preemptible [00000000] code:
cpu-offline.sh/10591
caller is cmci_rediscover+0x6a/0xe0
Pid: 10591, comm: cpu-offline.sh Not tainted 3.9.0-rc3+ #2
Call Trace:
[<ffffffff81333bbd>] debug_smp_processor_id+0xdd/0x100
[<ffffffff8101edba>] cmci_rediscover+0x6a/0xe0
[<ffffffff815f5b9f>] mce_cpu_callback+0x19d/0x1ae
[<ffffffff8160ea66>] notifier_call_chain+0x66/0x150
[<ffffffff8107ad7e>] __raw_notifier_call_chain+0xe/0x10
[<ffffffff8104c2e3>] cpu_notify+0x23/0x50
[<ffffffff8104c31e>] cpu_notify_nofail+0xe/0x20
[<ffffffff815ef082>] _cpu_down+0x302/0x350
[<ffffffff815ef106>] cpu_down+0x36/0x50
[<ffffffff815f1c9d>] store_online+0x8d/0xd0
[<ffffffff813edc48>] dev_attr_store+0x18/0x30
[<ffffffff81226eeb>] sysfs_write_file+0xdb/0x150
[<ffffffff811adfb2>] vfs_write+0xa2/0x170
[<ffffffff811ae16c>] sys_write+0x4c/0xa0
[<ffffffff81613019>] system_call_fastpath+0x16/0x1b
However, a look at cmci_rediscover shows that it can be simplified quite
a bit, apart from solving the above issue. It invokes functions that
take spin locks with interrupts disabled, and hence it can run in atomic
context. Also, it is run in the CPU_POST_DEAD phase, so the dying CPU
is already dead and out of the cpu_online_mask. So take these points into
account and simplify the code, and thereby also fix the above issue.
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Currently number of error reporting register banks is hardcoded to
6 on AMD processors. This may break in virtualized scenarios when
a hypervisor prefers to report fewer banks than what the physical
HW provides.
Since number of supported banks is reported in MSR_IA32_MCG_CAP[7:0]
that's what we should use.
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: http://lkml.kernel.org/r/1363295441-1859-3-git-send-email-boris.ostrovsky@oracle.com
[ reverse NULL ptr test logic ]
Signed-off-by: Borislav Petkov <bp@suse.de>
lockdep, but it's a mechanical change.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tiSY
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module update from Rusty Russell:
"The sweeping change is to make add_taint() explicitly indicate whether
to disable lockdep, but it's a mechanical change."
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
MODSIGN: Add option to not sign modules during modules_install
MODSIGN: Add -s <signature> option to sign-file
MODSIGN: Specify the hash algorithm on sign-file command line
MODSIGN: Simplify Makefile with a Kconfig helper
module: clean up load_module a little more.
modpost: Ignore ARC specific non-alloc sections
module: constify within_module_*
taint: add explicit flag to show whether lock dep is still OK.
module: printk message when module signature fail taints kernel.
Fix up all callers as they were before, with make one change: an
unsigned module taints the kernel, but doesn't turn off lockdep.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
There's no need to test whether a (delayed) work item in pending
before queueing, flushing or cancelling it. Most uses are unnecessary
and quite a few of them are buggy.
Remove unnecessary pending tests from x86/mce. Only compile tested.
v2: Local var work removed from mce_schedule_work() as suggested by
Borislav.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Borislav Petkov <bp@alien8.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac@vger.kernel.org
Pull x86 RAS update from Ingo Molnar:
"Rework all config variables used throughout the MCA code and collect
them together into a mca_config struct. This keeps them tightly and
neatly packed together instead of spilled all over the place.
Then, convert those which are used as booleans into real booleans and
save some space. These bits are exposed via
/sys/devices/system/machinecheck/machinecheck*/"
* 'x86-ras-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, MCA: Finish mca_config conversion
x86, MCA: Convert the next three variables batch
x86, MCA: Convert rip_msr, mce_bootlog, monarch_timeout
x86, MCA: Convert dont_log_ce, banks and tolerant
drivers/base: Add a DEVICE_BOOL_ATTR macro
migrating worker threads to other cpus.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=tv13
-----END PGP SIGNATURE-----
Merge tag 'please-pull-tangchen' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras into x86/urgent
Pull MCE fix from Tony Luck:
"Fix problem in CMCI rediscovery code that was illegally
migrating worker threads to other cpus."
Signed-off-by: Ingo Molnar <mingo@kernel.org>
mce_ser, mce_bios_cmci_threshold and mce_disabled are the last three
bools which need conversion. Move them to the mca_config struct and
adjust usage sites accordingly.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Move them into the mca_config struct and adjust code touching them
accordingly.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Acked-by: Tony Luck <tony.luck@intel.com>
Move those MCA configuration variables into struct mca_config and adjust
the places they're used accordingly.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Acked-by: Tony Luck <tony.luck@intel.com>
From Borislav Petkov <bp@amd64.org>:
Below is a RAS fix which reverts the addition of a sysfs attribute
which we agreed is not needed, post-factum. And this should go in now
because that sysfs attribute is going to end up in 3.7 otherwise and
thus exposed to userspace; removing it then would be a lot harder.
This is done as a merge rather than a simple patch/cherry-pick since
the baseline for this patch was not in the previous x86/urgent.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
450cc20103 ("x86/mce: Provide boot argument to honour bios-set CMCI
threshold") added the bios_cmci_threshold sysfs attribute which was
supposed to communicate to userspace tools that BIOS CMCI threshold has
been honoured.
However, this info is not of any importance to userspace - it should
rather get the actual error count it has been thresholded already from
MCi_STATUS[38:52].
So drop this before it becomes a used interface (good thing we caught
this early in 3.7-rc1, right after the merge window closed).
Cc: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20121017105940.GA14590@x1.osrc.amd.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
When booting on a federated multi-server system (NumaScale), the
processor Northbridge lookup returns NULL; add guards to prevent this
causing an oops.
On those systems, the northbridge is accessed through MMIO and the
"normal" northbridge enumeration in amd_nb.c doesn't work since we're
generating the northbridge ID from the initial APIC ID and the last
is not unique on those systems. Long story short, we end up without
northbridge descriptors.
Signed-off-by: Daniel J Blueman <daniel@numascale-asia.com>
Cc: stable@vger.kernel.org # 3.6
Link: http://lkml.kernel.org/r/1349073725-14093-1-git-send-email-daniel@numascale-asia.com
[ Boris: beef up commit message ]
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The ACPI spec doesn't provide for a way for the bios to pass down
recommended thresholds to the OS on a _per-bank_ basis. This patch adds
a new boot option, which if passed, tells Linux to use CMCI thresholds
set by the bios.
As fail-safe, we initialize threshold to 1 if some banks have not been
initialized by the bios and warn the user.
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
On Intel systems corrected machine check interrupts (CMCI) may be sent to
multiple logical processors; possibly to all processors on the affected
socket (SDM Volume 3B "15.5.1 CMCI Local APIC Interface"). This means
that a persistent error (such as a stuck bit in ECC memory) may cause
a storm of interrupts that greatly hinders or prevents forward progress
(probably on many processors).
To solve this we keep track of the rate at which each processor sees
CMCI. If we exceed a threshold, we disable CMCI delivery and switch to
polling the machine check banks. If the storm subsides (none of the
affected processors see any more errors for a complete poll interval) we
re-enable CMCI.
