Pausing a decoder followed by a Play command would do nothing. Fixed.
Pausing a decoder running at non-standard speed following by a Continue
would reset the speed to 100%. Fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
s_register was assigning the return code to (unsigned)reg->val, rather than
errCode, which it what it would return. Except reg->val can't be < 0, so it
would never actually return an error.
g_register never actually put the value it read into reg->val.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Various gpio and mux settings for the Osprey 440 weren't correct. Fix them
and provide some documentation about how the gpios work.
The osprey eeprom routine wasn't run for the 440, add it. It was also crap,
re-written to be better.
Add the Osprey 440 to the Bt878 ALSA driver's whitelist. Currently the sample
rate is fixed at 32kHz, as the driver doesn't support different rates for
digital input mode, though the card can select the rate from 32, 44.1, or 48
kHz via gpio.
Setting the audio gain via ALSA isn't supported yet; a userspace tool that
programs the X9221 via i2c-dev must be used.
The Bt878 digital audio format isn't programmed correctly for the CS5331A ADC
used, resulting in extremely garbled sound. That is fixed in a followup
patch.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
linux/dvb/video.h uses types __u32, __s32, etc., but does not include
any header defining those when __KERNEL__ is not defined.
Fix this by including asm/types.h when __KERNEL__ is not defined.
Signed-off-by: Anssi Hannula <anssi.hannula@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When raw capture was turned off, the current capturing frame (v4l_grab_frame)
wasn't reset to NO_GRAB_ACTIVE. If capture was turned back on, the driver
would think this frame was currently being captured, and wait for it to
complete before starting a new frame. The hardware on the other hand would
not be actively capturing a frame. The result was the driver would wait
forever for v4l_grab_frame to be captured.
Some calls to zr36057_set_memgrab(0) were missing spin-locks, which have been
added.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the UYVY and the other big endian output formats. The
driver was naming formats based on the host endianess. This is different
that all the other drivers appear to work and not what software appears
to expect.
Use ARRAY_SIZE() to find the the size of the zoran_formats array.
Change the way the driver handles setting the video format register. Rather
than use some if and switch statements to set to register by looking at the
format id, the format list simply has a field with the proper bits to set.
Adds a bit of ifdef to make a driver without V4L1 support more possible.
Also create a macro for defining formats that handles vl41 and/or vl42
support to avoid repeated ifdefs in the format list.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver was returning the size of the (fixed) buffer it allocated as the
sizeimage field in the v4l2 pixel format, rather than the actual size of the
image. For example, a 192x128 YUYV image is 49152 bytes but the driver would
always return 131072 bytes since if that was the size of the v4l buffer.
This violates the v4l2 spec, which says that sizeimage should be the actual
size of the image for uncompressed formats. It also caused mplayer to crash.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
During uncompressed capture, the poll() function was looking the wrong frame.
It was using the frame the driver was going to capture into next (pend_tail),
when it should have been looking at the next frame to be de-queued with
DQBUF/SYNC (sync_tail).
It also wasn't looking in the right spot. It was looking at the file handle's
copy of the buffer status, rather than the driver core copy. The interrupt
routine marks frames as done in the driver core copy, the file handle copy
isn't updated. So even if poll() looked at the right frame, it would never
see it transition to done and return POLLIN.
The compressed capture code has this same problem, looking in fh->jpg_buffers
when it should have used zr->jpg_buffers.
There was some logic to detect when there was no current capture in process
nor any frames queued and try to return an error, which ends up being a bad
idea. It's possible to call select() from one thread while no capture is in
process, or no frames queued, and then start a capture or queue frames from
another thread.
The buffer state variables are protected by a spin lock, which the code wasn't
acquiring. That is fixed too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The zr36067 driver doesn't make a distinction between the different sub-types
of NTSC, PAL, or SECAM norms. For example, when the enum std ioctl returns
the PAL standard it returns PAL_BG|PAL_DK|PAL_H|PAL_I.
When setting the norm, it required the bitmask to match exactly the set of
norms used during the enumeration. If just one norm was specified, for
example PAL_BG or NTSC_M, it would fail. This violates the V4L2 spec,
"VIDIOC_S_STD accepts *one* or more flags..."
The key thing to realize is that V4L2_STD_PAL is not one bit, it is multiple
bits. It's ok to call S_STD with any *one* of those bits, but the driver was
requiring *all* of them.
This fixes the S_STD function so that it will accept any set of one or more
PAL norms as PAL, and the same for NTSC and SECAM.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
While I was busy compile-testing my patch, ENOSYS sneaked into pm.h
leading to some compile-breakages mostly on ia64 and some mips configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We ClearSlabDebug() before the last SlabDebug() check. Clear it later.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Ingo noticed that the SLUB code does include the lock debugging free
check.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix show_stack() when stack argument is NULL.
[SPARC]: Fix serial console node string creation.