[Tony: Added console messages when storm begins/ends and increased storm
threshold from 5 to 15 so we have a few more logged entries before we
disable interrupts and start dropping reports]
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
cmci_discover() works out which machine check banks support CMCI, and
which of those are shared by multiple logical processors. It uses this
information to ensure that exactly one cpu is designated the owner of
each bank so that when interrupts are broadcast to multiple cpus, only one
of them will look in a shared bank to log the error and clear the bank.
At boot time cmci_discover() performs this task silently. But during
certain cpu hotplug operations it prints out a set of summary lines
like this:
CPU 35 MCA banks CMCI:0 CMCI:1 CMCI:3 CMCI:5 CMCI:6 CMCI:7 CMCI:8 CMCI:9 CMCI:10 CMCI:11
CPU 1 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 39 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 38 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 32 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 37 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 36 MCA banks CMCI:0 CMCI:1 CMCI:3
CPU 34 MCA banks CMCI:0 CMCI:1 CMCI:3
The value of these messages seems very low. A user might painstakingly
cross-check against the data sheet for a processor to ensure that all
CMCI supported banks are correctly reported, but this seems improbable.
If users really wanted to do this, we should print the information at
boot time too.
Remove the messages.
Signed-off-by: Tony Luck <tony.luck@intel.com>
No point in having double cases if we can simply mask the FROZEN bit
out.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Split timer init function into the init and the start part, so the
start part can replace the open coded version in CPU_DOWN_FAILED.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
raise_mce() fiddles with global state, but lacks any kind of
serialization.
Add a mutex around the raise_mce() call, so concurrent writers do not
stomp on each other toes.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
raise_mce() has a code path which does not disable preemption when the
raise_local() is called. The per cpu variable access in raise_local()
depends on preemption being disabled to be functional. So that code
path was either never tested or never tested with CONFIG_DEBUG_PREEMPT
enabled.
Add the missing preempt_disable/enable() pair around the call.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pull x86 fixes from Ingo Molnar:
"Various fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64, kcmp: The kcmp system call can be common
arch/x86/kernel/kdebugfs.c: Ensure a consistent return value in error case
x86/mce: Add quirk for instruction recovery on Sandy Bridge processors
x86/mce: Move MCACOD defines from mce-severity.c to <asm/mce.h>
x86/ioapic: Fix NULL pointer dereference on CPU hotplug after disabling irqs
x86, nops: Missing break resulting in incorrect selection on Intel
x86: CONFIG_CC_STACKPROTECTOR=y is no longer experimental
Sandy Bridge processors follow the SDM (Vol 3B, Table 15-20) and
set both the RIPV and EIPV bits in the MCG_STATUS register to
zero for machine checks during instruction fetch. This is more
than a little counter-intuitive and means that Linux cannot
recover from these errors. Rather than insert special case code
at several places in mce.c and mce-severity.c, we pretend the
EIPV bit was set for just this case early in processing the
machine check.
Acked-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Link: http://lkml.kernel.org/r/180a06f3f357cf9f78259ae443a082b14a29535b.1343078495.git.tony.luck@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We will need some of these values in mce.c. Move them to the
appropriate header file so they are available.
Acked-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Link: http://lkml.kernel.org/r/0ccfb1af5fe35e537b7cd8e4d448bf7d851dbfb9.1343078495.git.tony.luck@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
* Performance improvement to lower the amount of traps the hypervisor
has to do 32-bit guests. Mainly for setting PTE entries and updating
TLS descriptors.
* MCE polling driver to collect hypervisor MCE buffer and present them to
/dev/mcelog.
* Physical CPU online/offline support. When an privileged guest is booted
it is present with virtual CPUs, which might have an 1:1 to physical
CPUs but usually don't. This provides mechanism to offline/online physical
CPUs.
Bug-fixes for:
* Coverity found fixes in the console and ACPI processor driver.
* PVonHVM kexec fixes along with some cleanups.
* Pages that fall within E820 gaps and non-RAM regions (and had been
released to hypervisor) would be populated back, but potentially in
non-RAM regions.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQDWcvAAoJEFjIrFwIi8fJ6GAH/iFIkOC5wseD8qZ9nV4VI46t
0GYvBFC4F91NvC7CNfoAySr84v+ZORIZzMcdyDF8H/tLO9MaOY/Mwn0S5ZSqmYMi
rhskvK3InBaVkYtceOHugNGM7mB0c3STIm7OsjW6gbVzohmTN25rbQR+X5iWAtVA
cTUtDyH3AU15mwuVT3U+VC4IulHpnNJz4pHoq3Sn61/UK1LYmhLXYd5fveA0D0B8
lRZTAvNMsYDJDDmkWNrs8RczKkQ86DTSjfGawm0YG+Gf94GgD5yMHWbiHh2Gy93e
u7sHK0RrKbP5BY/MV6vVJxkoV5NoWgCc0tcjBcYwdyvwzxDS75UhV6uoVHC3Ao8=
=drt2
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen
Pull Xen update from Konrad Rzeszutek Wilk:
"Features:
* Performance improvement to lower the amount of traps the hypervisor
has to do 32-bit guests. Mainly for setting PTE entries and
updating TLS descriptors.
* MCE polling driver to collect hypervisor MCE buffer and present
them to /dev/mcelog.
* Physical CPU online/offline support. When an privileged guest is
booted it is present with virtual CPUs, which might have an 1:1 to
physical CPUs but usually don't. This provides mechanism to
offline/online physical CPUs.
Bug-fixes for:
* Coverity found fixes in the console and ACPI processor driver.
* PVonHVM kexec fixes along with some cleanups.
* Pages that fall within E820 gaps and non-RAM regions (and had been
released to hypervisor) would be populated back, but potentially in
non-RAM regions."
* tag 'stable/for-linus-3.6-rc0-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen: populate correct number of pages when across mem boundary (v2)
xen PVonHVM: move shared_info to MMIO before kexec
xen: simplify init_hvm_pv_info
xen: remove cast from HYPERVISOR_shared_info assignment
xen: enable platform-pci only in a Xen guest
xen/pv-on-hvm kexec: shutdown watches from old kernel
xen/x86: avoid updating TLS descriptors if they haven't changed
xen/x86: add desc_equal() to compare GDT descriptors
xen/mm: zero PTEs for non-present MFNs in the initial page table
xen/mm: do direct hypercall in xen_set_pte() if batching is unavailable
xen/hvc: Fix up checks when the info is allocated.
xen/acpi: Fix potential memory leak.
xen/mce: add .poll method for mcelog device driver
xen/mce: schedule a workqueue to avoid sleep in atomic context
xen/pcpu: Xen physical cpus online/offline sys interface
xen/mce: Register native mce handler as vMCE bounce back point
x86, MCE, AMD: Adjust initcall sequence for xen
xen/mce: Add mcelog support for Xen platform
Pull x86/mce changes from Ingo Molnar:
"This tree improves the AMD thresholding bank code and includes a
memory fault signal handling fixlet."
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mce: Fix siginfo_t->si_addr value for non-recoverable memory faults
x86, MCE, AMD: Update copyrights and boilerplate
x86, MCE, AMD: Give proper names to the thresholding banks
x86, MCE, AMD: Make error_count read only
x86, MCE, AMD: Cleanup reading of error_count
x86, MCE, AMD: Print decimal thresholding values
x86, MCE, AMD: Move shared bank to node descriptor
x86, MCE, AMD: Remove local_allocate_... wrapper
x86, MCE, AMD: Remove shared banks sysfs linking
x86, amd_nb: Export model 0x10 and later PCI id
there are 3 funcs which need to be _initcalled in a logic sequence:
1. xen_late_init_mcelog
2. mcheck_init_device
3. threshold_init_device
xen_late_init_mcelog must register xen_mce_chrdev_device before
native mce_chrdev_device registration if running under xen platform;
mcheck_init_device should be inited before threshold_init_device to
initialize mce_device, otherwise a a NULL ptr dereference will cause panic.
so we use following _initcalls
1. device_initcall(xen_late_init_mcelog);
2. device_initcall_sync(mcheck_init_device);
3. late_initcall(threshold_init_device);
when running under xen, the initcall order is 1,2,3;
on baremetal, we skip 1 and we do only 2 and 3.
Acked-and-tested-by: Borislav Petkov <bp@amd64.org>
Suggested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Liu, Jinsong <jinsong.liu@intel.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
When MCA error occurs, it would be handled by Xen hypervisor first,
and then the error information would be sent to initial domain for logging.
This patch gets error information from Xen hypervisor and convert
Xen format error into Linux format mcelog. This logic is basically
self-contained, not touching other kernel components.
By using tools like mcelog tool users could read specific error information,
like what they did under native Linux.
To test follow directions outlined in Documentation/acpi/apei/einj.txt
Acked-and-tested-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Ke, Liping <liping.ke@intel.com>
Signed-off-by: Jiang, Yunhong <yunhong.jiang@intel.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Liu, Jinsong <jinsong.liu@intel.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
In commit dad1743e59 ("x86/mce: Only restart instruction after machine
check recovery if it is safe") we fixed mce_notify_process() to force a
signal to the current process if it was not restartable (RIPV bit not
set in MCG_STATUS). But doing it here means that the process doesn't
get told the virtual address of the fault via siginfo_t->si_addr. This
would prevent application level recovery from the fault.
Make a new MF_MUST_KILL flag bit for memory_failure() et al. to use so
that we will provide the right information with the signal.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: stable@kernel.org # 3.4+
Until now, writing to error count caused the code to reset the
thresholding bank to the current thresholding limit and start counting
errors from the beginning.
This is misleading and unclear, and can be accomplished by writing the
old thresholding limit into ->threshold_limit.
Make error_count read-only with the functionality to show the current
error count.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
We have rdmsr_on_cpu() now so remove locally defined solution in favor
of the generic one.
No functionality change.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
If one sets the threshold limit, say to 25:
$ echo 25 > machinecheck0/threshold_bank4/misc0/threshold_limit
and then reads it back again, it gives
$ cat machinecheck0/threshold_bank4/misc0/threshold_limit
19
which is actually 0x19 but we don't know that.
Make all output decimal.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Well, instead of having a real bank 4 on the BSP of each node and
symlinks on the remaining cores, we push it up into the amd_northbridge
descriptor which now contains a pointer to the northbridge bank 4
because the bank is one per northbridge and, as such, belongs in the NB
descriptor anyway.
Each time we hotplug CPUs, we use the northbridge pointer to copy the
shared bank into the per-CPU array of threshold_banks pointers, or
destroy it when the last CPU on the node goes offline, or create it when
the first comes online.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The code used to create a symlink on all non-BSP cores of a node when
the MCi_MISCj bank is present once per node. (This is generally the
case with bank 4 on AMD). However, these sysfs links cause a bunch
of problems with cpu off-/onlining testing and are, as such, a bit
overengineered. IOW, there's nothing wrong with having normal sysfs
files for the shared banks since the corresponding MSRs are replicated
across each core anyway.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
commit 82f7af09 ("x86/mce: Cleanup timer mess) dropped the
initialization of the per cpu timer interval. Duh :(
Restore the previous behaviour.
Reported-by: Chen Gong <gong.chen@linux.intel.com>
Cc: bp@amd64.org
Cc: tony.luck@intel.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use a more current logging style:
- Bare printks should have a KERN_<LEVEL> for consistency's sake
- Add pr_fmt where appropriate
- Neaten some macro definitions
- Convert some Ok output to OK
- Use "%s: ", __func__ in pr_fmt for summit
- Convert some printks to pr_<level>
Message output is not identical in all cases.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: levinsasha928@gmail.com
Link: http://lkml.kernel.org/r/1337655007.24226.10.camel@joe2Laptop
[ merged two similar patches, tidied up the changelog ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
In commit 82f7af09 (x86/mce: Cleanup timer mess), Thomas just forgot
the "/ 2" there while cleaning up.
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Use unsigned long for dealing with jiffies not int. Rename the
callback to something sensible. Use __this_cpu_read/write for
accessing per cpu data.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=kG4e
-----END PGP SIGNATURE-----
Merge tag 'x86-mce-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras
Pull x86/mce merge window patches from Tony Luck:
"Including two that make error_context() checks less sucky"
* tag 'x86-mce-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/ras/ras:
x86/mce: Add instruction recovery signatures to mce-severity table
x86/mce: Fix check for processor context when machine check was taken.
MCE: Fix vm86 handling for 32bit mce handler
x86/mce Add validation check before GHES error is recorded
x86/mce: Avoid reading every machine check bank register twice.
Instruction recovery cases are very similar to the data recovery one
we already have. Just trade out for a new MCACOD value.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Linus pointed out that there was no value is checking whether m->ip
was zero - because zero is a legimate value. If we have a reliable
(or faked in the VM86 case) "m->cs" we can use it to tell whether we
were in user mode or kernelwhen the machine check hit.
Reported-by: Linus Torvalds <torvalds@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When running on 32bit the mce handler could misinterpret
vm86 mode as ring 0. This can affect whether it does recovery
or not; it was possible to panic when recovery was actually
possible.
Fix this by always forcing vm86 to look like ring 3.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pull MCE updates from Ingo Molnar:
"This tree updates/fixes MCE hardware support, it makes the APIC LVT
thresholding interrupt optional because a subset of AMD F15h models
don't support it."
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, MCE, AMD: Disable error thresholding bank 4 on some models
x86, MCE, AMD: Hide interrupt_enable sysfs node
x86, MCE, AMD: Make APIC LVT thresholding interrupt optional
Got bitten again by the BIT() macro:
arch/x86/kernel/cpu/mcheck/mce.c: In function '__mcheck_cpu_apply_quirks':
arch/x86/kernel/cpu/mcheck/mce.c:1453:6: warning: left shift
count >= width of type arch/x86/kernel/cpu/mcheck/mce.c:1454:7: warning: left shift count >= width of type
Fix it already.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Frank Arnold <frank.arnold@amd.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1337684026-19740-2-git-send-email-bp@amd64.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull percpu updates from Tejun Heo:
"Contains Alex Shi's three patches to remove percpu_xxx() which overlap
with this_cpu_xxx(). There shouldn't be any functional change."
* 'for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: remove percpu_xxx() functions
x86: replace percpu_xxx funcs with this_cpu_xxx
net: replace percpu_xxx funcs with this_cpu_xxx or __this_cpu_xxx
Section 15.3.1.2 of the software developer manual has this to say about the
RIPV bit in the IA32_MCG_STATUS register:
RIPV (restart IP valid) flag, bit 0 — Indicates (when set) that program
execution can be restarted reliably at the instruction pointed to by the
instruction pointer pushed on the stack when the machine-check exception
is generated. When clear, the program cannot be reliably restarted at
the pushed instruction pointer.
We need to save the state of this bit in do_machine_check() and use it
in mce_notify_process() to force a signal; even if memory_failure() says
it made a complete recovery ... e.g. replaced a clean LRU page.