[SPARC]: Mark SBUS framebuffer ioctls as IGNORE in compat_ioctl.c
[SPARC64]: asm-sparc64/floppy.h needs linux/pci.h
[SPARC64]: Fix conflicts in SBUS/PCI/EBUS/ISA DMA handling.
[VIDEO]: Fix OOPS in all SBUS framebuffer drivers.
[SPARC64]: Handle mostek clock type in mini_rtc driver.
[PARTITION]: Sun/Solaris VTOC table corrections
[SPARC]: Fix floppy on some sun4c systems.
[SPARC64]: Fix sun4u PCI config space accesses on sun4u.
[PARTITION] MSDOS: Fix Sun num_partitions handling.
[SPARC]: Update defconfig.
Commit 296699de6b broke building APM
support if CONFIG_PM_SLEEP is not set.
Reported by Toralf Förster <toralf.foerster@gmx.de>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[ Simplified a bit as suggested by Rafael. -Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the m32r build after the commit "Remove fs.h from mm.h"
was merged (commit 4e950f6f01).
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Added code to recognize the second interface on M5275 boards.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On the MCF5272, there is no need to read the ICR before writing it :
the bit 4n+3 is a write-enable for the bits 4n,4n+1 and 4n+2.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix the work queue code in the FEC driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removed unused CONFIG symbol and its conditional code from FEC driver.
Pointed out by Robert P. J. Day <rpjday@mindspring.com>.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include cacheflush.h to get definitions for cache functions used
in this code.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It didn't handle that case at all, and now dump_stack()
can be implemented directly as show_stack(current, NULL)
Signed-off-by: David S. Miller <davem@davemloft.net>
The string setting code depends upon the original value of the
"skip" variable, not the one that gets modified by the node
traversal loop.
Based upon a patch by Mark Fortescue.
Signed-off-by: David S. Miller <davem@davemloft.net>
They are handled in a ->compat_ioctl() handler, so it's just noise
when compat_ioctl.c warns which occurs when they are used on non-SBUS
framebuffer devices.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fully unify all of the DMA ops so that subordinate bus types to
the DMA operation providers (such as ebus, isa, of_device) can
work transparently.
Basically, we just make sure that for every system device we
create, the dev->archdata 'iommu' and 'stc' fields are filled
in.
Then we have two platform variants of the DMA ops, one for SUN4U which
actually programs the real hardware, and one for SUN4V which makes
hypervisor calls.
This also fixes the crashes in parport_pc on sparc64, reported by
Meelis Roos.
Signed-off-by: David S. Miller <davem@davemloft.net>
All of these drivers use a silly:
struct all_info {
struct fb_info info;
struct foo_par par;
};
struct all_info *all = kzalloc(sizeof(*all), GFP_KERNEL);
all->info.par = &all->par;
etc. etc. code sequence, basically replicating the provided
framebuffer_alloc()/framebuffer_release(), and doing it badly.
Not only is this massive code duplication, it also caused a
bug in that we weren't setting the fb_info->device pointer
which results in an OOPS when fb_is_primary_device() runs.
Fix all of this by using framebuffer_{alloc,release}() and
passing in "&of_device->dev" as the device pointer.
Signed-off-by: David S. Miller <davem@davemloft.net>
Start doing VTOC validation before using its contents.
The validation is adjusted so as not to break existing setups
that do not set the VTOC version, sanity and partition count entries.
VTOC tables with more than 8 partitions will NOT be used.
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add in code to support an 82077 FDC on sun4c systems. There is a
problem with spurious interrupts but it does apear to work.
Testing on my SS2 (82072A FDC) shows that the floppy driver is not
100% with sun4c any way (any spurious interrupt kills it, requiring a
reboot to recover).
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't provide fake PCI config space for sun4u.
Also, put back the funny host controller space handling that
at least Sabre needs. You have to read PCI host controller
registers at their nature size otherwise you get zeros instead
of correct values.
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the Solaris x86 number of partitions (slices) is a way that is
backward compatible with the earlier size.
This works without a new VTOC structure definition as the timestamp
and v_asciilabel fields in the VTOC are not used by the kernel yet.
Signed-off-by: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gabriel C reports lguest doesn't compile with CONFIG_BLOCK=n. Fix this
by introducing a config var for the block device, which depends on
LGUEST && BLOCK. Do the same for the net driver, rather then depending
gratuitously on CONFIG_NET.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: (28 commits)
[SCSI] mpt fusion: Changes in mptctl.c for logging support
[SCSI] mpt fusion: Changes in mptfc.c mptlan.c mptsas.c and mptspi.c for logging support
[SCSI] mpt fusion: Changes in mptscsih.c for logging support
[SCSI] mpt fusion: Changes in mptbase.c for logging support
[SCSI] mpt fusion: logging support in Kconfig, Makefile, mptbase.h and addition of mptdebug.h
[SCSI] libsas: Fix potential NULL dereference in sas_smp_get_phy_events()
[SCSI] bsg: Fix build for CONFIG_BLOCK=n
[SCSI] aacraid: fix Sunrise Lake reset handling
[SCSI] aacraid: add SCSI SYNCHONIZE_CACHE range checking
[SCSI] add easyRAID to the no report luns blacklist
[SCSI] advansys: lindent and other large, uninteresting changes
[SCSI] aic79xx, aic7xxx: Fix incorrect width setting
[SCSI] qla2xxx: fix to honor ignored parameters in sysfs attributes
[SCSI] aacraid: draw line in sand, sundry cleanup and version update
[SCSI] iscsi_tcp: Turn off bounce buffers
[SCSI] libiscsi: fix cmd seqeunce number checking
[SCSI] iscsi_tcp, ib_iser Enable module refcounting for iscsi host template
[SCSI] libiscsi: make sure session is not blocked when removing host
[SCSI] libsas: Remove PCI dependencies
[SCSI] simscsi: convert to use the data buffer accessors
...