Acked-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Since percpu_xxx() serial functions are duplicated with this_cpu_xxx().
Removing percpu_xxx() definition and replacing them by this_cpu_xxx()
in code. There is no function change in this patch, just preparation for
later percpu_xxx serial function removing.
On x86 machine the this_cpu_xxx() serial functions are same as
__this_cpu_xxx() without no unnecessary premmpt enable/disable.
Thanks for Stephen Rothwell, he found and fixed a i386 build error in
the patch.
Also thanks for Andrew Morton, he kept updating the patchset in Linus'
tree.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Acked-by: Christoph Lameter <cl@gentwo.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Turn off MC4_MISC thresholding banks on models which have them but that
particular processor implementation does not supply applicable error
sources to be counted.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Depending on whether the box supports the APIC LVT interrupt for
thresholding, we want to show the 'interrupt_enable' sysfs node or not.
Make that the case by adding it to the default sysfs attributes only if
it is supported.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Currently, the APIC LVT interrupt for error thresholding is implicitly
enabled. However, there are models in the F15h range which do not enable
it. Make the code machinery which sets up the APIC interrupt support
an optional setting and add an ->interrupt_capable member to the bank
representation mirroring that capability and enable the interrupt offset
programming only if it is true.
Simplify code and fixup comment style while at it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
When GHES error record is logged into mcelog kernel buffer, a validation
check for physical address is necessary, which prevents reporting an
invalid physical address.
[Since physical address is the only useful element in this error record,
we drop generating the record completely if we don't have a valid address]
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reading machine check bank registers is slow. There is a trend of
increasing the number of banks, and the number of cores. The main section
of do_machine_check() is a serialized section where each cpu in turn
checks every bank. Even on a little two socket SandyBridge-EP system
that multiplies out as:
2 sockets * 8 cores * 2 hyperthreads * 20 banks = 640 MSRs
We already scan the banks in parallel in mce_no_way_out() to see if there
is a fatal error anywhere in the system. If we build a cache of VALID
bits during this scan, we can avoid uselessly re-reading banks that have
no data. Note that this cache is only a hint. If the valid bit is set in a
shared bank, all cpus that share that bank will see it during the parallel
scan, but the first to find it in the sequential scan will (usually) clear
the bank.
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Pull x86 "urgent" leftovers from Ingo Molnar:
"Pending x86/urgent bits that were not high prio enough to warrant
-rc-less v3.3-final inclusion."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: Fix pointer math issue in handle_ramdisks()
x86/ioapic: Add register level checks to detect bogus io-apic entries
x86, mce: Fix rcu splat in drain_mce_log_buffer()
x86, memblock: Move mem_hole_size() to .init
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPW8yUAAoJEHm+PkMAQRiGhFIH/RGUPxGmUkJv8EP5I4HDA4dJ
c6/PrzZCHs8rxzYzvn7ojXqZGXTOAA5ZgS9A6LkJ2sxMFvgMnkpFi6B4CwMzizS3
vLWo/HNxbiTCNGFfQrhQB8O58uNI8wOBa87lrQfkXkDqN0cFhdjtIxeY1BD9LXIo
qbWysGxCcZhJWHapsQ3NZaVJQnIK5vA/+mhyYP4HzbcHI3aWnbIEZ8GQKeY28Ch0
+pct5UQBjZavV5SujaW0Xd65oIiycm8XHAQw6FxQy//DfaabauWgFteR162Q/oew
xxUBDOHF3nO1bdteHHaYqxig0j1MbIHsqxTnE/neR8UryF04//1SFF7DYuY/1pg=
=SV5V
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc7' into x86/mce
Merge reason: Update from an ancient -rc1 base to an almost-final stable kernel.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Current kernel MCE code reads ERST at the first reading of /dev/mcelog
(maybe in starting mcelogd,) even if the system does not support ERST,
which results in a fake "no such device" message (as described in [1].)
This problem is not critical, but can confuse system admins.
This patch fixes it by filtering the return value from lower (ACPI) layer.
[1] http://thread.gmane.org/gmane.linux.kernel/1060250
Reported by: Jon Masters <jonathan@jonmasters.org>
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Huang Ying <ying.huang@intel.com>
Link: https://lkml.org/lkml/2012/1/23/299
Signed-off-by: Tony Luck <tony.luck@intel.com>
When I previously fixed up the mce_device code, I used a static array of
the pointers. It was (rightfully) pointed out to me that I should be
using the per_cpu code instead.
This patch converts the code over to that structure, moving the variable
back into the per_cpu area, like it used to be for 3.2 and earlier.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Link: https://lkml.org/lkml/2012/1/27/165
Signed-off-by: Tony Luck <tony.luck@intel.com>
141168c36c ("x86: Simplify code by removing a !SMP #ifdefs
from 'struct cpuinfo_x86'") removed a bunch of CONFIG_SMP ifdefs
around code touching struct cpuinfo_x86 members but also caused
the following build error with Randy's randconfigs:
mce_amd.c:(.cpuinit.text+0x4723): undefined reference to `cpu_llc_shared_map'
Restore the #ifdef in threshold_create_bank() which creates
symlinks on the non-BSP CPUs.
There's a better patch series being worked on by Kevin Winchester
which will solve this in a cleaner fashion, but that series is
too ambitious for v3.3 merging - so we first queue up this trivial
fix and then do the rest for v3.4.
Signed-off-by: Borislav Petkov <bp@alien8.de>
Acked-by: Kevin Winchester <kjwinchester@gmail.com>
Cc: Randy Dunlap <rdunlap@xenotime.net>
Cc: Nick Bowler <nbowler@elliptictech.com>
Link: http://lkml.kernel.org/r/20120203191801.GA2846@x1.osrc.amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Magic constants like 0x0134 in code just invite questions on
where they come from, what they mean, can they be changed.
Provide #defines for the architecturally defined MCACOD values
with a reference to the Intel Software Developers manual which
describes them.
Signed-off-by: Tony Luck <tony.luck@intel.com>
When suspending, there was a large list of warnings going something like:
Device 'machinecheck1' does not have a release() function, it is broken and must be fixed
This patch turns the static mce_devices into dynamically allocated, and
properly frees them when they are removed from the system. It solves
the warning messages on my laptop here.
Reported-by: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Tested-by: Djalal Harouni <tixxdz@opendz.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Borislav Petkov <bp@amd64.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 8a25a2fd12 ("cpu: convert 'cpu' and 'machinecheck' sysdev_class
to a regular subsystem") changed how things are dealt with in the MCE
subsystem. Some of the things that got broken due to this are CPU
hotplug and suspend/hibernate.
MCE uses per_cpu allocations of struct device. So, when a CPU goes
offline and comes back online, in order to ensure that we start from a
clean slate with respect to the MCE subsystem, zero out the entire
per_cpu device structure to 0 before using it.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Skip cpus with apic-ids >= 255 in !x2apic_mode
x86, x2apic: Allow "nox2apic" to disable x2apic mode setup by BIOS
x86, x2apic: Fallback to xapic when BIOS doesn't setup interrupt-remapping
x86, acpi: Skip acpi x2apic entries if the x2apic feature is not present
x86, apic: Add probe() for apic_flat
x86: Simplify code by removing a !SMP #ifdefs from 'struct cpuinfo_x86'
x86: Convert per-cpu counter icr_read_retry_count into a member of irq_stat
x86: Add per-cpu stat counter for APIC ICR read tries
pci, x86/io-apic: Allow PCI_IOAPIC to be user configurable on x86
x86: Fix the !CONFIG_NUMA build of the new CPU ID fixup code support
x86: Add NumaChip support
x86: Add x86_init platform override to fix up NUMA core numbering
x86: Make flat_init_apic_ldr() available
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Action required data path signature is defined in table 15-19 of SDM:
+-----------------------------------------------------------------------------+
| SRAR Error | Valid | OVER | UC | EN | MISCV | ADDRV | PCC | S | AR | MCACOD |
| Data Load | 1 | 0 | 1 | 1 | 1 | 1 | 0 | 1 | 1 | 0x134 |
+-----------------------------------------------------------------------------+
Recognise this, and pass MCE_AR_SEVERITY code back to do_machine_check() if
we have the action handler configured (CONFIG_MEMORY_FAILURE=y)
Acked-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
All non-urgent actions (reporting low severity errors and handling
"action-optional" errors) are now handled by a work queue. This
means that TIF_MCE_NOTIFY can be used to block execution for a
thread experiencing an "action-required" fault until we get all
cpus out of the machine check handler (and the thread that hit
the fault into mce_notify_process().
We use the new mce_{save,find,clear}_info() API to get information
from do_machine_check() to mce_notify_process(), and then use the
newly improved memory_failure(..., MF_ACTION_REQUIRED) to handle
the error (possibly signalling the process).
Update some comments to make the new code flows clearer.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Machine checks on Intel cpus interrupt execution on all cpus, regardless
of interrupt masking. We have a need to save some data about the cause
of the machine check (physical address) in the machine check handler that
can be retrieved later to attempt recovery in a more flexible execution
state.
Signed-off-by: Tony Luck <tony.luck@intel.com>
The MCI_STATUS_MISCV and MCI_STATUS_ADDRV bits in the bank status
registers define whether the MISC and ADDR registers respectively
contain valid data - provide a helper function to check these bits
and read the registers when needed.
In addition, processors that support software error recovery (as
indicated by the MCG_SER_P bit in the MCG_CAP register) may include
some undefined bits in the ADDR register - mask these out.
Acked-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There is only one caller of memory_failure(), all other users call
__memory_failure() and pass in the flags argument explicitly. The
lone user of memory_failure() will soon need to pass flags too.
Add flags argument to the callsite in mce.c. Delete the old memory_failure()
function, and then rename __memory_failure() without the leading "__".
Provide clearer message when action optional memory errors are ignored.
Acked-by: Borislav Petkov <bp@amd64.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This moves the 'cpu sysdev_class' over to a regular 'cpu' subsystem
and converts the devices to regular devices. The sysdev drivers are
implemented as subsystem interfaces now.
After all sysdev classes are ported to regular driver core entities, the
sysdev implementation will be entirely removed from the kernel.
Userspace relies on events and generic sysfs subsystem infrastructure
from sysdev devices, which are made available with this conversion.
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Borislav Petkov <bp@amd64.org>
Cc: Tigran Aivazian <tigran@aivazian.fsnet.co.uk>
Cc: Len Brown <lenb@kernel.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Several fields in struct cpuinfo_x86 were not defined for the
!SMP case, likely to save space. However, those fields still
have some meaning for UP, and keeping them allows some #ifdef
removal from other files. The additional size of the UP kernel
from this change is not significant enough to worry about
keeping up the distinction:
text data bss dec hex filename
4737168 506459 972040 6215667 5ed7f3 vmlinux.o.before
4737444 506459 972040 6215943 5ed907 vmlinux.o.after
for a difference of 276 bytes for an example UP config.
If someone wants those 276 bytes back badly then it should
be implemented in a cleaner way.
Signed-off-by: Kevin Winchester <kjwinchester@gmail.com>
Cc: Steffen Persvold <sp@numascale.com>
Link: http://lkml.kernel.org/r/1324428742-12498-1-git-send-email-kjwinchester@gmail.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
mce-inject provides a mechanism to simulate errors so that test
scripts can check for correct operation of the kernel without
requiring any specialized hardware to create rare events.
The existing code can simulate events in normal process context
and also in NMI context - but not in IRQ context. This patch
fills that gap.
Link: https://lkml.org/lkml/2011/12/7/537
Signed-off-by: Chen Gong <gong.chen@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Thermal throttle and power limit events are not defined as MCE errors in x86
architecture and should not generate MCE errors in mcelog.
Current kernel generates fake software defined MCE errors for these events.
This may confuse users because they may think the machine has real MCE errors
while actually only thermal throttle or power limit events happen.
To make it worse, buggy firmware on some platforms may falsely generate
the events. Therefore, kernel reports MCE errors which users think as real
hardware errors. Although the firmware bugs should be fixed, on the other hand,
kernel should not report MCE errors either.
So mcelog is not a good mechanism to report these events. To report the events, we count them in respective counters (core_power_limit_count,
package_power_limit_count, core_throttle_count, and package_throttle_count) in
/sys/devices/system/cpu/cpu#/thermal_throttle/. Users can check the counters
for each event on each CPU. Please note that all CPU's on one package report
duplicate counters. It's user application's responsibity to retrieve a package
level counter for one package.
This patch doesn't report package level power limit, core level power limit, and
package level thermal throttle events in mcelog. When the events happen, only
report them in respective counters in sysfs.
Since core level thermal throttle has been legacy code in kernel for a while and
users accepted it as MCE error in mcelog, core level thermal throttle is still
reported in mcelog. In the mean time, the event is counted in a counter in sysfs
as well.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: Borislav Petkov <bp@amd64.org>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/20111215001945.GA21009@linux-os.sc.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add a function which drains whatever MCEs were logged in already during
boot and before the decoder chains were registered.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
No functionality change, this is done so that in a follow-on patch all
queued-up MCEs can be decoded after registering on the chain.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Arjan would like to make struct file_operations const, but
mce-inject directly writes to the mce_chrdev_ops to install its
write handler. In an ideal world mce-inject would have its own
character device, but we have a sizable legacy of test scripts
that hardwire "/dev/mcelog", so it would be painful to switch to
a separate device now. Instead, this patch switches to a stub
function in the mce code, with a registration helper that
mce-inject can call when it is loaded.
Note that this would also allow for a sane process to allow
mce-inject to be unloaded again (with an unregister function,
and appropriate module_{get,put}() calls), but that is left for
potential future patches.
Reported-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4eb2e1971326651a3b@agluck-desktop.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
* 'linux_next' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-edac: (21 commits)
MAINTAINERS: add an entry for Edac Sandy Bridge driver
edac: tag sb_edac as EXPERIMENTAL, as it requires more testing
EDAC: Fix incorrect edac mode reporting in sb_edac
edac: sb_edac: Add it to the building system
edac: Add an experimental new driver to support Sandy Bridge CPU's
i7300_edac: Fix error cleanup logic
i7core_edac: Initialize memory name with cpu, channel, bank
i7core_edac: Fix compilation on 32 bits arch
i7core_edac: scrubbing fixups
EDAC: Correct Kconfig dependencies
i7core_edac: return -ENODEV if no MC is found
i7core_edac: use edac's own way to print errors
MAINTAINERS: remove dropped edac_mce.* from the file
i7core_edac: Drop the edac_mce facility
x86, MCE: Use notifier chain only for MCE decoding
EDAC i7core: Use mce socketid for better compatibility
i7core_edac: Don't enable memory scrubbing for Xeon 35xx
i7core_edac: Add scrubbing support
edac: Move edac main structs to include/linux/edac.h
i7core_edac: Fix oops when trying to inject errors
...