Restore the 2.6.22 CONFIG_ACPI_SLEEP build option, but now shadowing the
new CONFIG_PM_SLEEP option.
Signed-off-by: Len Brown <len.brown@intel.com>
[ Modified to work with the PM config setup changes. ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce CONFIG_SUSPEND representing the ability to enter system sleep
states, such as the ACPI S3 state, and allow the user to choose SUSPEND
and HIBERNATION independently of each other.
Make HOTPLUG_CPU be selected automatically if SUSPEND or HIBERNATION has
been chosen and the kernel is intended for SMP systems.
Also, introduce CONFIG_PM_SLEEP which is automatically selected if
CONFIG_SUSPEND or CONFIG_HIBERNATION is set and use it to select the
code needed for both suspend and hibernation.
The top-level power management headers and the ACPI code related to
suspend and hibernation are modified to use the new definitions (the
changes in drivers/acpi/sleep/main.c are, mostly, moving code to reduce
the number of ifdefs).
There are many other files in which CONFIG_PM can be replaced with
CONFIG_PM_SLEEP or even with CONFIG_SUSPEND, but they can be updated in
the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace CONFIG_SOFTWARE_SUSPEND with CONFIG_HIBERNATION to avoid
confusion (among other things, with CONFIG_SUSPEND introduced in the
next patch).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make sure declarations stay in sync with definitions by keeping all
extern declarations in common .h files.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
A non-periodic clock_event_device and the "jiffies" clock don't mix well:
tick_handle_periodic() can go into an infinite loop.
Currently lguest guests use the jiffies clock when the TSC is
unusable. Instead, make the Host write the current time into the lguest
page on every interrupt. This doesn't cost much but is more precise
and at least as accurate as the jiffies clock. It also gets rid of
the GET_WALLCLOCK hypercall.
Also, delay setting sched_clock until our clock is set up, otherwise
the early printk timestamps can go backwards (not harmful, just ugly).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jason Yeh sent his crashing .config: bzImages made with
CONFIG_RELOCATABLE=y put the relocs where the BSS is expected, and we
crash with unusual results such as:
lguest: unhandled trap 14 at 0xc0122ae1 (0xa9)
Relying on BSS being zero was merely laziness on my part, and
unfortunately, lguest doesn't go through the normal startup path (which
does this in asm).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make declaration of mach_sched_init match definition
(which is in arch/m68knommu/kernel/setup.c).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is important to only provide the compat_ioctl method
if the downstream de->proc_fops does too, otherwise this
utterly confuses the logic in fs/compat_ioctl.c and we
end up doing the wrong thing.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Alexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
copy_from_user() returns the number of bytes not copied, hence 0 is the
expected output.
axi->mm might not be valid anymore when not equal to current->mm, do not
dereference before checking that - thanks to Al for spotting that.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
#x blocks expansion of macro argument, but it won't do you any
good if it's already been expanded... As it is, RFALSE(cond, ....)
ended up with stringified _expanded_ cond. Real fun when cond contains
something like le32_to_cpu() and you are on a big-endian box...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
... because somebody had added preempt.h -> list.h, resulting in
asm/system.h -> hardirq.h -> preempt.h -> list.h -> asm/system.h on m68k,
with smp_wmb() used in list.h and defined in asm/system.h below the include
of hardirq.h.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] Fix sclp_vt220 error handling.
[S390] cio: Reorganize initialization.
[S390] cio: Make CIO_* macros safe if dbfs are not available.
[S390] cio: Clean up messages.
[S390] Fix IRQ tracing.
[S390] vmur: fix diag14_read.
[S390] Wire up sys_fallocate.
[S390] add types.h include to s390_ext.h
[S390] cio: Remove deprecated rdc/rcd.
[S390] Get rid of new section mismatch warnings.
[S390] sclp: kill unused SCLP config option.
[S390] cio: Remove remains of _ccw_device_get_device_number().
[S390] cio: css_sch_device_register() can be made static.
[S390] Improve __smp_call_function_map.
[S390] Convert to smp_call_function_single.
Hans Verkuil