Remove edac_mce pieces and use the normal MCE decoder notifier chain by
retaining the same functionality with considerably less code.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
These files were implicitly getting EXPORT_SYMBOL via device.h
which was including module.h, but that will be fixed up shortly.
By fixing these now, we can avoid seeing things like:
arch/x86/kernel/rtc.c:29: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
arch/x86/kernel/pci-dma.c:20: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL’
arch/x86/kernel/e820.c:69: warning: type defaults to ‘int’ in declaration of ‘EXPORT_SYMBOL_GPL’
[ with input from Randy Dunlap <rdunlap@xenotime.net> and also
from Stephen Rothwell <sfr@canb.auug.org.au> ]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Drop the edac_mce custom hook in favor of the generic notifier
mechanism. Also, do not log the error to mcelog if the notified agent
was able to decode it.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode, AMD: Add microcode revision to /proc/cpuinfo
x86, microcode: Correct microcode revision format
coretemp: Get microcode revision from cpu_data
x86, intel: Use c->microcode for Atom errata check
x86, intel: Output microcode revision in /proc/cpuinfo
x86, microcode: Don't request microcode from userspace unnecessarily
Fix up trivial conflicts in arch/x86/kernel/cpu/amd.c (conflict between
moving AMD BSP code to cpu_dev helper function and adding AMD microcode
revision to /proc/cpuinfo code)
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (121 commits)
perf symbols: Increase symbol KSYM_NAME_LEN size
perf hists browser: Refuse 'a' hotkey on non symbolic views
perf ui browser: Use libslang to read keys
perf tools: Fix tracing info recording
perf hists browser: Elide DSO column when it is set to just one DSO, ditto for threads
perf hists: Don't consider filtered entries when calculating column widths
perf hists: Don't decay total_period for filtered entries
perf hists browser: Honour symbol_conf.show_{nr_samples,total_period}
perf hists browser: Do not exit on tab key with single event
perf annotate browser: Don't change selection line when returning from callq
perf tools: handle endianness of feature bitmap
perf tools: Add prelink suggestion to dso update message
perf script: Fix unknown feature comment
perf hists browser: Apply the dso and thread filters when merging new batches
perf hists: Move the dso and thread filters from hist_browser
perf ui browser: Honour the xterm colors
perf top tui: Give color hints just on the percentage, like on --stdio
perf ui browser: Make the colors configurable and change the defaults
perf tui: Remove unneeded call to newtCls on startup
perf hists: Don't format the percentage on hist_entry__snprintf
...
Fix up conflicts in arch/x86/kernel/kprobes.c manually.
Ingo's tree did the insane "add volatile to const array", which just
doesn't make sense ("volatile const"?). But we could remove the const
*and* make the array volatile to make doubly sure that gcc doesn't
optimize it away..
Also fix up kernel/trace/ring_buffer.c non-data-conflicts manually: the
reader_lock has been turned into a raw lock by the core locking merge,
and there was a new user of it introduced in this perf core merge. Make
sure that new use also uses the raw accessor functions.
506ed6b53e ("x86, intel: Output microcode revision in /proc/cpuinfo")
added microcode revision format to /proc/cpuinfo and the MCE handler in
decimal format but both AMD and Intel patch levels are handled as hex
numbers. Fix it.
Acked-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
I got a request to make it easier to determine the microcode
update level on Intel CPUs. This patch adds a new "microcode"
field to /proc/cpuinfo.
The microcode level is also outputed on fatal machine checks
together with the other CPUID model information.
I removed the respective code from the microcode update driver,
it just reads the field from cpu_data. Also when the microcode
is updated it fills in the new values too.
I had to add a memory barrier to native_cpuid to prevent it
being optimized away when the result is not used.
This turns out to clean up further code which already got this
information manually. This is done in followon patches.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Link: http://lkml.kernel.org/r/1318466795-7393-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Just convert all the files that have an nmi handler to the new routines.
Most of it is straight forward conversion. A couple of places needed some
tweaking like kgdb which separates the debug notifier from the nmi handler
and mce removes a call to notify_die.
[Thanks to Ying for finding out the history behind that mce call
https://lkml.org/lkml/2010/5/27/114
And Boris responding that he would like to remove that call because of it
https://lkml.org/lkml/2011/9/21/163]
The things that get converted are the registeration/unregistration routines
and the nmi handler itself has its args changed along with code removal
to check which list it is on (most are on one NMI list except for kgdb
which has both an NMI routine and an NMI Unknown routine).
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Corey Minyard <minyard@acm.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Jack Steiner <steiner@sgi.com>
Link: http://lkml.kernel.org/r/1317409584-23662-4-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
del_timer_sync() can cause a deadlock when called in interrupt context.
It is used with on_each_cpu() in some parts for sysfs files like bank*,
check_interval, cmci_disabled and ignore_ce.
However, use of on_each_cpu() results in calling the function passed
as the argument in interrupt context. This causes a flood of nested
warnings from del_timer_sync() (it runs on each CPU) caused even by a
simple file access like:
$ echo 300 > /sys/devices/system/machinecheck/machinecheck0/check_interval
Fortunately, these MCE-specific files are rarely used and AFAIK only few
MCE geeks experience this warning.
To remove the warning, move timer deletion outside of the interrupt
context.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The cmci_discover_lock can be taken in atomic context (cpu bring
up sequence) and therefore cannot be preempted on -rt.
In mainline this change documents the low level nature of
the lock - otherwise there's no functional difference. Lockdep
and Sparse checking will work as usual.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are many functions named mce_* so use a new prefix for the subset
of functions related to sysfs support.
And since f3c6ea1b06 introduces
syscore_ops, use the prefix mce_syscore for some functions related to
power management which were in sysdev_class before.
Before: After:
mce_device mce_sysdev
mce_sysclass mce_sysdev_class
mce_attrs mce_sysdev_attrs
mce_dev_initialized mce_sysdev_initialized
mce_create_device mce_sysdev_create
mce_remove_device mce_sysdev_remove
mce_suspend mce_syscore_suspend
mce_shutdown mce_syscore_shutdown
mce_resume mce_syscore_resume
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED81B.8020506@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
There are many functions named mce_* so use a new prefix for the subset
of functions dealing with the character device /dev/mcelog.
This change doesn't impact the mce-inject module because the exported
symbol mce_chrdev_ops already has the prefix, therefore it is left
unchanged.
Before: After:
mce_wait mce_chrdev_wait
mce_state_lock mce_chrdev_state_lock
open_count mce_chrdev_open_count
open_exclu mce_chrdev_open_exclu
mce_open mce_chrdev_open
mce_release mce_chrdev_release
mce_read_mutex mce_chrdev_read_mutex
mce_read mce_chrdev_read
mce_poll mce_chrdev_poll
mce_ioctl mce_chrdev_ioctl
mce_log_device mce_chrdev_device
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED7CD.3040500@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Use a temporary local variable m to simplify the code. No change in
logic.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED7A8.8020307@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Use temporary local variable sysdev to simplify the code. No change in
logic.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED777.7080205@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Because "ancient CPUs" like p5 and winchip don't have X86_FEATURE_MCA
(I suppose so), mcheck_cpu_init() on such CPUs will return at check of
mce_available() after __mcheck_cpu_ancient_init().
It is hard to know this implicit behavior without knowing the CPUs
well. So make it clear that we leave mcheck_cpu_init() when the CPU is
initialized in __mcheck_cpu_ancient_init().
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED74B.20502@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
This patch introduces mce_gather_info() which is to be called at the
beginning of error handling and gathers minimum error information from
proper error registers (and saved registers).
As the result of mce_get_rip() is integrated, unnecessary zeroing
is removed. This also takes care of saving RIP which is required to
make some decision about error severity for SRAR errors, instead of
retrieving it later in the handler.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED71A.1060906@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The MCE handler uses a special vector for self IPI to invoke
post-emergency processing in an interrupt context, e.g. call an
NMI-unsafe function, wakeup loggers, schedule time-consuming work for
recovery, etc.
This mechanism is now generalized by the following commit:
> e360adbe29
> Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
> Date: Thu Oct 14 14:01:34 2010 +0800
>
> irq_work: Add generic hardirq context callbacks
>
> Provide a mechanism that allows running code in IRQ context. It is
> most useful for NMI code that needs to interact with the rest of the
> system -- like wakeup a task to drain buffers.
:
So change to use provided generic mechanism.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED6B2.6080005@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
More specifically:
- sort bits in the macros
- use BITCLR/BITSET
- coordinate message pattern
- use m for struct mce
- cleanup for severities_debugfs_init()
No functional change.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED679.9090503@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The current format of an item in this table is:
condition(param, ..., level, message [, condition2 ...])
So we have to check both an item's head and tail to find the conditions
which match the item.
Format them in a more straight forward manner:
item(level, message, condition [, condition2 ...])
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED61F.5010502@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The table looks very complicated and hard to read for people other than
skilled developers. So let's clean it up a bit. At first, change format
to ease reading elements in the table.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Link: http://lkml.kernel.org/r/4DEED5EB.6050400@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
The "Spurious not enabled" entry is redundant: the "Not enabled" entry
earlier in the table will cover this case.
The "Action required; unknown MCACOD" entry shouldn't specify MCACOD in
the .mask field. Current code will only match for mcacod==0 rather than
all AR=1 entries.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Link: http://lkml.kernel.org/r/4DEED5BC.8030703@jp.fujitsu.com
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (50 commits)
x86, mm: Allow ZONE_DMA to be configurable
x86, NUMA: Trim numa meminfo with max_pfn in a separate loop
x86, NUMA: Rename setup_node_bootmem() to setup_node_data()
x86, NUMA: Enable emulation on 32bit too
x86, NUMA: Enable CONFIG_AMD_NUMA on 32bit too
x86, NUMA: Rename amdtopology_64.c to amdtopology.c
x86, NUMA: Make numa_init_array() static
x86, NUMA: Make 32bit use common NUMA init path
x86, NUMA: Initialize and use remap allocator from setup_node_bootmem()
x86-32, NUMA: Add @start and @end to init_alloc_remap()
x86, NUMA: Remove long 64bit assumption from numa.c
x86, NUMA: Enable build of generic NUMA init code on 32bit
x86, NUMA: Move NUMA init logic from numa_64.c to numa.c
x86-32, NUMA: Update numaq to use new NUMA init protocol
x86-32, NUMA: Replace srat_32.c with srat.c
x86-32, NUMA: implement temporary NUMA init shims
x86, NUMA: Move numa_nodes_parsed to numa.[hc]
x86-32, NUMA: Move get_memcfg_numa() into numa_32.c
x86, NUMA: make srat.c 32bit safe
x86, NUMA: rename srat_64.c to srat.c
...
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, efi: Ensure that the entirity of a region is mapped
x86, efi: Pass a minimal map to SetVirtualAddressMap()
x86, efi: Merge contiguous memory regions of the same type and attribute
x86, efi: Consolidate EFI nx control
x86, efi: Remove virtual-mode SetVirtualAddressMap call
* 'x86-gart-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, gart: Don't enforce GART aperture lower-bound by alignment
* 'x86-irq-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Don't unmask disabled irqs when migrating them
x86: Skip migrating IRQF_PER_CPU irqs in fixup_irqs()
* 'x86-mce-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, mce: Drop the default decoding notifier
x86, MCE: Do not taint when handling correctable errors
This patch fixes a bug reported by a customer, who found
that many unreasonable error interrupts reported on all
non-boot CPUs (APs) during the system boot stage.
According to Chapter 10 of Intel Software Developer Manual
Volume 3A, Local APIC may signal an illegal vector error when
an LVT entry is set as an illegal vector value (0~15) under
FIXED delivery mode (bits 8-11 is 0), regardless of whether
the mask bit is set or an interrupt actually happen. These
errors are seen as error interrupts.
The initial value of thermal LVT entries on all APs always reads
0x10000 because APs are woken up by BSP issuing INIT-SIPI-SIPI
sequence to them and LVT registers are reset to 0s except for
the mask bits which are set to 1s when APs receive INIT IPI.
When the BIOS takes over the thermal throttling interrupt,
the LVT thermal deliver mode should be SMI and it is required
from the kernel to keep AP's LVT thermal monitoring register
programmed as such as well.
This issue happens when BIOS does not take over thermal throttling
interrupt, AP's LVT thermal monitor register will be restored to
0x10000 which means vector 0 and fixed deliver mode, so all APs will
signal illegal vector error interrupts.
This patch check if interrupt delivery mode is not fixed mode before
restoring AP's LVT thermal monitor register.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Yong Wang <yong.y.wang@intel.com>
Cc: hpa@linux.intel.com
Cc: joe@perches.com
Cc: jbaron@redhat.com
Cc: trenn@suse.de
Cc: kent.liu@intel.com
Cc: chaohong.guo@intel.com
Cc: <stable@kernel.org> # As far back as possible
Link: http://lkml.kernel.org/r/1303402963-17738-1-git-send-email-youquan.song@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
b may be added to a list, but is not removed before being freed
in the case of an error. This is done in the corresponding
deallocation function, so the code here has been changed to
follow that.
The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E,E1,E2;
identifier l;
@@
*list_add(&E->l,E1);
... when != E1
when != list_del(&E->l)
when != list_del_init(&E->l)
when != E = E2
*kfree(E);// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1305294731-12127-1-git-send-email-julia@diku.dk
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The default notifier doesn't make a lot of sense to call in the
correctable errors case. Drop it and emit the mcelog decoding
hint only in the uncorrectable errors case and when no notifier
is registered. Also, limit issuing the "mcelog --ascii" message
in the rare case when we dump unreported CEs before panicking.
While at it, remove unused old x86_mce_decode_callback from the
header.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Nagananda Chumbalkar <Nagananda.Chumbalkar@hp.com>
Cc: Russ Anderson <rja@sgi.com>
Link: http://lkml.kernel.org/r/20110420102349.GB1361@aftab
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Correctable errors are considered something rather normal on
modern hardware these days. Even more importantly, correctable
errors mean exactly that - they've been corrected by the
hardware - and there's no need to taint the kernel since
execution hasn't been compromised so far.
Also, drop tainting in the thermal throttling code for a similar
reason: crossing a thermal threshold does not mean corruption.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Nagananda Chumbalkar <Nagananda.Chumbalkar@hp.com>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Russ Anderson <rja@sgi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1303135222-17118-1-git-send-email-bp@amd64.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The MCE subsystem needs to sample an RCU-protected index outside of
any protection for that index. If this was a pointer, we would use
rcu_access_pointer(), but there is no corresponding rcu_access_index().
This commit therefore creates an rcu_access_index() and applies it
to MCE.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Zdenek Kabelac <zkabelac@redhat.com>
It is more effective to use a segment prefix instead of calculating the
address of the current cpu area amd then testing flags.
Signed-off-by: Christoph Lameter <cl@linux.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
* 'syscore' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
Introduce ARCH_NO_SYSDEV_OPS config option (v2)
cpufreq: Use syscore_ops for boot CPU suspend/resume (v2)
KVM: Use syscore_ops instead of sysdev class and sysdev
PCI / Intel IOMMU: Use syscore_ops instead of sysdev class and sysdev
timekeeping: Use syscore_ops instead of sysdev class and sysdev
x86: Use syscore_ops instead of sysdev classes and sysdevs
Some subsystems in the x86 tree need to carry out suspend/resume and
shutdown operations with one CPU on-line and interrupts disabled and
they define sysdev classes and sysdevs or sysdev drivers for this
purpose. This leads to unnecessarily complicated code and excessive
memory usage, so switch them to using struct syscore_ops objects for
this purpose instead.
Generally, there are three categories of subsystems that use
sysdevs for implementing PM operations: (1) subsystems whose
suspend/resume callbacks ignore their arguments entirely (the
majority), (2) subsystems whose suspend/resume callbacks use their
struct sys_device argument, but don't really need to do that,
because they can be implemented differently in an arguably simpler
way (io_apic.c), and (3) subsystems whose suspend/resume callbacks
use their struct sys_device argument, but the value of that argument
is always the same and could be ignored (microcode_core.c). In all
of these cases the subsystems in question may be readily converted to
using struct syscore_ops objects for power management and shutdown.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
APEI ERST firmware interface and implementation has no multiple users
in mind. For example, if there is four records in storage with ID: 1,
2, 3 and 4, if two ERST readers enumerate the records via
GET_NEXT_RECORD_ID as follow,
reader 1 reader 2
1
2
3
4
-1
-1
where -1 signals there is no more record ID.
Reader 1 has no chance to check record 2 and 4, while reader 2 has no
chance to check record 1 and 3. And any other GET_NEXT_RECORD_ID will
return -1, that is, other readers will has no chance to check any
record even they are not cleared by anyone.
This makes raw GET_NEXT_RECORD_ID not suitable for used by multiple
users.
To solve the issue, an in-memory ERST record ID cache is designed and
implemented. When enumerating record ID, the ID returned by
GET_NEXT_RECORD_ID is added into cache in addition to be returned to
caller. So other readers can check the cache to get all record ID
available.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
They were generated by 'codespell' and then manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: trivial@kernel.org
LKML-Reference: <1300389856-1099-3-git-send-email-lucas.demarchi@profusion.mobi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
cpu_info is already with per_cpu, We can take llc_shared_map out
of cpu_info, and declare it as per_cpu variable directly.
So later referencing could be simple and directly instead of
diving to find cpu_info at first.
Also could make smp_store_cpu_info() much simple to avoid to do
save and restore trick.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Hans Rosenfeld <hans.rosenfeld@amd.com>
Cc: Alok N Kataria <akataria@vmware.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Hans J. Koch <hjk@linutronix.de>
Cc: Tejun Heo <tj@kernel.org>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <4D3A16E8.5020608@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In therm_throt.c, commit
9e76a97efd patch doesn't export
the symbol platform_thermal_notify.
Other drivers (e.g. drivers/hwmon/coretemp.c) can not find the
symbol platform_thermal_notify when defining threshould
interrupt handler.
Please apply this patch to allow threshold interrupt handler in
coretemp.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Cc: R Durgadoss <durgadoss.r@intel.com>
Cc: khali@linux-fr.org <khali@linux-fr.org>
Cc: lm-sensors@lm-sensors.org <lm-sensors@lm-sensors.org>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
LKML-Reference: <20110121041239.GB26954@linux-os.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (30 commits)
gameport: use this_cpu_read instead of lookup
x86: udelay: Use this_cpu_read to avoid address calculation
x86: Use this_cpu_inc_return for nmi counter
x86: Replace uses of current_cpu_data with this_cpu ops
x86: Use this_cpu_ops to optimize code
vmstat: User per cpu atomics to avoid interrupt disable / enable
irq_work: Use per cpu atomics instead of regular atomics
cpuops: Use cmpxchg for xchg to avoid lock semantics
x86: this_cpu_cmpxchg and this_cpu_xchg operations
percpu: Generic this_cpu_cmpxchg() and this_cpu_xchg support
percpu,x86: relocate this_cpu_add_return() and friends
connector: Use this_cpu operations
xen: Use this_cpu_inc_return
taskstats: Use this_cpu_ops
random: Use this_cpu_inc_return
fs: Use this_cpu_inc_return in buffer.c
highmem: Use this_cpu_xx_return() operations
vmstat: Use this_cpu_inc_return for vm statistics
x86: Support for this_cpu_add, sub, dec, inc_return
percpu: Generic support for this_cpu_add, sub, dec, inc_return
...
Fixed up conflicts: in arch/x86/kernel/{apic/nmi.c, apic/x2apic_uv_x.c, process.c}
as per Tejun.
With priorities in place and no one really understanding the difference between
DIE_NMI and DIE_NMI_IPI, just remove DIE_NMI_IPI and convert everyone to DIE_NMI.
This also simplifies default_do_nmi() a little bit. Instead of calling the
die_notifier in both the if and else part, just pull it out and call it before
the if-statement. This has the side benefit of avoiding a call to the ioport
to see if there is an external NMI sitting around until after the (more frequent)
internal NMIs are dealt with.
Patch-Inspired-by: Huang Ying <ying.huang@intel.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1294348732-15030-5-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In order to consolidate the NMI die_chain events, we need to setup the priorities
for the die notifiers.
I started by defining a bunch of common priorities that can be used by the
notifier blocks. Then I modified the notifier blocks to use the newly created
priorities.
Now that the priorities are straightened out, it should be easier to remove the
event DIE_NMI_IPI.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1294348732-15030-4-git-send-email-dzickus@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-alternatives-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, suspend: Avoid unnecessary smp alternatives switch during suspend/resume
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-64, asm: Use fxsaveq/fxrestorq in more places
* 'x86-hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, hwmon: Add core threshold notification to therm_throt.c
* 'x86-paravirt-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, paravirt: Use native_halt on a halt, not native_safe_halt
* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
locking, lockdep: Convert sprintf_symbol to %pS
* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
irq: Better struct irqaction layout
This patch adds code to therm_throt.c to notify core thermal threshold
events. These thresholds are supported by the IA32_THERM_INTERRUPT register.
The status/log for the same is monitored using the IA32_THERM_STATUS register.
The necessary #defines are in msr-index.h. A call back is added to mce.h, to
further notify the thermal stack, about the threshold events.
Signed-off-by: Durgadoss R <durgadoss.r@intel.com>
LKML-Reference: <D6D887BA8C9DFF48B5233887EF04654105C1251710@bgsmsx502.gar.corp.intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Replace all uses of current_cpu_data with this_cpu operations on the
per cpu structure cpu_info. The scala accesses are replaced with the
matching this_cpu ops which results in smaller and more efficient
code.
In the long run, it might be a good idea to remove cpu_data() macro
too and use per_cpu macro directly.
tj: updated description
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
Go through x86 code and replace __get_cpu_var and get_cpu_var
instances that refer to a scalar and are not used for address
determinations.
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Signed-off-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch reworks and cleans up mce_amd_feature_init() by
introducing helper functions to setup and check the LVT offset.
It also fixes line endings in pr_err() calls.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1288015419-29543-4-git-send-email-robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>